Search Results

Search found 17686 results on 708 pages for 'high level'.

Page 527/708 | < Previous Page | 523 524 525 526 527 528 529 530 531 532 533 534  | Next Page >

• Cisco Catalyst 3750 connected to Cisco ASA 5505 and dropping packets

  - by Bo102010

  (Cross posted from Super User per suggestion there) At the office, I have inherited a network that I am still trying to fully comprehend. I have a problem today with a new connection between: A port on a Cisco Catalyst 3750 [WS-C3750G-48TS-S running C3750-IPSERVICESK9-M version 12.2(53)SE1] A port on a Cisco ASA 5505 [ASA Software version 8.3(2)] The 3750 is home to a Vlan that has a few ports assigned to it. interface Vlan3 description Internal network (172.18.160.0/24) ip address 172.18.160.1 255.255.255.0 I have a host (outside of my control) that needs to be in this VLAN (i.e it must have an address 172.18.160.something/24) that also needs to access the Internet. To accomplish this, I ran a link from the Catalyst (Gi1/0/13) to the ASA (Ethernet 0/5). I configured the Catalyst port like so: interface GigabitEthernet1/0/13 description To ASA, 172.18.160.69 switchport access vlan 3 switchport mode access speed 100 duplex full I configured the ASA like so: interface Vlan1 nameif inside security-level 100 ip address 172.18.160.69 255.255.255.0 interface Ethernet0/5 speed 100 duplex full Then I plugged the host into Ethernet 0/4 on the ASA and instructed its owner to make its default gateway 172.18.160.69. I made a NAT rule in the ASA and set up some rules, and it's able to access the Internet without issue. However, I noticed that the Catalyst reports a ton of packets being dropped toward the ASA. Catalyst3750#show interfaces GigabitEthernet 1/0/13 | include counters|drops Last clearing of "show interface" counters 00:28:13 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 136909347 This is a huge number of drops, since there's not much traffic on this VLAN at all. I tried these things: Make sure speed and duplex agree on both sides (100 Mbps / Full) Set no cdp enable on the Catalyst Gi10/13 Set no keepalive on the Catalyst Gi10/13 Checked for excessive CPU usage on both Checked for excessive traffic on both Am I missing something? Any help would be appreciated.

  Read the article

• Audio card with built-in ground isolator?

  - by Dave Jarvis

  What audio cards would you recommend that eliminate hum, and hard-drive & mouse movement signal interference? Hardware components: Motherboard. Asus P5Q SE Audio. Realtek ALC 1200, 8-Channel High-Definition Audio CODEC (on board) Harddrive. WD Caviar 320 GB Mouse. Logitech Marbleman USB Mixer. Mackie d.4 Pro Amplifier. Sonance Sonamp 260 All components are plugged into the same Monster Power HDP 910 powerbar (does not help eliminate noise). I have no other components plugged in. The computer uses a Monster iCable 1000 to go from mini (on board audio) to RCA (mixer). I have moved the cable as far from other cables as possible. A ground loop isolator between the mixer and on board audio eliminates all noise. I would rather not use a ground loop isolator; an internal audio card that is Linux-compatible (Kubuntu) would be ideal. Suggestions?

  Read the article

• Connect to Postgres remotely, open port 5432 for Postgres in iptables

  - by Victor

  I am trying to connect to Postgres remotely but I need to open port 5432 in iptables. My current iptables configuration is as follows: *filter # Allows all loopback (lo0) traffic and drop all traffic to 127/8 that doesn't use lo0 -A INPUT -i lo -j ACCEPT -A INPUT ! -i lo -d 127.0.0.0/8 -j REJECT # Accepts all established inbound connections -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT # Allows all outbound traffic # You can modify this to only allow certain traffic -A OUTPUT -j ACCEPT # Allows HTTP and HTTPS connections from anywhere (the normal ports for websites) -A INPUT -p tcp --dport 80 -j ACCEPT -A INPUT -p tcp --dport 443 -j ACCEPT # Allows SSH connections # # THE -dport NUMBER IS THE SAME ONE YOU SET UP IN THE SSHD_CONFIG FILE # -A INPUT -p tcp -m state --state NEW --dport 30000 -j ACCEPT # Allow ping -A INPUT -p icmp -m icmp --icmp-type 8 -j ACCEPT # log iptables denied calls -A INPUT -m limit --limit 5/min -j LOG --log-prefix "iptables denied: " --log-level 7 # Reject all other inbound - default deny unless explicitly allowed policy -A INPUT -j REJECT -A FORWARD -j REJECT COMMIT What would I have to add in iptables to open the port? I'm trying to install phppgadmin on a different server to access the postgres database. Thank you.

