Search Results

Search found 15150 results on 606 pages for 'azure services'.

Page 524/606 | < Previous Page | 520 521 522 523 524 525 526 527 528 529 530 531  | Next Page >

  • Would an invalid certificate cause an 0x8004010F sync error?

    - by hydroparadise
    We just migrated from Exchange 2003 to 2007 which was a combo primary AD/DNS server and it has not gone smoothly. We are now down to getting a new certificate (a bureaucratic process thats out of my hands) and users getting the 0x8004010F sync issue. We are only using Outlook 2007 as our email client and the sync error appears exactly as so: 9:21:44 Synchronizer Version 12.0.6562 9:21:44 Synchronizing Mailbox '<User>' 9:21:44 Done 9:21:44 Microsoft Exchange offline address book 9:21:44 0X8004010F Now, I have read a number of technet articles on this issue anywhere from adding an A record in the DNS for autodiscover.domain.com to syncing the old OAD to the new OAD. In otherwords, theres lots of thing to try, but trial and error at this point might be hazardous to ther server's health and I am trying to narrow down the list of things to try. What has me thinking that the sync error could be related to the certificate is an event error message that says the following: Microsoft Exchange could not find a certificate that contains the domain name mail.ccufl.org in the personal store on the local computer. Therefore, it is unable to support the STARTTLS SMTP verb for the connector Internet Mail with a FQDN parameter of mail.ccufl.org. If the connector's FQDN is not specified, the computer's FQDN is used. Verify the connector configuration and the installed certificates to make sure that there is a certificate with a domain name for that FQDN. If this certificate exists, run Enable-ExchangeCertificate -Services SMTP to make sure that the Microsoft Exchange Transport service has access to the certificate key. I am not fully clear on how the Exchange Transport Service is related to Syncronization, but my hunch is that it probably not related to there not being a valid certificate. So to recap, would an invalid certificate cause an 0x8004010F sync error?

    Read the article

  • Error setting up Data Protection Manager 2010 Agents / Network "Unauthenticated" in network settings

    - by Bowsa
    I'm not sure if the two are connected but i suspect they are. Basically I'm tring to setup Data Protection Manager 2010 on a fresh install of Server 2008 R2 in a SBS 2003 domain. Everything went fine until trying to install agents across the network. Upon clicking add, i get the following error message: Unable to connect to the Active Directory Domain Services Database. Make sure that the DPM server is a member of a domain and that the controller is running. Also verify that there is network connectivity between the DPM server and the domain controller. ID: 7 As usual (worryingly) the MSDN support for 2010 products is nearly non existant, clicking the error ID simply gives a page not found error. So after 2 days of Googling and trying various fixes (DNS settings, adding permissions to AD objects, rejoining the domain and many more) I thought I'd ask here in the hope that someone out there may have had this issue before. Any help greatly appreciated! Some further info: Firewalls are disabled on the Server 2008, SBS, and client machines. Manually installing and adding the client in also fails, as the DPM server tries to contact the DC first. Edit: I tried creating a new protection group instead, and it gives a different error upon adding the machines: Following machines are not found in AD: COMPUTERNAME.COMPANYNAME.LOCAL Is there a certain directory structure it follows in AD?

    Read the article

  • vyatta Server Reboots by itself

    - by Fernando
    I have an issue regarding some hardware, maybe you can help me. First, I set up a Supermicro Superserver SYS-5016I-NTF with a Intel Xeon X3470 and 4 GB of Ram with a Hotlava Card Tambora 64G4 with Intel Chipset 82599EB and 4x10G SPF+ ports. Installed Vyatta community edition 6.3. I used it as router making BGP connections with 2 operators. No load at all, temp ranges normal. But the issue is that it reboots by itself in a ramdom way. Not very often, once every few days. But it is unacceptable for production purposes. So I try to test on different hardware, and installed Vyatta community edition 6.3 on a Dell PowerEdge 2950, with Xeon(R) E5345 @ 2.33GHz and 4 GB of Ram. Same Vyatta configuration as Supermicro Server. With same hotlava Card model ( I bought two of them ) Well I have reboots with this equipment as well. Same frecuency as above. I have checked syslog no strange logs until boot process starts to be logged. So it seems server reboot suddenly. I have installed latest driver for the chipset of the Hotlava card. Servers are placed in a datacenter with UPS So finally two things in common in both servers: Hotlava Card. Someone with issues with this card, or the chipset?? Could be it this card?? Vyatta 6.3 community edition. I don't thing is the problem. Is a regular Debian with packages to glue together different services. Or maybe is something I am missing. Andy ideas, suggestions?? Thank you very much... Fernando

