Search Results

Search found 23131 results on 926 pages for 'ms query'.

Page 525/926 | < Previous Page | 521 522 523 524 525 526 527 528 529 530 531 532  | Next Page >

• Windows 2008 Unknown Disks

  - by Ailbe

  I have a BL460c G7 blade server with OS Windows 2008 R2 SP1. This is a brand new C7000 enclosure, with FlexFabric interconnects. I got my FC switches setup and zoned properly to our Clariion CX4, and can see all the hosts that are assigned FCoE HBAs on both paths in both Navisphere and in HP Virtual Connect Manager. So I went ahead and created a storage group for a test server, assigned the appropriate host, assigned the LUN to the server. So far so good, log onto server and I can see 4 unknown disks.... No problem, I install MS MPIO, no luck, can't initialize the disks, and the multiple disks don't go away. Still no problem, I install PowerPath version 5.5 reboot. Now I see 3 disks. One is initialized and ready to go, but I still have 2 disks that I can't initialize, can't offline, can't delete. If I right click in storage manager and go to properties I can see that the MS MPIO tab, but I can't make a path active. I want to get rid of these phantom disks, but so far nothing is working and google searches are showing up some odd results, so obviously I'm not framing my question right. I thought I'd ask here real quick. Does anyone know a quick way to get rid of these unknown disks. Another question, do I need the MPIO feature installed if I have PowerPath installed? This is my first time installing Windows 2008 R2 in this fashion and I'm not sure if that feature is needed or not right now. So some more information to add to this. It seems I'm dealing with more of a Windows issue than anything else. I removed the LUN from the server, uninstalled PowerPath completely, removed the MPIO feature from the server, and rebooted twice. Now I am back to the original 4 Unknown Disks (plus the local Disk 0 containing the OS partition of course, which is working fine) I went to diskpart, I could see all 4 Unknown disks, I selected each disk, ran clean (just in case i'd somehow brought them online previously as GPT and didn't realize it) After a few minutes I was no longer able to see the disks when I ran list disk. However, the disks are still in Disk Management. When I try and offline the disks from Disk Management I get an error: Virtual Disk Manager - The system cannot find the file specified. Accompanied by an error in System Event Logs: Log Name: System Source: Virtual Disk Service Date: 6/25/2012 4:02:01 PM Event ID: 1 Task Category: None Level: Error Keywords: Classic User: N/A Computer: hostname.local Description: Unexpected failure. Error code: 2@02000018 Event Xml: 1 2 0 0x80000000000000 4239 System hostname.local 2@02000018 I feel sure there is a place I can go in the Registry to get rid of these, I just can't recall where and I am loathe to experiement. So to recap, there are currently no LUNS attached at all, I still have the phantom disks, and I'm getting The system cannot find the file specified from Virtual Disk Manager when I try to take them offline. Thanks!

  Read the article

• Lock down Wiki access to password only but remain open to a subnet via .htaccess

  - by Treffynnon

  Basically we have a Wiki that has some sensitive information stored in it - not the best I know but my predecessor set it up. I want to be able to request password access from any one who is not on the local network subnet. Those on the local subnet should be able to proceed without entering a password. The following .htaccess does not seem to work any more as it is letting non-local access without requiring the password: AuthName "Our Wiki" AuthType Basic AuthUserFile /path/to/passwd/file AuthGroupFile /dev/null Require valid-user Allow from 192.168 Satisfy Any order deny,allow And I cannot work out why. The WikkaWiki it is supposed to be protecting was recently upgraded, which clobbered the .htaccess file so I restored the above from memory/googling. Maybe I am missing an important directive? The full .htaccess is as follows: AuthName "Our Wiki" AuthType Basic AuthUserFile /path/to/passwd/file AuthGroupFile /dev/null Require valid-user Allow from 192.168 Satisfy Any SetEnvIfNoCase Referer ".*($LIST_OF_ADULT_WORDS).*" BadReferrer order deny,allow deny from env=BadReferrer <IfModule mod_rewrite.c> # turn on rewrite engine RewriteEngine on RewriteBase / # if request is a directory, make sure it ends with a slash RewriteCond %{REQUEST_FILENAME} -d RewriteRule ^(.*/[^/]+)$ $1/ # if not rewritten before, AND requested file is wikka.php # turn request into a query for a default (unspecified) page RewriteCond %{QUERY_STRING} !wakka= RewriteCond %{REQUEST_FILENAME} wikka.php RewriteRule ^(.*)$ wikka.php?wakka= [QSA,L] # if not rewritten before, AND requested file is a page name # turn request into a query for that page name for wikka.php RewriteCond %{QUERY_STRING} !wakka= RewriteRule ^(.*)$ wikka.php?wakka=$1 [QSA,L] </IfModule>

  Read the article

• Logging hurts MySQL performance - but, why?

  - by jimbo

  I'm quite surprised that I can't see an answer to this anywhere on the site already, nor in the MySQL documentation (section 5.2 seems to have logging otherwise well covered!) If I enable binlogs, I see a small performance hit (subjectively), which is to be expected with a little extra IO -- but when I enable a general query log, I see an enormous performance hit (double the time to run queries, or worse), way in excess of what I see with binlogs. Of course I'm now logging every SELECT as well as every UPDATE/INSERT, but, other daemons record their every request (Apache, Exim) without grinding to a halt. Am I just seeing the effects of being close to a performance "tipping point" when it comes to IO, or is there something fundamentally difficult about logging queries that causes this to happen? I'd love to be able to log all queries to make development easier, but I can't justify the kind of hardware it feels like we'd need to get performance back up with general query logging on. I do, of course, log slow queries, and there's negligible improvement in general usage if I disable this. (All of this is on Ubuntu 10.04 LTS, MySQLd 5.1.49, but research suggests this is a fairly universal issue)

