Search Results

Search found 1593 results on 64 pages for 'sha 256'.

Page 54/64 | < Previous Page | 50 51 52 53 54 55 56 57 58 59 60 61  | Next Page >

• Proliant server will not accept new hard disks in RAID 1+0?

  - by Leigh

  I have a HP ProLiant DL380 G5, I have two logical drives configured with RAID. I have one logical drive RAID 1+0 with two 72 gb 10k sas 1 port spare no 376597-001. I had one hard disk fail and ordered a replacement. The configuration utility showed error and would not rebuild the RAID. I presumed a hard disk fault and ordered a replacement again. In the mean time I put the original failed disk back in the server and this started rebuilding. Currently shows ok status however in the log I can see hardware errors. The new disk has come and I again have the same problem of not accepting the hard disk. I have updated the P400 controller with the latest firmware 7.24 , but still no luck. The only difference I can see is the original drive has firmware 0103 (same as the RAID drive) and the new one has HPD2. Any advice would be appreciated. Thanks in advance Logs from server ctrl all show config Smart Array P400 in Slot 1 (sn: PAFGK0P9VWO0UQ) array A (SAS, Unused Space: 0 MB) logicaldrive 1 (68.5 GB, RAID 1, Interim Recovery Mode) physicaldrive 2I:1:1 (port 2I:box 1:bay 1, SAS, 73.5 GB, OK) physicaldrive 2I:1:2 (port 2I:box 1:bay 2, SAS, 72 GB, Failed array B (SAS, Unused Space: 0 MB) logicaldrive 2 (558.7 GB, RAID 5, OK) physicaldrive 1I:1:5 (port 1I:box 1:bay 5, SAS, 300 GB, OK) physicaldrive 2I:1:3 (port 2I:box 1:bay 3, SAS, 300 GB, OK) physicaldrive 2I:1:4 (port 2I:box 1:bay 4, SAS, 300 GB, OK) ctrl all show config detail Smart Array P400 in Slot 1 Bus Interface: PCI Slot: 1 Serial Number: PAFGK0P9VWO0UQ Cache Serial Number: PA82C0J9VWL8I7 RAID 6 (ADG) Status: Disabled Controller Status: OK Hardware Revision: E Firmware Version: 7.24 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 15 secs Surface Scan Mode: Idle Wait for Cache Room: Disabled Surface Analysis Inconsistency Notification: Disabled Post Prompt Timeout: 0 secs Cache Board Present: True Cache Status: OK Cache Status Details: A cache error was detected. Run more information. Cache Ratio: 100% Read / 0% Write Drive Write Cache: Disabled Total Cache Size: 256 MB Total Cache Memory Available: 208 MB No-Battery Write Cache: Disabled Battery/Capacitor Count: 0 SATA NCQ Supported: True Array: A Interface Type: SAS Unused Space: 0 MB Status: Failed Physical Drive Array Type: Data One of the drives on this array have failed or has Logical Drive: 1 Size: 68.5 GB Fault Tolerance: RAID 1 Heads: 255 Sectors Per Track: 32 Cylinders: 17594 Strip Size: 128 KB Full Stripe Size: 128 KB Status: Interim Recovery Mode Caching: Enabled Unique Identifier: 600508B10010503956574F305551 Disk Name: \\.\PhysicalDrive0 Mount Points: C:\ 68.5 GB Logical Drive Label: A0100539PAFGK0P9VWO0UQ0E93 Mirror Group 0: physicaldrive 2I:1:2 (port 2I:box 1:bay 2, S Mirror Group 1: physicaldrive 2I:1:1 (port 2I:box 1:bay 1, S Drive Type: Data physicaldrive 2I:1:1 Port: 2I Box: 1 Bay: 1 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 73.5 GB Rotational Speed: 10000 Firmware Revision: 0103 Serial Number: B379P8C006RK Model: HP DG072A9B7 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:2 Port: 2I Box: 1 Bay: 2 Status: Failed Drive Type: Data Drive Interface Type: SAS Size: 72 GB Rotational Speed: 15000 Firmware Revision: HPD9 Serial Number: D5A1PCA04SL01244 Model: HP EH0072FARUA PHY Count: 2 PHY Transfer Rate: Unknown, Unknown Array: B Interface Type: SAS Unused Space: 0 MB Status: OK Array Type: Data Logical Drive: 2 Size: 558.7 GB Fault Tolerance: RAID 5 Heads: 255 Sectors Per Track: 32 Cylinders: 65535 Strip Size: 64 KB Full Stripe Size: 128 KB Status: OK Caching: Enabled Parity Initialization Status: Initialization Co Unique Identifier: 600508B10010503956574F305551 Disk Name: \\.\PhysicalDrive1 Mount Points: E:\ 558.7 GB Logical Drive Label: AF14FD12PAFGK0P9VWO0UQD007 Drive Type: Data physicaldrive 1I:1:5 Port: 1I Box: 1 Bay: 5 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 300 GB Rotational Speed: 10000 Firmware Revision: HPD4 Serial Number: 3SE07QH300009923X1X3 Model: HP DG0300BALVP Current Temperature (C): 32 Maximum Temperature (C): 45 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:3 Port: 2I Box: 1 Bay: 3 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 300 GB Rotational Speed: 10000 Firmware Revision: HPD4 Serial Number: 3SE0AHVH00009924P8F3 Model: HP DG0300BALVP Current Temperature (C): 34 Maximum Temperature (C): 47 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:4 Port: 2I Box: 1 Bay: 4 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 300 GB Rotational Speed: 10000 Firmware Revision: HPD4 Serial Number: 3SE08NAK00009924KWD6 Model: HP DG0300BALVP Current Temperature (C): 35 Maximum Temperature (C): 47 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown

  Read the article

• what is best config for nginx worker_rlimit_nofile and worker_connections 28672