  Read the article

• New AD-DC in a new Site is refusing cross-site IPv4 connections

  - by sysadmin1138

  We just added a new Server 2008 (sp2) Domain Controller in a new Site, our first such config. It's over a VPN gateway WAN (10Mbit). Unfortunately it is displaying a strange network symptom. Connections to the SMB ports (TCP/139 and TCP/445) are being actively refused... if the connection is coming in on pure IPv4. If the incoming connection is coming by way of the 6to4 tunnel those connections establish and work just fine. It isn't the Firewall, since this behavior can be replicated with the firewall turned off. Also, it's actually issuing RST packets to connection attempts; something that only happens with a Windows Firewall if there is a service behind a port and the service itself denies access. I doubt it's some firewall device on the wire, since the server this one replaced was running Samba and access to it from our main network functioned just fine. I'm thinking it might have something to do with the Subnet lists in AD Sites & Services, but I'm not sure. We haven't put any IPv6 addresses in there, just v4, and it's the v4 connections that are being denied. Unfortunately, I can't figure this out. We need to be able to talk to this DC from the main campus. Is there some kind of site-based SMB-level filtering going on? I can talk to the DC's on campus just fine, but that's over that v6 tunnel. I don't have access to a regular machine on that remote subnet, which limits my ability to test.

  Read the article

• restoring a failed SBS 2000 box...

  - by Brad Pears

  Hi there, I read a post where you had mentioned you have had a PERC card blow up on you in an SBS box... I've got a similar situation where one of my RAID drives failed and then the power supply failed before I could replace the drive... I then replaced the power supply and the failed drive and reconfigured the RAID array. I had a recent full backup of the my Win2k SBS's C: drive stored on my SYmantec backup exec server so I installed win2K server on the c: partition and then once I had that up and running, installed the backup exec agent so as to do a restore of the entire c drive including system state. THis all worked just fine, until I had to reboot. I received an "incorrect drive configuration" error and then it hangs. I figure that likely makes sense becasue I think my RAID array is configured slightly different now in that the partitions may be sizeded ever so slightly differently now than they were before I think... Is there a way I can just restore from my backup BUT maybe exclude some of the registry and hidden boot files it wants to restore so that it is booting with the current configuration now active on that machine - not the pre blow up configuration files? I also read a post that indicated you might have to install the exact same service pack etc... etc.. before attemting a restore but that does not make sense to me being as the entire c drive contents are going to be overwritten by the restore anyway? THe basic OS install is just to be able to get the backup exec agent installed . I can;t understand why one would need to install the exact same SP level. CAn you shed some light on what I might be able to do to get this thing up and running? Thanks,Brad

  Read the article

• nginx reverse ssl proxy with multiple subdomains

  - by BrianM

  I'm trying to locate a high level configuration example for my current situation. We have a wildcard SSL certificate for multiple subdomains which are on several internal IIS servers. site1.example.com (X.X.X.194) -> IISServer01:8081 site2.example.com (X.X.X.194) -> IISServer01:8082 site3.example.com (X.X.X.194) -> IISServer02:8083 I am looking to handle the incoming SSL traffic through one server entry and then pass on the specific domain to the internal IIS application. It seems I have 2 options: Code a location section for each subdomain (seems messy from the examples I have found) Forward the unencrypted traffic back to the same nginx server configured with different server entries for each subdomain hostname. (At least this appears to be an option). My ultimate goal is to consolidate much of our SSL traffic to go through nginx so we can use HAProxy to load balance servers. Will approach #2 work within nginx if I properly setup the proxy_set_header entries? I envision something along the lines of this within my final config file (using approach #2): server { listen Y.Y.Y.174:443; #Internally routed IP address server_name *.example.com; proxy_pass http://Y.Y.Y.174:8081; } server { listen Y.Y.Y.174:8081; server_name site1.example.com; -- NORMAL CONFIG ENTRIES -- proxy_pass http://IISServer01:8081; } server { listen Y.Y.Y.174:8081; server_name site2.example.com; -- NORMAL CONFIG ENTRIES -- proxy_pass http://IISServer01:8082; } server { listen Y.Y.Y.174:8081; server_name site3.example.com; -- NORMAL CONFIG ENTRIES -- proxy_pass http://IISServer02:8083; } This seems like a way, but I'm not sure if it's the best way. Am I missing a simpler approach to this?

  Read the article

• LASER x Deskjet Printer

  - by Mike

  I am about to buy a color printer. I had a b&W laserjet printer in the past but since then I use deskjet for decades. I need a printer that can deliver high quality as these photo deskjet printers but I am tired of paying ink that costs $9,000 per gallon of ink (1 gallon = 3.785 liters = 300 cartridges = $9,000). So, I was pondering about buying a color laser, but I am not sure if these printers can deliver the same quality and worth the investment in terms of toner consumption. I remembered that my old laserjet printer was able to print 1100 pages per toner cartridge. The deskjet printers I have can print 500 pages per cartridge. Price by price, 2 deskjet cartridges have more or less the same cost as one toner cartridge and in theory prints almost the same. I am not sure if this is true for color lasers. What you guys can tell me about quality, toner cost and cost per page using laser or deskjet. Does it worths the change? Remember that a deskjet printer costs $50 and a laser printer costs $200. thanks.

