Search Results

Search found 19768 results on 791 pages for 'hardware programming'.

Page 535/791 | < Previous Page | 531 532 533 534 535 536 537 538 539 540 541 542  | Next Page >

• Why Standards Place Limits on Data Transfer Rates?

  - by Mehrdad

  This is a rather general question about hardware and standards in general: Why do they place limits on data transfer rates, and disallow manufacturers from exceeding those rates? (E.g. 100 Mbit/s for Wireless G, 150 Mbit/s for Wireless N, ...) Why not allow for some sort of handshake protocol, whereby the devices being connected agree upon the maximum throughput that they each support, and use that value instead? Why does there have to be a hard-coded limit, which would require a new standard for every single improvement to a data rate?

  Read the article

• Difference between tc qdisc and netdev_max_backlog

  - by Mediocre Gopher

  I'm wondering what the difference between these two things on linux is. According to the docs tc qdisc can be used to set the queue size for egress and ingress packets coming in and out of the NIC (or that's how I understood it). But from what I understand netdev_max_backlog can also be used to set this. If I were to set both of them which would be used? Or are there actually two queues that are being manipulated in this case? If there are two queues, which queue is above the other (if the application is at the top and the hardware at the bottom)?

  Read the article

• Mongodump on Gridfs is killing the host IOs

  - by Raphael

  I'm trying to make a mongodump from our production mongodb while the production is running. We have three production instances, one regular mongodb, one with very few gb of data on gridfs, one with a larger amount of data on gridfs. All mongodb instances are running in version 2.4.9 on a ubuntu 10.04 virtual server. I use a mongodump command to export the bases to another server. Unfortunately our machines are virtually hosted in a "low performances" datacenter (vmware based) so when I try to export the large gridfs db, the disk IO hits 100% (and 50% of the cpu starts waiting for IO too). This has a very negative impact on the production applicatiosn because db access time is excessively increased, making the applications unusable. I'm looking for a way to regulate the mongodump so the export goes slower but cooler on the hardware ressources allowing better performances for the applications to run. Has anyone had a similar scenario ?

  Read the article

• How to make phone calls using a pc, modem, headphone and no actual phone instrument

  - by user18151

  Hi, I have a phone landline connection and I DO NOT have a phone instrument. I connect the cable into my laptop, and want to make calls using my laptop. I have an HDA CX20561 modem. I seem to be able to dial number using dialer.exe, though nothing seems to happen. From Microsoft kb http://support.microsoft.com/kb/958143, it looks like dialer.exe alone is not enough for the call. Can somebody tell me how to make and receive phone call with whatever hardware I have, i.e. what software will I need. Thanks.

  Read the article

• ATI Radeon HD 5970 Display numbering issues

  - by Arindam Sen

  I have 2 computers on which i have ATI Radeon HD 5970 graphics card installed. There is 1 VGA out and 1 DVI out in it. When I connect my VGA out to a monitor on my 1st computer, it shows it as display 1 and when I connect my DVI out to a monitor it show it as display 2 (I am using extended display). When I do the same thing on my 2nd computer it shows just the opposite. The VGA out shows as display 2 and the DVI out shows as display 1. Is it a problem with the drivers or the hardware? (because the graphics card on both is exactly the same)

  Read the article

• Single device that can work as tablet and as desktop PC

  - by flow

  I have a macbook pro and an iPad 2. I tried to use iPad 2 for work when I am out of the office but this is not very comfortable since one has to sync documents, not all Os X Lion apps exist for iPad 2 and so on. I think a solution would be a single tablet device that at the office can be connected to some dock station and then I have the equivalent of my macbook, but when I am out of the office I can touch the screen and used the same applications while on the road. As far as I know the iPad 2 does not and will not allow this. Therefore I wonder if you could recommend me another hardware/tablet/etc that could work this way now as of March 2012.

