Search Results

Search found 21589 results on 864 pages for 'primary key'.

Page 537/864 | < Previous Page | 533 534 535 536 537 538 539 540 541 542 543 544  | Next Page >

• SAN Replication for Fault tolerance using EVA4400

  - by Sergei

  Hi Everyone, I hope that someone would point me in the correct direction - it looks like I have no enough konwledge in the subject and timeframes are too tight for me to explore different scenarios in depth.. We have two datacenters few miles away from each other connected by 100 Mbps link.Each datacenter will have 5 BL490 blades with ESX Standard hosting about 50 VMs. Eac hsite has HP eva4400 SAN with SAN replication set up.VC is going to be in the first datacenter and both datacenter are networked. SAN Replication is block level so it seems like I cannot just replicate changes but all writes would have to be replicated.This should not be a problem as link can sustain about 1.8 TB a dayand data can be buffered. I am having trouble however visioning how recovery would work in this case.We don't need instant recovery , I would say 4 hours recovery time is accepted so fancy automatic SRM like DR scenario would not be easily accepted due to the financial reasons, however any comments are welcomed. Current idea is following: replicate LUNs from primary site to the secondary.When disaster strikes, IT personnel switches on ESX hosts on the remote side and connects replicated LUNS to them, then registers VMs and changes IP address. I understand that this seems like horribly manual process and I almost sure I have missed some obvious pitfalls here. Could someone let me know what direction should I go?An articles regarding the subject? This is a brand new setup and we would rather build up basic recovery process and scale it later.I just need to have a right direction to allow for such scalability. Thank you very much in advance!

  Read the article

• SQL Server 2008 Logshipping not Restoring

  - by Nai

  I am getting the following errors during the restore part of the Logshipping process on my secondary server: 2010-04-01 10:00:01.85 Error: The file 'F:\UK_20100327090001.trn' is too recent to apply to the secondary database 'UK_Backup'.(Microsoft.SqlServer.Management.LogShipping) 2010-04-01 10:00:01.85 Error: The log in this backup set begins at LSN 55408000007387500001, which is too recent to apply to the database. An earlier log backup that includes LSN 55147000001788900001 can be restored. RESTORE LOG is terminating abnormally.(.Net SqlClient Data Provider) 2010-04-01 10:00:01.87 Searching for an older log backup file. Secondary Database: 'UK_Backup' 2010-04-01 10:00:01.90 Skipped log backup file. Secondary DB: 'UK_Backup', File: 'F:\UK_20100324090000.trn' 2010-04-01 10:00:01.93 Error: Could not find a log backup file that could be applied to secondary database 'UK_Backup'.(Microsoft.SqlServer.Management.LogShipping) 2010-04-01 10:00:01.93 Deleting old log backup files. Primary Database: 'UK' 2010-04-01 10:00:01.96 The restore operation completed with errors. Secondary ID: 'c066bb63-930c-4b73-861c-f59f0a38c12c' It was happily humming along until I checked it this morning. Some additional details. In the Logshipping folder, there is one file UK_20100324090001.trn dated on the 2009-3-24. The next most recent .trn file is the UK_20100374090001.trn which is the file that was applied during the restore. Why is there an older trn file seemingly on it's own? How can I fix this problem? It'll be a real pain to restart the entire logshipping process. x_x

  Read the article

• JBossMQ - Clustered Queues/NameNotFoundException: QueueConnectionFactory error

  - by mfarver

  I am trying to get an application working on a JBoss Cluster. It uses Queues internally, and the developer claims that it should work correctly in a clustered environment. I have jbossmq setup as a ha-singleton on the cluster. The application works correctly on whichever node currently is running the queue, but fails on the other nodes with a: "javax.naming.NameNotFoundException: QueueConnectionFactory not bound" error. I can look at JNDIview from the jmx-console and see that indeed the QueueConnectionFactory class only appears on the primary node in the Global context. Is there a way to see the Cluster's JNDI listing instead of each server? The steps I took from a default Jboss 4.2.3.GA installation were to use the "all" configuration. Then removed /server/all/deploy/hsqldb-ds.xml and /deploy-hasingleton/jms/hsqldb-jdbc2-service.xml, copying the example/jms/mysq-jdbc2-service.xml file into its place (editing that file to use DefaultDS instead of MySqlDS). Finally I created a mysql-ds.xml file in the deploy directory pointing "DefaultDS" at an empty database. I created a -services.xml file in the deploy directory with the queue definition. like the one below: <server> <mbean code="org.jboss.mq.server.jmx.Queue" name="jboss.mq.destination:service=Queue,name=myfirstqueue"> <depends optional-attribute-name="DestinationManager"> jboss.mq:service=DestinationManager </depends> </mbean> </server> All of the other cluster features of working, the servers list each other in the view, and sessions are replicating back and forth. The JBoss documentation is somewhat light in this area, is there another setting I might have missed? Or is this likely to be a code issue (is there different code to do a JNDI lookup in a clusted environment?) Thanks