  Read the article

• What could cause a huge packet loss in Ubuntu 9.10, for both wired and wireless?

  - by xzenox

  I was previously using 9.04 fine (and in fact, I am posting this from my old 9.04 live cd). I tested the following install steps in a virtualbox vm prior to following the sames ones to upgrade my laptop: Download/burn ubuntu minimal cd (12mb one) Install ubuntu minimal sudo apt-get update sudo apt-get upgrade sudo apt-get ubuntu-desktop ubuntu-standard In the VM worked fine and I found myself with a working 9.10 ubuntu, network worked fine and I was able to test my backups and DropBox without a hitch (host was 9.04). When I followed the same steps on my laptop, everything worked up to after 9.10 being installed and working. As far as I can tell, everything besides eth0/wireless works. For some reason, I am unable to access the internet. Ping reports that over 99% of packets get lost (over an hour or so of pinging). This means for example that if I try hard enough, I can load a webpage but only at the cost of much patience... This happens both for a wired and wireless connection to my wrt310n (updated with latest firmware). At first I thought that it could be related to the ipv6 issues ppl have been experiencing however even after disabling ipv6 at the kernel level (through grub), I still get the issue. I do not think this is related to DNS issues or the likes since even when I ping my ISP's gateway IP, I have the same amount of packet loss. No DNS resolving should be required there. Access to my router works peachy with no packet loss there. I've tried different MTU values but to no avail. Note that this issue affects every web-enabled application: firefox, ping, synaptic, etc. The same hardware/router combo works with 9.04 but not with 9.10. In fact, when I did: sudo apt-get ubuntu-desktop ubuntu-standard after 9.10 minimal was installed, it downloaded over 400mb of packages without a hitch so my guess is that one of those packages either in ubuntu-desktop or ubuntu-standard is causing havok. Thoughts?

  Read the article

• How to troubleshoot connectivity when curl gets an *empty response*

  - by chad

  I want to know how to proceed in troubleshooting why a curl request to a webserver doesn't work. I'm not looking for help that would be dependent upon my environment, I just want to know how to collect information about exactly what part of the communication is failing, port numbers, etc. chad-integration:~ # curl -v 111.222.159.30 * About to connect() to 111.222.159.30 port 80 (#0) * Trying 111.222.159.30... connected * Connected to 111.222.159.30 (111.222.159.30) port 80 (#0) > GET / HTTP/1.1 > User-Agent: curl/7.19.0 (x86_64-suse-linux-gnu) libcurl/7.19.0 OpenSSL/0.9.8h zlib/1.2.3 libidn/1.10 > Host: 111.222.159.30 > Accept: */* > * Empty reply from server * Connection #0 to host 111.222.159.30 left intact curl: (52) Empty reply from server * Closing connection #0 So, I understand that an empty response means that curl didn't get any response from the server. No problem, that's precisely what I'm trying to figure out. But what more specific info can I derive from cURL here? It was able to successfully "connect", so doesn't that involve some bidirectional communication? If so, then why does the response not come also? Note, I've verified my service is up and returning responses. Note, I'm a bit green at this level of networking, so feel free to provide some general orientation material.

  Read the article

• Linking to network shares from Sharepoint pages

  - by Russell C

  So the place I work decided to set up a Microsoft Sharepoint 2010 server for task management and I (as the lowly entry-level intern) have been tasked with "figuring it out." One thing that the end users really, really, really, want is the ability to link to network shares (that are readable by anyone who will be using sharepoint) from a Sharepoint web page. In order to do this, I have edited the HTML manually with several lines that look like the following: <a href="file://server/share">Server Share</a> This works (sometimes) but the link reported by Sharepoint is often wrong and editing pages that contain these links will mangle the code such that when I open it, the code no longer looks like what it did when I last hit save (breaking all those links). Obviously this is not sustainable. I've been told by coworkers that "It worked that way at the last place I worked" but I haven't found out how yet. Any ideas on how this would work or am I barking up the wrong tree? None of the knowledge searches I've done shed any light on the sitataion. Thanks for any help! -Russell P.S. It should be noted that the file option in an href tag ONLY works in IE (which is a real bummer since we mostly use Firefox).

