Search Results

Search found 1682 results on 68 pages for 'colors'.

Page 53/68 | < Previous Page | 49 50 51 52 53 54 55 56 57 58 59 60  | Next Page >

  • Replacing stock Core 2 Duo heatsink fan (just the fan really) with a Dell CPU fan

    - by user647345
    My old heatsink fan broke and I'm trying to reconnect its plugs to a new fan. My Dell CPU fan has some custom Dell plug. I snipped the old fan's wire in half and kept the plug on the end of it. I want to connect it to the Dell fan wire to the plug. The motherboard is a P5Q-e, the stock Core 2 Duo fan was .20A and the dell is .70A. Is that going to matter? The wire from the fan has four wires, the wire with the plug has four wires. They share three, of the four colors: red, black, and blue. Dell's fourth wire is white, while the plug's fourth wire is yellow. Is it safe to assume that I just connect the yellow and the white plug together and match the rest up? I don't want to take any risk of damaging anything. It runs fine passively without a fan, but I have speedstep on, so I would like to use this fan and just fasten it to the heatsink with some twist ties and paperclips and call it a day.

    Read the article

  • Windows XP corrupts registry every several hours

    - by Ilya Kazakevich
    There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

    Read the article

  • Windows XP corrupts registry every several hours

    - by Ilya Kazakevich
    There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

    Read the article

  • x display problems in centos 5.5

    - by John Ruiz
    I have a Dell E510 desktop with a geForce 7200 instead of the ATI x600 it came with. I have attempted to install CentOS 5.4 x86_64 (DVD), CentOS 5.5 (net install), and CentOS 5.5 x86_64 (DVD). Gnome desktop. All of these run into the same issue. When I put the DVD into the machine and reboot, the installer begins and I select "graphical install". I see text that say anaconda is starting, and then my screen goes nuts. It's not black, but rather a screen full of diagonal stripes or multiple colors. So I attempted to do a text install of CentOS 5.5 (DVD) and got it installed. When I booted for the first time, I logged into the virtual console and started X (startx). The desktop came up and it already had the display properties GUI up. I changed it from 800x600 to 1680x1050, saw that there were updates available, installed them, and then rebooted. When I start X from the virtual console this time, I get exactly the same display problem as I described before. Does anyone know what might be causing this and what I can do about it? edit: I should also mention that I'm capable of installing Windows 7 and Ubuntu 10.04 onto this machine with absolutely no issues at all.

    Read the article

  • How to crop Screen Recordings under Snow Leopard?

    - by willc2
    Quicktime Player for Snow Leopard now allows you record the screen. Awesome! Once you have a movie it will let you trim screen recordings for length. Is there a way to crop the movie's dimensions, either in QT or using some built-in or free software? Update: How to crop to an arbitrary size and aspect ratio? iMovie only seems to let you crop to the aspect ratio of the containing project. Result: Both good answers but since I have QuickTime Player 7 and Photoshop, that's the workflow I choose as the answer. NOTE: If you have Photoshop Extended, you can import a movie, use the crop tool, and Export the cropped movie. Not free or built-in, but convenient. To summarize the instructions from the video link ricbax posted: Open movie in QuickTime Player 7 Copy a frame and Paste it into a new document in Photoshop Draw a rectangular selection around the area to keep and fill with black Invert the selection and fill with white Save as .GIF, with 2 colors Back in QuickTime Player 7, open Movie Properties window Select the Video Track Select the Visual Settings Tab Drag and Drop the 2-color .GIF file onto the Mask drop area (or use choose file button) Export the (now cropped) movie DONE

    Read the article

  • How do I improve my screen resolution in Windows Remote Desktop?

    - by Jeff
    I'm RDP'ing into a Win2K3 machine from a WinXP machine, and I cannot stand the low screen resolution I get on the Win2K3 box. Text is too large and the graphics/colors aren't very smooth. How do I improve this? If I right-click on the desktop of the remote machine and go to Properties - Settings, I see that the screen resolution is set to 1280x1024 (should be okay, I would think), and the color quality is Medium (16 bit) (not optimal) and I don't have the option to change either setting (because they're set in the .rdp file for the session, right?). If I move over to the Appearance tab, I see that font size is set to Normal, with no option to make it smaller. The thing is, these settings are close to what I have on the XP machine I'm RDP'ing in from. The only difference (in those settings) is the color quality, which is 32 bit. Any ideas on how I can improve the situation? Other tidbits: The graphics card on the Win2K3 machine is ATI ES1000. I think I have the latest drivers for it. I'm running VMware Workstation on the Win2K3 machine, and if I create a Win2K3 VM and RDP into it from the XP machine, the resolution is just fine.

