Search Results

Search found 2415 results on 97 pages for 'asus motherboard'.

Page 53/97 | < Previous Page | 49 50 51 52 53 54 55 56 57 58 59 60  | Next Page >

• Why is Ubuntu unmounting my primary hard drive?

  - by Twisol

  I'm running Ubuntu 10.10 on my laptop (an Asus G73j), dual-booting Windows 7 if that matters. After using the computer for couple of hours or so, I get a popup complaining that a file was unmounted, then my GNOME desktop panels disappear. I can't save any unsaved work (the file browser shows "Filesystem" as totally empty), and other programs break in odd ways (like Chrome can't browse to any new pages, but keeps current ones going... at least I still have Pandora to listen to when this happens!). I've tried looking in the system logs to no avail; I'm assuming that it can't write any errors to the logs because, of course, the logs are on the primary hard drives. This started happening maybe a few days ago. Yesterday I upgraded from 10.4, but I believe it was happening before then. Any advice for figuring this out?

  Read the article

• Uncontrolled Fan and Crash

  - by RobotbeatsHuman

  I don't have sensors to properly run lm-sensors. The computer will turn on but shortly there after all the fans in it will speed way up. It stays like this for a few minutes and then the computer shuts off. Tried resetting the BIO. Went to try installing a BIOs update but it wont stay on long enough for me to try that or to do a clean install. Could this be the motherboard dying? It's mainly the CPU fan that ends up going max. after a few minutes. I checked the PSU and It's a Dell Inspiron 580. If you need more system specs just le me know.

  Read the article

• MPD to play music to single channel of my multi-channel card?

  - by hany tawfik

  I installed an Ubuntu 12-04 LTS server for a special background music application of mine, where I am using the server with an Asus Xonar DS sound card. The installation is successful, the MPD is working, the sound card is working with Alsa and its libraries installed accept for Alsa-oss. Alsamixer is working fine with left/right sides of each channel volume control through Q/Z letters shortcut when alsamixer is open in terminal . using the command " speaker-test -Dplug:surround71 -c8 -l1 -twav " I can hear every voice message coming out from the card at the right connector, so "front right/ front left" voice message are coming from first output in the card back, while the other outputs are silent..so on. The problem is that MPD is playing on all outputs simultaneously the same audio. I have been trying various configurations for the last 12 days with out any success, including trying to put mappings in the /etc/asound.conf Can any body help me achieve the above, or direct me to the right configuration of MPD or asound.conf

  Read the article

• 'Invalid or corrupt kernel image' error while booting from USB stick

  - by steve

  I got the Ubuntu 11.10 32-bit edition and i used Unetbootin to write the ISO to a usb stick.After that i tried to boot from the stick,having changed the BIOS boot settings,and when the first interface shows up with the choices of istallation,whatever choice i select i got the message"invalid or corrupt kernel image".I use a netbook with windows 7 on it.I tried different usb sticks but same again.I also tried Universal USB installer instead of Unetbootin but same again.Any idea of what happens?I am using ASUS 1000H.The USB doesn't work in one more PC i tried to,but i also tried a second USB to both of the two computers and same again. I downloaded the ISO image once again and follow the same procedure but same again

  Read the article

• How to prevent Gnome desktop from crashing?

  - by nixnotwin

  I have ubuntu 10.10 32bit running on my Asus EEEPC 1005PX. I am experiencing frequent desktop crashes. When I turn on my netbook at least once in 5 times the defualt ubuntu theme disapears and the classic gnome theme appears. Many times while doing some work, the desktop crashes and the CLI gets shown, and after a few seconds the login screen appers. I am not using any widgets or dock bars, I just have a single gnome panel with default menus. The crashes also happen when using the default bundled ubuntu apps. Is there any way to avoid these crashes?

  Read the article

• Keep getting messages about internal system errors

  - by Tomas Lycken

  I keep getting popups about internal system errors (see screenshot below) on irregular intervals (several times a day), that I don't know what to do about. If I continue through the dialog and try to report the error back to the Ubuntu project, I get a message stating that development on this version of Ubuntu has been completed, and that I should ask for help here if I don't know what to do about it. I don't. If I show the details of the error message, the "executable path" parameter shows /usr/share/apport/apport-gpu-error-intel.py. Is this a bug I should report to Launchpad, or just a configuration error somewhere? If it's a bug, how do I collect the data I (and the devs) need? Update in response to comment: I am running an ASUS N53SN, sporting an Intel Core i7 2630QM CPU and an NVidia GeForce 550M GPU.

