Search Results

Search found 34341 results on 1374 pages for 'link local'.

Page 527/1374 | < Previous Page | 523 524 525 526 527 528 529 530 531 532 533 534  | Next Page >

  • radvd is not assigning prefix

    - by Samik
    I'm currently trying to setup IPv6 address auto-configuration with router advertisement daemon (radvd) on a virtual machine running CentOS 6.5. But the eth0 interface is not obtaining that prefix. I've obtained the ULA prefix from here. Contents of /etc/sysctl.conf # Kernel sysctl configuration file for Red Hat Linux # # For binary values, 0 is disabled, 1 is enabled. See sysctl(8) and # sysctl.conf(5) for more details. # Controls IP packet forwarding net.ipv4.ip_forward = 0 net.ipv6.conf.all.forwarding = 1 # Controls source route verification net.ipv4.conf.default.rp_filter = 1 # Do not accept source routing net.ipv4.conf.default.accept_source_route = 0 # Controls the System Request debugging functionality of the kernel kernel.sysrq = 0 # Controls whether core dumps will append the PID to the core filename. # Useful for debugging multi-threaded applications. kernel.core_uses_pid = 1 # Controls the use of TCP syncookies net.ipv4.tcp_syncookies = 1 # Disable netfilter on bridges. net.bridge.bridge-nf-call-ip6tables = 0 net.bridge.bridge-nf-call-iptables = 0 net.bridge.bridge-nf-call-arptables = 0 # Controls the default maxmimum size of a mesage queue kernel.msgmnb = 65536 # Controls the maximum size of a message, in bytes kernel.msgmax = 65536 # Controls the maximum shared segment size, in bytes kernel.shmmax = 68719476736 # Controls the maximum number of shared memory segments, in pages kernel.shmall = 4294967296 Contents of /etc/radvd.conf # NOTE: there is no such thing as a working "by-default" configuration file. # At least the prefix needs to be specified. Please consult the radvd.conf(5) # man page and/or /usr/share/doc/radvd-*/radvd.conf.example for help. # # interface eth0 { AdvSendAdvert on; MinRtrAdvInterval 3; MaxRtrAdvInterval 10; AdvDefaultPreference low; AdvHomeAgentFlag off; prefix fd8a:8d9d:808f:1::/64 { AdvOnLink on; AdvAutonomous on; AdvRouterAddr on; }; }; Contents of /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 HWADDR=52:54:00:74:d7:46 TYPE=Ethernet UUID=af5db1cb-e809-4098-be1a-5a74dbb767b1 ONBOOT=yes NM_CONTROLLED=no BOOTPROTO=dhcp IPV6INIT=yes IPV6_AUTOCONF=yes I've also enabled radvd at startup through chkconfig. Though I noticed that radvd is starting after interfaces are brought up. I've tried restarting the network service afterwards but still I get the following link-local address only #ip -6 addr show 1: lo: mtu 16436 inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: mtu 1500 qlen 1000 inet6 fe80::5054:ff:fe74:d746/64 scope link valid_lft forever preferred_lft forever Edit: Based on the answer given by Sander Steffann I still need clarification on some points but I'm posting here what worked. Contents of /etc/sysconfig/network NETWORKING=yes HOSTNAME=syslog-ng-server NETWORKING_IPV6=yes IPV6FORWARDING=yes Contents of /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 HWADDR=52:54:00:74:d7:46 TYPE=Ethernet UUID=af5db1cb-e809-4098-be1a-5a74dbb767b1 ONBOOT=yes NM_CONTROLLED=no BOOTPROTO=dhcp IPV6INIT=yes IPV6_AUTOCONF=yes IPV6FORWARDING=no Removed following line from /etc/sysctl.conf net.ipv6.conf.all.forwarding = 1 Contents of /etc/radvd.conf is as previous.

    Read the article

  • How do I create multiple instances of Certificate Server on the same Windows installation?

    - by makerofthings7
    The following URLs describe a new feature of Windows Certificate server is the ability to install multiple instances on the same server. (see end of "transcript" link it's a zip file) http://www.digitalsupporttech.com/mskb/896/896733_TechNet_Support_WebCast:_Best_Practices_for_Public_Key_Infrastructure:_Steps_to_build_an_offline_root_certification_authority_%28part_1_of_2%29.htm Quote: "Multiple Certificate Server instances on a single physical server" http://winintro.ru/certsvr.en/html/cf5622e1-daa9-42cc-8b43-14953e34f8b6.htm Quote: "Multiple instances of the Certificate Enrollment Web Service can be installed on a single computer in order to support multiple CAs." Question How can I actually implement multiple CA instances on a Windows 2008R2 server?

    Read the article

  • google android sdk [closed]

    - by user34373
    Possible Duplicate: google android with nmap I am trying to install a port scanner on android sdk which is installed on ubuntu.I have two problems: how to install any linux application on android SDK?? how to copy the data from the local hard drive to the emulator??