  Read the article

• Locating memory leak in Apache httpd process, PHP/Doctrine-based application

  - by Sam

  I have a PHP application using these components: Apache 2.2.3-31 on Centos 5.4 PHP 5.2.10 Xdebug 2.0.5 with Remote Debugging enabled APC 3.0.19 Doctrine ORM for PHP 1.2.1 using Query Caching and Results Caching via APC MySQL 5.0.77 using Query Caching I've noticed that when I start up Apache, I eventually end up 10 child processes. As time goes on, each process will grow in memory until each one approaches 10% of available memory, which begins to slow the server to a crawl since together they grow to take up 100% of memory. Here is a snapshot of my top output: PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1471 apache 16 0 626m 201m 18m S 0.0 10.2 1:11.02 httpd 1470 apache 16 0 622m 198m 18m S 0.0 10.1 1:14.49 httpd 1469 apache 16 0 619m 197m 18m S 0.0 10.0 1:11.98 httpd 1462 apache 18 0 622m 197m 18m S 0.0 10.0 1:11.27 httpd 1460 apache 15 0 622m 195m 18m S 0.0 10.0 1:12.73 httpd 1459 apache 16 0 618m 191m 18m S 0.0 9.7 1:13.00 httpd 1461 apache 18 0 616m 190m 18m S 0.0 9.7 1:14.09 httpd 1468 apache 18 0 613m 190m 18m S 0.0 9.7 1:12.67 httpd 7919 apache 18 0 116m 75m 15m S 0.0 3.8 0:19.86 httpd 9486 apache 16 0 97.7m 56m 14m S 0.0 2.9 0:13.51 httpd I have no long-running scripts (they all terminate eventually, the longest being maybe 2 minutes long), and I am working under the assumption that once each script terminates, the memory it uses gets deallocated. (Maybe someone can correct me on that). My hunch is that it could be APC, since it stores data between requests, but at the same time, it seems weird that it would store data inside the httpd process. How can I track down which part of my app is causing the memory leak? What tools can I use to see how the memory usage is growing inside the httpd process and what is contributing to it?

  Read the article

• Securing smtp with login

  - by Paul Peelen

  I have a ispconfig server, and it seems that someone is using it to send spam. I got about 130 "Mail Delivery System" email about declined send email. This spammer uses my email address as sent from adress, so I get all these email adresses to my mail. I am using Postfix and Courier. I installed my server according to this guide: http://www.howtoforge.com/perfect-server-debian-lenny-ispconfig3-p3 I did this a few months ago. My question: Can I secure my server to require login to be able to send email, and if so... how? Thanks! EDIT Some data from mail.log, these kind of error show up constantly: Jun 15 17:58:16 bolt postfix/qmgr[10712]: CC7DA1242AE: from=<paul@*****.se>, size=3782, nrcpt=1 (queue active) Jun 15 17:58:16 bolt postfix/smtp[11337]: CC7DA1242AE: to=<[email protected]>, relay=none, delay=4641, delays=4640/0.01/0.32/0, dsn=4.4.3, status=deferred (Host or domain name not found. Name service error for name=cmlisboa.pt type=MX: Host not found, try again) Jun 15 17:58:19 bolt postfix/smtpd[10836]: connect from static-200-105-220-154.acelerate.net[200.105.220.154] Jun 15 17:58:20 bolt postfix/smtpd[10836]: NOQUEUE: reject: RCPT from static-200-105-220-154.acelerate.net[200.105.220.154]: 550 5.1.1 <advertising@*****.com>: Recipient address rejected: User unknown in virtual mailbox table; from=<[email protected]> to=<advertising@*****.com> proto=ESMTP helo=<static-200-105-220-154.acelerate.net> Jun 15 17:58:20 bolt postfix/smtpd[10836]: lost connection after DATA (0 bytes) from static-200-105-220-154.acelerate.net[200.105.220.154] Jun 15 17:58:20 bolt postfix/smtpd[10836]: disconnect from static-200-105-220-154.acelerate.net[200.105.220.154] Jun 15 17:58:29 bolt postfix/smtpd[10834]: connect from unknown[62.176.172.226] Jun 15 17:58:32 bolt postfix/smtpd[10834]: 386791241F9: client=unknown[62.176.172.226] Jun 15 17:58:34 bolt postfix/cleanup[10975]: 386791241F9: message-id=<[email protected]> Jun 15 17:58:34 bolt postfix/qmgr[10712]: 386791241F9: from=<[email protected]>, size=867, nrcpt=1 (queue active) Jun 15 17:58:35 bolt postfix/smtpd[10834]: disconnect from unknown[62.176.172.226] Jun 15 17:58:35 bolt amavis[11084]: (11084-17) Blocked SPAM, [62.176.172.226] [62.176.172.226] <[email protected]> -> <*****@*****>, Message-ID: <[email protected]>, mail_id: XczovKoMBYNr, Hits: 18.471, size: 867, 833 ms Jun 15 17:58:35 bolt postfix/smtp[10732]: 386791241F9: to=<*****@*****>, relay=127.0.0.1[127.0.0.1]:10024, delay=3.5, delays=2.7/0/0/0.83, dsn=2.7.0, status=sent (250 2.7.0 Ok, discarded, id=11084-17 - SPAM) Jun 15 17:58:35 bolt postfix/qmgr[10712]: 386791241F9: removed Jun 15 17:58:43 bolt postfix/smtpd[10836]: warning: 178.121.154.194: address not listed for hostname mm-194-154-121-178.dynamic.pppoe.mgts.by Jun 15 17:58:43 bolt postfix/smtpd[10836]: connect from unknown[178.121.154.194] Jun 15 17:58:45 bolt postfix/smtpd[10727]: connect from unknown[180.134.223.86] EDIT #2 Got some more info from the logs, this is a send request: mail.info.1:Jun 15 16:41:57 bolt amavis[5399]: (05399-06) Passed CLEAN, [110.139.48.64] [110.139.48.64] <paul@*****.se> -> <[email protected]>, Message-ID: <CHILKAT-MID-7c54ebcf-5501-de9b-f0b1-4f0234290d8d@HP-IRISH>, mail_id: 35l56Ramx6Nc, Hits: -2.941, size: 3329, queued_as: 2485770086, 136 ms mail.info.1:Jun 15 16:41:57 bolt postfix/smtp[4743]: 375C570082: to=<[email protected]>, relay=127.0.0.1[127.0.0.1]:10024, delay=4.8, delays=4.7/0/0/0.14, dsn=2.0.0, status=sent (250 2.0.0 Ok, id=05399-06, from MTA([127.0.0.1]:10025): 250 2.0.0 Ok: queued as 2485770086) Which apparently got thrue. Any ideas how to restrict this?

