Search Results

Search found 4681 results on 188 pages for 'john shore'.

Page 53/188 | < Previous Page | 49 50 51 52 53 54 55 56 57 58 59 60  | Next Page >

  • How to disable SSL 2.0 on IIS 7.5?

    - by John Hoge
    I've seen this KB Article which Microsoft put out covering how to remove SSL 2.0 on IIS 7.0 and earlier, but I can't find anything advising on how to do the same on IIS 7.5. The registry keys mentioned on that KB article are no longer in the registry.

    Read the article

  • How to control admission policy in vmware HA?

    - by John
    Simple question, I have 3 hosts running 4.1 Essentials Plus with vmware HA. I tried to create several virtual machines that filled 90% of each server's memory capacity. I know that vmware has really sophisticated memory management within virtual machines, but I do not understand how the vCenter can allow me even to power on the virtual machines that exceed the critical memory level, when the host failover can be still handled. Is it due to the fact that virtual machines does not use the memory, so that it is still considered as free, so virtual machines can be powered on ? But what would happen if all VMs would be really using the RAM before the host failure - they could not be migrated to other hosts after the failure. The default behaviour in XenServer is that, it automatically calculates the maximum memory level that can be used within the cluster so that the host failure is still protected. Vmware does the same thing ? The admission policy is enabled. Vmware HA enabled.

    Read the article

  • "tasksel: aptitude failed (100)" installing LAMP on Ubuntu (vagrant)

    - by John Mee
    vagrant@precise64:~$ sudo tasksel install lamp-server tasksel: aptitude failed (100) I'm hoping to get a LAMP server from a clean install of ubuntu. All the googles suggest tasksel, which going into a pretty ascii gui, downloads stuff, then dies with this message. I'm guessing I should try doing it via apt-get of the individual packages but seems a fair chance somebody else is going to search for this error message and want the right answer.

    Read the article

  • SSLCipherSuite - disable weak encryption, cbc cipher and md5 based algorithm

    - by John
    A developer recently ran a PCI Scan with TripWire against our LAMP server. They identified several issues and instructed the following to correct the issues: Problem: SSL Server Supports Weak Encryption for SSLv3, TLSv1, Solution: Add the following rule to httpd.conf SSLCipherSuite ALL:!aNULL:!eNULL:!LOW:!EXP:RC4+RSA:+HIGH:+MEDIUM Problem: SSL Server Supports CBC Ciphers for SSLv3, TLSv1 Solution: Disable any cipher suites using CBC ciphers Problem: SSL Server Supports Weak MAC Algorithm for SSLv3, TLSv1 Solution: Disable any cipher suites using MD5 based MAC algorithms I tried searching google for a comprehensive tutorial on how to construct an SSLCipherSuite directive to meet my requirements, but I didn't find anything I could understand. I see examples of SSLCipherSuite directives, but I need an explanation on what each component of the directive does. So even in the directive SSLCipherSuite ALL:!aNULL:!eNULL:!LOW:!EXP:RC4+RSA:+HIGH:+MEDIUM, I dont understand for example what the !LOW means. Can someone either a) tell me the SSLCipherSuite directive that will meet my needs or b) show me a resource that clearly explains each segment of a SSLCipherSuite is and how to construct one?