  Read the article

• Windows Authentication behaves oddly when VPN'd

  - by Dan F

  Hi all We've got a few apps that rely on windows authentication - a couple of web apps with AD auth turned on and we usually connect to our SQL servers with windows auth. This normally runs without a hitch. It doesn't work so well if we're VPN'd to a client site though. SSMS Opening SSMS normally from the start menu, then picking a server that normally accepts windows auth, results in a message saying: Login failed. The login is from an untrusted domain and cannot be used with Windows authentication. (.Net SqlClient Data Provider) If I drop to a command prompt and use runas /user:domain\user to launch SSMS I can successfully windows auth to our SQL server instances with that ssms process. If I look in task manager, both copies of ssms.exe (start menu vs runas) have the same user, and I can see no discernible differences between the processes in procexp. AD Auth websites If I open IE and browse to any of our websites that require an authenticated windows user, I get the "who are you" prompt, and that dialog thinks I'm whoever the VPN user is. I can click "Use another account" and authenticate that way though. Outlook Even Outlook prompts for a username when we are VPN'd! It's affecting our Win7 and Vista machines. It's been a while since we had an XP box, but I don't recall having this issue on XP for what it's worth. The VPN connections are just using the built in windows VPN connections, they're not fancy cisco VPNs or anything of that nature. Does anyone know how to tell windows that I'd like to be my normal old primary domain user rather than the VPN user when authenticating to resources in our domain? Heck, I'd be happy with a solution that prompted me with the "who are you" if I was trying to access windows auth requiring resources on the client's VPN. Thanks! Apologies if this is more a superuser question, I wasn't sure which site it best suited. It's about networking and infrastructure and plagues all of our developers here, so I hope it's a serverfault Q.

  Read the article

• Chunking large rsync transfers?

  - by Gabe Martin-Dempesy

  We use rsync to update a mirror of our primary file server to an off-site colocated backup server. One of the issues we currently have is that our file server has 1TB of mostly smaller files (in the 10-100kb range), and when we're transferring this much data, we often end up with the connection being dropped several hours into the transfer. Rsync doesn't have a resume/retry feature that simply reconnects to the server to pickup where it left off -- you need to go through the file comparison process, which ends up being very length with the amount of files we have. The solution that's recommended to get around is to split up your large rsync transfer into a series of smaller transfers. I've figured the best way to do this is by first letter of the top-level directory names, which doesn't give us a perfectly even distribution, but is good enough. I'd like to confirm if my methodology for doing this is sane, or if there's a more simple way to accomplish the goal. To do this, I iterate through A-Z, a-z, 0-9 to pick a one character $prefix. Initially I was thinking of just running rsync -av --delete --delete-excluded --exclude "*.mp3" "src/$prefix*" dest/ (--exclude "*.mp3" is just an example, as we have a more lengthy exclude list for removing things like temporary files) The problem with this is that any top-level directories in dest/ that are no longer present present on src will not get picked up by --delete. To get around this, I'm instead trying the following: rsync \ --filter 'S /$prefix*' \ --filter 'R /$prefix*' \ --filter 'H /*' \ --filter 'P /*' \ -av --delete --delete-excluded --exclude "*.mp3" src/ dest/ I'm using the show and hide over include and exclude, because otherwise the --delete-excluded will delete anything that doesn't match $prefix. Is this the most effective way of splitting the rsync into smaller chunks? Is there a more effective tool, or a flag that I've missed, that might make this more simple?

  Read the article

• Windows 7 install detects SSD but doesn't list it to install to

  - by Mohamed Meligy

  I'm having quite a weird problem when trying to install Windows 7 SP1 on a new Corsair Force Series 3 SSD to replace a failing HDD in my wife's laptop. When I boot to Windows install, it shows that I have no disks to install to, and tells me to find it a driver to any custom disks I may have. When I go to repair option on the first install window, and then open command prompt Window, I can see the disk using diskpart, and can partition it and format partitions, and then later access them from command prompt and copy files to them. After creating partitions, clicking the "browse" button in Windows install screen that shows no disks available to install Windows to, does show the partitions created by diskpart! So, it does detect the disk and partitions, but refuses to list them as options to install to. People on the Interwebs seem to suggest that just running diskpart "clean" solved the issue for most people, just creating an "active" "primary" partition is al most tutorials suggest. Both got me only as far as described above. The BIOS doesn't have RAID option, changing between "ATA" and "AHCI" (the only available options) didn't make any difference. Might be worth mentioning that this is on a laptop that has Sata III controller for main drive (which I connected the Sata3 SSD to), and Sata II for DVD (which I used for Windows install media). That's what googling brings at least (DELL XPS 15 L502). Any ideas? . Update: The SSD is 460 GB. I tried setting it all as one partition and creating 70-90 GB partition as well (NTFS). More importantly, Windows doesn't list the partition as one it cannot install to (which it does with disks in general when they are small for example). What happens here is different. It doesn't list anything at all. It shows empty list of drives.

  Read the article

• How do you handle authentication across domains?