    Read the article

  • 7-zip archive with hard links?

    - by Steven Penny
    I see that tar respects hard links $ ln clonezilla.iso test.iso $ tar cfvvJ archive.tar.xz *.iso -rw-r--r-- Steven 111149056 2012-03-25 07:34 clonezilla.iso hrw-r--r-- Steven 0 2012-03-25 07:34 test.iso link to clonezilla.iso 7-Zip does not do this $ 7z a -mx=9 archive.7z *.iso $ ls -l -rw-r--r-- 1 Steven 212827496 Apr 17 07:40 archive.7z -rw-r--r-- 1 Steven 105073772 Apr 17 07:38 archive.tar.xz Is there a way to make 7-Zip respect hard links? gnu.org/software/tar/manual/html_node/hard-links

    Read the article

  • internet disconnects

    - by Smokezzaj
    Internet disconnects and reconnects, computer is in a peer to peer workstation with two other computers XP o/s. Only one computer has this problem the other two don't disconnect. Computer's connect to switch no router is being used. Ipconfig shows a DHCP connection, local area connection status shows packets being sent out but packets are not being received or being received at a extremely slow rate. Tried Winstock tool, reinstalling network card driver, restored to previous date, checked ethernet cable and release/renew IP.

    Read the article

  • Tomcat service start issue

    - by Srinivasan
    Hi, I have installed tomcat as service successfully. when i start this from control Panel- administrative tools - services, it tows error like this, The Apache Tomcat 4.1 service on local computer started and then stopped. Some service stop automatically if they have no work to do, for example, the performance logs and alerts sevice. Wat is the error?

    Read the article

  • Modifying IP Whois results?

    - by Rob
    Okay, I recently bought a dedicated server from santrex.net If you go here: http://domaintoip.com/ip.php?domain=188.72.215.27 It displays the whois information for that IP, santrex.net I want to modify my whois information, so that it displays my information instead, and doesn't link to santrex or santrex's ISP at all. Is this possible? If so, how would I go about doing it?

    Read the article

  • How to make Notepad++ take over from the standard notepad.exe

    - by Nick
    I could do this easily with TextPad, then I got irritated with Textpad once I'd played with Notepad++. Now that I've removed Textpad: I want Notepad++ to take over the right-click Edit option in Explorer, and I want Notepad++ to come up when I type notepad in the command prompt. I know that Notepad++ has a shell extension that allows one to do right-click Edit in Notepad++. But my old right-click Edit link remains, and I keep finding myself clicking on it, only to be rewarded with an error.

    Read the article

  • 6to4 tunnel: cannot ping6 to ipv6.google.com?

    - by quanta
    Hi folks, Follow the Setup of 6to4 tunnel guide, I want to test ipv6 connectivity, but I cannot ping6 to ipv6.google.com. Details below: # traceroute 192.88.99.1 traceroute to 192.88.99.1 (192.88.99.1), 30 hops max, 40 byte packets 1 static.vdc.vn (123.30.53.1) 1.514 ms 2.622 ms 3.760 ms 2 static.vdc.vn (123.30.63.117) 0.608 ms 0.696 ms 0.735 ms 3 static.vdc.vn (123.30.63.101) 0.474 ms 0.477 ms 0.506 ms 4 203.162.231.214 (203.162.231.214) 11.327 ms 11.320 ms 11.312 ms 5 static.vdc.vn (222.255.165.34) 11.546 ms 11.684 ms 11.768 ms 6 203.162.217.26 (203.162.217.26) 42.460 ms 42.424 ms 42.401 ms 7 218.188.104.173 (218.188.104.173) 42.489 ms 42.462 ms 42.415 ms 8 218.189.5.10 (218.189.5.10) 42.613 ms 218.189.5.42 (218.189.5.42) 42.273 ms 42.300 ms 9 d1-26-224-143-118-on-nets.com (118.143.224.26) 205.752 ms d1-18-224-143-118-on-nets.com (118.143.224.18) 207.130 ms d1-14-224-143-118-on-nets.com (118.143.224.14) 206.970 ms 10 218.189.5.150 (218.189.5.150) 207.456 ms 206.349 ms 206.941 ms 11 * * * 12 10gigabitethernet2-1.core1.lax1.he.net (72.52.92.121) 214.087 ms 214.426 ms 214.818 ms 13 192.88.99.1 (192.88.99.1) 207.215 ms 199.270 ms 209.391 ms # ifconfig tun6to4 tun6to4 Link encap:IPv6-in-IPv4 inet6 addr: 2002:x:x::/16 Scope:Global inet6 addr: ::x.x.x.x/128 Scope:Compat UP RUNNING NOARP MTU:1480 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:11 dropped:0 overruns:0 carrier:11 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) # iptunnel sit0: ipv6/ip remote any local any ttl 64 nopmtudisc tun6to4: ipv6/ip remote any local x.x.x.x ttl 64 # ip -6 route show ::/96 via :: dev tun6to4 metric 256 expires 21332777sec mtu 1480 advmss 1420 hoplimit 4294967295 2002::/16 dev tun6to4 metric 256 expires 21332794sec mtu 1480 advmss 1420 hoplimit 4294967295 fe80::/64 dev eth0 metric 256 expires 15674592sec mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth1 metric 256 expires 15674597sec mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev tun6to4 metric 256 expires 21332794sec mtu 1480 advmss 1420 hoplimit 4294967295 default via ::192.88.99.1 dev tun6to4 metric 1 expires 21332861sec mtu 1480 advmss 1420 hoplimit 4294967295 # ping6 -n -c 4 ipv6.google.com PING ipv6.google.com(2404:6800:8005::68) 56 data bytes From 2002:x:x:: icmp_seq=0 Destination unreachable: Address unreachable From 2002:x:x:: icmp_seq=1 Destination unreachable: Address unreachable From 2002:x:x:: icmp_seq=2 Destination unreachable: Address unreachable From 2002:x:x:: icmp_seq=3 Destination unreachable: Address unreachable --- ipv6.google.com ping statistics --- 4 packets transmitted, 0 received, +4 errors, 100% packet loss, time 2999ms What is my problem? Thanks,

