common dialog - Page 537

Slow draw on some apps and dynamic clocks not working properly with ATI/AMD proprietary drivers

- by Rakeka

I've recently purchased a new computer (around July 2010) and I've been having some problems with proprietary video drivers on Linux. The hardware is: Video: ATI/AMD Radeon HD 5870 (XFX HD-587X-ZNFC); Motherboard: Asus P7P55D-E Deluxe; Processor: Intel i5 750; Memory: Kingston Hyperx KHX1600C8D3K2/4GX (2x - 8GB Total); Power Supply: XFX P1-750B-CAG9; There are no overclocks, not even the memories (they are at 1333mhz due processor memory controller limitation). The operational system is a homebrew Linux distribution with the following software: Architecture: x86_64 (multilib) Kernel: 2.6.35.10 Xorg: 7.5 Window Manager: wmii-3.9.2 Video Driver: ATI/AMD Catalyst 10.12 There are no desktop effects programs like compiz fusion or beryl. The problems: With ATI/AMD proprietary driver, some applications are with slow draw/redraw, and, the same applications make the driver to increase the card clocks to maximum (0% gpu activity, only the clocks are increased). I dunno exactly how to describe the slow draw but I'll list some applications and symptoms. xterm Flickers a lot when drawing continuous output; When I'm in a workspace with fullscreen xterm, The gpu load stays at 12% in idle, and, with smaller xterm, smaller GPU load. "aticonfig --odgc" output: Default Adapter - ATI Radeon HD 5800 Series Core (MHz) Memory (MHz) Current Clocks : 157 300 Current Peak : 850 1200 Configurable Peak Range : [600-900] [900-1300] GPU load : 12% "aticonfig --pplib-cmd 'get activity'" output: Current Activity is Core Clock: 157MHZ Memory Clock: 300MHZ VDDC: 950 Activity: 12 percent Performance Level: 0 Bus Speed: 5000 Bus Lanes: 16 Maximum Bus Lanes: 16 More examples: mplayer time info flickers on terminal; "find /" flickers a lot (It takes some time to stop with control-c. But, If I change the workspace or put some window upon it, just after the control-c, it stops instantly); "cat somefile" if the file is big (Xorg.0.log for example) it takes some time to display; vim and less (ex: find / | less) don't have much problems, just a little flicker when scrolling; mplayer (no gui) Slow reproduction and seek with -vo x11; Tearing with -vo xv; Time info flickers on terminal (xterm consequence); gvim A little slow draw when scrolling with page up/page down; Firefox Slow draw/redraw on some pages like www.boadica.com.br and sometimes on www.youtube.com with flash enable (never noticed on many pages); Corruptions when informative yellow boxes are showing and scroll the page (an gray box appears at the same place of the informative box); "Wallpaper" After minimizing a fullscreen window or changing to an empty workspace it takes some time to redraw wallpaper. "Video Card" The core and memory clocks are increased with the events described above and on other situations like change workspace (even without wallpaper), minimize, maximize or move a window; Idle clocks: Core: 157mhz, Memory: 300mhz Full clocks: Core: 850mhz, Memory: 1200mhz xpdf Painful slow scrolling; display (from ImageMagick) Slow menus and sometimes slow image redraw; Programs that I use and are apparently without problems: gimp; pidgin; mplayer (-vo gl, gl2); blender; unigine heaven (better fps than on Windows); doom3; tibia; penumbra overture; amnesia the dark descent (wine); diablo 2 (wine); No problems on Windows (Windows 7 Ultimate 64bit). And special note to this: Full desktop effects from Debian and Ubuntu gnome appearance cpanel don't cause ANY problems, even the core and memory clocks don't increase when change workspace, minimize, maximize or move a window. What I've tested: Unsuccessful tests: Tested all drivers versions since 10.6 (released approximately when I've installed the first slackware in this PC); Tested other video card - ATI/AMD Radeon HD 5570 (XFX HD-557X-ZHF2); Tested some options on xorg.conf and that I've found googling (some of these options are commented on my xorg.conf. I'll send the links at the end of post); Tested some patches like 107_fedora_dont_fill_bg_none.patch and xserver-xorg-backclear.patch from Arch Linux Catalyst page (https://wiki.archlinux.org/index.php/ATI_Catalyst); Tested other distros and software versions: Tested XORG-7.6 on my own distribution; Tested Debian Squeeze (testing - from 2010-12-20); Tested Ubuntu Marverick (10.10); Tested Slackware 13.1; Distros info: Architecture: i386 Debian and Ubuntu with all default software (kernel, gnome, xorg, drivers); Slackware with Catalyst from AMD page and default window managers like: fvwm, xfce, and my own build of wmii; Successful tests: Tested other video card (only on my homebrew distro) - NVIDIA Geforce 7300GS with driver 260.19.29; That didn't shown the slow draw problems, but that card is a bit obsolete, so, dunno if that lacks features like the dynamic clocks. I don't dispose of other video cards like nvidia g/gt/gts/gtx 200~400~500 or Radeon HD 3000/4000/6000 to make more tests. Tested other hardware: Video: ATI/AMD Radeon HD 5570 (XFX HD-557X-ZHF2); Motherboard: Intel DG31PR; Processor: Core 2 Duo E6750; Software for that hardware: Fresh install of same distros (except for the mine) with same program versions; That video card (HD 5570) were full time at the maximum clocks (something like 500/750, don't remember) in all the operational systems (Windows XP and Windows 7 too), but it didn't shown the same problems that I have here. I've googled a lot about common problems with ATI/AMD proprietary drivers for Linux and didn't find similar problems, except by the Firefox corruptions, that the solutions were to disable ATI Direct2DAccel and use XAA. With XAA the problems persists and the other applications like pidgin and rest of Firefox showed the same problems of slow draw/redraw. Open source Drivers: With open source drivers (xf86-video-ati-6.13.2) I hadn't the same slow draw problems, but, had other problems, that, for now, make it no viable solution. I'll not discuss it here because this is another line of problems and will confuse everything. If it happens to be the only solution, I'll make another thread to discuss it. Logs and Configs: kernel .config dmesg xorg package list xorg.conf Xorg.0.log

Read the article

PASS: Bylaw Change 2013

- by Bill Graziano

PASS launched a Global Growth Initiative in the Summer of 2011 with the appointment of three international Board advisors. Since then we’ve thought and talked extensively about how we make PASS more relevant to our members outside the US and Canada. We’ve collected much of that discussion in our Global Growth site. You can find vision documents, plans, governance proposals, feedback sites, and transcripts of Twitter chats and town hall meetings. We also address these plans at the Board Q&A during the 2012 Summit. One of the biggest changes coming out of this process is around how we elect Board members. And that requires a change to the bylaws. We published the proposed bylaw changes as a red-lined document so you can clearly see the changes. Our goal in these bylaw changes was to address the changes required by the global growth initiatives, conduct a legal review of the document and address other minor issues in the document. There are numerous small wording changes throughout the document. For example, we replaced every reference of “The Corporation” with the word “PASS” so it now reads “PASS is organized…”. Board Composition The biggest change in these bylaw changes is how the Board is composed and elected. This discussion starts in section VI.2. This section now says that some elected directors will come from geographic regions. I think this is the best way to make sure we give all of our members a voice in the leadership of the organization. The key parts of this section are: The remaining Directors (i.e. the non-Officer Directors and non-Vendor Appointed Directors) shall be elected by the voting membership (“Elected Directors”). Elected Directors shall include representatives of defined PASS regions (“Regions”) as set forth below (“Regional Directors”) and at minimum one (1) additional Director-at-Large whose selection is not limited by region. Regional Directors shall include, but are not limited to, two (2) seats for the Region covering Canada and the United States of America. Additional Regions for the purpose of electing additional Regional Directors and additional Director-at-Large seats for the purpose of expanding the Board shall be defined by a majority vote of the current Board of Directors and must be established prior to the public call for nominations in the general election. Previously defined Regions and seats approved by the Board of Directors shall remain in effect and can only be modified by a 2/3 majority vote by the then current Board of Directors. Currently PASS has six At-Large Directors elected by the members. These changes allow for a Regional Director position that is elected by the members but must come from a particular region. It also stipulates that there must always be at least one Director-at-Large who can come from any region. We also understand that PASS is currently a very US-centric organization. Our Summit is held in America, roughly half our chapters are in the US and Canada and most of the Board members over the last ten years have come from America. We wanted to reflect that by making sure that our US and Canadian volunteers would continue to play a significant role by ensuring that two Regional seats are reserved specifically for Canada and the US. Other than that, the bylaws don’t create any specific regional seats. These rules allow us to create Regional Director seats but don’t require it. We haven’t fully discussed what the criteria will be in order for a region to have a seat designated for it or how many regions there will be. In our discussions we’ve broadly discussed regions for United States and Canada Europe, Middle East, and Africa (EMEA) Australia, New Zealand and Asia (also known as Asia Pacific or APAC) Mexico, South America, and Central America (LATAM) As you can see, our thinking is that there will be a few large regions. I’ve also considered a non-North America region that we can gradually split into the regions above as our membership grows in those areas. The regions will be defined by a policy document that will be published prior to the elections. I’m hoping that over the next year we can begin to publish more of what we do as Board-approved policy documents. While the bylaws only require a single non-region specific At-large Director, I would expect we would always have two. That way we can have one in each election. I think it’s important that we always have one seat open that anyone who is eligible to run for the Board can contest. The Board is required to have any regions defined prior to the start of the election process. Board Elections – Regional Seats We spent a lot of time discussing how the elections would work for these Regional Director seats. Ultimately we decided that the simplest solution is that every PASS member should vote for every open seat. Section VIII.3 reads: Candidates who are eligible (i.e. eligible to serve in such capacity subject to the criteria set forth herein or adopted by the Board of Directors) shall be designated to fill open Board seats in the following order of priority on the basis of total votes received: (i) full term Regional Director seats, (ii) full term Director-at-Large seats, (iii) not full term (vacated) Regional Director seats, (iv) not full term (vacated) Director-at-Large seats. For the purposes of clarity, because of eligibility requirements, it is contemplated that the candidates designated to the open Board seats may not receive more votes than certain other candidates who are not selected to the Board. We debated whether to have multiple ballots or one single ballot. Multiple ballot elections get complicated quickly. Let’s say we have a ballot for US/Canada and one for Region 2. After that we’d need a mechanism to merge those two together and come up with the winner of the at-large seat or have another election for the at-large position. We think the best way to do this is a single ballot and putting the highest vote getters into the most restrictive seats. Let’s look at an example: There are seats open for Region 1, Region 2 and at-large. The election results are as follows: Candidate A (eligible for Region 1) – 550 votes Candidate B (eligible for Region 1) – 525 votes Candidate C (eligible for Region 1) – 475 votes Candidate D (eligible for Region 2) – 125 votes Candidate E (eligible for Region 2) – 75 votes In this case, Candidate A is the winner for Region 1 and is assigned that seat. Candidate D is the winner for Region 2 and is assigned that seat. The at-large seat is filled by the high remaining vote getter which is Candidate B. The key point to understand is that we may have a situation where a person with a lower vote total is elected to a regional seat and a person with a higher vote total is excluded. This will be true whether we had multiple ballots or a single ballot. Board Elections – Vacant Seats The other change to the election process is for vacant Board seats. The actual changes are sprinkled throughout the document. Previously we didn’t have a mechanism that allowed for an election of a Board seat that we knew would be vacant in the future. The most common case is when a Board members moves to an Officer role in the middle of their term. One of the key changes is to allow the number of votes members have to match the number of open seats. This allows each voter to express their preference on all open seats. This only applies when we know about the opening prior to the call for nominations. This all means that if there’s a seat will be open at the start of the next Board term, and we know about it prior to the call for nominations, we can include that seat in the elections. Ultimately, the aim is to have PASS members decide who sits on the Board in as many situations as possible. We discussed the option of changing the bylaws to just take next highest vote-getter in all other cases. I think that’s wrong for the following reasons: All voters aren’t able to express an opinion on all candidates. If there are five people running for three seats, you can only vote for three. You have no way to express your preference between #4 and #5. Different candidates may have different information about the number of seats available. A person may learn that a Board member plans to resign at the end of the year prior to that information being made public. They may understand that the top four vote getters will end up on the Board while the rest of the members believe there are only three openings. This may affect someone’s decision to run. I don’t think this creates a transparent, fair election. Board members may use their knowledge of the election results to decide whether to remain on the Board or not. Admittedly this one is unlikely but I don’t want to create a situation where this accusation can be leveled. I think the majority of vacancies in the future will be handled through elections. The bylaw section quoted above also indicates that partial term vacancies will be filled after the full term seats are filled. Removing Directors Section VI.7 on removing directors has always had a clause that allowed members to remove an elected director. We also had a clause that allowed appointed directors to be removed. We added a clause that allows the Board to remove for cause any director with a 2/3 majority vote. The updated text reads: Any Director may be removed for cause by a 2/3 majority vote of the Board of Directors whenever in its judgment the best interests of PASS would be served thereby. Notwithstanding the foregoing, the authority of any Director to act as in an official capacity as a Director or Officer of PASS may be suspended by the Board of Directors for cause. Cause for suspension or removal of a Director shall include but not be limited to failure to meet any Board-approved performance expectations or the presence of a reason for suspension or dismissal as listed in Addendum B of these Bylaws. The first paragraph is updated and the second and third are unchanged (except cleaning up language). If you scroll down and look at Addendum B of these bylaws you find the following: Cause for suspension or dismissal of a member of the Board of Directors may include: Inability to attend Board meetings on a regular basis. Inability or unwillingness to act in a capacity designated by the Board of Directors. Failure to fulfill the responsibilities of the office. Inability to represent the Region elected to represent Failure to act in a manner consistent with PASS's Bylaws and/or policies. Misrepresentation of responsibility and/or authority. Misrepresentation of PASS. Unresolved conflict of interests with Board responsibilities. Breach of confidentiality. The bold line about your inability to represent your region is what we added to the bylaws in this revision. We also added a clause to section VII.3 allowing the Board to remove an officer. That clause is much less restrictive. It doesn’t require cause and only requires a simple majority. The Board of Directors may remove any Officer whenever in their judgment the best interests of PASS shall be served by such removal. Other There are numerous other small changes throughout the document. Proxy voting. The laws around how members and Board members proxy votes are specific in Illinois law. PASS is an Illinois corporation and is subject to Illinois laws. We changed section IV.5 to come into compliance with those laws. Specifically this says you can only vote through a proxy if you have a written proxy through your authorized attorney. English language proficiency. As we increase our global footprint we come across more members that aren’t native English speakers. The business of PASS is conducted in English and it’s important that our Board members speak English. If we get big enough to afford translators, we may be able to relax this but right now we need English language skills for effective Board members. Committees. The language around committees in section IX is old and dated. Our lawyers advised us to clean it up. This section specifically applies to any committees that the Board may form outside of portfolios. We removed the term limits, quorum and vacancies clause. We don’t currently have any committees that this would apply to. The Nominating Committee is covered elsewhere in the bylaws. Electronic Votes. The change allows the Board to vote via email but the results must be unanimous. This is to conform with Illinois state law. Immediate Past President. There was no mechanism to fill the IPP role if an outgoing President chose not to participate. We changed section VII.8 to allow the Board to invite any previous President to fill the role by majority vote. Nominations Committee. We’ve opened the language to allow for the transparent election of the Nominations Committee as outlined by the 2011 Election Review Committee. Revocation of Charters. The language surrounding the revocation of charters for local groups was flagged by the lawyers. We have allowed for the local user group to make all necessary payment before considering returning of items to PASS if required. Bylaw notification. We’ve spent countless meetings working on these bylaws with the intent to not open them again any time in the near future. Should the bylaws be opened again, we have included a clause ensuring that the PASS membership is involved. I’m proud that the Board has remained committed to transparency and accountability to members. This clause will require that same level of commitment in the future even when all the current Board members have rolled off. I think that covers everything. I’d encourage you to look through the red-line document and see the changes. It’s helpful to look at the language that’s being removed and the language that’s being added. I’m happy to answer any questions here or you can email them to [email protected].

Read the article

Responsive Design for your ADF Faces Web Applications

- by Shay Shmeltzer

Responsive web applications are a common pattern for designing web pages that adjust their UI based on the device that access them. With the increase in the number of ADF applications that are being accessed from mobile phones and tablet we are getting more and more questions around this topic. Steven Davelaar wrote a comprehensive article covering key concepts in this area that you can find here. The article focuses on what I would refer to as server adaptive application, where the server adapts the UI it generates based on the device that is accessing the server. However there is one more technique that is not covered in that article and can be used with Oracle ADF - it is CSS manipulation on the client that can achieve responsive design. I'll cover this technique in this blog entry. The main advantage of this technique is that the UI manipulation does not require the server to send over a new UI when a change is needed. This for example allows your page to change immediately when you change the orientation of your device. (By the way this example was developed for one of the seminars in the upcoming Oracle ADF OTN Virtual Developer Day). In the demo that you'll see below you'll see a single page that changes the way it is displayed based on the orientation of the device. Here is the page with the tablet in landscape and portrait: To achieve this I'm using a CSS media query in my page template that changes the display property of a couple of style classes that are used in my page. The media query has this format: @media screen and (max-width:700px) { .narrow { display: inline; } .wide { display: none; } .adjustFont { font-size: small; } .icon-home { font-size: 24px; } } This changes the properties of the same styleClasses that are defined in my application's skin. Here is a quick demo video that shows you the full application and explains how it works. For those looking to replicate this, here are the basic files: skin1.css @charset "UTF-8";/**ADFFaces_Skin_File / DO NOT REMOVE**/@namespace af "http://xmlns.oracle.com/adf/faces/rich";@namespace dvt "http://xmlns.oracle.com/dss/adf/faces";.wide { display: inline;}.narrow { display: none;}.adjustFont { font-size: large;}.icon-home { font-family: 'UIShellUGH'; -webkit-font-smoothing: antialiased; font-size: 36px; color: #ffa000;} pageTemplate: <?xml version='1.0' encoding='UTF-8'?><af:pageTemplateDef xmlns:af="http://xmlns.oracle.com/adf/faces/rich" var="attrs" definition="private" xmlns:afc="http://xmlns.oracle.com/adf/faces/rich/component"> <af:xmlContent> <afc:component> <afc:description>A template that will work on phones and desktop</afc:description> <afc:display-name>ResponsiveTemplate</afc:display-name> <afc:facet> <afc:facet-name>main</afc:facet-name> </afc:facet> </afc:component> </af:xmlContent> <meta name="viewport" content="width=device-width, initial-scale=1"/> <af:resource type="css">@media screen and (max-width:700px) { .narrow { display: inline; } .wide { display: none; } .adjustFont { font-size: small; } .icon-home { font-size: 24px; } }@font-face { font-family: 'UIShellUGH'; src: url(data:application/x-font-woff;charset=utf-8;base64,d09GRk9UVE8AA..removed code here...AzV6b1g==)format('truetype'); font-weight: normal; font-style: normal; } </af:resource> <af:panelGroupLayout id="pt_pgl4" layout="vertical" styleClass="sizeStyle"> <af:panelGridLayout id="pt_pgl1"> <af:gridRow marginTop="5px" height="40px" id="pt_gr1"> <af:gridCell marginStart="5px" width="100%" marginEnd="5px" id="pt_gc1"> <af:panelGroupLayout id="pt_pgl3" halign="center" layout="horizontal"> <af:outputText value="h" id="ot2" styleClass="icon-home"/> <af:outputText value="HR System" id="ot3" styleClass="adjustFont"/> </af:panelGroupLayout> </af:gridCell> </af:gridRow> <af:gridRow marginTop="5px" height="auto" id="pt_gr2"> <af:gridCell marginStart="5px" width="100%" marginEnd="5px" id="pt_gc2" halign="stretch"> <af:panelGroupLayout id="pt_pgl2" layout="scroll"> <af:facetRef facetName="main"/> </af:panelGroupLayout> </af:gridCell> </af:gridRow> <af:gridRow marginTop="5px" height="20px" marginBottom="5px" id="pt_gr3"> <af:gridCell marginStart="5px" width="100%" marginEnd="5px" id="pt_gc3"> <af:panelGroupLayout id="pt_pgl5" layout="vertical" halign="center"> <af:separator id="pt_s1"/> <af:outputText value="Copyright Oracle Corp. 2013" id="pt_ot1" styleClass="adjustFont"/> </af:panelGroupLayout> </af:gridCell> </af:gridRow> </af:panelGridLayout> </af:panelGroupLayout></af:pageTemplateDef> Example from the page: <af:gridRow id="gr3"> <af:gridCell id="gc7" columnSpan="2"> <af:panelGroupLayout id="pgl8" styleClass="narrow"> <af:link text="Menu" id="l1"> <af:showPopupBehavior triggerType="action" popupId="p1" align="afterEnd"/> </af:link> </af:panelGroupLayout> <af:panelGroupLayout id="pgl7" styleClass="wide"> <af:navigationPane id="np1" hint="buttons"> <af:commandNavigationItem text="Departments" id="cni1"/> <af:commandNavigationItem text="Employees" id="cni2"/> <af:commandNavigationItem text="Salaries" id="cni3"/> <af:commandNavigationItem text="Jobs" id="cni4"/> <af:commandNavigationItem text="Services" id="cni5"/> <af:commandNavigationItem text="Support" id="cni6"/> <af:commandNavigationItem text="Help" id="cni7"/> </af:navigationPane> </af:panelGroupLayout> </af:gridCell> </af:gridRow>

Read the article

CodePlex Daily Summary for Thursday, November 01, 2012

CodePlex Daily Summary for Thursday, November 01, 2012Popular ReleasesAccess 2010 Application Platform - Build Your Own Database: Application Platform - 0.0.1: Initial Release This is the first version of the database. At the moment is all contained in one file to make development easier, but the obvious idea would be to split it into Front and Back End for a production version of the tool. The features it contains at the moment are the "Core" features.Python Tools for Visual Studio: Python Tools for Visual Studio 1.5: We’re pleased to announce the release of Python Tools for Visual Studio 1.5 RTM. Python Tools for Visual Studio (PTVS) is an open-source plug-in for Visual Studio which supports programming with the Python language. PTVS supports a broad range of features including CPython/IronPython, Edit/Intellisense/Debug/Profile, Cloud, HPC, IPython, etc. support. For a quick overview of the general IDE experience, please watch this video There are a number of exciting improvement in this release comp...Devpad: 4.25: Whats new for Devpad 4.25: New Theme support New Export Wordpress Minor Bug Fix's, improvements and speed upsAssaultCube Reloaded: 2.5.5: Linux has Ubuntu 11.10 32-bit precompiled binaries and Ubuntu 10.10 64-bit precompiled binaries, but you can compile your own as it also contains the source. If you are using Mac or other operating systems, please wait while we try to package for those OSes. Try to compile it. If it fails, download a virtual machine. The server pack is ready for both Windows and Linux, but you might need to compile your own for Linux (source included) Changelog: Fixed potential bot bugs: Map change, OpenAL...Edi: Edi 1.0 with DarkExpression: Added DarkExpression theme (dialogs and message boxes are not completely themed, yet)MCEBuddy 2.x: MCEBuddy 2.3.6: Changelog for 2.3.6 (32bit and 64bit) 1. Fixed a bug in multichannel audio conversion failure. AAC does not support 6 channel audio, MCEBuddy now checks for it and force the output to 2 channel if AAC codec is specified 2. Fixed a bug in Original Broadcast Date and Time. Original Broadcast Date and Time is reported in UTC timezone in WTV metadata. TVDB and MovieDB dates are reported in network timezone. It is assumed the video is recorded and converted on the same machine, i.e. local timezone...MVVM Light Toolkit: MVVM Light Toolkit V4.1 for Visual Studio 2012: This version only supports Visual Studio 2012 (and all Express editions too). If you use Visual Studio 2010, please stay tuned, we will publish an update in a few days with support for VS10. V4.1 supports: Windows Phone 8 Windows 8 (Windows RT) Silverlight 5 Silverlight 4 WPF 4.5 WPF 4 WPF 3.5 And the following development environments: Visual Studio 2012 (Pro, Premium, Ultimate) Visual Studio 2012 Express for Windows 8 Visual Studio 2012 Express for Windows Phone 8 Visual...Microsoft Ajax Minifier: Microsoft Ajax Minifier 4.73: Fix issue in Discussion #401101 (unreferenced var in a for-in statement was getting removed). add the grouping operator to the parsed output so that unminified parsed code is closer to the original. Will still strip unneeded parens later, if minifying. more cleaning of references as they are minified out of the code.Liberty: v3.4.0.1 Release 28th October 2012: Change Log -Fixed -H4 Fixed the save verification screen showing incorrect mission and difficulty information for some saves -H4 Hopefully fixed the issue where progress did not save between missions and saves would not revert correctly -H3 Fixed crashes that occurred when trying to load player information -Proper exception dialogs will now show in place of crashesPlayer Framework by Microsoft: Player Framework for Windows 8 (Preview 7): This release is compatible with the version of the Smooth Streaming SDK released today (10/26). Release 1 of the player framework is expected to be available next week. IMPROVEMENTS & FIXESIMPORTANT: List of breaking changes from preview 6 Support for the latest smooth streaming SDK. Xaml only: Support for moving any of the UI elements outside the MediaPlayer (e.g. into the appbar). Note: Equivelent changes to the JS version due in coming week. Support for localizing all text used in t...Send multiple SMS via Way2SMS C#: SMS 1.1: Added support for 160by2Quick Launch: Quick Launch 1.0: A Lightweight and Fast Way to Manage and Launch Thousands of Tools and ApplicationsPress Win+Q and start to search and run. http://www.codeplex.com/Download?ProjectName=quicklaunch&DownloadId=523536Orchard Project: Orchard 1.6: Please read our release notes for Orchard 1.6: http://docs.orchardproject.net/Documentation/Orchard-1-6-Release-Notes Please do not post questions as reviews. Questions should be posted in the Discussions tab, where they will usually get promptly responded to. If you post a question as a review, you will pollute the rating, and you won't get an answer.Media Companion: Media Companion 3.507b: Once again, it has been some time since our release, and there have been a number changes since then. It is hoped that these changes will address some of the issues users have been experiencing, and of course, work continues! New Features: Added support for adding Home Movies. Option to sort Movies by votes. Added 'selectedBrowser' preference used when opening links in an external browser. Added option to fallback to getting runtime from the movie file if not available on IMDB. Added new Big...MSBuild Extension Pack: October 2012: Release Blog Post The MSBuild Extension Pack October 2012 release provides a collection of over 475 MSBuild tasks. A high level summary of what the tasks currently cover includes the following: System Items: Active Directory, Certificates, COM+, Console, Date and Time, Drives, Environment Variables, Event Logs, Files and Folders, FTP, GAC, Network, Performance Counters, Registry, Services, Sound Code: Assemblies, AsyncExec, CAB Files, Code Signing, DynamicExecute, File Detokenisation, GUI...NAudio: NAudio 1.6: Release notes at http://mark-dot-net.blogspot.co.uk/2012/10/naudio-16-release-notes-10th.htmlPowerShell Community Extensions: 2.1 Production: PowerShell Community Extensions 2.1 Release NotesOct 25, 2012 This version of PSCX supports both Windows PowerShell 2.0 and 3.0. See the ReleaseNotes.txt download above for more information.Umbraco CMS: Umbraco 4.9.1: Umbraco 4.9.1 is a bugfix release to fix major issues in 4.9.0 BugfixesThe full list of fixes can be found in the issue tracker's filtered results. A summary: Split buttons work again, you can now also scroll easier when the list is too long for the screen Media and Content pickers have information of the full path of the picked item Fixed: Publish status may not be accurate on nodes with large doctypes Fixed: 2 media folders and recycle bins after upgrade to 4.9 The template/code ...AcDown????? - AcDown Downloader Framework: AcDown????? v4.2.2: ??●AcDown??????????、??、??、???????。????，????，?????????????????????????。???????????Acfun、????(Bilibili)、??、??、YouTube、??、???、??????、SF????、????????????。 ●??????AcPlay?????，??????、????????????????。 ● AcDown??????????????????，????????????????????????????。 ● AcDown???????C#??，????.NET Framework 2.0??。?????"Acfun?????"。 ????32??64? Windows XP/Vista/7/8 ???? 32??64? ???Linux ????(1)????????Windows XP???，????????.NET Framework 2.0???(x86)，?????"?????????"??? (2)???????????Linux???，????????Mono?? ??2...Rawr: Rawr 5.0.2: This is the Downloadable WPF version of Rawr!For web-based version see http://elitistjerks.com/rawr.php You can find the version notes at: http://rawr.codeplex.com/wikipage?title=VersionNotes Rawr Addon (NOT UPDATED YET FOR MOP)We now have a Rawr Official Addon for in-game exporting and importing of character data hosted on Curse. The Addon does not perform calculations like Rawr, it simply shows your exported Rawr data in wow tooltips and lets you export your character to Rawr (including ba...New ProjectsAsbesto: Proyecto grupo: "2ravas" para Laboratorio de Computación IV de la carrera TSP de la UTN-FRGP Realizado en C# y ASP.NET en Visual Studio 2012 y SQL Server 2012C++ Diamond printer on console without if statement: prints just a diamond with stars(*). only one important and funny feature is that it's not using 'if' statement. C++ used.CloudTest: Test cloud computing projectEnumeration of objects Class Library C#: At core level in Java I like extension of traditional enum type permiting use as the elements instances of a class. The project implements the same idea by C# with some more advanced features like a set type with boolean operators extending idea of FlagsAttributeEquation Inversion: Visual Studion 2008 Add-in for equation inversions.ESENT Serialization Class Library: ESENT Serialization class library is built above Managed ESENT. It allows you to store your objects in the underlying extensible storage engine database.ForceHttps: Very simple httpModule to ensure that all http requests are https. 1. Drop the dll into your website's bin directory 2. Update httpModules section of your web.config to reference the dll 3. Make sure your Web Server can handle SSL requests for the URL ALL http requests will be redirected as https.forrajeriaPAV2: tp pav2 asd as asd as fasfjaijiasjifoa as asf asf as afs fas asf afs fsaGoogle Analytics for WinRT: A Windows Store (WinRT) class library for tracking Google Analytics page views, events, and custom variables for your Metro style desktop and tablet apps.huanglitest10312: mvc projectiMan: iMan will be your own port manager, which help to provide the information about all the ports open in your PC It's completely developed in .NET C#InjectionCop: Facilitates secure coding through static code analysis and contract annotations in the Common Language Infrastructure.Master of Olympus: Remake of Master of Olympus : Zeus, a game developed by Impressions Games in 2000.MediaScribe: MediaScribe is a note app for your media.MouseNestDotNet: A small personal website application.Project Estimator ???????? ?? ?????????????? ?? ???????: Project Estimator ? ???????? ??????????? ? ??????????? ?? ????? ? ???????? ????.Projekt grupowy 1: Project created only for school purpose.SecondHandApp: Warenwirtschaftsprogramm für denn SecondHand LädenSimple .NET XML Serialization: .NET's XML serialization using Linq XObject classes EG: XElement in an IXmlSerializable base classStrip Converter: A Very Handy Converter for 2D Games Developers Developer Website: http://www.bluebulk.infoSwitch JS Control (Client Side): Switch JS control is a very light client side library to create switch(es) on web applications or mobile applications.VisaSys: Visa System????????: TODO::????