    Read the article

  • Gateway GT5220 Boot/POST Failure

    - by John Rudy
    I have a Gateway GT5220 I'm troubleshooting. It is, in fact, the machine I just gave my father for his birthday a couple months ago. (Prior to that, it was my home PC. My home PC is now the MacBook on which I'm writing this.) Before going any further, I suspect that the answer will be, "It's worse than that, it's dead, Jim, it's dead, Jim, it's dead, Jim." At least, mobo and/or CPU. The initial symptoms were as follows: Turn on power All fans fire up (thus making it so I can't hear if the hard drive is spinning or not, nor are my hands sensitive enough anymore to feel it) No LEDs remained lit on the front panel. (Initially, the hard drive indicator flashed briefly.) No beep, no video, no nothing. Following some advice I found here, I tried to "drain the stored power." After following those steps, the new symptoms were: Turn on power All fans fire up The front panel LEDs remained lit! After about 20, maybe 30 seconds, we had video! Sort of. We got to the Gateway splash/POST screen, which appeared thoroughly corrupted. How corrupted? Well, I imagine it's what a POST screen would look like after reading the wrong passage out of the Necronomicon: It stayed there. I gave it at least 5, maybe 6 minutes, and it didn't move. So I shut her down, started her up again, and now (this is where we currently stand, symptomatically) we have this: Turn on power All fans fire up The front panel LEDs remain lit No video, no beep, no nothing. I'm a software guy; haven't done real hardware troubleshooting in years. My gut tells me that the mobo and/or CPU is fried, and unfortunately my gut didn't get to be as big as it is being wrong all the time. :( In addition to the link above, I have read all of the following (trying to save you some LMGTFY trouble): Gateway Support POST Error Messages and Handling About a zillion (useless) POST beep code sites A kioskea.net post indicating that most likely we're at what I consider "total loss" (mobo and/or CPU) My questions: Are there any conditions other than mobo/CPU that could cause symptoms like these? Is it worth my time to try the next hardware troubleshooting step?(IE, remove all non-critical hardware from the machine, try to boot, systematically replace one by one until we find the failing component) Which mobos will fit in the Gateway GT5220 case (with rear ports correctly aligned)? (Why this is not a dupe: I wouldn't have posted this question if it hadn't been for the funkadelic possessed video display on the one occasion we got video out. I think that justified this not being an exact dupe. Of course, if the community overrules, I will understand.)

    Read the article

  • Disaster After Removing Two HDD From LaCie RAID 0 Case

    - by John
    This is the second time this has happened. I own a LaCie IDE RAID 0 Enclosure and the RAID went bad. The system gave me a warning that the data could be read from the RAID but that nothing could be written, and to remove the data ASAP. I did that and erased and reinitialized the RAID. System reported it was fine, no issues. I wrote to the RAID again and the system reported the same issue. So, I removed the drives and tested them individually thinking one must have gone bad. Sure enough, one HDD reported all bad blocks, every single one after the Master Boot Record. I didn't think much about it because of the age of the drives, 5 years old. So, I bought two new drives plugged them in and started up the RAID again. Exactly the same thing happened. All was fine after initializing the RAID and then the next day after powering on the RAID the exact same issue. The HDD sitting in the same position as the first "bad" HDD reported all bad blocks. Obviously, this is an issue with LaCie's bridge board not with the drives. No utility I have used has been able to bring this HDD back to life. I thought I would just copy the MBR from the good drive to the new one using a sector editor but am hesitant. Is it possible the firmware on the HDD has been corrupted by the LaCie bridge board?? What else could be the cause of such an issue? How can I fix this drive?

    Read the article

  • Linking FreeNAS Boxes

    - by John
    I have two different FreeNAS boxes that are being used for storage. It is possible to link them in a manner that the linked connection can be presented as a single storage destination for clients? For example, I have one FreeNAS installation that has 6 TB of storage and another one that has 4 TB of storage. I would like to be able to present or have a single mapped drive for clients that would be able to span across both of them; however, the client would only see it as one drive. Is this possible? If not, is there a different way I should be approaching this problem? Is there a different OS distribution that would work better for this?

    Read the article

  • iRedMail home setup - use different SMTP relay for different destination domains

    - by John
    Hello helpful server folks, I'm messing with iRedMail. I've mostly been successful, I think I have an SMTP problem. I have changed RoundCube (webmail) to use BrightHouse's, my ISP's, SMTP server for outgoing. It works fine, I click send and poof, I have gmail. I can reply from gmail to my email server, and it works. It took 10 hours for the email to show up, which is a different problem, I think, but it does work. But when I send from my server TO my own server, my ISP's Postmaster account sends me a cryptic blurb. I just got off the phone with them, and they say it "should work", and that they can't reach my pop3 server. (pop3, pop3s, imap, and imaps are all open on my router and forwarded to the server, I'm not sure what I need, I'm just covering my bases...) pop3 and/or imap as external interfaces are just formalities, I really just want webmail to work. Roundcube only takes one SMTP server in its configs. How can I configure Postfix to relay / forward emails to my ISP's SMTP, while taking messages bound for my own domain and processing them? Since my ISP won't let me "bounce" my emails off of it. Maybe I'm vastly misunderstanding how e-mail works in general: To receive mail, I should only need port 25, SMTP, open to the internet, correct? Should I be concerned about some authentication failure from the outside to my relay? (My relay requires user/pass to use, my ISP's requires none.)