  - by William Ratcliff

  I'm trying to save users of our services from having to have multiple accounts/passwords. I'm in a large organization and there's one group that handles part of user authentication for users who are from outside the facility (primarily for administrative functions). They store a secure cookie to establish a session and communicate only via HTTPS via the browser. Sessions expire either through: 1) explicit logout of the user 2) Inactivity 3) Browser closes My team is trying to write a web application to help users analyze data that they've taken (or are currently taking) while at our facility. We need to determine if a user is 1) authenticated 2) Some identifier for that user so we can store state for them (what analysis they are working on, etc.) So, the problem is how do you authenticate across domains (the authentication server for the other application lives in a border region between public and private--we will live in the public region). We have come up with some scenarios and I'd like advice about what is best practice, or if there is one we haven't considered. Let's start with the case where the user is authenticated with the authentication server. 1) The authentication server leaves a public cookie in the browser with their primary key for a user. If this is deemed sensitive, they encrypt it on their server and we have the key to decrypt it on our server. When the user visits our site, we check for this public cookie. We extract the user_id and use a public api for the authentication server to request if the user is logged in. If they are, they send us a response with: response={ userid :we can then map this to our own user ids. If necessary, we can request additional information such as email-address/display name once (to notify them if long running jobs are done, or to share results with other people, like with google_docs). account_is_active:Make sure that the account is still valid session_is_active: Is their session still active? If we query this for a valid user, this will have a side effect that we will reset the last_time_session_activated value and thus prolong their session with the authentication server last_time_session_activated: let us know how much time they have left ip_address_session_started_from:make sure the person at our site is coming from the same ip as they started the session at } Given this response, we either accept them as authenticated and move on with our app, or redirect them to the login page for the authentication server (question: if we give an encrypted portion of the response (signed by us) with the page to redirect them to, do we open any gaping security holes in the authentication server)? The flaw that we've found with this is that if the user visits evilsite.com and they look at the session cookie and send a query to the public api of the authentication server, they can keep the session alive and if our original user leaves the machine without logging out, then the next user will be able to access their session (this was possible before, but having the session alive eternally makes this worse). 2) The authentication server redirects all requests made to our domain to us and we send responses back through them to the user. Essentially, they act as a proxy. The advantage of this is that we can handshake with the authentication server, so it's safe to be trusted with the email address/name of the user and they don't have to reenter it So, if the user tries to go to: authentication_site/mysite_page1 they are redirected to mysite. Which would you choose, or is there a better way? The goal is to minimize the "Yet Another Password/Yet another username" problem... Thanks!!!!

  Read the article

• likewise-open and samba as pdc

  - by Knight Samar

  Hi, We have successfully implemented a Samba Primary Domain Controller for a hybrid Windows-Linux environment. So now I am setting up dual-boot clients with Windows XP and Ubuntu 9.10. Windows XP can be easily added to the Samba Domain. Everything is manageable. No worries. But when I try using likewise-open 4.1 to add the Ubuntu 9.10 to the samba domain, it cannot locate the domain controller. domainjoin-cli --loglevel verbose join MYDOMAIN root Error: Unable to resolve DC name [code 0x00080026] Resolving 'MYDOMAIN' failed. Check that the domain name is correctly entered. Also check that your DNS server is reachable, and that your system is configured to use DNS in nsswitch. I even tried mydomain.com variations but to no avail. What am I missing ? I read up a document on MSDN wherein it says that the Domain Controller creates some SRV records in the DNS server. I guess, I don't have them on my BIND. Do you think that is the problem ? If yes, can anyone please point out how and what SRV records need to be added. Thanks.

  Read the article

• ISA Server 2006 SSL Certificate Dilemma

  - by JohnyD

  I'm making so great headway in offering our services over https with help from a Go Daddy certificate, later to be upgraded to Thawte SSL123 certs. But, I've just run into one whopper of a problem. Here's my setup: I run an ISA 2006 firewall. Our web services are distributed over 2 servers. One is Windows 2000 (www.domain.com) and the other is Windows 2003 (services.domain.com). So, I'll need to purchase 2 certs for both www and services, import them into IIS6 on their respective machines, then export them with the primary key (making sure to Include all certificates in the certification path if possible... that had me stumped for a while), and then to finally import them into ISA's local computer Personal store. The problem I've just run into is that I have separate firewall rules for services.domain.com and www.domain.com... because requests need to be forwarded to different web servers. Each of these firewall rules use the same httplistener. I have just found out that you can only use 1 certificate per httplistener. To make matters worse you can only have a single httplistener per ip / port. Is this correct? I can only use a single certificate for a single ip address? This would seem to be a severe limitation. Am I wrong? If I'm not then I've got a whole lot more work ahead of me as I'll have to set up extra ip's, add them to the firewall's network interface, create new listeners using that ip, etc... Can someone please confirm that I'm doing this correctly / incorrectly? Once I got my head wrapped around it all it seemed easy... then this. Thanks in advance.

  Read the article

• restrict access to IIS virtual directory from root website

  - by Senthil

  I have two domains (domain1.com and domain2.com). Both of them use the same Windows hosting server with IIS7. One of the domains is being called the "primary domain" by my hosting provider (GoDaddy) and it always points to the root folder that I was given. For the other domain, I have created a virtual directory in IIS and pointed it there. The folder structure is like this - root/ --Default.aspx --SomeFile.aspx --domain2folder/ ----Default.aspx ----Domain2SomeFile.aspx So, if I type domain1.com, I see the regulakr Default.aspx. But if I type domain2.com, I am shown the contents of domain2folder as if it were a separate web application - I think that is what IIS virtual directory is meant for. Well and good. But the problem is, when I type http://domain1.com/domain2folder, I see the domain2's website! But I don't want that to be shown when I use the path like that from domain1. Only if they use domain2.com, user should be able to see those contents. How can I do that? Hope I am making sense. Thanks.