Read the article

Permissions denied on apache rewrite module virtual host configuration

- by sina

All of a sudden I keep getting "Permissions denied" on apache 2 virtualhost once we moved it to its own conf file. I have tried all the suggestions I have found here but none work. Please can someone tell me what I am doing wrong? Thanks! <VirtualHost *:80> DocumentRoot "/var/www/mm" <Directory "/var/www/mm"> Options +Indexes +MultiViews +FollowSymLinks AllowOverride all Order deny,allow Allow from all AddType text/vnd.sun.j2me.app-descriptor .jad AddType application/vnd.rim.cod .cod </Directory> Alias /holdspace "/var/www/mm/holdspace" RewriteLogLevel 9 RewriteLog "/var/log/httpd/rewrite.log" RewriteEngine on # 91xx RewriteCond %{HTTP_USER_AGENT} BlackBerry.9105 RewriteRule ^/download/(.*) /holdspace/bb6-360x480/$1 [L] # 92xx RewriteCond %{HTTP_USER_AGENT} BlackBerry.9220 RewriteRule ^/download/(.*) /holdspace/bb5-320x240/$1 [L] Errors in error.log: [Wed May 28 12:44:58 2014] [error] [client 197.255.173.95] (13)Permission denied: access to /download/eazymoney.jad denied [Wed May 28 12:44:58 2014] [error] [client 197.255.173.95] (13)Permission denied: access to /error/HTTP_FORBIDDEN.html.var denied [Wed May 28 12:44:59 2014] [error] [client 197.255.173.95] (13)Permission denied: access to /favicon.ico denied [Wed May 28 12:44:59 2014] [error] [client 197.255.173.95] (13)Permission denied: access to /error/HTTP_FORBIDDEN.html.var denied [Wed May 28 12:44:59 2014] [error] [client 197.255.173.95] (13)Permission denied: access to /favicon.ico denied [Wed May 28 12:44:59 2014] [error] [client 197.255.173.95] (13)Permission denied: access to /error/HTTP_FORBIDDEN.html.var denied Errors in rewrite.log: 197.255.173.95 - - [28/May/2014:12:46:01 +0100] [41.203.113.103/sid#7fe41704ca28][rid#7fe417123378/initial/redir#1] (3) applying pattern '^/download/(.*)' to uri '/error/HTTP_FORBIDDEN.html.var' 197.255.173.95 - - [28/May/2014:12:46:01 +0100] [41.203.113.103/sid#7fe41704ca28][rid#7fe417123378/initial/redir#1] (3) applying pattern '^/download/(.*)' to uri '/error/HTTP_FORBIDDEN.html.var' Apache Configuration file: ServerTokens Prod ServerRoot "/etc/httpd" PidFile run/httpd.pid Timeout 60 KeepAlive Off MaxKeepAliveRequests 100 KeepAliveTimeout 15 <IfModule prefork.c> StartServers 8 MinSpareServers 5 MaxSpareServers 20 ServerLimit 256 MaxClients 256 MaxRequestsPerChild 4000 </IfModule> <IfModule worker.c> StartServers 4 MaxClients 300 MinSpareThreads 25 MaxSpareThreads 75 ThreadsPerChild 25 MaxRequestsPerChild 0 </IfModule> Listen 80 LoadModule auth_basic_module modules/mod_auth_basic.so LoadModule auth_digest_module modules/mod_auth_digest.so LoadModule authn_file_module modules/mod_authn_file.so LoadModule authn_alias_module modules/mod_authn_alias.so LoadModule authn_anon_module modules/mod_authn_anon.so LoadModule authn_dbm_module modules/mod_authn_dbm.so LoadModule authn_default_module modules/mod_authn_default.so LoadModule authz_host_module modules/mod_authz_host.so LoadModule authz_user_module modules/mod_authz_user.so LoadModule authz_owner_module modules/mod_authz_owner.so LoadModule authz_groupfile_module modules/mod_authz_groupfile.so LoadModule authz_dbm_module modules/mod_authz_dbm.so LoadModule authz_default_module modules/mod_authz_default.so LoadModule ldap_module modules/mod_ldap.so LoadModule authnz_ldap_module modules/mod_authnz_ldap.so LoadModule include_module modules/mod_include.so LoadModule log_config_module modules/mod_log_config.so LoadModule logio_module modules/mod_logio.so LoadModule env_module modules/mod_env.so LoadModule ext_filter_module modules/mod_ext_filter.so LoadModule mime_magic_module modules/mod_mime_magic.so LoadModule expires_module modules/mod_expires.so LoadModule deflate_module modules/mod_deflate.so LoadModule headers_module modules/mod_headers.so LoadModule usertrack_module modules/mod_usertrack.so LoadModule setenvif_module modules/mod_setenvif.so LoadModule mime_module modules/mod_mime.so LoadModule dav_module modules/mod_dav.so LoadModule status_module modules/mod_status.so LoadModule autoindex_module modules/mod_autoindex.so LoadModule info_module modules/mod_info.so LoadModule dav_fs_module modules/mod_dav_fs.so LoadModule vhost_alias_module modules/mod_vhost_alias.so LoadModule negotiation_module modules/mod_negotiation.so LoadModule dir_module modules/mod_dir.so LoadModule actions_module modules/mod_actions.so LoadModule speling_module modules/mod_speling.so LoadModule userdir_module modules/mod_userdir.so LoadModule alias_module modules/mod_alias.so LoadModule substitute_module modules/mod_substitute.so LoadModule rewrite_module modules/mod_rewrite.so LoadModule proxy_module modules/mod_proxy.so LoadModule proxy_ftp_module modules/mod_proxy_ftp.so LoadModule proxy_http_module modules/mod_proxy_http.so LoadModule proxy_ajp_module modules/mod_proxy_ajp.so LoadModule proxy_connect_module modules/mod_proxy_connect.so LoadModule cache_module modules/mod_cache.so LoadModule suexec_module modules/mod_suexec.so LoadModule disk_cache_module modules/mod_disk_cache.so LoadModule cgi_module modules/mod_cgi.so LoadModule version_module modules/mod_version.so Include conf.d/*.conf User apache Group apache ServerAdmin root@localhost ServerName sv001zma002.africa.int.myorg.com UseCanonicalName Off DocumentRoot "/var/www/html" <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory "/var/www/html"> Options FollowSymLinks AllowOverride None Order allow,deny Allow from all </Directory> <IfModule mod_userdir.c> UserDir disabled </IfModule> DirectoryIndex index.html index.html.var AccessFileName .htaccess <Files ~ "^\.ht"> Order allow,deny Deny from all Satisfy All </Files> TypesConfig /etc/mime.types DefaultType text/plain <IfModule mod_mime_magic.c> MIMEMagicFile conf/magic </IfModule> HostnameLookups Off ErrorLog logs/error_log LogLevel warn LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %b" common LogFormat "%{Referer}i -> %U" referer LogFormat "%{User-agent}i" agent CustomLog logs/access_log combined ServerSignature Off TraceEnable Off Alias /icons/ "/var/www/icons/" <Directory "/var/www/icons"> Options MultiViews FollowSymLinks AllowOverride None Order allow,deny Allow from all </Directory> <IfModule mod_dav_fs.c> DAVLockDB /var/lib/dav/lockdb </IfModule> ScriptAlias /cgi-bin/ "/var/www/cgi-bin/" <Directory "/var/www/cgi-bin"> AllowOverride None Options None Order allow,deny Allow from all </Directory> IndexOptions FancyIndexing VersionSort NameWidth=* HTMLTable Charset=UTF-8 AddIconByEncoding (CMP,/icons/compressed.gif) x-compress x-gzip AddIconByType (TXT,/icons/text.gif) text/* AddIconByType (IMG,/icons/image2.gif) image/* AddIconByType (SND,/icons/sound2.gif) audio/* AddIconByType (VID,/icons/movie.gif) video/* AddIcon /icons/binary.gif .bin .exe AddIcon /icons/binhex.gif .hqx AddIcon /icons/tar.gif .tar AddIcon /icons/world2.gif .wrl .wrl.gz .vrml .vrm .iv AddIcon /icons/compressed.gif .Z .z .tgz .gz .zip AddIcon /icons/a.gif .ps .ai .eps AddIcon /icons/layout.gif .html .shtml .htm .pdf AddIcon /icons/text.gif .txt AddIcon /icons/c.gif .c AddIcon /icons/p.gif .pl .py AddIcon /icons/f.gif .for AddIcon /icons/dvi.gif .dvi AddIcon /icons/uuencoded.gif .uu AddIcon /icons/script.gif .conf .sh .shar .csh .ksh .tcl AddIcon /icons/tex.gif .tex AddIcon /icons/bomb.gif core AddIcon /icons/back.gif .. AddIcon /icons/hand.right.gif README AddIcon /icons/folder.gif ^^DIRECTORY^^ AddIcon /icons/blank.gif ^^BLANKICON^^ DefaultIcon /icons/unknown.gif ReadmeName README.html HeaderName HEADER.html IndexIgnore .??* *~ *# HEADER* README* RCS CVS *,v *,t AddLanguage ca .ca AddLanguage cs .cz .cs AddLanguage da .dk AddLanguage de .de AddLanguage el .el AddLanguage en .en AddLanguage eo .eo AddLanguage es .es AddLanguage et .et AddLanguage fr .fr AddLanguage he .he AddLanguage hr .hr AddLanguage it .it AddLanguage ja .ja AddLanguage ko .ko AddLanguage ltz .ltz AddLanguage nl .nl AddLanguage nn .nn AddLanguage no .no AddLanguage pl .po AddLanguage pt .pt AddLanguage pt-BR .pt-br AddLanguage ru .ru AddLanguage sv .sv AddLanguage zh-CN .zh-cn AddLanguage zh-TW .zh-tw LanguagePriority en ca cs da de el eo es et fr he hr it ja ko ltz nl nn no pl pt pt-BR ru sv zh-CN zh-TW ForceLanguagePriority Prefer Fallback AddDefaultCharset UTF-8 AddType application/x-compress .Z AddType application/x-gzip .gz .tgz AddType application/x-x509-ca-cert .crt AddType application/x-pkcs7-crl .crl AddHandler type-map var AddType text/html .shtml AddOutputFilter INCLUDES .shtml ProxyErrorOverride On Alias /error/ "/var/www/error/" <IfModule mod_negotiation.c> <IfModule mod_include.c> <Directory "/var/www/error"> AllowOverride None Options IncludesNoExec AddOutputFilter Includes html AddHandler type-map var Order allow,deny Allow from all LanguagePriority en es de fr ForceLanguagePriority Prefer Fallback </Directory> ErrorDocument 400 /error/HTTP_BAD_REQUEST.html.var ErrorDocument 401 /error/HTTP_UNAUTHORIZED.html.var ErrorDocument 403 /error/HTTP_FORBIDDEN.html.var ErrorDocument 404 /error/HTTP_NOT_FOUND.html.var </IfModule> </IfModule> BrowserMatch "Mozilla/2" nokeepalive BrowserMatch "MSIE 4\.0b2;" nokeepalive downgrade-1.0 force-response-1.0 BrowserMatch "RealPlayer 4\.0" force-response-1.0 BrowserMatch "Java/1\.0" force-response-1.0 BrowserMatch "JDK/1\.0" force-response-1.0 BrowserMatch "Microsoft Data Access Internet Publishing Provider" redirect-carefully BrowserMatch "MS FrontPage" redirect-carefully BrowserMatch "^WebDrive" redirect-carefully BrowserMatch "^WebDAVFS/1.[0123]" redirect-carefully BrowserMatch "^gnome-vfs/1.0" redirect-carefully BrowserMatch "^XML Spy" redirect-carefully BrowserMatch "^Dreamweaver-WebDAV-SCM1" redirect-carefully ErrorDocument 400 "Bad Request"

Read the article

3D Graphics with XNA Game Studio 4.0 bug in light map?

- by Eibis

i'm following the tutorials on 3D Graphics with XNA Game Studio 4.0 and I came up with an horrible effect when I tried to implement the Light Map http://i.stack.imgur.com/BUWvU.jpg this effect shows up when I look towards the center of the house (and it moves with me). it has this shape because I'm using a sphere to represent light; using other light shapes gives different results. I'm using a class PreLightingRenderer: using System; using System.Collections.Generic; using System.Linq; using System.Text; using Microsoft.Xna.Framework; using Microsoft.Xna.Framework.Graphics; using Dhpoware; using Microsoft.Xna.Framework.Content; namespace XNAFirstPersonCamera { public class PrelightingRenderer { // Normal, depth, and light map render targets RenderTarget2D depthTarg; RenderTarget2D normalTarg; RenderTarget2D lightTarg; // Depth/normal effect and light mapping effect Effect depthNormalEffect; Effect lightingEffect; // Point light (sphere) mesh Model lightMesh; // List of models, lights, and the camera public List<CModel> Models { get; set; } public List<PPPointLight> Lights { get; set; } public FirstPersonCamera Camera { get; set; } GraphicsDevice graphicsDevice; int viewWidth = 0, viewHeight = 0; public PrelightingRenderer(GraphicsDevice GraphicsDevice, ContentManager Content) { viewWidth = GraphicsDevice.Viewport.Width; viewHeight = GraphicsDevice.Viewport.Height; // Create the three render targets depthTarg = new RenderTarget2D(GraphicsDevice, viewWidth, viewHeight, false, SurfaceFormat.Single, DepthFormat.Depth24); normalTarg = new RenderTarget2D(GraphicsDevice, viewWidth, viewHeight, false, SurfaceFormat.Color, DepthFormat.Depth24); lightTarg = new RenderTarget2D(GraphicsDevice, viewWidth, viewHeight, false, SurfaceFormat.Color, DepthFormat.Depth24); // Load effects depthNormalEffect = Content.Load<Effect>(@"Effects\PPDepthNormal"); lightingEffect = Content.Load<Effect>(@"Effects\PPLight"); // Set effect parameters to light mapping effect lightingEffect.Parameters["viewportWidth"].SetValue(viewWidth); lightingEffect.Parameters["viewportHeight"].SetValue(viewHeight); // Load point light mesh and set light mapping effect to it lightMesh = Content.Load<Model>(@"Models\PPLightMesh"); lightMesh.Meshes[0].MeshParts[0].Effect = lightingEffect; this.graphicsDevice = GraphicsDevice; } public void Draw() { drawDepthNormalMap(); drawLightMap(); prepareMainPass(); } void drawDepthNormalMap() { // Set the render targets to 'slots' 1 and 2 graphicsDevice.SetRenderTargets(normalTarg, depthTarg); // Clear the render target to 1 (infinite depth) graphicsDevice.Clear(Color.White); // Draw each model with the PPDepthNormal effect foreach (CModel model in Models) { model.CacheEffects(); model.SetModelEffect(depthNormalEffect, false); model.Draw(Camera.ViewMatrix, Camera.ProjectionMatrix, Camera.Position); model.RestoreEffects(); } // Un-set the render targets graphicsDevice.SetRenderTargets(null); } void drawLightMap() { // Set the depth and normal map info to the effect lightingEffect.Parameters["DepthTexture"].SetValue(depthTarg); lightingEffect.Parameters["NormalTexture"].SetValue(normalTarg); // Calculate the view * projection matrix Matrix viewProjection = Camera.ViewMatrix * Camera.ProjectionMatrix; // Set the inverse of the view * projection matrix to the effect Matrix invViewProjection = Matrix.Invert(viewProjection); lightingEffect.Parameters["InvViewProjection"].SetValue(invViewProjection); // Set the render target to the graphics device graphicsDevice.SetRenderTarget(lightTarg); // Clear the render target to black (no light) graphicsDevice.Clear(Color.Black); // Set render states to additive (lights will add their influences) graphicsDevice.BlendState = BlendState.Additive; graphicsDevice.DepthStencilState = DepthStencilState.None; foreach (PPPointLight light in Lights) { // Set the light's parameters to the effect light.SetEffectParameters(lightingEffect); // Calculate the world * view * projection matrix and set it to // the effect Matrix wvp = (Matrix.CreateScale(light.Attenuation) * Matrix.CreateTranslation(light.Position)) * viewProjection; lightingEffect.Parameters["WorldViewProjection"].SetValue(wvp); // Determine the distance between the light and camera float dist = Vector3.Distance(Camera.Position, light.Position); // If the camera is inside the light-sphere, invert the cull mode // to draw the inside of the sphere instead of the outside if (dist < light.Attenuation) graphicsDevice.RasterizerState = RasterizerState.CullClockwise; // Draw the point-light-sphere lightMesh.Meshes[0].Draw(); // Revert the cull mode graphicsDevice.RasterizerState = RasterizerState.CullCounterClockwise; } // Revert the blending and depth render states graphicsDevice.BlendState = BlendState.Opaque; graphicsDevice.DepthStencilState = DepthStencilState.Default; // Un-set the render target graphicsDevice.SetRenderTarget(null); } void prepareMainPass() { foreach (CModel model in Models) foreach (ModelMesh mesh in model.Model.Meshes) foreach (ModelMeshPart part in mesh.MeshParts) { // Set the light map and viewport parameters to each model's effect if (part.Effect.Parameters["LightTexture"] != null) part.Effect.Parameters["LightTexture"].SetValue(lightTarg); if (part.Effect.Parameters["viewportWidth"] != null) part.Effect.Parameters["viewportWidth"].SetValue(viewWidth); if (part.Effect.Parameters["viewportHeight"] != null) part.Effect.Parameters["viewportHeight"].SetValue(viewHeight); } } } } that uses three effect: PPDepthNormal.fx float4x4 World; float4x4 View; float4x4 Projection; struct VertexShaderInput { float4 Position : POSITION0; float3 Normal : NORMAL0; }; struct VertexShaderOutput { float4 Position : POSITION0; float2 Depth : TEXCOORD0; float3 Normal : TEXCOORD1; }; VertexShaderOutput VertexShaderFunction(VertexShaderInput input) { VertexShaderOutput output; float4x4 viewProjection = mul(View, Projection); float4x4 worldViewProjection = mul(World, viewProjection); output.Position = mul(input.Position, worldViewProjection); output.Normal = mul(input.Normal, World); // Position's z and w components correspond to the distance // from camera and distance of the far plane respectively output.Depth.xy = output.Position.zw; return output; } // We render to two targets simultaneously, so we can't // simply return a float4 from the pixel shader struct PixelShaderOutput { float4 Normal : COLOR0; float4 Depth : COLOR1; }; PixelShaderOutput PixelShaderFunction(VertexShaderOutput input) { PixelShaderOutput output; // Depth is stored as distance from camera / far plane distance // to get value between 0 and 1 output.Depth = input.Depth.x / input.Depth.y; // Normal map simply stores X, Y and Z components of normal // shifted from (-1 to 1) range to (0 to 1) range output.Normal.xyz = (normalize(input.Normal).xyz / 2) + .5; // Other components must be initialized to compile output.Depth.a = 1; output.Normal.a = 1; return output; } technique Technique1 { pass Pass1 { VertexShader = compile vs_1_1 VertexShaderFunction(); PixelShader = compile ps_2_0 PixelShaderFunction(); } } PPLight.fx float4x4 WorldViewProjection; float4x4 InvViewProjection; texture2D DepthTexture; texture2D NormalTexture; sampler2D depthSampler = sampler_state { texture = ; minfilter = point; magfilter = point; mipfilter = point; }; sampler2D normalSampler = sampler_state { texture = ; minfilter = point; magfilter = point; mipfilter = point; }; float3 LightColor; float3 LightPosition; float LightAttenuation; // Include shared functions #include "PPShared.vsi" struct VertexShaderInput { float4 Position : POSITION0; }; struct VertexShaderOutput { float4 Position : POSITION0; float4 LightPosition : TEXCOORD0; }; VertexShaderOutput VertexShaderFunction(VertexShaderInput input) { VertexShaderOutput output; output.Position = mul(input.Position, WorldViewProjection); output.LightPosition = output.Position; return output; } float4 PixelShaderFunction(VertexShaderOutput input) : COLOR0 { // Find the pixel coordinates of the input position in the depth // and normal textures float2 texCoord = postProjToScreen(input.LightPosition) + halfPixel(); // Extract the depth for this pixel from the depth map float4 depth = tex2D(depthSampler, texCoord); // Recreate the position with the UV coordinates and depth value float4 position; position.x = texCoord.x * 2 - 1; position.y = (1 - texCoord.y) * 2 - 1; position.z = depth.r; position.w = 1.0f; // Transform position from screen space to world space position = mul(position, InvViewProjection); position.xyz /= position.w; // Extract the normal from the normal map and move from // 0 to 1 range to -1 to 1 range float4 normal = (tex2D(normalSampler, texCoord) - .5) * 2; // Perform the lighting calculations for a point light float3 lightDirection = normalize(LightPosition - position); float lighting = clamp(dot(normal, lightDirection), 0, 1); // Attenuate the light to simulate a point light float d = distance(LightPosition, position); float att = 1 - pow(d / LightAttenuation, 6); return float4(LightColor * lighting * att, 1); } technique Technique1 { pass Pass1 { VertexShader = compile vs_1_1 VertexShaderFunction(); PixelShader = compile ps_2_0 PixelShaderFunction(); } } PPShared.vsi has some common functions: float viewportWidth; float viewportHeight; // Calculate the 2D screen position of a 3D position float2 postProjToScreen(float4 position) { float2 screenPos = position.xy / position.w; return 0.5f * (float2(screenPos.x, -screenPos.y) + 1); } // Calculate the size of one half of a pixel, to convert // between texels and pixels float2 halfPixel() { return 0.5f / float2(viewportWidth, viewportHeight); } and finally from the Game class I set up in LoadContent with: effect = Content.Load(@"Effects\PPModel"); models[0] = new CModel(Content.Load(@"Models\teapot"), new Vector3(-50, 80, 0), new Vector3(0, 0, 0), 1f, Content.Load(@"Textures\prova_texture_autocad"), GraphicsDevice); house = new CModel(Content.Load(@"Models\house"), new Vector3(0, 0, 0), new Vector3((float)-Math.PI / 2, 0, 0), 35.0f, Content.Load(@"Textures\prova_texture_autocad"), GraphicsDevice); models[0].SetModelEffect(effect, true); house.SetModelEffect(effect, true); renderer = new PrelightingRenderer(GraphicsDevice, Content); renderer.Models = new List(); renderer.Models.Add(house); renderer.Models.Add(models[0]); renderer.Lights = new List() { new PPPointLight(new Vector3(0, 120, 0), Color.White * .85f, 2000) }; where PPModel.fx is: float4x4 World; float4x4 View; float4x4 Projection; texture2D BasicTexture; sampler2D basicTextureSampler = sampler_state { texture = ; addressU = wrap; addressV = wrap; minfilter = anisotropic; magfilter = anisotropic; mipfilter = linear; }; bool TextureEnabled = true; texture2D LightTexture; sampler2D lightSampler = sampler_state { texture = ; minfilter = point; magfilter = point; mipfilter = point; }; float3 AmbientColor = float3(0.15, 0.15, 0.15); float3 DiffuseColor; #include "PPShared.vsi" struct VertexShaderInput { float4 Position : POSITION0; float2 UV : TEXCOORD0; }; struct VertexShaderOutput { float4 Position : POSITION0; float2 UV : TEXCOORD0; float4 PositionCopy : TEXCOORD1; }; VertexShaderOutput VertexShaderFunction(VertexShaderInput input) { VertexShaderOutput output; float4x4 worldViewProjection = mul(World, mul(View, Projection)); output.Position = mul(input.Position, worldViewProjection); output.PositionCopy = output.Position; output.UV = input.UV; return output; } float4 PixelShaderFunction(VertexShaderOutput input) : COLOR0 { // Sample model's texture float3 basicTexture = tex2D(basicTextureSampler, input.UV); if (!TextureEnabled) basicTexture = float4(1, 1, 1, 1); // Extract lighting value from light map float2 texCoord = postProjToScreen(input.PositionCopy) + halfPixel(); float3 light = tex2D(lightSampler, texCoord); light += AmbientColor; return float4(basicTexture * DiffuseColor * light, 1); } technique Technique1 { pass Pass1 { VertexShader = compile vs_1_1 VertexShaderFunction(); PixelShader = compile ps_2_0 PixelShaderFunction(); } } I don't have any idea on what's wrong... googling the web I found that this tutorial may have some bug but I don't know if it's the LightModel fault (the sphere) or in a shader or in the class PrelightingRenderer. Any help is very appreciated, thank you for reading!