  Read the article

• Recursive Batch File

  - by MCZ

  I have a file that looks this: head1,head2,head3,head4,head5,head6 a11,a12,keyA,a14,a15,a16 a21,a22,keyB,a24,a25 a31,a32,keyC,a34 a41,a42,keyB,a44,a44 a51,a52,keyA,a54,a55,a56 a61,a62,keyA,a64,a65,a66 a71,a72,keyC,a74 some message Objective: Write list of unique keys to a text file. For example, the result for the file described above should be: keyA, keyB, keyC Here's the pseudocode I would like to implement in batch file recur.bat Read second line of inputfile If no key exist on second line, return else continue Append keyX to list FINDSTR /v keyX inputfile Pipe results to recur.bat I don't know if this is the most efficient way to do this without using actual programming language. Any suggestions for actual batch file code?

  Read the article

• XP Mode under Win 7 Professional: Windows Activation Update failure despite activated Windows

  - by Cristina

  I am trying to install Windows XP Mode from here: http://www.microsoft.com/windows/virtual-pc/download.aspx (the Hardware-Assisted Virtualization Detection Tool has given me the green for proceeding) Even though my Windows has been activated a year or so ago, the download button leads me to a splash screen saying "Windows validation required". I am next forced to download a WindowsActivationUpdate.exe which, after downloading some mysterious "update", fails with the error message "Update installation failed, error information 0x80070002" (rough translation from German). I've tried running it both normally and as Administrator. What could be the problem?

  Read the article

• mirroring linux server to external usb harddrive

  - by DuPie

  My google-fu must be sucking. i havent been able to find a good solution for the following: numerous Linux server on commodity hardware Trying to do a recovery mirror copy to external harddrives External harddrives are smaller than source harddrives, but larger than data External drives are connected via usb2 (slow) Servers range from 20GB of data to 400GB of data Servers are remote, so hands on access is a pain need to copy boot files. empty external drives currently Basicly, looking for a way to do use a ghosting solution from INSIDE a running linux server to an external harddrive, without booting a cd etc. the rsync/cpio solutions i've looked at dont work great with grub/dev/proc etc. I understand that since the system isnt offline, it wont be a "mirror" image as files change, but thats ok. Are there any free/commercial products that would work?

  Read the article

• Cannot assign port 4 to WAN on TP-Link WR740N by DD-WRT wiki

  - by Victor Sergienko

  I'm following the DD-WRT instruction to get TP-Link WR740N v3's Port 4 on a different VLAN, but this doesn't happen. First, I have no "Setup VLANs" settinngs tab in DD-WRT v24-sp2 (07/20/12) std r19519. I can get Internet on Wi-Fi if assigning eth1 to "WAN Port", but then all Ethernet ports get on the same VLAN and any wired connection grabs the DHCP address and Internet connection from router. When following the "old" instruction, if I run, say, nvram set vlan2ports="2 5*", should there appear a new interface, vlan2, in ifconfig, after ifconfig vlan2 up? It doesn't - does it mean there is no support for different VLANs in my software/hardware? What am I missing? Is it impossible to create more VLANs on TP-Link740?

  Read the article

• Win 7: Share internet connection via Ethernet and WiFi

  - by Anvaka

  I have the following configuration: Box 1. Running Win 7, connected to the internet via Eth0. Has one wireless network adapter and one more ethernet adapter (say, Eth1). Box 2. Running Win XP, has one ethernet adapter. I'd like to share Internet connection of the Box 1 with Box 2 via cable and have box 1 also sharing the Internet with other wireless devices. I don't want to buy any additional hardware. Is it possible? PS: Sorry if I'm unclear. I merely know nothing about NAT and network administration

  Read the article

• Win 7: Share internet connection via Ethernet and WiFi

  - by Anvaka

  I have the following configuration: Box 1. Running Win 7, connected to the Internet via Eth0. Has one wireless network adapter and one another ethernet adapter (say, Eth1). Box 2. Running Win XP, has one ethernet adapter. I'd like to share Internet connection of the Box 1 with Box 2 via cable and have box 1 also sharing the Internet with other wireless devices. I don't want to buy any additional hardware. Is it possible? PS: Sorry if I'm unclear. I merely know nothing about NAT and network administration.