  Read the article

• Intermittent 404 on select assets, LAMP stack

  - by Tom Lagier

  We have a LAMP stack WordPress server that is serving most assets correctly. However, one plugin's CSS file and several images are returning soft 404s roughly 20% of the time. I can't find any reference to the 404 in the access logs, but the browser is definitely receiving a 404 response from somewhere (WordPress, I would assume). When I use an alias URL that does not match the site URL but does resolve to the asset path, the resource loads correctly 100% of the time. However, using the site url only resolves for the select, problematic assets 20% of the time. You can test one of the problematic assets here: http://www.mreco.org/wp-content/uploads/2014/05/zero-cost.jpg However the alias link always resolves correctly: http://mr-eco.wordpress.promocampaigns.com/wp-content/uploads/2014/05/zero-cost.jpg Stranger, if I attempt to access outdated content that definitely does not exist on the server, at the live URL it returns the content roughly 50% of the time. Using the alias link, it 404s 100% of the time - the correct behavior. Error log and PHP error log are clean. A sample access log (pulled from grep 'zero-cost.jpg' /var/log/httpd/mr-eco-access_log) from several refreshes of the live direct link (where I am not seeing any 404's): 10.166.202.202 - - [28/May/2014:20:27:41 +0000] "GET /wp-content/uploads/2014/05/zero-cost.jpg HTTP/1.1" 304 - 10.166.202.202 - - [28/May/2014:20:27:42 +0000] "GET /wp-content/uploads/2014/05/zero-cost.jpg HTTP/1.1" 304 - 10.166.202.202 - - [28/May/2014:20:27:43 +0000] "GET /wp-content/uploads/2014/05/zero-cost.jpg HTTP/1.1" 304 - 10.166.202.202 - - [28/May/2014:20:27:43 +0000] "GET /wp-content/uploads/2014/05/zero-cost.jpg HTTP/1.1" 304 - 10.176.201.37 - - [28/May/2014:20:27:56 +0000] "GET /wp-content/uploads/2014/05/zero-cost.jpg HTTP/1.1" 200 57027 Chrome's dev tools list the following network activity before displaying 404 page content: zero-cost.jpg /wp-content/uploads/2014/05 GET 404 Not Found text/html Other 15.9?KB 73.2?KB 953?ms 947?ms My Apache configuration is standard, I've listed the virtual host entry and .htaccess file below. I can provide other parts of Apache config if necessary. Virtual host: <VirtualHost *:80> DocumentRoot /var/www/public_html/mr-eco.wordpress.promocampaigns.com ServerName www.mreco.org ServerAlias mreco.org mr-eco.wordpress.promocampaigns.com ErrorLog logs/mr-eco-error_log CustomLog logs/mr-eco-access_log common <Directory /var/www/public_html/mr-eco.wordpress.promocampaigns.com> AllowOverride All SetOutputFilter DEFLATE </Directory> </VirtualHost> .htaccess: # BEGIN WordPress <IfModule mod_rewrite.c> RewriteEngine On RewriteBase / RewriteRule ^index\.php$ - [L] RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule . /index.php [L] </IfModule> # END WordPress I have checked for multiple A records and can confirm that there is a single A record pointing at the domain: ;; ANSWER SECTION: mreco.org. 60 IN A 50.18.58.174 I'm fairly new to systems administration, and at a complete loss as to what could cause this. In the past, inconsistently 404ing assets have been because of out-of-sync instances behind a load balancer. In this case, it is a single instance behind the load balancer. Because of the inconsistency, it feels like a caching issue. We don't make use of Apache caching, and as far as I know WordPress should not be caching either. What I've done so far: Reset WordPress permalinks Disabled WordPress plugins Re-generated WordPress .htaccess file Swapped ServerName and ServerAlias directives Cleared browser cache Confirmed disk location of resources Checked PHP, access, and error logs Confirmed correct DNS setup (can post if necessary) I'm at a total loss. Thanks for helping me out!

  Read the article

• Mac compatible Web-Development Tools

  - by Derek Adair

  Hi, I'm looking for any Mac compatibile development tools that are tried and tested. I'm quite sick of my MySQL query browser crashing... And i'm sure there is probably better software out there anyways... At the moment my focus is dedicated to application development using PHP/MySQL/Ajax. (although, I will be learning ActionScript/Flex shortly). Here are the apps I regularly use and a general idea of the environment I work in: Hosting - localhost: Mamp Production: Amazon EC2 IDE - Coda: PHP/Mysql/Javascript Mysql - PHPMyAdmin MySQL query browser FTP - Coda FileZilla X11 is used for connecting to my production environment I am mainly looking for... -tools that will help me better manage (create, edit... whatever) databases. -Version control. This is huge as I'm working with a team of three other developers (we reeeeeeaaally need to standardize our environments..) Although any cool little tools to make my job easier are always a plus! I am unable to insert more than one link as I'm not rated on this forum.

  Read the article

• MySQL /G output

  - by conandor

  I ran mysql query as below on a non-partition table mysql> use test31 Reading table information for completion of table and column names You can turn off this feature to get a quicker startup with -A Database changed mysql> explain partitions SELECT * FROM my_friends WHERE (requestor = '1234567890' OR contact = '1234567890') AND status = 1 ORDER BY request_id DESC LIMIT 0,100\G *************************** 1. row *************************** id: 1 select_type: SIMPLE table: my_friends partitions: NULL type: index_merge possible_keys: friend_index,requestor,contact key: friend_index,contact key_len: 17,17 ref: NULL rows: 2 Extra: Using sort_union(friend_index,contact); Using where; Using filesort 1 row in set (0.00 sec) on a partition table mysql> explain partitions SELECT * FROM my_friends WHERE (requestor = '1234567890' OR contact = '1234567890') AND status = 1 ORDER BY request_id DESC LIMIT 0,100\G *************************** 1. row *************************** id: 1 select_type: SIMPLE table: my_friends partitions: p1_p1sp0,p1_p1sp1,p1_p1sp2,p1_p1sp3,p1_p1sp4,p1_p1sp5,p1_p1sp6,p1_p1sp7,p1_p1sp8,p1_p1sp9,p1_p1sp10,p1_p1sp11,p1_p1sp12,p1_p1sp13,p1_p1sp14,p1_p1sp15,p1_p1sp16,p1_p1sp17,p1_p1sp18,p1_p1sp19,p1_p1sp20,p1_p1sp21,p1_p1sp22,p1_p1sp23,p1_p1sp24,p1_p1sp25,p1_p1sp26,p1_p1sp27,p1_p1sp28,p1_p1sp29 type: index_merge possible_keys: friend_index,requestor,contact key: friend_index,contact key_len: 17,17 ref: NULL rows: 60 Extra: Using sort_union(friend_index,contact); Using where; Using filesort 1 row in set (0.01 sec) What does the "rows" mean? less rows is more faster query?

  Read the article

• Coldfusion 9 losing connection to MySQL 5 database server a couple of weeks after the server is started

  - by user1503757

  We get the following Coldfusion error message after our server have been running for a couple of weeks: Error Executing Database Query.Could not create connection to database server. Attempted reconnect 3 times We run Coldfusion Enterprise 9 on a one year old XServer with Snow Leopard and MySQL 5 The server has about ten DSN set up in the Coldfusion Administrator All local, with default advanced settings, and host set to "localhost" The server is not under heavy load. The strange thing is that after a restart of the server, everything works fine. Then after a week or so, some databases will stop working, in the sense that Coldfusion cannot create a connection to them. If I then go to the Coldfusion Administrator and click "Verify all datasources", I will get that only 2 or 3 got verified, the other ones failed, and it is always the same datasources that can't be verified when the server starts to behave like this if I try to verify again, BUT NOT neccessary the same datasources that couldn't be verified the last time the server behaved like this. I know about the setting "max_connections" and we have included a line for that setting in the MySQL config file and set it to 2000, and when we read it by a query it says "2000", so that can't be the problem. Anyone?