Read the article

Tips for XNA WP7 Developers

- by Michael B. McLaughlin

There are several things any XNA developer should know/consider when coming to the Windows Phone 7 platform. This post assumes you are familiar with the XNA Framework and with the changes between XNA 3.1 and XNA 4.0. It’s not exhaustive; it’s simply a list of things I’ve gathered over time. I may come back and add to it over time, and I’m happy to add anything anyone else has experienced or learned as well. Display · The screen is either 800x480 or 480x800. · But you aren’t required to use only those resolutions. · The hardware scaler on the phone will scale up from 240x240. · One dimension will be capped at 800 and the other at 480; which depends on your code, but you cannot have, e.g., an 800x600 back buffer – that will be created as 800x480. · The hardware scaler will not normally change aspect ratio, though, so no unintended stretching. · Any dimension (width, height, or both) below 240 will be adjusted to 240 (without any aspect ratio adjustment such that, e.g. 200x240 will be treated as 240x240). · Dimensions below 240 will be honored in terms of calculating whether to use portrait or landscape. · If dimensions are exactly equal or if height is greater than width then game will be in portrait. · If width is greater than height, the game will be in landscape. · Landscape games will automatically flip if the user turns the phone 180°; no code required. · Default landscape is top = left. In other words a user holding a phone who starts a landscape game will see the first image presented so that the “top” of the screen is along the right edge of his/her phone, such that the natural behavior would be to turn the phone 90° so that the top of the phone will be held in the user’s left hand and the bottom would be held in the user’s right hand. · The status bar (where the clock, battery power, etc., are found) is hidden when the Game-derived class sets GraphicsDeviceManager.IsFullScreen = true. It is shown when IsFullScreen = false. The default value is false (i.e. the status bar is shown). · You should have a good reason for hiding the status bar. Users find it helpful to know what time it is, how much charge their battery has left, and whether or not their phone is in service range. This is especially true for casual games that you expect someone to play for a few minutes at a time, e.g. while waiting for some event to start, for a phone call to come in, or for a train, bus, or subway to arrive. · In portrait mode, the status bar occupies 32 pixels of space. This means that a game with a back buffer of 480x800 will be scaled down to occupy approximately 461x768 screen pixels. Setting the back buffer to 480x768 (or some resolution with the same 0.625 aspect ratio) will avoid this scaling. · In landscape mode, the status bar occupies 72 pixels of space. This means that a game with a back buffer of 800x480 will be scaled down to occupy approximately 728x437 screen pixels. Setting the back buffer to 728x480 (or some resolution with the same 1.51666667 aspect ratio) will avoid this scaling. Input · Touch input is scaled with screen size. · So if your back buffer is 600x360, a tap in the bottom right corner will come in as (599,359). You don’t need to do anything special to get this automatic scaling of touch behavior. · If you do not use full area of the screen, any touch input outside the area you use will still register as a touch input. For example, if you set a portrait resolution of 240x240, it would be scaled up to occupy a 480x480 area, centered in the screen. If you touch anywhere above this area, you will get a touch input of (X,0) where X is a number from 0 to 239 (in accordance with your 240 pixel wide back buffer). Any touch below this area will give a touch input of (X,239). · If you keep the status bar visible, touches within its area will not be passed to your game. · In general, a screen measurement is the diagonal. So a 3.5” screen is 3.5” long from the bottom right corner to the top left corner. With an aspect ratio of 0.6 (480/800 = 0.6), this means that a phone with a 3.5” screen is only approximately 1.8” wide by 3” tall. So there are approximately 267 pixels in an inch on a 3.5” screen. · Again, this time in metric! 3.5 inches is approximately 8.89 cm. So an 8.89 cm screen is 8.89 cm long from the bottom right corner to the top left corner. With an aspect ratio of 0.6, this means that a phone with an 8.89 cm screen is only approximately 4.57 cm wide by 7.62 cm tall. So there are approximately 105 pixels in a centimeter on an 8.89 cm screen. · Think about the size of your finger tip. If you do not have large hands, think about the size of the fingertip of someone with large hands. Consider that when you are sizing your touch input. Especially consider that when you are spacing two touch targets near one another. You need to judge it for yourself, but items that are next to each other and are each 100x100 should be fine when it comes to selecting items individually. Smaller targets than that are ok provided that you leave space between them. · You want your users to have a pleasant experience. Making touch controls too small or too close to one another will make them nervous about whether they will touch the right target. Take this into account when you plan out your game initially. If possible, do some quick size mockups on an actual phone using colored rectangles that you position and size where you plan to have your game controls. Adjust as necessary. · People do not have transparent hands! Nor are their hands the size of a mouse pointer icon. Consider leaving a dedicated space for input rather than forcing the user to cover up to one-third of the screen with a finger just to play the game. · Another benefit of designing your controls to use a dedicated area is that you’re less likely to have players moving their finger(s) so frantically that they accidentally hit the back button, start button, or search button (many phones have one or more of these on the screen itself – it’s easy to hit one by accident and really annoying if you hit, e.g., the search button and then quickly tap back only to find out that the game didn’t save your progress such that you just wasted all the time you spent playing). · People do not like doing somersaults in order to move something forward with accelerometer-based controls. Test your accelerometer-based controls extensively and get a lot of feedback. Very well-known games from noted publishers have created really bad accelerometer controls and been virtually unplayable as a result. Also be wary of exceptions and other possible failures that the documentation warns about. · When done properly, the accelerometer can add a nice touch to your game (see, e.g. ilomilo where the accelerometer was used to move the background; it added a nice touch without frustrating the user; I also think CarniVale does direct accelerometer controls very well). However, if done poorly, it will make your game an abomination unto the Marketplace. Days, weeks, perhaps even months of development time that you will never get back. I won’t name names; you can search the marketplace for games with terrible reviews and you’ll find them. Graphics · The maximum frame rate is 30 frames per second. This was set as a compromise between battery life and quality. · At least one model of phone is known to have a screen refresh rate that is between 59 and 60 hertz. Because of this, using a fixed time step with a target frame rate of 30 will cause a slight internal delay to build up as the framework is forced to wait slightly for the next refresh. Eventually the delay will get to the point where a draw is skipped in order to recover from the delay. (See Nick's comment below for clarification.) · To deal with that delay, you can either stay with a fixed time step and set the frame rate slightly lower or else you can go to a variable time step and make sure to adjust all of your update data (e.g. player movement distance) to take into account the elapsed time from the last update. A variable time step makes your update logic slightly more complicated but will avoid frame skips entirely. · Currently there are no custom shaders. This might change in the future (there is no hardware limitation preventing it; it simply wasn’t a feature that could be implemented in the time available before launch). · There are five built-in shaders. You can create a lot of nice effects with the built-in shaders. · There is more power on the CPU than there is on the GPU so things you might typically off-load to the GPU will instead make sense to do on the CPU side. · This is a phone. It is not a PC. It is not an Xbox 360. The emulator runs on a PC and uses the full power of your PC. It is very good for testing your code for bugs and doing early prototyping and layout. You should not use it to measure performance. Use actual phone hardware instead. · There are many phone models, each of which has slightly different performance levels for I/O, screen blitting, CPU performance, etc. Do not take your game right to the performance limit on your phone since for some other phones you might be crossing their limits and leaving players with a bad experience. Leave a cushion to account for hardware differences. · Smaller screened phones will have slightly more dots per inch (dpi). Larger screened phones will have slightly less. Either way, the dpi will be much higher than the typical 96 found on most computer screens. Make sure that whoever is doing art for your game takes this into account. · Screens are only required to have 16 bit color (65,536 colors). This is common among smart phones. Using gradients on a 16 bit display can produce an ugly artifact known as banding. Banding is when, rather than a smooth transition from one color to another, you instead see distinct lines. Be careful to avoid this when possible. Banding can be avoided through careful art creation. Its effects can be minimized and even unnoticeable when the texture in question is always moving. You should be careful not to rely on “looks good on my phone” since some phones do have 32-bit displays and thus you’ll find yourself wondering why you’re getting bad reviews that complain about the graphics. Avoid gradients; if you can’t, make sure they are 16-bit safe. Audio · Never rely on sounds as your sole signal to the player that something is happening in the game. They might have the sound off. They might be playing somewhere loud. Etc. · You have to provide controls to disable sound & music. These should be separate. · On at least one model of phone, the volume control API currently has no effect. Players can adjust sound with their hardware volume buttons, but in game selectors simply won’t work. As such, it may not be worth the effort of providing anything beyond on/off switches for sound and music. · MediaPlayer.GameHasControl will return true when a game is hooked up to a PC running Zune. When Zune is running, any attempts to do anything (beyond check GameHasControl) with MediaPlayer will cause an exception to be thrown. If this exception is thrown, catch it and disable music. Exceptions take time to propagate; you don’t want one popping up in every single run of your game’s Update method. · Remember that players can already be listening to music or using the FM radio. In this case GameHasControl will be false and you should handle this appropriately. You can, alternately, ask the player for permission to stop their current music and play your music instead, but the (current) requirement that you restore their music when done is very hard (if not impossible) to deal with. · You can still play sound effects even when the game doesn’t have control of the music, but don’t think this is a backdoor to playing music. Your game will fail certification if your “sound effect” seems to be more like music in scope and length.

Read the article

Using CSS3 media queries in HTML 5 pages

- by nikolaosk

This is going to be the seventh post in a series of posts regarding HTML 5. You can find the other posts here , here , here, here , here and here. In this post I will provide a hands-on example on how to use CSS 3 Media Queries in HTML 5 pages. This is a very important feature since nowadays lots of users view websites through their mobile devices. Web designers were able to define media-specific style sheets for quite a while, but have been limited to the type of output. The output could only be Screen, Print .The way we used to do things before CSS 3 was to have separate CSS files and the browser decided which style sheet to use. Please have a look at the snippet below - HTML 4 media queries <link rel="stylesheet" type="text/css" media="screen" href="styles.css"> <link rel="stylesheet" type="text/css" media="print" href="print-styles.css"> ?he browser determines which style to use. With CSS 3 we can have all media queries in one stylesheet. Media queries can determine the resolution of the device, the orientation of the device, the width and height of the device and the width and height of the browser window.We can also include CSS 3 media queries in separate stylesheets. In order to be absolutely clear this is not (and could not be) a detailed tutorial on HTML 5. There are other great resources for that.Navigate to the excellent interactive tutorials of W3School. Another excellent resource is HTML 5 Doctor. Two very nice sites that show you what features and specifications are implemented by various browsers and their versions are http://caniuse.com/ and http://html5test.com/. At this times Chrome seems to support most of HTML 5 specifications.Another excellent way to find out if the browser supports HTML 5 and CSS 3 features is to use the Javascript lightweight library Modernizr. In this hands-on example I will be using Expression Web 4.0.This application is not a free application. You can use any HTML editor you like.You can use Visual Studio 2012 Express edition. You can download it here. Before I go on with the actual demo I will use the (http://www.caniuse.com) to see the support for CSS 3 Media Queries from the latest versions of modern browsers. Please have a look at the picture below. We see that all the latest versions of modern browsers support this feature. We can see that even IE 9 supports this feature. Let's move on with the actual demo. This is going to be a rather simple demo.I create a simple HTML 5 page. The markup follows and it is very easy to use and understand.This is a page with a 2 column layout. <!DOCTYPE html><html lang="en"> <head> <title>HTML 5, CSS3 and JQuery</title> <meta http-equiv="Content-Type" content="text/html;charset=utf-8" > <link rel="stylesheet" type="text/css" href="style.css"> </head> <body> <div id="header"> <h1>Learn cutting edge technologies</h1> <p>HTML 5, JQuery, CSS3</p> </div> <div id="main"> <div id="mainnews"> <div> <h2>HTML 5</h2> </div> <div> <p> HTML5 is the latest version of HTML and XHTML. The HTML standard defines a single language that can be written in HTML and XML. It attempts to solve issues found in previous iterations of HTML and addresses the needs of Web Applications, an area previously not adequately covered by HTML. </p> <div class="quote"> <h4>Do More with Less</h4> <p> jQuery is a fast and concise JavaScript Library that simplifies HTML document traversing, event handling, animating, and Ajax interactions for rapid web development. </p> </div> <p> The HTML5 test(html5test.com) score is an indication of how well your browser supports the upcoming HTML5 standard and related specifications. Even though the specification isn't finalized yet, all major browser manufacturers are making sure their browser is ready for the future. Find out which parts of HTML5 are already supported by your browser today and compare the results with other browsers. The HTML5 test does not try to test all of the new features offered by HTML5, nor does it try to test the functionality of each feature it does detect. Despite these shortcomings we hope that by quantifying the level of support users and web developers will get an idea of how hard the browser manufacturers work on improving their browsers and the web as a development platform.</p> </div> </div> <div id="CSS"> <div> <h2>CSS 3 Intro</h2> </div> <div> <p> Cascading Style Sheets (CSS) is a style sheet language used for describing the presentation semantics (the look and formatting) of a document written in a markup language. Its most common application is to style web pages written in HTML and XHTML, but the language can also be applied to any kind of XML document, including plain XML, SVG and XUL. </p> </div> </div> <div id="CSSmore"> <div> <h2>CSS 3 Purpose</h2> </div> <div> <p> CSS is designed primarily to enable the separation of document content (written in HTML or a similar markup language) from document presentation, including elements such as the layout, colors, and fonts.[1] This separation can improve content accessibility, provide more flexibility and control in the specification of presentation characteristics, enable multiple pages to share formatting, and reduce complexity and repetition in the structural content (such as by allowing for tableless web design). </p> </div> </div> </div> <div id="footer"> <p>Feel free to google more about the subject</p> </div> </body> </html> The CSS code (style.css) follows body{ line-height: 30px; width: 1024px; background-color:#eee; } p{ font-size:17px; font-family:"Comic Sans MS" } p,h2,h3,h4{ margin: 0 0 20px 0; } #main, #header, #footer{ width: 100%; margin: 0px auto; display:block; } #header{ text-align: center; border-bottom: 1px solid #000; margin-bottom: 30px; } #footer{ text-align: center; border-top: 1px solid #000; margin-bottom: 30px; } .quote{ width: 200px; margin-left: 10px; padding: 5px; float: right; border: 2px solid #000; background-color:#F9ACAE; } .quote :last-child{ margin-bottom: 0; } #main{ column-count:2; column-gap:20px; column-rule: 1px solid #000; -moz-column-count: 2; -webkit-column-count: 2; -moz-column-gap: 20px; -webkit-column-gap: 20px; -moz-column-rule: 1px solid #000; -webkit-column-rule: 1px solid #000; } Now I view the page in the browser.Now I am going to write a media query and add some more rules in the .css file in order to change the layout of the page when the page is viewed by mobile devices. @media only screen and (max-width: 480px) { body{ width: 480px; } #main{ -moz-column-count: 1; -webkit-column-count: 1; } } I am specifying that this media query applies only to screen and a max width of 480 px. If this condition is true, then I add new rules for the body element. I change the number of columns to one. This rule will not be applied unless the maximum width is 480px or less. As I decrease the size-width of the browser window I see no change in the column's layout. Have a look at the picture below. When I resize the window and the width of the browser so the width is less than 480px, the media query and its respective rules take effect.We can scroll vertically to view the content which is a more optimised viewing experience for mobile devices. Have a look at the picture below Hope it helps!!!!

Read the article

.NET Code Evolution

- by Alois Kraus

Originally posted on: http://geekswithblogs.net/akraus1/archive/2013/07/24/153504.aspxAt my day job I do look at a lot of code written by other people. Most of the code is quite good and some is even a masterpiece. And there is also code which makes you think WTF… oh it was written by me. Hm not so bad after all. There are many excuses reasons for bad code. Most often it is time pressure followed by not enough ambition (who cares) or insufficient training. Normally I do care about code quality quite a lot which makes me a (perceived) slow worker who does write many tests and refines the code quite a lot because of the design deficiencies. Most of the deficiencies I do find by putting my design under stress while checking for invariants. It does also help a lot to step into the code with a debugger (sometimes also Windbg). I do this much more often when my tests are red. That way I do get a much better understanding what my code really does and not what I think it should be doing. This time I do want to show you how code can evolve over the years with different .NET Framework versions. Once there was time where .NET 1.1 was new and many C++ programmers did switch over to get rid of not initialized pointers and memory leaks. There were also nice new data structures available such as the Hashtable which is fast lookup table with O(1) time complexity. All was good and much code was written since then. At 2005 a new version of the .NET Framework did arrive which did bring many new things like generics and new data structures. The “old” fashioned way of Hashtable were coming to an end and everyone used the new Dictionary<xx,xx> type instead which was type safe and faster because the object to type conversion (aka boxing) was no longer necessary. I think 95% of all Hashtables and dictionaries use string as key. Often it is convenient to ignore casing to make it easy to look up values which the user did enter. An often followed route is to convert the string to upper case before putting it into the Hashtable. Hashtable Table = new Hashtable(); void Add(string key, string value) { Table.Add(key.ToUpper(), value); } This is valid and working code but it has problems. First we can pass to the Hashtable a custom IEqualityComparer to do the string matching case insensitive. Second we can switch over to the now also old Dictionary type to become a little faster and we can keep the the original keys (not upper cased) in the dictionary. Dictionary<string, string> DictTable = new Dictionary<string, string>(StringComparer.OrdinalIgnoreCase); void AddDict(string key, string value) { DictTable.Add(key, value); } Many people do not user the other ctors of Dictionary because they do shy away from the overhead of writing their own comparer. They do not know that .NET has for strings already predefined comparers at hand which you can directly use. Today in the many core area we do use threads all over the place. Sometimes things break in subtle ways but most of the time it is sufficient to place a lock around the offender. Threading has become so mainstream that it may sound weird that in the year 2000 some guy got a huge incentive for the idea to reduce the time to process calibration data from 12 hours to 6 hours by using two threads on a dual core machine. Threading does make it easy to become faster at the expense of correctness. Correct and scalable multithreading can be arbitrarily hard to achieve depending on the problem you are trying to solve. Lets suppose we want to process millions of items with two threads and count the processed items processed by all threads. A typical beginners code might look like this: int Counter; void IJustLearnedToUseThreads() { var t1 = new Thread(ThreadWorkMethod); t1.Start(); var t2 = new Thread(ThreadWorkMethod); t2.Start(); t1.Join(); t2.Join(); if (Counter != 2 * Increments) throw new Exception("Hmm " + Counter + " != " + 2 * Increments); } const int Increments = 10 * 1000 * 1000; void ThreadWorkMethod() { for (int i = 0; i < Increments; i++) { Counter++; } } It does throw an exception with the message e.g. “Hmm 10.222.287 != 20.000.000” and does never finish. The code does fail because the assumption that Counter++ is an atomic operation is wrong. The ++ operator is just a shortcut for Counter = Counter + 1 This does involve reading the counter from a memory location into the CPU, incrementing value on the CPU and writing the new value back to the memory location. When we do look at the generated assembly code we will see only inc dword ptr [ecx+10h] which is only one instruction. Yes it is one instruction but it is not atomic. All modern CPUs have several layers of caches (L1,L2,L3) which try to hide the fact how slow actual main memory accesses are. Since cache is just another word for redundant copy it can happen that one CPU does read a value from main memory into the cache, modifies it and write it back to the main memory. The problem is that at least the L1 cache is not shared between CPUs so it can happen that one CPU does make changes to values which did change in meantime in the main memory. From the exception you can see we did increment the value 20 million times but half of the changes were lost because we did overwrite the already changed value from the other thread. This is a very common case and people do learn to protect their data with proper locking. void Intermediate() { var time = Stopwatch.StartNew(); Action acc = ThreadWorkMethod_Intermediate; var ar1 = acc.BeginInvoke(null, null); var ar2 = acc.BeginInvoke(null, null); ar1.AsyncWaitHandle.WaitOne(); ar2.AsyncWaitHandle.WaitOne(); if (Counter != 2 * Increments) throw new Exception(String.Format("Hmm {0:N0} != {1:N0}", Counter, 2 * Increments)); Console.WriteLine("Intermediate did take: {0:F1}s", time.Elapsed.TotalSeconds); } void ThreadWorkMethod_Intermediate() { for (int i = 0; i < Increments; i++) { lock (this) { Counter++; } } } This is better and does use the .NET Threadpool to get rid of manual thread management. It does give the expected result but it can result in deadlocks because you do lock on this. This is in general a bad idea since it can lead to deadlocks when other threads use your class instance as lock object. It is therefore recommended to create a private object as lock object to ensure that nobody else can lock your lock object. When you read more about threading you will read about lock free algorithms. They are nice and can improve performance quite a lot but you need to pay close attention to the CLR memory model. It does make quite weak guarantees in general but it can still work because your CPU architecture does give you more invariants than the CLR memory model. For a simple counter there is an easy lock free alternative present with the Interlocked class in .NET. As a general rule you should not try to write lock free algos since most likely you will fail to get it right on all CPU architectures. void Experienced() { var time = Stopwatch.StartNew(); Task t1 = Task.Factory.StartNew(ThreadWorkMethod_Experienced); Task t2 = Task.Factory.StartNew(ThreadWorkMethod_Experienced); t1.Wait(); t2.Wait(); if (Counter != 2 * Increments) throw new Exception(String.Format("Hmm {0:N0} != {1:N0}", Counter, 2 * Increments)); Console.WriteLine("Experienced did take: {0:F1}s", time.Elapsed.TotalSeconds); } void ThreadWorkMethod_Experienced() { for (int i = 0; i < Increments; i++) { Interlocked.Increment(ref Counter); } } Since time does move forward we do not use threads explicitly anymore but the much nicer Task abstraction which was introduced with .NET 4 at 2010. It is educational to look at the generated assembly code. The Interlocked.Increment method must be called which does wondrous things right? Lets see: lock inc dword ptr [eax] The first thing to note that there is no method call at all. Why? Because the JIT compiler does know very well about CPU intrinsic functions. Atomic operations which do lock the memory bus to prevent other processors to read stale values are such things. Second: This is the same increment call prefixed with a lock instruction. The only reason for the existence of the Interlocked class is that the JIT compiler can compile it to the matching CPU intrinsic functions which can not only increment by one but can also do an add, exchange and a combined compare and exchange operation. But be warned that the correct usage of its methods can be tricky. If you try to be clever and look a the generated IL code and try to reason about its efficiency you will fail. Only the generated machine code counts. Is this the best code we can write? Perhaps. It is nice and clean. But can we make it any faster? Lets see how good we are doing currently. Level Time in s IJustLearnedToUseThreads Flawed Code Intermediate 1,5 (lock) Experienced 0,3 (Interlocked.Increment) Master 0,1 (1,0 for int[2]) That lock free thing is really a nice thing. But if you read more about CPU cache, cache coherency, false sharing you can do even better. int[] Counters = new int[12]; // Cache line size is 64 bytes on my machine with an 8 way associative cache try for yourself e.g. 64 on more modern CPUs void Master() { var time = Stopwatch.StartNew(); Task t1 = Task.Factory.StartNew(ThreadWorkMethod_Master, 0); Task t2 = Task.Factory.StartNew(ThreadWorkMethod_Master, Counters.Length - 1); t1.Wait(); t2.Wait(); Counter = Counters[0] + Counters[Counters.Length - 1]; if (Counter != 2 * Increments) throw new Exception(String.Format("Hmm {0:N0} != {1:N0}", Counter, 2 * Increments)); Console.WriteLine("Master did take: {0:F1}s", time.Elapsed.TotalSeconds); } void ThreadWorkMethod_Master(object number) { int index = (int) number; for (int i = 0; i < Increments; i++) { Counters[index]++; } } The key insight here is to use for each core its own value. But if you simply use simply an integer array of two items, one for each core and add the items at the end you will be much slower than the lock free version (factor 3). Each CPU core has its own cache line size which is something in the range of 16-256 bytes. When you do access a value from one location the CPU does not only fetch one value from main memory but a complete cache line (e.g. 16 bytes). This means that you do not pay for the next 15 bytes when you access them. This can lead to dramatic performance improvements and non obvious code which is faster although it does have many more memory reads than another algorithm. So what have we done here? We have started with correct code but it was lacking knowledge how to use the .NET Base Class Libraries optimally. Then we did try to get fancy and used threads for the first time and failed. Our next try was better but it still had non obvious issues (lock object exposed to the outside). Knowledge has increased further and we have found a lock free version of our counter which is a nice and clean way which is a perfectly valid solution. The last example is only here to show you how you can get most out of threading by paying close attention to your used data structures and CPU cache coherency. Although we are working in a virtual execution environment in a high level language with automatic memory management it does pay off to know the details down to the assembly level. Only if you continue to learn and to dig deeper you can come up with solutions no one else was even considering. I have studied particle physics which does help at the digging deeper part. Have you ever tried to solve Quantum Chromodynamics equations? Compared to that the rest must be easy ;-). Although I am no longer working in the Science field I take pride in discovering non obvious things. This can be a very hard to find bug or a new way to restructure data to make something 10 times faster. Now I need to get some sleep ….

Read the article

cannot access localhost using ip

- by Robert

I have done a small web development project using eclipse. It runs well when I try running it on browser with url localhost:8080/myproject/home.html. But if I want to access it on another machine (laptop, mobile, etc. using the same wifi) it is not possible; it is not able to connect. After Googling for a while found out that I have to use the IP address instead of 'localhost'. So I tried 10.0.0.4:8080/myproject/home.html, but still does not work. In fact i am unable to open that url on the same machine (where localhost:8080/myproject/home.html works fine). I also added a new Inbound rule in control panel firewall settings, allowing access to all ports for protocol TCP. Still have problem in running application with the url 10.0.0.4:8080/myproject/home.html (both on same machine as well as laptop and mobile). FYI i am using Eclipse Indigo, Apache tomcat 6.0 and server.xml file contents is as below: <?xml version="1.0" encoding="UTF-8"?> <Server port="8005" shutdown="SHUTDOWN">  <Listener SSLEngine="on" className="org.apache.catalina.core.AprLifecycleListener"/>  <Listener className="org.apache.catalina.core.JasperListener"/>  <Listener className="org.apache.catalina.core.JreMemoryLeakPreventionListener"/>  <Listener className="org.apache.catalina.mbeans.ServerLifecycleListener"/> <Listener className="org.apache.catalina.mbeans.GlobalResourcesLifecycleListener"/>  <GlobalNamingResources>  <Resource auth="Container" description="User database that can be updated and saved" factory="org.apache.catalina.users.MemoryUserDatabaseFactory" name="UserDatabase" pathname="conf/tomcat-users.xml" type="org.apache.catalina.UserDatabase"/> </GlobalNamingResources>  <Service name="Catalina">    <Connector port="8080" protocol="HTTP/1.1" address="10.0.0.4" connectionTimeout="20000" redirectPort="8443" />      <Connector port="8009" protocol="AJP/1.3" redirectPort="8443"/>   <Engine defaultHost="localhost" name="Catalina">      <Realm className="org.apache.catalina.realm.UserDatabaseRealm" resourceName="UserDatabase"/>  <Host appBase="webapps" autoDeploy="true" name="localhost" unpackWARs="true" xmlNamespaceAware="false" xmlValidation="false">     <Context docBase="myproject" path="/myproject" reloadable="true" source="org.eclipse.jst.jee.server:myproject"/></Host> </Engine> </Service> </Server>

