Search Results

Search found 26001 results on 1041 pages for 'local ip'.

Page 52/1041 | < Previous Page | 48 49 50 51 52 53 54 55 56 57 58 59  | Next Page >

• VPN instead of KVM over IP? [on hold]

  - by Blazer

  I have a server colocated on datacenter.CentOS operating system. They use KVM-ip when I need remote hands. Somoene told me that login using that will allow administrators (if they want) to get disk encryption password or ssh root pass via KVM-ip(is that true ?). Someone told me I can use VPN to login to my server instead of kvm over ip. Anyone have experience with that ? Is that option valid ? Thank you

  Read the article

• Why Wouldn't Root Be Able to Change a Zone's IP Address in Oracle Solaris 11?

  - by rickramsey

  You might assume that if you have root access to an Oracle Solaris zone, you'd be able to change the root's IP address. If so, you'd proceed along these lines ... First, you'd log in: root@global_zone:~# zlogin user-zone Then you'd remove the IP interface: root@user-zone:~# ipadm delete-ip vnic0 Next, you'd create a new IP interface: root@user-zone:~# ipadm create-ip vnic0 Then you'd assign the IP interface a new IP address (10.0.0.10): root@user-zone:~# ipadm create-addr -a local=10.0.0.10/24 vnic0/v4 ipadm: cannot create address: Permission denied Why would that happen? Here are some potential reasons: You're in the wrong zone Nobody bothered to tell you that you were fired last week. The sysadmin for the global zone (probably your ex-girlfriend) enabled link protection mode on the zone with this sweet little command: root@global_zone:~# dladm set-linkprop -p \ protection=mac-nospoof,restricted,ip-nospoof vnic0 How'd your ex-girlfriend learn to do that? By reading this article: Securing a Cloud-Based Data Center with Oracle Solaris 11 by Orgad Kimchi, Ron Larson, and Richard Friedman When you build a private cloud, you need to protect sensitive data not only while it's in storage, but also during transmission between servers and clients, and when it's being used by an application. When a project is completed, the cloud must securely delete sensitive data and make sure the original data is kept secure. These are just some of the many security precautions a sysadmin needs to take to secure data in a cloud infrastructure. Orgad, Ron, and Richard and explain the rest and show you how to employ the security features in Oracle Solaris 11 to protect your cloud infrastructure. Part 2 of a three-part article on cloud deployments that use the Oracle Solaris Remote Lab as a case study. About the Photograph That's the fence separating a small group of tourist cabins from a pasture in the small town of Tropic, Utah. Follow Rick on: Personal Blog | Personal Twitter | Oracle Forums   Follow OTN Garage on: Web | Facebook | Twitter | YouTube

  Read the article

• IIS7.5 + Wordpress + Restrict Access to wp-login.php by client IP address

  - by JuanValdez

  I am moving from an Apache host to IIS. One of my sites in Wordpress (running Multi-site) which give me multiple blogs. I have moved all my rules from my .htaccess to the Microsoft URL ReWrite module. I have one section left that will not import. I want to restrict access to all instances of the file wp-login.php by Client IP address. In my .htaccess file I did the following: <Files wp-login.php> Order Deny,Allow Deny from all Allow from 192.168 </Files> Any smart ideas on how to accompish this in IIS7.5?

  Read the article

• Newly installed Ruby gems not showing up in $LOAD_PATH

  - by randombits

  I'm using MacPorts in order to manage my Ruby/Rails/Gems installations. Recently after doing a gem install wirble, wirble fails to load when I start an instance of irb. Here's the output: $ irb --simple-prompt Couldn't load Wirble: no such file to load -- wirble The Wirble gem doesn't show up in my $LOAD_PATH: >> puts $: /opt/local/lib/ruby1.9/gems/1.9.1/gems/actionmailer-2.3.5/lib /opt/local/lib/ruby1.9/gems/1.9.1/gems/actionpack-2.3.5/lib /opt/local/lib/ruby1.9/gems/1.9.1/gems/activerecord-2.3.5/lib /opt/local/lib/ruby1.9/gems/1.9.1/gems/activeresource-2.3.5/lib /opt/local/lib/ruby1.9/gems/1.9.1/gems/activesupport-2.3.5/lib /opt/local/lib/ruby1.9/gems/1.9.1/gems/mysql-2.8.1/lib /opt/local/lib/ruby1.9/gems/1.9.1/gems/mysql-2.8.1/ext /opt/local/lib/ruby1.9/gems/1.9.1/gems/mysql-2.8.1/bin /opt/local/lib/ruby1.9/gems/1.9.1/gems/rack-1.0.1/bin /opt/local/lib/ruby1.9/gems/1.9.1/gems/rack-1.0.1/lib /opt/local/lib/ruby1.9/gems/1.9.1/gems/rails-2.3.5/bin /opt/local/lib/ruby1.9/gems/1.9.1/gems/rails-2.3.5/lib /opt/local/lib/ruby1.9/gems/1.9.1/gems/rake-0.8.7/bin /opt/local/lib/ruby1.9/gems/1.9.1/gems/rake-0.8.7/lib /opt/local/lib/ruby1.9/gems/1.9.1/gems/rubygems-update-1.3.7/hide_lib_for_update /opt/local/lib/ruby1.9/gems/1.9.1/gems/rubygems-update-1.3.7/bin /opt/local/lib/ruby1.9/site_ruby/1.9.1 /opt/local/lib/ruby1.9/site_ruby/1.9.1/i386-darwin10 /opt/local/lib/ruby1.9/site_ruby /opt/local/lib/ruby1.9/vendor_ruby/1.9.1 /opt/local/lib/ruby1.9/vendor_ruby/1.9.1/i386-darwin10 /opt/local/lib/ruby1.9/vendor_ruby /opt/local/lib/ruby1.9/1.9.1 /opt/local/lib/ruby1.9/1.9.1/i386-darwin10 . => nil >> The gem is definitely installed: $ gem list |grep -i wirble wirble (0.1.3) It is located in /opt/local/lib/ruby/gems/1.9.1/gems/wirble-0.1.3/ How do I get this and future gems I installed appended to my $LOAD_PATH?

