Search Results

Search found 1774 results on 71 pages for 'parallel for'.

Page 54/71 | < Previous Page | 50 51 52 53 54 55 56 57 58 59 60 61  | Next Page >

• Multiple IPs on firewall, are these virtual interfaces or what?

  - by Jakobud

  We have 5 static IP addresses from our ISP: XXX.XXX.XXX.180 XXX.XXX.XXX.181 XXX.XXX.XXX.182 XXX.XXX.XXX.183 XXX.XXX.XXX.184 On our firewall box, the NIC that is connected to our cable modem, appears to have all 5 IP addresses set on it. A previous IT guy set this thing up, and I'm not sure exactly what he did. Are these virtual interfaces on this NIC or what? Here is my ip addr output for that NIC: rwd0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether XX:XX:XX:XX:XX:XX brd ff:ff:ff:ff:ff:ff inet XXX.XXX.XXX.180/24 brd XXX.XXX.XXX.186 scope global rwd0 inet XXX.XXX.XXX.181/29 brd XXX.XXX.XXX.186 scope global rwd0:FWB9 inet XXX.XXX.XXX.182/29 brd XXX.XXX.XXX.186 scope global secondary rwd0:FWB10 inet XXX.XXX.XXX.183/29 brd XXX.XXX.XXX.186 scope global secondary rwd0:FWB11 inet XXX.XXX.XXX.184/29 brd XXX.XXX.XXX.186 scope global secondary rwd0:FWB12 inet6 fe80::250:8bff:fe61:5734/64 scope link valid_lft forever preferred_lft forever I'm a bit new to firewalls and networking so I'm just trying to figure out what he had going on here. I know he used Firewall Builder to configure the iptables rules, maybe that has something to do with the "FWB" I see in those names? So my questions are: What is going on here? Virtual Interfaces? Or something else? If we want to put in a second firewall in parallel with this firewall but we only want it to handle traffic to XXX.XXX.XXX.182, how do we get rid of the static XXX.XXX.XXX.182 address on this existing firewall box?

  Read the article

• 32 core (each physical core) 2.2 GhZ or 12 core (6 physical cores) 3.0GHZ?

  - by Tejaswi Rana

  I am working on a multithreaded application (Forex trading app built on C#) and had the client upgrade from the 12 core 3.0GHZ machine (Intel) to a 32 core 2.2 Ghz machine (AMD). The PassMark benchmark results were significantly higher when using multicores doing Integer, Floating and other calculations while for a single core calculation it was a bit slower than the pack (others that were being compared to with similar config as the 12 core one). Oh it also comes with 64 GB RAM (4 times as the other one) and a much faster SSD. So after configuring and running the application on that machine, not only did it not perform as well, it was significantly slower. We're talking about 30seconds - 1 minute slower on an app that usually completes processing within 5-20 secs. The application uses MAX DEGREE of PARALLELISM (TPL) which I've tried setting to number of cores and also half of that. I've also tried running single threaded and without setting any limits in parallel threading. While it may be the hardware has some issues, I am wondering if the CPU processing speed is the issue. I can overclock to 3.0 GHZ. But is that even a good idea? Server Info - AMD http://www.passmark.com/forum/showthread.php?4013-AMD-Dual-6272-performance-is-60-lower-than-benchmarks Seems that benchmark was wrong to start with - officially. Intel i7 3930k OS (same in both) Windows 7 Professional 64-bit

  Read the article

• How do I run a stable Windows XP kvm guest on Ubuntu 10.04?

  - by Jean-Paul Calderone

  I have three Windows XP guests running on a recently upgraded 64-bit Ubuntu 10.04 system. Occasionally (on the order of once every few days), one of the guests will become non-responsive and the kvm process on the host which is running that guest will start consuming 100% CPU. It will continue to do so until it is killed. When restarted, it will be fine for a while, and then the issue repeats. The kvm command line used to run all three guests is this: /usr/bin/kvm -S -M pc-0.12 -enable-kvm -m 1024 -smp 1 -name bigdog21vmxp1 \ -uuid ea47ff84-125b-16f7-9a4d-a6d0d8bab46a \ -chardev socket,id=monitor,path=/var/lib/libvirt/qemu/bigdog21vmxp1.monitor,server,nowait \ -monitor chardev:monitor \ -localtime \ -boot c \ -drive file=/var/lib/libvirt/images/windowsxp-1.qcow2,if=ide,index=0,boot=on,format=qcow2 \ -net nic,macaddr=54:52:00:02:06:0e,vlan=0,name=nic.0 \ -net tap,fd=58,vlan=0,name=tap.0 \ -chardev pty,id=serial0 \ -serial chardev:serial0 \ -parallel none \ -usb \ -usbdevice tablet \ -vnc 127.0.0.1:1 \ -k en-us \ -vga cirrus \ -soundhw es1370 Why do the systems misbehave this way sometimes? And what configuration can I change in order to fix it? Or, if the problem is due to a bug in kvm, what is the process for isolating a kvm failure so that the developers have a chance of fixing it?