    Read the article

  • java.lang.ArrayIndexOutOfBoundsException

    - by thefonso
    Here is the code. import java.applet.Applet; import java.awt.Button; import java.awt.Color; import java.awt.Graphics; import java.awt.event.ActionEvent; import java.awt.event.ActionListener; public class GuessingGame extends Applet{ /** * */ private static final long serialVersionUID = 1L; private final int START_X = 20; private final int START_Y = 40; private final int ROWS = 4; private final int COLS = 4; private final int BOX_WIDTH = 20; private final int BOX_HEIGHT = 20; //this is used to keep track of boxes that have been matched. private boolean matchedBoxes[][]; //this is used to keep track of two boxes that have been clicked. private MaskableBox chosenBoxes[]; private MaskableBox boxes[][]; private Color boxColors[][]; private Button resetButton; public void init() { boxes = new MaskableBox[ROWS][COLS]; boxColors = new Color[ROWS][COLS]; resetButton = new Button("Reset Colors"); resetButton.addActionListener(new ActionListener() { public void actionPerformed(ActionEvent e) { randomizeColors(); buildBoxes(); repaint(); } }); add(resetButton); //separate building colors so we can add a button later //to re-randomize them. randomizeColors(); buildBoxes(); } public void paint(Graphics g) { for (int row =0; row < boxes.length; row ++) { for (int col = 0; col < boxes[row].length; col++) { if(boxes[row][col].isClicked()) { //boxes[row][col].setMaskColor(Color.black); //boxes[row][col].setMask(!boxes[row][col].isMask()); //boxes[row][col].setClicked(false); //} if (!matchedBoxes[row][col]) { gameLogic(boxes[row][col]); //boxes[row][col].draw(g); } } } } //loop through the boxes and draw them. for (int row = 0; row < boxes.length; row++) { for (int col = 0; col < boxes[row].length; col++) { boxes[row][col].draw(g); } } } public void gameLogic(MaskableBox box) { if ((chosenBoxes[0] != null)&&(chosenBoxes[1] != null)) { if(chosenBoxes[0].getBackColor() == chosenBoxes[1].getBackColor()) { for (int i=0; 0 <= chosenBoxes.length; ++i ) { for(int row = 0; row < boxes.length; row++) { for(int col = 0; col < boxes[row].length; col++) { if( boxes[row][col] == chosenBoxes[i] ) { System.out.println("boxes [row][col] == chosenBoxes[] at index: " + i ); matchedBoxes[row][col] = true; break; } } } } }else { chosenBoxes[0].setMask(true); chosenBoxes[1].setMask(true); } chosenBoxes = new MaskableBox[2]; }else { if (chosenBoxes[0] == null) { chosenBoxes[0] = box; chosenBoxes[0].setMask(false); return; }else{ if (chosenBoxes[1] == null) { chosenBoxes[1] = box; chosenBoxes[1].setMask(false); } } } } private void removeMouseListeners() { for(int row = 0; row < boxes.length; row ++) { for(int col = 0; col < boxes[row].length; col++) { removeMouseListener(boxes[row][col]); } } } private void buildBoxes() { // need to clear any chosen boxes when building new array. chosenBoxes = new MaskableBox[2]; // create a new matchedBoxes array matchedBoxes = new boolean [ROWS][COLS]; removeMouseListeners(); for(int row = 0; row < boxes.length; row++) { for(int col = 0; col < boxes[row].length; col++) { boxes[row][col] = new MaskableBox(START_X + col * BOX_WIDTH, START_Y + row * BOX_HEIGHT, BOX_WIDTH, BOX_HEIGHT, Color.gray, boxColors[row][col], true, true, this); addMouseListener(boxes[row][col]); } } } private void randomizeColors() { int[] chosenColors = {0,0,0,0,0,0,0,0}; Color[] availableColors = {Color.red, Color.blue, Color.green, Color.yellow, Color.cyan, Color.magenta, Color.pink, Color.orange }; for(int row = 0; row < boxes.length; row++) { for (int col = 0; col < boxes[row].length; col++) { for (;;) { int rnd = (int) (Math.random() * 8); if (chosenColors[rnd]< 2) { chosenColors[rnd]++; boxColors[row][col] = availableColors[rnd]; break; } } } } } } here is the second batch of code containing maskablebox import java.awt.Color; import java.awt.Container; import java.awt.Graphics; public class MaskableBox extends ClickableBox { private boolean mask; private Color maskColor; Container parent; public MaskableBox(int x, int y, int width, int height, Color borderColor, Color backColor, boolean drawBorder, boolean mask, Container parent ) { super(x, y, width, height, borderColor, backColor, drawBorder, parent); this.parent = parent; this.mask = mask; } public void draw(Graphics g) { if(mask=false) { super.draw(g); // setOldColor(g.getColor()); // g.setColor(maskColor); // g.fillRect(getX(),getY(),getWidth(), getHeight()); // if(isDrawBorder()) { // g.setColor(getBorderColor()); // g.drawRect(getX(),getY(),getWidth(),getHeight()); // } // g.setColor(getOldColor()); }else { if(mask=true) { //super.draw(g); setOldColor(g.getColor()); g.setColor(maskColor); g.fillRect(getX(),getY(),getWidth(), getHeight()); if(isDrawBorder()) { g.setColor(getBorderColor()); g.drawRect(getX(),getY(),getWidth(),getHeight()); } g.setColor(getOldColor()); } } } public boolean isMask() { return mask; } public void setMask(boolean mask) { this.mask = mask; } public Color getMaskColor() { return maskColor; } public void setMaskColor(Color maskColor) { this.maskColor = maskColor; } } I keep getting these error messages. I'm going nuts trying to figure this out. can anyone tell me what I'm doing wrong? boxes [row][col] == chosenBoxes[] at index: 0 boxes [row][col] == chosenBoxes[] at index: 1 Exception in thread "AWT-EventQueue-1" java.lang.ArrayIndexOutOfBoundsException: 2 at GuessingGame.gameLogic(GuessingGame.java:77) at GuessingGame.paint(GuessingGame.java:55) at java.awt.Container.update(Container.java:1801) at sun.awt.RepaintArea.updateComponent(RepaintArea.java:239) at sun.awt.RepaintArea.paint(RepaintArea.java:216) at sun.awt.windows.WComponentPeer.handleEvent(WComponentPeer.java:306) at java.awt.Component.dispatchEventImpl(Component.java:4706) at java.awt.Container.dispatchEventImpl(Container.java:2099) at java.awt.Component.dispatchEvent(Component.java:4460) at java.awt.EventQueue.dispatchEvent(EventQueue.java:599) at java.awt.EventDispatchThread.pumpOneEventForFilters(EventDispatchThread.java:269) at java.awt.EventDispatchThread.pumpEventsForFilter(EventDispatchThread.java:184) at java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java:174) at java.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:169) at java.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:161) at java.awt.EventDispatchThread.run(EventDispatchThread.java:122)