  Read the article

• --log-slave-updates is OFF but updates received from master are still logged to slave binary log?

  - by quanta

  MySQL version 5.5.14 According to the document, by the default, slave does not log to its binary log any updates that are received from a master server. Here are my config. on the slave: # egrep 'bin|slave' /etc/my.cnf relay-log=mysqld-relay-bin log-bin = /var/log/mysql/mysql-bin binlog-format=MIXED sync_binlog = 1 log-bin-trust-function-creators = 1 mysql> show global variables like 'log_slave%'; +-------------------+-------+ | Variable_name | Value | +-------------------+-------+ | log_slave_updates | OFF | +-------------------+-------+ 1 row in set (0.01 sec) mysql> select @@log_slave_updates; +---------------------+ | @@log_slave_updates | +---------------------+ | 0 | +---------------------+ 1 row in set (0.00 sec) but slave still logs the updates that are received from a master to its binary logs, let's see the file size: -rw-rw---- 1 mysql mysql 37M Apr 1 01:00 /var/log/mysql/mysql-bin.001256 -rw-rw---- 1 mysql mysql 25M Apr 2 01:00 /var/log/mysql/mysql-bin.001257 -rw-rw---- 1 mysql mysql 46M Apr 3 01:00 /var/log/mysql/mysql-bin.001258 -rw-rw---- 1 mysql mysql 115M Apr 4 01:00 /var/log/mysql/mysql-bin.001259 -rw-rw---- 1 mysql mysql 105M Apr 4 18:54 /var/log/mysql/mysql-bin.001260 and the sample query when reading these binary files with mysqlbinlog utility: #120404 19:08:57 server id 3 end_log_pos 110324763 Query thread_id=382435 exec_time=0 error_code=0 SET TIMESTAMP=1333541337/*!*/; INSERT INTO norep_SplitValues VALUES ( NAME_CONST('cur_string',_utf8'118212' COLLATE 'utf8_general_ci')) /*!*/; # at 110324763 Did I miss something?

  Read the article

• Apache2 - rewrite a bunch of specified pathname URLs to one URL

  - by James Nine

  I need to rewrite a bunch of urls (about 100 or so) for SEO purposes, and there may be more being added in the future (probably another 50-100 later on). I need a flexible way of doing this and so far, the only way I can think of is to edit the .htaccess file using the rewrite engine. For example, I have a bunch of urls like this (please note that the query string is irrelevant, and dynamic; it could be anything. I was only using them purely as an example. I am only focusing on the pathname--the part between the hostname and query string, as marked in bold below): http://example.com/seo_term1?utm_source=google&utm_medium=cpc&utm_campaign=seo_term http://example.com/another_seo_term2?utm_source=facebook&utm_medium=cpc&utm_campaign=seo_term http://example.com/yet_another_seo_term3?utm_source=example_ad_network&utm_medium=cpc&utm_campaign=seo_term http://example.com/foobar_seo_term4 http://example.com/blah_seo_term5?test=1 etc... And they are all being rewritten to (for now): http://example.com/ What's the most efficient/effective way of doing this so that I may be able to add more terms in the future? One solution I came across is to do this (in the .htaccess file): RewriteEngine on RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule ^(.*)$ / [NC,QSA] However, the problem with this solution is that even invalid urls (such as http://example.com/blah) will be rewritten to http://example.com instead of giving a 404 code (which is what it is supposed to do anyway). I'm still trying to figure out how all this works, and the only way I can think of is to write 100 more RewriteCond statements (such as: RewriteCond %{REQUEST_URI} =/seo_term1 [NC,OR]) before the RewriteRule directive. For example: RewriteEngine on RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteCond %{REQUEST_URI} =/seo_term1 [NC,OR] RewriteCond %{REQUEST_URI} =/another_seo_term2 [NC,OR] RewriteCond %{REQUEST_URI} =/yet_another_seo_term3 [NC,OR] RewriteCond %{REQUEST_URI} =/foobar_seo_term4 [NC,OR] RewriteCond %{REQUEST_URI} =/blah_seo_term5 [NC] RewriteRule ^(.*)$ / [NC,QSA] But that doesn't sound very efficient to me. Is there a better way?

  Read the article

• Google Chrome doesn't delete my browsing history correctly

  - by Derfder

  I have deleted everything that I could from my browser history: chrome://settings/clearBrowserData I checked everything and select the begining of time Then when I access browsing history: chrome://history/ There is nothing (as I expected), or to be precise No history entries found. The problem is that I still see my specific search url with very specific query I have made a month ago, when I start typing the url of the website into chrome address bar. How is that possible? Where is Google stroing these data. How to get rid off them completely? I want to mention that my autosuggestion options look like this: So, what else should I delete to remove everything from autosuggestions? Right now it has some specific URLs (subpages, pages with very specific search query I have made in a month or so). I have tried restarting Chrome and restarting my computer, but the urls are still in the autosuggestion. Also I am unable to turn off the autosuggestion, even I have unchecked that option in settings. My Google Chrome version is: Version 27.0.1453.116 m (probably the latest) Btw. in Firefox deleting the history works as expected. So, I guess that this has nothing to do with the operating system I am using (Windows 7), but only it's an issue with Chrome itself.

  Read the article

• Mac OS X - configuring ntpd server with on LAN with D-Link DIR-655

  - by Mark C

  Hey all, This question is pretty specific, but I hope someone will have seen this error elsewhere. I a configuring a machine running OS X 10.5.8 to be an NTP server for machines connected to a LAN that is not connected to the Internet. I am not too worried about knowing the "right" time on all the machines, but rather worried about making sure everyone has the same notion of time. I configured the NTP daemon on Mac by turning on the Set date and time automatically in System Preferences, using the server's clock, 127.127.1.0 as the reference clock. I figured I should see if the server can NTP query itself before proceeding to the clients. The weird part is when I run the ntpq -p command in a command-prompt when connected to my D-Link DIR-655 (firmware: 1.33), it hangs for about a minute or so each time before finally giving me some output. I thought the problem might have to do with Port Forwarding, so I configured the router to forward port 123 for the IP of the server, but that did not improve the situation. When I run the ntpq -p command on my school's network, on a Linksys WRT54G router, or with the wireless Airport card turned off - I have absolutely no problems - the command returns a response instantly. Is this normal? I can see why a query might take a minute or so, but I don't understand why one router does it faster than the other. I tried messing around with the ntp.conf file adding the burst, minpoll, and maxpoll options: server 127.127.1.0 burst minpoll 4 maxpoll 5 Figuring that perhaps I am polling too often and the configuration file is slowing me down, but even with this, the ntpq still hangs on the D-Link DIR-655, but does just fine on the other routers. Any thoughts on where the lag is coming from or if the lag is even a problem?