    Read the article

  • Hosting django backend for iPhone / Android app

    - by Ashok Fernandez
    I am looking to make an iPhone / Android app for my university using the Appcelerator Titanium framework. The app will rely heavily on a server backend which will pull information from other sites, figuring out what is relevant to the user then deliver the content. Some of the information is individual to the user (calendar data), other bits are updates frequently but are shared (bus timetables) and others are static and the same for everyone (magazine articles). I was going to use django as I am fairly proficent in python so I thought it would save time. My question is, which hosting services do you recommend to host the server backend? I am expecting about 9000 people to use the app with very random spikes in traffic, but unfortunately I have very little to go on at this stage. I have heard a lot about Webfaction, is it suitable for something like this or am I likely to need something bigger? I don't really want to fork out for a VPS at this stage. What about Amazons EC2? Would that be more suitable than Webfaction? Sorry for the fairly open ended question, Im sort of new to this so I open to all suggestions.

    Read the article

  • My linux server "Number of processes created" and "Context switches" are growing incredibly fast

    - by Jorge Fuentes González
    I have a strange behaviour in my server :-/. Is a OpenVZ VPS (I think is OpenVZ, because /proc/user_beancounters exists and df -h returns /dev/simfs drive. Also ifconfig returns venet0). When I do cat /proc/stat, I can see how each second about 50-100 processes are created and happens about 800k-1200k context switches! All that info is with the server completely idle, no traffic nor programs running. Top shows 0 load average and 100% idle CPU. I've closed all non-needed services (httpd, mysqld, sendmail, nagios, named...) and the problem still happens. I do ps -ALf each second too and I don't see any changes, only a new ps process is created each time and the PID is just the same as before + 1, so new processes are not created, so I thought that process growing in cat /proc/stat must be threads (Yes, seems that processes in /proc/stat counts threads creation too as this states: http://webcache.googleusercontent.com/search?q=cache:8NLgzKEzHQQJ:www.linuxhowtos.org/System/procstat.htm&hl=es&tbo=d&gl=es&strip=1). I've changed to /proc dir and done cat [PID]\status with all PIDs listed with ls (Including kernel ones) and in any process voluntary_ctxt_switches nor nonvoluntary_ctxt_switches are growing at the same speed as cat /proc/stat does (just a few tens/second), Threads keeps the same also. I've done strace -p PID to all process too so I can see if any process is crating threads or something but the only process that has a bit of movement is ssh and that movement is read/write operations because of the data is sending to my terminal. After that, I've done vmstat -s and saw that forks is growing at the same speed processes in /proc/stat does. As http://linux.die.net/man/2/fork says, each fork() creates a new PID but my server PID is not growing! The last thing I can think of is that all process data that proc/stat and vmstat -s show is shared with all the other VPS stored in the same machine, but I don't know if that is correct... If someone can throw some light on this I would be really grateful.

    Read the article

  • Installing xampp on system that already have mysql

    - by Charith
    I'm rather new to PHP and xampp. I have a computer that has installed MySQL server and MySQL workbench as I was working with Java and NetBeans. Now I want to use my computer for developing PHP and other web stuff too. I installed xampp successfully. But when I'm trying to access phpMyAdmin, it gives me an error saying mysql server rejected its connection Actually I tried stopping my current MySQL service and installing it again. However xampp have a its own mysql server in its installation path too. I tried configuring config.inc.php to use my existing installation of MySQL which is on a separate path. But I failed. Can anyone please instruct me how to configure this xampp to use my existing MySQL server to do everything and ignore the installed one with itself? I don't want two MySQL services to run on my system and clash in future. I'll be glad if anyone can explain to me what is best to use when you're developing Java, PHP, C and all the stuff on the same machine. P.S.: I have been given a password for my existing MySQL sever (user = root) as we do it usually when installing MySQL alone.