Read the article

CodePlex Daily Summary for Saturday, November 03, 2012

CodePlex Daily Summary for Saturday, November 03, 2012Popular ReleasesZXMAK2: Version 2.6.8.2: fix save to SZX snapshot for +3 model fix +3 ULA timingsLaunchbar: Launchbar 4.2.2.0: This release is the first step in cleaning up the code and using all the latest features of .NET 4.5 Changes 4.2.2 (2012-11-02) Improved handling of left clicks 4.1.0 (2012-10-17) Removed tray icon Assembly renamed and signed with strong name Note When you upgrade, Launchbar will start with the default settings. You can import your previous settings by following these steps: Run Launchbar and just save the settings without configuring anything Shutdown Launchbar Go to the folder %LOCA...CommonLibrary.NET: CommonLibrary.NET 0.9.8.8: Releases notes for FluentScript located at http://fluentscript.codeplex.com/wikipage?title=Release%20Notes&referringTitle=Documentation Fluentscript - 0.9.8.8 - Final ReleaseApplication: FluentScript Version: 0.9.8.8 Build: 0.9.8.8 Changeset: 77368 ( CommonLibrary.NET ) Release date: November 2nd, 2012 Binaries: CommonLibrary.dll Namespace: ComLib.Lang Project site: http://fluentscript.codeplex.com/ Download: http://commonlibrarynet.codeplex.com/releases/view/90426 Source code: http://common...Mouse Jiggler: MouseJiggle-1.3: This adds the much-requested minimize-to-tray feature to Mouse Jiggler.Umbraco CMS: Umbraco 4.10.0 Release Candidate: This is a Release Candidate, which means that if we do not find any major issues in the next week, we will release this version as the final release of 4.10.0 on November 9th, 2012. The documentation for the MVC bits still lives in the Github version of the docs for now and will be updated on our.umbraco.org with the final release of 4.10.0. Browse the documentation here: https://github.com/umbraco/Umbraco4Docs/tree/4.8.0/Documentation/Reference/Mvc If you want to do only MVC then make sur...Skype Auto Recorder: SkypeAutoRecorder 1.3.4: New icon and images. Reworked settings window. Implemented high-quality sound encoding. Implemented a possibility to produce stereo records. Added buttons with system-wide hot keys for manual starting and canceling of recording. Added buttons for opening folder with records. Added Help button. Fixed an issue when recording is continuing after call end. Fixed an issue when recording doesn't start. Fixed several bugs and improved stability. Major refactoring and optimization...Access 2010 Application Platform - Build Your Own Database: Application Platform - 0.0.2: Release 0.0.2 Created two new users. One belongs to the Administrators group and the other to the Public group. User: admin Pass: admin User: guest Pass: guest Initial Release This is the first version of the database. At the moment is all contained in one file to make development easier, but the obvious idea would be to split it into Front and Back End for a production version of the tool. The features it contains at the moment are the "Core" features.Python Tools for Visual Studio: Python Tools for Visual Studio 1.5: We’re pleased to announce the release of Python Tools for Visual Studio 1.5 RTM. Python Tools for Visual Studio (PTVS) is an open-source plug-in for Visual Studio which supports programming with the Python language. PTVS supports a broad range of features including CPython/IronPython, Edit/Intellisense/Debug/Profile, Cloud, HPC, IPython, etc. support. For a quick overview of the general IDE experience, please watch this video There are a number of exciting improvement in this release comp...BCF.Net: BCF.Net: BCF.Net-20121024 source codeAssaultCube Reloaded: 2.5.5: Linux has Ubuntu 11.10 32-bit precompiled binaries and Ubuntu 10.10 64-bit precompiled binaries, but you can compile your own as it also contains the source. If you are using Mac or other operating systems, please wait while we try to package for those OSes. Try to compile it. If it fails, download a virtual machine. The server pack is ready for both Windows and Linux, but you might need to compile your own for Linux (source included) Changelog: Fixed potential bot bugs: Map change, OpenAL...Edi: Edi 1.0 with DarkExpression: Added DarkExpression theme (dialogs and message boxes are not completely themed, yet)DirectX Tool Kit: October 30, 2012 (add WP8 support): October 30, 2012 Added project files for Windows Phone 8MCEBuddy 2.x: MCEBuddy 2.3.6: Changelog for 2.3.6 (32bit and 64bit) 1. Fixed a bug in multichannel audio conversion failure. AAC does not support 6 channel audio, MCEBuddy now checks for it and force the output to 2 channel if AAC codec is specified 2. Fixed a bug in Original Broadcast Date and Time. Original Broadcast Date and Time is reported in UTC timezone in WTV metadata. TVDB and MovieDB dates are reported in network timezone. It is assumed the video is recorded and converted on the same machine, i.e. local timezone...MVVM Light Toolkit: MVVM Light Toolkit V4.1 for Visual Studio 2012: This version only supports Visual Studio 2012 (and all Express editions too). If you use Visual Studio 2010, please stay tuned, we will publish an update in a few days with support for VS10. V4.1 supports: Windows Phone 8 Windows 8 (Windows RT) Silverlight 5 Silverlight 4 WPF 4.5 WPF 4 WPF 3.5 And the following development environments: Visual Studio 2012 (Pro, Premium, Ultimate) Visual Studio 2012 Express for Windows 8 Visual Studio 2012 Express for Windows Phone 8 Visual...Microsoft Ajax Minifier: Microsoft Ajax Minifier 4.73: Fix issue in Discussion #401101 (unreferenced var in a for-in statement was getting removed). add the grouping operator to the parsed output so that unminified parsed code is closer to the original. Will still strip unneeded parens later, if minifying. more cleaning of references as they are minified out of the code.RiP-Ripper & PG-Ripper: PG-Ripper 1.4.03: changes NEW: Added Support for the phun.org forum FIXED: Kitty-Kats new Forum UrlLiberty: v3.4.0.1 Release 28th October 2012: Change Log -Fixed -H4 Fixed the save verification screen showing incorrect mission and difficulty information for some saves -H4 Hopefully fixed the issue where progress did not save between missions and saves would not revert correctly -H3 Fixed crashes that occurred when trying to load player information -Proper exception dialogs will now show in place of crashesPlayer Framework by Microsoft: Player Framework for Windows 8 (Preview 7): This release is compatible with the version of the Smooth Streaming SDK released today (10/26). Release 1 of the player framework is expected to be available next week. IMPROVEMENTS & FIXESIMPORTANT: List of breaking changes from preview 6 Support for the latest smooth streaming SDK. Xaml only: Support for moving any of the UI elements outside the MediaPlayer (e.g. into the appbar). Note: Equivelent changes to the JS version due in coming week. Support for localizing all text used in t...Send multiple SMS via Way2SMS C#: SMS 1.1: Added support for 160by2Quick Launch: Quick Launch 1.0: A Lightweight and Fast Way to Manage and Launch Thousands of Tools and ApplicationsPress Win+Q and start to search and run. http://www.codeplex.com/Download?ProjectName=quicklaunch&DownloadId=523536New Projectsappnitiren: This project's main objective is to deepen my knowledge on developing apps for windows 8 and windows phone and Buddhist philosophy of Nichiren Daishonin. Aspect - TypeScript AOP Framework: A simple AOP framework for TypeScript.AWF's PowerPoint Tab: A collection of little powerpoint utilities, including "resize all shapes".Base64 Encoder-Decoder: (Base64 Encoder/Decoder using C#)BombaJob-WF: Official Windows desktop client for BombaJob.bgBungie Test: !CCAudio: A project to create an audio recording/mixing and processing framework in C#/C++ with a look to creating a Digital Audio Workstation. EvaluationSyarem: for yuanguangexporttfschangesets: Small utility that runs agains tftp.exe(tfs power tools) and exports a given range of changesets.fjfdszjtfs: fjfdszjtfsKladionica: Ovo je mala web aplikacija koja je specijalizovana za f1 kladionicu na forumu KrstaricaListViewItem Float Test: WPF testing ground for development of a "floating" listviewitem (preeettty)Macconnell: This is my test projectNWebsec Demo site: This is the NWebsec demo website project.Ocean Flattened: Summary of this projectQuagmire: QUAGMIRE aims to make distributed data processing and visualisation simple and flexible.Scheduled SQL Jobs for DotNetNuke by IowaComputerGurus Inc.: Keeping a DotNetNuke site database clean can be a real nightmare for those hosting sites on shared hosting providers.Secretary Tool: Tool for secretaries of congregations of Jehovah's Witnesses.Secure My Install for DotNetNuke by IowaComputerGurus: This module is a single-use per DotNetNuke installation utility module that will make a number of security enhancing modifications to your "out of the box" DotNServStop: ServStop is a .NET application that makes it easy to stop several system services at once. Now you don't have to change startup types or stop them one at a time. It has a simple list-based interface with the ability to save and load lists of user services to stop. Written in C#.Simple File List for DotNetNuke by IowaComputerGurus Inc.: The Simple File List module is a Free DotNetNuke module that will list all files within a specific folder under the specific portal folder within DNN for users SOLUS3 Config Discovery: An open-source community developed tool for generating a simple text file detailing your local SIMS server settings to simplify new SOLUS3 configurations.Sort Project: Project Name: Sort Project Description: This project holds a class that extends objects type of IEnumerable by enabling them using sorting algorithms other than the buil in one within the microsoft staff SQL Azure Data Protector: This tool leverages the currently available options that Azure platform has to provide an integrated and automated solution to back up the SQL Azure databases.Throttling Suite for ASP.NET Applications: The Throttling Suite provides throttling control capabilities to the ASP.NET applications. It is highly customizable; including "log-only" mode.TidyBackups: Allows for automation of deletion of Microsoft SQL backup files based on file type (.bak) creation age as well as compression using standard ZIP technology.TrainingData: TrainingData is a set of libraries for reading and modifying training data files for Garmin and Polar heart rate monitors.Virtual eCommerce: ??? ? ?????? ????????? ??????. ??????: ??????????? ?????????, ?????????? ?????????? ?? ????????????? ?? Microsoft - ASP Web Pages with Razor Engine.WebNext: My personal web page / blog with cms on asp mvc 3Windows 8 Mouse Unsticky: Makes Windows 8 top right/left hot corners unsticky.WPForms: WPForms is simple framework for Form-driven Silverlight Windows Phone applications. Using the framework allows developers to easily create and display forms.

Read the article

Google and Bing Map APIs Compared

- by SGWellens

At one of the local golf courses I frequent, there is an open grass field next to the course. It is about eight acres in size and mowed regularly. It is permissible to hit golf balls there—you bring and shag our own balls. My golf colleagues and I spend hours there practicing, chatting and in general just wasting time. One of the guys brings Ginger, the amazing, incredible, wonder dog. Ginger is a Portuguese Pointer. She chases squirrels, begs for snacks and supervises us closely to make sure we don't misbehave. Anyway, I decided to make a dedicated web page to measure distances on the field in yards using online mapping services. I started with Google maps and then did the same application with Bing maps. It is a good way to become familiar with the APIs. Here are images of the final two maps: Google: Bing: To start with online mapping services, you need to visit the respective websites and get a developers key. I pared the code down to the minimum to make it easier to compare the APIs. Google maps required this CSS (or it wouldn't work): <style type="text/css"> html { height: 100%; } body { height: 100%; margin: 0; padding: 0; } Here is how the map scripts are included. Google requires the developer Key when loading the JavaScript, Bing requires it when the map object is created: Google: <script type="text/javascript" src="https://maps.googleapis.com/maps/api/js?key=XXXXXXX&libraries=geometry&sensor=false" > </script> Bing: <script type="text/javascript" src="http://ecn.dev.virtualearth.net/mapcontrol/mapcontrol.ashx?v=7.0"> </script> Note: I use jQuery to manipulate the DOM elements which may be overkill, but I may add more stuff to this application and I didn't want to have to add it later. Plus, I really like jQuery. Here is how the maps are created: Common Code (the same for both Google and Bing Maps): <script type="text/javascript"> var gTheMap; var gMarker1; var gMarker2; $(document).ready(DocLoaded); function DocLoaded() { // golf course coordinates var StartLat = 44.924254; var StartLng = -93.366859; // what element to display the map in var mapdiv = $("#map_div")[0]; Google: // where on earth the map should display var StartPoint = new google.maps.LatLng(StartLat, StartLng); // create the map gTheMap = new google.maps.Map(mapdiv, { center: StartPoint, zoom: 18, mapTypeId: google.maps.MapTypeId.SATELLITE }); // place two markers marker1 = PlaceMarker(new google.maps.LatLng(StartLat, StartLng + .0001)); marker2 = PlaceMarker(new google.maps.LatLng(StartLat, StartLng - .0001)); DragEnd(null); } Bing: // where on earth the map should display var StartPoint = new Microsoft.Maps.Location(StartLat, StartLng); // create the map gTheMap = new Microsoft.Maps.Map(mapdiv, { credentials: 'Asbsa_hzfHl69XF3wxBd_WbW0dLNTRUH3ZHQG9qcV5EFRLuWEaOP1hjWdZ0A0P17', center: StartPoint, zoom: 18, mapTypeId: Microsoft.Maps.MapTypeId.aerial }); // place two markers marker1 = PlaceMarker(new Microsoft.Maps.Location(StartLat, StartLng + .0001)); marker2 = PlaceMarker(new Microsoft.Maps.Location(StartLat, StartLng - .0001)); DragEnd(null); } Note: In the Bing documentation, mapTypeId: was missing from the list of options even though the sample code included it. Note: When creating the Bing map, use the developer Key for the credentials property. I immediately place two markers/pins on the map which is simpler that creating them on the fly with mouse clicks (as I first tried). The markers/pins are draggable and I capture the DragEnd event to calculate and display the distance in yards and draw a line when the user finishes dragging. Here is the code to place a marker: Google: // ---- PlaceMarker ------------------------------------ function PlaceMarker(location) { var marker = new google.maps.Marker( { position: location, map: gTheMap, draggable: true }); marker.addListener('dragend', DragEnd); return marker; } Bing: // ---- PlaceMarker ------------------------------------ function PlaceMarker(location) { var marker = new Microsoft.Maps.Pushpin(location, { draggable : true }); Microsoft.Maps.Events.addHandler(marker, 'dragend', DragEnd); gTheMap.entities.push(marker); return marker; } Here is the code than runs when the user stops dragging a marker: Google: // ---- DragEnd ------------------------------------------- var gLine = null; function DragEnd(Event) { var meters = google.maps.geometry.spherical.computeDistanceBetween(marker1.position, marker2.position); var yards = meters * 1.0936133; $("#message").text(yards.toFixed(1) + ' yards'); // draw a line connecting the points var Endpoints = [marker1.position, marker2.position]; if (gLine == null) { gLine = new google.maps.Polyline({ path: Endpoints, strokeColor: "#FFFF00", strokeOpacity: 1.0, strokeWeight: 2, map: gTheMap }); } else gLine.setPath(Endpoints); } Bing: // ---- DragEnd ------------------------------------------- var gLine = null; function DragEnd(Args) { var Distance = CalculateDistance(marker1._location, marker2._location); $("#message").text(Distance.toFixed(1) + ' yards'); // draw a line connecting the points var Endpoints = [marker1._location, marker2._location]; if (gLine == null) { gLine = new Microsoft.Maps.Polyline(Endpoints, { strokeColor: new Microsoft.Maps.Color(0xFF, 0xFF, 0xFF, 0), // aRGB strokeThickness : 2 }); gTheMap.entities.push(gLine); } else gLine.setLocations(Endpoints); } Note: I couldn't find a function to calculate the distance between points in the Bing API, so I wrote my own (CalculateDistance). If you want to see the source for it, you can pick it off the web page. Note: I was able to verify the accuracy of the measurements by using the golf hole next to the field. I put a pin/marker on the center of the green, and then by zooming in, I was able to see the 150 markers on the fairway and put the other pin/marker on one of them. Final Notes: All in all, the APIs are very similar. Both made it easy to accomplish a lot with a minimum amount of code. In one aerial view, there are leaves on the tree, in the other, the trees are bare. I don't know which service has the newer data. Here are links to working pages: Bing Map Demo Google Map Demo I hope someone finds this useful. Steve Wellens CodeProject

Read the article

Google and Bing Map APIs Compared

- by SGWellens

At one of the local golf courses I frequent, there is an open grass field next to the course. It is about eight acres in size and mowed regularly. It is permissible to hit golf balls there—you bring and shag our own balls. My golf colleagues and I spend hours there practicing, chatting and in general just wasting time. One of the guys brings Ginger, the amazing, incredible, wonder dog. Ginger is a Hungarian Vizlas (or Hungarian pointer). She chases squirrels, begs for snacks and supervises us closely to make sure we don't misbehave. Anyway, I decided to make a dedicated web page to measure distances on the field in yards using online mapping services. I started with Google maps and then did the same application with Bing maps. It is a good way to become familiar with the APIs. Here are images of the final two maps: Google: Bing: To start with online mapping services, you need to visit the respective websites and get a developers key. I pared the code down to the minimum to make it easier to compare the APIs. Google maps required this CSS (or it wouldn't work): <style type="text/css"> html { height: 100%; } body { height: 100%; margin: 0; padding: 0; } Here is how the map scripts are included. Google requires the developer Key when loading the JavaScript, Bing requires it when the map object is created: Google: <script type="text/javascript" src="https://maps.googleapis.com/maps/api/js?key=XXXXXXX&libraries=geometry&sensor=false" > </script> Bing: <script type="text/javascript" src="http://ecn.dev.virtualearth.net/mapcontrol/mapcontrol.ashx?v=7.0"> </script> Note: I use jQuery to manipulate the DOM elements which may be overkill, but I may add more stuff to this application and I didn't want to have to add it later. Plus, I really like jQuery. Here is how the maps are created: Common Code (the same for both Google and Bing Maps): <script type="text/javascript"> var gTheMap; var gMarker1; var gMarker2; $(document).ready(DocLoaded); function DocLoaded() { // golf course coordinates var StartLat = 44.924254; var StartLng = -93.366859; // what element to display the map in var mapdiv = $("#map_div")[0]; Google: // where on earth the map should display var StartPoint = new google.maps.LatLng(StartLat, StartLng); // create the map gTheMap = new google.maps.Map(mapdiv, { center: StartPoint, zoom: 18, mapTypeId: google.maps.MapTypeId.SATELLITE }); // place two markers marker1 = PlaceMarker(new google.maps.LatLng(StartLat, StartLng + .0001)); marker2 = PlaceMarker(new google.maps.LatLng(StartLat, StartLng - .0001)); DragEnd(null); } Bing: // where on earth the map should display var StartPoint = new Microsoft.Maps.Location(StartLat, StartLng); // create the map gTheMap = new Microsoft.Maps.Map(mapdiv, { credentials: 'XXXXXXXXXXXXXXXXXXX', center: StartPoint, zoom: 18, mapTypeId: Microsoft.Maps.MapTypeId.aerial }); // place two markers marker1 = PlaceMarker(new Microsoft.Maps.Location(StartLat, StartLng + .0001)); marker2 = PlaceMarker(new Microsoft.Maps.Location(StartLat, StartLng - .0001)); DragEnd(null); } Note: In the Bing documentation, mapTypeId: was missing from the list of options even though the sample code included it. Note: When creating the Bing map, use the developer Key for the credentials property. I immediately place two markers/pins on the map which is simpler that creating them on the fly with mouse clicks (as I first tried). The markers/pins are draggable and I capture the DragEnd event to calculate and display the distance in yards and draw a line when the user finishes dragging. Here is the code to place a marker: Google: // ---- PlaceMarker ------------------------------------ function PlaceMarker(location) { var marker = new google.maps.Marker( { position: location, map: gTheMap, draggable: true }); marker.addListener('dragend', DragEnd); return marker; } Bing: // ---- PlaceMarker ------------------------------------ function PlaceMarker(location) { var marker = new Microsoft.Maps.Pushpin(location, { draggable : true }); Microsoft.Maps.Events.addHandler(marker, 'dragend', DragEnd); gTheMap.entities.push(marker); return marker; } Here is the code than runs when the user stops dragging a marker: Google: // ---- DragEnd ------------------------------------------- var gLine = null; function DragEnd(Event) { var meters = google.maps.geometry.spherical.computeDistanceBetween(marker1.position, marker2.position); var yards = meters * 1.0936133; $("#message").text(yards.toFixed(1) + ' yards'); // draw a line connecting the points var Endpoints = [marker1.position, marker2.position]; if (gLine == null) { gLine = new google.maps.Polyline({ path: Endpoints, strokeColor: "#FFFF00", strokeOpacity: 1.0, strokeWeight: 2, map: gTheMap }); } else gLine.setPath(Endpoints); } Bing: // ---- DragEnd ------------------------------------------- var gLine = null; function DragEnd(Args) { var Distance = CalculateDistance(marker1._location, marker2._location); $("#message").text(Distance.toFixed(1) + ' yards'); // draw a line connecting the points var Endpoints = [marker1._location, marker2._location]; if (gLine == null) { gLine = new Microsoft.Maps.Polyline(Endpoints, { strokeColor: new Microsoft.Maps.Color(0xFF, 0xFF, 0xFF, 0), // aRGB strokeThickness : 2 }); gTheMap.entities.push(gLine); } else gLine.setLocations(Endpoints); } Note: I couldn't find a function to calculate the distance between points in the Bing API, so I wrote my own (CalculateDistance). If you want to see the source for it, you can pick it off the web page. Note: I was able to verify the accuracy of the measurements by using the golf hole next to the field. I put a pin/marker on the center of the green, and then by zooming in, I was able to see the 150 markers on the fairway and put the other pin/marker on one of them. Final Notes: All in all, the APIs are very similar. Both made it easy to accomplish a lot with a minimum amount of code. In one aerial view, there are leaves on the tree, in the other, the trees are bare. I don't know which service has the newer data. Here are links to working pages: Bing Map Demo Google Map Demo I hope someone finds this useful. Steve Wellens CodeProject

Read the article

How do I prevent TCP connection freezes over an OpenVPN network?

- by Jason R

New details added at the end of this question; it's possible that I'm zeroing in on the cause. I have a UDP OpenVPN-based VPN set up in tap mode (I need tap because I need the VPN to pass multicast packets, which doesn't seem to be possible with tun networks) with a handful of clients across the Internet. I've been experiencing frequent TCP connection freezes over the VPN. That is, I will establish a TCP connection (e.g. an SSH connection, but other protocols have similar issues), and at some point during the session, it seems that traffic will cease being transmitted over that TCP session. This seems to be related to points at which large data transfers occur, such as if I execute an ls command in an SSH session, or if I cat a long log file. Some Google searches turn up a number of answers like this previous one on Server Fault, indicating that the likely culprit is an MTU issue: that during periods of high traffic, the VPN is trying to send packets that get dropped somewhere in the pipes between the VPN endpoints. The above-linked answer suggests using the following OpenVPN configuration settings to mitigate the problem: fragment 1400 mssfix This should limit the MTU used on the VPN to 1400 bytes and fix the TCP maximum segment size to prevent the generation of any packets larger than that. This seems to mitigate the problem a bit, but I still frequently see the freezes. I've tried a number of sizes as arguments to the fragment directive: 1200, 1000, 576, all with similar results. I can't think of any strange network topology between the two ends that could trigger such a problem: the VPN server is running on a pfSense machine connected directly to the Internet, and my client is also connected directly to the Internet at another location. One other strange piece of the puzzle: if I run the tracepath utility, then that seems to band-aid the problem. A sample run looks like: [~]$ tracepath -n 192.168.100.91 1: 192.168.100.90 0.039ms pmtu 1500 1: 192.168.100.91 40.823ms reached 1: 192.168.100.91 19.846ms reached Resume: pmtu 1500 hops 1 back 64 The above run is between two clients on the VPN: I initiated the trace from 192.168.100.90 to the destination of 192.168.100.91. Both clients were configured with fragment 1200; mssfix; in an attempt to limit the MTU used on the link. The above results would seem to suggest that tracepath was able to detect a path MTU of 1500 bytes between the two clients. I would assume that it would be somewhat smaller due to the fragmentation settings specified in the OpenVPN configuration. I found that result somewhat strange. Even stranger, however: if I have a TCP connection in the stalled state (e.g. an SSH session with a directory listing that froze in the middle), then executing the tracepath command shown above causes the connection to start up again! I can't figure out any reasonable explanation for why this would be the case, but I feel like this might be pointing toward a solution to ultimately eradicate the problem. Does anyone have any recommendations for other things to try? Edit: I've come back and looked at this a bit further, and have found only more confounding information: I set the OpenVPN connection to fragment at 1400 bytes, as shown above. Then, I connected to the VPN from across the Internet and used Wireshark to look at the UDP packets that were sent to the VPN server while the stall occurred. None were greater than the specified 1400 byte count, so the fragmentation seems to be functioning properly. To verify that even a 1400-byte MTU would be sufficient, I pinged the VPN server using the following (Linux) command: ping <host> -s 1450 -M do This (I believe) sends a 1450-byte packet with fragmentation disabled (I at least verified that it didn't work if I set it to an obviously-too-large value like 1600 bytes). These seem to work just fine; I get replies back from the host with no issue. So, maybe this isn't an MTU issue at all. I'm just confused as to what else it might be! Edit 2: The rabbit hole just keeps getting deeper: I've now isolated the problem a bit more. It seems to be related to the exact OS that the VPN client uses. I have successfully duplicated the problem on at least three Ubuntu machines (versions 12.04 through 13.04). I can reliably duplicate an SSH connection freeze within a minute or so by just cat-ing a large log file. However, if I do the same test using a CentOS 6 machine as a client, then I don't see the problem! I've tested using the exact same OpenVPN client version as I was using on the Ubuntu machines. I can cat log files for hours without seeing the connection freeze. This seems to provide some insight as to the ultimate cause, but I'm just not sure what that insight is. I have examined the traffic over the VPN using Wireshark. I'm not a TCP expert, so I'm not sure what to make of the gory details, but the gist is that at some point, a UDP packet gets dropped due to the limited bandwidth of the Internet link, causing TCP retransmissions inside the VPN tunnel. On the CentOS client, these retransmissions occur properly and things move on happily. At some point with the Ubuntu clients, though, the remote end starts retransmitting the same TCP segment over and over (with the transmit delay increasing between each retransmission). The client sends what looks like a valid TCP ACK to each retransmission, but the remote end still continues to transmit the same TCP segment periodically. This extends ad infinitum and the connection stalls. My question here would be: Does anyone have any recommendations for how to troubleshoot and/or determine the root cause of the TCP issue? It's as if the remote end isn't accepting the ACK messages sent by the VPN client. One common difference between the CentOS node and the various Ubuntu releases is that Ubuntu has a much more recent Linux kernel version (from 3.2 in Ubuntu 12.04 to 3.8 in 13.04). A pointer to some new kernel bug maybe? I'm assuming that if that were so, then I wouldn't be the only one experiencing the problem; I don't think this seems like a particularly exotic setup.

Read the article

"Can't Connect to Server" from 2nd virtual host on VPS

- by chaoskreator

I'm using Debian 7 Wheezy and Apache 2.2.22, and I'm setting up Virtual Hosts for a number of websites on my VPS. I've successfully configured the VirtualHost directives for one of the sites, but the second one continually gives "Problem Loading Page" in Firefox. I've run configtest and it has verified all my syntax is correct, and I've checked all the permissions. Everything on the 2nd domain is pretty much copy/pasted from the first, so I'm not sure what the issue is, as there are no entries into /var/log/apache2/error.log other than where I have reloaded the configurations: /# cat /var/log/apache2/error.log [Thu May 29 01:19:00 2014] [notice] Graceful restart requested, doing restart [Thu May 29 01:19:00 2014] [info] Init: Seeding PRNG with 656 bytes of entropy [Thu May 29 01:19:00 2014] [info] Init: Generating temporary RSA private keys (512/1024 bits) [Thu May 29 01:19:00 2014] [info] Init: Generating temporary DH parameters (512/1024 bits) [Thu May 29 01:19:00 2014] [debug] ssl_scache_shmcb.c(253): shmcb_init allocated 512000 bytes of shared memory [Thu May 29 01:19:00 2014] [debug] ssl_scache_shmcb.c(272): for 511920 bytes (512000 including header), recommending 32 subcaches, 133 indexes each [Thu May 29 01:19:00 2014] [debug] ssl_scache_shmcb.c(306): shmcb_init_memory choices follow [Thu May 29 01:19:00 2014] [debug] ssl_scache_shmcb.c(308): subcache_num = 32 [Thu May 29 01:19:00 2014] [debug] ssl_scache_shmcb.c(310): subcache_size = 15992 [Thu May 29 01:19:00 2014] [debug] ssl_scache_shmcb.c(312): subcache_data_offset = 3208 [Thu May 29 01:19:00 2014] [debug] ssl_scache_shmcb.c(314): subcache_data_size = 12784 [Thu May 29 01:19:00 2014] [debug] ssl_scache_shmcb.c(316): index_num = 133 [Thu May 29 01:19:00 2014] [info] Shared memory session cache initialised [Thu May 29 01:19:00 2014] [info] Init: Initializing (virtual) servers for SSL [Thu May 29 01:19:00 2014] [info] mod_ssl/2.2.22 compiled against Server: Apache/2.2.22, Library: OpenSSL/1.0.1e [Thu May 29 01:19:00 2014] [notice] Apache/2.2.22 (Debian) PHP/5.4.4-14+deb7u9 mod_ssl/2.2.22 OpenSSL/1.0.1e mod_perl/2.0.7 Perl/v5.14.2 configured -- resuming normal operations [Thu May 29 01:19:00 2014] [info] Server built: Mar 4 2013 22:05:16 [Thu May 29 01:19:00 2014] [debug] prefork.c(1023): AcceptMutex: sysvsem (default: sysvsem) I've ensured to enable each vhost with a2ensite {sitename.conf} with no errors there, either. Below are the contents of the configuration files... /etc/apache2/apache2.conf # Global configuration # LockFile ${APACHE_LOCK_DIR}/accept.lock PidFile ${APACHE_PID_FILE} Timeout 300 KeepAlive On MaxKeepAliveRequests 100 KeepAliveTimeout 5 ## ## Server-Pool Size Regulation (MPM specific) ## # prefork MPM # StartServers: number of server processes to start # MinSpareServers: minimum number of server processes which are kept spare # MaxSpareServers: maximum number of server processes which are kept spare # MaxClients: maximum number of server processes allowed to start # MaxRequestsPerChild: maximum number of requests a server process serves <IfModule mpm_prefork_module> StartServers 5 MinSpareServers 5 MaxSpareServers 10 MaxClients 150 MaxRequestsPerChild 0 </IfModule> # worker MPM # StartServers: initial number of server processes to start # MinSpareThreads: minimum number of worker threads which are kept spare # MaxSpareThreads: maximum number of worker threads which are kept spare # ThreadLimit: ThreadsPerChild can be changed to this maximum value during a # graceful restart. ThreadLimit can only be changed by stopping # and starting Apache. # ThreadsPerChild: constant number of worker threads in each server process # MaxClients: maximum number of simultaneous client connections # MaxRequestsPerChild: maximum number of requests a server process serves <IfModule mpm_worker_module> StartServers 2 MinSpareThreads 25 MaxSpareThreads 75 ThreadLimit 64 ThreadsPerChild 25 MaxClients 150 MaxRequestsPerChild 0 </IfModule> # event MPM # StartServers: initial number of server processes to start # MinSpareThreads: minimum number of worker threads which are kept spare # MaxSpareThreads: maximum number of worker threads which are kept spare # ThreadsPerChild: constant number of worker threads in each server process # MaxClients: maximum number of simultaneous client connections # MaxRequestsPerChild: maximum number of requests a server process serves <IfModule mpm_event_module> StartServers 2 MinSpareThreads 25 MaxSpareThreads 75 ThreadLimit 64 ThreadsPerChild 25 MaxClients 150 MaxRequestsPerChild 0 </IfModule> # These need to be set in /etc/apache2/envvars User ${APACHE_RUN_USER} Group ${APACHE_RUN_GROUP} # # AccessFileName: The name of the file to look for in each directory # for additional configuration directives. See also the AllowOverride # directive. # AccessFileName .htaccess # # The following lines prevent .htaccess and .htpasswd files from being # viewed by Web clients. # <Files ~ "^\.ht"> Order allow,deny Deny from all Satisfy all </Files> DefaultType None HostnameLookups Off ErrorLog ${APACHE_LOG_DIR}/error.log LogLevel debug # Include module configuration: Include mods-enabled/*.load Include mods-enabled/*.conf # Include list of ports to listen on and which to use for name based vhosts Include ports.conf # # The following directives define some format nicknames for use with # a CustomLog directive (see below). # If you are behind a reverse proxy, you might want to change %h into %{X-Forwarded-For}i # # LogFormat "%v:%p %h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\"" vhost_combined LogFormat "%h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %O" common LogFormat "%{Referer}i -> %U" referer LogFormat "%{User-agent}i" agent <Directory "/var/www"> Order allow,deny Allow from all Require all granted </Directory> # Include generic snippets of statements Include conf.d/ # Include the virtual host configurations: Include sites-enabled/*.conf NameVirtualHost *:80 /etc/apache2/sites-available/site1.net.conf <VirtualHost *:80> ServerName site1.net ServerAlias site1.net *.site1.net DocumentRoot "/var/www/site1" ErrorLog "/var/www/site1/logs/error.log" CustomLog "/var/www/site1/logs/access.log" vhost_combined <Directory "/var/www/site1"> Options None AllowOverride All Order allow,deny Allow from all Satisfy Any </Directory> </VirtualHost> /etc/apache2/sites-available/site2.com.conf <VirtualHost *:80> ServerName site2.com ServerAlias site2.com *.site2.com DocumentRoot "/var/www/site2" ErrorLog "/var/www/site2/logs/error.log" CustomLog "/var/www/site2/logs/access.log" vhost_combined <Directory "/var/www/site2"> Options None AllowOverride All Order allow,deny Allow from all Satisfy Any </Directory> </VirtualHost> I've also tried setting NameVirtualHost like: Listen 80 NameVirtualHost 23.88.121.82:80 NameVirtualHost 127.0.0.1:80 and the VirtualHost Directives: <VirtualHost 23.88.121.82:80> ... </VirtualHost> for both sites, but that causes the first site to fail, as well. I'm wondering if I need to set up individual IPs for each site, possibly? I have 2 more IPv4 and 3 IPv6 addresses available, if that would make a difference. Also, in the grand scheme of things, I will need to enable SSL for the first site. I've been reading that I'll need to basically just mimic the directives for listening on port 80, only on port 443, and make sure mod_ssl is enabled? EDIT: I just ran apache2 -t to test the config files that way, and got the error: apache2: bad user name ${APACHE_RUN_USER}. However, apachectl configtest returns Syntax OK. There are no other mentions of errors with the mutex anywhere else, however. I was pretty sure if there was an error with the user apache was supposed to run under, the server wouldn't start at all... EDIT 2: Restarting apache fixed the bad user name error.