  Read the article

• Apache /server-status/ gives a 404 not found

  - by kapshure

  I am trying to solve a problem where Apache stats aren't displaying correctly in Munin. I've ran through quite a bit of checks and tests regarding Munin setup, but I think my issue is related to Apache, but my skill set there is lacking. first, system info: monitored server CentOS 5.3 kernel 2.6.18-128.1.1.el5 Apache/2.2.3 "server-status" directive in httpd.conf (i've cross-compared this with another system that i did a successful parallel install of Munin on, correctly showing Apache stats, and the directive below is the same for both) ExtendedStatus On <Location /server-status> SetHandler server-status Order deny,allow Deny from all Allow from 127.0.0.1 </Location> ran lynx http://localhost/server-status got HTTP/1.1 404 taking a look at Apache access_log: 127.0.0.1 - - [13/Oct/2010:07:00:47 -0700] "GET /server-status HTTP/1.0" 404 11237 "-" "Lynx/2.8.5rel.1 libwww-FM/2.14 SSL-MM/1.4.1 OpenSSL/0.9.8e-fips-rhel5" mod_status is also loaded: % grep "mod_status" /etc/httpd/conf/httpd.conf LoadModule status_module modules/mod_status.so iptables is turned off also i did notice that the ownership status on httpd.conf on this system is root.root.. whereas the system that is displaying correctly is apache.www -- not certain that this matters?? its got to be permission issue, but i'm not certain where the permissions are messed up. any thoughts on why the test of server-status is giving me a 404?

  Read the article

• MySQL problem with many concurrent connections

  - by user48303

  Hi, here's a sixcore with 32 GB RAM. I've installed MySQL 5.1.47 (backport). Config is nearly standard, except max_connections, which is set to 2000. On the other hand there is PHP5.3/FastCGI on nginx. There is a very simple php application which should be served. NGINX can handle thousands of request parallel on this machine. This application accesses MySQL via mysqli. When using non-persistent connections in mysqli there is a problem when reaching 100 concurrent connections. [error] 14074#0: *296 FastCGI sent in stderr: "PHP Warning: mysqli::mysqli(): [2002] Resource temporarily unavailable (trying to connect via unix:///tmp/mysqld.sock) in /var/www/libs/db.php on line 7 I've no idea to solve this. Connecting via tcp to mysql is terrible slow. The interesting thing is, when using persistent connections (add 'p:' to hostname in mysqli) the first 5000-10000 thousand requests fail with the same error as above until max connections (from webserver, set to 1500) is reached. After the first requests MySQL keeps it 1500 open connections and all is fine, so that I can make my 1500 concurrent requests. Huh? Is it possible, that this is a problem with PHP FastCGI?

  Read the article

• Error while installing boost_1_54

  - by Farhat

  On trying to install boost I get this error during configuration checks. Googling did not give any pointers. [root@heracles boost_1_54_0]# ./b2 install Performing configuration checks - 32-bit : no (cached) - 64-bit : yes (cached) - arm : no (cached) - mips1 : no (cached) - power : no (cached) - sparc : no (cached) - x86 : yes (cached) error: No best alternative for libs/coroutine/build/allocator_sources next alternative: required properties: <link>static <target-os>windows <threading>multi not matched next alternative: required properties: <link>static <segmented-stacks>on <threading>multi not matched next alternative: required properties: <link>static <threading>multi not matched - has_icu builds : no (cached) warning: Graph library does not contain MPI-based parallel components. note: to enable them, add "using mpi ;" to your user-config.jam - zlib : yes (cached) - iconv (libc) : yes (cached) - icu : no (cached) - icu (lib64) : no (cached) - compiler-supports-ssse3 : yes (cached) - compiler-supports-avx2 : no (cached) - gcc visibility : yes (cached) - long double support : yes (cached) warning: skipping optional Message Passing Interface (MPI) library. note: to enable MPI support, add "using mpi ;" to user-config.jam. note: to suppress this message, pass "--without-mpi" to bjam. note: otherwise, you can safely ignore this message. error: No best alternative for libs/coroutine/build/allocator_sources next alternative: required properties: <link>static <target-os>windows <threading>multi not matched next alternative: required properties: <link>static <segmented-stacks>on <threading>multi not matched next alternative: required properties: <link>static <threading>multi not matched - zlib : yes (cached) How can the alternative for allocator sources be located? Thanks.