  Read the article

• Cannot ping static ip on eth1

  - by Calvin Froedge

  I am trying to ping the network interface I have set up for eth1. This is my config: auto eth1 iface eth1 inet static address 192.168.1.2 netmask 255.255.255.0 gateway 192.168.1.1 broadcast 192.168.1.255 If I ping 192.168.1.2, I get: Ping 192.168.1.2 (192.168.1.2) 56(84) bytes of data. From 192.168.1.3 icmp_seq=3 Destination Host Unreachable Results of ifconfig tell me that the IPv4 address is 192.168.1.3. I can ping this ip. Bcast and Mask are as expected (same as in definition). I can ping 192.168.1.3 from my macbook. I cannot ping 192.168.1.2 locally or from my macbook. Any ideas why?

  Read the article

• SEO for Country & Language Specific content.

  - by kecebongsoft

  Currently I am creating a website which has a common topic for an article, but it's going to be different content for each country, and also, each of that content will be provided in several languages. And this mechanism exists in most of the parts in the website. For example, I have an article about tax. This article has to be different for each country, for example china. And tax content for china should be written in china AND english language (for non china-speaker). What is the best URL pattern to handle this? What I've been thinking is, using a sub folder (/country-code/language-code/) such as: www.example.com/cn/cn/tax www.example.com/cn/en/tax Or using top level domain such as: www.example.cn/cn/tax www.example.cn/en/tax Or subdomain such as cn.example.com/cn/tax cn.example.com/en/tax I think I will not prefer the last option since I might need to use subdomain for other purpose. Which left only subfolder and TLDN. I've read some articles saying that TLDN is good for localized content (language-specific content), but in my case, my TLDN will also has english contents (for non local speaker) which is specific only to that particular country (also the purpose of this is to let people from other country easily search it through google). What is the best pattern to pick and why?.

  Read the article

• Bingbot requests from Google IP address

  - by JITHIN JOSE

  We have some suspicious requests to our server, 74.125.186.46 - - [24/Aug/2014:23:24:11 -0500] "GET <url> HTTP/1.1" 200 16912 "-" "Mozilla/5.0 (compatible; bingbot/2.0; +http://www.bing.com/bingbot.htm)" 74.125.187.193 - - [24/Aug/2014:23:24:12 -0500] "GET <url> HTTP/1.1" 200 20119 "-" "Mozilla/5.0 (compatible; bingbot/2.0; +http://www.bing.com/bingbot.htm)" As it shows, user-agent shows it is bingbot. But whois data of IP address(74.125.186.46 and 74.125.187.193) shows it is from google servers. So is it Google,Bing or any other content scrappers?

  Read the article

• ban an IP temporarily after x-many incorrect password attempts

  - by sova

  My new web server got hacked (sigh). I have physical access to my machine (in the near future). It seems like the only changes was a new user account and a borked sudoers file. It seems as though the password was discovered by dictionary searching (I didn't pick it). After I fix these problems (or do a full reinstall?) I want to add a mechanism to ban an IP (for maybe 24 hours or some time limit) after getting the password wrong x number of times, but I'm not a unix sysadmin or anything, so I'm not really sure where to get started. The machine is running Lucid Lynx, from an Ubuntu minimal installation. Thanks,I appreciate your help guys. Hopefully this is the right place for this question.

  Read the article

• Assigning Static Public IP Address to Windows Server 2008

  - by Neeti

  Please help a newbie. I am new to windows server. I have an IBM server and I have installed Windows Server 2008 R2 on that. I am provided with a static IP address by my ISP. How I can assign that to my server? I have a webapplication hosted on the server which I require to access from the external world using internet browser. How can this be achieved? Please let me know if there are any tutorials or step by step guide for achieving what I am trying to.