  Read the article

• 502: proxy: pass request body failed

  - by Andrei Serdeliuc

  Sometimes I get the following error (in apache's error.log) when viewing my site over https: (502)Unknown error 502: proxy: pass request body failed to xxx.xxx.xxx.xxx:443 I'm not entirely sure what this is and why it happens, it's also not consistent. The request route is: Browser Proxy server (apache with mod_proxy + mod_ssl) Load balancer (aws) Web server (apache with mod_ssl) The configuration on the proxy server is as follows: <VirtualHost *:443> ProxyRequests Off ProxyVia On ServerName www.xxx.co.uk ServerAlias xxx.co.uk <Directory proxy:*> Order deny,allow Allow from all </Directory> <Proxy *> AddDefaultCharset off Order deny,allow Allow from all </Proxy> ProxyPass / balancer://cluster:443/ lbmethod=byrequests ProxyPassReverse / balancer://cluster:443/ ProxyPreserveHost off SSLProxyEngine On SSLEngine on SSLCipherSuite ALL:!ADH:!EXPORT56:RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv2:+EXP:+eNULL SSLCertificateFile /var/www/vhosts/xxx/ssl/www.xxx.co.uk.cert SSLCertificateKeyFile /var/www/vhosts/xxx/ssl/www.xxx.co.uk.key <Proxy balancer://cluster> BalancerMember https://xxx.eu-west-1.elb.amazonaws.com </Proxy> </VirtualHost> Any idea what the issue might be?

  Read the article

• LSI 9260-8i w/ 6 256gb SSDs - RAID 5, 6, 10, or bad idea overall?

  - by Michael Pearson

  We're provisioning a new production server for our reasonably busy website. Our choice of host have available a 6 drive configuration with a LSI 9260-8i card. My initial thought was to fill all six bays with SSDs (Intel 520 256gb) and set them up in RAID. Good, bad, or terrible idea? Can the card handle it? Should we be using RAID 5, 6 or 10? This would be the first time the provider have filled all six slots for this rackmount with SSDs, so they're a bit hesitant. I'm wondering if somebody else with this card has done something similar in a production environment. We do about 43gb of writes per day and currently use about 300gb of storage. The server acts as webserver, database, and image store for approx 1 million files. The plan is to underprovision the SSDs by approximately 10% to 20% to increase their overall lifespan & performance. The fallback option is 2x480gb SSDs in RAID 1 and another 2x1TB HDDs in RAID 1. The motivation behind this is that the server rental cost difference between 2xSSDs and 6xSSDs is minimal (compared to the overall cost of the rental). We do not have any special high-IOPs requirements. However, if the configuration is known to work, I don't see a good reason to not use it and not have to worry about having separate 'fast and small' and 'slow and large' disks.

  Read the article

• How can I debug user mode driver failures in Windows 8

  - by Tom

  I have a 32 GB SD Card. Whenever I insert this card in to my newly upgraded Windows 8 laptop the OS stops responding normally. Metro Apps won't work. The system may or may not log in. Desktop apps may or may not be able to do things. When I remove the card and restart then all is fine. As soon as I put the card back in, the system starts misbehaving again. I've run Windows Update, so I have the latest drivers from Microsoft. This does not occur with the 8 GB cards I have. Unfortunately I only have one 32 GB card, so I can't test with others. From examining the system event log I've determined this is happening due to a user mode driver failure. How can I best debug this issue from here? How can I figure out which driver this is related to? Will there be a Dr. Watson crash dump somewhere? Details - System - Provider [ Name] Microsoft-Windows-DriverFrameworks-UserMode [ Guid] {2E35AAEB-857F-4BEB-A418-2E6C0E54D988} EventID 10110 Version 1 Level 1 Task 64 Opcode 0 Keywords 0x2000000000000000 - TimeCreated [ SystemTime] 2012-10-29T00:51:57.532718300Z EventRecordID 40417 Correlation - Execution [ ProcessID] 1056 [ ThreadID] 3796 Channel System Computer thebrain - Security [ UserID] S-1-5-18 - UserData - UMDFHostProblem [ lifetime] {811E3DC4-FBC6-420B-ABCC-AD7505A36F3B} - Problem [ code] 3 [ detectedBy] 2 ExitCode 3 - Operation [ code] 259 Message 72448 Status 4294967295 Edit 1 So I tried using Debug View from SysInternals (you can get it here: http://technet.microsoft.com/en-us/sysinternals/bb896647.aspx). That gave me this information: which is not especially helpful. Then I tried connecting WinDbg to WUDFHost.exe (the process that seems to host user mode drivers) to see if it could catch the error. Get it here: http://msdn.microsoft.com/en-US/windows/hardware/hh852363 Instructions: http://msdn.microsoft.com/en-US/library/windows/hardware/ff554716(v=vs.85).aspx That didn't help much. It didn't catch any exceptions as I'd hoped (which would point me to the cause of the crash at least). Here's the stack of one of the threads:

  Read the article

• How to let MSN or Yahoo Messenger set you to be Invisible or Offline when you are idle for an hour?