  Read the article

• Can MS Services for Unix be deployed and accessed from a shared drive?

  - by Ian C.

  I'm interested in experimenting with replacing our dependency on MKS with MS' Sevices for Unix toolset. I was wondering if anyone has any experience with deploying SFU on a shared drive? We like to, wherever possible, host our dev tools on one central NAS and call to the NAS to access the tools instead of rolling stuff out to each and every desktop. I'm not interested in the NFS support or ActiveState Perl. Really, none of the daemon technology is required here. I'm looking for replacements for the coreutils/binutils stuff you find in Linux (and MKS on Windows): sed, awk, csh, bash, grep, ls, find -- the meat-and-potates command line apps that our build and test scripts are built around. If I limit the install to just the Interix GNU Components (and maybe the Remote Connectivity components) will is run nicely from a shared location? To head off some questions: Yes, I've looked at Cygwin. Unfortunately it's performance in our build and test environment is poor. It runs considerably slower than MKS and it's not a direct drop-in replacement for MKS (thanks to its internal pathing and limitations with commands like 'ps'), so it's a tougher sell. Yes, I'm looking at the MinGW offering in parallel to this.

  Read the article

• Splitting build cross the network?

  - by Dandikas

  Is there a known solution for splitting build process cross the network machines? Use case: We are an average software development company. We own around 50 development workstations (Quad Core 2.66Ghz, 4 GB ram, 200 GB raid). No need to tell that at any single moment not every machine is loaded to the max. There are 5 to 15 projects running simultaneously at any single moment. Obviously all of them are continuously build on server, than deployed to proper environment. Single project build is taking from 3 to 15 minutes. The problem: Whenever we build 5 projects in a row the last project is going to be ready after around 25 - 50 minutes. Building in parallel does not solve the problem (build is only a part of the game, than you need to deploy, run tests etc.) YES the correct solution is to add another build server, but "That involves buying new Expensive hardware, and we already spent a lot!". Yea, right(damn them)! Anyway. What about splitting build among developers workstation? Lets say whenever we need to build project "A" we check 5 workstations and start build on all that are not overloaded. The build can be canceled by a developer if he really needs all the power of his machine as long as there is at least 1 machine that is still building. After build is finished deployment can be performed to a proper environment (hosted on some server, not on workstation :) ). The bigger the company the more this makes sense to me. Anyone tried something like this? Are there any good practices? Any helpful software?

  Read the article

• Remote Socket Read In Multi-Threaded Application Returns Zero Bytes or EINTR (104)

  - by user39891

  Hi. Am a c-coder for a while now - neither a newbie nor an expert. Now, I have a certain daemoned application in C on a PPC Linux. I use PHP's socket_connect as a client to connect to this service locally. The server uses epoll for multiplexing connections via a Unix socket. A user submitted string is parsed for certain characters/words using strstr() and if found, spawns 4 joinable threads to different websites simultaneously. I use socket, connect, write and read, to interact with the said webservers via TCP on their port 80 in each thread. All connections and writes seems successful. Reads to the webserver sockets fail however, with either (A) all 3 threads seem to hang, and only one thread returns -1 and errno is set to 104. The responding thread takes like 10 minutes - an eternity long:-(. *I read somewhere that the 104 (is EINTR?), which in the network context suggests that ...'the connection was reset by peer'; or (B) 0 bytes from 3 threads, and only 1 of the 4 threads actually returns some data. Isn't the socket read/write thread-safe? I use thread-safe (and reentrant) libc functions such as strtok_r, gethostbyname_r, etc. *I doubt that the said webhosts are actually resetting the connection, because when I run a single-threaded standalone (everything else equal) all things works perfectly right, but of course in series not parallel. There's a second problem too (oops), I can't write back to the client who connect to my epoll-ed Unix socket. My daemon application will hang and hog CPU 100% for ever. Yet nothing is written to the clients end. Am sure the client (a very typical PHP socket application) hasn't closed the connection whenever this is happening - no error(s) detected either. Any ideas? I cannot figure-out whatever is wrong even with Valgrind, GDB or much logging. Kindly help where you can.