    Read the article

  • how to tune libstdc++ to the native architecture when building gcc

    - by John D
    I recently found that when I build my C++ software, I get about a 10% speedup by using the g++ march=native option. When compiling gcc and libstc++, is it possible to tune the libstdc++ library to the native architecture as well? I couldn't find any mention of this in the gcc install configuration documentation. (I'm building gcc 4.6.2 on Linux Mint 11 with an Intel Core i7 Sandy Bridge-E processor.)

    Read the article

  • Moving Portable Office. Have a LAN & Phone line query?

    - by John Smith
    We are about to move a portable office that has 8 phones and 12 lan connections. They are all wired back to our main switch and Nortel bcm200 phone system which are only about 20m (65ft) away. After the move the office will be 180m (600ft) away from these. What is the maximum length of cable a digital phone line can be? I am aware that a lan connection can only be 100m (305ft) when using cat5e utp. Does this rule apply to phone connections also? If so how can I extend beyond 100m for the phones? I was going to install about three cabinets, 3 switches and 6 patch panels for the lan connections but the ideal struck me tonight that maybe I could run a fibre optic line. Would this be feasible? Any feedback on this is greatly appreciated. Thanks

    Read the article

  • IIS Express only utilizes 13% of i7 Quad Core

    - by John Nevermore
    Since one of my scripts got incredibly complex, i was benchmarking the performance of moving some javascript processing logic to the server side in my ASP.NET MVC 4 application. According to taskmgr.exe, IIS Express only utilizes 13% of my i7. I decided to throw in 3 parallel tasks calculating the fibonacci sequence up to 50 and the IIS express still wouldn't utilize more than 13% of my cpu. Is there anything i can do, so that the application utilizes the full cpu, as it would in a real server ?

    Read the article

  • How to change Windows admin password from guest user

    - by John Smiith
    How to gain access of admin account of Windows, I activated a guest user and I want to change the admin password from the command line. When I type: net user administrator password the response is System error 5 has occurred. Access is denied I am using winxp pro sp2 I am running this command from cdm.exe and I am running this command from guest user. I actually want to change my admin password from guest user.

    Read the article

  • Samba and Windows 7

    - by John Gaughan
    I built a new computer with the intention of it being primarily a home file server. Here is my setup: one desktop with Windows 7 64 HP one laptop with Windows 7 64 HP one desktop with Kubuntu 11.10 (server) The two desktops use static IPs, and I have hostnames mapped in the HOSTS files on all three systems. I have the same username/password combo on all three systems. I have been trying for a while now to set up Samba so the Windows 7 systems can see and use it. Even if I can get the server to show up, Windows is unable to log in. One of the first things I did was to enable LMv2 authentication, which this version of Samba (3.5.11) supports. The workgroup is set correctly. I can normally see the server, but cannot authenticate. Windows homegroup is turned off. Pinging between machines works fine, and the two Windows 7 systems work together flawlessly. What I am trying to do is set up Samba to use peer to peer networking using NTLM security and user-mode authentication. According to the documentation this is possible, but there are no examples that I could find. In all the googling I have done, I see a lot of people asking how to set this up but it either works for someone else and not for me (no idea what I'm missing), or it doesn't work. Has anyone gotten this to work? Is there a place I could download a smb.conf that is set up to work in this environment?

    Read the article

  • Log and Block Website using Windows 2008 SBS

    - by John
    A client has asked me to setup Windows 2008 SBS to block and log websites from a list they will provide. As far as I know they only have standard edition which means I cannot use ISA. I was thinking of using squid authenticated against Active Directory. There is no budge for additional software. Does any one know of a different/better solution using either open source software or software that is available in Windows 2008 SBS? Thanks