  - by Jian Lin

  The short question is: How do we let MSN or Yahoo Messenger set us to be Invisible or Offline when we are idle for half an hour or an hour? The reason is: if I am on 24 hours a day, some people see me as weird. Some people see my value as low, because I am always there. There are ways to set me to "Away" or "Busy" after 10 minutes, but there seems to be no way to set myself to invisible or offline after 1 hour. As I am a software developer, I am very used to turning the computer on 24 hours a day. (for example, for checking email for urgent fixes, and fix issue and push to web server). We don't turn off computer usually even when we sleep, because we may sometimes can't sleep yet and come check on the computer, or wake up in the morning and immediately need to check if everything is ok. But, my MSN and Yahoo Messenger is always on for 24 hours a day, and I found that some girls start to ask me why I am always there 24 hours a day (even though they see me as away or busy, their feeling is that I am always there). What's more, I found that since I am always there, my value actually drop in their eyes, because hard to get = high value, and always there = low value. Some people feel me as having nothing much to do, always in front of computer, or what is he doing in front of computer so much? Now since it is my job, and I need to read emails once in a while, I am in fact in front of the computer more than some other people. I am in front of the computer maybe 10 hours a day, far from 24 hours a day. Is there an easy and automatic solution to this?

  Read the article

• Fetch videos from sony handycam to linux

  - by bstpierre

  I've got a Sony Handycam DCR-DVD101. When I plug connect the USB cable to my laptop (Ubuntu 10) it doesn't mount any storage device. If I run usb-devices, I see: T: Bus=02 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 6 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=054c ProdID=00c1 Rev=01.00 S: Manufacturer=SONY S: Product=Storage Device C: #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=2mA I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=05 Prot=50 Driver=usb-storage The driver says usb-storage, but I'm not sure how to get the device mounted. Is there a way to make this work? Update: checking dmesg, I see: [259072.576559] usb 2-1.1: new high speed USB device using ehci_hcd and address 6 [259072.687200] usb 2-1.1: configuration #1 chosen from 1 choice [259072.836188] Initializing USB Mass Storage driver... [259072.836476] scsi5 : SCSI emulation for USB Mass Storage devices [259072.836632] usb-storage: device found at 6 [259072.836636] usb-storage: waiting for device to settle before scanning [259072.836660] usbcore: registered new interface driver usb-storage [259072.836666] USB Mass Storage support registered. [259077.830410] usb-storage: device scan complete [259077.832343] scsi 5:0:0:0: CD-ROM SONY DDX-A1010 R1.0 PQ: 0 ANSI: 0 [259077.888167] sr1: scsi3-mmc drive: 0x/0x pop-up [259077.888446] sr 5:0:0:0: Attached scsi CD-ROM sr1 [259077.888593] sr 5:0:0:0: Attached scsi generic sg2 type 5 [259080.002079] sr 5:0:0:0: [sr1] Unhandled sense code [259080.002085] sr 5:0:0:0: [sr1] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [259080.002091] sr 5:0:0:0: [sr1] Sense Key : Blank Check [current] [259080.002097] sr 5:0:0:0: [sr1] Add. Sense: No additional sense information [259080.002104] sr 5:0:0:0: [sr1] CDB: Read(10): 28 00 00 00 00 00 00 00 02 00 00 00 [259080.002117] end_request: I/O error, dev sr1, sector 0 [259080.002123] Buffer I/O error on device sr1, logical block 0 [259080.002128] Buffer I/O error on device sr1, logical block 1 Those I/O errors don't look good, is there any hope?

  Read the article

• Password Policy seems to be ignored for new Domain on Windows Server 2008 R2

  - by Earl Sven

  I have set up a new Windows Server 2008 R2 domain controller, and have attempted to configure the Default Domain Policy to permit all types of passwords. When I want to create a new user (just a normal user) in the Domain Users and Computers application, I am prevented from doing so because of password complexity/length reasons. The password policy options configured in the Default Domain Policy are not defined in the Default Domain Controllers Policy, but having run the Group Policy Modelling Wizard these settings do not appear to be set for the Domain Controllers OU, should they not be inherited from the Default Domain policy? Additionally, if I link the Default Domain policy to the Domain Controllers OU, the Group Policy Modelling Wizard indicates the expected values for complexity etc, but I still cannot create a new user with my desired password. The domain is running at the Windows Server 2008 R2 functional level. Any thoughts? Thanks! Update: Here is the "Account policy/Password policy" Section from the GPM Wizard: Policy Value Winning GPO Enforce password history 0 Passwords Remembered Default Domain Policy Maximum password age 0 days Default Domain Policy Minimum password age 0 days Default Domain Policy Minimum password length 0 characters Default Domain Policy Passwords must meet complexity Disabled Default Domain Policy These results were taken from running the GPM Wizard at the Domain Controllers OU. I have typed them out by hand as the system I am working on is standalone, this is why the table is not exactly the wording from the Wizard. Are there any other policies that could override the above? Thanks!