  Read the article

• Laptop choice for development: MacBook Pro 17 vs Dell Studio XPS 16 vs HP Envy 15

  - by Shalan

  Hey! First things first - let me state that I am not intending to play games on this - I have narrowed down to these 3 purely based on specs and its individual brand reliability in the market. I intend to primarily use: Visual Studio 2008 Pro a lot (develop and deploy on Windows platforms) SQL Server 2005 Oracle 10g Adobe Photoshop CS4 Microsoft Expression Studio Google Sketchup I currently use a desktop PC (Core2Duo 2.66Ghz with 3GB DDRII memory) running Vista Business 32-bit - and I have to admit that, especially for Visual Studio, its quite sluggish to a point where it affects productivity. Furthermore, I intend to only use the notebook on a table - with a cooled surface, like granite :) - so I would appreciate people's input with regard to heat issues. Im aware that the Dell's primary exhaust gets blocked by the lid when open, but some reviews don't seem to place extraordinary emphasis on heat issues resulting from this. My options for the Dell/Alienware: Core i7 720QM 4GB DDRIII memory ATI mobility 3670 (512) 128GB Solid State Drive 16-inch Full HD RGB-LED LCD display (1080p) 3-year next-business-day support My configuration for the Apple MBP: Core2Duo 2.8Ghz (Im assuming the T9600) 4GB DDRIII memory 128GB Solid State Drive standard 1 year support The one advantage I think of with the MBP is that I can have the addition of OSX (though Im unsure what I would use it for, but purely to play around with a much-boasted-about OS) What are your thoughts on this, especially regarding build-quality, heat, performance and battery-life? Much thanks! ~shalan

  Read the article

• How do I fix issue causing "incomplete startup packet" log message trying to implement replication in Postgresql?

  - by colour me brad

  I've got two cloud servers running Ubuntu 13.04 and PostgreSQL 9.2. I've primarily used this blog post to aid me in setting things up. However, to do the initial database dump to the slave I'm using pg_start_backup/pg_stop_backup strategy used in this other blog post. I've read through the docs and postgres wikis as well. I ran into several problems I was able to solve, but I can't get past this wretched "the database is starting up" failure. I'm not sure if seeing "cp: cannot stat '/var/lib/postgresql/9.2/archive/00000001000000000000003A': No such file or directory" after "consistent recover state reached" is normal or the first sign of a problem. The searching I've done on "the database is starting up" and "incomplete startup packet" tells me that something is sending empty TCP packets to the slave. The only thing that even knows about the slave is the master, so I'm not sure why it's sending empty packets... Has anyone worked with this and have an idea what might be going wrong? The postgres log on the slave looks like so: 2013-08-26 13:01:38 CDT LOG: entering standby mode 2013-08-26 13:01:38 CDT LOG: restored log file "000000010000000000000039" from archive 2013-08-26 13:01:38 CDT LOG: incomplete startup packet 2013-08-26 13:01:39 CDT LOG: redo starts at 0/39000020 2013-08-26 13:01:39 CDT LOG: consistent recovery state reached at 0/390000E0 cp: cannot stat '/var/lib/postgresql/9.2/archive/00000001000000000000003A': No such file or directory 2013-08-26 13:01:39 CDT LOG: streaming replication successfully connected to primary 2013-08-26 13:01:39 CDT FATAL: the database system is starting up 2013-08-26 13:01:39 CDT FATAL: the database system is starting up 2013-08-26 13:01:40 CDT FATAL: the database system is starting up 2013-08-26 13:01:40 CDT FATAL: the database system is starting up 2013-08-26 13:01:41 CDT FATAL: the database system is starting up 2013-08-26 13:01:42 CDT FATAL: the database system is starting up 2013-08-26 13:01:42 CDT FATAL: the database system is starting up 2013-08-26 13:01:43 CDT FATAL: the database system is starting up 2013-08-26 13:01:43 CDT FATAL: the database system is starting up 2013-08-26 13:01:44 CDT FATAL: the database system is starting up 2013-08-26 13:01:44 CDT FATAL: the database system is starting up 2013-08-26 13:01:44 CDT LOG: incomplete startup packet 2013-08-26 13:03:27 CDT FATAL: the database system is starting up 2013-08-26 13:03:27 CDT FATAL: the database system is starting up 2013-08-26 13:03:30 CDT FATAL: the database system is starting up 2013-08-26 13:03:30 CDT FATAL: the database system is starting up thanks! brad

  Read the article

• When I log on to my company desktop, I log on to a domain. How is this domain name installed?

  - by learnerforever

  Hi, When I have to work on my machine in company, I have noticed that I log on to a domain (named on the basis of company name) and not really on that computer. From, what I understand, this has a few advantages, the primary being that I just need one password for the domain and can work through any of the machines in company. My questions are : What software on desktop/network have to be installed so that the desktop recognizes and gives me option of logging into a domain. I would guess that a software can be installed on desktop, and there we can configure the IP address of domain server of company and port number, which handles authentication. Is this correct? This takes me to another question that how are softwares installed on end machines in a company. Going to each machine physically and installing looks very unweildy from administrator point of view. An obvious solution would be to install softwares (and updates) over network. My question on this are: What protocols,keywords come into picture when administrator installs OS,softwares,updates from his administrator machine to end machine through network. Thanks,

  Read the article

• Configuration for a two machine ESXi cluster using VSA to present local storage to VMs