Read the article

java.lang.ClassCastException: java.lang.Integer cannot be cast to java.util.HashMap

- by kongkea

I've got this Error When I click listview to show full image size. how can i solve it? Error 11-20 10:27:47.039: D/AndroidRuntime(5078): Shutting down VM 11-20 10:27:47.039: W/dalvikvm(5078): threadid=1: thread exiting with uncaught exception (group=0x40c061f8) 11-20 10:27:47.047: E/AndroidRuntime(5078): FATAL EXCEPTION: main 11-20 10:27:47.047: E/AndroidRuntime(5078): java.lang.ClassCastException: java.lang.Integer cannot be cast to java.util.HashMap 11-20 10:27:47.047: E/AndroidRuntime(5078): at com.example.mylistview.MainActivity$1.onItemClick(MainActivity.java:103) 11-20 10:27:47.047: E/AndroidRuntime(5078): at android.widget.AdapterView.performItemClick(AdapterView.java:292) 11-20 10:27:47.047: E/AndroidRuntime(5078): at android.widget.AbsListView.performItemClick(AbsListView.java:1173) 11-20 10:27:47.047: E/AndroidRuntime(5078): at android.widget.AbsListView$PerformClick.run(AbsListView.java:2701) 11-20 10:27:47.047: E/AndroidRuntime(5078): at android.widget.AbsListView$1.run(AbsListView.java:3453) 11-20 10:27:47.047: E/AndroidRuntime(5078): at android.os.Handler.handleCallback(Handler.java:605) 11-20 10:27:47.047: E/AndroidRuntime(5078): at android.os.Handler.dispatchMessage(Handler.java:92) 11-20 10:27:47.047: E/AndroidRuntime(5078): at android.os.Looper.loop(Looper.java:137) 11-20 10:27:47.047: E/AndroidRuntime(5078): at android.app.ActivityThread.main(ActivityThread.java:4514) 11-20 10:27:47.047: E/AndroidRuntime(5078): at java.lang.reflect.Method.invokeNative(Native Method) 11-20 10:27:47.047: E/AndroidRuntime(5078): at java.lang.reflect.Method.invoke(Method.java:511) 11-20 10:27:47.047: E/AndroidRuntime(5078): at com.android.internal.os.ZygoteInit$MethodAndArgsCaller.run(ZygoteInit.java:790) 11-20 10:27:47.047: E/AndroidRuntime(5078): at com.android.internal.os.ZygoteInit.main(ZygoteInit.java:557) 11-20 10:27:47.047: E/AndroidRuntime(5078): at dalvik.system.NativeStart.main(Native Method) MainActivity public class MainActivity extends Activity { public static final int DIALOG_DOWNLOAD_JSON_PROGRESS = 0; private ProgressDialog mProgressDialog; ArrayList<HashMap<String, Object>> MyArrList; @SuppressLint("NewApi") @Override public void onCreate(Bundle savedInstanceState) { super.onCreate(savedInstanceState); setContentView(R.layout.activity_main); // Permission StrictMode if (android.os.Build.VERSION.SDK_INT > 9) { StrictMode.ThreadPolicy policy = new StrictMode.ThreadPolicy.Builder().permitAll().build(); StrictMode.setThreadPolicy(policy); } // Download JSON File new DownloadJSONFileAsync().execute(); } @Override protected Dialog onCreateDialog(int id) { switch (id) { case DIALOG_DOWNLOAD_JSON_PROGRESS: mProgressDialog = new ProgressDialog(this); mProgressDialog.setMessage("Downloading....."); mProgressDialog.setProgressStyle(ProgressDialog.STYLE_SPINNER); mProgressDialog.setCancelable(true); mProgressDialog.show(); return mProgressDialog; default: return null; } } // Show All Content public void ShowAllContent() { // listView1 final ListView lstView1 = (ListView)findViewById(R.id.listView1); lstView1.setAdapter(new ImageAdapter(MainActivity.this,MyArrList)); lstView1.setOnItemClickListener(new OnItemClickListener() { @Override public void onItemClick(AdapterView<?> parent, View v, int position, long id) { HashMap<String, Object> hm = (HashMap<String, Object>) lstView1.getAdapter().getItem(position); String imagePath = (String) hm.get("photo"); Intent i = new Intent(MainActivity.this,FullImageActivity.class); i.putExtra("fullImage", imagePath); startActivity(i); } }); } public class ImageAdapter extends BaseAdapter { private Context context; private ArrayList<HashMap<String, Object>> MyArr = new ArrayList<HashMap<String, Object>>(); public ImageAdapter(Context c, ArrayList<HashMap<String, Object>> myArrList) { // TODO Auto-generated method stub context = c; MyArr = myArrList; } public int getCount() { // TODO Auto-generated method stub return MyArr.size(); } public Object getItem(int position) { // TODO Auto-generated method stub return position; } public long getItemId(int position) { // TODO Auto-generated method stub return position; } public View getView(int position, View convertView, ViewGroup parent) { // TODO Auto-generated method stub LayoutInflater inflater = (LayoutInflater) context .getSystemService(Context.LAYOUT_INFLATER_SERVICE); if (convertView == null) { convertView = inflater.inflate(R.layout.activity_column, null); } // ColImage ImageView imageView = (ImageView) convertView.findViewById(R.id.ColImgPath); imageView.getLayoutParams().height = 80; imageView.getLayoutParams().width = 80; imageView.setPadding(5, 5, 5, 5); imageView.setScaleType(ImageView.ScaleType.CENTER_CROP); try { imageView.setImageBitmap((Bitmap)MyArr.get(position).get("ImageThumBitmap")); } catch (Exception e) { // When Error imageView.setImageResource(android.R.drawable.ic_menu_report_image); } // ColImgID TextView txtImgID = (TextView) convertView.findViewById(R.id.ColImgID); txtImgID.setPadding(10, 0, 0, 0); txtImgID.setText("ID : " + MyArr.get(position).get("id").toString()); // ColImgName TextView txtPicName = (TextView) convertView.findViewById(R.id.ColImgName); txtPicName.setPadding(50, 0, 0, 0); txtPicName.setText("Name : " + MyArr.get(position).get("first_name").toString()); return convertView; } } // Download JSON in Background public class DownloadJSONFileAsync extends AsyncTask<String, Void, Void> { protected void onPreExecute() { super.onPreExecute(); showDialog(DIALOG_DOWNLOAD_JSON_PROGRESS); } @Override protected Void doInBackground(String... params) { // TODO Auto-generated method stub String url = "http://192.168.10.104/adchara1/"; JSONArray data; try { data = new JSONArray(getJSONUrl(url)); MyArrList = new ArrayList<HashMap<String, Object>>(); HashMap<String, Object> map; for(int i = 0; i < data.length(); i++){ JSONObject c = data.getJSONObject(i); map = new HashMap<String, Object>(); map.put("id", (String)c.getString("id")); map.put("first_name", (String)c.getString("first_name")); // Thumbnail Get ImageBitmap To Object map.put("photo", (String)c.getString("photo")); map.put("ImageThumBitmap", (Bitmap)loadBitmap(c.getString("photo"))); // Full (for View Popup) map.put("frame", (String)c.getString("frame")); MyArrList.add(map); } } catch (JSONException e) { // TODO Auto-generated catch block e.printStackTrace(); } return null; } protected void onPostExecute(Void unused) { ShowAllContent(); // When Finish Show Content dismissDialog(DIALOG_DOWNLOAD_JSON_PROGRESS); removeDialog(DIALOG_DOWNLOAD_JSON_PROGRESS); } } /*** Get JSON Code from URL ***/ public String getJSONUrl(String url) { StringBuilder str = new StringBuilder(); HttpClient client = new DefaultHttpClient(); HttpGet httpGet = new HttpGet(url); try { HttpResponse response = client.execute(httpGet); StatusLine statusLine = response.getStatusLine(); int statusCode = statusLine.getStatusCode(); if (statusCode == 200) { // Download OK HttpEntity entity = response.getEntity(); InputStream content = entity.getContent(); BufferedReader reader = new BufferedReader(new InputStreamReader(content)); String line; while ((line = reader.readLine()) != null) { str.append(line); } } else { Log.e("Log", "Failed to download file.."); } } catch (ClientProtocolException e) { e.printStackTrace(); } catch (IOException e) { e.printStackTrace(); } return str.toString(); } /***** Get Image Resource from URL (Start) *****/ private static final String TAG = "Image"; private static final int IO_BUFFER_SIZE = 4 * 1024; public static Bitmap loadBitmap(String url) { Bitmap bitmap = null; InputStream in = null; BufferedOutputStream out = null; try { in = new BufferedInputStream(new URL(url).openStream(), IO_BUFFER_SIZE); final ByteArrayOutputStream dataStream = new ByteArrayOutputStream(); out = new BufferedOutputStream(dataStream, IO_BUFFER_SIZE); copy(in, out); out.flush(); final byte[] data = dataStream.toByteArray(); BitmapFactory.Options options = new BitmapFactory.Options(); //options.inSampleSize = 1; bitmap = BitmapFactory.decodeByteArray(data, 0, data.length,options); } catch (IOException e) { Log.e(TAG, "Could not load Bitmap from: " + url); } finally { closeStream(in); closeStream(out); } return bitmap; } private static void closeStream(Closeable stream) { if (stream != null) { try { stream.close(); } catch (IOException e) { android.util.Log.e(TAG, "Could not close stream", e); } } } private static void copy(InputStream in, OutputStream out) throws IOException { byte[] b = new byte[IO_BUFFER_SIZE]; int read; while ((read = in.read(b)) != -1) { out.write(b, 0, read); } } /***** Get Image Resource from URL (End) *****/ @Override public boolean onCreateOptionsMenu(Menu menu) { getMenuInflater().inflate(R.menu.activity_main, menu); return true; } } FullImageActivity String imagePath = getIntent().getStringExtra("fullImage"); if(imagePath != null && !imagePath.isEmpty()){ File imageFile = new File(imagePath); if(imageFile.exists()){ Bitmap myBitmap = BitmapFactory.decodeFile(imageFile.getAbsolutePath()); ImageView iv = (ImageView) findViewById(R.id.fullimage); iv.setImageBitmap(myBitmap); } }

Read the article

Java JTextPane JScrollPane Display Issue

- by ikurtz

The following class implements a chatGUI. When it runs okay the screen looks like this: Fine ChatGUI The problem is very often when i enter text of large length ie. 50 - 100 chars the gui goes crazy. the chat history box shrinks as shown in this image. Any ideas regarding what is causing this? Thank you. package Sartre.Connect4; import javax.swing.*; import java.net.*; import java.awt.*; import java.awt.event.*; import javax.swing.text.StyledDocument; import javax.swing.text.Style; import javax.swing.text.StyleConstants; import javax.swing.text.BadLocationException; import java.io.BufferedOutputStream; import javax.swing.text.html.HTMLEditorKit; import java.io.FileOutputStream; import java.io.IOException; import java.io.FileNotFoundException; import javax.swing.filechooser.FileNameExtensionFilter; import javax.swing.JFileChooser; /** * Chat form class * @author iAmjad */ public class ChatGUI extends JDialog implements ActionListener { /** * Used to hold chat history data */ private JTextPane textPaneHistory = new JTextPane(); /** * provides scrolling to chat history pane */ private JScrollPane scrollPaneHistory = new JScrollPane(textPaneHistory); /** * used to input local message to chat history */ private JTextPane textPaneHome = new JTextPane(); /** * Provides scrolling to local chat pane */ private JScrollPane scrollPaneHomeText = new JScrollPane(textPaneHome); /** * JLabel acting as a statusbar */ private JLabel statusBar = new JLabel("Ready"); /** * Button to clear chat history pane */ private JButton JBClear = new JButton("Clear"); /** * Button to save chat history pane */ private JButton JBSave = new JButton("Save"); /** * Holds contentPane */ private Container containerPane; /** * Layout GridBagLayout manager */ private GridBagLayout gridBagLayout = new GridBagLayout(); /** * GridBagConstraints */ private GridBagConstraints constraints = new GridBagConstraints(); /** * Constructor for ChatGUI */ public ChatGUI(){ setTitle("Chat"); // set up dialog icon URL url = getClass().getResource("Resources/SartreIcon.jpg"); ImageIcon imageIcon = new ImageIcon(url); Image image = imageIcon.getImage(); this.setIconImage(image); this.setAlwaysOnTop(true); setLocationRelativeTo(this.getParent()); //////////////// End icon and placement ///////////////////////// // Get pane and set layout manager containerPane = getContentPane(); containerPane.setLayout(gridBagLayout); ///////////////////////////////////////////////////////////// //////////////// Begin Chat History ////////////////////////////// textPaneHistory.setToolTipText("Chat History Window"); textPaneHistory.setEditable(false); textPaneHistory.setPreferredSize(new Dimension(350,250)); scrollPaneHistory.setVerticalScrollBarPolicy(ScrollPaneConstants.VERTICAL_SCROLLBAR_ALWAYS); scrollPaneHistory.setHorizontalScrollBarPolicy(ScrollPaneConstants.HORIZONTAL_SCROLLBAR_NEVER); // fill Chat History GridBagConstraints constraints.gridx = 0; constraints.gridy = 0; constraints.gridwidth = 10; constraints.gridheight = 10; constraints.weightx = 100; constraints.weighty = 100; constraints.fill = GridBagConstraints.BOTH; constraints.anchor = GridBagConstraints.CENTER; constraints.insets = new Insets(10,10,10,10); constraints.ipadx = 0; constraints.ipady = 0; gridBagLayout.setConstraints(scrollPaneHistory, constraints); // add to the pane containerPane.add(scrollPaneHistory); /////////////////////////////// End Chat History /////////////////////// ///////////////////////// Begin Home Chat ////////////////////////////// textPaneHome.setToolTipText("Home Chat Message Window"); textPaneHome.setPreferredSize(new Dimension(200,50)); textPaneHome.addKeyListener(new MyKeyAdapter()); scrollPaneHomeText.setVerticalScrollBarPolicy(ScrollPaneConstants.VERTICAL_SCROLLBAR_ALWAYS); scrollPaneHomeText.setHorizontalScrollBarPolicy(ScrollPaneConstants.HORIZONTAL_SCROLLBAR_NEVER); // fill Chat History GridBagConstraints constraints.gridx = 0; constraints.gridy = 10; constraints.gridwidth = 6; constraints.gridheight = 1; constraints.weightx = 100; constraints.weighty = 100; constraints.fill = GridBagConstraints.BOTH; constraints.anchor = GridBagConstraints.CENTER; constraints.insets = new Insets(10,10,10,10); constraints.ipadx = 0; constraints.ipady = 0; gridBagLayout.setConstraints(scrollPaneHomeText, constraints); // add to the pane containerPane.add(scrollPaneHomeText); ////////////////////////// End Home Chat ///////////////////////// ///////////////////////Begin Clear Chat History //////////////////////// JBClear.setToolTipText("Clear Chat History"); // fill Chat History GridBagConstraints constraints.gridx = 6; constraints.gridy = 10; constraints.gridwidth = 2; constraints.gridheight = 1; constraints.weightx = 100; constraints.weighty = 100; constraints.fill = GridBagConstraints.BOTH; constraints.anchor = GridBagConstraints.CENTER; constraints.insets = new Insets(10,10,10,10); constraints.ipadx = 0; constraints.ipady = 0; gridBagLayout.setConstraints(JBClear, constraints); JBClear.addActionListener(this); // add to the pane containerPane.add(JBClear); ///////////////// End Clear Chat History //////////////////////// /////////////// Begin Save Chat History ////////////////////////// JBSave.setToolTipText("Save Chat History"); constraints.gridx = 8; constraints.gridy = 10; constraints.gridwidth = 2; constraints.gridheight = 1; constraints.weightx = 100; constraints.weighty = 100; constraints.fill = GridBagConstraints.BOTH; constraints.anchor = GridBagConstraints.CENTER; constraints.insets = new Insets(10,10,10,10); constraints.ipadx = 0; constraints.ipady = 0; gridBagLayout.setConstraints(JBSave, constraints); JBSave.addActionListener(this); // add to the pane containerPane.add(JBSave); ///////////////////// End Save Chat History ///////////////////// /////////////////// Begin Status Bar ///////////////////////////// constraints.gridx = 0; constraints.gridy = 11; constraints.gridwidth = 10; constraints.gridheight = 1; constraints.weightx = 100; constraints.weighty = 50; constraints.fill = GridBagConstraints.BOTH; constraints.anchor = GridBagConstraints.CENTER; constraints.insets = new Insets(0,10,5,0); constraints.ipadx = 0; constraints.ipady = 0; gridBagLayout.setConstraints(statusBar, constraints); // add to the pane containerPane.add(statusBar); ////////////// End Status Bar //////////////////////////// // set resizable to false this.setResizable(false); // pack the GUI pack(); } /** * Deals with necessary menu click events * @param event */ public void actionPerformed(ActionEvent event) { Object source = event.getSource(); // Process Clear button event if (source == JBClear){ textPaneHistory.setText(null); statusBar.setText("Chat History Cleared"); } // Process Save button event if (source == JBSave){ // process only if there is data in history pane if (textPaneHistory.getText().length() > 0){ // process location where to save the chat history file JFileChooser chooser = new JFileChooser(); chooser.setMultiSelectionEnabled(false); chooser.setAcceptAllFileFilterUsed(false); FileNameExtensionFilter filter = new FileNameExtensionFilter("HTML Documents", "htm", "html"); chooser.setFileFilter(filter); int option = chooser.showSaveDialog(ChatGUI.this); if (option == JFileChooser.APPROVE_OPTION) { // Set up document to be parsed as HTML StyledDocument doc = (StyledDocument)textPaneHistory.getDocument(); HTMLEditorKit kit = new HTMLEditorKit(); BufferedOutputStream out; try { // add final file name and extension String filePath = chooser.getSelectedFile().getAbsoluteFile() + ".html"; out = new BufferedOutputStream(new FileOutputStream(filePath)); // write out the HTML document kit.write(out, doc, doc.getStartPosition().getOffset(), doc.getLength()); } catch (FileNotFoundException e) { JOptionPane.showMessageDialog(ChatGUI.this, "Application will now close. \n A restart may cure the error!\n\n" + e.getMessage(), "Fatal Error", JOptionPane.WARNING_MESSAGE, null); System.exit(2); } catch (IOException e){ JOptionPane.showMessageDialog(ChatGUI.this, "Application will now close. \n A restart may cure the error!\n\n" + e.getMessage(), "Fatal Error", JOptionPane.WARNING_MESSAGE, null); System.exit(3); } catch (BadLocationException e){ JOptionPane.showMessageDialog(ChatGUI.this, "Application will now close. \n A restart may cure the error!\n\n" + e.getMessage(), "Fatal Error", JOptionPane.WARNING_MESSAGE, null); System.exit(4); } statusBar.setText("Chat History Saved"); } } } } /** * Process return key for sending the message */ private class MyKeyAdapter extends KeyAdapter { @Override @SuppressWarnings("static-access") public void keyPressed(KeyEvent ke) { DateTime dateTime = new DateTime(); String nowdateTime = dateTime.getDateTime(); int kc = ke.getKeyCode(); if (kc == ke.VK_ENTER) { try { // Process only if there is data if (textPaneHome.getText().length() > 0){ // Add message origin formatting StyledDocument doc = (StyledDocument)textPaneHistory.getDocument(); Style style = doc.addStyle("HomeStyle", null); StyleConstants.setBold(style, true); String home = "Home [" + nowdateTime + "]: "; doc.insertString(doc.getLength(), home, style); StyleConstants.setBold(style, false); doc.insertString(doc.getLength(), textPaneHome.getText() + "\n", style); // update caret location textPaneHistory.setCaretPosition(doc.getLength()); textPaneHome.setText(null); statusBar.setText("Message Sent"); } } catch (BadLocationException e) { JOptionPane.showMessageDialog(ChatGUI.this, "Application will now close. \n A restart may cure the error!\n\n" + e.getMessage(), "Fatal Error", JOptionPane.WARNING_MESSAGE, null); System.exit(1); } ke.consume(); } } } }