  Read the article

• Standards for how developers work on their own workstations

  - by Jon Hopkins

  We've just come across one of those situations which occasionally comes up when a developer goes off sick for a few days mid-project. There were a few questions about whether he'd committed the latest version of his code or whether there was something more recent on his local machine we should be looking at, and we had a delivery to a customer pending so we couldn't wait for him to return. One of the other developers logged on as him to see and found a mess of workspaces, many seemingly of the same projects, with timestamps that made it unclear which one was "current" (he was prototyping some bits on versions of the project other than his "core" one). Obviously this is a pain in the neck, however the alternative (which would seem to be strict standards for how each developer works on their own machine to ensure that any other developer can pick things up with a minimum of effort) is likely to break many developers personal work flows and lead to inefficiency on an individual level. I'm not talking about standards for checked-in code, or even general development standards, I'm talking about how a developer works locally, a domain generally considered (in my experience) to be almost entirely under the developers own control. So how do you handle situations like this? Are the one of those things that just happens and you have to deal with, the price you pay for developers being allowed to work in the way that best suits them? Or do you ask developers to adhere to standards in this area - use of specific directories, naming standards, notes on a wiki or whatever? And if so what do your standards cover, how strict are they, how do you police them and so on? Or is there another solution I'm missing? [Assume for the sake of argument that the developer can not be contacted to talk through what he was doing here - even if he could knowing and describing which workspace is which from memory isn't going to be simple and flawless and sometimes people genuinely can't be contacted and I'd like a solution which covers all eventualities.]

  Read the article

• Help with Collision of spawned object(postion fixed) with objects that there are translating on screen

  - by Amrutha

  Hey guys I am creating a game using Corona SDK and so coding it in Lua. So there are 2 separate functions, To translate the hit objects and change their color when they are tapped The link below is the code I am using to for the first function http://developer.anscamobile.com/sample-code/fishies Spawn objects that will hit the translating objects on collision. Alos on collision the spawned object disappears and the translating object bears a color(indicating the collision). In addition the size of this spawned object is dependent on i/p volume level. The function I have written is as follows, --VOICE INPUT CODE local r = media.newRecording() r:startRecording() r:startTuner() --local function newBar() -- local bar = display.newLine( 0, 0, 1, 0 ) -- bar:setColor( 0, 55, 100, 20 ) -- bar.width = 5 -- bar.y=400 -- bar.x=20 -- return bar --end local c1 = display.newImage("str-minion-small.png") c1.isVisible=false local c2 = display.newImage("str-minion-mid.png") c2.isVisible=false local c3 = display.newImage("str-minion-big.png") c3.isVisible=false --SPAWNING local function spawnDisk( event ) local phase = event.phase local volumeBar = display.newLine( 0, 0, 1, 0 ) volumeBar.y = 400 volumeBar.x = 20 -- volumeBar.isVisible=false local v = 20*math.log(r:getTunerVolume()) local MINTHRESH = 30 local LEFTMARGIN = 20 local v2 = MINTHRESH + math.max (v, -MINTHRESH) v2 = (display.contentWidth - 1 * LEFTMARGIN ) * v2 / MINTHRESH volumeBar.xScale = math.max ( 20, v2 ) local l = volumeBar.xScale local cnt1 = 0 local cnt2 = 0 local cnt3 = 0 local ONE =1 local val = event.numTaps --local px=event.x --local py=event.y if "ended" == phase then --audio.play( popSound ) --myLabel.isVisible = false if l > 50 and l <=150 then -- c1:setFillColor(10,105,0) -- c1.isVisible=false c1.x=math.random( 10, 450 ) c1.y=math.random( 10, 300 ) physics.addBody( c1, { density=1, radius=10.0 } ) c1.isVisible=true cnt1= cnt1+ ONE return c1 elseif l > 100 and l <=250 then --c2:setFillColor(200,10,0) c2.x=math.random( 10, 450 ) c2.y=math.random( 10, 300 ) physics.addBody( c2, { density=2, radius=9000.0 } ) c2.isVisible=true cnt2= cnt2+ ONE return c2 elseif l >=250 then c3.x=math.random( 40, 450 ) c3.y=math.random( 40, 300 ) physics.addBody( c3, { density=2, radius=7000.0 , bounce=0.0 } ) c3.isVisible=true cnt3= cnt3+ ONE return c3 end end end buzzR:addEventListener( "touch", spawnDisk ) -- touch the screen to create disks Now both functions work fine independently but there is no collision happening. Its almost as if the translating object and the spawn object are on different layers. The translating object passes through the spawn object freely. Can anyone please tell me how to resolve this problem. And how can I get them to collide. Its my first attempt at game development, that too for a mobile platform so would appreciate all help. Also if I have not been specific do let me know. I ll try to frame the query better :). Thanks in advance.

  Read the article

• Foraward Traffic from local machine to proxy server using iptables

  - by Vaibhav

  I am using Ubuntu Server 12.04. My IP is 192.168.4.160. I want to route the HTTP traffic generated locally from my system destined to a particular URL (say x.x.x.x) to pass through proxy server. My proxy server is 192.168.0.13:3128. I added following rule in iptables sudo iptables -t nat -A OUTPUT -p tcp -d x.x.x.x --dport 80 -j DNAT --to 192.168.0.13:3128 However, this rule does not seem to work for me. I captured packet in wireshark and I saw that packet is still going to x.x.x.x I am not very much familiar with iptables, so please try to be specific. Thanks in advance

  Read the article

• Help with Collision of spawned object(postion fixed) with objects that there are translating on screen