  Read the article

• Laptop won't boot or enter BIOS after deleting partition in Windows 7

  - by user111649

  I dual boot my computer and later decided to delete one of the Ubuntu partitions while using Windows 7. After my computer hibernated and I tried restarting my ASUS laptop it stopped at the logo and preventing me from entering the BIOS. When I take out my hard dive it allows me to enter the BIOS. It does not boot from a CD if the hard drive is still attached to the computer. After taking the hard drive out then it boots from the CD. Can someone please help?

  Read the article

• unable to enter bios

  - by fraz

  I have an asus desktop ( amd phenom X6 processor) which was preinstalled with windows 7. I wanted to install ubuntu on it (dual boot) but am unable to do so because of the boot order. So I thought of changing boot order thru bios. But it turns out, if I press any key while the computer is starting, it just doesnt boots. I can see that the keyboard and mouse are booted up. (the lights are on) but the monitor is in standby mode.. I tried tab, f2,f10, delete key. But nothing is working.. Is there a software or other alternate on how can I change boot order ? Thanks

  Read the article

• Loud and annoying noise on login

  - by searchfgold6789

  I have a PC with Kubuntu 13.10 64-bit on it. The problem is that whenever I log in (automatic log in is enabled), there is a loud double-click noise that sounds from the speakers whether the volume is muted or not. I have two sound cards; the motherboard audio, which is disabled in the BIOS, and the Creative! Labs Sound Blaster X-Fi SB0460, which I have normal speakers plugged into. Does anyone know how to fix this? Relative lspci lines: 00:01.1 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] BeaverCreek HDMI Audio [Radeon HD 6500D and 6400G-6600G series] 02:05.0 Multimedia audio controller: Creative Labs SB X-Fi Using default Phonon backend. (I am not really sure what other information to provide, but will gladly edit in anything upon request.)

  Read the article

• How do I get my Broadcom BCM4313 working correctly?

  - by Ataraxio Panzetta

  I've installed ubuntu on a Asus 1015 netbook. Everything worked out of the box except for the Wireless adapter, which i had to install with the Additional Drivers application. It apparently installed fine and connects to our wireless network, but it only works at a "funny" speed range that goes from 367Bytes to a peak of 3Kb in its best moments. I know for sure the problem is neither the network nor the hardware. Network speeds are normal under windows on this laptop and in other computers with ubuntu aswell. lspci says the card is a BCM4313 model, but the Addittional Drivers Manager says these packecege contains Broadcom 802.11 Linux STA wireless driverfor use with Broadcom's BCM4311-, BCM4312-, BCM4321-, and BCM4322 based hardware seems like it installed the wrong driver... Is there anything I can do? I'm not concerned about compiling the driver or stuff like that, but I'm not sure on where to start... any help or guidance will be very, very appreciated.

  Read the article

• Cursor (touchpad) moves and clicks erratically

  - by James Wood

  Sometimes (usually after two-finger scrolling) the touchpad on my Asus X54C becomes unresponsive and the cursor begins to click and move small distances. Clicking seems to happen more often than moving. Unlike with other similar problems, I've never seen the cursor move to (0, 0). Suspending (closing the lid) and unsuspending doesn't help, and neither does moving to a tty and back or rebooting. I've also tried disabling the touchpad via Fn+F9. That tends to take a long time, but doesn't have any effect. I'm on 13.10 at the moment, but I remember it happening on 13.04 as well. Here's the pointer section of xinput: ? Virtual core pointer id=2 [master pointer (3)] ? ? Virtual core XTEST pointer id=4 [slave pointer (2)] ? ? ETPS/2 Elantech Touchpad id=12 [slave pointer (2)]

  Read the article

• What the different hardware temperatures listed in psensor, sensor viewer etc reffer to?