  Read the article

• nginx + php-fpm cycle redirection error on linode new vps

  - by chifliiiii

  I'm new to nginx, and I'm trying to make my first server run. I followed this guide as I'm trying to use it for a multisite wordpress site. After installing everything, I get a 500 Internal server error. If I check logs, I see this: 012/09/27 08:55:54 [error] 11565#0: *8 rewrite or internal redirection cycle while internally redirecting to "/index.html", client: xxx.xxx.xxx.xxx, server: localhost, request: "GET /favicon.ico HTTP/1.1", host: "www.mydomain.com" 2012/09/27 08:59:32 [error] 11618#0: *1 rewrite or internal redirection cycle while internally redirecting to "/index.html", client: xxx.xxx.xxx.xxx, server: localhost, request: "GET /phpmyadmin HTTP/1.1", host: "www.mydomain.com" My conf files are the following: nano /etc/nginx/sites-available/mydomain.com server { listen 80 default_server; server_name mydomain.com *.mydomain.com; root /srv/www/aciup.com/public; access_log /srv/www/mydomain.com/log/access.log; error_log /srv/www/mydomain.com/log/error.log; location / { index index.php; try_files $uri $uri/ /index.php?$args; } # Add trailing slash to */wp-admin requests. rewrite /wp-admin$ $scheme://$host$uri/ permanent; # Directives to send expires headers and turn off 404 error logging. location ~* \.(js|css|png|jpg|jpeg|gif|ico)$ { expires 24h; log_not_found off; } # this prevents hidden files (beginning with a period) from being served location ~ /\. { access_log off; log_not_found off; deny all; } # Pass uploaded files to wp-includes/ms-files.php. rewrite /files/$ /index.php last; if ($uri !~ wp-content/plugins) { rewrite /files/(.+)$ /wp-includes/ms-files.php?file=$1 last; } # Rewrite multisite '.../wp-.*' and '.../*.php'. if (!-e $request_filename) { rewrite ^/[_0-9a-zA-Z-]+(/wp-.*) $1 last; rewrite ^/[_0-9a-zA-Z-]+.*(/wp-admin/.*\.php)$ $1 last; rewrite ^/[_0-9a-zA-Z-]+(/.*\.php)$ $1 last; } location ~ \.php$ { client_max_body_size 25M; fastcgi_pass unix:/var/run/php5-fpm.sock; fastcgi_index index.php; include /etc/nginx/fastcgi_params; } } nano /etc/nginx/nginx.conf user www-data; worker_processes 4; worker_cpu_affinity 0001 0010 0100 1000; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 2048; } http { include /etc/nginx/mime.types; access_log /var/log/nginx/access.log; sendfile on; tcp_nopush on; keepalive_timeout 5; tcp_nodelay on; server_tokens off; gzip on; gzip_types text/plain text/css application/x-javascript text/xml application/xml application/xml+rss text/javascript; gzip_disable "MSIE [1-6]\.(?!.*SV1)"; include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; } Any help will be appreciated.

  Read the article

• How to recover the plesk database?

  - by Kau-Boy

  When I try to launch the Plesk administration page of you server I get the following error: ERROR: PleskMainDBException MySQL query failed: MySQL server has gone away The MySQL Server is working well. Although it seems that the plesk database is somehow corrupt and any action on this database results in a restart of the mysql process, so even queries to other databases on the same MySQL server will be lost. If I try to connect to the plesk database using phpMyAdmin, I can only see the number of tables, the database had originally. But I am not able to open the tables listing. As soon as I try it, the mysql process crashes again. Trying to connect to the database using ssh works. I can even run a SELECT statement against any table an get a result. I don't know if it is an plesk error or an error of the psa database or even the MySQL server. Can you give me any tips on how to recover the plesk system. Should I try to repair the Plesk installation before. And if so, how can I do it and will all my settings get lost doing it? EDIT: Trying to dump the database, I get the following error: mysqldump: Got error: 2013: Lost connection to MySQL server during query when using LOCK TABLES

  Read the article

• Replicated MongoDB server slower than simple shards

  - by displayName

  I tried to compare the performance of a sharded configuration against a sharded and replicated configuration. The sharded configuration consists of 8 shards each running on three different machines thereby constituting a total of 24 shards. All 8 of these shards run in the same partition on each machine. The sharded and replicated version is 8 shards again just like plain sharding, and all 8 mongods run on the same partition in each machine. But apart from this, each of these three machine now run additional 16 threads on another partition which serve as the secondary for the 8 mongods running on other machines. This is the way I prepared a sharded and replicated configuration with data chunks having replication factor of 3. Important point to note is that once the data has been loaded, it is not modified. So after primary and secondaries have synchronized then it doesn't matter which one i read from. To run the queries, I use an entirely different machine (let's call it config) which runs mongos and this machine's only purpose is to receive queries and run them on the cluster. Contrary to my expectations, plain sharding of 8 threads on each machine (total = 3 * 8 = 24) is performing better for queries than the sharded + replicated configuration. I have a script written to perform the query. So in order to time the scripts, I use time ./testScript and see the result. I tried changing the reading preference for replicated cluster by logging to mongo of config and run db.getMongo().setReadPref('secondary') and then exit the shell and run the queries like time ./testScript. The questions are: Where am i going wrong in the replication? Why is it slower than its plain sharding version? Does the db.getMongo().ReadPref('secondary') persist when i leave the shell and try to perform the query? All the four machines are running Linux and i have already increased the ulimit -n to 2048 from initial value of 1024 to allow more connections. The collections are properly distributed and all the mongods have equal number of chunks. Goes without saying that indices in both configurations are the same.