    Read the article

  • Managing per-user rc.d init scripts

    - by Steve Schnepp
    I want to delegate SysV init scripts to each user. Like the SysV init, each item in ${HOME}/rc.d starting with S will be launched on server start-up with the start argument. The same for the server shut-down with the one starting with K and with the stop argument. I thought about scripting it myself, but maybe there is already some kind of implementation out there1. In summary it would be a script in /etc/init.d/ that iterates through all the users and launches runparts as the user on the relevant scripts. The platform here is a Linux (Debian flavour), but I think the solution would be quite portable among various Unix-like platforms. Update: The point here is for users to be able to create their own init scripts that should be launch on their behalf when the system boots up. As Dan Carley pointed out, the services won't be able to access any system asset (priviledged ports, system logs, ...). 1. This way I don't have to think that much about all the subtle security implications such as script timeouts for example...

    Read the article

  • master-slave datastore replication, automatic failover, and wackamole

    - by z8000
    I have 2 dedicated servers provisioned for my next project's datastores. The datastores are configured for master-slave replication. There's no inherent automatic failover but I of course want this. That is, I'd love for access to the master datastore to always just work without having to configure a client library to detect when a master is down and failover to the slave. I've seen Wackamole which is based on the Spread Toolkit. You provide Wackamole with a set of IPs and a bunch of nodes, and regardless of the up/down state of any of the nodes, those IPs will stay available/up. Wackamole detects when a node goes down and ARPs the IP(s) that were up on the now-down node. It's pretty neat actually. So, my thought was to use Wackamole to keep the 2 virtual private IPs available/up. Clients would then just always use the same private IP to access the master datastore and the same but distinct IP for the slave datastore, even if those IPs were hosted on the same node. My datastore servers are accessed over a private network. I am unsure if this messes with Wackamole though. Is this lunacy? How do you generally handle automatic failover of private services like a datastore. FWIW, it shouldn't matter but the datastore is Redis. I don't want to hear "use mySQL" please :) Thanks.

    Read the article

  • Can't Start SQL Server 2005 Agent - Start/Stop Are Not Enabled

    - by DaveB
    We have a brand new install of SQL Server 2005 on a Windows 2008 Server. When using the SQL Server Management Studio (2005 or 2008) from my Windows XP Professional workstation, if I right click on the SQL Server Agent, I get the context menu but the Start and Stop options are not enabled(grayed out). I am using Windows authentication, I am a member of the SysAdmin and Public SQL Server roles. Also, when right clicking on Maintenance Plans and selecting New Maintenance Plan, nothing happens. I was able to create a maintenance plan with the wizard but now am unable to execute it because SQL Server Agent isn't running? From what I was told by an admin who had access to the server, he was able to login to the box using the domain administrator account and start the SQL Server Agent service from the services applet or from the local instance of SQL Server 2005 Management Studio. Even after he started the service, it still didn't appear to be running from my workstation view through the management studio. What do I need to change to allow me to administer the agent and maintenance plans from my workstation? If I wasn't clear about anything, feel free to ask for clarification.

    Read the article

  • How does one make sure or even guarantee server time are sync correctly between dozens of servers across multiple datacenter on different location?

