Search Results

Search found 17314 results on 693 pages for 'vpn setup'.

Page 521/693 | < Previous Page | 517 518 519 520 521 522 523 524 525 526 527 528  | Next Page >

• Nvidia driver overscan issue second monitor via dvi-d cable

  - by benmichael

  Ok, I know that I have a bit of a bizarre setup, but here goes. I have an old laptop, HP Pavilion 6000. The graphics card in there is a GeForce 7150M. The monitor connection is an old 18pin. The external monitor I use is a Samsung SyncMaster 2333. Don't ask me why, but this monitor only has a dvi-d connection (yes, i have searched it). So I have the monitor plugged into the laptop. If I use any of the Nvidia propriety drivers and try to set the resolution up to 1920x1080 (the monitor's native resolution), I get a massive overscan issue. Over the years I have tried to get this to work, tinkering with my xorg.conf to death. I have also tried this on every Ubuntu since 10.04, on all the corresponding LUbuntus, and on all the Linux Mints since Lisa. Exact same issue. I have even tried it in WinDoze and it works perfectly there (although I did get the error once, but was unable to reproduce it). Using the Open Source drivers it works perfectly iff I switch off the laptop monitor (this makes no difference with the Nvidia drivers). I would have happily gone on using the Open Source drivers, except that since upgrading to LUbuntu 12.10, the Open Source drivers make my monitor completely hazy and have the same overscan issue until I (through the haze, only because I know where things are) go to the monitor settings, activate the laptop's monitor, then deactivate it, and suddenly it comes right. I have to do this every time. So I have to find a way to fix one of them, so I may as well tackle the propriety drivers, hence this overlong question. Amidst other things, I have tried the nvidia-settings, but because it is connected to an 18pin, it detects the monitor as a vga monitor and does not give me overscan correction options. I have tried custom modlines (although there are always more of those try), I have tried using xrandr, and I have tried all the FlatPanelOptions. What I have not tried is a Gentoo build, as I don't have time any more to do that installation, but up to about three years ago when I ran Gentoo exclusively I did not have this issue. Below is an link to an image with a red highlight around the portion of the screen visible to me, the numbers around it are the number of pixels which are cut off. This does seem to drift a few pixels every now and then. Thanks in advance. Nvidia driver issue image

  Read the article

• why are my players drawn top the side of my viewport

  - by Jetbuster

  Following this admittedly brilliant and clean 2d camera class I have a camera on each player, and it works for multiplayer and i've divided the screen into two sections for split screen by giving each camera a viewport. However in the game it looks like this I'm not sure if thats their position relative to the screen or what The relevant gameScreen code, the makePlayers is setup so it could theoretically work for up to 4 players private void makePlayers() { int rowCount = 1; if (NumberOfPlayers > 2) rowCount = 2; players = new Player[NumberOfPlayers]; for (int i = 0; i < players.Length; i++) { int xSize = GameRef.Window.ClientBounds.Width / 2; int ySize = GameRef.Window.ClientBounds.Height / rowCount; int col = i % rowCount; int row = i / rowCount; int xPoint = 0 + xSize * row; int yPoint = 0 + ySize * col; Viewport viewport = new Viewport(xPoint, yPoint, xSize, ySize); Vector2 playerPosition = new Vector2(viewport.TitleSafeArea.X + viewport.TitleSafeArea.Width / 2, viewport.TitleSafeArea.Y + viewport.TitleSafeArea.Height / 2); players[i] = new Player(playerPosition, playerSprites[i], GameRef, viewport); } //players[1].Keyboard = true; } public override void Draw(GameTime gameTime) { base.Draw(gameTime); foreach (Player player in players) { GraphicsDevice.Viewport = player.PlayerCamera.ViewPort; GameRef.spriteBatch.Begin(SpriteSortMode.Immediate, BlendState.AlphaBlend, SamplerState.PointClamp, null, null, null, player.PlayerCamera.Transform); map.Draw(GameRef.spriteBatch); // Draw the Player player.Draw(GameRef.spriteBatch); // Draw UI screen elements GraphicsDevice.Viewport = Viewport; ControlManager.Draw(GameRef.spriteBatch); GameRef.spriteBatch.End(); } } the player's initialize and draw methods are like so internal void Initialize() { this.score = 0; this.angle = (float)(Math.PI * 0 / 180);//Start sprite at it's default rotation int width = utils.scaleInt(picture.Width, imageScale); int height = utils.scaleInt(picture.Height, imageScale); this.hitBox = new HitBox(new Vector2(centerPos.X - width / 2, centerPos.Y - height / 2), width, height, Color.Black, game.Window.ClientBounds); playerCamera.Initialize(); } #region Methods public void Draw(SpriteBatch spriteBatch) { //Console.WriteLine("Hitbox: X({0}),Y({1})", hitBox.Points[0].X, hitBox.Points[0].Y); //Console.WriteLine("Image: X({0}),Y({1})", centerPos.X, centerPos.Y); Vector2 orgin = new Vector2(picture.Width / 2, picture.Height / 2); hitBox.Draw(spriteBatch); utils.DrawCrosshair(spriteBatch, Position, game.Window.ClientBounds, Color.Red); spriteBatch.Draw(picture, Position, null, Color.White, angle, orgin, imageScale, SpriteEffects.None, 0.1f); } as I said I think I'm gonna need to do something with the render position but I'm to entirely sure what or how it would be elegant to say the least

  Read the article

• How to deal with MySQL Connector/ODBC error "Can't connect to local MySQL server through socket '/var/lib/mysql/mysql.sock'"

  - by user12653020

  I am sure many users run into a mysterious problem when perfectly working ODBC configurations started failing with errors like: Can't connect to local MySQL server through socket '/var/lib/mysql/mysql.sock' The above error message might be preceded with something like [nxDc[yQ]. At the same time odbc.ini specifies in its DSN different SOCKET=/tmp/mysql.sock or a TCP connection SERVER=<remote_host_or_ip>. The question is, what had happened that the ODBC driver started to ignore the DSN options? The clue lies in the corrupted string [nxDc[yQ], which actually was [UnixODBC][MySQL] with each 2nd symbol removed. This is the case of bad conversion from SQLCHAR to SQLWCHAR. The UnixODBC driver manager took a single-byte character string from the client application and tried to convert it into the wide (multi-byte) characters for the Unicode version of MyODBC driver: Initially the piece of the connection string was represented by 1-byte chars like: [S][E][R][V][E][R][=][m][y][h][o][s][t][;] after the bad conversion to wide chars (commonly 2-byte UTF-16) [SE][RV][ER][=m][yh][os][t;] instead of [S\0][E\0][R\0][V\0][E\0][R\0][=\0][m\0][y\0][h\0][o\0][s\0][t\0][;\0] Naturally, the MyODBC driver could not parse the bad string and tried to use the default connection type (SOCKET) with the default value (/var/lib/mysql/mysql.sock) Now we know what happened, but why it happened? In most cases it happened because of using ODBCManageDataSourcesQ4 utility or its older analog ODBCConfig. When registering ODBC drivers they put lots of additional options and one of these options badly affects the UnixODBC driver manager itself. The solution is simple - remove or comment out the option in odbcinst.ini file (it is empty by default) set for the driver: [MySQL ODBC 5.2.6 Driver] Description    = Driver         = /home/dbs/myodbc526/lib/libmyodbc5w.so Driver64       = /home/dbs/myodbc526/lib/libmyodbc5w.so Setup          = /home/dbs/myodbc526/lib/libmyodbc5S.so Setup64        = /home/dbs/myodbc526/lib/libmyodbc5S.so UsageCount     = 1 CPTimeout      = 0 CPTimeToLive   = 0 IconvEncoding  =  # <--------- remove this line Trace          = TraceFile      = TraceLibrary   = After applying this simple solution (remove the line with IconvEncoding = ) everything came to normal. Prior to removing that line I tried putting different encoding names there, but the result was not good, so I really don't know how to properly use it. Unfortunately, UnixODBC manuals say nothing about it. Therefore, removing this option was the only way to get things done.