    Read the article

  • Why Does DreamWeaver CS5 Discriminate between File Extensions, Even After Modding Mime Types!?

    - by Sam
    Hi folks, Even After I forced DreamWeaver CS5 to allow opening of .ast extensions as a MIME type of php5, which DreamWeaver now opens and colors correctly as described here, I still have trouble figuring out why it still discriminates between the two file extensions! Symptoms: External Files & Design View I have a file foo.php which php includes other files (e.g. the php-combined css.php and js.php). Now, when opening foo.php all functions work perfectly: the external (included) php files are all recognised correctly. However, when I change foo.php foo.ast, and open it again, It does not recognise the files extensions anymore in the top bar. Also, I lose the Design / Live View functionality.** When I change foo.ast to foo.php, all works again! Anyone any clues of why there remains a a difference between one and other extension? Note1: I have added the .ast extension to these four files, next to .php: 1 C:\Users\Sam\AppData\Local\VirtualStore\Program Files (x86)\Adobe\Adobe Dreamweaver CS5\configuration\DocumentTypes\MMDocumentTypes.xml 2 C:\Program Files (x86)\Adobe\Adobe Dreamweaver CS5\configuration\DocumentTypes\MMDocumentTypes.xml 3 C:\Users\Sam\AppData\Roaming\Adobe\Dreamweaver CS5\en_US\Configuration\Extensions.txt 4 C:\Program Files (x86)\Adobe\Adobe Dreamweaver CS5\configuration\Extensions.txt Note2: sometimes, even .php files do not want to show in design view or live view. Could this be caused by a corrupted installation?