    Read the article

  • How do I turn on Greasemonkey live editing?

    - by Delirium tremens
    On Firefox, I click Tools, Addons, Extensions, Greasemonkey, Options, select my user script, click Edit, change the source code, reload one of the included pages, but the script is the unchanged version. On User Scripts, logged in, I click my username, Script Management, my script's name, Admin, Edit Code Online, change the source code, click save, the link to the install page, install and the script is the changed version. How do you turn on Live Editing? While following Greasemonkey tutorials, this feature is not working...

    Read the article

  • rsync doesn’t sync files

    - by modi
    Hi I'm using rsync(with Cygwin) to sync 2 local folder The folder contains binary files I'm using the following command rsync.exe -av dir1/ dir2/ but the files in dir2 where only partially update, there are few different files does anybody know of a problem with rsync on windows? should i use some other flags 10'xs

    Read the article

  • Useful extensions for MediaWiki

    - by Stan
    Can anyone suggestion some useful MediaWiki extension? I've installed PDF export, syntax lighlight, file link protocol, submit in toolbar, enforce strong password. But still eager to know any good/handy extensions. Thanks

    Read the article

  • Access Home Network Server via External Address

    - by Dominic Barnes
    For the last few months, I've been using a server on my home network for basic backups and hosting some small websites. Up until this past week, I've been using Comcast (cable) as an ISP and now that I've moved into an apartment, I'm using AT&T. (DSL) I've set up dynamic DNS and I can verify it works externally. However, I can't seem to access the public address from within the local network. Is there something DSL does differently from Cable that makes this frustration possible?