  - by MDMarra

  I'm designing a little vSphere 5 cluster for one of our remote sites. We have some IBM x3650s that have 6x 300GB 10K RPM drives in them, along with dual quad core CPUs and 24GB RAM. Because we use HP P4500 G2s at our primary site, we have licenses available for HP P4000 VSAs. I thought that this would be the perfect opportunity to use them. Below is a basic drawing of what I want to accomplish: I want to run a P4000 VSA on each server and run them in a Network RAID-10 (Lefthand speak for network mirroring, think of it as RAID 1 across nodes or as an active/active storage cluster). I will then present this storage to guests that will run on this mini-cluster. It will be managed by a vCenter Server on our main site. All connections will be GbE with two dedicated to storage. Management and Data will share a pair of connections, since I don't expect there to be high load. These servers are just there to provide directory services, dhcp, printing, etc. Does anyone see anything potentially wrong with this approach? Is this the best way to do this without adding additional dedicated storage heads? Are there any pitfalls in this design, besides the lack of dedicated Data/Mgmt interfaces?

  Read the article

• How Do I Enable My Ubuntu Server To Host Various SSL-Enabled Websites?

  - by Andy Ibanez

  Actually, I Have looked around for a few hours now, but I can't get this to work. The main problem I'm having is that only one out of two sites works. I have my website which will mostly be used for an app. It's called atajosapp.com . atajosapp.com will have three main sites: www.atajosapp.com <- Homepage for the app. auth.atajosapp.com <- Login endpoint for my API (needs SSL) api.atajosapp.com <- Main endpoint for my API (needs SSL). If you attempt to access api.atajosapp.com it works. It will throw you a 403 error and a JSON output, but that's fully intentional. If you try to access auth.atajosapp.com however, the site simply doesn't load. Chrome complains with: The webpage at https://auth.atajosapp.com/ might be temporarily down or it may have moved permanently to a new web address. Error code: ERR_TUNNEL_CONNECTION_FAILED But the website IS there. If you try to access www.atajosapp.com or any other HTTP site, it connects fine. It just doesn't like dealing with more than one HTTPS websites, it seems. The VirtualHost for api.atajosapp.com looks like this: <VirtualHost *:443> DocumentRoot /var/www/api.atajosapp.com ServerName api.atajosapp.com SSLEngine on SSLCertificateFile /certificates/STAR_atajosapp_com.crt SSLCertificateKeyFile /certificates/star_atajosapp_com.key SSLCertificateChainFile /certificates/PositiveSSLCA2.crt </VirtualHost> auth.atajosapp.com Looks very similar: <VirtualHost *:443> DocumentRoot /var/www/auth.atajosapp.com ServerName auth.atajosapp.com SSLEngine on SSLCertificateFile /certificates/STAR_atajosapp_com.crt SSLCertificateKeyFile /certificates/star_atajosapp_com.key SSLCertificateChainFile /certificates/PositiveSSLCA2.crt </VirtualHost> Now I have found many websites that talk about possible solutions. At first, I was getting a message like this: _default_ VirtualHost overlap on port 443, the first has precedence But after googling for hours, I managed to solve it by editing both apache2.conf and ports.conf. This is the last thing I added to ports.conf: <IfModule mod_ssl.c> NameVirtualHost *:443 # SSL name based virtual hosts are not yet supported, therefore no # NameVirtualHost statement here NameVirtualHost *:443 Listen 443 </IfModule> Still, right now only api.atajosapp.com and www.atajosapp.com are working. I still can't access auth.atajosapp.com. When I check the error log, I see this: Init: Name-based SSL virtual hosts only work for clients with TLS server name indication support (RFC 4366) I don't know what else to do to make both sites work fine on this. I purchased a Wildcard SSL certificate from Comodo that supposedly secures *.atajosapp.com, so after hours trying and googling, I don't know what's wrong anymore. Any help will be really appreciated. EDIT: I just ran the apachectl -t -D DUMP_VHOSTS command and this is the output. Can't make much sense of it...: root@atajosapp:/# apachectl -t -D DUMP_VHOSTS apache2: Could not reliably determine the server's fully qualified domain name, using atajosapp.com for ServerName [Thu Nov 07 02:01:24 2013] [warn] NameVirtualHost *:443 has no VirtualHosts VirtualHost configuration: wildcard NameVirtualHosts and _default_ servers: *:443 is a NameVirtualHost default server api.atajosapp.com (/etc/apache2/sites-enabled/api.atajosapp.com:1) port 443 namevhost api.atajosapp.com (/etc/apache2/sites-enabled/api.atajosapp.com:1) port 443 namevhost auth.atajosapp.com (/etc/apache2/sites-enabled/auth.atajosapp.com:1) *:80 is a NameVirtualHost default server atajosapp.com (/etc/apache2/sites-enabled/000-default:1) port 80 namevhost atajosapp.com (/etc/apache2/sites-enabled/000-default:1)