    Read the article

  • RDP Connection to Windows 7 stays really slow

    - by Pavlo
    I have an Issue with connecting to Windows 7 via RDP. I can open an RDP Session, but regardless of any settings, the responce times are really long. This in particulary is the case when opening a web page in a browser. I've tried IE, Firefox and Google Chrome. I also use RDP connection to a Windows 2008 Server from the same client machine, and the speed is very normal with all features turned on. We have Gigabit Ethernet here. So I think it can not be the client's fault. What concerns Windows 7 Machine, I've tried shutting all the sraphic features off and turning the color levels to 256 colors. Result - the same. If I work locally on the machine - I can not see any lags. What else have I tried: Using old RDP 5 Client from Microsoft Setting network autotuninglevel as seen here Do You have some ideas? Thanks in advance! Update the problem seems to be with rendering window contents. All the window borders and pannes are rendered pretty quickly, but the content shows up very slowly. Also mouse movements are recognised by the Win 7 box only after some period. Are there some hidden settings in the RDP, where one could turn some advanced features off or turn some caching on? I use Bitmap Caching, but this apparently doesn't help.

    Read the article

  • Cannot set video resolution above 640x480 after installing Windows XP SP2

    - by waanders
    I've installed Windows XP SP2 on a computer (there was not SP at all). Now the display settings are set back to 640x480 and 4 bits colors. And I can't change it, it's the only option in Settings tab of the Display dialog of Windows. The screen look awful now, how can I solve this problem? UPDATE: Seems to be a problem with the video driver (thanks @Karan and @Hennes). I did run Speccy (PC-Wizard freezes the computer) and this is a part of the log file: Summary Operating System Microsoft Windows XP Professional 32-bit SP3 CPU Intel Celeron Willamette 0.18um Technology RAM 512 MB DDR @ 133MHz (2.5-3-3-6) Motherboard COMPAQ 0838h (FC-478) Graphics Standard Monitor (640x480@1Hz) Hard Drives 19.0GB Maxtor 2B020H1 (PATA) Optical Drives No optical disk drives detected Audio No audio card detected ... Graphics Monitor Name Standard Monitor on Current Resolution 640x480 pixels Work Resolution 640x450 pixels State enabled, primary Monitor Width 640 Monitor Height 480 Monitor BPP 4 bits per pixel Monitor Frequency 1 Hz Device \\.\DISPLAY1 OpenGL Version 1.1.0 Vendor Microsoft Corporation Renderer GDI Generic GLU Version 1.2.2.0 Microsoft Corporation Values GL_MAX_LIGHTS 8 GL_MAX_TEXTURE_SIZE 1024 GL_MAX_TEXTURE_STACK_DEPTH 10 GL Extensions GL_WIN_swap_hint GL_EXT_bgra GL_EXT_paletted_texture GL_EXT_bgra

    Read the article

  • Numbering grouped data in Excel

    - by Jeff
    I have an Excel spreadsheet (2010) with data similar to this: Dogs Brown Nice Dogs White Nice Dogs White Moody Cats Black Nice Cats Black Mean Cats White Nice Cats White Mean I want to group these animals but I only care about species and color. I don't care about disposition. I want to assign group numbers to the set as shown here. 1 Dogs Brown Nice 2 Dogs White Nice 2 Dogs White Moody 3 Cats Black Nice 3 Cats Black Mean 4 Cats White Nice 4 Cats White Mean I was able to select all the species and colors, then from the data tab select 'advanced', then 'unique records only'. This collapsed the data so that I could number the visible rows. Then when I 'cleared' the filter I could easily just fill the blank areas under the numbers with the number above. The problem is that my real data has far too many rows for this to be practical. Also, the trick about entering 1 in the first cell, 2 in the cell below, selecting both then dragging the corner down to 'auto-number' doesn't seem to work when you're viewing filtered rows. Any way to do this?