    Read the article

  • DKIM error: dkim=neutral (bad version) header.i=

    - by GBC
    Ive been struggling the last couple of hours with setting up DKIM on my Postfix/CentOS 5.3 server. It finally sends and signs the emails, but apparently Google still does not like it. The errors I'm getting are: dkim=neutral (bad version) [email protected] from googles "show original" interface. This is what my DKIM-signature header look like: v=1; a=rsa-sha1; c=simple/simple; d=mydomain.com.au; s=default; t=1267326852; bh=0wHpkjkf7ZEiP2VZXAse+46PC1c=; h=Date:From:Message-Id:To:Subject; b=IFBaqfXmFjEojWXI/WQk4OzqglNjBWYk3jlFC8sHLLRAcADj6ScX3bzd+No7zos6i KppG9ifwYmvrudgEF+n1VviBnel7vcVT6dg5cxOTu7y31kUApR59dRU5nPR/to0E9l dXMaBoYPG8edyiM+soXo7rYNtlzk+0wd5glgFP1I= Very appreciative of any suggestions as to how I can solve this problem! Btw, here is exactly how I installed dkim-milter in CentOS 5.3 for postfix, if anyone is interested (based on this guide): mkdir dkim-milter cd dkim-milter wget http://www.topdog-software.com/oss/dkim-milter/dkim-milter-2.8.3-1.x86_64.rpm ======S====== Newest version: http://www.topdog-software.com/oss/dkim-milter/ ======E====== rpm -Uvh dkim-milter-2.8.3-1.x86_64.rpm /usr/bin/dkim-genkey -r -d mydomain.com.au ======S====== add contents of default.txt to DNS as TXT _ssp._domainkey TXT dkim=unknown _adsp._domainkey TXT dkim=unknown default._domainkey TXT v=DKIM1; g=*; k=rsa; p=MIGfMA0GCSqGSIb3DQEBAQUAA4GWETBNiQKBgQC5KT1eN2lqCRQGDX+20I4liM2mktrtjWkV6mW9WX7q46cZAYgNrus53vgfl2z1Y/95mBv6Bx9WOS56OAVBQw62+ksXPT5cRUAUN9GkENPdOoPdpvrU1KdAMW5c3zmGOvEOa4jAlB4/wYTV5RkLq/1XLxXfTKNy58v+CKETLQS/eQIDAQAB ======E====== mv default.private default mkdir /etc/mail/dkim/keys/mydomain.com.au mv default /etc/mail/dkim/keys/mydomain.com.au chmod 600 /etc/mail/dkim/keys/mydomain.com.au/default chown dkim-milt.dkim-milt /etc/mail/dkim/keys/mydomain.com.au/default vim /etc/dkim-filter.conf ======S====== ADSPDiscard yes ADSPNoSuchDomain yes AllowSHA1Only no AlwaysAddARHeader no AutoRestart yes AutoRestartRate 10/1h BaseDirectory /var/run/dkim-milter Canonicalization simple/simple Domain mydomain.com.au #add all your domains here and seperate them with comma ExternalIgnoreList /etc/mail/dkim/trusted-hosts InternalHosts /etc/mail/dkim/trusted-hosts KeyList /etc/mail/dkim/keylist LocalADSP /etc/mail/dkim/local-adsp-rules Mode sv MTA MSA On-Default reject On-BadSignature reject On-DNSError tempfail On-InternalError accept On-NoSignature accept On-Security discard PidFile /var/run/dkim-milter/dkim-milter.pid QueryCache yes RemoveOldSignatures yes Selector default SignatureAlgorithm rsa-sha1 Socket inet:20209@localhost Syslog yes SyslogSuccess yes TemporaryDirectory /var/tmp UMask 022 UserID dkim-milt:dkim-milt X-Header yes ======E====== vim /etc/mail/dkim/keylist ======S====== *@mydomain.com.au:mydomain.com.au:/etc/mail/dkim/keys/mydomain.com.au/default ======E====== vim /etc/postfix/main.cf ======S====== Add: smtpd_milters = inet:localhost:20209 non_smtpd_milters = inet:localhost:20209 milter_protocol = 2 milter_default_action = accept ======E====== vim /etc/mail/dkim/trusted-hosts ======S====== localhost 127.0.0.1 ======E====== /etc/mail/local-host-names ======S====== localhost 127.0.0.1 ======E====== /sbin/chkconfig dkim-milter on /etc/init.d/dkim-milter start /etc/init.d/postfix restart

    Read the article

  • Assign fixed IP address via DHCP by DNS lookup

    - by Janoszen
    Preface I'm building a virtualization environment with Ubuntu 14.04 and LXC. I don't want to write my own template since the upgrade from 12.04 to 14.04 has shown that backwards compatibility is not guaranteed. Therefore I'm deploying my virtual machines via lxc-create, using the default Ubuntu template. The DNS for the servers is provided by Amazon Route 53, so no local DNS server is needed. I also use Puppet to configure my servers, so I want to keep the manual effort on the deployment minimal. Now, the default Ubuntu template assigns IP addresses via DHCP. Therefore, I need a local DHCP server to assign IP addresses to the nodes, so I can SSH into them and get Puppet running. Since Puppet requires a proper DNS setup, assigning temporary IP addresses is not an option, the client needs to get the right hostname and IP address from the start. Question What DHCP server do I use and how do I get it to assign the IP address based only on the host-name DHCP option by performing a DNS lookup on that very host name? What I've tried I tried to make it work using the ISC DHCP server, however, the manual clearly states: Please be aware that only the dhcp-client-identifier option and the hardware address can be used to match a host declaration, or the host-identifier option parameter for DHCPv6 servers. For example, it is not possible to match a host declaration to a host-name option. This is because the host-name option cannot be guaranteed to be unique for any given client, whereas both the hardware address and dhcp-client-identifier option are at least theoretically guaranteed to be unique to a given client. I also tried to create a class that matches the hostname like this: class "my-client-name" { match if option host-name = "my-client-name"; fixed-address my-client-name.my-domain.com; } Unfortunately the fixed-address option is not allowed in class statements. I can replace it with a 1-size pool, which works as expected: subnet 10.103.0.0 netmask 255.255.0.0 { option routers 10.103.1.1; class "my-client-name" { match if option host-name = "my-client-name"; } pool { allow members of "my-client-name"; range 10.103.1.2 10.103.1.2; } } However, this would require me to administer the IP addresses in two places (Amazon Route53 and the DHCP server), which I would prefer not to do. About security Since this is only used in the bootstrapping phase on an internal network and is then replaced by a static network configuration by Puppet, this shouldn't be an issue from a security standpoint. I am, however, aware that the virtual machine bootstraps with "ubuntu:ubuntu" credentials, which I intend to fix once this is running.