  Read the article

• rc scripts dependencies

  - by chris

  On a Ubuntu 10.04.1 LTS server install certain services fail to start properly after a reboot. I have a couple of virtual interfaces defined on eth0: /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 172.16.5.240 netmask 255.255.255.0 gateway 172.16.5.1 auto eth0:1 iface eth0:1 inet static address 172.16.5.241 netmask 255.255.255.0 gateway 172.16.5.1 auto eth0:2 iface eth0:2 inet static address 172.16.5.242 netmask 255.255.255.0 gateway 172.16.5.1 auto eth0:3 iface eth0:3 inet static address 172.16.5.243 netmask 255.255.255.0 gateway 172.16.5.1 and so on... The services that try to bind to for example 172.16.5.243 fail during boot, complaining that there is no such IP address. My questions: 1) Are the services started parallel by default? Can I disable that so they run sequentially? 2) Is there a way to define dependencies between rc scripts? I'm only familiar with the defining the order of seqentially started scripts using the numbers in /etc/rc[0-6].d/) Any other fix or workaround appreciated.

  Read the article

• Traffic shaping on Linux with HTB: weird results

  - by DADGAD

  I'm trying to have some simple bandwidth throttling set up on a Linux server and I'm running into what seems to be very weird stuff despite a seemingly trivial config. I want to shape traffic coming to a specific client IP (10.41.240.240) to a hard maximum of 75Kbit/s. Here's how I set up the shaping: # tc qdisc add dev eth1 root handle 1: htb default 1 r2q 1 # tc class add dev eth1 parent 1: classid 1:1 htb rate 75Kbit # tc class add dev eth1 parent 1:1 classid 1:10 htb rate 75kbit # tc filter add dev eth1 parent 1:0 protocol ip prio 1 u32 match ip dst 10.41.240.240 flowid 1:10 To test, I start a file download over HTTP from the said client machine and measure the resulting speed by looking at Kb/s in Firefox. Now, the behaviour is rather puzzling: the DL starts at about 10Kbyte/s and proceeds to pick up speed until it stabilizes at about 75Kbytes/s (Kilobytes, not Kilobits as configured!). Then, If I start several parallel downloads of that very same file, each download stabilizes at about 45Kbytes/s; the combined speed of those downloads thus greatly exceeds the configured maximum. Here's what I get when probing tc for debug info [root@kup-gw-02 /]# tc -s qdisc show dev eth1 qdisc htb 1: r2q 1 default 1 direct_packets_stat 1 Sent 17475717 bytes 1334 pkt (dropped 0, overlimits 2782 requeues 0) rate 0bit 0pps backlog 0b 12p requeues 0 [root@kup-gw-02 /]# tc -s class show dev eth1 class htb 1:1 root rate 75000bit ceil 75000bit burst 1608b cburst 1608b Sent 14369397 bytes 1124 pkt (dropped 0, overlimits 0 requeues 0) rate 577896bit 5pps backlog 0b 0p requeues 0 lended: 1 borrowed: 0 giants: 1938 tokens: -205561 ctokens: -205561 class htb 1:10 parent 1:1 prio 0 **rate 75000bit ceil 75000bit** burst 1608b cburst 1608b Sent 14529077 bytes 1134 pkt (dropped 0, overlimits 0 requeues 0) **rate 589888bit** 5pps backlog 0b 11p requeues 0 lended: 1123 borrowed: 0 giants: 1938 tokens: -205561 ctokens: -205561 What I can't for the life of me understand is this: how come I get a "rate 589888bit 5pps" with a config of "rate 75000bit ceil 75000bit"? Why does the effective rate get so much higher than the configured rate? What am I doing wrong? Why is it behaving the way it is? Please help, I'm stumped. Thanks guys.

  Read the article

• Firefox proxy authentication with Kerberos: one service ticket per connection (Linux)

  - by Dari

  I am trying to enable proxy authentication via Kerberos for Firefox. The setup is: Active Directory domain (for LDAP and Kerberos; this works and I can log in the computer and get Kerberos tickets without problems) Microsoft Windows witness machine (on which Firefox runs fine with no ticket problem) CentOS 6.3 system with Firefox (the tests were performed with both the 10.0.1 ESR found in the CentOS package repositories and the 15.0.1 downloaded from Mozilla's website) BlueCoat proxy with Kerberos authentication enabled For the moment, Firefox requests an element of a website, gets an HTTP error code of "407 Proxy Authentication Required" from the proxy, gets a ticket granting service (TGS) from the domain for the proxy and performs the request again while passing the ticket. The transaction runs fine. However, when more elements are requested (in parallel), Firefox requests one more ticket per proxy connection. And this takes many DNS queries, Kerberos interactions with domain controllers and costs a lot of time (for example, the home page of Adobe takes several minutes to load and at the end, I have about 30 valid Kerberos tickets). I am stuck on this since a while, and help would be greatly appreciated. Minor information: the CentOS operating system is virtualized with VMware Player 3.1.3, but I do not think this would be a game changer.