  Read the article

• KVM network bridge with two NICs

  - by Eil

  Greetings, I'm trying to set up bridged networking with KVM and am getting nowhere. There are docs and tutorials on the subject, but they all seem to conflict or don't provide enough info. I was wondering if someone can give me a high-level overview of how to get this working. I can probably work out the details myself (configuring the interfaces, adding routes, etc), I just need help on the big picture: how everything is interconnected. I have a RHEL5 server with KVM installed and running. It has two physical NICs, eth0 and eth1 in the same VLAN. I would like to use eth1 for all traffic between the guests and the rest of the network and reserve eth0 for host management, guest migrations, etc if possible. I'm not picky about which one gets the default route, although it would be nice if we could make it eth0. All of the guests will have static IPs. I would prefer that when a new guest is added, the networking configuration only needs to be set from within the guest itself. Basically, I want this: eth0: all host traffic eth1: all guest traffic Open to any other suggestions if this isn't possible or will be kludgy/difficult. Pointers to existing documentation might not be helpful since I've already been though just about everything out there. Thanks for any help.

  Read the article

• cPanel web server redundancy advice?

  - by crgnz

  At present I operate a (reasonably low volume) web-hosting service with a Centos 5.3 server running cPanel/WHM. I would like to implement a level of redundancy such that in the event of server failure, I can restore service with a minimum of effort in less than 60 minutes. I also want to setup a secondary DNS that cPanel will replicate with. My current idea is to kill two birds with one stone by: My current server is called "www1" Purchase an identical server (HP DL360 G4) with mirrored disks. Call this server "www2" Install Centos 5.4 (or perhaps I should install 5.3 to be identical with www1) Install cPanel/WHM on this server and fully license it Setup www1 and www2 cPanel to replicate DNS with each other Setup a nightly replication script that does the following: a) rsync's the /home directory from www1 to www2 b) dumps all MySQL databases on www1 and copies them to a temp folder (with root access only) on www2 c) triggers a script to run on www2 that restores the MySQL dumps Thus each night a fully working copy of all the websites and MySQL databases is copied to www2. I do not have enough knowledge of MySQL replication to understand if it works safely and transparently with cPanel. Thus I propose the mysql dump/copy/restore due to not knowing any better! In the event that www1 dies a horrible death, I envisage that I could login to www2, change the IP addresses to those that www1 had, and presto, the websites are available again. The advantage of this idea is that it is fairly simple and "low tech" and thus does not require an expert sysadmin to setup and monitor (I am NOT an expert sysadmin) The disadvantage of this idea is that up to a full days worth of data changes would be lost. I think this would be acceptable to the sorts of customers I host at the moment. The other disadvantage would be having to pay for a full cPanel license, but I am comfortable with that cost, so for now all I want to discuss are technical considerations. Is this a sound scheme?

  Read the article

• Re-configure Office 2007 installation unattended: Advertised components --> Local

  - by abstrask

  On our Citrix farm, I just found out that some sub-components are "Installed on 1st Use" (Advertised), which does play well on terminal servers. Not only that, but you also get a rather non-descriptive error message, when a document tried to use a component, which is "Installed on 1st Use" (described on Plan to deploy Office 2010 in a Remote Desktop Services environment): Microsoft Office cannot run this add-in. An error occurred and this feature is no longer functioning correctly. Please contact your system administrator. I have ~50 Citrix servers where I need to change the installation state of all Advertised components to Local, so I created an XML file like this: <?xml version="1.0" encoding="utf-8"?> <Configuration Product="ProPlus"> <Display Level="none" CompletionNotice="no" SuppressModal="yes" AcceptEula="yes" /> <Logging Type="standard" Path="C:\InstallLogs" Template="MS Office 2007 Install on 1st Use(*).log" /> <Option Id="AccessWizards" State="Local" /> <Option Id="DeveloperWizards" State="Local" /> <Setting Id="Reboot" Value="NEVER" /> </Configuration> I run it with a command like this (using the appropriate paths): "[..]\setup.exe" /config ProPlus /config "[..]\Install1stUse-to-Forced.xml" According to the log file, the syntax appears to be accepted and the config file parsed: Parsing command line. Config XML file specified: [..]\Install1stUse-to-Forced.xml Modify requested for product: PROPLUS Parsing config.xml at: [..]\Install1stUse-to-Forced.xml Preferred product specified in config.xml to be: PROPLUS But the "Final Option Tree" still reads: Final Option Tree: AlwaysInstalled:local Gimme_OnDemandData:local ProductFiles:local VSCommonPIAHidden:local dummy_MSCOMCTL_PIA:local dummy_Office_PIA:local ACCESSFiles:local ... AccessWizards:advertised DeveloperWizards:advertised ... And the components remain "Advertised". Just to see if the installation state is overridden in another XML file, I ran: findstr /l /s /i "AccessWizards" *.xml Against both my installation source and "%ProgramFiles%\Common Files\Microsoft Shared\OFFICE12\Office Setup Controller", but just found DefaultState to be "Local". What am I doing wrong? Thanks!