    Read the article

  • Pass the output of ls to diff

    - by joachim
    I have one file that contains a list of files from a server, and a local folder that I compare to that manifest. Obviously, I do 'ls -1 listing_local' and then diff that file with listing_server. But is it possible to diff the manifest and the output of ls immediately to the diff command?

    Read the article

  • Cliq Wireless questions

    - by Nathan Adams
    Heres the deal: I am by no means a Linux expert, even less when it comes to the Android OS but lets see if we can't solve this problem. The problem I am having is that on the Cliq we have a broadcom chip. In order to use the wireless card you must first insert the module into the kernel. Fine: # insmod /system/lib/dhd.ko insmod /system/lib/dhd.ko # lsmod lsmod dhd 164936 0 - Live 0xbf000000 # BUT netcfg (or ifconfig in busybox) does not recognize that there is a wireless adapter there: # netcfg netcfg lo UP 127.0.0.1 255.0.0.0 0x00000049 dummy0 DOWN 0.0.0.0 0.0.0.0 0x00000082 rmnet0 UP 14.67.164.2 255.255.255.252 0x00001043 rmnet1 DOWN 0.0.0.0 0.0.0.0 0x00001002 rmnet2 DOWN 0.0.0.0 0.0.0.0 0x00001002 usb0 DOWN 0.0.0.0 0.0.0.0 0x00001002 # busybox ifconfig busybox ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:282 errors:0 dropped:0 overruns:0 frame:0 TX packets:282 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:18754 (18.3 KiB) TX bytes:18754 (18.3 KiB) rmnet0 Link encap:Ethernet HWaddr EE:83:E8:B4:4A:ED inet addr:14.x.x.x Bcast:14.67.164.3 Mask:255.255.255.252 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:7148 errors:0 dropped:0 overruns:0 frame:0 TX packets:7659 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2609236 (2.4 MiB) TX bytes:908575 (887.2 KiB) # For giggles if we attempt to launch wpa_supplicant anyways we get this: # wpa_supplicant -Dwext -ieth0 -c/data/misc/wifi/wpa_supplicant.conf wpa_supplicant -Dwext -ieth0 -c/data/misc/wifi/wpa_supplicant.conf ioctl[SIOCSIWPMKSA]: No such device ioctl[SIOCSIWMODE]: No such device Could not configure driver to use managed mode ioctl[SIOCGIFFLAGS]: No such device Could not set interface 'eth0' UP ioctl[SIOCGIWRANGE]: No such device ioctl[SIOCGIFINDEX]: No such device CTRL-EVENT-STATE-CHANGE id=-1 state=0 ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWAUTH]: No such device WEXT auth param 7 value 0x0 - Failed to disable WPA in the driver. ioctl[SIOCSIWAUTH]: No such device WEXT auth param 5 value 0x0 - ioctl[SIOCSIWAUTH]: No such device WEXT auth param 4 value 0x0 - ioctl[SIOCSIWAP]: No such device ioctl[SIOCGIFFLAGS]: No such device # In dmesg we get: <4>[18300.494065] dhd_oob_enable_intr : enable <4>[18305.019976] dhd_net_start failed bus is not ready <4>[18305.020278] dhdsdio_probe: dhd_net_start failed! Do I need to specify the firmware with insmod? Why are we trying to control the interface manually instead of through the Android API? The Android API doesn't support ad-hoc connections as far as I can tell. The card, I am sure, most certainly can.