  Read the article

• Two New CRM USER Communities just launched

  - by Divya Malik

  Here comes an announcement from Chris Gallen, from our Support Services team. For those of you who are EBS CRM users, here are two new recently launched communities that are now available to discuss topics that are important to you. These communities are for Sales & Marketing and  Telesales  The Sales & Marketing community is open to discuss a wide range of topics from Oracle Sales, Sales Online, Territory Management, Partner Management, Leads Management, Sales Offline, Sales for Handhelds, Sales Foundation, and Oracle Marketing. Some possible topics include Oracle Sales Implementations, TCA and DQM Integrations, Territory Management Setups and Definitions, Product Catalog Integrations, Sales Forecasting, Lead and Opportunity management, Sales Manager and Sales User responsibilities and Reports, Resource Management including Roles and Groups, Oracle Sales Personalizations, Concurrent Requests for Sales Reps and Sales Manager Dashboards, Integration with Quoting, Proposals, General Ledger, Advanced Product Catalog, CRM Resource Administration, etc. The Telesales community is available to discuss topics such as Customer/Org/Person/Party Relationships, TCA/DQM Integration, Lead and Opportunity Management, Universal Work Queue, Universal Search Features, Purchase Items/Product Integration, eBusiness Center Setup Issues, Interactions, Tasks and Notes Integrations, and Form Personalizations. How Can You Get Started? Here are the two ways to get engaged. A) Click here to access all our communities  OR B) My Oracle Support as follows: Log into My Oracle Support (Flash or Classic).                                                                                                                           Click the "Community" link at the top of the page. Click [Enter Here] on the following page. Select the community from the "My Communities" list on the top-left. Take advantage TODAY!

  Read the article

• Multi subnet in ubuntu with dnsmasq

  - by Fox Mulder

  I have a multi lan port box that install ubuntu server 11.10. I am setup network in /etc/network/interfaces file as follow: auto lo iface lo inet loopback auto eth0 iface eth0 inet static      address 192.168.128.254      netmask 255.255.255.0      network 192.168.128.0      broadcast 192.168.128.255      gateway 192.168.128.1      dns-nameservers xxxxxx auto eth1 iface eth1 inet static      address 192.168.11.1      netmask 255.255.255.0      network 192.168.11.0      broadcast 192.168.11.255 auto eth2 iface eth2 inet static      address 192.168.21.1      netmask 255.255.255.0      network 192.168.21.0      broadcast 192.168.21.255 auto eth3 iface eth3 inet static      address 192.168.31.1      netmask 255.255.255.0      network 192.168.31.0      broadcast 192.168.31.255 I am also enable the ip forward by echo 1 /proc/sys/net/ipv4/if_forward in rc.local. my dnsmasq config as follow except-interface=eth0 dhcp-range=interface:eth1,set:wifi,192.168.11.101,192.168.11.200,255.255.255.0 dhcp-range=interface:eth2,set:kids,192.168.21.101,192.168.21.200,255.255.255.0 dhcp-range=interface:eth3,set:game,192.168.31.101,192.168.31.200,255.255.255.0 the dhcp was working fine in eth1,eth2,eth3, any machine plug in the subnet can get correct subnet's ip. My problem was, each subnet machine can't ping each other. for example. 192.168.11.101 can't ping 192.168.21.101 but can ping 192.168.128.1 192.168.31.101 can't ping 192.168.21.101 but can ping 192.168.128.1 I am also try to using route add -net 192.168.11.0 netmask 255.255.255.0 gw 192.168.11.1 (and also 192.168.21.0/192.168.31.0) at this multi-lan-port machine. But still won't work. Does anyone can help ? Thanks.

  Read the article

• Open GL polygons not displaying

  - by Darestium

  I have tried to follow nehe's opengl tutorial lesson 2. I use sfml for my window creation. The problem I have is that both the triangle and the quad don't show up on the screen: #include <SFML/System.hpp> #include <SFML/Window.hpp> #include <iostream> void processEvents(sf::Window *app); void processInput(sf::Window *app, const sf::Input &input); void renderCube(sf::Window *app, sf::Clock *clock); void renderGlScene(sf::Window *app); void init(); int main() { sf::Window app(sf::VideoMode(800, 600, 32), "Nehe Lesson 2"); app.UseVerticalSync(false); init(); while (app.IsOpened()) { processEvents(&app); renderGlScene(&app); app.Display(); } return EXIT_SUCCESS; } void init() { glClearDepth(1.f); glClearColor(0.f, 0.f, 0.f, 0.f); // Enable z-buffer and read and write glEnable(GL_DEPTH_TEST); glDepthMask(GL_TRUE); // Setup a perpective projection glMatrixMode(GL_MODELVIEW); glLoadIdentity(); gluPerspective(45.f, 1.f, 1.f, 500.f); glShadeModel(GL_SMOOTH); } void processEvents(sf::Window *app) { sf::Event event; while (app->GetEvent(event)) { if (event.Type == sf::Event::Closed) { app->Close(); } if (event.Type == sf::Event::KeyPressed && event.Key.Code == sf::Key::Escape) { app->Close(); } } } void renderGlScene(sf::Window *app) { app->SetActive(); glClear(GL_COLOR_BUFFER_BIT | GL_DEPTH_BUFFER_BIT); // Clear the screen and the depth buffer glLoadIdentity(); // Reset the view glTranslatef(-1.5f, 0.0f, -6.0f); // Move Left 1.5 units and into the screen 6.0 glBegin(GL_TRIANGLES); glVertex3f( 0.0f, 1.0f, 0.0f); // Top glVertex3f(-1.0,-1.0f, 0.0f); // Bottom Left glVertex3f( 1.0f,-1.0f, 0.0f); // Bottom Right glEnd(); glTranslatef(3.0f, 0.0f, 0.0f); glBegin(GL_QUADS); // Draw a quad glVertex3f(-1.0f, 1.0f, 0.0f); glVertex3f( 1.0f, 1.0f, 0.0f); glVertex3f( 1.0f,-1.0f, 0.0f); glVertex3f(-1.0f,-1.0f, 0.0f); glEnd(); } I would greatly appreciate it if someone could help me resolve my issue.