Read the article

Netbeans / persistence API error

- by Danny

I am following this tutorial, I'm using netbeans 6.5.1 http://www.netbeans.org/kb/docs/java/gui-db-custom.html When I get to the part where I create the "new entity class from database", which is in the "Customizing the Master/Detail View" section of the tutoiral. I can't ever compile because I get this error in the task list (and I get a runtime error when I run)... Atleast I think these two are related. Error Named queries can be defined only on an Entity or MappedSuperclass class. Countries.java 27 C:/Users/Danny/dev/NetBeansProjects/Test/src/test Error Named queries can be defined only on an Entity or MappedSuperclass class. Products.java 28 C:/Users/Danny/dev/NetBeansProjects/Test/src/test note that all I do is do newentity classes from database, and do exactly as the tutorial says. I stopped on the tutoral at the "Adding Dialog Boxes" heading, because the tutorial writer says the application should be "partially functional" which makes me think it should atleast RUN. I haven't edited the generated code outside of what I've been instructed to do. This is the output produced by the netbeans output console: run: Jun 23, 2009 3:03:23 PM org.jdesktop.application.Application$1 run SEVERE: Application class test.TestApp failed to launch javax.persistence.PersistenceException: No Persistence provider for EntityManager named MyBusinessRecordsPU: Provider named oracle.toplink.essentials.PersistenceProvider threw unexpected exception at create EntityManagerFactory: oracle.toplink.essentials.exceptions.PersistenceUnitLoadingException Local Exception Stack: Exception [TOPLINK-30005] (Oracle TopLink Essentials - 2.0.1 (Build b09d-fcs (12/06/2007))): oracle.toplink.essentials.exceptions.PersistenceUnitLoadingException Exception Description: An exception was thrown while searching for persistence archives with ClassLoader: sun.misc.Launcher$AppClassLoader@11b86e7 Internal Exception: javax.persistence.PersistenceException: Exception [TOPLINK-28018] (Oracle TopLink Essentials - 2.0.1 (Build b09d-fcs (12/06/2007))): oracle.toplink.essentials.exceptions.EntityManagerSetupException Exception Description: predeploy for PersistenceUnit [MyBusinessRecordsPU] failed. Internal Exception: Exception [TOPLINK-7244] (Oracle TopLink Essentials - 2.0.1 (Build b09d-fcs (12/06/2007))): oracle.toplink.essentials.exceptions.ValidationException Exception Description: An incompatible mapping has been encountered between [class test.Products] and [class test.Orders]. This usually occurs when the cardinality of a mapping does not correspond with the cardinality of its backpointer. at oracle.toplink.essentials.exceptions.PersistenceUnitLoadingException.exceptionSearchingForPersistenceResources(PersistenceUnitLoadingException.java:143) at oracle.toplink.essentials.ejb.cmp3.EntityManagerFactoryProvider.createEntityManagerFactory(EntityManagerFactoryProvider.java:169) at javax.persistence.Persistence.createEntityManagerFactory(Persistence.java:110) at javax.persistence.Persistence.createEntityManagerFactory(Persistence.java:83) at test.TestView.initComponents(TestView.java:337) at test.TestView.(TestView.java:39) at test.TestApp.startup(TestApp.java:19) at org.jdesktop.application.Application$1.run(Application.java:171) at java.awt.event.InvocationEvent.dispatch(InvocationEvent.java:209) at java.awt.EventQueue.dispatchEvent(EventQueue.java:597) at java.awt.EventDispatchThread.pumpOneEventForFilters(EventDispatchThread.java:269) at java.awt.EventDispatchThread.pumpEventsForFilter(EventDispatchThread.java:184) at java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java:174) at java.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:169) at java.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:161) at java.awt.EventDispatchThread.run(EventDispatchThread.java:122) Caused by: javax.persistence.PersistenceException: Exception [TOPLINK-28018] (Oracle TopLink Essentials - 2.0.1 (Build b09d-fcs (12/06/2007))): oracle.toplink.essentials.exceptions.EntityManagerSetupException Exception Description: predeploy for PersistenceUnit [MyBusinessRecordsPU] failed. Internal Exception: Exception [TOPLINK-7244] (Oracle TopLink Essentials - 2.0.1 (Build b09d-fcs (12/06/2007))): oracle.toplink.essentials.exceptions.ValidationException Exception Description: An incompatible mapping has been encountered between [class test.Products] and [class test.Orders]. This usually occurs when the cardinality of a mapping does not correspond with the cardinality of its backpointer. at oracle.toplink.essentials.internal.ejb.cmp3.EntityManagerSetupImpl.predeploy(EntityManagerSetupImpl.java:643) at oracle.toplink.essentials.internal.ejb.cmp3.JavaSECMPInitializer.callPredeploy(JavaSECMPInitializer.java:171) at oracle.toplink.essentials.internal.ejb.cmp3.JavaSECMPInitializer.initPersistenceUnits(JavaSECMPInitializer.java:239) at oracle.toplink.essentials.internal.ejb.cmp3.JavaSECMPInitializer.initialize(JavaSECMPInitializer.java:255) at oracle.toplink.essentials.ejb.cmp3.EntityManagerFactoryProvider.createEntityManagerFactory(EntityManagerFactoryProvider.java:155) ... 14 more Caused by: Exception [TOPLINK-28018] (Oracle TopLink Essentials - 2.0.1 (Build b09d-fcs (12/06/2007))): oracle.toplink.essentials.exceptions.EntityManagerSetupException Exception Description: predeploy for PersistenceUnit [MyBusinessRecordsPU] failed. Internal Exception: Exception [TOPLINK-7244] (Oracle TopLink Essentials - 2.0.1 (Build b09d-fcs (12/06/2007))): oracle.toplink.essentials.exceptions.ValidationException Exception Description: An incompatible mapping has been encountered between [class test.Products] and [class test.Orders]. This usually occurs when the cardinality of a mapping does not correspond with the cardinality of its backpointer. at oracle.toplink.essentials.exceptions.EntityManagerSetupException.predeployFailed(EntityManagerSetupException.java:228) ... 19 more Caused by: Exception [TOPLINK-7244] (Oracle TopLink Essentials - 2.0.1 (Build b09d-fcs (12/06/2007))): oracle.toplink.essentials.exceptions.ValidationException Exception Description: An incompatible mapping has been encountered between [class test.Products] and [class test.Orders]. This usually occurs when the cardinality of a mapping does not correspond with the cardinality of its backpointer. at oracle.toplink.essentials.exceptions.ValidationException.invalidMapping(ValidationException.java:1069) at oracle.toplink.essentials.internal.ejb.cmp3.metadata.MetadataValidator.throwInvalidMappingEncountered(MetadataValidator.java:275) at oracle.toplink.essentials.internal.ejb.cmp3.metadata.accessors.OneToManyAccessor.process(OneToManyAccessor.java:161) at oracle.toplink.essentials.internal.ejb.cmp3.metadata.accessors.RelationshipAccessor.processRelationship(RelationshipAccessor.java:290) at oracle.toplink.essentials.internal.ejb.cmp3.metadata.MetadataProject.processRelationshipDescriptors(MetadataProject.java:579) at oracle.toplink.essentials.internal.ejb.cmp3.metadata.MetadataProject.process(MetadataProject.java:512) at oracle.toplink.essentials.internal.ejb.cmp3.metadata.MetadataProcessor.processAnnotations(MetadataProcessor.java:246) at oracle.toplink.essentials.ejb.cmp3.persistence.PersistenceUnitProcessor.processORMetadata(PersistenceUnitProcessor.java:370) at oracle.toplink.essentials.internal.ejb.cmp3.EntityManagerSetupImpl.predeploy(EntityManagerSetupImpl.java:607) ... 18 more The following providers: oracle.toplink.essentials.ejb.cmp3.EntityManagerFactoryProvider Returned null to createEntityManagerFactory. at javax.persistence.Persistence.createEntityManagerFactory(Persistence.java:154) at javax.persistence.Persistence.createEntityManagerFactory(Persistence.java:83) at test.TestView.initComponents(TestView.java:337) at test.TestView.(TestView.java:39) at test.TestApp.startup(TestApp.java:19) at org.jdesktop.application.Application$1.run(Application.java:171) at java.awt.event.InvocationEvent.dispatch(InvocationEvent.java:209) at java.awt.EventQueue.dispatchEvent(EventQueue.java:597) at java.awt.EventDispatchThread.pumpOneEventForFilters(EventDispatchThread.java:269) at java.awt.EventDispatchThread.pumpEventsForFilter(EventDispatchThread.java:184) at java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java:174) at java.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:169) at java.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:161) at java.awt.EventDispatchThread.run(EventDispatchThread.java:122) Exception in thread "AWT-EventQueue-0" java.lang.Error: Application class test.TestApp failed to launch at org.jdesktop.application.Application$1.run(Application.java:177) at java.awt.event.InvocationEvent.dispatch(InvocationEvent.java:209) at java.awt.EventQueue.dispatchEvent(EventQueue.java:597) at java.awt.EventDispatchThread.pumpOneEventForFilters(EventDispatchThread.java:269) at java.awt.EventDispatchThread.pumpEventsForFilter(EventDispatchThread.java:184) at java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java:174) at java.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:169) at java.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:161) at java.awt.EventDispatchThread.run(EventDispatchThread.java:122) Caused by: javax.persistence.PersistenceException: No Persistence provider for EntityManager named MyBusinessRecordsPU: Provider named oracle.toplink.essentials.PersistenceProvider threw unexpected exception at create EntityManagerFactory: oracle.toplink.essentials.exceptions.PersistenceUnitLoadingException Local Exception Stack: Exception [TOPLINK-30005] (Oracle TopLink Essentials - 2.0.1 (Build b09d-fcs (12/06/2007))): oracle.toplink.essentials.exceptions.PersistenceUnitLoadingException Exception Description: An exception was thrown while searching for persistence archives with ClassLoader: sun.misc.Launcher$AppClassLoader@11b86e7 Internal Exception: javax.persistence.PersistenceException: Exception [TOPLINK-28018] (Oracle TopLink Essentials - 2.0.1 (Build b09d-fcs (12/06/2007))): oracle.toplink.essentials.exceptions.EntityManagerSetupException Exception Description: predeploy for PersistenceUnit [MyBusinessRecordsPU] failed. Internal Exception: Exception [TOPLINK-7244] (Oracle TopLink Essentials - 2.0.1 (Build b09d-fcs (12/06/2007))): oracle.toplink.essentials.exceptions.ValidationException Exception Description: An incompatible mapping has been encountered between [class test.Products] and [class test.Orders]. This usually occurs when the cardinality of a mapping does not correspond with the cardinality of its backpointer. at oracle.toplink.essentials.exceptions.PersistenceUnitLoadingException.exceptionSearchingForPersistenceResources(PersistenceUnitLoadingException.java:143) at oracle.toplink.essentials.ejb.cmp3.EntityManagerFactoryProvider.createEntityManagerFactory(EntityManagerFactoryProvider.java:169) at javax.persistence.Persistence.createEntityManagerFactory(Persistence.java:110) at javax.persistence.Persistence.createEntityManagerFactory(Persistence.java:83) at test.TestView.initComponents(TestView.java:337) at test.TestView.(TestView.java:39) at test.TestApp.startup(TestApp.java:19) at org.jdesktop.application.Application$1.run(Application.java:171) at java.awt.event.InvocationEvent.dispatch(InvocationEvent.java:209) at java.awt.EventQueue.dispatchEvent(EventQueue.java:597) at java.awt.EventDispatchThread.pumpOneEventForFilters(EventDispatchThread.java:269) at java.awt.EventDispatchThread.pumpEventsForFilter(EventDispatchThread.java:184) at java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java:174) at java.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:169) at java.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:161) at java.awt.EventDispatchThread.run(EventDispatchThread.java:122) Caused by: javax.persistence.PersistenceException: Exception [TOPLINK-28018] (Oracle TopLink Essentials - 2.0.1 (Build b09d-fcs (12/06/2007))): oracle.toplink.essentials.exceptions.EntityManagerSetupException Exception Description: predeploy for PersistenceUnit [MyBusinessRecordsPU] failed. Internal Exception: Exception [TOPLINK-7244] (Oracle TopLink Essentials - 2.0.1 (Build b09d-fcs (12/06/2007))): oracle.toplink.essentials.exceptions.ValidationException Exception Description: An incompatible mapping has been encountered between [class test.Products] and [class test.Orders]. This usually occurs when the cardinality of a mapping does not correspond with the cardinality of its backpointer. at oracle.toplink.essentials.internal.ejb.cmp3.EntityManagerSetupImpl.predeploy(EntityManagerSetupImpl.java:643) at oracle.toplink.essentials.internal.ejb.cmp3.JavaSECMPInitializer.callPredeploy(JavaSECMPInitializer.java:171) at oracle.toplink.essentials.internal.ejb.cmp3.JavaSECMPInitializer.initPersistenceUnits(JavaSECMPInitializer.java:239) at oracle.toplink.essentials.internal.ejb.cmp3.JavaSECMPInitializer.initialize(JavaSECMPInitializer.java:255) at oracle.toplink.essentials.ejb.cmp3.EntityManagerFactoryProvider.createEntityManagerFactory(EntityManagerFactoryProvider.java:155) ... 14 more Caused by: Exception [TOPLINK-28018] (Oracle TopLink Essentials - 2.0.1 (Build b09d-fcs (12/06/2007))): oracle.toplink.essentials.exceptions.EntityManagerSetupException Exception Description: predeploy for PersistenceUnit [MyBusinessRecordsPU] failed. Internal Exception: Exception [TOPLINK-7244] (Oracle TopLink Essentials - 2.0.1 (Build b09d-fcs (12/06/2007))): oracle.toplink.essentials.exceptions.ValidationException Exception Description: An incompatible mapping has been encountered between [class test.Products] and [class test.Orders]. This usually occurs when the cardinality of a mapping does not correspond with the cardinality of its backpointer. at oracle.toplink.essentials.exceptions.EntityManagerSetupException.predeployFailed(EntityManagerSetupException.java:228) ... 19 more Caused by: Exception [TOPLINK-7244] (Oracle TopLink Essentials - 2.0.1 (Build b09d-fcs (12/06/2007))): oracle.toplink.essentials.exceptions.ValidationException Exception Description: An incompatible mapping has been encountered between [class test.Products] and [class test.Orders]. This usually occurs when the cardinality of a mapping does not correspond with the cardinality of its backpointer. at oracle.toplink.essentials.exceptions.ValidationException.invalidMapping(ValidationException.java:1069) at oracle.toplink.essentials.internal.ejb.cmp3.metadata.MetadataValidator.throwInvalidMappingEncountered(MetadataValidator.java:275) at oracle.toplink.essentials.internal.ejb.cmp3.metadata.accessors.OneToManyAccessor.process(OneToManyAccessor.java:161) at oracle.toplink.essentials.internal.ejb.cmp3.metadata.accessors.RelationshipAccessor.processRelationship(RelationshipAccessor.java:290) at oracle.toplink.essentials.internal.ejb.cmp3.metadata.MetadataProject.processRelationshipDescriptors(MetadataProject.java:579) at oracle.toplink.essentials.internal.ejb.cmp3.metadata.MetadataProject.process(MetadataProject.java:512) at oracle.toplink.essentials.internal.ejb.cmp3.metadata.MetadataProcessor.processAnnotations(MetadataProcessor.java:246) at oracle.toplink.essentials.ejb.cmp3.persistence.PersistenceUnitProcessor.processORMetadata(PersistenceUnitProcessor.java:370) at oracle.toplink.essentials.internal.ejb.cmp3.EntityManagerSetupImpl.predeploy(EntityManagerSetupImpl.java:607) ... 18 more The following providers: oracle.toplink.essentials.ejb.cmp3.EntityManagerFactoryProvider Returned null to createEntityManagerFactory. at javax.persistence.Persistence.createEntityManagerFactory(Persistence.java:154) at javax.persistence.Persistence.createEntityManagerFactory(Persistence.java:83) at test.TestView.initComponents(TestView.java:337) at test.TestView.(TestView.java:39) at test.TestApp.startup(TestApp.java:19) at org.jdesktop.application.Application$1.run(Application.java:171) ... 8 more BUILD SUCCESSFUL (total time: 2 seconds) I'm thinking my netbeans application must be misconfigured or something, I can't seem to find anyone with the same problem as myself

Read the article

'SImple' 2 class Java calculator doesn't accept inputs or do calculations

- by Tony O'Keeffe

Hi, I'm trying to get a two class java calculator working (new to java) to work but so far i'm having no success. the two classes are outlined below, calcFrame is for the interface and calEngine should do the actual calculations but i can't get them to talk to one another. i'd really appreciate any assistance on same. Thanks. CalcFrame Code - import java.awt.; import javax.swing.; import javax.swing.border.; import java.awt.event.; /** *A Class that operates as the framework for a calculator. *No calculations are performed in this section */ public class CalcFrame implements ActionListener { private CalcEngine calc; private JFrame frame; private JTextField display; private JLabel status; /** * Constructor for objects of class GridLayoutExample */ public CalcFrame() { makeFrame(); //calc = engine; } /** * This allows you to quit the calculator. */ // Alows the class to quit. private void quit() { System.exit(0); } // Calls the dialog frame with the information about the project. private void showAbout() { JOptionPane.showMessageDialog(frame, "Group Project", "About Calculator Group Project", JOptionPane.INFORMATION_MESSAGE); } private void makeFrame() { frame = new JFrame("Group Project Calculator"); makeMenuBar(frame); JPanel contentPane = (JPanel)frame.getContentPane(); contentPane.setLayout(new BorderLayout(8, 8)); contentPane.setBorder(new EmptyBorder( 10, 10, 10, 10)); /** * Insert a text field */ display = new JTextField(); contentPane.add(display, BorderLayout.NORTH); //Container contentPane = frame.getContentPane(); contentPane.setLayout(new GridLayout(4, 4)); JPanel buttonPanel = new JPanel(new GridLayout(4, 4)); contentPane.add(new JButton("1")); contentPane.add(new JButton("2")); contentPane.add(new JButton("3")); contentPane.add(new JButton("4")); contentPane.add(new JButton("5")); contentPane.add(new JButton("6")); contentPane.add(new JButton("7")); contentPane.add(new JButton("8")); contentPane.add(new JButton("9")); contentPane.add(new JButton("0")); contentPane.add(new JButton("+")); contentPane.add(new JButton("-")); contentPane.add(new JButton("/")); contentPane.add(new JButton("*")); contentPane.add(new JButton("=")); contentPane.add(new JButton("C")); contentPane.add(buttonPanel, BorderLayout.CENTER); //status = new JLabel(calc.getAuthor()); //contentPane.add(status, BorderLayout.SOUTH); frame.pack(); frame.setVisible(true); } /** * Create the main frame's menu bar. * The frame that the menu bar should be added to. */ private void makeMenuBar(JFrame frame) { final int SHORTCUT_MASK = Toolkit.getDefaultToolkit().getMenuShortcutKeyMask(); JMenuBar menubar = new JMenuBar(); frame.setJMenuBar(menubar); JMenu menu; JMenuItem item; // create the File menu menu = new JMenu("File"); menubar.add(menu); // create the Quit menu with a shortcut "Q" key. item = new JMenuItem("Quit"); item.setAccelerator(KeyStroke.getKeyStroke(KeyEvent.VK_Q, SHORTCUT_MASK)); item.addActionListener(new ActionListener() { public void actionPerformed(ActionEvent e) { quit(); } }); menu.add(item); // Adds an about menu. menu = new JMenu("About"); menubar.add(menu); // Displays item = new JMenuItem("Calculator Project"); item.addActionListener(new ActionListener() { public void actionPerformed(ActionEvent e) { showAbout(); } }); menu.add(item); } /** * An interface action has been performed. * Find out what it was and handle it. * @param event The event that has occured. */ public void actionPerformed(ActionEvent event) { String command = event.getActionCommand(); if(command.equals("0") || command.equals("1") || command.equals("2") || command.equals("3") || command.equals("4") || command.equals("5") || command.equals("6") || command.equals("7") || command.equals("8") || command.equals("9")) { int number = Integer.parseInt(command); calc.numberPressed(number); } else if(command.equals("+")) { calc.plus(); } else if(command.equals("-")) { calc.minus(); } else if(command.equals("=")) { calc.equals(); } else if(command.equals("C")) { calc.clear(); } else if(command.equals("?")) { } // else unknown command. redisplay(); } /** * Update the interface display to show the current value of the * calculator. */ private void redisplay() { display.setText("" + calc.getDisplayValue()); } /** * Toggle the info display in the calculator's status area between the * author and version information. */ } CalcEngine - public class CalcEngine { // The calculator's state is maintained in three fields: // buildingDisplayValue, haveLeftOperand, and lastOperator. // The current value (to be) shown in the display. private int displayValue; // The value of an existing left operand. private int leftOperand; /** * Create a CalcEngine. */ public CalcEngine() { clear(); } public int getDisplayValue() { return displayValue; } /** * A number button was pressed. * Either start a new operand, or incorporate this number as * the least significant digit of an existing one. * @param number The number pressed on the calculator. */ public void numberPressed(int number) { if(buildingDisplayValue) { // Incorporate this digit. displayValue = displayValue*10 + number; } else { // Start building a new number. displayValue = number; buildingDisplayValue = true; } } /** * The 'plus' button was pressed. */ public void plus() { applyOperator('+'); } /** * The 'minus' button was pressed. */ public void minus() { applyOperator('-'); } /** * The '=' button was pressed. */ public void equals() { // This should completes the building of a second operand, // so ensure that we really have a left operand, an operator // and a right operand. if(haveLeftOperand && lastOperator != '?' && buildingDisplayValue) { calculateResult(); lastOperator = '?'; buildingDisplayValue = false; } else { keySequenceError(); } } /** * The 'C' (clear) button was pressed. * Reset everything to a starting state. */ public void clear() { lastOperator = '?'; haveLeftOperand = false; buildingDisplayValue = false; displayValue = 0; } /** * @return The title of this calculation engine. */ public String getTitle() { return "Java Calculator"; } /** * @return The author of this engine. */ public String getAuthor() { return "David J. Barnes and Michael Kolling"; } /** * @return The version number of this engine. */ public String getVersion() { return "Version 1.0"; } /** * Combine leftOperand, lastOperator, and the * current display value. * The result becomes both the leftOperand and * the new display value. */ private void calculateResult() { switch(lastOperator) { case '+': displayValue = leftOperand + displayValue; haveLeftOperand = true; leftOperand = displayValue; break; case '-': displayValue = leftOperand - displayValue; haveLeftOperand = true; leftOperand = displayValue; break; default: keySequenceError(); break; } } /** * Apply an operator. * @param operator The operator to apply. */ private void applyOperator(char operator) { // If we are not in the process of building a new operand // then it is an error, unless we have just calculated a // result using '='. if(!buildingDisplayValue && !(haveLeftOperand && lastOperator == '?')) { keySequenceError(); return; } if(lastOperator != '?') { // First apply the previous operator. calculateResult(); } else { // The displayValue now becomes the left operand of this // new operator. haveLeftOperand = true; leftOperand = displayValue; } lastOperator = operator; buildingDisplayValue = false; } /** * Report an error in the sequence of keys that was pressed. */ private void keySequenceError() { System.out.println("A key sequence error has occurred."); // Reset everything. clear(); } }

Read the article

PyQt4: Scrollbar doesn't show in scrollarea when resizing dockWidget

- by Whospal

I created a python test program (Test_InfoPanel.py) that has MainWindow with dockWidget, and within it, a tabWidget with scrollArea widget. However, when I resize the MainWindow, the vertical scrollbar doesn't auto-appear when the Similarly, when I undock the dockWidget & resize, the vertical scrollbar doesn't auto-appear. Pls help! Test Program (Test_InfoPanel.py): #!/usr/bin/env python # Filename: Test_InfoPanel.py # Date: 2012-Sep-18 ''' This program test the scrollarea to show scrollbars for the InfoPanel_UI. ''' import sys from PyQt4 import QtCore, QtGui if __name__ == "__main__": import sys app = QtGui.QApplication(sys.argv) # Look and feel changed to 'Cleanlooks'. app.setStyle('Cleanlooks') from InfoPanel_UI import Ui_MainWindow_InfoPanel AppWindow = QtGui.QMainWindow() ui = Ui_MainWindow_InfoPanel() ui.setupUi(AppWindow) ui.tabWidget_Info_Panel.setCurrentWidget(ui.scrollArea_Info_Panel) AppWindow.show() sys.exit(app.exec_()) Generated *.ui script (InfoPanel_UI.py): # -*- coding: utf-8 -*- # Form implementation generated from reading ui file 'InfoPanel.ui' # # Created: Wed Sep 19 13:11:06 2012 # by: PyQt4 UI code generator 4.9.4 # # WARNING! All changes made in this file will be lost! from PyQt4 import QtCore, QtGui try: _fromUtf8 = QtCore.QString.fromUtf8 except AttributeError: _fromUtf8 = lambda s: s class Ui_MainWindow_InfoPanel(object): def setupUi(self, MainWindow_InfoPanel): MainWindow_InfoPanel.setObjectName(_fromUtf8("MainWindow_InfoPanel")) MainWindow_InfoPanel.resize(602, 263) MainWindow_InfoPanel.setDocumentMode(False) self.centralwidget = QtGui.QWidget(MainWindow_InfoPanel) self.centralwidget.setObjectName(_fromUtf8("centralwidget")) MainWindow_InfoPanel.setCentralWidget(self.centralwidget) self.statusbar = QtGui.QStatusBar(MainWindow_InfoPanel) self.statusbar.setObjectName(_fromUtf8("statusbar")) MainWindow_InfoPanel.setStatusBar(self.statusbar) self.dockWidget_Info_Panel = QtGui.QDockWidget(MainWindow_InfoPanel) self.dockWidget_Info_Panel.setMinimumSize(QtCore.QSize(300, 140)) font = QtGui.QFont() font.setBold(True) font.setItalic(True) font.setWeight(75) self.dockWidget_Info_Panel.setFont(font) self.dockWidget_Info_Panel.setLayoutDirection(QtCore.Qt.LeftToRight) self.dockWidget_Info_Panel.setAllowedAreas(QtCore.Qt.LeftDockWidgetArea|QtCore.Qt.RightDockWidgetArea) self.dockWidget_Info_Panel.setObjectName(_fromUtf8("dockWidget_Info_Panel")) self.dockWidgetContents_Info_Panel = QtGui.QWidget() self.dockWidgetContents_Info_Panel.setObjectName(_fromUtf8("dockWidgetContents_Info_Panel")) self.tabWidget_Info_Panel = QtGui.QTabWidget(self.dockWidgetContents_Info_Panel) self.tabWidget_Info_Panel.setGeometry(QtCore.QRect(0, 0, 300, 215)) font = QtGui.QFont() font.setBold(False) font.setItalic(False) font.setWeight(50) self.tabWidget_Info_Panel.setFont(font) self.tabWidget_Info_Panel.setObjectName(_fromUtf8("tabWidget_Info_Panel")) self.tab_1 = QtGui.QWidget() self.tab_1.setObjectName(_fromUtf8("tab_1")) self.scrollArea_Info_Panel = QtGui.QScrollArea(self.tab_1) self.scrollArea_Info_Panel.setGeometry(QtCore.QRect(9, 9, 271, 171)) self.scrollArea_Info_Panel.setVerticalScrollBarPolicy(QtCore.Qt.ScrollBarAsNeeded) self.scrollArea_Info_Panel.setWidgetResizable(True) self.scrollArea_Info_Panel.setObjectName(_fromUtf8("scrollArea_Info_Panel")) self.scrollAreaWidgetContents = QtGui.QWidget() self.scrollAreaWidgetContents.setGeometry(QtCore.QRect(0, 0, 269, 169)) self.scrollAreaWidgetContents.setObjectName(_fromUtf8("scrollAreaWidgetContents")) self.frame_Info_Panel = QtGui.QFrame(self.scrollAreaWidgetContents) self.frame_Info_Panel.setGeometry(QtCore.QRect(0, 0, 261, 161)) self.frame_Info_Panel.setObjectName(_fromUtf8("frame_Info_Panel")) self.label_Eqpt_Model = QtGui.QLabel(self.frame_Info_Panel) self.label_Eqpt_Model.setGeometry(QtCore.QRect(10, 10, 111, 27)) self.label_Eqpt_Model.setObjectName(_fromUtf8("label_Eqpt_Model")) self.lineEdit_Eqpt_Model = QtGui.QLineEdit(self.frame_Info_Panel) self.lineEdit_Eqpt_Model.setEnabled(False) self.lineEdit_Eqpt_Model.setGeometry(QtCore.QRect(120, 10, 111, 27)) palette = QtGui.QPalette() brush = QtGui.QBrush(QtGui.QColor(60, 60, 60)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Active, QtGui.QPalette.Text, brush) brush = QtGui.QBrush(QtGui.QColor(60, 60, 60)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Inactive, QtGui.QPalette.Text, brush) brush = QtGui.QBrush(QtGui.QColor(0, 0, 127)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Disabled, QtGui.QPalette.Text, brush) self.lineEdit_Eqpt_Model.setPalette(palette) self.lineEdit_Eqpt_Model.setObjectName(_fromUtf8("lineEdit_Eqpt_Model")) self.label_State = QtGui.QLabel(self.frame_Info_Panel) self.label_State.setGeometry(QtCore.QRect(10, 40, 111, 27)) self.label_State.setObjectName(_fromUtf8("label_State")) self.lineEdit_State = QtGui.QLineEdit(self.frame_Info_Panel) self.lineEdit_State.setEnabled(False) self.lineEdit_State.setGeometry(QtCore.QRect(120, 40, 111, 27)) palette = QtGui.QPalette() brush = QtGui.QBrush(QtGui.QColor(60, 60, 60)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Active, QtGui.QPalette.Text, brush) brush = QtGui.QBrush(QtGui.QColor(60, 60, 60)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Inactive, QtGui.QPalette.Text, brush) brush = QtGui.QBrush(QtGui.QColor(0, 0, 127)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Disabled, QtGui.QPalette.Text, brush) self.lineEdit_State.setPalette(palette) self.lineEdit_State.setObjectName(_fromUtf8("lineEdit_State")) self.groupBox_Current_Position = QtGui.QGroupBox(self.frame_Info_Panel) self.groupBox_Current_Position.setGeometry(QtCore.QRect(10, 70, 241, 91)) palette = QtGui.QPalette() brush = QtGui.QBrush(QtGui.QColor(0, 0, 0)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Active, QtGui.QPalette.WindowText, brush) brush = QtGui.QBrush(QtGui.QColor(85, 255, 0)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Active, QtGui.QPalette.Button, brush) brush = QtGui.QBrush(QtGui.QColor(170, 255, 127)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Active, QtGui.QPalette.Light, brush) brush = QtGui.QBrush(QtGui.QColor(127, 255, 63)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Active, QtGui.QPalette.Midlight, brush) brush = QtGui.QBrush(QtGui.QColor(42, 127, 0)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Active, QtGui.QPalette.Dark, brush) brush = QtGui.QBrush(QtGui.QColor(56, 170, 0)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Active, QtGui.QPalette.Mid, brush) brush = QtGui.QBrush(QtGui.QColor(0, 0, 0)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Active, QtGui.QPalette.Text, brush) brush = QtGui.QBrush(QtGui.QColor(255, 255, 255)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Active, QtGui.QPalette.BrightText, brush) brush = QtGui.QBrush(QtGui.QColor(0, 0, 0)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Active, QtGui.QPalette.ButtonText, brush) brush = QtGui.QBrush(QtGui.QColor(255, 255, 255)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Active, QtGui.QPalette.Base, brush) brush = QtGui.QBrush(QtGui.QColor(85, 255, 0)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Active, QtGui.QPalette.Window, brush) brush = QtGui.QBrush(QtGui.QColor(0, 0, 0)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Active, QtGui.QPalette.Shadow, brush) brush = QtGui.QBrush(QtGui.QColor(170, 255, 127)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Active, QtGui.QPalette.AlternateBase, brush) brush = QtGui.QBrush(QtGui.QColor(255, 255, 220)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Active, QtGui.QPalette.ToolTipBase, brush) brush = QtGui.QBrush(QtGui.QColor(0, 0, 0)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Active, QtGui.QPalette.ToolTipText, brush) brush = QtGui.QBrush(QtGui.QColor(0, 0, 0)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Inactive, QtGui.QPalette.WindowText, brush) brush = QtGui.QBrush(QtGui.QColor(85, 255, 0)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Inactive, QtGui.QPalette.Button, brush) brush = QtGui.QBrush(QtGui.QColor(170, 255, 127)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Inactive, QtGui.QPalette.Light, brush) brush = QtGui.QBrush(QtGui.QColor(127, 255, 63)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Inactive, QtGui.QPalette.Midlight, brush) brush = QtGui.QBrush(QtGui.QColor(42, 127, 0)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Inactive, QtGui.QPalette.Dark, brush) brush = QtGui.QBrush(QtGui.QColor(56, 170, 0)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Inactive, QtGui.QPalette.Mid, brush) brush = QtGui.QBrush(QtGui.QColor(0, 0, 0)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Inactive, QtGui.QPalette.Text, brush) brush = QtGui.QBrush(QtGui.QColor(255, 255, 255)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Inactive, QtGui.QPalette.BrightText, brush) brush = QtGui.QBrush(QtGui.QColor(0, 0, 0)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Inactive, QtGui.QPalette.ButtonText, brush) brush = QtGui.QBrush(QtGui.QColor(255, 255, 255)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Inactive, QtGui.QPalette.Base, brush) brush = QtGui.QBrush(QtGui.QColor(85, 255, 0)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Inactive, QtGui.QPalette.Window, brush) brush = QtGui.QBrush(QtGui.QColor(0, 0, 0)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Inactive, QtGui.QPalette.Shadow, brush) brush = QtGui.QBrush(QtGui.QColor(170, 255, 127)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Inactive, QtGui.QPalette.AlternateBase, brush) brush = QtGui.QBrush(QtGui.QColor(255, 255, 220)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Inactive, QtGui.QPalette.ToolTipBase, brush) brush = QtGui.QBrush(QtGui.QColor(0, 0, 0)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Inactive, QtGui.QPalette.ToolTipText, brush) brush = QtGui.QBrush(QtGui.QColor(42, 127, 0)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Disabled, QtGui.QPalette.WindowText, brush) brush = QtGui.QBrush(QtGui.QColor(85, 255, 0)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Disabled, QtGui.QPalette.Button, brush) brush = QtGui.QBrush(QtGui.QColor(170, 255, 127)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Disabled, QtGui.QPalette.Light, brush) brush = QtGui.QBrush(QtGui.QColor(127, 255, 63)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Disabled, QtGui.QPalette.Midlight, brush) brush = QtGui.QBrush(QtGui.QColor(42, 127, 0)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Disabled, QtGui.QPalette.Dark, brush) brush = QtGui.QBrush(QtGui.QColor(56, 170, 0)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Disabled, QtGui.QPalette.Mid, brush) brush = QtGui.QBrush(QtGui.QColor(42, 127, 0)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Disabled, QtGui.QPalette.Text, brush) brush = QtGui.QBrush(QtGui.QColor(255, 255, 255)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Disabled, QtGui.QPalette.BrightText, brush) brush = QtGui.QBrush(QtGui.QColor(42, 127, 0)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Disabled, QtGui.QPalette.ButtonText, brush) brush = QtGui.QBrush(QtGui.QColor(85, 255, 0)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Disabled, QtGui.QPalette.Base, brush) brush = QtGui.QBrush(QtGui.QColor(85, 255, 0)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Disabled, QtGui.QPalette.Window, brush) brush = QtGui.QBrush(QtGui.QColor(0, 0, 0)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Disabled, QtGui.QPalette.Shadow, brush) brush = QtGui.QBrush(QtGui.QColor(85, 255, 0)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Disabled, QtGui.QPalette.AlternateBase, brush) brush = QtGui.QBrush(QtGui.QColor(255, 255, 220)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Disabled, QtGui.QPalette.ToolTipBase, brush) brush = QtGui.QBrush(QtGui.QColor(0, 0, 0)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Disabled, QtGui.QPalette.ToolTipText, brush) self.groupBox_Current_Position.setPalette(palette) self.groupBox_Current_Position.setObjectName(_fromUtf8("groupBox_Current_Position")) self.label_Current_Position_X = QtGui.QLabel(self.groupBox_Current_Position) self.label_Current_Position_X.setGeometry(QtCore.QRect(20, 20, 41, 27)) self.label_Current_Position_X.setObjectName(_fromUtf8("label_Current_Position_X")) self.lineEdit_Current_Position_X = QtGui.QLineEdit(self.groupBox_Current_Position) self.lineEdit_Current_Position_X.setEnabled(False) self.lineEdit_Current_Position_X.setGeometry(QtCore.QRect(60, 20, 161, 27)) palette = QtGui.QPalette() brush = QtGui.QBrush(QtGui.QColor(60, 60, 60)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Active, QtGui.QPalette.Text, brush) brush = QtGui.QBrush(QtGui.QColor(60, 60, 60)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Inactive, QtGui.QPalette.Text, brush) brush = QtGui.QBrush(QtGui.QColor(0, 0, 127)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Disabled, QtGui.QPalette.Text, brush) self.lineEdit_Current_Position_X.setPalette(palette) self.lineEdit_Current_Position_X.setObjectName(_fromUtf8("lineEdit_Current_Position_X")) self.label_Current_Position_Y = QtGui.QLabel(self.groupBox_Current_Position) self.label_Current_Position_Y.setGeometry(QtCore.QRect(20, 50, 41, 27)) self.label_Current_Position_Y.setObjectName(_fromUtf8("label_Current_Position_Y")) self.lineEdit_Current_Position_Y = QtGui.QLineEdit(self.groupBox_Current_Position) self.lineEdit_Current_Position_Y.setEnabled(False) self.lineEdit_Current_Position_Y.setGeometry(QtCore.QRect(60, 50, 161, 27)) palette = QtGui.QPalette() brush = QtGui.QBrush(QtGui.QColor(60, 60, 60)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Active, QtGui.QPalette.Text, brush) brush = QtGui.QBrush(QtGui.QColor(60, 60, 60)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Inactive, QtGui.QPalette.Text, brush) brush = QtGui.QBrush(QtGui.QColor(0, 0, 127)) brush.setStyle(QtCore.Qt.SolidPattern) palette.setBrush(QtGui.QPalette.Disabled, QtGui.QPalette.Text, brush) self.lineEdit_Current_Position_Y.setPalette(palette) self.lineEdit_Current_Position_Y.setObjectName(_fromUtf8("lineEdit_Current_Position_Y")) self.scrollArea_Info_Panel.setWidget(self.scrollAreaWidgetContents) self.tabWidget_Info_Panel.addTab(self.tab_1, _fromUtf8("")) self.tab_2 = QtGui.QWidget() self.tab_2.setObjectName(_fromUtf8("tab_2")) self.tabWidget_Info_Panel.addTab(self.tab_2, _fromUtf8("")) self.dockWidget_Info_Panel.setWidget(self.dockWidgetContents_Info_Panel) MainWindow_InfoPanel.addDockWidget(QtCore.Qt.DockWidgetArea(2), self.dockWidget_Info_Panel) self.retranslateUi(MainWindow_InfoPanel) self.tabWidget_Info_Panel.setCurrentIndex(0) QtCore.QMetaObject.connectSlotsByName(MainWindow_InfoPanel) def retranslateUi(self, MainWindow_InfoPanel): MainWindow_InfoPanel.setWindowTitle(QtGui.QApplication.translate("MainWindow_InfoPanel", "MainWindow Info Panel", None, QtGui.QApplication.UnicodeUTF8)) self.dockWidget_Info_Panel.setWindowTitle(QtGui.QApplication.translate("MainWindow_InfoPanel", "Info Panel", None, QtGui.QApplication.UnicodeUTF8)) self.label_Eqpt_Model.setText(QtGui.QApplication.translate("MainWindow_InfoPanel", "Eqpt Model:", None, QtGui.QApplication.UnicodeUTF8)) self.lineEdit_Eqpt_Model.setText(QtGui.QApplication.translate("MainWindow_InfoPanel", "ABC", None, QtGui.QApplication.UnicodeUTF8)) self.label_State.setText(QtGui.QApplication.translate("MainWindow_InfoPanel", "State:", None, QtGui.QApplication.UnicodeUTF8)) self.lineEdit_State.setText(QtGui.QApplication.translate("MainWindow_InfoPanel", "Working", None, QtGui.QApplication.UnicodeUTF8)) self.groupBox_Current_Position.setTitle(QtGui.QApplication.translate("MainWindow_InfoPanel", "Current Position:", None, QtGui.QApplication.UnicodeUTF8)) self.label_Current_Position_X.setText(QtGui.QApplication.translate("MainWindow_InfoPanel", "X =", None, QtGui.QApplication.UnicodeUTF8)) self.lineEdit_Current_Position_X.setText(QtGui.QApplication.translate("MainWindow_InfoPanel", "1000.00 m", None, QtGui.QApplication.UnicodeUTF8)) self.label_Current_Position_Y.setText(QtGui.QApplication.translate("MainWindow_InfoPanel", "Y =", None, QtGui.QApplication.UnicodeUTF8)) self.lineEdit_Current_Position_Y.setText(QtGui.QApplication.translate("MainWindow_InfoPanel", "1000.00 m", None, QtGui.QApplication.UnicodeUTF8)) self.tabWidget_Info_Panel.setTabText(self.tabWidget_Info_Panel.indexOf(self.tab_1), QtGui.QApplication.translate("MainWindow_InfoPanel", "Info_Pg 1", None, QtGui.QApplication.UnicodeUTF8)) self.tabWidget_Info_Panel.setTabText(self.tabWidget_Info_Panel.indexOf(self.tab_2), QtGui.QApplication.translate("MainWindow_InfoPanel", "Info_Pg 2", None, QtGui.QApplication.UnicodeUTF8)) PS: I initially created the mainWindow as a Dialog, but realized that after undock & redock, the dockWidget doesn't dock properly. Somehow there's an offset. This doesn't seem to be a problem if the mainWindow is a QtGui.QMainWindow instead of a QtGui.QDialog.