  - by cipricus

  I have installed psensor and see a list of temperatures, but listed as ”Temperature 1”, 2, 3 etc . I can only guess where the processor is: but who's who for sure? The same question stands for Sensors Viewer. I can also type sensors in Terminal but I get no more than that acpi -t gives Thermal 0: ok, 65.0 degrees C Thermal 1: ok, 37.9 degrees C Thermal 2: ok, 56.0 degrees C Thermal 3: active, 71.0 degrees C Considering psensor, I know for a fact that: - the temperature that varies most depending on the CPU use is Temp1 and it is one of the two highest - the other high temperature is Temp4 and it goes to the ceiling when using youtube/flash - Temp2 is very stable at a medium level of 50-60 degrees Celsius - Temp3 is by far the lowest and most imobile So, I guess Temp1 is the CPU temperature, and Temp4 is the GPU temperature. Temp2 and 3 must be the motherboard and the hdd. Does anybody know for sure?

  Read the article

• Will grub overwrite EasyBCD entry if I already have Windows 7 and Windows XP installed?

  - by Sachin

  Installing Ubuntu on EEE PC which already has Windows 7 and Windows XP in dual boot using Easy BCD I have an ASUS EEE PC 1015PEM with Windows 7 starter and Windows XP in dual boot configuration on separate partitions. Now I want to replace my Windows XP with Ubuntu 11. Earlier after installing XP on my system it failed to boot in Windows 7, which I restored easily using EasyBCD. If I install Ubuntu 11 will I be able to boot my Windows 7 also? Will grub overwrite the EasyBCD entry for XP?

  Read the article

• Installer can't find any partition

  - by petter

  I have a ubuntu 11.10 cd which I burned. And when I try to install Ubuntu I come all the way until it tells me to format partitions / choose partitions. And it can't see ANY partition at all. I have Windows 7 at the moment. I really don't know what the problem is, I've been googling it and searching the forums but no luck. I tried to install with WUBI and rebooted it. And when I was in "ubuntu", at the desktop in ubuntu a error came up telling me to choose a partition. I have no clue what the the problem is... My computer is a Packard Bell model ixtreme m5150 and I don't know what motherboard I have unfortunately. I didn't build it. Please help me.

  Read the article

• Black bars around screen? Catalyst Control Center problem?

  - by Josh B

  I just newly install Ubuntu 12.04, and im running an HDMI cable from my computer to my ASUS monitor. Now in Windows 7, i did not have these black bar issues running at 1080p. But now in Ubuntu, i have these black bars. I installed the ATI Catalyst Control Center, and I went to go in to fix the scaling but it is grayed out. As you can see, even with the override box checked i still can not set the scaling. The monitor was set to a lower resolution to hopefully fix it but that did not work either. Does anyone know how to fix this? Thanks.

  Read the article

• In 10.10, USB 3.0 PCI Express card recognized by lspci but not lsusb or dmesg. How to fix?