  Read the article

• Unable to access Windows share

  - by mbnoimi

  I've installed Alfresco 4.2.d under Ubuntu 12.04 LTS; Everything done fine except I can't access it from Windows share although I got the link from Alfresco explorer which is: file:///%5C%5CECSA%5CAlfresco%5CSites%5Cswsdp%5CdocumentLibrary%5CAgency%20Files%5CImages%5Ccoins.JPG I tried to access it from: \\ECSA but I failed too so I made a ping (192.168.0.70 is server IP) then I got: C:\Users\user>ping 192.168.0.70 Pinging 192.168.0.70 with 32 bytes of data: Reply from 192.168.0.70: bytes=32 time<1ms TTL=64 Reply from 192.168.0.70: bytes=32 time<1ms TTL=64 Reply from 192.168.0.70: bytes=32 time<1ms TTL=64 Reply from 192.168.0.70: bytes=32 time<1ms TTL=64 Ping statistics for 192.168.0.70: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms C:\Users\user>ping ECSA Ping request could not find host ECSA. Please check the name and try C:\Users\user> Some logs of what's going on: C:\Users\user>net view ECSA System error 1707 has occurred. The network address is invalid. C:\Users\user>nbtstat -a 192.168.0.70 Local Area Connection: Node IpAddress: [192.168.0.84] Scope Id: [] NetBIOS Remote Machine Name Table Name Type Status --------------------------------------------- ECSA <20> UNIQUE Registered ECSA <00> UNIQUE Registered WORKGROUP <00> GROUP Registered MAC Address = 00-00-00-00-00-00 C:\Users\user> CIFS Server Configuration in file-servers.properties ### CIFS Server Configuration - file-servers.properties ### cifs.enabled=true cifs.serverName=${localname}A cifs.domain= cifs.broadcast=255.255.255.255 cifs.bindto=192.168.0.70 cifs.ipv6.enabled=false cifs.hostannounce=true cifs.disableNIO=false cifs.disableNativeCode=false cifs.sessionTimeout=900 cifs.maximumVirtualCircuitsPerSession=16 cifs.tcpipSMB.port=445 cifs.netBIOSSMB.sessionPort=139 cifs.netBIOSSMB.namePort=137 cifs.netBIOSSMB.datagramPort=138 cifs.WINS.autoDetectEnabled=true cifs.WINS.primary=192.168.0.70 cifs.WINS.secondary=192.168.0.1 cifs.sessionDebug= cifs.pseudoFiles.enabled=true cifs.pseudoFiles.explorerURL.enabled=true cifs.pseudoFiles.explorerURL.fileName=__Alfresco.url cifs.pseudoFiles.shareURL.enabled=false cifs.pseudoFiles.shareURL.fileName=__Share.url How can I fix this issue?

  Read the article

• Integrating HP Systems Insight Manager into an existing environment

  - by ewwhite

  I'm working with an environment that spans multiple data centers/sites and consists primarily of HP ProLiant servers (G5-G7) running Linux. The mix is 30% RHEL/CentOS, the rest are Gentoo :(. I also have a few dozen virtual machines running back-office and Windows servers on VMWare ESX hosts. I run OpenNMS to pull SNMP data from the various server nodes and networking devices. While OpenNMS works wonderfully for up/down, thresholds and notifications, it's native handling of traps is a little rough and the graphs are not particularly pretty. I use Orca/RRD graphs for performance trending and nice graphs. I'm tasked with inventorying the environment and wanted to come up with a clean way to organize server information. Since my environment is mostly HP, I've been playing with HP Systems Insight Manager as a way to extract server data and to deploy HP health/monitoring packages and firmware. The Gentoo systems eventually have to be converted to CentOS, so getting a quick assessment of what hardware is where would be great. Although I've read through a few hundred pages of HP manuals, I'm having a difficult time understanding how to get HP SIM to do what I want, though. My main problems are: I have about 40 subnets to deal with; 98% connected with private lines to facilities across the globe. I don't want to initiate an HP SIM discovery only to pull back every piece of intermediate networking hardware and equipment from all of the locations. I'd like this to focus on the servers. I have OpenNMS configured to accept traps. I don't want HP SIM to duplicate that effort. It seems like the built-in software deployment tool wants to overwrite the trapsink parameters for the systems it encounters during discovery. I have about 10 administrative username/password combinations in use across this infrastructure. Is there a more efficient way to get HP SIM to do the discovery or break discovery into manageable chunks? In terms of general workflow, do people typically install the HP Management Agents during the initial OS deployment (e.g. kickstart post script) or afterwards from HP SIM? Is HP SIM too thick/fat to be an inventory tool? I can't tell if it's meant to be used standalone or alongside other monitoring products. Since the majority of the systems I'm trying to track are those running Gentoo (in order to plan the move to CentOS), is there any way for HP SIM to extract system model information from them ( like dmidecode)? I have systems here where I may have an SSH key established, but not direct user or login access. Is there a way for me to import an SSH private/public key pair into HP SIM to reach out to the servers that can't accept standard credentials? There are a handful of sites where I have inconsistent access or have a double-NAT situation. I may be able to poke a server, but it may not be able to find its way back to the management system. Is there a workaround for this? The certificate configuration for HP SIM seems complicated. What is the preferred setup for trust between systems? I'd also appreciate any notes or recommendations to using this product. Or if there's a better way to do this, I'd like to know.

  Read the article

• award phoenix bios not recognizing my sata hdd.