    Read the article

  • Keeping Xv Overlay configuration throughout an X session.

    - by kriss
    After upgrading my Linux system from Ubuntu 9.04 to Ubuntu 10.10, I suceeded correcting most problems (all related to Intel 82865G Integrated Graphics Adapter support and compiz is still not working but that's another matter) but for one I only have a partial solution. Whenever I play a video the colors are much too saturated. This is really a problem for tones of skins that appears reddish (everyone seems to be coming back from a ski vacation with deep sun burns). As this effect only occurs with videos, not with pictures, I finally figured out it was related to Video Overlays configuration and I can correct it typing: xvattr -a XV_SATURATION -v 120 This change the default saturation value, which is 500 and much too high in my case, at eye sight the correct value seems to be between 100 and 150. Now my problem is that I have to type the above command each time I run a video. If I type it before running the video it has no effect, if I close the video and open a new one, I have to type it again, etc. I tried to put it in Xsession and (logically) it has no effect either. How could I do to get the correct setting whenever I run a video without typing the above command every time ?

    Read the article

  • Is it possible to have a conditional formatting cell "visually cycle" through all the formats that evaluated true?

    - by Ben
    Like the title says, "In Excel, when a cell has multiple conditional formatting rules that evaluate true, is it possible to have the cell "visually cycle" through all the formats that evaluated true? If not, suggestions on what to do would be appreciated!" I'm creating an employee schedule for a business that has multiple job areas that need to have an employee assigned to cover. The schedule is currently set up with the date on the top row, employee list down the left column, and the employee's assigned "job area" cross-referencing with the date on the top row. Originally it was set up where if every required "job area" didn't have someone assigned to it, the date would (via conditional formatting) change to red. I've set it up now that if a condition isn't met, the date will change to the color of the "job area" that doesn't have an employee assigned to it. However, there are cases where multiple job areas don't have an employee assigned, but the date will only change color based on the first condition that isn't met. It'd be nice if there was some way for the date cell to cycle through the different colors that correspond to the job areas where no one is assigned. I have a hunch that's not possible though. If it is possible, I'd love to know how to do it. And if it isn't, if anyone has any suggestions on how I can modify the Excel sheet to make it easier to identify the job areas that don't have anyone assigned to them, I would appreciate it. FYI This schedule goes out months in advance.

    Read the article

  • Is having a [high-end] video card important on a server?

    - by Patrick
    My application is quite interactive application with lots of colors and drag-and-drop functionality, but no fancy 3D-stuff or animations or video, so I only used plain GDI (no GDI Plus, No DirectX). In the past my applications ran in desktops or laptops, and I suggested my customers to invest in a decent video card, with: a minimum resolution of 1280x1024 a minimum color depth of 24 pixels X Megabytes of memory on the video card Now my users are switching more and more to terminal servers, therefore my question: What is the importance of a video card on a terminal server? Is a video card needed anyway on the terminal server? If it is, is the resolution of the remote desktop client limited to the resolutions supported by the video card on the server? Can the choice of a video card in the server influence the performance of the applications running on the terminal server (but shown on a desktop PC)? If I start to make use of graphical libraries (like Qt) or things like DirectX, will this then have an influence on the choice of video card on the terminal server? Are calculations in that case 'offloaded' to the video card? Even on the terminal server? Thanks.

    Read the article

  • Acer recovery disks not bootable?

    - by user13743
    We got a new Acer laptop with Vista installed at work. As it's getting ready to go out in the field, we wanted to do a burn-in test on it. We made the recovery DVDs before we ran the test. Part of the burn-in was bonnie++, which does a destructive read/write test of the hard drive. The machine passed with flying colors, but after trying to boot to the recovery DVD to being re-installing the system, the machine began to try PXE boot after a while. After doing some googling, it appears these 'recovery' disks expect a certain recovery partition to exist on the hard drive, and are in fact not bootable at all, and are useless in absence of the recovery partition. Is this the case, and is this "The Way Things Are" with all PC manufacturers and Windows Vista+ nowadays? How do I get my hands on actual bootable DVDs? I've emailed Acer support. I see an option on their site to purchase recovery disks, but I have the suspicion that these are the same non-bootable disks that I burned on the new system. Will Acer provide actual boot disks?