  Read the article

• Updated XAMPP with MySQL, all my tables are missing

  - by user371699

  I just updated XAMPP to a newer version, which included updating MySQL from 5.5 to 5.6. Using phpMyAdmin, however, all of my tables within my databases still appear on the left navigation panel, but the main window shows that all my databases are empty (except for information_schema, and a couple other default tables.) Clicking on a table in the navigation panel gives me a "table doesn't exist" message. It does looks like information_schema.tables doesn't have my tables, either. Can anyone assist me with this? I did make a complete backup of all my databases before the upgrade, but I first want to see if I can fix this the "normal" way. Furthermore, I'm not sure if the MySQL upgrade involved making changes to the information/performance databases, so I don't know if I can restore the old ones. Thank you. EDIT: Continuing my searching, I realized that only the INNODB databases are missing. I've tried running the following with no avail: /opt/lampp/bin $ sudo ./mysql_install_db --basedir=/opt/lampp and /opt/lampp/bin $ sudo ./mysql_install_db --basedir=/opt/lampp --datadir=/opt/lampp/var/mysql The my.cnf file in /opt/lampp/etc contains the following InnoDB settings: innodb_data_home_dir = /opt/lampp/var/mysql/ innodb_data_file_path = ibdata1:10M:autoextend innodb_log_group_home_dir = /opt/lampp/var/mysql/ # You can set .._buffer_pool_size up to 50 - 80 % # of RAM but beware of setting memory usage too high innodb_buffer_pool_size = 16M # Deprecated in 5.6 #innodb_additional_mem_pool_size = 2M # Set .._log_file_size to 25 % of buffer pool size innodb_log_file_size = 5M innodb_log_buffer_size = 8M innodb_flush_log_at_trx_commit = 1 innodb_lock_wait_timeout = 50 What could possibly be wrong? Why is the information_schema not updating correctly? It looks like /opt/lampp/var/mysql has all my tables in it within the database directories, but they're still not showing up in information_schema.

  Read the article

• RemoteApp .rdp embed creds?

  - by Chris_K

  Windows 2008 R2 server running Remote Desktop Services (what we used to call Terminal Services back in the olden days). This server is the entry point into a hosted application -- you could call it Software as a Service I suppose. We have 3rd party clients connecting to use it. Using RemoteApp Manager to build RemoteApp .rdp shortcuts to distribute to client workstations. These workstations are not in the same domain as the RDS server. There is no trust relationship between domains (nor will there be). There is a tightly controlled site to site VPN between workstations and the RDS server, we're quite confident we have access to the server locked down. The remoteApp being run is an ERP application with its own authentication scheme. The issue? I'm trying to avoid the need to create AD logins for every end user when connecting to the RemoteApp server. In fact, since we're doing a remoteApp and they have to authenticate to that app, I'd rather just not prompt them at all for AD creds. I certainly don't want them caught up in managing AD passwords (and periodic expirations) for accounts they only use to get to their ERP login. However, I can't figure out how to embed AD creds in a RemoteApp .rdp file. I don't really want to turn off all authentication on the RDS server at that level. Any good options? My goal is to make this as seamless as possible for the end-users. Clarifying questions are welcome.

  Read the article

• How to set the VirtualDocumentRoot based on the files within

  - by Chuck Vose

  I'm trying to set up Apache to use the VirtualDocumentRoot directive but my sites aren't all exactly the same. Most of the sites have a drupal folder which should be the root but there are a few really old drupal sites, a few rails sites, some django sites, etc. that want the Document root to be / or some other folder. Is there a way to set up VirtualDocumentRoot based on a conditional or is there a way to use RewriteRule/Cond to detect that / is the incorrect folder if there is a drupal folder or a public folder? Here's what I have so far: <VirtualHost *:80> # Wildcard ServerAlias, this is the default vhost if no specific vhost matches first. ServerAlias *.unicorn.devserver.com # Automatic ServerName, based on the HTTP_HOST header. UseCanonicalName Off # Automatic DocumentRoot. This uses the 4th level domain name as the document root, # for example http://bar.foo.baz.com/ would respond with /Users/vosechu/Sites/bar/drupal. VirtualDocumentRoot /Users/vosechu/Sites/%-4/drupal </VirtualHost> Thanks in advance! -Chuck

  Read the article

• Body of email breaks distribution list in exchange?