    - by forestclown
    Currently our web applications contain a logic to check if the data sent to the web server is expired or not by comparing the timestamp of the data with the date/time of the server. Everything goes will, until some dude from data center accidentally modify one of the web server date/time and causes some disruptions in our web services. My managers are of course not happy with this, and said we shouldn't use timestamp to check expiry in the first place...anyway.... Network Time Protocol is implemented, because of data centers are spread across different continents so we have one NTP server in each data center. The servers within the data center will have cron jobs to check against the time with their NTP server from the same data center. If time is out of sync it will auto update the server date/time. But then with our managers not happy with it, and think it could still easily causes the same problem. e.g. what if someone accidentally modify the NTP date/time? what if all the NTP servers are out of sync with each other? which NTP servers we can really trust? and blah blah.. So my questions are: What are the current practice to sync date/time between servers across multiple data centers or locations? How does one manages time stamp between web apps? e.g. Server A send data (contain timestamp of Server A) to Server B (compare timestamp between Server B and the timestamp from the data to see if it has expired or not. This is to avoid HTTP replay) Should we really not use timestamp check? Thanks & Best Regards

    Read the article

  • few basic questions on webhosting (namservers & dns records)

    - by claws
    I bought a domain name on name.com & I want to use free webhosting on 110mb.com By default name.com integrates services of Google apps. Name server entries are ns1.name.com ns2.name.com ns3.name.com ns4.name.com When I registered on 110mb.com it gave me two addresses ns1.110mb.com ns2.110mb.com This is where I'm lost. The concept is that "Domain name should point to an address of the server where the website is hosted" right? Then why are these 4 entires by default. How exactly is it working? should I remove these 4 and then add 110mb.com servers or just append 110mb.com server addresses to name.com ones. I would like to use google apps. If I change these name server addresses would that remove google apps? I especially want to use email service of google. And I really don't understand what is CNAME, MX, or something something. I want to learn about these stuff & how it exactly works. When I search for webhost tutorial. I'm unable to find any fruitful results.

    Read the article

  • Nginx + PHP-FPM Timeouts, almost zero load consumption?

    - by javipas
    I've got a server running on a Linode with Ubuntu 10.04 LTS, Nginx 0.7.65, MySQL 5.1.41 and PHP 5.3.2 with PHP-FPM. There is a WordPress blog on it, updated to WordPress 3.2.1 recently. I have made no changes to the server (except updating WordPress) and while it was running fine, a couple of days ago I started having downtimes. I tried to solve the problem, and checking the error_log I saw many timeouts and messages that seemed to be related to timeouts. The server is currently logging this kind of errors: 2011/07/14 10:37:35 [warn] 2539#0: *104 an upstream response is buffered to a temporary file /var/lib/nginx/fastcgi/2/00/0000000002 while reading upstream, client: 217.12.16.51, server: www.mydomain.com, request: "GET /page/2/ HTTP/1.0", upstream: "fastcgi://127.0.0.1:9000", host: "www.mydomain.com", referrer: "http://www.mydomain.com/" 2011/07/14 10:40:24 [error] 2539#0: *231 upstream timed out (110: Connection timed out) while reading response header from upstream, client: 46.24.245.181, server: www.mydomain.com, request: "GET / HTTP/1.1", upstream: "fastcgi://127.0.0.1:9000", host: "www.mydomain.com", referrer: "http://www.google.es/search?sourceid=chrome&ie=UTF-8&q=mydomain" and even saw this previous serverfault discussion with a possible solution: to edit /etc/php/etc/php-fpm.conf and change request_terminate_timeout=30s instead of ;request_terminate_timeout= 0 The server worked for some hours, and then broke again. I edited the file again to leave it as it was, and restarted again php-fpm (service php-fpm restart) but no luck: the server worked for a few minutes and back to the problem over and over. The strange thing is, although the services are running, htop shows there is no CPU load (see image) and I really don't know how to solve the problem. The config files are on pastebin The php-fpm.conf file is here The /etc/nginx/nginx.conf is here The /etc/nginx/sites-available/www.mydomain.com is here Please help :(