    Read the article

  • Can I use @import to import Kod's default style sheet into my own?

    - by Thomas Upton
    I understand that Kod is being actively developed and is prone to drastic changes in any area. I would like to modify some small things (like font face and size or certain colors) while still being able to benefit from any changes or updates to the default Kod stylesheet. I thought that I would be able to @import the default stylesheet into my own to achieve this. This is what ~/.kod/custom.css would look like, @import url("file:///Applications/Kod.app/Contents/Resources/style/default.css"); /* Change the default font face and color. */ body { font-family: Menlo, monospace; color: #efefef; } This stylesheet was set with the following defaults command, per the comments at the top of Kod's default CSS file: defaults write se.hunch.kod style/url ~/.kod/custom.css Unfortunately, this didn't work. When I first tried to reload the style, Kod crashed. It opened fine again, but the @import statement wasn't working, and Kod crashed every time I saved the custom.css file. Am I doing something wrong? Did I write my @import statement wrong? Is that not how @import is supposed to work? Did I miss some sort of documentation or Kod Google Groups post that mentions that Kod explicitly disallows this?

    Read the article

  • Lookup Multiple Results for Multiple Criteria

    - by Matt
    I've got a list of parent SKUs for items I need to create in my inventory system. This list has been finely paired down to the 165 products we would like to carry. However, each one of these 165 SKUs has between 2 and 8 child SKUs of different colors, sizes, etc. Those are stored on a different worksheet, mixed into around 2500 items. Those are the SKUs I need to input into my inventory system. Here is what it looks like. Sheet 1 is just SKUs: A 1 2 3 4 Sheet 2 is comprised of all the child SKUs, with parent SKUs in column B. Not all parents have the same number of children: A B 1BLKM 1 1BLKL 1 1BLUM 1 2BLKM 2 2BLKL 2 2BLUM 2 2ORAM 2 3BLKM 3 3BLUM 3 I want to look up all of the child SKUs for the Parent SKU list that has been fine tuned. Parent SKU is included as a column on the child SKU worksheet. I need to lookup all matches of the Parent SKU, then continue to move down the parent SKU list until all matches for all 165 parent items have been found. It seems like every function I try can't use an Array for input. Is there a way to do this with Lookup or some combination of index, match, row, etc? Any way at all to do it without VBA? Or maybe even a VBA solution with code that I can understand, as someone who hasn't used VBA before.

    Read the article

  • Photoshop CS4. How do I make sure my color stays the same in my different .psd files? (could be RGB

    - by Kris
    I asked 2 photoshop experts I know but they haven't got a clue because all my settings are exactly the same, in both files. (except the RGB type !! I'm not sure. Please read on) I use RGB color, 72DPI, 8 bits / channel. No adjustments (filters, like greyscale, etc ...) are selected / used. The layers are both normal, and opacity and fill are 100% (yes, in both files). I took two screenshots, and you can see the difference: http://www.flickr.com/photos/30465871@N05/4623864297/ http://www.flickr.com/photos/30465871@N05/4624469754/ Both colors are ff795d, but that doesn't matter, any color I use gives me the same problem: they both look different. Now, I know the CMYK settings (see screenshots) are different, but when the settings are the same the color changes. Why is this happening and how do I solve this problem? My guess is I'm working with different a type of RGB. It's sRGB IE61966 - 2.1 in the file I created (file info raw data) but I can't find that in the file that started with a screenshot. If that's the problem, how do I change / convert the RGB, once the file is already open? Thank you.