  Read the article

• mkfs Operation Takes Very Long on Linux Software Raid 5

  - by Elmar Weber

  I've set-up a Linux software raid level 5 consisting of 4 * 2 TB disks. The disk array was created with a 64k stripe size and no other configuration parameters. After the initial rebuild I tried to create a filesystem and this step takes very long (about half an hour or more). I tried to create an xfs and ext3 filesystem, both took a long time, with mkfs.ext3 I observed the following behaviour, which might be helpful: writing inode tables runs fast until it reaches 1053 (~ 1 second), then it writes about 50, waits for two seconds, then the next 50 are written (according to the console display) when I try to cancel the operation with Control+C it hangs for half a minute before it is really canceled The performance of the disks individually is very good, I've run bonnie++ on each one separately with write / read values of around 95 / 110MB/s. Even when I run bonnie++ on every drive in parallel the values are only reduced by about 10 MB. So I'm excluding hardware / I/O scheduling in general as a problem source. I tried different configuration parameters for stripe_cache_size and readahead size without success, but I don't think they are that relevant for the file system creation operation. The server details: Linux server 2.6.35-27-generic #48-Ubuntu SMP x86_64 GNU/Linux mdadm - v2.6.7.1 Does anyone has a suggestion on how to further debug this?

  Read the article

• Whats the easiest route to trying out mono 2.6?

  - by E J

  We have several web applications built on Microsoft technologies (asp.net+mvc framework, built using VS2008, MS SQL Server). I have recently be playing with Ubuntu (9.10), installed using Wubi, and wanted to see if I can get our apps running on a foss software stack. I have got the hang of the very basics of Postgresql and I have read that there is some support for Linq to SQL in mono (as of 2.6) as well as asp.net/MVC. However I am unsure how to go about getting Mono 2.6 up and running. Here is what I have discovered so far: Ubuntu is not meant for the 'cutting edge' it is designed to be stable hence, it sometimes takes a release cycle or two for new software to make it to the repositories Mono is already installed by default, but it is likely to stay at version 2.4 for at least the 10.4 release You can install paralell environments of Mono, if you know what your doing. I have had a go at setting up parallel environments, but haven't had any luck yet. (And TBH I am not certain that that will do what I think it's gonna do). (tl;dr start here) Is there a distribution of Linux similar enough to Ubuntu, that I wouldn't have to start the learning curve all over again, but that will let me install Mono 2.6, Postgresql, (and possibly mono-develop 2.4)? Or should I persist with Ubuntu?

  Read the article

• Keytool and SSL Apache config

  - by Safari

  I have a question about SSL certificate... I have generate a certificate using this keytool command.. keytool -genkey -alias myalias -keyalg RSA -keysize 2048 and I used this command to export the certificate keytool -export -alias myalias -file certificate.crt So, I have a file .crt Now I would to configure my Apache ssl module. I need to use keytool...At the moment I can't to use Openssl How can I configure the module if I have only this certificate.crt file? I see these sections in my ssl.conf # Server Certificate: # Point SSLCertificateFile at a PEM encoded certificate. If # the certificate is encrypted, then you will be prompted for a # pass phrase. Note that a kill -HUP will prompt again. A new # certificate can be generated using the genkey(1) command. #SSLCertificateFile /etc/pki/tls/certs/localhost.crt # Server Private Key: # If the key is not combined with the certificate, use this # directive to point at the key file. Keep in mind that if # you've both a RSA and a DSA private key you can configure # both in parallel (to also allow the use of DSA ciphers, etc.) #SSLCertificateKeyFile /etc/pki/tls/private/localhost.key # Server Certificate Chain: # Point SSLCertificateChainFile at a file containing the # concatenation of PEM encoded CA certificates which form the # certificate chain for the server certificate. Alternatively # the referenced file can be the same as SSLCertificateFile # when the CA certificates are directly appended to the server # certificate for convinience. #SSLCertificateChainFile /etc/pki/tls/certs/server-chain.crt How can I configure the correct section?

  Read the article

• Is this "cache administrator" error my server's problem?