  Read the article

• Speeding up Connection Between Computer and Wireless/Bridged Router

  - by Justian Meyer

  Hey everyone, I looked through other questions, but didn't find useful responses. Our main computer has a dl speed of 6 Mbps, but some of our other computers are getting only 40-200 Kb! The router is wireless, but all computers are connected using a Netgear Wall-Plugged Bridge XE102, which transmits information via the building's powerline. It can't be the hardware itself, however, because some computers still manage decent speeds. The computers afflicted are running on Microsoft XP Service Packs 2 and 3, but so are computers that are totally functional. These speeds severely impede on productivity and are excruciatingly frustrating when trying to cram in time in the early hours. Could it be an issue with the computer? Location? Router? Many thanks in advance, Justian

  Read the article

• Routing Essentials

  - by zharvey

  I'm a programmer trying to fill a big hole in my understanding of networking basics. I've been reading a good book (Networking Bible by Sosinki) but I have been finding that there is a lot of "assumed" information contained, where terms/concepts are thrown at the reader without a proper introduction to them. I understand that a "route" is a path through a network. But I am struggling with visualizing some routing-based concepts. Namely: How do routes actually manifest themselves in the hardware? Are they just a list of IP addresses that get computed at the network layer, and then executed by the transport? What kind of data exists in a so-caleld routing table? Is a routing-table just the mechanism for holding these lists of IP address (read above)? What are the performance pros/cons for having a static route, as opposed to a dynamic route?

  Read the article

• Which one is better deal: iPed or Apple iPad?

  - by Evan Carroll

  The Chinese knockoff iPed is now in the wild and receiving a lot of attention? Does anyone know how the Android distribution it ships with compares with Apple iPad's software pack? How does the look-and-feel of the iPed fit with the Apple iPad? Quite frankly, I have little interest in Apple products because of the company policy. But, cheaper comparable hardware running open-source software is pretty interesting... Anything useful to add.. Here are the Apple iPad specs for comparison. The iPed is priced at $199.00, the Apple iPad starts at $499.00 .

  Read the article

• How can I to take an HDMI TV broadcast and overlay text in real time?

  - by ObligatoryMoniker

  Our company wants to be able to have LCD TVs displaying TV with the ability to add an overlay, like a stock ticker at the bottom of the screen, where human resources can add content to be displayed. I have been trying to nail down the correct terminology for this and come across terms like Keying, Compositing, Live Broadcast Graphics Presentation, and Hardware Overlay but I don't know which of these terms is truly the correct way to refer to what I am trying to do. Black Magic offers a product that seems like it can do what I am looking for but their product seems like it is geared for a totally different purpose than what I would be using it for. Compix also seems to have a product that would do what I need but again it seems like killing a fly with a sledge hammer. How can I to take an HDMI TV broadcast and overlay arbitrary content in real time?

  Read the article

• Should I quit using Ifconfig?

  - by Zhen

  With the servers that mount Infiniband cards, when I use the ifconfig command I have the warning: Ifconfig uses the ioctl access method to get the full address information, which limits hardware addresses to 8 bytes. Because Infiniband address has 20 bytes, only the first 8 bytes are displayed correctly. Ifconfig is obsolete! For replacement check ip. Should I quit using ifconfig? It is deprecated in favor of ip command? Or it will be update in the near future.

  Read the article

• For Loop counting from 1 to n in a windows bat script

  - by raoulsson

  I need to run a windows command n times within a bat script file. I know how to do this in various programming languages but cannot manage to get it right on the windows command line :-( I would expect something like either for(int i = 0; i < 100; i++) { // do something } or even this (though not entirely seriously) 1.upto(100, { // do something }) Thanks! EDIT I can write a program in java, perl, c or whatever that will generate a bat script that looks like this for %%N in (1 2 3 4 5 6 7 8 9 10 11 12) do echo %%N and so on. Or even "better": echo 1 echo 2 echo 3 echo 4 echo 5 echo 6 echo 7 echo 8 echo 9 echo 10 echo 11 echo 12 and then execute it... But the thing is that I need a concise way to specify a range of numbers to iterate through within the script. Thanks!

  Read the article

• What would you use to keep track of all the random information about your LAN/Enviroment?

  - by agnul

  Say you work in your average anarchy... no appointed IT guy, no Office-Manager whatsoever, just developers working in free-for-all mode and a couple of non technical people around for admin (non IT) stuff. What would you use to keep track of Hardware / Software inventory Backups of OS images, Drivers, and all that LAN configuration information Passwords for all the systems Currently I'm thinking of having some sort of wiki + web server on our only ''server-class'' machine, but then I fear I'd be the only one who would go through the hassle of adding information in the wiki... So, have you been through that? What would you suggest?