    Read the article

  • Configure IIS Web Site for alternate Port and receive Access Permission error

    - by Andrew J. Brehm
    When I configure IIS to run a Web site on Port 1414, I get the following error: --------------------------- Internet Information Services (IIS) Manager --------------------------- The process cannot access the file because it is being used by another process. (Exception from HRESULT: 0x80070020) However, as according to netstat the port is not in use. Completely aside from IIS, I wrote a test program (just to open the port and test it): TcpListener tcpListener; tcpListener = new TcpListener(IPAddress.Any, port); try { tcpListener.Start(); Console.WriteLine("Press \"q\" key to quit."); ConsoleKeyInfo key; do { key = Console.ReadKey(); } while (key.KeyChar != 'q'); } catch (Exception ex) { Console.WriteLine(ex.Message); } tcpListener.Stop(); The result was an exception and the following ex.Message: An attempt was made to access a socket in a way forbidden by its access permissions The port was available but its "access permissions" are not allowing me access. This remains after several restarts. The port is not reserved or in use as far as I know and while IIS says it is in use, netstat and my test program say it is not and my test program receives the error that I am not allowed to access the port. The test program ran elevated. The IIS Site is running MQSeries, but the MQ listener also cannot start on port 1414 because of this issue. A quick search of my registry found nothing interesting for port 1414. What are socket access permissions and how can I correct mine to allow access?

    Read the article

  • Configure tomcat behind loadbalancer to respond on HTTP and HTTPS

    - by user253530
    I have 2 tomcat machines behind a load balancer on Amazon EC2. Until now The load balancer was configured to respond only on https. So in order to access our services you would go to https://url. Tomcat was configured to listen on 8080 but the connector had additional params that would tell tomcat that it is behind a proxy and that it should respond on HTTPS 443. The connector looks like this: <Connector scheme="https" secure="true" proxyPort="443" proxyHost="my.domain.name" port="8080" protocol="HTTP/1.1" connectionTimeout="20000" redirectPort="8443" useBodyEncodingForURI="true" URIEncoding="UTF-8" /> What i would like to do is to open port 80 on the load balancer and basically allow traffic on HTTP and HTTPS. I've configured the load balancer to redirect all HTTP traffic to the tomcat machines on port 8088. I was thinking that i could define a new connector so that all HTTPS traffic goes to 8080 and HTTP to 8088. Unfortunately i did not succeed. Here is my connector <Connector port="8088" protocol="HTTP/1.1" connectionTimeout="20000" redirectPort="8443" useBodyEncodingForURI="true" URIEncoding="UTF-8" /> Am I missing something? Thanks

    Read the article

  • Joining Samba to Active Directory with local user authentication

    - by Ansel Pol
    I apologise that this is somewhat incoherent, but hopefully someone will be able to make enough sense of this to understand what I'm trying to achieve and provide pointers. I have a machine with two network interfaces connected to two different networks (one of which it's providing several other services for, such as DNS), running two separate instances of Samba, one bound to each interface. One of the instances is just a workgroup-style setup using share-level authentication, which is all working fine. The problem is that I'm looking to join the other instance to an MS Active Directory domain (provided by MS Windows Small Business Server 2003) to enable a subset of the domain users to access the shares from Windows machines on the other network. The users who need access from the domain environment have accounts (whose names are all-lowercase versions of their domain usernames) on the machine running Samba, but I'm not sure about how to map the UIDs and everything I've read concerns authenticating accounts on that machine against either AD or another LDAP server. To clarify: I only want the credentials for AD users accessing the non-workgroup Samba instance to be authenticated against AD, not the accounts on the machine running Samba. I hope this is sufficiently clear. EDIT: In addition to being able to access the Samba shares from AD, I do also need to be able to access a share on the domain from the machine running Samba but would still like everything non-Samba-related to authenticate locally.