  Read the article

• Rendering Texture Quad to Screen or FBO (OpenGL ES)

  - by Usman.3D

  I need to render the texture on the iOS device's screen or a render-to-texture frame buffer object. But it does not show any texture. It's all black. (I am loading texture with image myself for testing purpose) //Load texture data UIImage *image=[UIImage imageNamed:@"textureImage.png"]; GLuint width = FRAME_WIDTH; GLuint height = FRAME_HEIGHT; //Create context void *imageData = malloc(height * width * 4); CGColorSpaceRef colorSpace = CGColorSpaceCreateDeviceRGB(); CGContextRef context = CGBitmapContextCreate(imageData, width, height, 8, 4 * width, colorSpace, kCGImageAlphaPremultipliedLast | kCGBitmapByteOrder32Big); CGColorSpaceRelease(colorSpace); //Prepare image CGContextClearRect(context, CGRectMake(0, 0, width, height)); CGContextDrawImage(context, CGRectMake(0, 0, width, height), image.CGImage); glGenTextures(1, &texture); glBindTexture(GL_TEXTURE_2D, texture); glTexParameteri(GL_TEXTURE_2D, GL_TEXTURE_MIN_FILTER, GL_NEAREST); glTexImage2D(GL_TEXTURE_2D, 0, GL_RGBA, width, height, 0, GL_RGBA, GL_UNSIGNED_BYTE, imageData); glTexParameterf(GL_TEXTURE_2D, GL_TEXTURE_WRAP_S, GL_CLAMP_TO_EDGE); glTexParameterf(GL_TEXTURE_2D, GL_TEXTURE_WRAP_T, GL_CLAMP_TO_EDGE); Simple Texture Quad drawing code mentioned here //Bind Texture, Bind render-to-texture FBO and then draw the quad const float quadPositions[] = { 1.0, 1.0, 0.0, -1.0, 1.0, 0.0, -1.0, -1.0, 0.0, -1.0, -1.0, 0.0, 1.0, -1.0, 0.0, 1.0, 1.0, 0.0 }; const float quadTexcoords[] = { 1.0, 1.0, 0.0, 1.0, 0.0, 0.0, 0.0, 0.0, 1.0, 0.0, 1.0, 1.0 }; // stop using VBO glBindBuffer(GL_ARRAY_BUFFER, 0); // setup buffer offsets glVertexAttribPointer(ATTRIB_VERTEX, 3, GL_FLOAT, GL_FALSE, 3*sizeof(float), quadPositions); glVertexAttribPointer(ATTRIB_TEXCOORD0, 2, GL_FLOAT, GL_FALSE, 2*sizeof(float), quadTexcoords); // ensure the proper arrays are enabled glEnableVertexAttribArray(ATTRIB_VERTEX); glEnableVertexAttribArray(ATTRIB_TEXCOORD0); //Bind Texture and render-to-texture FBO. glBindTexture(GL_TEXTURE_2D, GLid); //Actually wanted to render it to render-to-texture FBO, but now testing directly on default FBO. //glBindFramebuffer(GL_FRAMEBUFFER, textureFBO[pixelBuffernum]); // draw glDrawArrays(GL_TRIANGLES, 0, 2*3); What am I doing wrong in this code? P.S. I'm not familiar with shaders yet, so it is difficult for me to make use of them right now.

  Read the article

• What actions does Ubuntu trigger when battery is low?

  - by blueyed

  When the battery is low, the screen gets dimmed after a few seconds already. This appears to be some special power-saving mode, and might be related to the time in org.gnome.settings-daemon.plugins.power.time-low (1200 seconds (20 minutes) the default). While this seems to get triggered by gnome-settings-daemon, I wonder what else Ubuntu does when this happens (e.g. via DBus listeners), or other event listeners that look for a "low battery" state. It seems like something in this regard causes Ubuntu / X / the system to behave more sluggish afterwards (when the laptop is on AC again), and I would like to look into what might be causing this. I could not find anything related via dconf-editor, e.g. in org.gnome.settings-daemon.plugins.power. It appears to get setup via idle_configure in plugins/power/gsd-power-manager.c, but it's probably something more related to something that listens on the DBus interface, which gets notified via e.g.: if (!g_dbus_connection_emit_signal (manager->priv->connection, NULL, GSD_POWER_DBUS_PATH, "org.freedesktop.DBus.Properties", "PropertiesChanged", props_changed, &error)) I could imagine that some "power saving" property gets set, but not unset when AC is available anymore and/or the battery is not low anymore. I have looked at the CPU governor setting (/sys/devices/system/cpu/cpu*/cpufreq/scaling_governor), but it was ondemand. I am using gnome-settings-daemon with awesomeWM on Ubuntu 14.04. gnome-settings-daemon=3.8.6.1-0ubuntu11.1 I've also compared gsd's plugins/power/gsd-power-manager.c with the one from Debian's gnome-settings-daemon-3.12.1, but could not find anything obvious that might have been fixed/changed in this regard. I have managed to trigger the gnome-power-manager's gnome-settings plugin (which dims the screen etc), by patching upower and use it after killing the system's upower daemon. (note that it's probably only energy that is being used by gpm to calculate it by itself). It does not make the system become sluggish.. OTOH I have not heard the speaker's beeping, which might come from the BIOS, which might be involved here, too - or other programs using the kernel's interface on /sys/class/power_supply/BAT0/. --- src/linux/up-device-supply.c.orig 2014-06-07 16:48:32.735920661 +0200 +++ src/linux/up-device-supply.c 2014-06-07 16:48:39.391920525 +0200 @@ -821,6 +821,9 @@ supply->priv->energy_old_first = 0; } + percentage = 3.1f; + time_to_empty = 3*60; + energy = 5; g_object_set (device, "energy", energy, "energy-full", energy_full,

  Read the article

• How to generate SPMetal for a specific list (OOTB: like tasks or contacts) with custom columns