  - by Amrutha

  Hey guys I am creating a game using Corona SDK and so coding it in Lua. So there are 2 separate functions, To translate the hit objects and change their color when they are tapped The link below is the code I am using to for the first function http://developer.anscamobile.com/sample-code/fishies Spawn objects that will hit the translating objects on collision. Alos on collision the spawned object disappears and the translating object bears a color(indicating the collision). In addition the size of this spawned object is dependent on i/p volume level. The function I have written is as follows: --VOICE INPUT CODE local r = media.newRecording() r:startRecording() r:startTuner() --local function newBar() -- local bar = display.newLine( 0, 0, 1, 0 ) -- bar:setColor( 0, 55, 100, 20 ) -- bar.width = 5 -- bar.y=400 -- bar.x=20 -- return bar --end local c1 = display.newImage("str-minion-small.png") c1.isVisible=false local c2 = display.newImage("str-minion-mid.png") c2.isVisible=false local c3 = display.newImage("str-minion-big.png") c3.isVisible=false --SPAWNING local function spawnDisk( event ) local phase = event.phase local volumeBar = display.newLine( 0, 0, 1, 0 ) volumeBar.y = 400 volumeBar.x = 20 --volumeBar.isVisible=false local v = 20*math.log(r:getTunerVolume()) local MINTHRESH = 30 local LEFTMARGIN = 20 local v2 = MINTHRESH + math.max (v, -MINTHRESH) v2 = (display.contentWidth - 1 * LEFTMARGIN ) * v2 / MINTHRESH volumeBar.xScale = math.max ( 20, v2 ) local l = volumeBar.xScale local cnt1 = 0 local cnt2 = 0 local cnt3 = 0 local ONE =1 local val = event.numTaps --local px=event.x --local py=event.y if "ended" == phase then --audio.play( popSound ) --myLabel.isVisible = false if l > 50 and l <=150 then --c1:setFillColor(10,105,0) --c1.isVisible=false c1.x=math.random( 10, 450 ) c1.y=math.random( 10, 300 ) physics.addBody( c1, { density=1, radius=10.0 } ) c1.isVisible=true cnt1= cnt1+ ONE return c1 elseif l > 100 and l <=250 then --c2:setFillColor(200,10,0) c2.x=math.random( 10, 450 ) c2.y=math.random( 10, 300 ) physics.addBody( c2, { density=2, radius=9000.0 } ) c2.isVisible=true cnt2= cnt2+ ONE return c2 elseif l >=250 then c3.x=math.random( 40, 450 ) c3.y=math.random( 40, 300 ) physics.addBody( c3, { density=2, radius=7000.0 , bounce=0.0 } ) c3.isVisible=true cnt3= cnt3+ ONE return c3 end end end buzzR:addEventListener( "touch", spawnDisk ) -- touch the screen to create disks Now both functions work fine independently but there is no collision happening. Its almost as if the translating object and the spawn object are on different layers. The translating object passes through the spawn object freely. Can anyone please tell me how to resolve this problem. And how can I get them to collide. Its my first attempt at game development, that too for a mobile platform so would appreciate all help. Also if I have not been specific do let me know. I'll try to frame the query better :). Thanks in advance.

  Read the article

• access vmware local server from internet

  - by goutham

  I have installed a ubuntu machine with apache server in Vmware-workstation Now how can I access apache server from internet using my IP. Details: network for vmware :NAT the ip address in ubuntu is 192.168.1.4 my host IP is *..239.232 if I type 192.168.1.4 in web browser I get the apache content... but if I type my host IP then I dont get it.. If I install a apache server on host(win7) I can access the host apache content with my host IP from anywhere .. I want to access the vmware apache content from internet using host IP ....

  Read the article

• VPN - force a selective range of ip to run on VPN (linux)

  - by Francesco

  Preface: I know there are similar question here and there however I'm a kind of newbie on Net stuff so I need an answer on this specific scenario, hoping that can help others too as it is a common problem Let say I cannot do anything on the local switch to change the local ip range, I don't want to use any complicate trick as use VMachine to hide the local ip range but I want to use net tools to solve the issue. Scenario my local net assign me an IP of this class 192.168.1.xxx (ex. 192.168.1.116) and my VPN (VPNC) assign me IP of same class 192.168.1.xxx (ex. 192.168.1.247) Obviously I need VPN to access local address (ex. 192.168.1.100) but when I open any address of the class 192.168.1.xx the route point to my local net and not to the VPN ones. I'm on linux and i'd like gui solution (network manager) in case it is not possible let play with route command. here what network manager offer me: Here my actual route once connected to the VPN: Here some route information (route -n) Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 0.0.0.0 0.0.0.0 U 0 0 0 ppp0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0 182.71.21.106 192.168.1.1 255.255.255.255 UGH 0 0 0 wlan0 182.71.21.106 192.168.1.1 255.255.255.255 UGH 0 0 0 wlan0 192.168.1.0 0.0.0.0 255.255.255.0 U 9 0 0 wlan0 192.168.1.246 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 Here my ifconfig : ppp0 Link encap:Point-to-Point Protocol inet addr:192.168.1.247 P-t-P:192.168.1.246 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1400 Metric:1 RX packets:3415 errors:0 dropped:0 overruns:0 frame:0 TX packets:2525 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:3682328 (3.6 MB) TX bytes:402315 (402.3 KB) wlan0 Link encap:Ethernet HWaddr 4c:eb:42:06:a3:a6 inet addr:192.168.1.116 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::4eeb:42ff:fe06:a3a6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:72598 errors:0 dropped:0 overruns:0 frame:0 TX packets:42300 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:76000532 (76.0 MB) TX bytes:13919400 (13.9 MB) The Question So basically I would like to add a rule to force this particular address (192.168.1.100) on the VPN and not on my local net