  - by Binh Nguyen

  i have issue of web-brower response ( especially on ie ) very slow, some time time out, and sometime hang out up to 20 seconds for one file redirect 301 when test with "f12 derverloper tool of ie" .. it report wait/start time very long. but after got connected the elements on web weill be dowload and show out fast ( test at xaluan.com ) It most happen when active user on web more than 2100 ( use google real time live analytic ). server running cenos 5 with ngix, apache, 32core cpu, 96G ram, raid 10 sas hdd.. == flowing is my config == user nobody; # no need for more workers in the proxy mode worker_processes 28; #old 32 #good at 24 error_log /var/log/nginx/error.log; #old add in end: info worker_rlimit_nofile 22528; events { worker_connections 22528; use epoll; # you should use epoll here for Linux kernels 2.6.x } http { server_name_in_redirect off; server_names_hash_max_size 10240; server_names_hash_bucket_size 1024; include mime.types; default_type application/octet-stream; server_tokens off; disable_symlinks off; sendfile on; tcp_nopush on; tcp_nodelay on; server_name_in_redirect off; server_names_hash_max_size 10240; server_names_hash_bucket_size 1024; include mime.types; default_type application/octet-stream; server_tokens off; disable_symlinks off; sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 25; #old 5 gzip on; #old on gzip_vary on; gzip_disable "MSIE [1-6]\."; gzip_proxied any; gzip_http_version 1.1; gzip_min_length 1000; gzip_comp_level 6; gzip_buffers 16 8k; ignore_invalid_headers on; client_header_timeout 1m; #3m client_body_timeout 1m; #3m send_timeout 1m; #3m reset_timedout_connection on; connection_pool_size 256; client_header_buffer_size 256k; large_client_header_buffers 4 256k; client_max_body_size 100M; client_body_buffer_size 256k; request_pool_size 32k; output_buffers 4 32k; postpone_output 1460; proxy_temp_path /tmp/nginx_proxy/; client_body_in_file_only on; log_format bytes_log "$msec $bytes_sent ."; limit_conn_zone $binary_remote_addr zone=limit_per_ip:1m; limit_conn limit_per_ip 20; limit_req_zone $binary_remote_addr zone=allips:5m rate=200r/s; limit_req zone=allips burst=200 nodelay; include "/etc/nginx/vhosts/*"; } =========== I have play around with worker config 1- tried increase as some one suggess: worker_rlimit_nofile = worker_connections = worker_processes * 1024 = 32768 2- tried to set low: worker_processes = 28 and other worker at 22582 and other solution too .. but not work cause some time it make server load hight very quick 3- tried to comment out the # worker_rlimit_nofile . so it will be unlimited. it look like solved a bit about issue response time. but it also make server high load quick in peak time... Please help thanks PS: other apache you may have look for help me out thanks Listen 0.0.0.0:8081 User nobody Group nobody ExtendedStatus On ServerAdmin [email protected] ServerName server.xaluan.com LogLevel warn # These can be set in WHM under 'Apache Global Configuration' Timeout 100 TraceEnable Off ServerSignature Off ServerTokens ProductOnly FileETag None StartServers 15 <IfModule prefork.c> MinSpareServers 20 MaxSpareServers 50 #MaxSpareServers 40 </IfModule> ServerLimit 1572 MaxClients 1572 MaxRequestsPerChild 4000 # MaxRequestsPerChild 3000 KeepAlive On KeepAliveTimeout 3 MaxKeepAliveRequests 300 #MaxKeepAliveRequests 130

  Read the article

• Squid not caching files (Randomly)

  - by Heinrich

  I want to use an intercepting squid server to cache specific large zip files that users in my network download frequently. I have configured squid on a gateway machine and caching is working for "static" zip files that are served from an Apache web server outside our network. The files that I want to have cached by squid are zip files 100MB which are served from a heroku-hosted Rails application. I set an ETag header (SHA hash of the zip file on the server) and Cache-Control: public header. However, these files are not cached by squid. This, for example, is a request that is not cached: $ curl --no-keepalive -v -o test.zip --header "X-Access-Key: 20767ed397afdea90601fda4513ceb042fe6ab4e51578da63d3bc9b024ed538a" --header "X-Customer: 5" "http://MY_APP.herokuapp.com/api/device/v1/media/download?version=latest" * Adding handle: conn: 0x7ffd4a804400 * Adding handle: send: 0 * Adding handle: recv: 0 ... > GET /api/device/v1/media/download?version=latest HTTP/1.1 > User-Agent: curl/7.30.0 > Host: MY_APP.herokuapp.com > Accept: */* > X-Access-Key: 20767ed397afdea90601fda4513ceb042fe6ab4e51578da63d3bc9b024ed538a > X-Customer: 5 > 0 0 0 0 0 0 0 0 --:--:-- 0:00:09 --:--:-- 0< HTTP/1.1 200 OK * Server Cowboy is not blacklisted < Server: Cowboy < Date: Mon, 18 Aug 2014 14:13:27 GMT < Status: 200 OK < X-Frame-Options: SAMEORIGIN < X-Xss-Protection: 1; mode=block < X-Content-Type-Options: nosniff < ETag: "95e888938c0d539b8dd74139beace67f" < Content-Disposition: attachment; filename="e7cce850ae728b81fe3f315d21a560af.zip" < Content-Transfer-Encoding: binary < Content-Length: 125727431 < Content-Type: application/zip < Cache-Control: public < X-Request-Id: 7ce6edb0-013a-4003-a331-94d2b8fae8ad < X-Runtime: 1.244251 < X-Cache: MISS from AAA.fritz.box < Via: 1.1 vegur, 1.1 AAA.fritz.box (squid/3.3.11) < Connection: keep-alive In the logs squid is reporting a TCP_MISS. This is the relevant excerpt from my squid file: # Squid normally listens to port 3128 http_port 3128 http_port 3129 intercept # Uncomment and adjust the following to add a disk cache directory. maximum_object_size 1000 MB maximum_object_size_in_memory 1000 MB cache_dir ufs /usr/local/var/cache/squid 10000 16 256 cache_mem 2000 MB # Leave coredumps in the first cache dir coredump_dir /usr/local/var/cache/squid cache_store_log daemon:/usr/local/var/logs/cache_store.log #refresh_pattern -i (/cgi-bin/|\?) 0 0% 0 refresh_pattern -i .(zip) 525600 100% 525600 override-expire ignore-no-cache ignore-no-store refresh_pattern . 0 20% 4320 ## DNS Configuration dns_nameservers 8.8.8.8 8.8.4.4 After trying around for some time I realized that squid is sometimes deciding that my file is cacheable, sometimes not, depending on whether and when I enable/disable the dns_nameservers directive. What could be wrong here?