    Read the article

  • Any way to view dynamic java content ex-post? Browser session still open

    - by Ryan
    I feel like a grandpa from 1996 asking this, but is it at all possible to view a representation of a particular screen that was rendered as part of a java-based online checkout process I executed a couple days ago? I haven't cleared my browser cache or temp files or anything, and I don't think I've restarted the comp or even the browser since. I'm using mac OS X 10.6.8, and the page(s) were viewed with Chrome version 21.0.1180.89 in standard mode (not incognito). Specifically the page in question was part of Verizon Wireless's 'iconic' contract/checkout process, which leads the user through several pages to make selections on various criteria and seems to be based on java. (Obviously I'm a dummy regarding web stuff so the question is probably not very well defined, I'm happy to elaborate). ^This is the tl;dr question. If it belongs on another site please just let me know. This is what I've been able to figure out on my own, for the bored / ultra-helpful / those who could use a laugh at a noob fumbling his way around cache files with no idea what he's doing: The progress through the selection pages is very clear in Chrome's browser history, the sequential pages are: https://www.verizonwireless.com/b2c/accountholder/estore/phoneupgrade?execution=e3s2 https://www.verizonwireless.com/b2c/accountholder/estore/phoneupgrade?execution=e3s3 https://www.verizonwireless.com/b2c/accountholder/estore/phoneupgrade?execution=e3s4 https://www.verizonwireless.com/b2c/accountholder/estore/phoneupgrade?execution=e3s5 https://preorder.verizonwireless.com/iconic/?format=JSON&value={%22action%22:%22START_ORDER%22,%22custType%22:%22EXISTING%22,%22orderType%22:%22UPGRADE%22,%22lookupMtn%22:%22*(NumberA)*%22,%22lineData%22:[{%22mtn%22:%22*(NumberA)*%22,%22upgType%22:%22ALTERNATE_UPGRADE%22,%22eligibleMtn%22:%22*(NumberB)*%22}]} https://preorder.verizonwireless.com/iconic/iconic/secured/screens/IconicOrder.do?format=JSON&value={%22action%22:%22START_ORDER%22,%22custType%22:%22EXISTING%22,%22orderType%22:%22UPGRADE%22,%22lookupMtn%22:%22*(NumberA)*%22,%22lineData%22:[{%22mtn%22:%22*(NumberA)*%22,%22upgType%22:%22ALTERNATE_UPGRADE%22,%22eligibleMtn%22:%22*(NumberB)*%22}]} https://preorder.verizonwireless.com/iconic/iconic/secured/screens/IconicEligibility.do https://preorder.verizonwireless.com/iconic/iconic/secured/screens/IconicDeviceSelection.do https://preorder.verizonwireless.com/iconic/iconic/secured/screens/PlanOptions.do https://preorder.verizonwireless.com/iconic/iconic/secured/screens/IconicFeatures.do https://preorder.verizonwireless.com/iconic/iconic/secured/screens/IconicAccessories.do https://preorder.verizonwireless.com/iconic/iconic/secured/screens/IconicShipmentBilling.do https://preorder.verizonwireless.com/iconic/iconic/secured/screens/IconicReview.do https://preorder.verizonwireless.com/iconic/iconic/secured/screens/IconicPaymentCreditInfo.do https://preorder.verizonwireless.com/iconic/iconic/secured/screens/IconicConfirmation.do The visual representation I would need could come from any of these pages, as the necessary information was shown at the top of each of them (although the two with long URLs were just like redirects or something). Of course, clicking the link to the page in History right now requires a new sign-in and just returns the user to the initial step for doing the process again; it does not pull up a representation of the page as it was seen several days ago. This I understand. Instead using Chrome's integrated cache viewer by typing about:cache in the address bar, I can search and find links that appear to be relevant, when I click on the link I just get a http header and a bunch of hexadecimal gobbledygook. I've tried to use the URL at the top of the cache and URLs in the http headers, but they take me to current versions of those pages and not the versions I saw during the checkout process. I tried this with a few of them but stopped because I noticed that it updated the date in the http header to the present moment and I don't want to take chances overwriting the cache files since I don't know what I'm doing. The links to the cache files look like this: https://login.verizonwireless.com/amserver/UI/Login?realm=vzw&goto=https%3A%2F%2Fpreorder.verizonwireless.com%3A443%2Ficonic%2Ficonic%2Fsecured%2Fscreens%2FPlanOptions.do https://preorder.verizonwireless.com/iconic/iconic/screens/customerTypeOverlay.jsp https://verizonwireless.tt.omtrdc.net/m2/verizonwireless/mbox/standard?mboxHost=login.verizonwireless.com&mboxSession=1347776884663-145230&mboxPC=1347609748832-956765.19&mboxPage=1347776884663-145230&screenHeight=1200&screenWidth=1920&browserWidth=1299&browserHeight=868&browserTimeOffset=-420&colorDepth=24&mboxCount=1&mbox=My_Verizon_Global&mboxId=0&mboxTime=1347751684666&mboxURL=https%3A%2F%2Flogin.verizonwireless.com%2Famserver%2FUI%2FLogin%3Frealm%3Dvzw%26goto%3Dhttps%253A%252F%252Fpreorder.verizonwireless.com%253A443%252Ficonic%252Ficonic%252Fsecured%252Fscreens%252FPlanOptions.do&mboxReferrer=&mboxVersion=41 