Read the article

Problem when trying to connect to a desktop server from android on wifi

- by thiagolee

Hello, I am trying to send a file from the phone running Android 1.5 to a server on a desktop. I wrote some code, which works on emulator, but on the phone it doesn't. I'm connecting to the network through WiFi. It works, I can access the internet through my phone and I've configured my router. The application stops when I'm trying to connect. I have the permissions. Someone have any ideas, below is my code. Running on Android package br.ufs.reconhecimento; import java.io.DataInputStream; import java.io.DataOutputStream; import java.io.File; import java.io.FileInputStream; import java.io.IOException; import java.net.Socket; import android.app.Activity; import android.app.AlertDialog; import android.content.DialogInterface; import android.content.Intent; import android.os.Bundle; import android.util.Log; import android.view.View; import android.view.View.OnClickListener; import android.widget.EditText; import android.widget.ImageButton; /** * Sample code that invokes the speech recognition intent API. */ public class Reconhecimento extends Activity implements OnClickListener { static final int VOICE_RECOGNITION_REQUEST_CODE = 1234; static final String LOG_VOZ = "UFS-Reconhecimento"; final int INICIAR_GRAVACAO = 01; int porta = 5158; // Porta definida no servidor int tempoEspera = 1000; String ipConexao = "172.20.0.189"; EditText ipEdit; /** * Called with the activity is first created. */ @Override public void onCreate(Bundle savedInstanceState) { super.onCreate(savedInstanceState); // Inflate our UI from its XML layout description. setContentView(R.layout.main); // Get display items for later interaction ImageButton speakButton = (ImageButton) findViewById(R.id.btn_speak); speakButton.setPadding(10, 10, 10, 10); speakButton.setOnClickListener(this); //Alerta para o endereço IP AlertDialog.Builder alerta = new AlertDialog.Builder(this); alerta.setTitle("IP");//+mainWifi.getWifiState()); ipEdit = new EditText(this); ipEdit.setText(ipConexao); alerta.setView(ipEdit); alerta.setMessage("Por favor, Confirme o endereço IP."); alerta.setPositiveButton("OK", new DialogInterface.OnClickListener() { public void onClick(DialogInterface dialog, int which) { ipConexao = ipEdit.getText().toString(); Log.d(LOG_VOZ, "Nova Atribuição do Endreço IP: " + ipConexao); } }); alerta.create(); alerta.show(); } /** * Handle the click on the start recognition button. */ public void onClick(View v) { if (v.getId() == R.id.btn_speak) { //startVoiceRecognitionActivity(); Log.d(LOG_VOZ, "Iniciando a próxima tela"); Intent recordIntent = new Intent(this, GravacaoAtivity.class); Log.d(LOG_VOZ, "Iniciando a tela (instancia criada)"); startActivityForResult(recordIntent, INICIAR_GRAVACAO); Log.d(LOG_VOZ, "Gravação iniciada ..."); } } /** * Handle the results from the recognition activity. */ @Override protected void onActivityResult(int requestCode, int resultCode, Intent data) { Log.d(LOG_VOZ, "Iniciando onActivityResult()"); if (requestCode == INICIAR_GRAVACAO && resultCode == RESULT_OK) { String path = data.getStringExtra(GravacaoAtivity.RETORNO); conexaoSocket(path); } else Log.e(LOG_VOZ, "Resultado Inexperado ..."); } private void conexaoSocket(String path) { Socket socket = SocketOpener.openSocket(ipConexao, porta, tempoEspera); if(socket == null) return; try { DataOutputStream conexao = new DataOutputStream(socket.getOutputStream()); Log.d(LOG_VOZ, "Acessando arquivo ..."); File file = new File(path); DataInputStream arquivo = new DataInputStream(new FileInputStream(file)); Log.d(LOG_VOZ, "Iniciando Transmissão ..."); conexao.writeLong(file.length()); for(int i = 0; i < file.length(); i++) conexao.writeByte(arquivo.readByte()); Log.d(LOG_VOZ, "Transmissão realizada com sucesso..."); Log.d(LOG_VOZ, "Fechando a conexão..."); conexao.close(); socket.close(); Log.d(LOG_VOZ, "============ Processo finalizado com Sucesso =============="); } catch (IOException e) { Log.e(LOG_VOZ, "Erro ao fazer a conexão via Socket. " + e.getMessage()); // TODO Auto-generated catch block } } } class SocketOpener implements Runnable { private String host; private int porta; private Socket socket; public SocketOpener(String host, int porta) { this.host = host; this.porta = porta; socket = null; } public static Socket openSocket(String host, int porta, int timeOut) { SocketOpener opener = new SocketOpener(host, porta); Thread t = new Thread(opener); t.start(); try { t.join(timeOut); } catch(InterruptedException e) { Log.e(Reconhecimento.LOG_VOZ, "Erro ao fazer o join da thread do socket. " + e.getMessage()); //TODO: Mensagem informativa return null; } return opener.getSocket(); } public void run() { try { socket = new Socket(host, porta); }catch(IOException e) { Log.e(Reconhecimento.LOG_VOZ, "Erro na criação do socket. " + e.getMessage()); //TODO: Mensagem informativa } } public Socket getSocket() { return socket; } } Running on the desktop Java: import java.io.BufferedReader; import java.io.DataInputStream; import java.io.DataOutputStream; import java.io.File; import java.io.FileOutputStream; import java.io.IOException; import java.io.InputStreamReader; import java.net.ServerSocket; import java.net.Socket; public class ServidorArquivo { private static int porta = 5158; static String ARQUIVO = "voz.amr"; /** * Caminho que será gravado o arquivo de audio */ static String PATH = "/home/iade/Trabalho/lib/"; public static void main(String[] args) { int i = 1; try { System.out.println("Iniciando o Servidor Socket - Android."); ServerSocket s = new ServerSocket(porta); System.out.println("Servidor Iniciado com Sucesso..."); System.out.println("Aguardando conexões na porta: " + porta); while(true) { Socket recebendo = s.accept(); System.out.println("Aceitando conexão de nº " + i); new ThreadedHandler(recebendo).start(); i++; } } catch (Exception e) { System.out.println("Erro: " + e.getMessage()); e.printStackTrace(); } } } class ThreadedHandler extends Thread { private Socket socket; public ThreadedHandler(Socket so) { socket = so; } public void run() { DataInputStream entrada = null; DataOutputStream arquivo = null; try { entrada = new DataInputStream(socket.getInputStream()); System.out.println("========== Iniciando a leitura dos dados via Sockets =========="); long tamanho = entrada.readLong(); System.out.println("Tamanho do vetor " + tamanho); File file = new File(ServidorArquivo.PATH + ServidorArquivo.ARQUIVO); if(!file.exists()) file.createNewFile(); arquivo = new DataOutputStream(new FileOutputStream(file)); for(int j = 0; j < tamanho; j++) { arquivo.write(entrada.readByte()); } System.out.println("========== Dados recebidos com sucesso =========="); } catch (Exception e) { System.out.println("Erro ao tratar do socket: " + e.getMessage()); e.printStackTrace(); } finally { System.out.println("**** Fechando as conexões ****"); try { entrada.close(); socket.close(); arquivo.close(); } catch (IOException e) { System.out.println("Erro ao fechar conex�es " + e.getMessage()); e.printStackTrace(); } } System.out.println("============= Fim da Gravação ==========="); // tratar o arquivo String cmd1 = "ffmpeg -i voz.amr -ab 12288 -ar 16000 voz.wav"; String cmd2 = "soundstretch voz.wav voz2.wav -tempo=100"; String dir = "/home/iade/Trabalho/lib"; File workDir = new File(dir); File f1 = new File(dir+"/voz.wav"); File f2 = new File(dir+"/voz2.wav"); f1.delete(); f2.delete(); try { executeCommand(cmd1, workDir); System.out.println("realizou cmd1"); executeCommand(cmd2, workDir); System.out.println("realizou cmd2"); } catch (IOException e) { // TODO Auto-generated catch block e.printStackTrace(); } catch (InterruptedException e) { // TODO Auto-generated catch block e.printStackTrace(); } } private void executeCommand(String cmd1, File workDir) throws IOException, InterruptedException { String s; Process p = Runtime.getRuntime().exec(cmd1,null,workDir); int i = p.waitFor(); if (i == 0) { BufferedReader stdInput = new BufferedReader(new InputStreamReader(p.getInputStream())); // read the output from the command while ((s = stdInput.readLine()) != null) { System.out.println(s); } } else { BufferedReader stdErr = new BufferedReader(new InputStreamReader(p.getErrorStream())); // read the output from the command while ((s = stdErr.readLine()) != null) { System.out.println(s); } } } } Thanks in advance.

Read the article

TabHost disappears after locking the phone and reopening it:

- by Emil Adz

I have a weird issue with my TabHost in my FragmentActivity that contains a ViewPager. The problem is that when I close my phone (press the power button) while I use my application, and then I turn back the phone and my application gets reopened, at this point my TabHost is missing. So the closing of my phone is causes the TabHost to disappear. My guess would be that I need to save my tabHost state in the saveInstanceState object, and restore it in onResume I only have no idea how it's done. here is my code for the FragmentActivity: public class TabsViewPagerFragmentActivity extends FragmentActivity implements ViewPager.OnPageChangeListener, TabHost.OnTabChangeListener { static final String TAG = TabsViewPagerFragmentActivity.class.getSimpleName(); private TabHost mTabHost; private ViewPager mViewPager; private HashMap<String, TabInfo> mapTabInfo; public ViewPagerAdapter mPagerAdapter; private TextView tvReportName, tvTabTitle; private Button bBackToParameters; private Dialog progressDialog; private SGRaportManagerAppObj application; private int numberOfTabs = 0; private Display display; public static final int POPUP_MARGIN = 6; LeftSideMenu leftSideMenu; public void NotifyTabActivityViewPagerAdapter() { mPagerAdapter.notifyDataSetChanged(); } public ViewPagerAdapter getTabActivityViewPagerAdapter() { return mPagerAdapter; } public ViewPager getTabActivityViewPager() { return mViewPager; } public void setCurrentTabTitle (String title) { tvTabTitle.setText(title); Log.d(TAG, "set tab title from activity: "+title); } /** * Maintains extrinsic info of a tab's construct */ private class TabInfo { private String tag; private Class<?> clss; private Bundle args; private Fragment fragment; TabInfo(String tag, Class<?> clazz, Bundle args) { this.tag = tag; this.clss = clazz; this.args = args; } } /** * A simple factory that returns dummy views to the Tabhost */ class TabFactory implements TabContentFactory { private final Context mContext; /** * @param context */ public TabFactory(Context context) { mContext = context; } /** (non-Javadoc) * @see android.widget.TabHost.TabContentFactory#createTabContent(java.lang.String) */ public View createTabContent(String tag) { View v = new View(mContext); v.setMinimumWidth(0); v.setMinimumHeight(0); return v; } } /** (non-Javadoc) * @see android.support.v4.app.FragmentActivity#onCreate(android.os.Bundle) */ public void onCreate(Bundle savedInstanceState) { super.onCreate(savedInstanceState); application = SGRaportManagerAppObj.getInstance(); display = ((WindowManager)getSystemService(Context.WINDOW_SERVICE)).getDefaultDisplay(); // Inflate the layout setContentView(R.layout.tabs_screen_activity_layout); tvTabTitle = (TextView) findViewById(R.id.tvTabName); tvReportName = (TextView)findViewById(R.id.tvReportName); tvReportName.setText(application.currentReport.getName()+ " - "); bBackToParameters = (Button) findViewById(R.id.bBackToParameters); leftSideMenu = (LeftSideMenu) findViewById(R.id.leftSideMenu); applyOnClickListenerToLeftSideMenu(); findViewById(R.id.showLeftMenuButton).setOnClickListener(new View.OnClickListener() { @Override public void onClick(View v) { Display d = ((WindowManager)getSystemService(Context.WINDOW_SERVICE)).getDefaultDisplay(); int width = d.getWidth(); View panel = findViewById(R.id.leftSideMenu); View appPanel = findViewById(R.id.appLayout); if (panel.getVisibility() == View.GONE){ appPanel.setLayoutParams(new LinearLayout.LayoutParams(width, LayoutParams.FILL_PARENT)); panel.setVisibility(View.VISIBLE); applyOnClickListenerToLeftSideMenu(); }else{ ToggleButton button = (ToggleButton) findViewById(R.id.showLeftMenuButton); button.setChecked(false); panel.setVisibility(View.GONE); } } }); // Initialise the TabHost progressDialog = DialogUtils.createProgressDialog(this, this.getString(R.string.populating_view_pager)); progressDialog.show(); if (SGRaportManagerAppObj.getInstance().parametersRepository.getParametersRepository().size() == 0) { bBackToParameters.setText(R.string.back_to_report_list); } this.initialiseTabHost(savedInstanceState); if (savedInstanceState != null) { mTabHost.setCurrentTabByTag(savedInstanceState.getString("tab")); //set the tab as per the saved state } // Intialise ViewPager this.intialiseViewPager(); progressDialog.dismiss(); } /** (non-Javadoc) * @see android.support.v4.app.FragmentActivity#onSaveInstanceState(android.os.Bundle) */ protected void onSaveInstanceState(Bundle outState) { outState.putString("tab", mTabHost.getCurrentTabTag()); //save the tab selected super.onSaveInstanceState(outState); } /** * Initialise ViewPager */ public void intialiseViewPager() { List<Fragment> fragments = new Vector<Fragment>(); // TabInfo tabInfo = null; if (application.getCurrentDataSource().equals(DataSource.SSRS)) { numberOfTabs = application.currentReport.getTabsList().size(); } else if (application.getCurrentDataSource().equals(DataSource.SGRDL)) { numberOfTabs = application.currentReport.getODTabsList().size(); Log.d(TAG, "CURRENT REPORT FROM VIEW PAGER: "+ application.currentReport.toString()); } Log.d(TAG,"Current Tabs number from TabsViewPager activity: " +numberOfTabs); if (application.getCurrentDataSource().equals(DataSource.SSRS)) { for (int i = 0; i < numberOfTabs; i++) { Tab tempTab = application.currentReport.getTabsList().get(i); if (tempTab.getTabTemplateId() == 7) { GridFragment gridFragment = new GridFragment(tempTab); fragments.add(gridFragment); } else if (tempTab.getTabTemplateId() == 8) { NewChartFragment chartFragment = new NewChartFragment(tempTab, this); fragments.add(chartFragment); } } } else if (application.getCurrentDataSource().equals(DataSource.SGRDL)) { for (int i = 0; i < numberOfTabs; i++) { ODTab tempTab = application.currentReport.getODTabsList().get(i); if (tempTab.getTabType().equals(ODGrid.XML_GRID_ELEMENT)) { GridFragment gridFragment = GridFragment.newInstance(tempTab.getTabId()); fragments.add(gridFragment); } else if (tempTab.getTabType().equals(ODChart.XML_CHART_ELEMENT)) { NewChartFragment chartFragment = NewChartFragment.newInstance(tempTab.getTabId()); fragments.add(chartFragment); } } } Log.d(TAG, "Current report fragments set to adapter: "+fragments.toString()); /* if (this.mPagerAdapter == null) { this.mPagerAdapter = new ViewPagerAdapter(super.getSupportFragmentManager(), fragments); } else { this.mPagerAdapter.removeAllFragments(); this.mPagerAdapter.addFragmentsListToAdapter(fragments); } */ this.mPagerAdapter = new ViewPagerAdapter(super.getSupportFragmentManager(), fragments); this.mViewPager = (ViewPager)super.findViewById(R.id.pager); // this.mViewPager.setAdapter(null); this.mViewPager.setAdapter(this.mPagerAdapter); this.mViewPager.setOffscreenPageLimit(0); this.mViewPager.setOnPageChangeListener(this); Log.d(TAG, "Adapter initialized!"); } /** * Initialise the Tab Host */ public void initialiseTabHost(Bundle args) { mTabHost = (TabHost)findViewById(android.R.id.tabhost); /* //new edit if (mTabHost.getChildCount() > 0) { mTabHost.removeAllViews(); } */ mTabHost.setup(); TabInfo tabInfo = null; mapTabInfo = new HashMap<String, TabsViewPagerFragmentActivity.TabInfo>(); if (args != null) {} else { if (application.getCurrentDataSource().equals(DataSource.SSRS)) { int numberOfTabs = application.currentReport.getTabsList().size(); for (int i = 0; i < numberOfTabs; i++) { Tab tempTab = application.currentReport.getTabsList().get(i); if (tempTab.getTabTemplateId() == 7) { //GridFragment gridFragment = new GridFragment(tempTab); TabsViewPagerFragmentActivity.AddTab(this, this.mTabHost, this.mTabHost.newTabSpec("Tab "+String.valueOf(i)).setIndicator("Tab "+String.valueOf(i)), ( tabInfo = new TabInfo("Tab "+String.valueOf(i), GridFragment.class, args))); this.mapTabInfo.put(tabInfo.tag, tabInfo); } else if (tempTab.getTabTemplateId() == 8) { TabsViewPagerFragmentActivity.AddTab(this, this.mTabHost, this.mTabHost.newTabSpec("Tab "+String.valueOf(i)).setIndicator("Tab "+String.valueOf(i)), ( tabInfo = new TabInfo("Tab "+String.valueOf(i), NewChartFragment.class, args))); this.mapTabInfo.put(tabInfo.tag, tabInfo); } } } else if (application.getCurrentDataSource().equals(DataSource.SGRDL)) { int numberOfTabs = application.currentReport.getODTabsList().size(); for (int i = 0; i < numberOfTabs; i++) { ODTab tempTab = application.currentReport.getODTabsList().get(i); // Log.d(TAG,"Crashed Tab type: "+ tempTab.getTabType()); if (tempTab.getTabType().equals(ODGrid.XML_GRID_ELEMENT)) { //GridFragment gridFragment = new GridFragment(tempTab); TabsViewPagerFragmentActivity.AddTab(this, this.mTabHost, this.mTabHost.newTabSpec("Tab "+String.valueOf(i)).setIndicator("Tab "+String.valueOf(i)), ( tabInfo = new TabInfo("Tab "+String.valueOf(i), GridFragment.class, args))); this.mapTabInfo.put(tabInfo.tag, tabInfo); } else if (tempTab.getTabType().equals(ODChart.XML_CHART_ELEMENT)) { TabsViewPagerFragmentActivity.AddTab(this, this.mTabHost, this.mTabHost.newTabSpec("Tab "+String.valueOf(i)).setIndicator("Tab "+String.valueOf(i)), ( tabInfo = new TabInfo("Tab "+String.valueOf(i), NewChartFragment.class, args))); this.mapTabInfo.put(tabInfo.tag, tabInfo); } } } } // Default to first tab //this.onTabChanged("Tab1"); // mTabHost.setOnTabChangedListener(this); } /** * Add Tab content to the Tabhost * @param activity * @param tabHost * @param tabSpec * @param clss * @param args */ private static void AddTab(TabsViewPagerFragmentActivity activity, TabHost tabHost, TabHost.TabSpec tabSpec, TabInfo tabInfo) { // Attach a Tab view factory to the spec ImageView indicator = new ImageView(activity.getBaseContext()); indicator.setPadding(10, 10, 10, 10); indicator.setImageResource(R.drawable.tab_select_icon_selector); LinearLayout.LayoutParams lp = new LinearLayout.LayoutParams(LinearLayout.LayoutParams.WRAP_CONTENT, LinearLayout.LayoutParams.WRAP_CONTENT); lp.setMargins(10, 10, 10, 10); indicator.setLayoutParams(lp); tabSpec.setIndicator(indicator); tabSpec.setContent(activity.new TabFactory(activity)); tabHost.addTab(tabSpec); } /** (non-Javadoc) * @see android.widget.TabHost.OnTabChangeListener#onTabChanged(java.lang.String) */ public void onTabChanged(String tag) { //TabInfo newTab = this.mapTabInfo.get(tag); int pos = this.mTabHost.getCurrentTab(); this.mViewPager.setCurrentItem(pos); } /* (non-Javadoc) * @see android.support.v4.view.ViewPager.OnPageChangeListener#onPageScrolled(int, float, int) */ @Override public void onPageScrolled(int position, float positionOffset, int positionOffsetPixels) { // TODO Auto-generated method stub } /* (non-Javadoc) * @see android.support.v4.view.ViewPager.OnPageChangeListener#onPageSelected(int) */ @Override public void onPageSelected(int position) { // TODO Auto-generated method stub this.mTabHost.setCurrentTab(position); } /* (non-Javadoc) * @see android.support.v4.view.ViewPager.OnPageChangeListener#onPageScrollStateChanged(int) */ @Override public void onPageScrollStateChanged(int state) { // TODO Auto-generated method stub } How would one save the state of the TabHost and restore it in onResume? Any help would be very appreciated.