  Read the article

• libvirt upgrade caused vms to not see drives (boot media not found)

  - by bias

  I upgraded to Ubuntu 12.04.1 and now libvirt (via open nebula) successfully runs vms but they aren't finding the 2 drives (specifically, the boot drive). One is "hd" the other is "cdrom". The machine boots but fails and displays something like "boot media not found hd" (this was in a vnc terminal and I didn't copy the output anywhere so that's not the verbatim message). I tried constructing a new disk using the new version of qemu (via vmbuilder) and this new machine has the same problem as the old machine. In case it matters (I can't see why it would) I'm using open nebula to manage the machines. There's nothing relevant in any of the logs: syslog, libvirtd, oned. Which is to say nothing interesting/anomalous is reported when the machine is brought up. Versions libvirt 0.9.8-2ubuntu17.4 qemu-kvm 1.0+noroms-0ubuntu14.3 The libvirt xml config portions (relavent) <os> <type arch='x86_64' machine='pc-1.0'>hvm</type> <boot dev='hd'/> </os> ... <devices> <emulator>/usr/bin/kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='qcow2'/> <source file='/var/lib/one//203/images/disk.0'/> <target dev='sda' bus='scsi'/> <alias name='scsi0-0-0'/> <address type='drive' controller='0' bus='0' unit='0'/> </disk> <disk type='file' device='cdrom'> <driver name='qemu' type='raw'/> <source file='/var/lib/one//203/images/disk.1'/> <target dev='sdc' bus='scsi'/> <readonly/> <alias name='scsi0-0-2'/> <address type='drive' controller='0' bus='0' unit='2'/> </disk> <controller type='scsi' index='0'> <alias name='scsi0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x05' function='0x0'/> </controller> <memballoon model='virtio'> <alias name='balloon0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x06' function='0x0'/> </memballoon> ... </devices> The libvirt/qemu log contains 2012-11-25 22:19:24.328+0000: starting up LC_ALL=C PATH=/usr/local/sbin:/usr/local/bin:/usr/bin:/usr/sbin:/sbin:/bin QEMU_AUDIO_DRV=none /usr/bin/kvm -S -M pc-1.0 -enable-kvm -m 256 -smp 1,sockets=1,cores=1,threads=1 -name one-204 -uuid 4be6c276-19e8-bdc2-e9c9-9ca5352f2be3 -nodefconfig -nodefaults -chardev socket,id=charmonitor,path=/var/lib/libvirt/qemu/one-204.monitor,server,nowait -mon chardev=charmonitor,id=monitor,mode=control -rtc base=utc -no-shutdown -device lsi,id=scsi0,bus=pci.0,addr=0x5 -drive file=/var/lib/one//204/images/disk.0,if=none,id=drive-scsi0-0-0,format=qcow2 -device scsi-disk,bus=scsi0.0,scsi-id=0,drive=drive-scsi0-0-0,id=scsi0-0-0,bootindex=1 -drive file=/var/lib/one//204/images/disk.1,if=none,media=cdrom,id=drive-scsi0-0-2,readonly=on,format=raw -device scsi-disk,bus=scsi0.0,scsi-id=2,drive=drive-scsi0-0-2,id=scsi0-0-2 -netdev tap,fd=18,id=hostnet0 -device rtl8139,netdev=hostnet0,id=net0,mac=02:00:c0:a8:00:68,bus=pci.0,addr=0x3 -netdev tap,fd=19,id=hostnet1 -device rtl8139,netdev=hostnet1,id=net1,mac=02:00:ad:f0:1b:94,bus=pci.0,addr=0x4 -usb -vnc 0.0.0.0:204 -vga cirrus -device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x6 kvm: -device rtl8139,netdev=hostnet0,id=net0,mac=02:00:c0:a8:00:68,bus=pci.0,addr=0x3: pci_add_option_rom: failed to find romfile "pxe-rtl8139.rom" kvm: -device rtl8139,netdev=hostnet1,id=net1,mac=02:00:ad:f0:1b:94,bus=pci.0,addr=0x4: pci_add_option_rom: failed to find romfile "pxe-rtl8139.rom"