  Read the article

• Large file copy from NFS to local disk performance drop

  - by Bernhard

  I'm trying to copy a 200GB file from an NFS mount to a local disk. The local disk is an XFS filesystem on a LVM on top of a RAID 5 system (hardware RAID controler). I'm using rsync to monitor the transfer speed. At the beginning the IO speed is about 200MB/s, stable for the first 18GB. But then the performance drops by a factor of 10-20 and never recovers to the initial rate. Sometimes it reaches about 50-100MB/s but just for a few seconds and then the process seems to hang for a bit. At the same time all file-stat operations on the target filesystem are blocking for a long time (minutes). Also interrupting the copy process blocks for several minutes, a sub-sequent delete of the partly copied file takes also several minutes. Any ideas what could be causing this?

  Read the article

• Internet Explorer 8/9 javascript disable, need to enable back

  - by Shiro

  Dear all, This is not a programming issue, just want to ask any one having Internet Explorer Javascript disabled issue. I try go to Internet Option enable everything, including javascript restart it. But all the javascript still disabled. I go to jQuery API website, test the javascript, at the Demo part nothing show. Even I write a alert("hello"); in a html file, nothing come out. I am not sure what happen to my Internet Explorer. Initially I am using IE8, I try to update to IE9Beta, IE9RC, the problem start from IE8-IE9RC still haven't resolved. I am not sure what application crash with the IE. Please advice! It is Urgent. Thanks!

  Read the article

• Having Troubles Getting My Apache Server Online(NodeJS and Apache)

  - by Jeff Armingol

  I am new here. This is my situation. I am using nodejs modules, serialport2 and socket.io, because I am trying to forward the data from my arduino hardware through serialports. In my server side script, I read the data then forward it to the client side. Now I am using Apache to serve the html page,which is the client side. I am running Nodejs on port 8000 and Apache on port 80. It is running OKAY when I view it in my browser typing localhost:80. The data is appearing and seems fine. Now when I tried to get my Apache server online using a Free DDNS provider(http://www.noip.com/) and my port80, it loaded the webpage but there are no data appearing on the page. What seems to be the problem here? Really need your expertise and advice. Thanks in advanced!

  Read the article

• Will disabling NAT on my wireless router cause a performance hit on my DSL router?

  - by user117313

  I have a Thomson TG508v2 router/modem and a brand new AirPort Extreme connected to it. At first, I set the AirPort Extreme to "share a public IP", which enables DHCP/NAT. Everything works great but I was having the Double NAT error. So I set the AirPort Extreme as bridge mode, which disables DHCP/NAT and let my crappy modem handle my internal network IPs. Will this cause any performance hit in my network? I'm worried because I'll outsource this job from AirPort Extreme (premium hardware) to the crappy modem. Before you suggest, I tried setting my modem as a bridge and configuring PPPoE on the AirPort Extreme, however it wouldn't connect to the internet, so I just dismissed leaving the modem as bridge.

  Read the article

• Which Power supply I should buy

  - by arayman

  I am going to buy a new PSU of CORSAIR for my IBM thinkcentre desktop. My previous original PSU was of 230 watts. I have not added any hardware in the CPU. It's in same condition as it was when I bought. On that basis, please suggest which power supply of Corsair and of how many watts will be suitable for me to buy, after referring to the under given weblink. http://www.corsair.com/en/power-supply-units.html Thanks.

  Read the article

• How to solve my black screen at boot?

  - by Juanillo

  I've got a friend with a weird problem. When he starts his computer the screen is completely black until the computer is completely started. So the screen is black until it suddenly shows the Windows desktop. He said that this is happening since a technical service repaired his computer, but that repair is not now in warranty. Recently the computer stopped working, but as the screen is black he cannot access to BIOS or start in safe mode (by pressing F8). When he inserts the Windows Vista DVD the system doesn't boot from DVD (it mustn't be configured in this way in the BIOS). Maybe there´s a problem with the hardware (maybe the graphic card)? Can anyone explain a reason why the screen is black during start-up? Any idea of what to do with the computer to restore it?

  Read the article

< Previous Page | 531 532 533 534 535 536 537 538 539 540 541 542  | Next Page >