  - by KunaalKapoor

  SPMetal is used to make use of LINQ on a list in SharePoint 2010. By default when you generate SPMetal on a site you will get a code generated file for most of the lists and probably more. Here is a MSDN link for some info on SPMetal.http://msdn.microsoft.com/en-us/library/ee538255(office.14).aspxBut what if you want only to generate the code for one list?Well it is quite simple once you figure it out. You need to add an xml file to override the default settings of SPMetal and specify it in the /parameters option. I will show you how to do this.First create a Folder that will contain two files (GenerateSPMetalCode.bat and SPMetal.xml).Below is the content of the files:GenerateSPMetalCode.bat "C:\Program Files\Common Files\Microsoft Shared\Web Server Extensions\14\BIN\SPMetal" /web:http://YourServer /code:OutPutFileName.cs /language:csharp /parameters:SPMetal.xml pause SPMetal.xml <?xml version="1.0" encoding="utf-8"?> <Web AccessModifier="Internal" xmlns="http://schemas.microsoft.com/SharePoint/2009/spmetal"> <List Name="ListName"> <ContentType Name="ContentTypeName" Class="GeneratedClassName" /> </List> <ExcludeOtherLists></ExcludeOtherLists> </Web> You will have to change some of the text in the files so that it will be specific to your SharePoint Server Setup. In the bat file you will have to change http://YourServer to the url of the web where your list is. In the SPMetal.xml file you need to change ListName to the name of your list and the ContentTypeName to the name of the content type you want to extract. The GeneratedClassName can be anything but perhaps you should rename it to something more sensible.Adding the following line: '<List Name="ListName"><ContentType Name="ContentTypeName" Class="GeneratedClassName" /> </List>'  makes sure that any custom columns added to an OOTB list like contacts or tasks are also generated, which are missed out in a regular generation.So now when you run it the SPMetal command will read the SPMetal.xml list and override its commands. ExcludeOtherLists element makes it so that only the code for the lists you specify will be generated. For some reason I got an error if I had this element above the List element.You sould now have a code file called OutPutFileName.cs that has been generated. You can now put this in your SharePoint project for use with your LINQ queries against that list.I will soon write a LINQ example that uses the generated class. UPDATE: Add the /namespace parameter to add a namespace to the generated code. "C:\Program Files\Common Files\Microsoft Shared\Web Server Extensions\14\BIN\SPMetal" /web:http://YourServer /namespace:MySPMetalNameSpace /code:OutPutFileName.cs /language:csharp /parameters:SPMetal.xml

  Read the article

• Storing hierarchical template into a database

  - by pduersteler

  If this title is ambiguous, feel free to change it, I don't know how to put this in a one-liner. Example: Let's assume you have a html template which contains some custom tags, like <text_field />. We now create a page based on a template containing more of those custom tags. When a user wants to edit the page, he sees a text field. he can input things and save it. This looks fairly easy to set up. You either have something like a template_positions table which stores the content of those fields. Case: I now have a bit of a blockade keeping things as simple as possible. Assume you have the same tag given in your example, and additionally, <layout> and <repeat> tags. Here's an example how they should be used: <repeat> <layout name="image-left"> <image /> <text_field /> </layout> <layout name="image-right"> <text_field /> <image /> </layout> </repeat> We now have a block which can be repeated, obviously. This means: when creting/editing a page containing such a template block, I can choose between a layout image-left and image-right which then gets inserted as content element (where content for <image /> and <text_field /> gets stored). And because this is inside a <repeat>, content elements from the given layouts can be inserted multiple times. How do you store this? Simply said, this could be stored with the same setup I've wrote in the example above, I just need to add a parent_id or something similiar to maintain a hierarchy. but I think I am missing something. At least the relation between an inserted content element and the origin/insertion point is missing. And what happens when I update the template file? Do I have to give every custom tag that acts as editable part of a template an identifier that matches an identifier in the template to substitue them correctly? Or can you think of a clean solution that might be better?

  Read the article

• Showing ZFS some LOVE

  - by Kristin Rose

  Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} L is for the way you look at us, and O because we’re Oracle, but V is very, very, extra ordinary, and E, well that’s obvious… E is because Oracle’s new Sun ZFS Storage Appliance is Excellent, and here at OPN, we like spell out the obvious!  If you haven’t already heard, the Sun ZFS Appliance has “A simple, GUI-driven setup and configuration, solid price-performance and world-class Oracle support behind it. The CRN Test Center recommends the Sun ZFS Storage”. Read more about what CRN said here. Oracle's Sun ZFS Appliance family delivers enterprise-class network attached storage (NAS) capabilities with leading Oracle integration, simplicity, efficiency, performance, and TCO.  The systems offer an easy way to manage and expand your storage environment at a lower cost, with more efficiency, better data integrity, and higher performance when compared with competitive NAS offerings. Did we mention that set up, including configuring, will take you less than an hour since it all comes in one box and is so darn simple to use? So if you L-O-V-E what you’re hearing about Oracle’s Sun Z-F-S, learn more by watching the video below, and visiting any of our available resources . It Had to Be You, The OPN Communications Team

  Read the article

• After startup, display reverts to one desktop duplicated on both screens

  - by Skilldrick

  I have a Samsung R530 laptop. I'm actually running Linux Mint, which is based on Ubuntu (which is why I thought it would be OK to post this here). I'm now getting exactly the same problem on Ubuntu 10.10. I've got it setup with a secondary LCD monitor, and I've changed the display settings so the laptop screen and monitor are at optimal resolution, with the desktop shared between them. After startup though (typically around 10-30 seconds) the display reverts to 1024 x 768 on both screens, and the display is duplicated (i.e. both screens show the same thing). I think this is something to do with my video card, as I had the same problem when I was running Arch Linux. Any ideas? Edit: 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 09) 00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 09) 00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) 00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 03) 00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation ICH9M/M-E SATA AHCI Controller (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) 04:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller It seems it's Intel, not Nvidia. I have a current work around, which is to have a launcher to a script containing xrandr --output LVDS1 --mode 1366x768 --output HDMI1 --mode 1280x1024 --left-of LVDS1 on my desktop, and to run it after the displays revert, but it's not ideal.