  Read the article

• outgoing DNS flood targeted to non-ISP hosts

  - by radudani

  Below is the specific traffic monitored at the network perimeter and originating from a user PC on Vista platform. My question is not about the effects of the flood, but about the nature of the source of it. Is this some known infection, or just an application went out of control? a standard NOD32 scan didn't find anything, as the user told me. Thank you for any hint. 14:40:10.115876 IP 192.168.7.42.4122 > 67.228.0.181.53: S 2742536765:2742536765(0) win 16384 <mss 1460,nop,nop,sackOK> 14:40:10.115943 IP 192.168.7.42.4124 > 67.228.181.207.53: S 3071079888:3071079888(0) win 16384 <mss 1460,nop,nop,sackOK> 14:40:10.116015 IP 192.168.7.42.4126 > 67.228.0.181.53: S 3445199428:3445199428(0) win 16384 <mss 1460,nop,nop,sackOK> 14:40:10.116086 IP 192.168.7.42.4128 > 67.228.181.207.53: S 2053198691:2053198691(0) win 16384 <mss 1460,nop,nop,sackOK> 14:40:10.116154 IP 192.168.7.42.4130 > 67.228.0.181.53: S 2841660872:2841660872(0) win 16384 <mss 1460,nop,nop,sackOK> 14:40:10.116222 IP 192.168.7.42.4132 > 67.228.181.207.53: S 3150822465:3150822465(0) win 16384 <mss 1460,nop,nop,sackOK> 14:40:10.116290 IP 192.168.7.42.4134 > 67.228.0.181.53: S 1692515021:1692515021(0) win 16384 <mss 1460,nop,nop,sackOK> 14:40:10.116358 IP 192.168.7.42.4136 > 67.228.181.207.53: S 3358275919:3358275919(0) win 16384 <mss 1460,nop,nop,sackOK> 14:40:10.116430 IP 192.168.7.42.4138 > 67.228.0.181.53: S 930184999:930184999(0) win 16384 <mss 1460,nop,nop,sackOK> 14:40:10.116498 IP 192.168.7.42.4140 > 67.228.181.207.53: S 1504984630:1504984630(0) win 16384 <mss 1460,nop,nop,sackOK> 14:40:10.116566 IP 192.168.7.42.4142 > 67.228.0.181.53: S 546074424:546074424(0) win 16384 <mss 1460,nop,nop,sackOK> 14:40:10.116634 IP 192.168.7.42.4144 > 67.228.181.207.53: S 4241828590:4241828590(0) win 16384 <mss 1460,nop,nop,sackOK> 14:40:10.116702 IP 192.168.7.42.4146 > 67.228.0.181.53: S 668634627:668634627(0) win 16384 <mss 1460,nop,nop,sackOK> 14:40:10.116769 IP 192.168.7.42.4148 > 67.228.181.207.53: S 3768119461:3768119461(0) win 16384 <mss 1460,nop,nop,sackOK> 14:40:10.117360 IP 192.168.7.42.4111 > 67.228.0.181.53: 12676 op8 Resp12*- [2128q][|domain] 14:40:10.117932 IP 192.168.7.42.4112 > 67.228.181.207.53: 44190 op7 NotAuth*|$ [29103q],[|domain] 14:40:10.118726 IP 192.168.7.42.4113 > 67.228.0.181.53: 49196 inv_q [b2&3=0xeea] [64081q] [28317a] [43054n] [23433au] Type63482 (Class 5889)? M-_^OS>M-JM-m^_M-i.[|domain] 14:40:10.119934 IP 192.168.7.42.4114 > 67.228.181.207.53: 48131 updateMA Resp12$ [43850q],[|domain] 14:40:10.121164 IP 192.168.7.42.4115 > 67.228.0.181.53: 46330 updateM% [b2&3=0x665b] [23691a] [998q] [32406n] [11452au][|domain] 14:40:10.121866 IP 192.168.7.42.4116 > 67.228.181.207.53: 34425 op7 YXRRSet* [39927q][|domain] 14:40:10.123107 IP 192.168.7.42.4117 > 67.228.0.181.53: 56536 notify+ [b2&3=0x27e6] [59761a] [23005q] [33341n] [29705au][|domain] 14:40:10.123961 IP 192.168.7.42.4118 > 67.228.181.207.53: 19323 stat% [b2&3=0x14bb] [32491a] [41925q] [2038n] [5857au][|domain] 14:40:10.132499 IP 192.168.7.42.4119 > 67.228.0.181.53: 50432 updateMA+ [b2&3=0x6bc2] [10733a] [9775q] [46984n] [15261au][|domain] 14:40:10.133394 IP 192.168.7.42.4120 > 67.228.181.207.53: 2171 notify Refused$ [26027q][|domain] 14:40:10.134421 IP 192.168.7.42.4121 > 67.228.0.181.53: 25802 updateM NXDomain*-$ [28641q][|domain] 14:40:10.135392 IP 192.168.7.42.4122 > 67.228.181.207.53: 2073 updateMA+ [b2&3=0x6d0b] [43177a] [54332q] [17736n] [43636au][|domain] 14:40:10.136638 IP 192.168.7.42.4123 > 67.228.0.181.53: 15346 updateD+% [b2&3=0x577a] [61686a] [19106q] [15824n] [37833au] Type28590 (Class 64856)? [|domain] 14:40:10.137265 IP 192.168.7.42.4124 > 67.228.181.207.53: 60761 update+ [b2&3=0x2b66] [43293a] [53922q] [23115n] [11349au][|domain] 14:40:10.148122 IP 192.168.7.42.4125 > 67.228.0.181.53: 3418 op3% [b2&3=0x1a92] [51107a] [60368q] [47777n] [56081au][|domain]