and https://verizonwireless.tt.omtrdc.net/m2/verizonwireless/mbox/standard?mboxHost=login.verizonwireless.com&mboxSession=1347735676953-663794&mboxPC=1347609748832-956765.19&mboxPage=1347738347511-550383&screenHeight=1200&screenWidth=1920&browserWidth=1299&browserHeight=845&browserTimeOffset=-420&colorDepth=24&mboxCount=1&mbox=My_Verizon_Global&mboxId=0&mboxTime=1347713147517&mboxURL=https%3A%2F%2Flogin.verizonwireless.com%2Famserver%2FUI%2FLogin%3Frealm%3Dvzw%26goto%3Dhttps%253A%252F%252Fpreorder.verizonwireless.com%253A443%252Ficonic%252Ficonic%252Fsecured%252Fscreens%252FIconicOrder.do%253Fformat%253DJSON%2526value%253D%257B%252522action%252522%253A%252522START_ORDER%252522%252C%252522custType%252522%253A%252522EXISTING%252522%252C%252522orderType%252522%253A%252522UPGRADE%252522%252C%252522lookupMtn%252522%253A%252522*(NumberA)*%252522%252C%252522lineData%252522%253A%255B%257B%252522mtn%252522%253A%252522*(NumberA)*%252522%252C%252522upgType%252522%253A%252522ALTERNATE_UPGRADE%252522%252C%252522eligibleMtn%252522%253A%252522*(NumberB)*%252522%257D%255D%257D&mboxReferrer=&mboxVersion=41 and the http headers look like this: HTTP/1.1 200 OK Server: VZW Date: Sun, 16 Sep 2012 14:55:48 GMT Cache-control: private Pragma: no-cache Expires: 0 X-dsameversion: VZW Am_client_type: genericHTML Content-type: text/html;charset=ISO-8859-1 Content-Encoding: gzip Content-Length: 6220 and HTTP/1.1 200 OK Cache-Control: no-cache Date: Sun, 16 Sep 2012 16:16:30 GMT Content-Type: text/html Expires: Thu, 01 Jan 1970 00:00:00 GMT Content-Encoding: gzip X-Powered-By: Servlet/2.5 JSP/2.1 and HTTP/1.1 302 Moved Temporarily Server: VZW Date: Sun, 16 Sep 2012 16:29:32 GMT Cache-control: private Pragma: no-cache X-dsameversion: VZW Am_client_type: genericHTML Location: https://preorder.verizonwireless.com:443/iconic/iconic/secured/screens/IconicOrder.do?format=JSON&value={%22action%22:%22START_ORDER%22,%22custType%22:%22EXISTING%22,%22orderType%22:%22UPGRADE%22,%22lookupMtn%22:%22*(*(NumberA)*%22,%22lineData%22:[{%22mtn%22:%22*(NumberA)*%22,%22upgType%22:%22ALTERNATE_UPGRADE%22,%22eligibleMtn%22:%22*(NumberB)*%22}]} Content-length: 0 ^^this last one actually returned me to a page in the middle of the process when I used the "Location:" given in this http header rather than the URL at the top of the cache page (and was signed in to Verizon's website through a separate tab), but the page it took me to had already been updated to reflect new information, it wasn't presented as of the time the actions were taken several days ago when the page was originally viewed. (It's clear I can't achieve what I'm looking for by visiting current versions of these pages on the web…I should actually probably disable my network adapter while testing this out). The cache folder seems promising, but I don't know what to make of all that hexadecimal mess - if it contains what I'm looking for and if so, how to view it. Finally, the third thing I've come across is the Google Chrome cache folder on my local machine, at ~/Library/Caches/Google/Chrome/ then there are 'Default' and 'Media Cache' folders within. There are ~4,000 files in the former averaging ~100kb each, and 100 files in the latter averaging ~900kb each. The filenames all start "f_00xxxx" except for files titled data_0 through data_4 in each folder. I'm not sure how to observe the contents of these files and don't really want to start opening them up and potentially overwriting existing cached pages, as I notice there are already some holes in the arrangement of the files which I have never deleted manually. Hopefully this is an easy question to answer for someone who knows this stuff, admittedly web stuff is my weak point. As such, I've spent the past five hours searching around and trying to provide all the information I can. I'm probably asking for a miracle - like can those cached pages full of hexadecimal data be used to recreate the representation of the information that was on screen during the process? Or could screenshots of the previously viewed webpages be lurking in the /Caches folder? I have doubt because the content wasn't viewed at a permanent link, rather it seems like the on-screen information was served by Verizon's db, and probably securely so. I'm just not sure if Chrome saves the visual rendering of the page contents somewhere, even just temporarily. Alternatively I would be happy just to get the raw data that was on the page, even if not a visual representation…I just need to be able to demonstrate the phone line that was referenced on this page: https://preorder.verizonwireless.com/iconic/iconic/secured/screens/IconicFeatures.do . Can anyone point me in the right direction?