    Read the article

  • RDP Connection to Windows 7 stays really slow

    - by Pavlo
    I have an Issue with connecting to Windows 7 via RDP. I can open an RDP Session, but regardless of any settings, the responce times are really long. This in particulary is the case when opening a web page in a browser. I've tried IE, Firefox and Google Chrome. I also use RDP connection to a Windows 2008 Server from the same client machine, and the speed is very normal with all features turned on. We have Gigabit Ethernet here. So I think it can not be the client's fault. What concerns Windows 7 Machine, I've tried shutting all the sraphic features off and turning the color levels to 256 colors. Result - the same. If I work locally on the machine - I can not see any lags. What else have I tried: Using old RDP 5 Client from Microsoft Setting network autotuninglevel as seen here Do You have some ideas? Thanks in advance! Update the problem seems to be with rendering window contents. All the window borders and pannes are rendered pretty quickly, but the content shows up very slowly. Also mouse movements are recognised by the Win 7 box only after some period. Are there some hidden settings in the RDP, where one could turn some advanced features off or turn some caching on? I use Bitmap Caching, but this apparently doesn't help.

    Read the article

  • Connecting a laptop to a TV via HDMI

    - by Madmartigan
    I just bought a new Dell XPS17 laptop (Win7) that only has HDMI output. My last 2 laptops had VGA, which I used to connect to my Sony Bravia 32" TV with no issues, but with the HDMI it's been quite a headache. Drivers for display adapters have been updated to the latest versions: Intel(R) HD Graphics Family NVIDIA GeForce GT 550M I went to a store and plugged in to 4 different TVs from different manufacturers. A sales rep and I spent about 30 minutes being baffled by the results (which are the same as my current TV): Extreme buggy behavior in the Nvidia and Windows display/resolution control panel Can not extend or duplicate displays, can only select one Third and fourth output devices "randomly" detected by the Windows control panel Could not get the screen to fit the output (edges cut off on all sides by about a half inch) Resolution and colors less than perfect. Artifacts around text. Display "randomly" cuts out Defaults to TV output only when plugged in Can not change resolution on either device when connected No audio from the TV Plugged in to 3 monitors from different manufacturers: Defaults to duplicated displays when plugged in Everything works perfectly So far, four people have gone through all the settings in the latop with no luck. I had similar, but not exactly matching results with a different laptop. I'm using the Sony Bravia currently at home, but in order to get it to work I have to turn on the laptop, wait until the display shows up on it, close the lid, then cycle through each output channel on the TV until I come back around to the HDMI port again, but still I have the symptoms described above. However: Once in a while, it just works. Sometimes, seemingly randomly, the output fits the screen perfectly. Sometimes the audio comes through the speakers too, but not always. Usually my screen saver "Mystify" will come up with a message that it cannot be displayed due to a limitation of the video card, but then sometimes it works fine. These 3 things seem to be independent of each other and don't always happen together. So, is there any way to get the laptop to output correctly to a TV, or is it just not meant to be?

    Read the article

  • how to diagnose a hard system seizure? Dell+Ubuntu

    - by rob
    I've got Ubuntu 9.10 on a Dell Vostro 420 desktop, a little over a year old, which I use for plain vanilla work stuff (email, web, terminal, text editor). Every now and then, at totally random times, it completely freezes on me. Hard. Mouse and keyboard stop working, cursor stops blinking, clock stops moving. All I can do is hold down the power button on the front of the box to shut it off. Sometimes it happens after several months of continuous uptime; sometimes it happens a few minutes after a reboot, while all I've done is open a terminal to look at log files, or maybe firefox to do a google search. Each time, there is nothing at all in /var/log/messages at the time of the crash. This makes it seem like a hardware problem, and indeed a few months ago I opened the box and wiggled everything and the problem went away for a while. But now it's back. I went in and checked everything, took out each RAM card and reseated. No luck. I ran all the system diagnostics (the long version) and everything passed with flying colors. Something is messed up in this box, but without any useful logs or failed tests, how in the world am I going to find it? And of course, Dell's not gonna help me cause I went and replaced Windows with Ubuntu. What steps would you take next to track down this problem?

    Read the article

  • How I can fix the "Display Driver has stopped responding and has recovered"?