    Read the article

  • Sonicwall NSA 240, Configured for LAN and DMZ, X0 and X2 on same switch - ping issues

    - by Klaptrap
    Our Sonicwall vendor supplied and networked the NSA240 when we required a DMZ in our infrastructure. This was configured and appeared correct although VPN users periodically dropped DNS and Terminal Services. The vendor could not resolve and so the call was escalated to Sonicwall. The Sonicwall support engineer took a look and concluded that the X0 (LAN) and X2 (DMZ) intefaces were cabled to the same switch and so this is the issue. What he observed is a ping request to the LAN Domain Controller, from a connected VPN user, is forwarded (x0) from the VPN client IP to the DC IP but the ping response from the DC IP to the VPN client IP is on X2, a copy of the log is detailed below:- 02/02/2011 10:47:49.272 X1*(hc) X0 192.168.1.245 192.168.1.8 IP ICMP -- FORWARDED 02/02/2011 10:47:49.272 -- X0* 192.168.1.245 192.168.1.8 IP ICMP -- FORWARDED 02/02/2011 10:47:49.272 X2*(i) -- 192.168.1.8 192.168.1.245 IP ICMP -- Received X0 - LAN X1 - WAN X2 - DMZ The Sonicwall engineer concluded that we either need a seperate switch for X2 or we use a VLAN switch for both. I am the companies software engineer and we have yet to have heard back from the vendor, so I am lost at sea at the moment. Do we need to buy this additional equipment or is there another configuration on the NSA240 we can use?

    Read the article

  • Windows 2008 server smart card security module problem

    - by chris13work
    Hi, I've got a smart card reader and a server application using it as a security module. If I run it under DOS prompt, everything is fine. The server is running and clients can connect to it. I tried to install the server as window service and start it. The server starts but always gives back authentication error because it cannot call the smart card to do encryption. Then I tried to start it with task scheduler and set the trigger factor as "on startup". The server starts also but still cannot access the smart card reader. Then I tried remote desktop to the machine and run the server application under DOS prompt. Same error is returned. The situation is that the smart card reader only works under active console desktop environment. In the server application, WINSCARD API is used to access the smart card reader. Any suggestion so that we can access the smart card reader in running services? OS: Windows Server 2008 Smart Card Driver: Windows USB smart card Reader Smart Card API: WINSCARD

    Read the article

  • Windows 2008 server smart card security module problem

    - by chris13work
    Hi, I've got a smart card reader and a server application using it as a security module. If I run it under DOS prompt, everything is fine. The server is running and clients can connect to it. I tried to install the server as window service and start it. The server starts but always gives back authentication error because it cannot call the smart card to do encryption. Then I tried to start it with task scheduler and set the trigger factor as "on startup". The server starts also but still cannot access the smart card reader. Then I tried remote desktop to the machine and run the server application under DOS prompt. Same error is returned. The situation is that the smart card reader only works under active console desktop environment. In the server application, WINSCARD API is used to access the smart card reader. Any suggestion so that we can access the smart card reader in running services? OS: Windows Server 2008 Smart Card Driver: Windows USB smart card Reader Smart Card API: WINSCARD

    Read the article

  • Recommendations for handling Directory Harvesting spam on Exchange 2003

    - by Aaron Alton
    Our Exchange server is getting slammed with anywhere between 450,000 and 700,000 spam messages per day. We receive about 1700 legitimate messages in the same time frame. Roughly 75% of the spam is directory harvesting. We currently have GFI MailEssentials installed. To it's credit, it's doing a very good job, but the sheer volume of spam that we're receiving, and the number of connections that our exchange server is making is preventing legitimate email from being delivered in a timely manner. GFI is set up to check for directory harvesting at the SMTP level, which I presume intercepts the mail before it hits the Exchange services , or goes through SMSE. This "module" is ordered at the top of the list, so (hopefully) dealing with the harvesting is consuming a minimum amount of server resources and bandwidth. My question is, is there anything I can do to prevent our Exchange server's connection pool from being eaten up by these spam hosts? We had to limit the number of concurrent connections being made by Exchange, because it was consuming all of our bandwidth. Thanks, in advance.