  - by josh

  What am I doing wrong? I have a custom built comp with a Fatal1ty AA8XE mobo. It has 4 SATA ports and one IDE port. When i first got it, I had a really hard time putting in more than one hard drive. Right now i have one 120gb IDE HDD on master and my DVD+-RW on slave connected to the one IDE spot on the mobo. I ripped a bunch of movies and filled up my HDD, so I got a WD 80gb SATA drive. I plugged it into SATA1 and hooked up the power, turned on comp, went into bios. The only thing in any option in any of the menues in this crazy lookin bios is a thing that says "SATA mode". i put it on IDE, set it so PATA is primary, SATA is secondary. booted up my comp, nothin. Not recognizing the SATA. I went back into the bios and checked it all again. I saw that it says SATA2 and SATA4 are the secondaries so i put it on SATA2, booted, nothing, same with SATA4, same with SATA3, all same as SATA1. Bios and wt os are not recognizing the drive as being there at all. I even downloaded and printed the almost 100 page manual for the mobo, read the entire thing, and still can't figure it out. I know there are a lot of people out there smarter than me when it comes to computers. So please, somebody, anybody, please tell me something that I'm not seeing. Some setting somewhere that I didn't configure right. There is something, obviously, but I can't find it. As far as i can tell, everything is set perfectly fine for my 120gb to be the master and the SATA to be the slave. I don't know what I'm doing wrong but I'm seriously about to throw this computer out the window. thankyou in advance to whoever attempts to help.

  Read the article

• MySQL table does not exist

  - by Phanindra

  I am getting following error in err file. 110803 6:51:26 InnoDB: Error: table `ims`.`temp_discoveryjobdetails` already exists in InnoDB internal InnoDB: data dictionary. Have you deleted the .frm file InnoDB: and not used DROP TABLE? Have you used DROP DATABASE InnoDB: for InnoDB tables in MySQL version <= 3.23.43? InnoDB: See the Restrictions section of the InnoDB manual. InnoDB: You can drop the orphaned table inside InnoDB by InnoDB: creating an InnoDB table with the same name in another InnoDB: database and copying the .frm file to the current database. InnoDB: Then MySQL thinks the table exists, and DROP TABLE will InnoDB: succeed. InnoDB: You can look for further help from InnoDB: http://dev.mysql.com/doc/refman/5.1/en/innodb-troubleshooting.html And when I do the same, like copying the frm file from other database to here and drop the table, i am getting following error, InnoDB: Error: trying to load index PRIMARY for table ims/temp_discoveryjobdetails InnoDB: but the index tree has been freed! 110803 6:50:26 InnoDB: Error: table `ims`.`temp_discoveryjobdetails` does not exist in the InnoDB internal InnoDB: data dictionary though MySQL is trying to drop it. InnoDB: Have you copied the .frm file of the table to the InnoDB: MySQL database directory from another database? InnoDB: You can look for further help from InnoDB: http://dev.mysql.com/doc/refman/5.1/en/innodb-troubleshooting.html Please any one help me out of this. Also can any one tell me why this error is coming. EDIT: The issue is occurring only when disk size is full and when we use Truncate table. Also this is occurring only in 5.1 version but not in 5.0 version.

  Read the article

• How do I easily repair a single unreadable block on a Linux disk?

  - by Nelson

  My Linux system has started throwing SMART errors in the syslog. I tracked it down and believe the problem is a single block on the disk. How do I go about easily getting the disk to reallocate that one block? I'd like to know what file got destroyed in the process. (I'm aware that if one block fails on a disk others are likely to follow; I have a good ongoing backup and just want to try to keep this disk working.) Searching the web leads to the Bad block HOWTO, which describes a manual process on an unmounted disk. It seems complicated and error-prone. Is there a tool to automate this process in Linux? My only other option is the manufacturer's diagnostic tool, but I presume that'll clobber the bad block without any reporting on what got destroyed. Worst case, it might be filesystem metadata. The disk in question is the primary system partition. Using ext3fs and LVM. Here's the error log from syslog and the relevant bit from smartctl. smartd[5226]: Device: /dev/hda, 1 Currently unreadable (pending) sectors Error 1 occurred at disk power-on lifetime: 17449 hours (727 days + 1 hours) ... Error: UNC at LBA = 0x00d39eee = 13868782 There's a full smartctl dump on pastebin.

  Read the article

• Enabling Hyper-V Integrated Services Time Sync Services versus Internet Time Synchronization

  - by cpuguru

  Should I deselect the "Synchronize with an Internet Time Server" checkbox under the VM's "Date and Time - Internet Time Settings" tab if the "Time Synchronization Service" for a Hyper-V-based Virtual Machine is enabled? One of the Integration Services that Hyper-V provides is the Time Synchronization Service, which can be enabled/disabled by going to a VM's Settings-Integration Services setting in the Management section. I believe this is checked by default. When you install a Windows Server 2008 OS in a VM on the Hyper-V server, it comes with the "Synchronize with an Internet Time Server" option set, pointing to "time.windows.com". I'd think that if the parent Hyper-V server is set to one time server, and the child VM is pointing to a different time server, there would be a momentary blip if the two are not spot on with their times when the synchronization services run. So the question is, which time sync service should I use? I'm assuming not both. And what is the advantage of one over the other? Note: This question assumes that the machines are not joined to a domain. If they were, the machines would also try to update their time against the domain controller with the primary domain controller role too, right? Thanks!