  Read the article

• Local Events | Azure Bootcamp

  - by Jeff Julian

  Coming to Kansas City April 8th and 9th is the Microsoft Azure Bootcamp. This event looks very promising for those developers who are looking into Azure for themselves or their companies. It covers the wide range of topics required to understand what Azure really is and is not. Space is limited so if you are considering Azure, register for this event today.Agenda:Module 1: Introduction to cloud computer and AzureHow it worksKey ScenariosThe development environment and SDKModule 2: Using Web RolesBasic ASP.NETBasic configurationModule 3: Blobs: File Storage in the cloudModule 4: Tables: Scalable hierarchical storageModule 5: Queues: Decoupling your systemsModule 6: Basic Worker RolesExecuting backend processesConsuming a queueLeveraging local storageModule 7: Advanced Worker RolesExternal EndpointsInter-role communicationModule 8: Building a business with AzureUsing Azure as an ISV or a partnerAdvantages to delivering valueBPOSPricingModule 9: SQL AzureSetting it upSQL Azure firewallRemote managementMigrating dataModule 10: AppFabricService BusAccess Control SystemIdentity in the cloudModule 11: Cloud ScenariosApp migration strategiesDisposable computingDynamic scaleShuntingPrototypingMultitenant applications (This is my second attempt at this post after MacJournal decided to crash and not save my work. Authoring tools all need auto-save features by now, that is a requirement set in stone by Microsoft Word 97) Related Tags: Azure, Microsoft, Kansas City

  Read the article

• JavaScript local alias pattern

  Heres a little pattern that is fairly common from JavaScript developers but that is not very well known from C# developers or people doing only occasional JavaScript development. In C#, you can use a using directive to create aliases of namespaces or bring them to the global scope: namespace Fluent.IO { using System; using System.Collections; using SystemIO = System.IO; In JavaScript, the only scoping construct there is is the function, but it can also be used as a local aliasing...Did you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

  Read the article

• JavaScript local alias pattern

  Heres a little pattern that is fairly common from JavaScript developers but that is not very well known from C# developers or people doing only occasional JavaScript development. In C#, you can use a using directive to create aliases of namespaces or bring them to the global scope: namespace Fluent.IO { using System; using System.Collections; using SystemIO = System.IO; In JavaScript, the only scoping construct there is is the function, but it can also be used as a local aliasing...Did you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

  Read the article

• Testing on Device Other Than the Known Brand Question (Local and Imported Phone Question)

  - by David Dimalanta

  I have a question. When testing a device by using Eclipse, it's easy to install and add device software with these specific brands commonly used in game testing like Samsung, Google, T-Mobile, and HTC; according to the Android Developers website. What if I'm using other brands that runs on Android to test the program via Eclipse (i.e. MyPhone, Starmobile), what should I look for to download in order to enable testing phones that those brands are using other than the brands that are known and commonly used: model number or simply brand? Here's some examples of these brands other than the brands we've known that runs on Android: Starmobile Engage 7 (http://www.lazada.com.ph/Starmobile-Engage-7-Android-40-4GB-with-Wi-Fi-Black-Starmobile-Mercury-B201-COMBO-39833.html/) My|Phone A898 Duo (http://www.myphone.com.ph/#!a898-duo/c1yt) Also, take note that I'm a Filipino programmer working at the Philippines to test our local smartphones for the created Android game or app. Hope you can understand me for my help.