  - by Paul

  Asus N PC, runs 10.10 x86_64 The Asus N comes with 4 usb 2.0 ports, each labelled 2.0 on the case. Attempting to add two usb 3.0 ports to be provided by a generic usb 3.0 pci express card installed in the pci expres slot. The new card says usb 3.0 and has the blue ports. The card is installed into the laptop unpowered, then the laptop is powered on and boots normally. Nothing happens when a USB 3.0 flash drive is inserted into the usb 3.0 port. uname -a Linux drpaulbrewer-N90SV 2.6.35.8 #1 SMP Fri Jan 14 15:54:11 EST 2011 x86_64 GNU/Linux lspci -v 00:00.0 Host bridge: Silicon Integrated Systems [SiS] 671MX Subsystem: ASUSTeK Computer Inc. Device 1b27 Flags: bus master, medium devsel, latency 64 Kernel modules: sis-agp 00:01.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: fa000000-fdefffff Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff Capabilities: [d0] Express Root Port (Slot+), MSI 00 Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit- Capabilities: [f4] Power Management version 2 Capabilities: [70] Subsystem: Silicon Integrated Systems [SiS] PCI-to-PCI bridge Kernel driver in use: pcieport 00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS968 [MuTIOL Media IO] (rev 01) Flags: bus master, medium devsel, latency 0 00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev 01) (prog-if 80 [Master]) Subsystem: ASUSTeK Computer Inc. Device 1b27 Flags: bus master, medium devsel, latency 128 I/O ports at 01f0 [size=8] I/O ports at 03f4 [size=1] I/O ports at 0170 [size=8] I/O ports at 0374 [size=1] I/O ports at ffe0 [size=16] Capabilities: [58] Power Management version 2 Kernel driver in use: pata_sis 00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f) (prog-if 10 [OHCI]) Subsystem: ASUSTeK Computer Inc. Device 1b27 Flags: bus master, medium devsel, latency 64, IRQ 20 Memory at f9fff000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd 00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f) (prog-if 10 [OHCI]) Subsystem: ASUSTeK Computer Inc. Device 1b27 Flags: bus master, medium devsel, latency 64, IRQ 21 Memory at f9ffe000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd 00:03.3 USB Controller: Silicon Integrated Systems [SiS] USB 2.0 Controller (prog-if 20 [EHCI]) Subsystem: ASUSTeK Computer Inc. Device 1b27 Flags: bus master, medium devsel, latency 64, IRQ 22 Memory at f9ffd000 (32-bit, non-prefetchable) [size=4K] Capabilities: [50] Power Management version 2 Kernel driver in use: ehci_hcd 00:04.0 Ethernet controller: Silicon Integrated Systems [SiS] 191 Gigabit Ethernet Adapter (rev 02) Subsystem: ASUSTeK Computer Inc. Device 11f5 Flags: bus master, medium devsel, latency 0, IRQ 19 Memory at f9ffcc00 (32-bit, non-prefetchable) [size=128] I/O ports at cc00 [size=128] Capabilities: [40] Power Management version 2 Kernel driver in use: sis190 Kernel modules: sis190 00:05.0 IDE interface: Silicon Integrated Systems [SiS] SATA Controller / IDE mode (rev 03) (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: ASUSTeK Computer Inc. Device 1b27 Flags: bus master, medium devsel, latency 64, IRQ 17 I/O ports at c800 [size=8] I/O ports at c400 [size=4] I/O ports at c000 [size=8] I/O ports at bc00 [size=4] I/O ports at b800 [size=16] I/O ports at b400 [size=128] Capabilities: [58] Power Management version 2 Kernel driver in use: sata_sis Kernel modules: sata_sis 00:06.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 Memory behind bridge: fdf00000-fdffffff Capabilities: [b0] Subsystem: Silicon Integrated Systems [SiS] Device 0004 Capabilities: [c0] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [d0] Express Root Port (Slot+), MSI 00 Capabilities: [f4] Power Management version 2 Kernel driver in use: pcieport 00:07.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=03, subordinate=06, sec-latency=0 I/O behind bridge: 0000e000-0000efff Memory behind bridge: fe000000-febfffff Prefetchable memory behind bridge: 00000000f6000000-00000000f8ffffff Capabilities: [b0] Subsystem: Silicon Integrated Systems [SiS] Device 0004 Capabilities: [c0] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [d0] Express Root Port (Slot+), MSI 00 Capabilities: [f4] Power Management version 2 Kernel driver in use: pcieport 00:0f.0 Audio device: Silicon Integrated Systems [SiS] Azalia Audio Controller Subsystem: ASUSTeK Computer Inc. Device 17b3 Flags: bus master, medium devsel, latency 0, IRQ 18 Memory at f9ff4000 (32-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 01:00.0 VGA compatible controller: nVidia Corporation G96 [GeForce GT 130M] (rev a1) (prog-if 00 [VGA controller]) Subsystem: ASUSTeK Computer Inc. Device 2021 Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at fc000000 (32-bit, non-prefetchable) [size=16M] Memory at d0000000 (64-bit, prefetchable) [size=256M] Memory at fa000000 (64-bit, non-prefetchable) [size=32M] I/O ports at dc00 [size=128] [virtual] Expansion ROM at fde80000 [disabled] [size=512K] Capabilities: [60] Power Management version 3 Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [78] Express Endpoint, MSI 00 Capabilities: [b4] Vendor Specific Information: Len=14 <?> Kernel driver in use: nvidia Kernel modules: nvidia-current, nouveau, nvidiafb 02:00.0 Network controller: Atheros Communications Inc. AR928X Wireless Network Adapter (PCI-Express) (rev 01) Subsystem: Device 1a3b:1067 Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at fdff0000 (64-bit, non-prefetchable) [size=64K] Capabilities: [40] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [60] Express Legacy Endpoint, MSI 00 Capabilities: [90] MSI-X: Enable- Count=1 Masked- Kernel driver in use: ath9k Kernel modules: ath9k 03:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) (prog-if 30) Flags: bus master, fast devsel, latency 0, IRQ 10 Memory at febfe000 (64-bit, non-prefetchable) [size=8K] Capabilities: [50] Power Management version 3 Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [90] MSI-X: Enable- Count=8 Masked- Capabilities: [a0] Express Endpoint, MSI 00 lsusb Bus 003 Device 002: ID 0b05:1751 ASUSTek Computer, Inc. BT-253 Bluetooth Adapter Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 004: ID 0bda:0158 Realtek Semiconductor Corp. USB 2.0 multicard reader Bus 001 Device 002: ID 04f2:b071 Chicony Electronics Co., Ltd 2.0M UVC Webcam / CNF7129 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub dmesg trying to post dmesg exceeded the stackexchange posting limit of 30K... but nothing there is usb 3.0