  Read the article

• Can't configure frame relay T1 on Cisco 1760

  - by sonar

  For the past few days I've been trying to configure a data T1 via a Frame Relay. Now I've been pretty unsuccessful at it, and it's been a while, since I've done this so please bare with me. The ISP provided me the following information: 1. IP address 2. Gateway address 3. Encapsulation Frame Relay 4. DLCI 100 5. BZ8 ESF (I think the bz8 was supposed to be b8zs) 6. Time Slot (1 al 24). And what I have configured up until now is the following: interface Serial0/0 ip address <ip address> 255.255.255.252 encapsulation frame-relay service-module t1 timeslots 1-24 frame-relay interface-dlci 100 sh service-module s0/0 (outputs): Module type is T1/fractional Hardware revision is 0.128, Software revision is 0.2, Image checksum is 0x73D70058, Protocol revision is 0.1 Receiver has no alarms. Framing is **ESF**, Line Code is **B8ZS**, Current clock source is line, Fraction has **24 timeslots** (64 Kbits/sec each), Net bandwidth is 1536 Kbits/sec. Last module self-test (done at startup): Passed Last clearing of alarm counters 00:17:17 loss of signal : 0, loss of frame : 0, AIS alarm : 0, Remote alarm : 2, last occurred 00:10:10 Module access errors : 0, Total Data (last 1 15 minute intervals): 0 Line Code Violations, 0 Path Code Violations 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs Data in current interval (138 seconds elapsed): 0 Line Code Violations, 0 Path Code Violations 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs sh int: FastEthernet0/0 is up, line protocol is up Hardware is PQUICC_FEC, address is 000d.6516.e5aa (bia 000d.6516.e5aa) Internet address is 10.0.0.1/24 MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, 100BaseTX/FX ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:20:00, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog 0 input packets with dribble condition detected 191 packets output, 20676 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out Serial0/0 is up, line protocol is down Hardware is PQUICC with Fractional T1 CSU/DSU MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation FRAME-RELAY, loopback not set Keepalive set (10 sec) LMI enq sent 157, LMI stat recvd 0, LMI upd recvd 0, DTE LMI down LMI enq recvd 23, LMI stat sent 0, LMI upd sent 0 LMI DLCI 1023 LMI type is CISCO frame relay DTE FR SVC disabled, LAPF state down Broadcast queue 0/64, broadcasts sent/dropped 2/0, interface broadcasts 0 Last input 00:24:51, output 00:00:05, output hang never Last clearing of "show interface" counters 00:27:20 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/1/256 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) Available Bandwidth 1152 kilobits/sec 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 23 packets input, 302 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 1725 input errors, 595 CRC, 1099 frame, 0 overrun, 0 ignored, 30 abort 246 packets output, 3974 bytes, 0 underruns 0 output errors, 0 collisions, 48 interface resets 0 output buffer failures, 0 output buffers swapped out 4 carrier transitions DCD=up DSR=up DTR=up RTS=up CTS=up Serial0/0.1 is down, line protocol is down Hardware is PQUICC with Fractional T1 CSU/DSU MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation FRAME-RELAY Last clearing of "show interface" counters never Serial0/0.100 is down, line protocol is down Hardware is PQUICC with Fractional T1 CSU/DSU Internet address is <ip address>/30 MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation FRAME-RELAY Last clearing of "show interface" counters never And everything seems to be accounted for to me, but apparently I'm missing something. My issue is that I'm stuck on interface up, line protocol down, so the T1 doesn't go up. Any ideas? Thank you,