  Read the article

• Upgrading Oracle Enterprise Manager: 12c to 12c Release 2

  - by jorge_neidisch

  1 - Download the OEM 12c R2. It can be downloaded here: http://www.oracle.com/technetwork/oem/grid-control/downloads/index.html  Note: it is a set of three huge zips. 2 - Unzip the archives 3 - Create a directory (as the oem-owner user) where the upgraded Middleware should be installed. For instance: $ mkdir /u01/app/oracle/Middleware12cR2 4 - Back up OMS (Middleware home and inventory), Management Repository and Software Library. http://docs.oracle.com/cd/E24628_01/doc.121/e24473/ha_backup_recover.htm#EMADM10740 5 - Ensure that the Management tables don't have snapshots:  SQL> select master , log_table from all_mview_logs where log_owner='<EM_REPOS_USER>If there are snapshots drop them:  SQL> Drop snapshot log on <master> 6 - Copy emkey  from existing OMS:  $ <OMS_HOME>/bin/emctl config emkey -copy_to_repos [-sysman_pwd <sysman_pwd>]To verify whether the emkey is copied, run the following command: $ <OMS_HOME>/bin/emctl status emkeyIf the emkey is copied, then you will see the following message:The EMKey  is configured properly, but is not secure.Secure the EMKey by running "emctl config emkey -remove_from_repos". 7 - Stop the OMS and the Agent $ <OMS_HOME>/bin/emctl stop oms $ <AGENT_HOME>/bin/emctl stop agent 8 - from the unzipped directory, run $ ./runInstaller 8a - Follow the wizard: Email / MOS; Software Updates: disable or leave empty. 8b - Follow the wizard:  Installation type: Upgrade -> One System Upgrade. 8c - Installation Details: Middleware home location: enter the directory created in step 3. 8d - Enter the DB Connections Details. Credentials for SYS and SYSMAN. 8e - Dialog comes: Stop the Job Gathering: click 'Yes'. 8f- Warning comes: click 'OK'. 8g - Select the plugins to deploy along with the upgrade process 8h- Extend Weblogic: enter the password (recommended, the same password for the SYSMAN user). A new directory will be created, recommended: /u01/app/oracle/Middleware12cR2/gc_inst 8i - Let the upgrade proceed by clicking 'Install'. 8j - Run the following script (as root) and finish the 'installation':  $ /u01/app/oracle/Middleware12R2/oms/allroot.sh 9 - Turn on the Agent:  $ <AGENT_HOME>/bin/emctl start agent  Note that the $AGENT_HOME might be located in the old Middleware directory:  $ /u01/app/oracle/Middleware/agent/agent_inst/bin/emctl start agent 10 - go to the EM UI. Select the WebLogic Target and choose the option "Refresh WebLogic Domain" from the menu. 11 - Update the Agents: Setup -> Manage Cloud Control -> Upgrade Agents -> Add (+) Note that the agents may take long to show up. ... and that's it! Or that should be it !

  Read the article

• Developing a Support Plan for Cloud Applications

  - by BuckWoody

  Last week I blogged about developing a High-Availability plan. The specifics of a given plan aren't as simple as "Step 1, then Step 2" because in a hybrid environment (which most of us have) the situation changes the requirements. There are those that look for simple "template" solutions, but unless you settle on a single vendor and a single way of doing things, that's not really viable. The same holds true for support. As I've mentioned before, I'm not fond of the term "cloud", and would rather use the tem "Distributed Computing". That being said, more people understand the former, so I'll just use that for now. What I mean by Distributed Computing is leveraging another system or setup to perform all or some of a computing function. If this definition holds true, then you're essentially creating a partnership with a vendor to run some of your IT - whether that be IaaS, PaaS or SaaS, or more often, a mix. In your on-premises systems, you're the first and sometimes only line of support. That changes when you bring in a Cloud vendor. For Windows Azure, we have plans for support that you can pay for if you like. http://www.windowsazure.com/en-us/support/plans/ You're not off the hook entirely, however. You still need to create a plan to support your users in their applications, especially for the parts you control. The last thing they want to hear is "That's vendor X's problem - you'll have to call them." I find that this is often the last thing the architects think about in a solution. It's fine to put off the support question prior to deployment, but I would hold off on calling it "production" until you have that plan in place. There are lots of examples, like this one: http://www.va-interactive.com/inbusiness/editorial/sales/ibt/customer.html some of which are technology-specific. Once again, this is an "it depends" kind of approach. While it would be nice if there was just something in a box we could buy, it just doesn't work that way in a hybrid system. You have to know your options and apply them appropriately.

  Read the article

• Developing a Support Plan for Cloud Applications

  - by BuckWoody

  Last week I blogged about developing a High-Availability plan. The specifics of a given plan aren't as simple as "Step 1, then Step 2" because in a hybrid environment (which most of us have) the situation changes the requirements. There are those that look for simple "template" solutions, but unless you settle on a single vendor and a single way of doing things, that's not really viable. The same holds true for support. As I've mentioned before, I'm not fond of the term "cloud", and would rather use the tem "Distributed Computing". That being said, more people understand the former, so I'll just use that for now. What I mean by Distributed Computing is leveraging another system or setup to perform all or some of a computing function. If this definition holds true, then you're essentially creating a partnership with a vendor to run some of your IT - whether that be IaaS, PaaS or SaaS, or more often, a mix. In your on-premises systems, you're the first and sometimes only line of support. That changes when you bring in a Cloud vendor. For Windows Azure, we have plans for support that you can pay for if you like. http://www.windowsazure.com/en-us/support/plans/ You're not off the hook entirely, however. You still need to create a plan to support your users in their applications, especially for the parts you control. The last thing they want to hear is "That's vendor X's problem - you'll have to call them." I find that this is often the last thing the architects think about in a solution. It's fine to put off the support question prior to deployment, but I would hold off on calling it "production" until you have that plan in place. There are lots of examples, like this one: http://www.va-interactive.com/inbusiness/editorial/sales/ibt/customer.html some of which are technology-specific. Once again, this is an "it depends" kind of approach. While it would be nice if there was just something in a box we could buy, it just doesn't work that way in a hybrid system. You have to know your options and apply them appropriately.

  Read the article

• Hierachies....from the Top Down

  - by Joe G

  I've been struggling with how to write on the topic of the importance of hierarchy design.  It's not so much that hierarchies haven't always been important, it's more of that with Fusion, the timing of when the hierarchies are designed should take a higher priority.    I will attempt to explain..... When I was implementing applications, back in the day, we had the list of detailed account values to enter with the obvious parent accounts. Then, after the setup was complete and things were functioning, the reporting phase started.  Users explained the elements that they want on the reports, what totals should be included, and how things should be compared.  Frequently, there was at least one calculation that became a nightmare either because it was based on very specific things that didn't relate to anything else or because it was "hardcoded" so that when something changed, someone need to "fix" the report. With Fusion, the process changes slightly.  You still want to enter all of the detailed accounts, but before you start adding parent values, you should investigate the reporting requirements from the top-down.  It's better to build hierarchies based on the reporting requirements than it is to build reports based on random hierarchies. Build reports based on hierarchies that resemble the reports themselves, and maintain the hierarchies without rework of the reports. For example, if you look at an income statement, you may have line items for Material Costs, Employee Costs, Travel & Entertainment, and Total Operating Expenses.  In your hierarchy, you have detail values that roll up to Material Costs, Employee Costs, and Travel & Entertainment which roll up to Total Operating Expenses. Balances are stored automatically in the cube for each of these.  When you define the report, you pick each of these members - no calculations required.  If a new detail value is added, you simply add it to the hierarchy, and there is no need to modify the report. I realize that there are always exceptions that require special handling, but I am confident that you will end up with much fewer exceptions if you make reporting a priority and design your hierarchies from the top-down.