    Read the article

  • check_snmp with snmpv3 protocol giving "Unkown Report message" error

    - by John
    I'm trying to add a nagios command to use snmpv3 for monitoring printer status messages. When using the check_snmp command, I get the following error: External command error: snmpget: Unknown Report message Here is the command I'm typing in: ./check_snmp -P 3 -H <hostname> -L authPriv -U snmpuser -A snmppassword -X snmppassword -o 1.3.6.1.4.1.11.2.4.3.1.2.0 -C public -d "STRING:" -a MD5 These values for auth key, private key, username, etc all work when using snmpwalk. Can someone enlighten me as to what that error message really means? EDIT: It looks like check_snmp isn't taking my v3 credentials when passing over to snmpget. Here is my input with the verbose option: ./check_snmp -H <hostname> -o 1.3.6.1.2.1.2.2.1.10.1 -C public -m ALL -P 3 -L authPriv -U snmpuser -a MD5 -A snmppassword -x DES -X snmppassword -v And here is the output: /usr/bin/snmpget -t 1 -r 5 -m ALL -v 3 [authpriv] <hostname>:161 1.3.6.1.2.1.2.2.1.10.1 External command error: snmpget: Unknown Report message So I guess now my question would be: why isn't check_snmp passing all the commandline options to snmpget?

    Read the article

  • Diagnosing and debugging LAN congestion / connection issues

    - by John Weldon
    What are the top N tools / methodologies used to diagnose and repair network issues? Given a LAN, for example, where users are able to consistently ping an outside server, but any data intensive connections are flaky; how would you begin solving the network issues? I imagine issues like congestion, bandwidth constraints, throughput constraints, etc. are all factors, but I don't know how to diagnose those issues. I'm especially interested in LAN environments (rather than WAN)

    Read the article

  • Mysql Fail to start

    - by John Naegle
    I'm running a Ubuntu 12.04 LTS Virtual Machine. Last week, the VM stopped unexpectedly now mysql will not start on the VM. These two events may be related, they may not be. When I try to connect: $ mysql ERROR 2002 (HY000): Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld.sock' (2) Then: $ sudo service mysql start start: Job failed to start And $ dmesg [ 1838.218400] type=1400 audit(1374633238.253:50): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/mysqld" pid=18473 comm="apparmor_parser" [ 1838.358656] init: mysql main process (18477) terminated with status 1 [ 1838.358695] init: mysql main process ended, respawning [ 1839.269303] init: mysql post-start process (18478) terminated with status 1 And $ service mysql status mysql stop/waiting I think this means mysql is crashing when it starts: $ sudo mysqld start 130723 21:51:24 InnoDB: Assertion failure in thread 3064211200 in file fut0lst.ic line 83 InnoDB: Failing assertion: addr.page == FIL_NULL || addr.boffset >= FIL_PAGE_DATA InnoDB: We intentionally generate a memory trap. InnoDB: Submit a detailed bug report to http://bugs.mysql.com. InnoDB: If you get repeated assertion failures or crashes, even InnoDB: immediately after the mysqld startup, there may be InnoDB: corruption in the InnoDB tablespace. Please refer to InnoDB: http://dev.mysql.com/doc/refman/5.5/en/forcing-innodb-recovery.html InnoDB: about forcing recovery. 02:51:24 UTC - mysqld got signal 6 ; Per the manual, I went to the data directory (/var/lib/mysql) and ran this: myisamchk --silent --force */*.MYI Then: $ sudo mysqld ... InnoDB: Your database may be corrupt or you may have copied the InnoDB InnoDB: tablespace but not the InnoDB log files. See InnoDB: http://dev.mysql.com/doc/refman/5.5/en/forcing-innodb-recovery.html InnoDB: for more information. ... Is my database corrupt? What can I do to recover? Re-install mysql? Something less drastic? I'm fine with losing the database, I just want a working system.

    Read the article

  • What is the best way to clone Win7 machines?

    - by John Hoge
    I'm looking to buy 5 new Win7 boxes and would like to ease deployment by cloning the OS. What I would like to do is install a fresh OS (Dell doesn't seem to sell machines without preinstalled crapware anymore) and then install a few apps on the first one. Once it is just right, I want to clone the OS and install the image on the other four machines and just change the machine name. Is this possible to do without any extra third party software? What I am thinking of doing is backing up the disk image of the first machine to a network share, and then booting the others to the windows install DVD and restoring the same image on each machine. Has anyone had any luck with this technique?