  - by Eoin

  Hey, I have a CentOS VPS running Apache with a phpBB installation. One specific user has received errors when posting a message or logging in to the forum. The following issue has arisen in parallel to installing nginx, which serves only the static files of my site. Not sure if this is only coincidence. Furthermore, my setup uses redirects (in some cases, double-redirects) to point the user to a different virtual folder. So, the forum is seen to be at /translation/ but the actual files are found in /phpbb/. I'm at a loss as to what may be the underlying issue. My server? The person's ISP? She has tested both at home and at work, with similar issues. While trying to process the request: GET /phpbb/index.php?sid=f62c927e7eb8f1d60a92dcc6fd918112 HTTP/1.1 Host: www.irishgaelictranslator.com User-Agent: Mozilla/5.0 (Windows; U; Windows NT 5.1; en-GB; rv:1.9.2.13) Gecko/20101203 Firefox/3.6.13 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-za Accept-Encoding: gzip,deflate Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive: 115 Connection: keep-alive Referer: http://www.irishgaelictranslator.com/phpbb/ucp.php?mode=login Cookie: phpbb3_cipi4_u=96645; phpbb3_cipi4_k=; phpbb3_cipi4_sid=f62c927e7eb8f1d60a92dcc6fd918112; __utma=153470688.1232378553.1294664234.1294664234.1294664234.1; __utmb=153470688.9.10.1294664234; __utmc=153470688; __utmz=153470688.1294664235.1.1.utmcsr=(direct)|utmccn=(direct)|utmcmd=(none); style_cookie=null The following error was encountered: Invalid Response The HTTP Response message received from the contacted server could not be understood or was otherwise malformed. Please contact the site operator. Your cache administrator may be able to provide you with more details about the exact nature of the problem if needed.

  Read the article

• CUPS printer on Vritual Machine can be access via CUPS admin, but not by XP?

  - by SJaguar13

  I have a Zebra label printer connected to a Linux Mint virtual machine. It was set up with CUPS and a Windows XP computer can then print to it via http://192.168.1.76:632/printers/labelprinter. That was all fine and dandy I then hooked up a Fargo Pro L PVC card printer to a Windows XP virtual machine. I had to disconnect the label printer as the server that hosted both virtual machines only has 1 parallel port. Now I plugged in the Zebra again, and it cannot print from the Windows XP computer anymore. If I go to the CUPS admin panel on the Windows XP computer, I can see it, everything looks fine, and I can send it a test page to print which works. If I try to print from Windows, I get an error that the printer is not found/cannot connect to the server. The only other thing that changed was the firewall on the router to allow remote desktop to another computer from outside the network, but all the firewall stuff was for external use. Nothing affected the IP address of the internal network. The Linux Mint VM also had a PDF pritner that was shared with CUPS. That printer is also down. I tried setting up a new CUPS installation on another VM, and when I go to share it with XP, I get the same error. I don't know what to try. It has access, it can get to the admin from that computer, it seems to be up and ready, but when Windows tries to connect, the printer isn't found even though 4 days ago everything was fine. Any ideas?

  Read the article

• Is there a historical computer peripherals or accessories museum or even just a current list?

  - by zimmer62

  Thinking about all the unique and different peripherals I've owned over the years, from ISA capture cards, to parallel port controlled shutter glasses for 3d games. I've seen many many accessory or computer peripherals come and go. The nostalgia of these things is a lot of fun. I tried to find some sort of historical time-line or list but what mostly turned up is computers themselves. I'm more interested in the mice, scanners, the weird adapters that shouldn't exist, short run very rare products, strange devices from computer shows in the 80's and 90's... Hardware you might find in a geeks basement that would be completely useless now, but was the coolest thing around when it was new. An example would be a drawing tablet I had for my TI-99 computer, or the audio tape player accessory for a C64 which let you save files to audio tapes, An ISA card that did the same for PC's hooked up to a VCR. Remember that IBM-PC Jr upgrade kit, that added a floppy drive, more memory and the AT switch in the back? I'd love to find either a wiki, or a list that has already been assembled which contain many of these weird (or common) accessories. I've had so many over the years I suppose I could start a wiki here if such a list doesn't already exist.

  Read the article

• IIS 7.5 truncating POST body containing JSON data with ASP.NET MVC 3

  - by Guneet Sahai

  I'm facing a problem which I hope is a configuration thing with IIS but is right now giving a lot of trouble. Basically I have a controller that accepts a JSON and does some processing. While it generally works fine, but every now and then when the system has some load I get an error. After some painful debugging, we figured the incoming JSON gets truncated which causes the deserialzer to fail. To narrow down the problem - we wrote a simple controller that accepts a JSON and tries to deserialize it. In case it fails it just logs it. This works fine but when I hit it using a load testing tool (JMeter) it throws the same error (truncation) for a few requests. The # of failures increased when I increase parallel connections. It starts showing with 150 concurrent requests. We are running IIS 7 on windows 2008 server with ASP.Net MVC 3 with more or less default configuration of IIS. More information available in my question below http://stackoverflow.com/questions/12662282/content-length-of-http-request-body-size

  Read the article

• Why does clicking on Windows 7 Printer Properties Result In Driver Not Installed?