  Read the article

• Good and easy way to share files on local machine

  - by jb

  I would like to have a directory that has following properties: Many users can copy files into it These files can be deleted/changed by these users (user A can delete/modify file that was copied into this directory) it cant be done using normal file permissions (because permissions are retained on copy). Here is what I found on the net: brainstorm idea blueprint Some use cases: Sharing music on local machine Simple git repository sharing (just make a bare repository writeable to many people) --- i know that there are solutions like gitosis Allow many developers to modify test instance of php app without giving them root (i guess they would copy files) --- I'm leading a team of nonprofit junior developers and I need to keep that one simple! EDIT AFAIK setting SGID bit is not enugh, it only affects newly created files --- and basic workflow for these use cases ivnolves copying and other operations (which cleave file's gid unchanged)

  Read the article

• Transfer domains without disrupting local email server

  - by krosiris

  Perhaps I am thinking about this wrong, but maybe some of you guys can help me on this one. I have a client who currently has a domain from network solutions and is hosted via GoDaddy. Additionally, he his has email service with GoDaddy as well, but it seems to be forwarded to his local server at work. How can I transfer hosting accounts without disrupting email service (or at least temporarily)? Some MX info via Godaddy: A @ Points to GoDaddy Host main Points to client's home server sw Points to client's home server MX @ Points to main.example.com @ Points to smtp.secureserver @ Points to mailstore1.secureserver

  Read the article

• Unable to PPTP through NAT on Cisco 881

  - by MasterRoot24

  I'm trying to connect to a PPTP server which is sat behind a Cisco 881 NAT router. The server is running Ubuntu Server 12.04 and is running Poptop pptpd as the PPTP daemon listening for connections. As discussed in my other question, I'm trying to setup a Cisco 881 router to replace my old Linksys WAG320N. This same server and WAN connection worked fine with the WAG320N with no special configuration, other than allowing 1723 in through the firewall. On the Cisco 881, I'm using the newer ip nat enable or NAT NVI to setup static routes in through the firewall for the services running behind the router. My reason being that I can't run another copy of my live DNS domains internally with local IP addresses in. For the purposes of this question, though, I have rebuilt the router with ip nat inside/outside style NAT'ing, but this issue is still apparent. HTTP/SMTP/IMAP etc. all work ok from both the WAN and LAN interfaces of the router. I'm only having issues with SIP (see other question) and PPTP. My issue is that the GRE doesn't appear to be passing through NAT correctly and one end of the connection is not receiving GRE traffic when it should be, so the server hangs up the connection. Here's an example of /var/log/syslog with debug enabled in /etc/pptpd.conf: Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: MGR: Launching /usr/sbin/pptpctrl to handle client Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: local address = 192.168.1.50 Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: remote address = 192.168.1.51 Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: pppd options file = /etc/ppp/pptpd-options Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Client 82.132.248.216 control connection started Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Received PPTP Control Message (type: 1) Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Made a START CTRL CONN RPLY packet Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: I wrote 156 bytes to the client. Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Sent packet to client Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Received PPTP Control Message (type: 7) Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Set parameters to 100000000 maxbps, 64 window size Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Made a OUT CALL RPLY packet Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Starting call (launching pppd, opening GRE) Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: pty_fd = 6 Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: tty_fd = 7 Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: I wrote 32 bytes to the client. Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: CTRL: Sent packet to client Dec 11 21:06:30 <HOSTNAME> pptpd[22627]: CTRL (PPPD Launcher): program binary = /usr/sbin/pppd Dec 11 21:06:30 <HOSTNAME> pptpd[22627]: CTRL (PPPD Launcher): local address = 192.168.1.50 Dec 11 21:06:30 <HOSTNAME> pptpd[22627]: CTRL (PPPD Launcher): remote address = 192.168.1.51 Dec 11 21:06:30 <HOSTNAME> pppd[22627]: Plugin /usr/lib/pptpd/pptpd-logwtmp.so loaded. Dec 11 21:06:30 <HOSTNAME> pppd[22627]: pppd 2.4.5 started by root, uid 0 Dec 11 21:06:30 <HOSTNAME> pppd[22627]: Using interface ppp0 Dec 11 21:06:30 <HOSTNAME> pppd[22627]: Connect: ppp0 <--> /dev/pts/3 Dec 11 21:06:30 <HOSTNAME> pptpd[22626]: GRE: Bad checksum from pppd. Dec 11 21:06:31 <HOSTNAME> pptpd[22626]: CTRL: Received PPTP Control Message (type: 15) Dec 11 21:06:31 <HOSTNAME> pptpd[22626]: CTRL: Got a SET LINK INFO packet with standard ACCMs Dec 11 21:07:00 <HOSTNAME> pppd[22627]: LCP: timeout sending Config-Requests Dec 11 21:07:00 <HOSTNAME> pppd[22627]: Connection terminated. Dec 11 21:07:00 <HOSTNAME> avahi-daemon[1042]: Withdrawing workstation service for ppp0. Dec 11 21:07:00 <HOSTNAME> pppd[22627]: Modem hangup Dec 11 21:07:00 <HOSTNAME> pppd[22627]: Exit. Dec 11 21:07:00 <HOSTNAME> pptpd[22626]: GRE: read(fd=6,buffer=6075a0,len=8196) from PTY failed: status = -1 error = Input/output error, usually caused by unexpected termination of pppd, check option syntax and pppd logs Dec 11 21:07:00 <HOSTNAME> pptpd[22626]: CTRL: PTY read or GRE write failed (pty,gre)=(6,7) Dec 11 21:07:00 <HOSTNAME> pptpd[22626]: CTRL: Reaping child PPP[22627] Dec 11 21:07:00 <HOSTNAME> pptpd[22626]: CTRL: Client 82.132.248.216 control connection finished Dec 11 21:07:00 <HOSTNAME> pptpd[22626]: CTRL: Exiting now Dec 11 21:07:00 <HOSTNAME> pptpd[5803]: MGR: Reaped child 22626 As far as Cisco are concerned, all I need is ip nat source static tcp <SERVER LAN IP> 1723 interface FastEthernet4 1723 but of course this doesn't seem to the be helping the GRE traffic through as it should. Trying the connection to the LAN IP of the server from the same LAN as the server (behind the router), the PPTP connection works fine, so I'm confident that the server's config is ok. Furthermore, all I needed on my WAG320N was to open 1723 in the firewall. Here's my current router config: ! ! Last configuration change at 20:20:15 UTC Tue Dec 11 2012 by xxx version 15.2 no service pad service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname xxx ! boot-start-marker boot-end-marker ! ! enable secret 4 xxxx ! aaa new-model ! ! aaa authentication login local_auth local ! ! ! ! ! aaa session-id common ! memory-size iomem 10 ! crypto pki trustpoint TP-self-signed-xxx enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-xxx revocation-check none rsakeypair TP-self-signed-xxx ! ! crypto pki certificate chain TP-self-signed-xxx certificate self-signed 01 xxx quit ip gratuitous-arps ip auth-proxy max-login-attempts 5 ip admission max-login-attempts 5 ! ! ! ! ! ip domain list dmz.xxx.local ip domain list xxx.local ip domain name dmz.xxx.local ip name-server 192.168.1.x ip cef login block-for 3 attempts 3 within 3 no ipv6 cef ! ! multilink bundle-name authenticated license udi pid CISCO881-SEC-K9 sn xxx ! ! username admin privilege 15 secret 4 xxx username joe secret 4 xxx ! ! ! ! ! ip ssh time-out 60 ! ! ! ! ! ! ! ! ! interface FastEthernet0 no ip address ! interface FastEthernet1 no ip address ! interface FastEthernet2 no ip address ! interface FastEthernet3 switchport access vlan 2 no ip address ! interface FastEthernet4 ip address dhcp ip nat enable duplex auto speed auto ! interface Vlan1 ip address 192.168.1.x 255.255.255.0 no ip redirects no ip unreachables no ip proxy-arp ip nat enable ! interface Vlan2 ip address 192.168.0.x 255.255.255.0 ! ip forward-protocol nd ip http server ip http access-class 1 ip http authentication local ip http secure-server ! ! ip nat source list 1 interface FastEthernet4 overload ip nat source list 2 interface FastEthernet4 overload ip nat source static tcp 192.168.1.x 1723 interface FastEthernet4 1723 ! ! access-list 1 permit 192.168.0.0 0.0.0.255 access-list 2 permit 192.168.1.0 0.0.0.255 ! ! ! ! control-plane ! ! banner motd Authorized Access only ! line con 0 exec-timeout 15 0 login authentication local_auth line aux 0 exec-timeout 15 0 login authentication local_auth line vty 0 4 access-class 2 in login authentication local_auth length 0 transport input all ! ! end UPDATE 16/12/2012: The only progress that I have been able to make on this issue is that I'm confident that the issue is caused by the GRE tunnels (which are required for the PPTP connection to complete) are being blocked. When attempting a connection, I can see in show ip nat nvi translations that both a TCP translation on 1723 is setup and also a GRE translation is setup also. I appear to be able to see GRE related packets on the LAN that the server is on, so I am lead to believe that the server is sending(?) GRE packets, however running Wireshark on a client PC when attempting a connection shows absolutely no GRE packets. Whilst there are no configuration directives in my config posted above (that I can pin point) which would specifically block them, it would appear that the GRE packets are not being allowed in/out of the router's firewall, even though a NAT translation entry is setup to the server's LAN address. Would anyone be able to provide me with some help to ensure that GRE packets are not blocked by the router's firewall, so that this can be ruled out as a possible issue please?