  Read the article

• CodePlex Daily Summary for Friday, March 12, 2010

  CodePlex Daily Summary for Friday, March 12, 2010New Projects.NET DEPENDENCY INJECTION: Abel Perez Enterprise FrameworkAutodocs - WCF REST Automatic API Documentation Generator: Autodocs is an automatic API documentation generator for .NET applications that use Windows Communication Foundation (WCF) to establish REST API's.BlockBlock: Block Block is a free game. You know Lumines and you will like BlockBlock.C4F XNA ASCII Post-Processing: This is the source code for the Coding4Fun article "XNA Effects – ASCII Art in 3D"ChequePrinter: this is ChequePrinterCompiladores MSIL usando Phoenix (PLP 2008.1 - CIn/UFPE): Este projeto foi feito com o intuito de explorar a plataforma Microsoft Phoenix para a construção de compiladores para MSIL de duas linguagens de E...CRM External View: CRM External View enables more robust control over exposing Microsoft CRM data (in a form of views) for external parties. The solution uses web ser...CS Project2: This is for the projectDotNetNuke IM Module of Facebook Like Messenger: Help you integrate 123 Web Messenger into DotNetNuke, and add a powerful 1-to-1 IM Software named "Facebook Messenger Style Web Chat Bar" at the bo...DotNetNuke® RadPanelBar: DNNRadPanelBar makes it easy to add telerik RadPanelBar functionality to your module or skin. Licensing permits anyone to use the components (incl...DotNetNuke® Skin Blocks: A DotNetNuke Design Challenge skin package submitted to the "Modern Business" category by Armand Datema of Schwingsoft. This skin uses a bit of jQu...Drilltrough and filtering on SSAS-cubes in SSRS: We will describe a technique to create Reporting services (SSRS) reports that use Analysis services (SSAS) cubes as data sources, have a very intu...Ecosystem Diagnosis & Treatment: The Ecosystem DIagnosis & Treatment community provides tools, analyses and applications of the medical model to natural resource problems. EDT sof...ExIf 35: A utility for use by film photographers for keeping track of critical facts about images taken on a roll of film, just as digital cameras do automa...FabricadeTI: Desenvolvimento do framework FabricadeTI.Find and Replace word in the sentences: This program used Java Development Kid 6.0 and i were using HighLighter class. It was completed code with source code and then everybody can use in...Flash Nut: Flash Nut is a flash card program. You can build and review decks of flash cards. The project is a vs2008 wpf application.Free DotNetNuke Chat Module (Popup Mode): With this free DotNetNuke Chat Module (Popup Mode), master will assist to integrate DotNetNuke with 123 Flash Chat seamlessly, and add a popup mode...Free DotNetNuke IM of 123 Web Messenger -- Web-based Friend List: With this FREE application, you could integrate DNN website Database with 123 Web Messenger seamlessly and embed a web-based Friends List into anyw...Free DotNetNuke Live Help Module: With DotNetNuke Live Help Module, integrate 123 Live Help into DotNetNuke website and add Live Chat Button anywhere you like. Let visitors to chat ...G52GRP Videowall: NottinghamHappy Turtle Plugins for BVI :: Repository Based Versioning for Visual Studio: The Happy Turtle project creates plugins for the Build Version Increment Add-In for Visual Studio (BVI). The focus is to automatically version asse...Hasher: Hasher es capaz de generar el hash MD5 y SHA de textos de hasta 100.000 caracteres y ficheros. También te permitirá comprobar dos hash para verifi...Infragistics Silverlight Extended Controls: This project is a group of controls that extend or add functionality to the Infragistics Silverlight control suite. This control requires Infragis...Insert Video Jnr: This is a baby version of my Video plugin, it is intended for Hosted Wordpress blogs only and shouldn't be used with other blog providers.jccc .NET smart framework: jccc .NET smart framework allows the creation of fast connections to MSSQL or MYSQL databases, and the data manipulation by using of c# class's tha...LytScript: 函数式脚本语言Microsoft - DDD NLayerApp .NET 4.0 Example (Microsoft Spain): DDD NLayered App .NET 4.0 Example By Microsoft - Spain Domain Driven Design NLayered App .NET 4.0 Example Implementation Example of our local Arc...mimiKit: Lightweight ASP.NET MVC / Javascript Framework for creating mobile applications PHPWord: With PHPWord you can easily create a Word document with PHP. PHPWord creates docx Files that can include all major word functions like TextElements...Protocol Transition with BizTalk: An example solution the shows how todo Protocol Transition with BizTalk. This also shows you how to create a WCF extension to allow this to happen.Raid Runner: Raid Runner makes it easier to run and manage raid in World of Warcraft. It is a Silverlight application developed in c#SQL Server Authentication Troubleshooter: SQL Server Authentication Troubleshooter is a tool to help investigate a root cause of ‘Login Failed’ error in SQL Server. There could be number of...SuperviseObjects: SuperviseObjects consists of a collection which is derived from ObservableCollection<T>. This collection fires ItemPropertyChanging and ItemPropert...Viuto: Viuto.NET project aims to create a fully track and trace application. It is developed in: - Java & C: Firmware - C#: Parser - Asp.net: Tracki...Zealand IT MSBuild Tasks: Zealand IT MSBuild Tasks is a collection that you cannot do without if you are serious about continous integration. Ever wish you could specify an...New ReleasesASP.NET: ASP.NET MVC 2 RTM: This release contains the source code for ASP.NET MVC 2 RTM as well as the ASP.NET MVC Futures project. The futures project contains features that ...C#Mail: Higuchi.Mail.dll (2010.3.11 ver): Higuchi.Mail.dll at 2010-3-11 version.C#Mail: Higuchi.MailServer.dll (2010.3.11 ver): Higuchi.MailServer.dll at 2010.3.11 version.C4F XNA ASCII Post-Processing: XNA ASCII FPS v1 - Full Version: This is the full, complete example of the XNA ASCII FPS.C4F XNA ASCII Post-Processing: XNA ASCII FPS v1.0 - Base Project: This is the base