  - by octopusgrabbus

  The question I need to ask is has anyone heard of getting a "driver not installed" error when clicking on a printer's properties on Windows 7, and is there a workaround? Here are the details of the problem. One of our users has a Windows 7 desktop, and an HP LaserJet 4050 T connected to via a parallel-to-usb converter. The PLC5 universal driver was installed for series 4050 printers. I needed to install the PLC 6 driver, which completed successfully. The user is an administrator of the system, and I was prompted to and accepted running as Administrator to install the driver. After the install, I went to see the 4050's properties and was prompted that the PLC6 driver was not installed. I believe the PLC6 driver was installed, because the PLC5 driver resulted in receiving an official HP error page indicating the printer was "not set up for collating" as the second page of printing two copies of a one page email. This problem did not occur with the PLC 6 driver. Oddly enough, setting back to PLC5 produced the same error about the PLC5 driver not being installed. I ignored/dismissed the error box (did not re-install the driver), and reproduced the error, with the second page being the HP not set up for collating error page. Any thoughts on what is causing this and how to clear it would be appreciated. The closest fix I could find was on a Microsoft tech page, and they had me clear winsock out of a Administrator run command line, followed by a reboot. That did not fix the problem. I have also found this http://social.technet.microsoft.com/Forums/windowsserver/en-US/5101195b-3aca-4699-9a06-db4578614e2d/changing-driver-results-in-printer-driver-is-not-installed-error-on-server-2008?forum=winserverprint and will look into trying some of these suggestions, which appear to me to be a "shotgun" approach to fixing the problem.

  Read the article

• mkfs Operation Takes Very Long on Linux Software Raid 5

  - by Elmar Weber

  I've set-up a Linux software raid level 5 consisting of 4 * 2 TB disks. The disk array was created with a 64k stripe size and no other configuration parameters. After the initial rebuild I tried to create a filesystem and this step takes very long (about half an hour or more). I tried to create an xfs and ext3 filesystem, both took a long time, with mkfs.ext3 I observed the following behaviour, which might be helpful: writing inode tables runs fast until it reaches 1053 (~ 1 second), then it writes about 50, waits for two seconds, then the next 50 are written (according to the console display) when I try to cancel the operation with Control+C it hangs for half a minute before it is really canceled The performance of the disks individually is very good, I've run bonnie++ on each one separately with write / read values of around 95 / 110MB/s. Even when I run bonnie++ on every drive in parallel the values are only reduced by about 10 MB. So I'm excluding hardware / I/O scheduling in general as a problem source. I tried different configuration parameters for stripe_cache_size and readahead size without success, but I don't think they are that relevant for the file system creation operation. The server details: Linux server 2.6.35-27-generic #48-Ubuntu SMP x86_64 GNU/Linux mdadm - v2.6.7.1 Does anyone has a suggestion on how to further debug this?

  Read the article

• Building vs buying a server for an academic lab [closed]

  - by Roy

  I'm looking for advice on the classic build vs buy question. We need a new linux server to run Matlab computation on in our lab (academic). Matlab parallel computing toolbox licence allows up to 12 local workers so we are aiming at a 12 core server with 4GB memory per core (total of 48gb). The system will have an SSD for the OS and a raid-5 (4x2tb) for data. I looked around and found a (relatively) cheap vendor, Silicon Mechanics, that offers a system to our liking (specs below) for $6732. However, buying the components from newegg cost only $4464! The difference is $2268 which is 50% of the base cost. If buying from a company can be thought of as a sort of insurance, basically my premiums are of 50% of the base cost which to me sounds like a lot. Of course any downtime is bad, but the work is not "mission critical", i.e. if it takes a few days to fix it when it breaks its no the end of the world. If it takes weeks to months then its a problem. If it breaks 2-3 times in 3 years, not too bad. If it breaks every month not good. In term of build experience, I set up a linux cluster in grad school (from existing computers) and I build my home pcs but I never built a server before. The server components I'm thinking about: 1 x SUPERMICRO SYS-7046T-6F 4U Tower Server Barebone Dual LGA 1366 Intel 5520 DDR3 1333/1066/800 ($1,050) 12 x Kingston 4GB 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10600) ECC Unbuffered Server Memory ($420) 2 x Intel Xeon E5645 Westmere-EP 2.4GHz LGA 1366 80W Six-Core ($1,116) 4 x Seagate Constellation ES 2TB 7200 RPM SATA 6.0Gb/s 3.5" ($1,040) 1 x SAMSUNG Internal DVD Writer Black SATA ($20) 1 x Intel 520 Series 2.5" 180GB SATA III MLC SSD $300 1 x LSI LSI00281 PCI-Express 2.0 x8 MD2 Low profile SATA / SAS MegaRAID SAS 9260CV-4i Controller Card, $695

  Read the article

• What's throttling the database?