  Read the article

• IMAPSync Migration to Exchange 2010 SP1: Exchange drops connections while checking for existence of folders

  - by Benjamin Priestman

  I'm migrating from ZImbra Collaboration Suite to Exchange 2010 SP1. I'm testing IMAPSync as a possible migration tool and have hit a problem with the IMAP server in Exchange 2010. For each account it migrates, IMAPSync loops through the list of folders in the source mailbox and tests for the existence of each one in the destination mailbox. It then goes on to create those folders that do not exist and copy over the messages. It's the intial testing for the existence of the folders that is giving me a problem. The response given by the Exchange server when the folder does not yet exist is given as an error: "R=""16 NO IMAPSyncTest/8 doesn't exist."" After ten of these errors have been issued in succession, the Exchange server appears to stop responding to the IMAP session. Enabling protocol logging for IMAP confirms that the 10th request for a non-existant folder is the last request to be logged on the server. IMAPSync carries on merrily without seeming to realise its connection has gone and thus fails to create any folders. I've logged this with the tool's creator. Does anyone have any idea why Exchange is stopping responding to the connections though? The behaviour looks rather like throttling, although the 'ten strikes and you're out' trigger does not seem to correspond to any of the triggers on the ThrottlingPolicies. Just to check, I've tried creating a new ThrottlingPolicy, turned everything that I think might be relevant up to 11 and applied it to the my test mailbox. Policy settings are listed below, along with IMAP settings. Everything else should be pretty much as default. Throttling Policy RunspaceId : afa3159c-32a6-4906-986f-8adfbe50868b IsDefault : False AnonymousMaxConcurrency : 1 AnonymousPercentTimeInAD : AnonymousPercentTimeInCAS : AnonymousPercentTimeInMailboxRPC : EASMaxConcurrency : 10 EASPercentTimeInAD : EASPercentTimeInCAS : EASPercentTimeInMailboxRPC : EASMaxDevices : 10 EASMaxDeviceDeletesPerMonth : EWSMaxConcurrency : 10 EWSPercentTimeInAD : 50 EWSPercentTimeInCAS : 90 EWSPercentTimeInMailboxRPC : 60 EWSMaxSubscriptions : 5000 EWSFastSearchTimeoutInSeconds : 60 EWSFindCountLimit : 1000 IMAPMaxConcurrency : 1000 IMAPPercentTimeInAD : 400 IMAPPercentTimeInCAS : 400 IMAPPercentTimeInMailboxRPC : 400 OWAMaxConcurrency : 5 OWAPercentTimeInAD : 30 OWAPercentTimeInCAS : 150 OWAPercentTimeInMailboxRPC : 150 POPMaxConcurrency : 20 POPPercentTimeInAD : POPPercentTimeInCAS : POPPercentTimeInMailboxRPC : PowerShellMaxConcurrency : 18 PowerShellMaxTenantConcurrency : PowerShellMaxCmdlets : PowerShellMaxCmdletsTimePeriod : ExchangeMaxCmdlets : PowerShellMaxCmdletQueueDepth : PowerShellMaxDestructiveCmdlets : PowerShellMaxDestructiveCmdletsTimePeriod : RCAMaxConcurrency : 1000 RCAPercentTimeInAD : 400 RCAPercentTimeInCAS : 400 RCAPercentTimeInMailboxRPC : 400 CPAMaxConcurrency : 20 CPAPercentTimeInCAS : 205 CPAPercentTimeInMailboxRPC : 200 MessageRateLimit : RecipientRateLimit : ForwardeeLimit : CPUStartPercent : 75 AdminDisplayName : ExchangeVersion : 0.10 (14.0.100.0) Name : TestMigrationThrottling DistinguishedName : CN=TestMigrationThrottling,CN=Global Settings,CN=Our Company,CN=Microsoft Exchange,CN=Services,CN=Configuration,DC=cimex,DC=com Identity : TestMigrationThrottling Guid : 240049b3-2023-4df1-8edc-fbfc1fc80b87 ObjectCategory : domain.com/Configuration/Schema/ms-Exch-Throttling-Policy ObjectClass : {top, msExchGenericPolicy, msExchThrottlingPolicy} WhenChanged : 21/04/2011 18:48:19 WhenCreated : 21/04/2011 18:07:20 WhenChangedUTC : 21/04/2011 17:48:19 WhenCreatedUTC : 21/04/2011 17:07:20 OrganizationId : OriginatingServer : a-domain-controller IsValid : True IMAPSettings RunspaceId : afa3159c-32a6-4906-986f-8adfbe50868b ProtocolName : IMAP4 Name : 1 MaxCommandSize : 10240 ShowHiddenFoldersEnabled : False UnencryptedOrTLSBindings : {192.168.x.x:143} SSLBindings : {192.168.x.x:993} InternalConnectionSettings : {mail.office.domain.com:143:TLS, mail.office.domain.com:993:SSL} ExternalConnectionSettings : {mail.office.domain.com:143:TLS, mail.office.domain.com:993:SSL} X509CertificateName : mail.domain.com Banner : The Microsoft Exchange IMAP4 service is ready. LoginType : SecureLogin AuthenticatedConnectionTimeout : 00:30:00 PreAuthenticatedConnectionTimeout : 00:01:00 MaxConnections : 2147483647 MaxConnectionFromSingleIP : 2147483647 MaxConnectionsPerUser : 16 MessageRetrievalMimeFormat : BestBodyFormat ProxyTargetPort : 143 CalendarItemRetrievalOption : iCalendar OwaServerUrl : EnableExactRFC822Size : False LiveIdBasicAuthReplacement : False SuppressReadReceipt : False ProtocolLogEnabled : True EnforceCertificateErrors : False LogFileLocation : C:\Program Files\Microsoft\Exchange Server\V14\Logging\Imap4 LogFileRollOverSettings : Daily LogPerFileSizeQuota : 0 B (0 bytes) ExtendedProtectionPolicy : None EnableGSSAPIAndNTLMAuth : True Server : CMX-OFFICE-EX01 AdminDisplayName : ExchangeVersion : 0.10 (14.0.100.0) DistinguishedName : CN=1,CN=IMAP4,CN=Protocols,CN=EXCHANGE01,CN=Servers,CN=Exchange Administrative Group (FYDIBOHF23SPDLT),CN=Administrative Groups,CN=Our COmpany,CN=Microsoft Exchange,CN=Services,CN=Configuration,DC=domain,DC=com Identity : EXCHANGE01\1 Guid : 48f9dc37-74c2-4fb0-a042-641f863f45f2 ObjectCategory : domain.com/Configuration/Schema/ms-Exch-Protocol-Cfg-IMAP-Server ObjectClass : {top, protocolCfg, protocolCfgIMAP, protocolCfgIMAPServer} WhenChanged : 21/04/2011 17:03:39 WhenCreated : 15/04/2011 13:51:58 WhenChangedUTC : 21/04/2011 16:03:39 WhenCreatedUTC : 15/04/2011 12:51:58 OrganizationId : OriginatingServer : a-domain-server IsValid : True

  Read the article

• Is it possible to configure simultaneous authentication against 2 different AD domains by IIS 7?

  - by just3ws

  Basically, I need to be able to attempt to authenticate against two different AD domains from IIS. I'd like to be able to automatically query both AD's and whichever comes back with an authentication wins. The users are completely separate and will only exist in their respective domain.         IIS           |           |   /-------------\   |                 |  ------        ------  AD1         AD2  JoeU        AmyU  JillU         JohnU So, if IIS requests to authenticate JoeU it will query both domains. JoeU will be found in AD1 so we can ignore whatever response comes back from AD2. Is this even possible using stock IIS 7? Is there a middleware or something to allow this type of configuration on IIS 7? Would this be a job for some kind of middleware sitting between IIS and the AD domains?