  Read the article

• High-Powered Sites for low Cost

  - by HighAltitudeCoder

  Ahh, I am experiencing the intimidation of my very first post - visible by the whole world. Ok, here goes.   This first post is nothing exceptional.  It is simply a recommendation based (fittingly, I suppose) upon the job search you may be gearing up for.  I find myself in this very situation right now.  And, I will take my own recommendation after posting this entry. Job-Seekers: To the left you will notice two links under "Recommended Learning".  I have found these links to be invaluable when it comes to re-tooling, re-familiarizing, or otherwise resharping my skills when looking for that next job. Often, you will find job-postings with the text, usually posted after a laborious list of qualifications indicating the company's desire to hire candidates who know what they are doing: "...Looking for a candidate who can hit the ground running...".  The interesting thing about this post to me is I've encountered many individuals who, after speaking and working with them for some time, I've realized are perfectly capable of hitting the ground running - and FAST.  But what if they speed off in the wrong direction? The next time you spearhead a major task in your job, ask yourself: Am I headed in the wrong direction?  There are many ways to do this.  In fact, I've found in this new field there are more tempting ways to steer your project in the wrong direction than there are good ones.  I don't want to suggest that every one of my posts will fall into the "right direction" category, however I do think a healthy dose of introspection of the pros and cons will always be beneficial before you set off. That said, allow me to expound on the previously mentioned links. These web sites are invaluable.  They demonstrate the capabilities of existing as well as new and upcoming tools available in several IDE's.  I've viewed many tutorials in LearnVisualStudio.NET, and only one or two so far in TrainingSpot, however I've been delighted in their simplicity and straightforward approach to proper usage of the particular tool or concept being discussed.  They have not (so far in my experience) demonstrated ways in which to use the tools that become cumbersome, impractical, or error-prone. Each website has step-by-step videos that can be paused, replayed, and most importantly, they are done in real time.  As the author is typing, the viewer gets to experience the coding experience from a first-person perspective, including syntax errors, unexpected behaviors, IDE setup idiosyncracies, everything.  A subtle value I've gained from these videos is that a certain degree of confusion and introspection is normal when working with new tools and exploring new paths.  They (as well as your own experience) are not to be feared, but enjoyed.  I highly recommend them. Good work, guys!

  Read the article

• How to have an Arduino wait until it receives data over serial?

  - by SonicDH

  So I've wired up a little robot with a sound shield and some sensors. I'm trying to write a sketch that will let check the sensors. What I'd like for it to do is print out a little menu over serial, wait until the user sends a selection, jump to the function that matches their selection, then (once the function is done) jump back and print the menu again. Here's what I've written, but I'm not a that good of a coder, so it doesn't work. Where am I going wrong? #include <Servo.h> Servo steering; Servo throttle; int pos = 0; int val = 0; void setup(){   Serial.begin(9600);   throttle.write(90);   steering.write(90);   pinMode(A0, INPUT);   pinMode(7, INPUT);   char ch = 0; } void loop(){   Serial.println("Menu");   Serial.println("--------------------");   Serial.println("1. Motion Readout");   Serial.println("2. Distance Readout");   Serial.println("3. SD Directory Listing");   Serial.println("4. Sound Test");   Serial.println("5. Car Test");   Serial.println("--------------------");   Serial.println("Type the number and press enter");   while(char ch = 0){   ch = Serial.read();}   char ch;   switch(ch)   {     case '1':     motion();   }    ch = 0; } //menu over, lets get to work. void motion(){   Serial.println("Haha, it works!"); } I'm pretty sure a While loop is the right thing to do, but I'm probably implementing it wrong. Can anyone shed some light on this?

  Read the article

• Why doesn't Ubuntu detect my second hard drive?

  - by user93179

  I am new to Linux and to Ubuntu, I was wondering, I have two hard drives setup in SATA ports (non-raid, at least I don't think they are). I installed ubuntu unto the drives fresh without any previous versions or windows at all. However when I got the Ubuntu 12.04 LTS working, all I see is 1 x 120 gigabyte harddrive. Also, not sure if this is important or not, my hard drives are SSD. My computer specs are Asus P9Z77-V-LK Nvidia Geforce GTX 660 TI Intel i5 3570k 3.4 /proc/partitions shows: major minor #blocks name 8 0 117220824 sda 8 1 117219328 sda1 8 16 117220824 sdb 8 17 96256 sdb1 8 18 108780544 sdb2 8 19 8342528 sdb3 11 0 1048575 sr0 and ls -l /sys/block/ | grep -v /virtual/: lrwxrwxrwx 1 root root 0 Sep 27 17:26 sda - ../devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda lrwxrwxrwx 1 root root 0 Sep 27 17:26 sdb - ../devices/pci0000:00/0000:00:1f.2/host1/target1:0:0/1:0:0:0/block/sdb lrwxrwxrwx 1 root root 0 Sep 27 22:26 sdc - ../devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.1/1-1.1:1.0/host6/target6:0:0/6:0:0:0/block/sdc lrwxrwxrwx 1 root root 0 Sep 27 22:04 sr0 - ../devices/pci0000:00/0000:00:1f.2/host3/target3:0:0/3:0:0:0/block/sr0 sudo file -s /dev/sd*: /dev/sda: x86 boot sector; partition 1: ID=0x7, starthead 32, startsector 2048, 234438656 sectors, code offset 0xc0, OEM-ID " ?", Bytes/sector 190, sectors/cluster 124, reserved sectors 191, FATs 6, root entries 185, sectors 64514 (volumes 32 MB) , physical drive 0x7e, dos 32 MB) , FAT (32 bit), sectors/FAT 749, reserved3 0x800000, serial number 0x35361a2b, unlabeled /dev/sdb2: Linux rev 1.0 ext4 filesystem data, UUID=387761ac-5eba-4d0f-93ba-746a82fb541d (needs journal recovery) (extents) (large files) (huge files) /dev/sdb3: data /dev/sdc: x86 boot sector; partition 1: ID=0xc, active, starthead 0, startsector 8064, 30473088 sectors, code offset 0xc0 /dev/sdc1: x86 boot sector, code offset 0x58, OEM-ID "SYSLINUX", sectors/cluster 64, reserved sectors 944, Media descriptor 0xf8, heads 128, hidden sectors 8064, sectors 30473088 (volumes 32 MB) , FAT (32 bit), sectors/FAT 3720, Backup boot sector 8, serial number 0xf90c12e9, label: "KINGSTON " /dev/sda1: x86 boot sector, code offset 0x52, OEM-ID "NTFS ", sectors/cluster 8, reserved sectors 0, Media descriptor 0xf8, heads 255, hidden sectors 2048, dos 32 MB) , FAT (32 bit), sectors/FAT 749, reserved3 0x800000, serial number 0x35361a2b, unlabeled Any help would be greatly appreciated! Thanks Another thing I noticed is, when i use gparted to locate my drives, it seems that sda1 is my second drive that I am not detecting when I boot up and my ubuntu + FAT Boot files are installed in sdb1