    Read the article

  • Overclock Failed

    - by John
    This morning when I tried to turn on my computer, the monitor would not display anything. The computer is on, but no UI on the monitor and no beep. I turned off the computer and turn it back on again. This time, the computer was on for about 2 seconds and automatically turned itself off for about 2 second and automatically turned itself back on. This happened two times without the monitor displaying any UI. On the third try, the computer did the same thing but when it turned itself back on, the monitor displayed this: American Megatrends Asus P8P67 Le ACPI bios Revision 1011 CPU Intel Core i5 2500K CPU @ 3.30GHz Speed: 3300MHz Total Memory 4096 MB (DDR3-1333) USB Devices Total: 0 Drive, 1 Keyboard, 1 Mouse, 2 Hubs Detected ATA/ATAPI Deivces SATA6G_2 Hitachi HDs821010CLA 332 SATA3G_1 Corsair force 3 SSD SATA3G_2 HL-DT-ST DB-RE UH12CS28 Overclocking Failed! Please enter setup to reconfigure your system. Press F1 to Run Setup. After I pressed F1, it went into the Asus EF1 Bios Utility. I couldn't do anything in there so I just exited. After which, the computer auto turned off and on again and I was able to use the PC like regular. This has never happened to this computer before and the day before, nothing seemed wrong, just regular use and some gaming.

    Read the article

  • Free Hosting control panel

    - by John Maxim
    I'm in the mid of researching for one of the best hosting control panels. The server I run is Ubuntu and I have some experience with ISPConfig 2 & 3. Since I haven't explored any others available, what are the recommended ones for an Ubuntu server? I asked because I find that there seems to be some disabling and modifications required for an Ubuntu server if I need to use ispconfig which causes the server to change its actual way of running. It's quite good though, but any more recommended ones ? Something more organic? which doesn't require much breaking and changing. I'm not asking for the simple one, I don't mind going extra mile to install a powerful one but just try sticking with most Ubuntu's conventions will be an ideal one for me. And of course, if there happens to be something that meets the requirement as mentioned "Ubuntu conventions" and also simple to install at the same time, that'd be a bonus. Thanks in advance.

    Read the article

  • Copy seleted row to another worksheet

    - by ???? ???????
    There are for ex. 10 rows in one worksheet. When user clicks on one row it should be presented on another worksheet. Is it possible? Any help to do it? EDIT: To clarify: In one sheet are presented for example student exam marks on first year: John 10 8 10 7 Nick 8 9 8 9 Maria 7 8 8 7 On 2nd sheet there are student informations on the second year: John 9 9 10 8 Nick 8 8 9 7 Maria 7 6 8 8 I want to have give some kind of final certificate for student so summary information should be presented on the third sheet. I doesn't need to be on click. There could be drop down list on the third sheet.

    Read the article

  • How many times can data be read from a USB flash drive?

    - by John
    While I am aware that performing writes on a USB flash drive degrades the life expectancy of the device. I have heard the quantity of writes is anywhere from 100 thousand to 10 million, but I have not heard about number of read operations. Does reading from the device count toward this total? I am interested in writing only once to a flash drive and setting it to read-only. Then reading files from the device a thousand or more times per day, but am wondering if (at say 1,000 reads per day), the flash drive will need to be replaced within 100 days (assuming a 100,000 r/w cycle lifetime)?

    Read the article

  • regsvr32 fails on Windows Server 2003 - LoadLibaray ("my.dll") failed

    - by John Mo
    The DLL in question is a VB6 web class. When deploying, the old one needs to be unregistered and the new one registered. This has worked for many years but has failed now with the following error in a message box: LoadLibrary("c:...\my.dll") failed - The filename, directory name, or volume label syntax is incorrect. I don't think there's a problem with the DLL being (un)registered because it's failing to unregister the existing DLL that was at one time successfully registered. I don't think there's a filename or path problem. Regsvr32 is executed using a batch file where the full path to the DLL is specified. The path has not changed. The batch file has not changed. The DLL has not changed (at least not the old one I need to unregister). It's a programming problem to me because I need to release an updated DLL, but I'm thinking it's maybe an admin problem best suited to the talents of the serverfault audience. I'm hoping somebody knows about a Windows Update or something that might hose regsvr32. Thank you.

    Read the article

  • measuring microseconds a process runs in Linux

    - by John Kube
    I'm looking to get the number of microseconds that a process takes to execute. Does anybody know how to do this on a Linux system? (I would settle for milliseconds, if that's as good as I can get.) NOTE: I don't think the time command will work to the accuracy I'm looking for...

    Read the article

< Previous Page | 49 50 51 52 53 54 55 56 57 58 59 60  | Next Page >