project to be used by those who plan to follow along the Coding4Fun article.CRM External View: 1.0: Release 1.0DevTreks -social budgeting that improves lives and livelihoods: Social Budgeting Web Software, DevTreks alpha 3c: Alpha 3c upgrades custom/virtual uris (devpacks), temp uris, and zip packages. This is believed to be the first fully functional/performant release.DotNetNuke® RadPanelBar: DNNRadPanelBar 1.0.0: DNNRadPanelBar makes it easy to add telerik RadPanelBar functionality to your module or skin. Licensing permits anyone to use the components (inclu...Drilltrough and filtering on SSAS-cubes in SSRS: Release 1: Release 1ExIf 35: ExIf 35: Daily build of ExIf 35Family Tree Analyzer: Version 1.0.3.0: Version 1.0.3.0 Added options to check for updates on load and on help menu Disable use of US census for now until dealt with years being differen...Family Tree Analyzer: Version 1.0.4.0: Version 1.0.4.0 Added support for display of Ahnenfatel numbers Added filter to hide individuals from Lost Cousins report that have been flagged a...Flash Nut: Flash Nut 1.0 Setup: Flash Nut SetupFluent Validation for .NET: 1.2 RC: This is the release candidate for FluentValidation 1.2. If no bugs are found within the next couple of weeks, then this will become the 1.2 Final b...Free DotNetNuke Chat Module (Popup Mode): Download DNN Chat Module (Popup Mode)+Source Code: Feel free to download DotNetNuke Chat Module (Popup Mode), integrating DotNetNuke with 123 Flash Chat Software, and add a free popup mode flash cha...Free DotNetNuke Live Help Module: Download DNN Live Support Module and Source Code: In Readme file, there are detailed Installation and Integration Manual for you. This module is compatible with DotNetNuke v5.x.Happy Turtle Plugins for BVI :: Repository Based Versioning for Visual Studio: Happy Turtle 1.0.44927: This is the first release of the SVN based version incrementor. How To InstallMake sure that Build Version Increment v2.2.10065.1524 or newer is i...Hasher: 1.0: Versión inicial de la aplicación: Obtención de hash MD5 y SHA. Codificación en tiempo real de textos de hasta 100.000 caracteres. Codificación ...Jamolina: PhotosynthDemo: PhotosynthDemoMapWindow GIS: MapWindow 6.0 msi (March 11): This fixes an PixelToProj problem for the Extended Buffer case, as well as adding fixes to the WKBFeatureReader to fix an X,Y reversal and some ext...Math.NET Numerics: 2010.3.11.291 Build: Latest alpha buildMicrosoft - DDD NLayerApp .NET 4.0 Example (Microsoft Spain): V0.5 - N-Layer DDD Sample App: Required Software (Microsoft Base Software needed for Development environment) Unity Application Block 1.2 - October 2008 http://www.microsoft.com/...MiniTwitter: 1.09.2: MiniTwitter 1.09.2 更新内容 修正 タイムラインを削除すると落ちるバグを修正 稀にタイムラインのスクロールが出来ないバグを修正Nestoria.NET: Nestoria.NET 0.8: Provides access to the Nestoria API. Documentation contains a basic getting started guide. Please visit Darren Edge's blog for ongoing developmen...Pod Thrower: Version 1.0: Here is version 1.0. It has all the features I was looking to do in it. Please let me know if you use this and if you would like any changes.SharePoint Ad Rotator: SPAdRotator 2.0 Beta: This new release of the Ad Rotator contains many new features. One major new feature is that jQuery has been added to do image rotation without hav...SharePoint Objects: Democode Ton Stegeman: These download contains sample code for some SharePoint 2007 blog posts: TST.Themes_Build20100311.zip contains a feature receiver that registers Sh...SharePoint Taxonomy Extensions: SharePoint Taxonomy Extensions 1.2: Make Taxonomy Extensions useable in every list type. Not only in document libraries.SharePoint Video Player Web Part & SharePoint Video Library: Version 3.0.0: Absolutely killer feature - installing multiple players on a page without any loss of performance.SilverLight Interface for Mapserver: SLMapViewer v. 1.0: SLMapviewer sample application version 1.0. This new release includes the following enhancements: Silverlight 3.0 native Added a new init parame...Spark View Engine: Spark v1.1: Changes since RC1Built against ASP.NET MVC 2 RTMSPSS .NET interop library: 2.0: This new version supports SPSS 15, and includes spssio32.dll and other native .dll dependencies so that it works out of the box without SPSS being ...stefvanhooijdonk.com: SharePoint2010.ProfilePicturesLoader: So, with the help of Reflector, I wrote a small tool that would import all our profile pictures and update the user profiles. http://wp.me/pMnlQ-6G SuperviseObjects: SuperviseObjects 1.0: First releaseTortoiseSVN Addin for Visual Studio: TortoiseSVN Addin 1.0.5: Feature: Visual Studio/svn action synchronization on Item in Solution explorer like add, move, delete and rename. Note: Move action does not rememb...VCC: Latest build, v2.1.30311.0: Automatic drop of latest buildVivoSocial: VivoSocial 7.0.4: Business Management ■This release fixes a Could not load type error on the main view of the module. Groups ■Group requests were failing in some i...WikiPlex – a Regex Wiki Engine: WikiPlex 1.3: Info: Official Version: 1.3.0.215 | Full Release Notes Documentation - This new documentation includes Full Markup Guide with Examples Articles ...Zealand IT MSBuild Tasks: Zealand IT MSBuild Tasks: Initial beta release of Zealand IT MSBuild Tasks. Contains the following tasks: RunAs - Same as Exec task, but provides parameters for impersonat...ZoomBarPlus: V1 (Beta): This is the initial release. It should be considered a beta test version as it has not been tested for very long on my device.Most Popular ProjectsMetaSharpWBFS ManagerRawrAJAX Control ToolkitMicrosoft SQL Server Product Samples: DatabaseSilverlight ToolkitWindows Presentation Foundation (WPF)ASP.NET Ajax LibraryASP.NETMicrosoft SQL Server Community & SamplesMost Active ProjectsUmbraco CMSRawrN2 CMSBlogEngine.NETFasterflect - A Fast and Simple Reflection APIjQuery Library for SharePoint Web Servicespatterns & practices – Enterprise LibraryFarseer Physics EngineCaliburn: An Application Framework for WPF and SilverlightSharePoint Team-Mailer