  Read the article

• Send raw data to USB parallel port after upgrading to 11.10 oneiric

  - by zaphod

  I have a laser cutter connected via a generic USB to parallel adapter. The laser cutter speaks HPGL, as it happens, but since this is a laser cutter and not a plotter, I usually want to generate the HPGL myself, since I care about the ordering, speed, and direction of cuts and so on. In previous versions of Ubuntu, I was able to print to the cutter by copying an HPGL file directly to the corresponding USB "lp" device. For example: cp foo.plt /dev/usblp1 Well, I just upgraded to Ubuntu 11.10 oneiric, and I can't find any "lp" devices in /dev anymore. D'oh! What's the preferred way to send raw data to a parallel port in Ubuntu? I've tried System Settings Printing + Add, hoping that I might be able to associate my device with some kind of "raw printer" driver and print to it with a command like lp -d LaserCutter foo.plt But my USB to parallel adapter doesn't seem to show up in the list. What I do see are my HP Color LaserJet, two USB-to-serial adapters, "Enter URI", and "Network Printer". Meanwhile, over in /dev, I do see /dev/ttyUSB0 and /dev/ttyUSB1 devices for the 2 USB-to-serial adapters. I don't see anything obvious corresponding to the HP printer (which was /dev/usblp0 prior to the upgrade), except for generic USB stuff. For example, sudo find /dev | grep lp produces no output. I do seem to be able to print to the HP printer just fine, though. The printer setup GUI gives it a device URI starting with "hp:" which isn't much help for the parallel adapter. The CUPS administrator's guide makes it sound like I might need to feed it a device URI of the form parallel:/dev/SOMETHING, but of course if I had a /dev/SOMETHING I'd probably just go on writing to it directly. Here's what dmesg says after I disconnect and reconnect the device from the USB port: [ 924.722906] usb 1-1.1.4: USB disconnect, device number 7 [ 959.993002] usb 1-1.1.4: new full speed USB device number 8 using ehci_hcd And here's how it shows up in lsusb -v: Bus 001 Device 008: ID 1a86:7584 QinHeng Electronics CH340S Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 8 idVendor 0x1a86 QinHeng Electronics idProduct 0x7584 CH340S bcdDevice 2.52 iManufacturer 0 iProduct 2 USB2.0-Print iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 32 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0x80 (Bus Powered) MaxPower 96mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 7 Printer bInterfaceSubClass 1 Printer bInterfaceProtocol 2 Bidirectional iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0020 1x 32 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x02 EP 2 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0020 1x 32 bytes bInterval 0 Device Status: 0x0000 (Bus Powered)

  Read the article

• Developer career feeling like going back in time every new job [closed]

  - by komediant

  Is there a good category for this question? My background is bachelor in ICT and for a hobby I am programming already since I was around twelve I think. Started with QBasic, Pascal, C, Java et cetera. Currently I am working for about eight/nine years. Half academics/medical and half company world. A few years ago I started with frameworks and I began with Grails (underlying Spring/Hibernate), which was a heavenly job, very productive and no hassle. My previous job I developed in pure Spring/Hibernate Java, which was a bit more writing annotations and XML and no conventions like Grails. But still, I did like Spring/Hibernate a lot and the professional setup with a developmentstreet, versioning, Jenkins/Sonar, log4j and a good IDE like IntellIJ. It felt quite 'clear' and organised, although I knew Grails which felt a bit more productive. But...at my current job almost half the code is pure servlet, hard coded JDBC (connections handled by yourself), scriptlets in all JSP pages, no service layer, no versioning, no Maven, HTML in DAO-layer, JAR-hell, no hot swap deployment locally, every change you have to deploy and hope it works fine on the server. All local development needs ugly scriptlet tags to check which environment it is running. Et cetera. Now and then developers work over in the evening - I don't - and still lots of issues are not solved and new projects are waiting. I hear the developers complaining, but somehow they feel like what they have now is "advanced" or they are in a sort of comfore zone. The lead developer seems open for new things, but half of the times he says he can implement MVC-framework features himself instead of using what is already out there. So in short, I currently feel like I miss all the modern framework techniques and that the company is going so slow forward. I just work here for two months now. What I do now is also code some partially ugly stuff, but it goes in completely into my nature and I feel uncomfortable with it. Coding something takes long(er) than estimated and my manager complains about why it takes so long and I feel ashamed for myself needing so much time. Where I was used to just writing a query I now build up whole try catch methods. My manager knows my complaints and the developers do so too. There will come a meeting to line out plans for 2013 on technology and the issues I and the company are facing. I am not looking for another job yet, it's close to wehre I live and the economy is fragile. Does anyone else have had this kind of career, like feeling going backwards witch technology? And how did you cope with it?

  Read the article

• Raid superblock missing on single parition. Recovery needed!

  - by user171639

  Ok so I have a 2 TB raid 1 setup that has three partitions: sdc1: linux sdc2: swap sdc3: LVM for data However the LVM will no longer mount. So I thought that I would take the first drive, mount it in linux (ive done this b4), and reset the spare drive to copy the data. Normally I can mount a single drive for data recovery using: sudo su apt-get install mdadm lvm2 mdadm --assemble --scan modprobe dm-mod vgscan vgchange -ay c mount -o ro /dev/c/c /mnt Unfortunately, vgscan doesnot recognize the data partition. It appears as though the superblock on the first drive's data partition was erased while syncing with the second. So now I cannot mount that partition and the second drive is stuck in spare mode. Any ideas? Or a way to force mount the data partition just to copy the data? knoppix@Microknoppix:~$ sudo su root@Microknoppix:/home/knoppix# apt-get install mdadm lvm2 Reading package lists... Done Building dependency tree Reading state information... Done lvm2 is already the newest version. mdadm is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 551 not upgraded. root@Microknoppix:/home/knoppix# mdadm --assemble --scan mdadm: /dev/md/1 has been started with 1 drive (out of 2). mdadm: /dev/md/0 has been started with 1 drive (out of 2). root@Microknoppix:/home/knoppix# modprobe dm-mod root@Microknoppix:/home/knoppix# vgscan Reading all physical volumes. This may take a while... No volume groups found root@Microknoppix:/home/knoppix# cat /proc/mdstat Personalities : [raid1] md0 : active raid1 sdc1[2] 4193268 blocks super 1.2 [2/1] [U_] md1 : active raid1 sdc2[2] 524276 blocks super 1.2 [2/1] [U_] unused devices: <none> root@Microknoppix:/home/knoppix# mdadm -v --assemble --auto=yes /dev/md2 /dev/sdc3 mdadm: looking for devices for /dev/md2 mdadm: no recogniseable superblock on /dev/sdc3 mdadm: /dev/sdc3 has no superblock - assembly aborted root@Microknoppix:/home/knoppix# dumpe2fs /dev/md0 | grep -i superblock dumpe2fs 1.42.4 (12-Jun-2012) Primary superblock at 0, Group descriptors at 1-1 Backup superblock at 32768, Group descriptors at 32769-32769 Backup superblock at 98304, Group descriptors at 98305-98305 Backup superblock at 163840, Group descriptors at 163841-163841 Backup superblock at 229376, Group descriptors at 229377-229377 Backup superblock at 294912, Group descriptors at 294913-294913 Backup superblock at 819200, Group descriptors at 819201-819201 Backup superblock at 884736, Group descriptors at 884737-884737 root@Microknoppix:/home/knoppix# Notes: I can read the super block from the spare drive. I was gonna try and restore the superblock from one of the backups, but i dont know how or if this would work. I also heard creating a new array (mdadm --create) using the same parameters will not delete the data on the drive but i didnt want to risk it. Recommendations?