    Read the article

  • Wireless router that supports Bonjour between wire- and wireless- connected machines

    - by cefstat
    At home I have an ADSL modem that I use also as router. For the record, it is a DavoLink DV-2020 provided by Tele2 in the Netherlands. It turns out that if a computer is connected with a cable to the router and another computer is connected wirelessly, then they cannot see each other's services that are advertised through Bonjour (Apple's service discovery protocol, an implementation of Zeroconf). The combinations wired/wired and wireless/wireless work fine. This means that somehow wire- and wireless- connected machines are on different physical networks although their IPs are in the same range (192.168.1.*). The modem in question doesn't provide many options that I could play with. So, I was thinking of buying a second router to connect to the modem, and then connect all my machines to this second router. The problem is that I am afraid that I will have again the same problem. I am looking for suggestions on routers that offer the functionality I want (Bonjour between wired and wireless connections). I suppose that one solution would be Apple's Airport Extreme Base Station but at 160€ it is ridiculously expensive. Any other options out there? And why is it so difficult to find in the technical characteristics if wired and wireless connections are on the same physical network?

    Read the article

  • Failing Windows Updates with Error Code 800719e4

    - by Kev
    On a number of Vista machines I have now come across the same error - when installing updates everything works fine, until it after it reboots and the rolls back during step 3. On all occasions (where a simple retry hasn't worked) the error code has been 800719e4. On my own laptop I have so far tried the following:- Installed the updates one by one manually - I started on the smallest and one by one have worked towards the largest one which has left me with "Security Update for Windows (KB2286198)" that refuses to install. Renamed all the files in "C:\Windows\Logs\CBS" to "xxx.old" where xxx was the original name with windows update turned off - no change Renamed all the folders in "C:\Windows\SoftwareDistribution" in the same manner - no change Attempted to install it manually "Windows6.0-KB2286198-x86.msu" - no change Tried to un-install IE8 - doesn't work, rolls back at the end (Installing the IE9 Beta when it launched was what alerted me to the issue on this laptop) Ran a "Fix It" thing from the Microsoft Website - no help (Can't find the link now). Tried to recover from the disk - but alas my laptop only has a recovery partition (and was unservice packed original). Ran with nothing running on startup, and only MS services - again no change. Google is being useless with a load of posts trying to get me to call a telephone number with letters in (presumably an American number) The error code appears to mean error log full but no one has any idea which log! The WinUpdate log does indicate the following is the error point though :- 2010-10-23 13:54:48:230 1240 738 Handler WARNING: Got extended error: "POQ Operation SetKeyValue OperationData \Registry\machine\Schema\wcm://Microsoft-Windows-shell32?version=6.0.6002.18287&language=neutral&processorArchitecture=x86&publicKeyToken=31bf3856ad364e35&versionScope=nonSxS&scope=allUsers\metadata\elements\HKEY_CLASSES_ROOT_lnkfile_shellex_DropHandler_defaultValue, @default, , ewAwADAAMAAyADEANAAwADEALQAwADAAMAAwAC0AMAAwADAAMAAtAEMAMAAwADAALQAwADAAMAAwADAAMAAwADAAMAAwADQANgB9AAAA" Has anyone any idea how to fix this once and for all - reinstalling laptop after laptop from scratch is mildly annoying at work where Office and Firefox are the only extras, but even more annoying at home - I don't fancy going through the palaver of reinstalling everything yet again.

    Read the article

  • Can't get rsync over sftp to work

    - by Patrik
    I'm trying to set up a backup system from an Ubuntu server to a Synology NAS (DS413j) using rsync and sftp. I have created a user for this that we can call ubuntu-backup. I have a directory in ubuntu-backup home directory called www where the backup will be saved. I have enabled Network Backup in DSM The user ubuntu-backup has full access to it's home directory Here is my rsync config file on the Synology NAS: #motd file = /etc/rsyncd.motd #log file = /var/log/rsyncd.log pid file = /var/run/rsyncd.pid lock file = /var/run/rsync.lock use chroot = no [NetBackup] path = /var/services/NetBackup comment = Network Backup Share uid = root gid = root read only = no list = yes charset = utf-8 auth users = root secrets file = /etc/rsyncd.secrets [ubuntu-backup] path = /volume1/homes/ubuntu-backup/www comment = Ubuntu Backup uid = ubuntu-backup gid = users read only = false auth users = ubuntu-backup secrets file = /etc/rsyncd.secrets The permissions on /volume1/homes/ubuntu-backup/www is ubuntu-backup:users 777 Here is the command i'm running. rsync -aHvhiPb /var/www/ [email protected]:./ The result: sending incremental file list ERROR: module is read only rsync error: syntax or usage error (code 1) at main.c(1034) [Receiver=3.0.9] rsync: connection unexpectedly closed (9 bytes received so far) [sender] rsync error: error in rsync protocol data stream (code 12) at io.c(605) [sender=3.0.9] If I'm running this: rsync -aHvhiPb /var/www/ [email protected] It looks like its sending files. No errors. But I cant find anything on the NAS.