Read the article

Set button content in a label (custom control)

- by user1881207

Instead of voting negative this question, answer to tell me what's wrong! I want to set the Button Content in a label in the custom control, because when I use it, the Content property is not visible and the button is empty (no text). <Button x:Class="WpfApplication1.UserControl1" xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" xmlns:mc="http://schemas.openxmlformats.org/markup-compatibility/2006" xmlns:d="http://schemas.microsoft.com/expression/blend/2008" mc:Ignorable="d" d:DesignHeight="35" d:DesignWidth="273" Content="Button"> <Button.Template> <ControlTemplate> <Grid> <Rectangle Name="rGridBack" StrokeThickness="1"> <Rectangle.Fill> <LinearGradientBrush EndPoint="0.5,1" StartPoint="0.5,0"> <GradientStop Color="#FF4D4D4D" Offset="1" /> <GradientStop Color="#FF404040" Offset="0" /> </LinearGradientBrush> </Rectangle.Fill> <Rectangle.Stroke> <LinearGradientBrush EndPoint="0.5,1" StartPoint="0.5,0"> <GradientStop Color="#FF4F4F4F" Offset="0" /> <GradientStop Color="#FF5B5B5B" Offset="1" /> </LinearGradientBrush> </Rectangle.Stroke> </Rectangle> <Rectangle Fill="#FF1E1E1E" Margin="1,1,1,1" Name="rThickness" /> <Rectangle Margin="2,2,2,2" Name="rGridTop" StrokeThickness="1"> <Rectangle.Fill> <LinearGradientBrush EndPoint="0.5,1" StartPoint="0.5,0"> <GradientStop Color="#FF68686C" Offset="0" /> <GradientStop Color="#FF474747" Offset="1" /> </LinearGradientBrush> </Rectangle.Fill> <Rectangle.Stroke> <LinearGradientBrush EndPoint="0.5,1" StartPoint="0.5,0"> <GradientStop Color="#FF7F7F7F" Offset="0" /> <GradientStop Color="#FF575757" Offset="1" /> </LinearGradientBrush> </Rectangle.Stroke> </Rectangle>  <Label FontWeight="Normal" Foreground="White" HorizontalContentAlignment="Center" Name="tblckStep1Desc" Padding="0" VerticalContentAlignment="Center"> <Label.Effect> <DropShadowEffect BlurRadius="2" Color="Black" Direction="330" Opacity="0.7" ShadowDepth="1.5" /> </Label.Effect> </Label> </Grid> <ControlTemplate.Triggers> <Trigger Property="Button.Content" Value=""> <Setter Property="Content" TargetName="tblckStep1Desc"> </Setter> </Trigger> <Trigger Property="UIElement.IsMouseOver" Value="True"> <Setter Property="Shape.Fill" TargetName="rGridTop"> <Setter.Value> <LinearGradientBrush EndPoint="0.5,1" StartPoint="0.5,0"> <GradientStop Color="#FF838383" Offset="0" /> <GradientStop Color="#FF545454" Offset="1" /> </LinearGradientBrush> </Setter.Value> </Setter> <Setter Property="Shape.Stroke" TargetName="rGridTop"> <Setter.Value> <LinearGradientBrush EndPoint="0.5,1" StartPoint="0.5,0"> <GradientStop Color="#FF595959" Offset="1" /> <GradientStop Color="#FF929292" Offset="0" /> </LinearGradientBrush> </Setter.Value> </Setter> <Setter Property="Shape.Stroke" TargetName="rGridBack"> <Setter.Value> <LinearGradientBrush EndPoint="0.5,1" StartPoint="0.5,0"> <GradientStop Color="#FF414141" Offset="0" /> <GradientStop Color="#FF565656" Offset="1" /> </LinearGradientBrush> </Setter.Value> </Setter> <Setter Property="Shape.Fill" TargetName="rThickness"> <Setter.Value> <LinearGradientBrush EndPoint="0.5,1" StartPoint="0.5,0"> <GradientStop Color="#FF181818" Offset="1" /> <GradientStop Color="#FF181818" Offset="0" /> </LinearGradientBrush> </Setter.Value> </Setter> </Trigger> <Trigger Property="UIElement.IsEnabled" Value="False"> <Setter Property="Shape.Fill" TargetName="rGridTop"> <Setter.Value> <LinearGradientBrush EndPoint="0.5,1" StartPoint="0.5,0"> <GradientStop Color="#FF68686C" Offset="0" /> <GradientStop Color="#FF474747" Offset="1" /> </LinearGradientBrush> </Setter.Value> </Setter> <Setter Property="Shape.Stroke" TargetName="rGridTop"> <Setter.Value> <LinearGradientBrush EndPoint="0.5,1" StartPoint="0.5,0"> <GradientStop Color="#FF7F7F7F" Offset="0" /> <GradientStop Color="#FF575757" Offset="1" /> </LinearGradientBrush> </Setter.Value> </Setter> <Setter Property="Shape.Stroke" TargetName="rGridBack"> <Setter.Value> <LinearGradientBrush EndPoint="0.5,1" StartPoint="0.5,0"> <GradientStop Color="#FF4F4F4F" Offset="0" /> <GradientStop Color="#FF5B5B5B" Offset="1" /> </LinearGradientBrush> </Setter.Value> </Setter> <Setter Property="Shape.Fill" TargetName="rThickness"> <Setter.Value> <LinearGradientBrush EndPoint="0.5,1" StartPoint="0.5,0"> <GradientStop Color="#FF1E1E1E" Offset="1" /> <GradientStop Color="#FF1E1E1E" Offset="0" /> </LinearGradientBrush> </Setter.Value> </Setter> <Setter Property="Control.Foreground" TargetName="tblckStep1Desc"> <Setter.Value> <LinearGradientBrush EndPoint="0.5,1" StartPoint="0.5,0"> <GradientStop Color="#FF898989" Offset="1" /> <GradientStop Color="#FF898989" Offset="0" /> </LinearGradientBrush> </Setter.Value> </Setter> </Trigger> <Trigger Property="ButtonBase.IsPressed" Value="True"> <Setter Property="Shape.Fill" TargetName="rGridTop"> <Setter.Value> <LinearGradientBrush EndPoint="0.5,1" StartPoint="0.5,0"> <GradientStop Color="#FF313131" Offset="1" /> <GradientStop Color="#FF2E2E2E" Offset="0" /> </LinearGradientBrush> </Setter.Value> </Setter> <Setter Property="Shape.Stroke" TargetName="rGridTop"> <Setter.Value> <LinearGradientBrush EndPoint="0.5,1" StartPoint="0.5,0"> <GradientStop Color="#FF1F1F1F" Offset="1" /> <GradientStop Color="#FF1F1F1F" Offset="0" /> </LinearGradientBrush> </Setter.Value> </Setter> <Setter Property="Shape.Stroke" TargetName="rGridBack"> <Setter.Value> <LinearGradientBrush EndPoint="0.5,1" StartPoint="0.5,0"> <GradientStop Color="#FF414141" Offset="1" /> <GradientStop Color="#FF565656" Offset="0" /> </LinearGradientBrush> </Setter.Value> </Setter> <Setter Property="Shape.Fill" TargetName="rThickness"> <Setter.Value> <LinearGradientBrush EndPoint="0.5,1" StartPoint="0.5,0"> <GradientStop Color="#FF0C0C0C" Offset="1" /> <GradientStop Color="#FF0C0C0C" Offset="0" /> </LinearGradientBrush> </Setter.Value> </Setter> </Trigger> </ControlTemplate.Triggers> </ControlTemplate> </Button.Template> The button is based on Adobe CS5 suite on dialog forms, because a lot of code.

Read the article

Facebook android app keeps crashing even though there are no errors in my code. Why?

- by user1554479

If you import the facebook SDK library, the code works (ignore the deprecated methods for now lol) and there are no errors or warnings. However, when I run my facebook app on my Android 2.2 or 4.2 emulator, the app crashes either upon opening or after the log on screen. Why? Is it because I'm not implementing Async Task? If so, how does that work? Here's my code: package com.sara.facebookappl; import java.io.IOException; import java.net.MalformedURLException; import java.net.URL; import org.json.JSONException; import org.json.JSONObject; import android.app.Activity; import android.content.Intent; import android.content.SharedPreferences; import android.content.SharedPreferences.Editor; import android.os.Bundle; import android.os.StrictMode; import android.view.Menu; import android.view.View; import android.view.View.OnClickListener; import android.widget.Button; import android.widget.ImageView; import android.widget.TextView; import android.widget.Toast; import com.facebook.android.DialogError; import com.facebook.android.Facebook; import com.facebook.android.Facebook.DialogListener; import com.facebook.android.FacebookError; import com.facebook.android.Util; public class MainActivity extends Activity implements OnClickListener, DialogListener { Facebook fb; ImageView button; SharedPreferences sp; TextView welcome; Button post; @SuppressWarnings("deprecation") @Override protected void onCreate(Bundle savedInstanceState) { super.onCreate(savedInstanceState); setContentView(R.layout.activity_main); post=(Button)findViewById(R.id.button1); String APP_ID = getString(R.string.APP_ID); fb= new Facebook(APP_ID); sp =getPreferences(MODE_PRIVATE); String access_token=sp.getString("access_token", null); long expires=sp.getLong("access_expires", 0); if (access_token !=null) { fb.setAccessToken(access_token); } if(expires !=0) { fb.setAccessExpires(expires); } button=(ImageView)findViewById(R.id.login); button.setOnClickListener((OnClickListener) this); updateButtonImage(); } @SuppressWarnings("deprecation") private void updateButtonImage() { // TODO Auto-generated method stub post.setVisibility(Button.VISIBLE); button.setImageResource(R.drawable.com_facebook_loginbutton_blue); //logout button if (fb.isSessionValid()) { button.setImageResource(R.drawable.com_facebook_loginbutton_blue); // ^logout button JSONObject obj=null; URL img_url =null; try { String jsonUser= fb.request("me"); obj = Util.parseJson(jsonUser); String id=obj.optString("id"); String name = obj.optString("name"); welcome.setText("Welcome, " + name); }catch(FacebookError e) { e.printStackTrace(); }catch (JSONException e) { e.printStackTrace(); }catch (MalformedURLException e) { e.printStackTrace(); }catch (IOException e) { e.printStackTrace(); } }else { post.setVisibility(Button.VISIBLE); button.setImageResource(R.drawable.com_facebook_loginbutton_blue); } } @SuppressWarnings("deprecation") public void buttonClicks(View v) { switch (v.getId()) { case R.id.button1: //post Bundle params= new Bundle(); params.putString("name", "User X"); params.putString("caption", "Rating"); params.putString("description", "User X Rated"); params.putString("link", "http://..."); fb.dialog(MainActivity.this, "feed", params, new Facebook.DialogListener() { @Override public void onFacebookError(FacebookError e) { // TODO Auto-generated method stub } @Override public void onError(DialogError e) { // TODO Auto-generated method stub } @Override public void onComplete(Bundle values) { // TODO Auto-generated method stub } @Override public void onCancel() { // TODO Auto-generated method stub } }); break; } } @SuppressWarnings("deprecation") public void onClick(View v) { if(fb.isSessionValid()) { try { fb.logout(getApplicationContext()); updateButtonImage(); //button will close our our session }catch(MalformedURLException e) { e.printStackTrace(); } catch(IOException e) { e.printStackTrace(); } }else{ //login into facebook fb.authorize(MainActivity.this, new String[] {"email"}, new Facebook.DialogListener() { @Override public void onFacebookError(FacebookError e) { // TODO Auto-generated method stub Toast.makeText(MainActivity.this, "fbError", Toast.LENGTH_SHORT).show(); } @Override public void onError(DialogError e) { // TODO Auto-generated method stub Toast.makeText(MainActivity.this, "onError", Toast.LENGTH_SHORT).show(); } @Override public void onComplete(Bundle values) { // TODO Auto-generated method stub Editor editor=sp.edit(); editor.putString("access_token", fb.getAccessToken()); editor.putLong("access_expires", fb.getAccessExpires()); editor.commit(); updateButtonImage(); } @Override public void onCancel() { // TODO Auto-generated method stub Toast.makeText(MainActivity.this, "onCancel", Toast.LENGTH_SHORT).show(); } }); } } @Override public boolean onCreateOptionsMenu(Menu menu) { // Inflate the menu; this adds items to the action bar if it is present. getMenuInflater().inflate(R.menu.activity_main, menu); return true; } @SuppressWarnings("deprecation") @Override protected void onActivityResult(int requestCode, int resultCode, Intent data) { super.onActivityResult(requestCode, resultCode, data); fb.authorizeCallback(requestCode, resultCode, data); } @Override public void onComplete(Bundle values) { // TODO Auto-generated method stub } @Override public void onFacebookError(FacebookError e) { // TODO Auto-generated method stub } @Override public void onError(DialogError e) { // TODO Auto-generated method stub } @Override public void onCancel() { // TODO Auto-generated method stub } } LogCat Errors: 12-16 04:56:59.070: E/AndroidRuntime(822): FATAL EXCEPTION: main 12-16 04:56:59.070: E/AndroidRuntime(822): java.lang.RuntimeException: Unable to start activity ComponentInfo{com.sara.facebookappl/com.sara.facebookappl.MainActivity}: android.os.NetworkOnMainThreadException 12-16 04:56:59.070: E/AndroidRuntime(822): at android.app.ActivityThread.performLaunchActivity(ActivityThread.java:2180) 12-16 04:56:59.070: E/AndroidRuntime(822): at android.app.ActivityThread.handleLaunchActivity(ActivityThread.java:2230) 12-16 04:56:59.070: E/AndroidRuntime(822): at android.app.ActivityThread.access$600(ActivityThread.java:141) 12-16 04:56:59.070: E/AndroidRuntime(822): at android.app.ActivityThread$H.handleMessage(ActivityThread.java:1234) 12-16 04:56:59.070: E/AndroidRuntime(822): at android.os.Handler.dispatchMessage(Handler.java:99) 12-16 04:56:59.070: E/AndroidRuntime(822): at android.os.Looper.loop(Looper.java:137) 12-16 04:56:59.070: E/AndroidRuntime(822): at android.app.ActivityThread.main(ActivityThread.java:5039) 12-16 04:56:59.070: E/AndroidRuntime(822): at java.lang.reflect.Method.invokeNative(Native Method) 12-16 04:56:59.070: E/AndroidRuntime(822): at java.lang.reflect.Method.invoke(Method.java:511) 12-16 04:56:59.070: E/AndroidRuntime(822): at com.android.internal.os.ZygoteInit$MethodAndArgsCaller.run(ZygoteInit.java:793) 12-16 04:56:59.070: E/AndroidRuntime(822): at com.android.internal.os.ZygoteInit.main(ZygoteInit.java:560) 12-16 04:56:59.070: E/AndroidRuntime(822): at dalvik.system.NativeStart.main(Native Method) 12-16 04:56:59.070: E/AndroidRuntime(822): Caused by: android.os.NetworkOnMainThreadException 12-16 04:56:59.070: E/AndroidRuntime(822): at android.os.StrictMode$AndroidBlockGuardPolicy.onNetwork(StrictMode.java:1117) 12-16 04:56:59.070: E/AndroidRuntime(822): at java.net.InetAddress.lookupHostByName(InetAddress.java:385) 12-16 04:56:59.070: E/AndroidRuntime(822): at java.net.InetAddress.getAllByNameImpl(InetAddress.java:236) 12-16 04:56:59.070: E/AndroidRuntime(822): at java.net.InetAddress.getAllByName(InetAddress.java:214) 12-16 04:56:59.070: E/AndroidRuntime(822): at libcore.net.http.HttpConnection.(HttpConnection.java:70) 12-16 04:56:59.070: E/AndroidRuntime(822): at libcore.net.http.HttpConnection.(HttpConnection.java:50) 12-16 04:56:59.070: E/AndroidRuntime(822): at libcore.net.http.HttpConnection$Address.connect(HttpConnection.java:340) 12-16 04:56:59.070: E/AndroidRuntime(822): at libcore.net.http.HttpConnectionPool.get(HttpConnectionPool.java:87) 12-16 04:56:59.070: E/AndroidRuntime(822): at libcore.net.http.HttpConnection.connect(HttpConnection.java:128) 12-16 04:56:59.070: E/AndroidRuntime(822): at libcore.net.http.HttpEngine.openSocketConnection(HttpEngine.java:316) 12-16 04:56:59.070: E/AndroidRuntime(822): at libcore.net.http.HttpsURLConnectionImpl$HttpsEngine.makeSslConnection(HttpsURLConnectionImpl.java:461) 12-16 04:56:59.070: E/AndroidRuntime(822): at libcore.net.http.HttpsURLConnectionImpl$HttpsEngine.connect(HttpsURLConnectionImpl.java:433) 12-16 04:56:59.070: E/AndroidRuntime(822): at libcore.net.http.HttpEngine.sendSocketRequest(HttpEngine.java:290) 12-16 04:56:59.070: E/AndroidRuntime(822): at libcore.net.http.HttpEngine.sendRequest(HttpEngine.java:240) 12-16 04:56:59.070: E/AndroidRuntime(822): at libcore.net.http.HttpURLConnectionImpl.getResponse(HttpURLConnectionImpl.java:282) 12-16 04:56:59.070: E/AndroidRuntime(822): at libcore.net.http.HttpURLConnectionImpl.getInputStream(HttpURLConnectionImpl.java:177) 12-16 04:56:59.070: E/AndroidRuntime(822): at libcore.net.http.HttpsURLConnectionImpl.getInputStream(HttpsURLConnectionImpl.java:271) 12-16 04:56:59.070: E/AndroidRuntime(822): at com.facebook.android.Util.openUrl(Util.java:219) 12-16 04:56:59.070: E/AndroidRuntime(822): at com.facebook.android.Facebook.requestImpl(Facebook.java:806) 12-16 04:56:59.070: E/AndroidRuntime(822): at com.facebook.android.Facebook.request(Facebook.java:732) 12-16 04:56:59.070: E/AndroidRuntime(822): at com.sara.facebookappl.MainActivity.updateButtonImage(MainActivity.java:83) 12-16 04:56:59.070: E/AndroidRuntime(822): at com.sara.facebookappl.MainActivity.onCreate(MainActivity.java:63) 12-16 04:56:59.070: E/AndroidRuntime(822): at android.app.Activity.performCreate(Activity.java:5104) 12-16 04:56:59.070: E/AndroidRuntime(822): at android.app.Instrumentation.callActivityOnCreate(Instrumentation.java:1080) 12-16 04:56:59.070: E/AndroidRuntime(822): at android.app.ActivityThread.performLaunchActivity(ActivityThread.java:2144) 12-16 04:56:59.070: E/AndroidRuntime(822): ... 11 more 12-16 04:56:59.090: D/dalvikvm(822): GC_CONCURRENT freed 150K, 9% free 2723K/2988K, paused 7ms+58ms, total 239ms

Read the article

Installation error: INSTALL_FAILED_OLDER_SDK in eclipse

- by user3014909

I have an unexpe`ted problem with my Android project. I have a real android device with ice_cream sandwich installed. My app was working fine during the development but after I added a class to the project, I got an error: Installation error: INSTALL_FAILED_OLDER_SDK The problem is that everything is good in the manifest file. The minSdkversion is 8. Here is my manifest file: <?xml version="1.0" encoding="utf-8"?> <manifest xmlns:android="http://schemas.android.com/apk/res/android" package="zabolotnii.pavel.timer" android:versionCode="1" android:versionName="1.0" > <uses-sdk android:minSdkVersion="8" android:targetSdkVersion="18 " /> <application android:allowBackup="true" android:icon="@drawable/ic_launcher" android:label="@string/app_name" android:theme="@style/AppTheme" > <activity android:name="zabolotnii.pavel.timer.TimerActivity" android:label="@string/app_name" > <intent-filter> <action android:name="android.intent.action.MAIN" /> <category android:name="android.intent.category.LAUNCHER" /> </intent-filter> </activity> </application> </manifest> I don't know, if there is any need to attach the new class ,but I didn't any changes to other code that should led to this error: package zabolotnii.pavel.timer; import android.app.AlertDialog; import android.content.Context; import android.content.DialogInterface; import android.graphics.Paint; import android.graphics.Point; import android.graphics.Rect; import android.graphics.drawable.Drawable; import android.os.Environment; import android.util.DisplayMetrics; import android.util.TypedValue; import android.view.*; import android.widget.*; import java.io.File; import java.io.FilenameFilter; import java.util.*; public class OpenFileDialog extends AlertDialog.Builder { private String currentPath = Environment.getExternalStorageDirectory().getPath(); private List<File> files = new ArrayList<File>(); private TextView title; private ListView listView; private FilenameFilter filenameFilter; private int selectedIndex = -1; private OpenDialogListener listener; private Drawable folderIcon; private Drawable fileIcon; private String accessDeniedMessage; public interface OpenDialogListener { public void OnSelectedFile(String fileName); } private class FileAdapter extends ArrayAdapter<File> { public FileAdapter(Context context, List<File> files) { super(context, android.R.layout.simple_list_item_1, files); } @Override public View getView(int position, View convertView, ViewGroup parent) { TextView view = (TextView) super.getView(position, convertView, parent); File file = getItem(position); if (view != null) { view.setText(file.getName()); if (file.isDirectory()) { setDrawable(view, folderIcon); } else { setDrawable(view, fileIcon); if (selectedIndex == position) view.setBackgroundColor(getContext().getResources().getColor(android.R.color.holo_blue_dark)); else view.setBackgroundColor(getContext().getResources().getColor(android.R.color.transparent)); } } return view; } private void setDrawable(TextView view, Drawable drawable) { if (view != null) { if (drawable != null) { drawable.setBounds(0, 0, 60, 60); view.setCompoundDrawables(drawable, null, null, null); } else { view.setCompoundDrawables(null, null, null, null); } } } } public OpenFileDialog(Context context) { super(context); title = createTitle(context); changeTitle(); LinearLayout linearLayout = createMainLayout(context); linearLayout.addView(createBackItem(context)); listView = createListView(context); linearLayout.addView(listView); setCustomTitle(title) .setView(linearLayout) .setPositiveButton(android.R.string.ok, new DialogInterface.OnClickListener() { @Override public void onClick(DialogInterface dialog, int which) { if (selectedIndex > -1 && listener != null) { listener.OnSelectedFile(listView.getItemAtPosition(selectedIndex).toString()); } } }) .setNegativeButton(android.R.string.cancel, null); } @Override public AlertDialog show() { files.addAll(getFiles(currentPath)); listView.setAdapter(new FileAdapter(getContext(), files)); return super.show(); } public OpenFileDialog setFilter(final String filter) { filenameFilter = new FilenameFilter() { @Override public boolean accept(File file, String fileName) { File tempFile = new File(String.format("%s/%s", file.getPath(), fileName)); if (tempFile.isFile()) return tempFile.getName().matches(filter); return true; } }; return this; } public OpenFileDialog setOpenDialogListener(OpenDialogListener listener) { this.listener = listener; return this; } public OpenFileDialog setFolderIcon(Drawable drawable) { this.folderIcon = drawable; return this; } public OpenFileDialog setFileIcon(Drawable drawable) { this.fileIcon = drawable; return this; } public OpenFileDialog setAccessDeniedMessage(String message) { this.accessDeniedMessage = message; return this; } private static Display getDefaultDisplay(Context context) { return ((WindowManager) context.getSystemService(Context.WINDOW_SERVICE)).getDefaultDisplay(); } private static Point getScreenSize(Context context) { Point screeSize = new Point(); getDefaultDisplay(context).getSize(screeSize); return screeSize; } private static int getLinearLayoutMinHeight(Context context) { return getScreenSize(context).y; } private LinearLayout createMainLayout(Context context) { LinearLayout linearLayout = new LinearLayout(context); linearLayout.setOrientation(LinearLayout.VERTICAL); linearLayout.setMinimumHeight(getLinearLayoutMinHeight(context)); return linearLayout; } private int getItemHeight(Context context) { TypedValue value = new TypedValue(); DisplayMetrics metrics = new DisplayMetrics(); context.getTheme().resolveAttribute(android.R.attr.listPreferredItemHeightSmall, value, true); getDefaultDisplay(context).getMetrics(metrics); return (int) TypedValue.complexToDimension(value.data, metrics); } private TextView createTextView(Context context, int style) { TextView textView = new TextView(context); textView.setTextAppearance(context, style); int itemHeight = getItemHeight(context); textView.setLayoutParams(new ViewGroup.LayoutParams(ViewGroup.LayoutParams.MATCH_PARENT, itemHeight)); textView.setMinHeight(itemHeight); textView.setGravity(Gravity.CENTER_VERTICAL); textView.setPadding(15, 0, 0, 0); return textView; } private TextView createTitle(Context context) { TextView textView = createTextView(context, android.R.style.TextAppearance_DeviceDefault_DialogWindowTitle); return textView; } private TextView createBackItem(Context context) { TextView textView = createTextView(context, android.R.style.TextAppearance_DeviceDefault_Small); Drawable drawable = getContext().getResources().getDrawable(android.R.drawable.ic_menu_directions); drawable.setBounds(0, 0, 60, 60); textView.setCompoundDrawables(drawable, null, null, null); textView.setLayoutParams(new ViewGroup.LayoutParams(ViewGroup.LayoutParams.MATCH_PARENT, ViewGroup.LayoutParams.WRAP_CONTENT)); textView.setOnClickListener(new View.OnClickListener() { @Override public void onClick(View view) { File file = new File(currentPath); File parentDirectory = file.getParentFile(); if (parentDirectory != null) { currentPath = parentDirectory.getPath(); RebuildFiles(((FileAdapter) listView.getAdapter())); } } }); return textView; } public int getTextWidth(String text, Paint paint) { Rect bounds = new Rect(); paint.getTextBounds(text, 0, text.length(), bounds); return bounds.left + bounds.width() + 80; } private void changeTitle() { String titleText = currentPath; int screenWidth = getScreenSize(getContext()).x; int maxWidth = (int) (screenWidth * 0.99); if (getTextWidth(titleText, title.getPaint()) > maxWidth) { while (getTextWidth("..." + titleText, title.getPaint()) > maxWidth) { int start = titleText.indexOf("/", 2); if (start > 0) titleText = titleText.substring(start); else titleText = titleText.substring(2); } title.setText("..." + titleText); } else { title.setText(titleText); } } private List<File> getFiles(String directoryPath) { File directory = new File(directoryPath); List<File> fileList = Arrays.asList(directory.listFiles(filenameFilter)); Collections.sort(fileList, new Comparator<File>() { @Override public int compare(File file, File file2) { if (file.isDirectory() && file2.isFile()) return -1; else if (file.isFile() && file2.isDirectory()) return 1; else return file.getPath().compareTo(file2.getPath()); } }); return fileList; } private void RebuildFiles(ArrayAdapter<File> adapter) { try { List<File> fileList = getFiles(currentPath); files.clear(); selectedIndex = -1; files.addAll(fileList); adapter.notifyDataSetChanged(); changeTitle(); } catch (NullPointerException e) { String message = getContext().getResources().getString(android.R.string.unknownName); if (!accessDeniedMessage.equals("")) message = accessDeniedMessage; Toast.makeText(getContext(), message, Toast.LENGTH_SHORT).show(); } } private ListView createListView(Context context) { ListView listView = new ListView(context); listView.setOnItemClickListener(new AdapterView.OnItemClickListener() { @Override public void onItemClick(AdapterView<?> adapterView, View view, int index, long l) { final ArrayAdapter<File> adapter = (FileAdapter) adapterView.getAdapter(); File file = adapter.getItem(index); if (file.isDirectory()) { currentPath = file.getPath(); RebuildFiles(adapter); } else { if (index != selectedIndex) selectedIndex = index; else selectedIndex = -1; adapter.notifyDataSetChanged(); } } }); return listView; } }

Search Results

Search found 13516 results on 541 pages for 'common dialog'.

Page 537/541 | < Previous Page | 533 534 535 536 537 538 539 540 541 | Next Page >

- by Rakeka

- by Bill Graziano

- by Shay Shmeltzer

- by sina

- by Eibis

- by Michael B. McLaughlin

- by nikolaosk

- by Alois Kraus

- by Robert

- by SGWellens

- by SGWellens

- by Jason R

- by chaoskreator

- by kongkea

- by ikurtz

- by Danny

- by Tony O'Keeffe

- by Whospal

- by thiagolee

- by Emil Adz

- by user1881207

- by user1554479

- by user3014909

< Previous Page | 533 534 535 536 537 538 539 540 541 | Next Page >