  Read the article

• HOW TO: Change Internet Expenses Cost Center Prompt

  - by rveliche

  The cost center segment on the General Information page in Oracle Internet Expenses derives its label from the Prompt entered on the KFF setup. Changing this is not possible with the simple personalization, the details below provide the instructions to change the Prompt. Create a custom class, I call it CustomHeaderKffCO.java in the package oracle.apps.ap.oie.entry.header.webui  (or any other). This class will have to extend from oracle.apps.ap.oie.entry.header.webui.HeaderKffCO. Add the following logic to your custom class. package oracle.apps.ap.oie.entry.header.webui; import oracle.apps.fnd.framework.webui.OAPageContext; import oracle.apps.fnd.framework.webui.beans.OAWebBean; import oracle.apps.fnd.framework.webui.beans.message.OAMessageLayoutBean; import oracle.apps.fnd.framework.webui.OAControllerImpl; public class CustomHeaderKffCO extends HeaderKffCO {   public void processRequest(OAPageContext pageContext, OAWebBean webBean)   {      super.processRequest(pageContext, webBean);     OAMessageLayoutBean layoutBean = (OAMessageLayoutBean) webBean.findChildRecursive("KffSEGMENT2MessageLayout");    if(layoutBean != null)   {     // You should use messages/lookups to avoid translation issues.     layoutBean.setLabel("Cost Center");   }   } } KffSEGMENT2MessageLayout is for illustration only, my Chart Of Accounts has SEGMENT2 as the cost center segment. Please change this to a segment being used eg.Segment6 should be KFFSEGMENT6MessageLayout Note that super.processRequest(pageContext, webBean); is a must and should always be the first statement. Once the class is compiled, copy the class to an appropriate directory, in my case I used $JAVA_TOP/oracle/apps/ap/oie/entry/header/webui. Navigate to the General Information page, click on "Personalize General Information Page".Click on Personalize icon next to Message Component Layout: (OIEGeneralInformationMsgCLayout)In the controller class section update the new controller at the appropriate levelIf the Link "Personalize General Information Page" is not visible on your instance, check your personalization profiles.

  Read the article

• Upgrading to 9.2 - Info You Can Use (part 2 - Get Hands On Experience)

  - by John Webb

  Our guest blogger, Rebekah Jackson, continues with a series of helpful hints on planning your upgrade to PeopleSoft 9.2. Get Hands-On Experience With a an Easy to Install Demo Image Once you have identified the features you believe can add value (see part 1 of this series here), we recommend that you use our Demo Images to quickly create a PeopleSoft environment where you can try out the new features. The Demo Images are virtual machines that run in VirtualBox.   They contain a fully functioning PeopleSoft environment, including the database, PeopleTools, and the application.  These images can be loaded onto nearly any sized machine that meets the specs outlined in the documentation, including a powerful desktop machine.     The image allows you to very quickly deploy a fully functioning PeopleSoft instance that you can use to explore new features and functions or run a conference room pilot. To take advantage these Demo Images: Go to the Demo Images Home Page (Doc id 1552548.1) on My Oracle Support. Use the " Demo Image Quick Start Guide" and additional documentation links on that page to download and install your desired Demo Image. New Demo Images are posted for each product area approximately every 10 weeks, available shortly after the corresponding patching image. When installed, use the Demo Image to explore the desired features and capabilities. Important Notes: - It is not required to use the Demo Images to evaluate features and functions – any 9.2 instance will support this. We recommend use of the Demo Images because the setup and configuration is dramatically faster than doing a traditional PeopleSoft install. - For those looking to explore new features and capabilities on PeopleSoft 9.1 releases, we have provided virtual machine images using the Oracle Virtual Machine technology. Details and links are available in Oracle’s PeopleSoft Virtualization Products page (Doc id 1538142.1). /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Calibri","sans-serif"; mso-bidi-font-family:"Times New Roman";}

  Read the article

• Setting the SlideShowExtender's Index

  - by Bunch

  The AJAX SlideShowExtender is pretty useful. It does what it says and works without much fuss. There was one trick I needed it to perform that I could not find natively within the control. That was to set the slide’s current index. With a little JavaScript however I could make the control do what I wanted. The example below assumes a few things. First you already have a SlideShowExtender setup and working (or see this post). Second this SlideShowExtender is on a page all by itself so the index to set the slide to is passed in the URL. The scenario I had was this SSE was showing full images, the index was passed from another page that had a SSE showing thumbnails. JavaScript in <head> <script type="text/javascript">      function pageLoad() {          var slider = $find("sse");          var photoIndex = GetQuerystring('Index', 0);          slider._currentIndex = photoIndex - 1;          slider._slides = '';          slider.setCurrentImage();      }      function GetQuerystring(key, default_) {          if (default_ == null) default_ = '0';          key = key.replace(/[\[]/, "\\\[").replace(/[\]]/, "\\\]");          var regex = new RegExp("[\\?&]" + key + "=([^&#]*)");          var qs = regex.exec(window.location.href);          if (qs == null)              return default_;          else              return qs[1];      } </script> The GetQuerystring function is what grabs the Index value I pass from the page with the thumbnails. It does not have anything else to do with setting the slide index. The code in the pageLoad function sets the index on the slide_currentIndex line. The slider.setCurrentImage() line does pretty much what it says. I added the slider._slider = ‘’ to avoid an error (not a show stopper just a bit annoying). Control in <body> <cc1:SlideShowExtender ID="ssePhotos" runat="server" TargetControlID="imgFull" AutoPlay="false"          PreviousButtonID="btnPrev" NextButtonID="btnNext" SlideShowServicePath="PlacePhotos.asmx"           SlideShowServiceMethod="GetPlaceFullPhotos" BehaviorID="sse" ImageDescriptionLabelID="lblPictureDescription"> </cc1:SlideShowExtender> The main property to set with the SSE is the BehaviorID. This is what a JavaScript function can use to find the control rather than the control’s ID value. Technorati Tags: AJAX,ASP.Net,JavaScript

  Read the article

< Previous Page | 517 518 519 520 521 522 523 524 525 526 527 528  | Next Page >