    Read the article

  • re-use '~/.profile` for Fish?

    - by Albert
    (I'm talking about the shell Fish, esp. Fish's Fish.) For Bash/ZSH, I had ~/.profile with some exports, aliases and other stuff. I don't want to have a separate config for environment variables for Fish, I want to re-use my ~/.profile. How? In The FAQ, it is stated that I can at least import those via /usr/local/share/fish/tools/import_bash_settings.py, however I don't really like running that for each Fish-instance.

    Read the article

  • Adaptec 5805 after reboot don't starting

    - by Rakedko ShotGuns
    After rebooting the system, the controller is not included. It only works if the computer is shut down and turn off. Late i update firmware "Adaptec RAID 5805 Firmware Build 18948" How to fix the problem? add Log Configuration summary Server name.....................raid_test Adaptec Storage Manager agent...7.31.00 (18856) Adaptec Storage Manager console.7.31.00 (18856) Number of controllers...........1 Operating system................Windows Configuration information for controller 1 ------------------------------------------------------- Type............................Controller Model...........................Adaptec 5805 Controller number...............1 Physical slot...................2 Installed memory size...........512 MB Serial number...................8C4510C6C9E Boot ROM........................5.2-0 (18948) Firmware........................5.2-0 (18948) Device driver...................5.2-0 (16119) Controller status...............Optimal Battery status..................Charging Battery temperature.............Normal Battery charge amount (%).......37 Estimated charge remaining......0 days, 16 hours, 12 minutes Background consistency check....Disabled Copy back.......................Disabled Controller temperature..........Normal (40C / 104F) Default logical drive task priorityHigh Performance mode................Dynamic Number of logical devices.......1 Number of hot-spare drives......0 Number of ready drives..........0 Number of drive(s) assigned to MaxCache cache0 Maximum drives allowed for MaxCache cache8 MaxCache Read Cache Pool Size...0 GB NCQ status......................Enabled Stay awake status...............Disabled Internal drive spinup limit.....0 External drive spinup limit.....0 Phy 0...........................No device attached Phy 1...........................No device attached Phy 2...........................No device attached Phy 3...........................1.50 Gb/s Phy 4...........................No device attached Phy 5...........................No device attached Phy 6...........................No device attached Phy 7...........................No device attached Statistics version..............2.0 SSD Cache size..................0 Pages on fetch list.............0 Fetch list candidates...........0 Candidate replacements..........0 69319...........................31293 Logical device..................0 Logical device name............. RAID level......................Simple volume Data space......................148,916 GB Date created....................09/19/2012 Interface type..................Serial ATA State...........................Optimal Read-cache mode.................Enabled Preferred MaxCache read cache settingEnabled Actual MaxCache read cache setting Disabled Write-cache mode................Enabled (write-back) Write-cache setting.............Enabled (write-back) Partitioned.....................Yes Protected by hot spare..........No Bootable........................Yes Bad stripes.....................No Power Status....................Disabled Power State.....................Active Reduce RPM timer................Never Power off timer.................Never Verify timer....................Never Segment 0.......................Present: controller 1, connector 0, device 0, S/N 9RX3KZMT Overall host IOs................99075 Overall MB......................4411203 DRAM cache hits.................71929 SSD cache hits..................0 Uncached IOs....................29239 Overall disk failures...........0 DRAM cache full hits............71929 DRAM cache fetch / flush wait...0 DRAM cache hybrid reads.........3476 DRAM cache flushes..............-- Read hits.......................0 Write hits......................0 Valid Pages.....................0 Updates on writes...............0 Invalidations by large writes...0 Invalidations by R/W balance....0 Invalidations by replacement....0 Invalidations by other..........0 Page Fetches....................0 0...............................0 73..............................10822 8...............................3 46138...........................4916 27184...........................15226 20875...........................323 16982...........................1771 1563............................5317 1948............................2969 Serial attached SCSI ----------------------- Type............................Disk drive Vendor..........................Unknown Model...........................ST3160815AS Serial Number...................9RX3KZMT Firmware level..................3.AAD Reported channel................0 Reported SCSI device ID.........0 Interface type..................Serial ATA Size............................149,05 GB Negotiated transfer speed.......1.50 Gb/s State...........................Optimal S.M.A.R.T. error................No Write-cache mode................Write back Hardware errors.................0 Medium errors...................0 Parity errors...................0 Link failures...................0 Aborted commands................0 S.M.A.R.T. warnings.............0 Solid-state disk (non-spinning).false MaxCache cache capable..........false MaxCache cache assigned.........false NCQ status......................Enabled Phy 0...........................1.50 Gb/s Power State.....................Full rpm Supported power states..........Full rpm, Powered off 0x01............................113 0x03............................98 0x04............................99 0x05............................100 0x07............................83 0x09............................75 0x0A............................100 0x0C............................99 0xBB............................100 0xBD............................100 0xBE............................61 0xC2............................39 0xC3............................69 0xC5............................100 0xC6............................100 0xC7............................200 0xC8............................100 0xCA............................100 Aborted commands................0 Link failures...................0 Medium errors...................0 Parity errors...................0 Hardware errors.................0 SMART errors....................0 End of the configuration information for controller 1 List item

    Read the article

  • finding IP address using Linux command prompt

    - by John Kube
    I'm looking for a way to get my IP address using the command prompt in Linux. I know when you type "ifconfig" you can get your local IP address (i.e. 192.168.0.103), but I'm looking for my IP address that I get from my ISP. How can I get this from Linux without having to visit some website?

    Read the article

< Previous Page | 523 524 525 526 527 528 529 530 531 532 533 534  | Next Page >