  Read the article

• EFI - GPT dual-boot quantal AMD64 - impossible boot windows 7

  - by Matt

  I tried to install Ubuntu Quantal AM64 on a EFI - GPT notebook (asus X501U) in dualboot. Ubuntu works fine, but i can't boot windows anymore. HDD is partitioned in this way: sda1 0.2 Gb boot efi sda2 0.128 Gb sda3 60 Gb Windows sda4 210 Gb Data sda5 15 Gb Ubuntu sda6 4 Gb swap sda7 25 Gb recovery image Booting pc, grub2 runs, but if i try to select "windows 7 loader on sda3" i receive this message: "error: invalid EFI file path." If i select "windows recovery Environment on sda7" i receive: "error: impossible find command "drivemap" - error: invalid EFI file path." I installed dualboot ubuntu many times, but this is the first time on a EFI - GPT system.

  Read the article

• Ubuntu 12.04 boot freezes

  - by Lajos Soukup

  I installed win7 on one of my machines. It works without any problem. Now I can not install Ubuntu 12.04 (11.10, 11.04) because the installation process stops in a very early stage: I can see that ISOLinux was loaded, then I can see some very simple icons, then I can see text messages of the kernel. The last message I can see: [6.177983] sr 5:0:0:0: attached scsi general ss1 type 5 At that point the system stops. I tried different versions (11.04) , I disabled, and then disconnected the hdd, but the same problem occured independently from my actions. I can boot a gparted live cd, but that system can not see my hdd. On the other hand, I can boot the installation cd of the latest stable Debian distribution without any problem, but I would prefer to use Ubuntu, because I use that distribution on all of our machines.s Configuration: Asus P8H61-MLE motheboard, Gigabyte GTS 450, Intel i5, 4gb ram, wd 1T sata hdd Any idea? Best regards, Lajos

  Read the article

• How do I play HD video without it stuttering?

  - by hugocreal

  Hello All, I want play a Blu Ray Video from my hard drive with Boxee, but it chokes all the time. I've tried to play it with others video players but it is the same. I think that is a 10gb .mkv file with 10Gb. Stuttering video with VLC , mplayer, and the default video player on ubuntu. I read in many Forums just can´t put this to work. Any idea? thanks. Ubuntu 10.10, My PC specs: Single Core 2Ghz ATI HD 4350 (i have installed the drivers from "Hardware Drivers"), 2G Memory *EDIT: Problem solved, this weekend had buy a motherboard and a processor DualCore 2.5Ghz, no more stuttering. thanks alot for your help.