  - by Troels Arvin

  Hardware: Intel x86_64 with 192GB of RAM. OS: CentOS 5.4 x86_64. DBMS: DB2 v. 9.7.1 64 bit. During certain special workloads (e.g. parallel REORGs/RUNSTATs), I've seen the server transporting 450MB/s with 25000IO/s (yes, there is probably some storage system caching happening here) while all CPU cores were happily working in an even mix of usermode/wait. And disk benchmark tools can also bring some very satisfying bandwith and IO/s numbers to the table. On the other hand, we also have another scenario: A single rather complex query with at least one large table scan. db2's "list applications" reports that the query is Executing (not locked). IO: At most 10MB/s, 500 IO/s; CPU: two cores in 99.9% wait state, all other cores 100% idle. The tables which the query reads from have been altered to have LOCKSIZE=TABLE, so I would think that lock list work is zero. What's going on in such a situation? What tools/snapshots/... can I use to gain better insight in such a case?

  Read the article

• DD-WRT Acces Point as a Router

  - by Dzh

  Following suggestion to this question asked on Network Engineering, I am asking the question here. this is an extension to my previous question (I think it was deleted), where I was claiming that DDWRT was disabling it's DHCP server once connected to the network. I was wrong, as it now seems that it is bridging itself with another parallel connected wireless router. I have two Draytek 2820 and one Netgear WG602v3 with latest DDWRT. Lets call one wired-Draytek and it has wireless disabled. The other one, let's call it wireless-Draytek, is connected to wired-Draytek and has wireless with MAC filtering enabled. Once I connect Netgear to the wired-Draytek, the client that connects to Netgear, will be assigned with IP address from the wireless-Draytek. If the MAC address is not on the wireles-Draytek, the client is unable to obtain IP address and has no connectivity at all, even with manually assigned static IP configuration. To illustrate further, this is how network is set up: wired-Draytek ---------- wireless-Draytek \_________ Netgear What I wish to have, is that Netgear issues IP addresses from it's own IP pool and ignores the MAC filtering rules from wireless-Draytek. This is kind of puzzling how this they are bridging (if they are) themselves automatically. Thanks. UPDATE: It's not a home network. I gave you a bit simplified set-up. If there is a better site on Stack Exchange to ask this, please let me know. The Drayteks are running stock firmware, it's only Netgear that I've flashed to get more stability. In addition to these routers, I have also three 3COM Baseline switch 2824, and another Draytek router with Prosafe FS752TP PoE switch dedicated for VoIP phones. Wired-Draytek has IP 10.0.0.1, DHCP disabled as there is AD DC which is issuing IP addresses. Wireless-Draytek has IP 1.1.1.1 and DHCP enabled. Netgear has default - 192.168.1.1. As per suggestion, the specific question is - how do I isolate these two wireless routers?

  Read the article

• Can I boot up a virtual machine natively?

  - by Anshul

  My question is: Is is possible to run a virtual machine natively on your hardware if you have installed the proper drivers etc? In other words, can I use a VHD as a regular hard drive to boot from? The reason I want to do this is that I do both graphics-intensive and audio-intensive work, but my computer is not powerful enough to handle both at the same time and many times I install a bunch of audio programs that I don't want affecting the stability of my graphics programs. Basically I wanted to have sandboxing between the two sets of applications. So I tried running the graphics-intensive programs in a VirtualBox VM and the audio-intensive work natively (simply because it's a pain to route ASIO audio devices in/out of VirtualBox). This kind-of works - the graphics-intensive stuff is tolerable, but still relatively slow, because it's running inside a VM. So my next idea was to just dual-boot and install the graphics and audio programs in separate partitions but I frequently use them in tandem, so it wouldn't be practical to reboot my machine every time I need to use the other set of programs. But I could live with this scenario: If I need to do more audio-intensive stuff, I'll just boot up to the audio partition and run the graphics programs in a VM, and then when I'm working heavily on the graphics part, I'll just boot the graphics partition as a regular OS directly on the hardware. Is this possible? For example by booting up a VHD as a regular hard drive? Or by setting up dual-boot, and every time the audio partition is shut down, synchronize the graphics VM VHD with the native graphics partition? Is it practical, given the above scenario? And if it's not possible, barring buying another computer, can anyone suggest a best-of-all-worlds setup (the two worlds being performance, sandboxing, and running in parallel) for the above scenario? Thanks in advance.

  Read the article

< Previous Page | 50 51 52 53 54 55 56 57 58 59 60 61  | Next Page >