    Read the article

  • WebDav System Error 67 in Windows XP

    - by Nixphoe
    Issue: I'm having issues getting WebDav to work in the command line on Windows XP, both Service Pack 2 and Service Pack 3. C:\>net use z: https://mywebsite.com/software/ System error 67 has occurred. The network name cannot be found. I have tested this with two webdav server. Both Ubuntu Apache and I Windows Server 2003 IIS. Both get the same result. Things That Haven't Worked: I've installed the following Microsoft KB on my XP machines with no avail. I've also found the following reg key: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\WebClient\Parameters UseBasicAuth REG_DWORD 1 I try the following when trying to use a few work around I've dug up on the web, all producing the same result. net use z: https://mywebsite.com/software net use z: https://mywebsite.com/software# net use z: https://mywebsite.com/software/ net use z: https://mywebsite.com/software/# I've also tried all the above combinations adding a user into it /user:user and /user:user@domain. I've also tried using http:// rather than https://. I've tried "\\server.com@ssl:443\folder" I've gone over networking related issues as @WesleyDavid had pointed out. Things that do work: I can connect to the webdav folder via the URL and with mapping in Network Place, with XP. But the command line doesn't work (I need a drive letter). Windows 7 works perfectly with the same command. My Delemma: I need this to work with a drive letter. What else can I try to get this working?

    Read the article

  • Hosting a server for websites, ftp and random use at home?

    - by Zolomon
    I'm wondering what's the best option for me if I want to move all my hosted websites (from a hosting company) to a server at my own home? Basically, the needs I have are: be able to host websites using PHP/ASP.NET (haven't really decided yet - both would be preferred!) enable FTP so I can create accounts for my family members to access the server for file handling SSH SSL - for secure connections (this is something you have to buy/apply for per domain, not sure if there are any server side settings that have to be made) be able to stream video remote desktop host home-brew applications that can run as services use either MySQl/SQLite/SQL for relational database storage What should I think of before I buy a server? What hardware will I need, what will limit my server? I basically want to learn networking better as I'm a software and web developer but haven't had the resources to acquire any serious toys until now. At the time of writing, most of my websites have 60 visits/day so I don't suspect them to be very demanding. Is there something I haven't thought of that I should have? What OS would you suggest I run? FreeBSD vs Windows Server vs ?

    Read the article

  • Configure one IIS site to handle two separate SSL certificates using external Load Balancing or SSL Acceleration Servers

    - by bmccleary
    I have one web application on our server that needs to be referenced by two different domain names, both of which have their own SSL certificates. The application is exactly the same for both domains, but we have to keep the two domain names for legal reasons. The problem is that, since both domains need to have their own SSL certificate, that inside of our IIS 7.5 configuration we have to have two separate IIS applications (both pointing to the same physical location) with their own unique IP address and SSL certificate installed. Now, I know that, due to the nature of SSL communications, that this is by design and that you can't assign more than one SSL certificate per IP address and domain name. My question is… is there any way around this limitation and keep one web application in IIS and have it service two SSL certificates based on host name? I know that with the basic IIS configuration that this is not possible, but I was thinking that with some sort of combination of external load balancing and/or SSL acceleration servers/services that we could have these servers process the SSL request and leave IIS clean to have one single application. I am not familiar at all with these technologies, hence the reason I am asking if it is theoretically possible. If not, does anyone else know how to achieve this?

    Read the article

< Previous Page | 520 521 522 523 524 525 526 527 528 529 530 531  | Next Page >