    - by Vitor Rangel
    I'm using a GeForce GTX 580, with Windows 7 64-bit. The driver version of the GTX is 301.42. The problem happens after a few minutes, when I'm playing specifc games. It won't happen in all games - And I don't have any idea why these games doesn't work. The games that doesn't work: Battlefield 3, Civilization V, Sniper Elite V2. The games that work: Mass Effect 3, Crysis 2, Team Fortress 2, Left 4 Dead 2, Skyrim, L.A. Noire. As you can see, it's not a problem of "The games that demand more stop working". I've tryed updating the driver of the graphics-card, the bios of the motherboard, even formated my computer (It was needing it) and instaled every driver in the last version possible. This problem happens since I bought my graphics-card, 6 months ago. After a few minutes, from 10 to 20, the pixels in the monitor become strange, with random colors and effects, like it was broken. Then, everything goes black, and the message appears "Display Driver has stopped responding and has recovered". After that, I need to close the game and start again. I am not overclocking, and my temperature never goes higher than 70ºC.

    Read the article

  • Why do moving lines become fuzzy on my monitor?

    - by CodeInChaos
    I recently got a new notebook. With moving images there are some graphical issues, and I'd like to know what causes them. None of my earlier monitors exhibited similar issues. Moving high contrast lines become jagged, similar to interleaved videos. When moving a horizontal line vertically those artifacts are colored, when moving a vertical line horizontally they aren't colored. The effect isn't observable in static images. And when moving faster the zone in which it occurs becomes wider. The effect is very visible if I move a window around on the borders of the window and wherever high contrast lines appear. But it appears when watching videos too. The vertical line in that image moves to the right, the horizontal line upwards. The effect is most likely related to the fact that each real pixel consists of different sub-pixels for the different color channels. But how are these causing the observed effect? Is the change at which the different colors change to the destination brightness different? The optical impression is that every second pixel in a chess board like arrangement is adapting slower than it's neighbors. But that doesn't make much sense.

    Read the article

  • Multiple Settings for One Monitor

    - by Lynda
    I have my monitor set to the way I like it, it shows colors accurately and not overly bright (white doesn't blind me). However I edit photos for the web and this is great for my screen but I have noticed when looking at other screens my photos will at times looked washed out and not a good presentation. If I manually change my monitor settings to be brighter (and a few other tweaks) I can replicate the look of other monitors close enough to help prevent washed out/blown out photos. Here is the issue, I need to be able to change settings between the two fairly easily. To manually set my monitor for one then back to the other can be time consuming and a pain to set right every time. I would like to be able to preset certain settings (in software) that I can quickly switch between by pressing hotkeys or clicking shortcut on my desktop. I have an AMD video card and have attempted to use the AMD VISION Engine Control Center to add presets then tweak the settings for each. However when I switch between the presets the settings are the same. How do I build presets using the VISION Engine Control Center that actually works (maybe I misunderstand what it is saving?) or is there a way to do this in Windows 7 or free software that actually works decently for this purpose?

    Read the article

  • Graphics artifacts/distortion with Win7 and nVidia

    - by Gepard
    Problem I encounter is rather hard to describe, so I provide a screenshot: http://dl.dropbox.com/u/1732760/video-distortion.png As you can see there are some horizontal stripes in random colors. These stripes appear sometimes in all windowed apps, games and on the desktop too. They tend to stay in place until I refresh window (or force it to to redraw by for example minimizing and maximizing again). They also tend to appear in the same place and shape multiple times, even if they disappear, it's very likely they will be again in the same place after a while. These artifacts do not blink or change if computer is idling. If I don't touch anything, do not use mouse, they will stay in place forever (unless some app redraws its window on its own). I first encountered this problem some weeks ago. Back then I thought it might be cooling problem, so I took out the graphics card, removed dust from the radiator and fan and put it into PC back. I also ran some stress test using Furmark (peak tempearature was ~65C) to see if the problem becomes more intense if the card gets hotter, but suprisingly no artifacts whatsoever appear during the stress test. Graphic card is Galaxy GeForce 7300 GT with DDR3 memory, was never overclocked. Drivers are the latest, from Nvidia site. OS is Windows 7 64-bit, updated. AMD64 3000+, 2GB RAM. I'm running a dual monitor setup with 2 19'' Samsung LCDs and problem is on both, so I assume it's not a monitor or cable issue.

    Read the article

< Previous Page | 49 50 51 52 53 54 55 56 57 58 59 60  | Next Page >