  Read the article

• Creating Active Directory on an EC2 box

  - by Chiggins

  So I have Active Directory set up on a Windows Server 2008 Amazon EC2 server. Its set up correctly I think, I never got any errors with it. Just to test that I got it all set up correctly, I have a Windows 7 Professional virtual machine set up on my network to join to AD. I set the VM to use the Active Directory box as its DNS server. I type in my domain to join it, but I get the following error: DNS was successfully queried for the service location (SRV) resource record used to locate a domain controller for domain "ad.win.chigs.me": The query was for the SRV record for _ldap._tcp.dc._msdcs.ad.win.chigs.me The following domain controllers were identified by the query: ip-0af92ac4.ad.win.chigs.me However no domain controllers could be contacted. Common causes of this error include: - Host (A) or (AAAA) records that map the names of the domain controllers to their IP addresses are missing or contain incorrect addresses. - Domain controllers registered in DNS are not connected to the network or are not running. It seems that I can talk to Active Directory, but when I'm trying to contact the Domain Controller, its giving a private IP to connect to, at least thats what I can make out of it. Here are some nslookup results. > win.chigs.me Server: ec2-184-73-35-150.compute-1.amazonaws.com Address: 184.73.35.150 Non-authoritative answer: Name: ec2-184-73-35-150.compute-1.amazonaws.com Address: 10.249.42.196 Aliases: win.chigs.me > ad.win.chigs.me Server: ec2-184-73-35-150.compute-1.amazonaws.com Address: 184.73.35.150 Name: ad.win.chigs.me Address: 10.249.42.196 win.chigs.me and ad.win.chigs.me are CNAME's pointing to my EC2 box. Any idea what I need to do so that I can join my virtual machine to the EC2 Active Directory set up I have? Thanks!

  Read the article

• My system administrator set up 2 databases that sync. Master-Master. However, these two databases a

  - by Alex

  DB1 and DB2. I made changes to DB1, and it does not seem to be on DB2. When I do "SHOW SLAVE STATUS\G" on DB2, there seems to be an error: mysql> show slave status\G *************************** 1. row *************************** Slave_IO_State: Waiting for master to send event Master_Host: Master_User: Master_Port: Connect_Retry: 60 Master_Log_File: mysql-bin.0005496 Read_Master_Log_Pos: 5445649315 Relay_Log_File: mysqld-relay-bin.0041705 Relay_Log_Pos: 1624302119 Relay_Master_Log_File: mysql-bin.0004461 Slave_IO_Running: Yes Slave_SQL_Running: No Replicate_Do_DB: Replicate_Ignore_DB: Replicate_Do_Table: Replicate_Ignore_Table: Replicate_Wild_Do_Table: Replicate_Wild_Ignore_Table: Last_Errno: 1062 Last_Error: Error 'Duplicate entry '4779' for key 1' on query. Default database: 'falc'. Query: 'INSERT INTO `log` (`anon_id`, `created_at`, `query`, `episode_url`, `detail_id`, `ip`) VALUES ('fdzn1d45kMavF4qbyePv', '2009-11-19 04:19:13', 'amazon', '', '', '130.126.40.57')' Skip_Counter: 0 Exec_Master_Log_Pos: 162301982 Relay_Log_Space: 136505187184 Until_Condition: None Until_Log_File: Until_Log_Pos: 0 Master_SSL_Allowed: No Master_SSL_CA_File: Master_SSL_CA_Path: Master_SSL_Cert: Master_SSL_Cipher: Master_SSL_Key: Seconds_Behind_Master: NULL 1 row in set (0.00 sec) Then, I did show tables, and it seems like DB2 is lacking a table that I created on DB1...that means that for some reason, DB2 stopped syncing with DB1. How can I simply allow them to be in full synchronization again? All I want is DB2 to be exactly the same as DB1!

  Read the article

• dig lookup different from system lookup

  - by simao

  Hello, I am running dd-wrt and I configured it's dns server to resolve a few hosts inside my network. When I use dig to lookup these hosts, they are resolved OK, but when I try to ping those hosts I always receive an unknown host error message. For example: obe:~ simao$ dig dd-wrt ; <<>> DiG 9.6.0-APPLE-P2 <<>> dd-wrt ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 44026 ;; flags: qr aa rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;dd-wrt. IN A ;; ANSWER SECTION: dd-wrt. 0 IN A 192.168.1.1 But then: obe:~ simao$ ping dd-wrt ping: cannot resolve dd-wrt: Unknown host Any ideas? Thanks.

  Read the article

• OpenVPN - client-to-client traffic working in one direction but not the other

  - by user42055

  I have the following VPN configuration: +------------+ +------------+ +------------+ | outpost |----------------| kino |----------------| guchuko | +------------+ +------------+ +------------+ OS: FreeBSD 6.2 OS: Gentoo 2.6.32 OS: Gentoo 2.6.33.3 Keyname: client3 Keyname: server Keyname: client1 eth0: 10.0.1.254 eth0: 203.x.x.x eth0: 192.168.0.6 tun0: 192.168.150.18 tun0: 192.168.150.1 tun0: 192.168.150.10 P-t-P: 192.166.150.17 P-t-P: 192.168.150.2 P-t-P: 192.168.150.9 Kino is the server and has client-to-client enabled. All three machines have ip forwarding enabled, by this on the gentoo boxes: net.ipv4.conf.all.forwarding = 1 And this on the FreeBSD box: net.inet.ip.forwarding: 1 In the server's "ccd" directory is the following files: client1: iroute 192.168.0.0 255.255.255.0 client3: iroute 10.0.1.0 255.255.255.0 The server config has these routes configured: push "route 192.168.0.0 255.255.255.0" push "route 10.0.1.0 255.255.255.0" route 192.168.0.0 255.255.255.0 route 10.0.1.0 255.255.255.0 Kino's routing table looks like this: 192.168.150.0 192.168.150.2 255.255.255.0 UG 0 0 0 tun0 10.0.1.0 192.168.150.2 255.255.255.0 UG 0 0 0 tun0 192.168.0.0 192.168.150.2 255.255.255.0 UG 0 0 0 tun0 192.168.150.2 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 Outpost's like this: 192.168.150 192.168.150.17 UGS 0 17 tun0 192.168.0 192.168.150.17 UGS 0 2 tun0 192.168.150.17 192.168.150.18 UH 3 0 tun0 And Guchuko's like this: 192.168.150.0 192.168.150.9 255.255.255.0 UG 0 0 0 tun0 10.0.1.0 192.168.150.9 255.255.255.0 UG 0 0 0 tun0 192.168.150.9 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 Now, the tests. Pings from Guchuko to Outpost's LAN IP work OK, as does the reverse - pings from Outpost to Guchuko's LAN IP. However... Pings from Outpost, to a machine on Guchuko's LAN work fine: .(( root@outpost )). (( 06:39 PM )) :: ~ :: # ping 192.168.0.3 PING 192.168.0.3 (192.168.0.3): 56 data bytes 64 bytes from 192.168.0.3: icmp_seq=0 ttl=63 time=462.641 ms 64 bytes from 192.168.0.3: icmp_seq=1 ttl=63 time=557.909 ms But a ping from Guchuko, to a machine on Outpost's LAN does not: .(( root@guchuko )). (( 06:43 PM )) :: ~ :: # ping 10.0.1.253 PING 10.0.1.253 (10.0.1.253) 56(84) bytes of data. --- 10.0.1.253 ping statistics --- 3 packets transmitted, 0 received, 100% packet loss, time 2000ms Guchuko's tcpdump of tun0 shows: 18:46:27.716931 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 1, length 64 18:46:28.716715 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 2, length 64 18:46:29.716714 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 3, length 64 Outpost's tcpdump on tun0 shows: 18:44:00.333341 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 3, length 64 18:44:01.334073 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 4, length 64 18:44:02.331849 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 5, length 64 So Outpost is receiving the ICMP request destined for the machine on it's subnet, but appears not be forwarding it. Outpost has gateway_enable="YES" in its rc.conf which correctly sets net.inet.ip.forwarding to 1 as mentioned earlier. As far as I know, that's all that's required to make a FreeBSD box forward packets between interfaces. Is there something else I could be forgetting ?