  Read the article

• Copy hangs in local network

  - by umpirsky

  I want to copy files from one Ubuntu system to another.They are both in local wireless network. I shared entire home dir on one, and tried to copy some files to another. It works for some time and then it just hangs at some point. I use Nautilus to copy files. Here is the example screenshot, it just hangs like this: After I cancel, Nautilus icon in lauchbar keeps progress bar, so I guess there is some problem. What can be the problem?

  Read the article

• Setting Up and Managing Local IPS Repositories

  - by user12244672

  My colleague, Albert White, has published a useful article detailing how to set up local IPS repositories for use within an enterprise: How to Create Multiple Internal Repositories for Oracle Solaris 11 This is useful as most servers will not be directly connected to the Internet and most customers will want to control which Oracle Solaris SRUs (Support Repository Updates) are "qualified" for deployment within their organization.  Setting up and managing Internal IPS (Image Packaging System) Repositories is the way to do this. The concept can naturally be extended and adapted.  For example, Albert talks about a "Development" Repo containing the latest Oracle Solaris 11 deliverables.  When qualifying a software level for deployment across the enterprise, a copy of a specific level could be taken, e.g. "GoldenImage2012Q3" or "SRU8.5", and once it passes testing, be used to deploy across the enterprise. Best Wishes, Gerry.

  Read the article

< Previous Page | 48 49 50 51 52 53 54 55 56 57 58 59  | Next Page >