  Read the article

• Elfsign Object Signing on Solaris

  - by danx

  Elfsign Object Signing on Solaris Don't let this happen to you—use elfsign! Solaris elfsign(1) is a command that signs and verifies ELF format executables. That includes not just executable programs (such as ls or cp), but other ELF format files including libraries (such as libnvpair.so) and kernel modules (such as autofs). Elfsign has been available since Solaris 10 and ELF format files distributed with Solaris, since Solaris 10, are signed by either Sun Microsystems or its successor, Oracle Corporation. When an ELF file is signed, elfsign adds a new section the ELF file, .SUNW_signature, that contains a RSA public key signature and other information about the signer. That is, the algorithm used, algorithm OID, signer CN/OU, and time stamp. The signature section can later be verified by elfsign or other software by matching the signature in the file agains the ELF file contents (excluding the signature). ELF executable files may also be signed by a 3rd-party or by the customer. This is useful for verifying the origin and authenticity of executable files installed on a system. The 3rd-party or customer public key certificate should be installed in /etc/certs/ to allow verification by elfsign. For currently-released versions of Solaris, only cryptographic framework plugin libraries are verified by Solaris. However, all ELF files may be verified by the elfsign command at any time. Elfsign Algorithms Elfsign signatures are created by taking a digest of the ELF section contents, then signing the digest with RSA. To verify, one takes a digest of ELF file and compares with the expected digest that's computed from the signature and RSA public key. Originally elfsign took a MD5 digest of a SHA-1 digest of the ELF file sections, then signed the resulting digest with RSA. In Solaris 11.1 then Solaris 11.1 SRU 7 (5/2013), the elfsign crypto algorithms available have been expanded to keep up with evolving cryptography. The following table shows the available elfsign algorithms: Elfsign Algorithm Solaris Release Comments elfsign sign -F rsa_md5_sha1   S10, S11.0, S11.1 Default for S10. Not recommended* elfsign sign -F rsa_sha1 S11.1 Default for S11.1. Not recommended elfsign sign -F rsa_sha256 S11.1 patch SRU7+   Recommended ___ *Most or all CAs do not accept MD5 CSRs and do not issue MD5 certs due to MD5 hash collision problems. RSA Key Length. I recommend using RSA-2048 key length with elfsign is RSA-2048 as the best balance between a long expected "life time", interoperability, and performance. RSA-2048 keys have an expected lifetime through 2030 (and probably beyond). For details, see Recommendation for Key Management: Part 1: General, NIST Publication SP 800-57 part 1 (rev. 3, 7/2012, PDF), tables 2 and 4 (pp. 64, 67). Step 1: create or obtain a key and cert The first step in using elfsign is to obtain a key and cert from a public Certificate Authority (CA), or create your own self-signed key and cert. I'll briefly explain both methods. Obtaining a Certificate from a CA To obtain a cert from a CA, such as Verisign, Thawte, or Go Daddy (to name a few random examples), you create a private key and a Certificate Signing Request (CSR) file and send it to the CA, following the instructions of the CA on their website. They send back a signed public key certificate. The public key cert, along with the private key you created is used by elfsign to sign an ELF file. The public key cert is distributed with the software and is used by elfsign to verify elfsign signatures in ELF files. You need to request a RSA "Class 3 public key certificate", which is used for servers and software signing. Elfsign uses RSA and we recommend RSA-2048 keys. The private key and CSR can be generated with openssl(1) or pktool(1) on Solaris. Here's a simple example that uses pktool to generate a private RSA_2048 key and a CSR for sending to a CA: $ pktool gencsr keystore=file format=pem outcsr=MYCSR.p10 \ subject="CN=canineswworks.com,OU=Canine SW object signing" \ outkey=MYPRIVATEKEY.key $ openssl rsa -noout -text -in MYPRIVATEKEY.key Private-Key: (2048 bit) modulus: 00:d2:ef:42:f2:0b:8c:96:9f:45:32:fc:fe:54:94: . . . [omitted for brevity] . . . c9:c7 publicExponent: 65537 (0x10001) privateExponent: 26:14:fc:49:26:bc:a3:14:ee:31:5e:6b:ac:69:83: . . . [omitted for brevity] . . . 81 prime1: 00:f6:b7:52:73:bc:26:57:26:c8:11:eb:6c:dc:cb: . . . [omitted for brevity] . . . bc:91:d0:40:d6:9d:ac:b5:69 prime2: 00:da:df:3f:56:b2:18:46:e1:89:5b:6c:f1:1a:41: . . . [omitted for brevity] . . . f3:b7:48:de:c3:d9:ce:af:af exponent1: 00:b9:a2:00:11:02:ed:9a:3f:9c:e4:16:ce:c7:67: . . . [omitted for brevity] . . . 55:50:25:70:d3:ca:b9:ab:99 exponent2: 00:c8:fc:f5:57:11:98:85:8e:9a:ea:1f:f2:8f:df: . . . [omitted for brevity] . . . 23:57:0e:4d:b2:a0:12:d2:f5 coefficient: 2f:60:21:cd:dc:52:76:67:1a:d8:75:3e:7f:b0:64: . . . [omitted for brevity] . . . 06:94:56:d8:9d:5c:8e:9b $ openssl req -noout -text -in MYCSR.p10 Certificate Request: Data: Version: 2 (0x2) Subject: OU=Canine SW object signing, CN=canineswworks.com Subject Public Key Info: Public Key Algorithm: rsaEncryption Public-Key: (2048 bit) Modulus: 00:d2:ef:42:f2:0b:8c:96:9f:45:32:fc:fe:54:94: . . . [omitted for brevity] . . . c9:c7 Exponent: 65537 (0x10001) Attributes: Signature Algorithm: sha1WithRSAEncryption b3:e8:30:5b:88:37:68:1c:26:6b:45:af:5e:de:ea:60:87:ea: . . . [omitted for brevity] . . . 