  - by widgisoft

  Hi, I have a very odd problem that I'm not sure is a programming issue or a server issue :-p. Basically I'm sending an email to an exchange distribution list that includes a PHP stack trace; during certain faults the trace includes really high level information such as the machine's environment variables (during file reads, etc.). I went through a copy of the email line by line until the email sent and it appears the line: [SUDO_COMMAND] => /etc/init.d/httpd restart is the culprit. Adding a string replacement in before the email is sent allows a successful send. What I don't understand is WHY these stream of characters are causing the issue ONLY on the distribution email. If I send the email to myself as well, i.e. "[email protected]; [email protected]", then I get the email fine. Re-ordering the list doesn't make a difference the group never gets the email. Because the individual gets the email and not the group I'm assuming the fault is with exchange and some rogue filtering - I've gone through it with the sysadmins and there's no filtering of any sort on that group... so maybe it's a bug? I can't find anyone else having recorded this specific fault so I figured I'd open it here. For now I'm just not using the distribution list but it'd be nice to eventually find the solution. Many thanks, Chris

  Read the article

• Redundant OpenVPN connections with advanced Linux routing over an unreliable network

  - by konrad

  I am currently living in a country that blocks many websites and has unreliable network connections to the outside world. I have two OpenVPN endpoints (say: vpn1 and vpn2) on Linux servers that I use to circumvent the firewall. I have full access to these servers. This works quite well, except for the high package loss on my VPN connections. This packet loss varies between 1% and 30% depending on time and seems to have a low correlation, most of the time it seems random. I am thinking about setting up a home router (also on Linux) that maintains OpenVPN connections to both endpoints and sends all packets twice, to both endpoints. vpn2 would send all packets from home to vpn1. Return trafic would be send both directly from vpn1 to home, and also through vpn2. +------------+ | home | +------------+ | | | OpenVPN | | links | | | ~~~~~~~~~~~~~~~~~~ unreliable connection | | +----------+ +----------+ | vpn1 |---| vpn2 | +----------+ +----------+ | +------------+ | HTTP proxy | +------------+ | (internet) For clarity: all packets between home and the HTTP proxy will be duplicated and sent over different paths, to increase the chances one of them will arrive. If both arrive, the first second one can be silently discarded. Bandwidth usage is not an issue, both on the home side and endpoint side. vpn1 and vpn2 are close to each other (3ms ping) and have a reliable connection. Any pointers on how this could be achieved using the advanced routing policies available in Linux?

  Read the article

• Find out which task is generating a lot of context switches on linux

  - by Gaks

  According to vmstat, my Linux server (2xCore2 Duo 2.5 GHz) is constantly doing around 20k context switches per second. # vmstat 3 procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 2 0 7292 249472 82340 2291972 0 0 0 0 0 0 7 13 79 0 0 0 7292 251808 82344 2291968 0 0 0 184 24 20090 1 1 99 0 0 0 7292 251876 82344 2291968 0 0 0 83 17 20157 1 0 99 0 0 0 7292 251876 82344 2291968 0 0 0 73 12 20116 1 0 99 0 ... but uptime shows small load: load average: 0.01, 0.02, 0.01 and top doesn't show any process with high %CPU usage. How do I find out what exactly is generating those context switches? Which process/thread? I tried to analyze pidstat output: # pidstat -w 10 1 12:39:13 PID cswch/s nvcswch/s Command 12:39:23 1 0.20 0.00 init 12:39:23 4 0.20 0.00 ksoftirqd/0 12:39:23 7 1.60 0.00 events/0 12:39:23 8 1.50 0.00 events/1 12:39:23 89 0.50 0.00 kblockd/0 12:39:23 90 0.30 0.00 kblockd/1 12:39:23 995 0.40 0.00 kirqd 12:39:23 997 0.60 0.00 kjournald 12:39:23 1146 0.20 0.00 svscan 12:39:23 2162 5.00 0.00 kjournald 12:39:23 2526 0.20 2.00 postgres 12:39:23 2530 1.00 0.30 postgres 12:39:23 2534 5.00 3.20 postgres 12:39:23 2536 1.40 1.70 postgres 12:39:23 12061 10.59 0.90 postgres 12:39:23 14442 1.50 2.20 postgres 12:39:23 15416 0.20 0.00 monitor 12:39:23 17289 0.10 0.00 syslogd 12:39:23 21776 0.40 0.30 postgres 12:39:23 23638 0.10 0.00 screen 12:39:23 25153 1.00 0.00 sshd 12:39:23 25185 86.61 0.00 daemon1 12:39:23 25190 12.19 35.86 postgres 12:39:23 25295 2.00 0.00 screen 12:39:23 25743 9.99 0.00 daemon2 12:39:23 25747 1.10 3.00 postgres 12:39:23 26968 5.09 0.80 postgres 12:39:23 26969 5.00 0.00 postgres 12:39:23 26970 1.10 0.20 postgres 12:39:23 26971 17.98 1.80 postgres 12:39:23 27607 0.90 0.40 postgres 12:39:23 29338 4.30 0.00 screen 12:39:23 31247 4.10 23.58 postgres 12:39:23 31249 82.92 34.77 postgres 12:39:23 31484 0.20 0.00 pdflush 12:39:23 32097 0.10 0.00 pidstat Looks like some postgresql tasks are doing 10 context swiches per second, but it doesn't all sum up to 20k anyway. Any idea how to dig a little deeper for an answer?

  Read the article

< Previous Page | 523 524 525 526 527 528 529 530 531 532 533 534  | Next Page >