  Read the article

• Substiting a line through PHP in SSH

  - by Asad Moeen

  I've already setup SSH usage in PHP and most of the things work. Now what I want to do is that I'm looking to edit a line in a file and replace it back. It works directly on the server but can't seem to get it working with PHP files. Here is what I'm trying. $new_line1 = 'Line $I want to add - The $I has to go into the file as it is'; $new_line2 = 'Ending $text of the line - $text again goes into file; $query = "Addition to line"; $exec1= 'cd /root; perl -pe "s/.*/' ; $exec2= '/ if $. == 37" Edit.sh > Edited.sh'; $new="$exec1$new_line1$query$new_line2$exec2"; $edit="cd /root/mp; cp Edited.sh Edit.sh"; echo $ssh->exec($new); echo $ssh->exec($edit); Now the thing is that running the perl command directly in SSH works without any errors but when I run this through PHP I get the error: Substitution replacement not terminated at -e line 1. I want to know why would it work this way and not that?

  Read the article

• CPU/JVM/JBoss 7 slows down over time

  - by lukas

  I'm experiencing performance slow down on JBoss 7.1.1 Final. I wrote simple program that demostrates this behavior. I generate an array of 100,000 of random integers and run bubble sort on it. @Model public class PerformanceTest { public void proceed() { long now = System.currentTimeMillis(); int[] arr = new int[100000]; for(int i = 0; i < arr.length; i++) { arr[i] = (int) (Math.random() * 200000); } long now2 = System.currentTimeMillis(); System.out.println((now2 - now) + "ms took to generate array"); now = System.currentTimeMillis(); bubbleSort(arr); now2 = System.currentTimeMillis(); System.out.println((now2 - now) + "ms took to bubblesort array"); } public void bubbleSort(int[] arr) { boolean swapped = true; int j = 0; int tmp; while (swapped) { swapped = false; j++; for (int i = 0; i < arr.length - j; i++) { if (arr[i] > arr[i + 1]) { tmp = arr[i]; arr[i] = arr[i + 1]; arr[i + 1] = tmp; swapped = true; } } } } } Just after I start the server, it takes approximately 22 seconds to run this code. After few days of JBoss 7.1.1. running, it takes 330 sec to run this code. In both cases, I launch the code when the CPU utilization is very low (say, 1%). Any ideas why? I run the server with following arguments: -Xms1280m -Xmx2048m -XX:MaxPermSize=2048m -Djava.net.preferIPv4Stack=true -Dorg.jboss.resolver.warning=true -Dsun.rmi.dgc.client.gcInterval=3600000 -Dsun.rmi.dgc.server.gcInterval=3600000 -Djboss.modules.system.pkgs=org.jboss.byteman -Djava.awt.headless=true -Duser.timezone=UTC -Djboss.server.default.config=standalone-full.xml -Xrunjdwp:transport=dt_socket,address=8787,server=y,suspend=n I'm running it on Linux 2.6.32-279.11.1.el6.x86_64 with java version "1.7.0_07". It's within J2EE applicaiton. I use CDI so I have a button on JSF page that will call method "proceed" on @RequestScoped component PerformanceTest. I deploy this as separate war file and even if I undeploy other applications, it doesn't change the performance. It's a virtual machine that is sharing CPUs with another machine but that one doesn't consume anything. Here's yet another observation: when the server is after fresh start and I run the bubble sort, It utilizes 100% of one processor core. It never switches to another core or drops utilization below 95%. However after some time the server is running and I'm experiencing the performance problems, the method above is utilizing CPU core usually 100%, however I just found out from htop that this task is being switched very often to other cores. That is, at the beginning it's running on core #1, after say 2 seconds it's running on #5 then after say 2 seconds #8 etc. Furthermore, the utilization is not kept at 100% at the core but sometimes drops to 80% or even lower. For the server after fresh start, even though If I simulate a load, it never switches the task to another core.

  Read the article

• How to move or delete files from a folder containing 2 million files on an NTFS drive?

  - by Beau

  The issue is that any modification to the directory locks up Explorer indefinitely, though Samba access to other directories still works. I've tried moving files locally and over Samba. Even enumerating the directory to get the list of files locks up the computer indefinitely. I tried using Python's win32file.FindFilesIterator to iterate the files but that also hangs. My idea was to move each file to a different directory (in a directory above the directory we're dealing with) based on its timestamp, so that we'd have at most a thousand or so files in each directory... But since I can't even enumerate the files, that's been a non-starter. If I have to give up and just nuke the directory I'm willing to do that, but a standard delete also hangs indefinitely. I have set these two parameters to increase speed and they also did not help the issue: R:\>fsutil behavior query disablelastaccess disablelastaccess = 1 R:\>fsutil behavior query disable8dot3 disable8dot3 = 1 These are all sequential images that would have run into the 'bug' with 8.3 filenames whereby many similarly named files in one directory can take a long time to compute 8.3 filenames. From what I understand this data is stored in the file system even after disable8dot3 is enabled, so it may still be contributing to the problem. Any ideas?

  Read the article

< Previous Page | 521 522 523 524 525 526 527 528 529 530 531 532  | Next Page >