  Read the article

• Cannot read from 2nd SATA data drive connected via SATA docking station

  - by Robbo

  Installed 10.10 this week on dual boot system. Everything else works fine but cannot read from 2nd SATA drive with all my data. Same drive works normally when booted to Windows XP. Interesting part is that I can see the drive in Ubuntu Disk Manager, can read all its attributes, can test it, shows up in Disk Manager, Storage Device Manager and Mount Manager, and can mount it, even change attributes; it appears healthy but does not show up in "Computer" or anywhere else that it can be accessed. The drive is connected via an external e-SATA docking station which is connected to a SATA port on the motherboard.

  Read the article

• Wireless very slow. Changed mode from Infracstructure to Ad-hoc

  - by Dan

  This is my first time using Linux so go easy on me :) I downloaded and installed Mint 11 couple of days ago and I was having trouble connecting to internet with wifi. Actually it says it connects but does not load any webpages. I tried to get help from this model of laptop owners (Asus G73SW) who uses mostly Ubuntu but they said they never had any problem right from install. So I decided to try out Ubuntu 11.04. Same thing. BUT now I get internet after going into Network Connection edit and changing the Mode from Infracstructure to Ad-Hoc. I get load pages but very slow. And if I'm not mistaken, as I was writing this paragraph, I might have been disconnected. However the wifi bar is full. Please help me this newb because I really want to keep using Ubuntu but I might just have to go back to W7 if nothing can be done. Thank you!

  Read the article

• Radeon HD 6290 terrible performance on a certified laptop

  - by dac

  I bought Asus K53U laptop, which is Ubuntu certified with pre-installed 11.10. The graphic card is Radeon HD 6290 but 720p playback is terrible. Even page scrolling in Firefox is very laggy. Proprietary drivers are installed by default. How is this possible, why is the laptop Ubuntu certified if the performance is poor? Any solution to this? I just did apt-get autoremove, and after that, this message came out in terminal: Error inserting vesafb (/lib/modules/3.0.0-15-generic/kernel/drivers/video/vesafb.ko): No such device Could that be the problem?

  Read the article

• Wireless connects but can not connect to internet

  - by Dan

  I'm using Ubuntu 11.04 and I'm having trouble connecting to internet via wifi. Ethernet cable works though. So when I log on it auto logs on to my wifi connection at home but after about a minute or so it gives me a popup: network disabled something about .local domain and something about Avahi network (sorry if you need more on what the popup says I will reboot and look at it again). I am using Atheros wireless card. My laptop is Asus G73SW and on the forum at notebookreview.com G73SW Owner's Lounge people said they had no problem with connecting via wifi from install. Please help me because I would love to keep using this beautiful OS.

  Read the article

• Plugging two external screens to laptop via VGA and HDMI

  - by avilella

  I have an Asus U30JC laptop with a VGA and HDMI ports. I can connect my external screen (1920x1200) to either of those ports but I wonder if I would be able to use two screens at the same time, one plugged to the VGA and the other to the HDMI socket. Any ideas? Where should I find out? Doing xrandr, I get: Screen 0: minimum 320 x 200, current 1366 x 768, maximum 8192 x 8192 LVDS1 connected 1366x768+0+0 (normal left inverted right x axis y axis) 293mm x 164mm 1366x768 60.0*+ 1360x768 59.8 60.0 1024x768 60.0 800x600 60.3 56.2 640x480 59.9 VGA1 disconnected (normal left inverted right x axis y axis) HDMI1 disconnected (normal left inverted right x axis y axis) DP1 disconnected (normal left inverted right x axis y axis)

  Read the article

• My ubuntu with unity not loading after last reboot

  - by Abonec

  I have asus u36sd and after last reboot I can't start up my ubuntu 11.10. Usually I suspend my notebook by closing cover but today I reboot it and it not starting up. Booting flowing by normal till to login screen but if I move mouse cursor after that image immediately switch to console (without any error; only normal loading startup processes) and back to login screen. I can type my password and boot continuing loading but after few moment it again switch back to dark console and switch again to login screen. I can load recovery mode but if I try touch my cursor (by mouse or internal notebook touchpad) it again switch back to console and to login screen. But if I use only keyboard it work fine. Where I can see detailed log information about my problem?

  Read the article

< Previous Page | 49 50 51 52 53 54 55 56 57 58 59 60  | Next Page >