  Read the article

• Put one monitor of a dual monitor windows system into standby

  - by Psycogeek

  Standby not Disabled! When running 2 monitors on windows 7 or Windows XP, I would like to be able to put one of the monitors at a time into standby. The method can be manual. When running 2 monitors , the second monitor is not always needed, shutting off the monitors own power switch will turn off the monitor, that does work Ok. Problems with that are , the delay with the monitor logo at turn on, and the power switch is not very accessable, and the switch might not live forever turning it on and off so many times. Using disable methods like devcon, WIN-P and Display, causes all the windows to properly move to the other monitor. While that is what a person would want to happen so they can get hold of the windows, that is not what I want to happen, and some things on the other monitor have to be re-arranged after a re-enable. By putting it into standby mode, nothing changes other than the monitor going into standby. Disconnecting the DVI cable still can cause the system to (properly) shift all the windows over to the one monitor, just like any of the disable methods do. That makes a mess of the windows, and is so unacceptable, that I would prefer to leave the monitor on, wasting power and the hardware, when it could easily go into standby for some time. For both monitors I am using a "MonitorOff" program that puts both monitors into standby, but I can not find a utility that will put only ONE monitor into standby for the windows system. If someone comes along and suggests "ultramon" you must know for a fact that it will put One of either of the monitors into actual standby. And it does not really suit me to use ultramon, I tested it (it was nice) and I did not feel that it was a program I wanted. The 2 monitors are running off of an ATI 4890 card, they are both hooked up DVI-I, the OS is both Windows 7 (primary) and Windows XP. In addition it would also be interesting to have seperate standby activity timers, and follow mouse kind of standby changes, but any manuel method , shortcut, batch , tray, or gadget kind of operation would be a good start.

  Read the article

• Trying to configure DNS on a Godaddy Virtual Dedicated host, Mediatemple Domain Registration [closed]

  - by dclowd9901

  A client of mine purchased VD hosting with Godaddy and a domain name with Mediatemple. I've never configured DNS from scratch, and I'm finding it very difficult to find any sort of explanation on how to go about it. As of right now, Mediatemple is pointing to the Godaddy's ns1.domaincontrol.com and ns2.domaincontrol.com nameservers. The VD hosting on Godaddy (via their Simple Control Panel) has options to "Add a new domain", which brings you through a wizard of sorts that asks you if the domain has already been registered (yes), what it is (dclowd9901.com for this example), create a system username and password for it (with checkboxes for SSH and FTP access), which level of user can administer it, and whether a mail account should be setup. When complete, it also creates a zone file. In this zone file, the Primary nameserver is ns1.dclowd9901.com; the records are as follow (where 12.23.12.34 is the presumed host): @ A 12.23.12.34 @ NS ns1 @ NS ns2 ns1 A 12.23.12.34 ns2 A 12.23.12.34 @ MX mail www A 12.23.12.34 ftp A 12.23.12.34 ssh A 12.23.12.34 mail A 12.23.12.34 If anyone can shed any light on this for me, explain to me the interactions between the registrar and the host and so on, I'd be very grateful. Thanks in advance for the help.

  Read the article

• Nexus 1000v VEM fails on 2 out of 8 hosts.

  - by cougar694u

  I have 8 ESXi hosts. I do a fresh install from the installable CD directly to 4u1. We have another 2-node cluster with a working Nexus 1000v primary & secondary. Everything's up and running. I installed 6 hosts and everything worked great, migrated them to the Nexus DVS, and VUM installed the modules. I did the 7th host, and when I tried to migrate it to the DVS, it failed with the following error: Cannot complete a Distributed Virtual Switch operation for one or more host memebers. DVS Operation failed on host , error durring the configuration of the host: create dvswitch failed with the following error message: SysinfoException: Node (VSI_NODE_net_create) ; Status(bad0003)= Not found ; Message = Instance(0): Inpute(3) DvsPortset-0 256 cisco_nexus_1000v got (vim.fault.PlatformConfigFault) exception Then, I tried to do host 8, and got the exact same problem. It worked about 15 minutes prior when I did host 6, nothing changed, then went to host 7 and it failed. If I try to remediate either of these two hosts, either patches or extensions, it fails. Anyone else have these problems?

  Read the article

• external drive enclosure -> software RAID 5?

  - by memilanuk

  Hello all, I have two older PCs on my LAN posing as 'servers'... one running FreeNAS off a USB stick using three 500GB hdds in a ZFS RAID-Z pool serving as storage for the LAN and one running Debian Lenny with an 80GB drive used as a general purpose 'tinker' box that I can ssh into, etc. Problem is that the SMART report for one of those 500GB drives in the FreeNAS box is showing some pre-failure attributes, and the whole array is a little small anyways. Rather than simply replace one 500GB drive with another 500GB drive, and have no backup of the file server, I'd like to upgrade all the drives to 2TB ones - but I have no where to store that much data in the mean while. As such, I started looking at getting a 4-bay external drive enclosure with an eSATA card for the Debian box, with the hopes of creating a RAID5 + LVM setup using those drives and backing the data up to that external drive enclosure. After the backup is done, replace the drives in the FreeNAS box and rebuild the array there and mirror the data back. Then, I'd have both the primary storage (on the FreeNAS box) and a backup (which I don't have currently) using the external drive enclosure on the Debian box. My big question is... most of these external drive boxes seem to claim support for JBOD, RAID 0, 1, 10, 5, etc. - should I presume that is simply fake RAID like many commodity mobos have, and not really usable in Linux? In that case, with all the drives hanging off the one eSATA connection, will Linux (specifically Debian Squeeze, as I plan on upgrading that box here shortly) see all four drives, or just the first one? Will I be able to configure them in a RAID5 array as desired? Thanks, Monte

  Read the article

< Previous Page | 533 534 535 536 537 538 539 540 541 542 543 544  | Next Page >