06:f9:ed:b4 Secure storage of RSA private key. The private key needs to be protected if the key signing is used for production (as opposed to just testing). That is, protect the key to protect against unauthorized signatures by others. One method is to use a PIN-protected PKCS#11 keystore. The private key you generate should be stored in a secure manner, such as in a PKCS#11 keystore using pktool(1). Otherwise others can sign your signature. Other secure key storage mechanisms include a SCA-6000 crypto card, a USB thumb drive stored in a locked area, a dedicated server with restricted access, Oracle Key Manager (OKM), or some combination of these. I also recommend secure backup of the private key. Here's an example of generating a private key protected in the PKCS#11 keystore, and a CSR. $ pktool setpin # use if PIN not set yet Enter token passphrase: changeme Create new passphrase: Re-enter new passphrase: Passphrase changed. $ pktool gencsr keystore=pkcs11 label=MYPRIVATEKEY \ format=pem outcsr=MYCSR.p10 \ subject="CN=canineswworks.com,OU=Canine SW object signing" $ pktool list keystore=pkcs11 Enter PIN for Sun Software PKCS#11 softtoken: Found 1 asymmetric public keys. Key #1 - RSA public key: MYPRIVATEKEY Here's another example that uses openssl instead of pktool to generate a private key and CSR: $ openssl genrsa -out cert.key 2048 $ openssl req -new -key cert.key -out MYCSR.p10 Self-Signed Cert You can use openssl or pktool to create a private key and a self-signed public key certificate. A self-signed cert is useful for development, testing, and internal use. The private key created should be stored in a secure manner, as mentioned above. The following example creates a private key, MYSELFSIGNED.key, and a public key cert, MYSELFSIGNED.pem, using pktool and displays the contents with the openssl command. $ pktool gencert keystore=file format=pem serial=0xD06F00D lifetime=20-year \ keytype=rsa hash=sha256 outcert=MYSELFSIGNED.pem outkey=MYSELFSIGNED.key \ subject="O=Canine Software Works, OU=Self-signed CA, CN=canineswworks.com" $ pktool list keystore=file objtype=cert infile=MYSELFSIGNED.pem Found 1 certificates. 1. (X.509 certificate) Filename: MYSELFSIGNED.pem ID: c8:24:59:08:2b:ae:6e:5c:bc:26:bd:ef:0a:9c:54:de:dd:0f:60:46 Subject: O=Canine Software Works, OU=Self-signed CA, CN=canineswworks.com Issuer: O=Canine Software Works, OU=Self-signed CA, CN=canineswworks.com Not Before: Oct 17 23:18:00 2013 GMT Not After: Oct 12 23:18:00 2033 GMT Serial: 0xD06F00D0 Signature Algorithm: sha256WithRSAEncryption $ openssl x509 -noout -text -in MYSELFSIGNED.pem Certificate: Data: Version: 3 (0x2) Serial Number: 3496935632 (0xd06f00d0) Signature Algorithm: sha256WithRSAEncryption Issuer: O=Canine Software Works, OU=Self-signed CA, CN=canineswworks.com Validity Not Before: Oct 17 23:18:00 2013 GMT Not After : Oct 12 23:18:00 2033 GMT Subject: O=Canine Software Works, OU=Self-signed CA, CN=canineswworks.com Subject Public Key Info: Public Key Algorithm: rsaEncryption Public-Key: (2048 bit) Modulus: 00:bb:e8:11:21:d9:4b:88:53:8b:6c:5a:7a:38:8b: . . . [omitted for brevity] . . . bf:77 Exponent: 65537 (0x10001) Signature Algorithm: sha256WithRSAEncryption 9e:39:fe:c8:44:5c:87:2c:8f:f4:24:f6:0c:9a:2f:64:84:d1: . . . [omitted for brevity] . . . 5f:78:8e:e8 $ openssl rsa -noout -text -in MYSELFSIGNED.key Private-Key: (2048 bit) modulus: 00:bb:e8:11:21:d9:4b:88:53:8b:6c:5a:7a:38:8b: . . . [omitted for brevity] . . . bf:77 publicExponent: 65537 (0x10001) privateExponent: 0a:06:0f:23:e7:1b:88:62:2c:85:d3:2d:c1:e6:6e: . . . [omitted for brevity] . . . 9c:e1:e0:0a:52:77:29:4a:75:aa:02:d8:af:53:24: c1 prime1: 00:ea:12:02:bb:5a:0f:5a:d8:a9:95:b2:ba:30:15: . . . [omitted for brevity] . . . 5b:ca:9c:7c:19:48:77:1e:5d prime2: 00:cd:82:da:84:71:1d:18:52:cb:c6:4d:74:14:be: . . . [omitted for brevity] . . . 5f:db:d5:5e:47:89:a7:ef:e3 exponent1: 32:37:62:f6:a6:bf:9c:91:d6:f0:12:c3:f7:04:e9: . . . [omitted for brevity] . . . 97:3e:33:31:89:66:64:d1 exponent2: 00:88:a2:e8:90:47:f8:75:34:8f:41:50:3b:ce:93: . . . [omitted for brevity] . . . ff:74:d4:be:f3:47:45:bd:cb coefficient: 4d:7c:09:4c:34:73:c4:26:f0:58:f5:e1:45:3c:af: . . . [omitted for brevity] . . . af:01:5f:af:ad:6a:09:bf Step 2: Sign the ELF File object By now you should have your private key, and obtained, by hook or crook, a cert (either from a CA or use one you created (a self-signed cert). The next step is to sign one or more objects with your private key and cert. Here's a simple example that creates an object file, signs, verifies, and lists the contents of the ELF signature. $ echo '#include <stdio.h>\nint main(){printf("Hello\\n");}'>hello.c $ make hello cc -o hello hello.c $ elfsign verify -v -c MYSELFSIGNED.pem -e hello elfsign: no signature found in hello. $ elfsign sign -F rsa_sha256 -v -k MYSELFSIGNED.key -c MYSELFSIGNED.pem -e hello elfsign: hello signed successfully. format: rsa_sha256. signer: O=Canine Software Works, OU=Self-signed CA, CN=canineswworks.com. signed on: October 17, 2013 04:22:49 PM PDT. $ elfsign list -f format -e hello rsa_sha256 $ elfsign list -f signer -e hello O=Canine Software Works, OU=Self-signed CA, CN=canineswworks.com $ elfsign list -f time -e hello October 17, 2013 04:22:49 PM PDT $ elfsign verify -v -c MYSELFSIGNED.key -e hello elfsign: verification of hello failed. format: rsa_sha256. signer: O=Canine Software Works, OU=Self-signed CA, CN=canineswworks.com. signed on: October 17, 2013 04:22:49 PM PDT. Signing using the pkcs11 keystore To sign the ELF file using a private key in the secure pkcs11 keystore, replace "-K MYSELFSIGNED.key" in the "elfsign sign" command line with "-T MYPRIVATEKEY", where MYPRIVATKEY is the pkcs11 token label. Step 3: Install the cert and test on another system Just signing the object isn't enough. You need to copy or install the cert and the signed ELF file(s) on another system to test that the signature is OK. Your public key cert should be installed in /etc/certs. Use elfsign verify to verify the signature. Elfsign verify checks each cert in /etc/certs until it finds one that matches the elfsign signature in the file. If one isn't found, the verification fails. Here's an example: $ su Password: # rm /etc/certs/MYSELFSIGNED.key # cp MYSELFSIGNED.pem /etc/certs # exit $ elfsign verify -v hello elfsign: verification of hello passed. format: rsa_sha256. signer: O=Canine Software Works, OU=Self-signed CA, CN=canineswworks.com. signed on: October 17, 2013 04:24:20 PM PDT. After testing, package your cert along with your ELF object to allow elfsign verification after your cert and object are installed or copied. Under the Hood: elfsign verification Here's the steps taken to verify a ELF file signed with elfsign. The steps to sign the file are similar except the private key exponent is used instead of the public key exponent and the .SUNW_signature section is written to the ELF file instead of being read from the file. Generate a digest (SHA-256) of the ELF file sections. This digest uses all ELF sections loaded in memory, but excludes the ELF header, the .SUNW_signature section, and the symbol table Extract the RSA signature (RSA-2048) from the .SUNW_signature section Extract the RSA public key modulus and public key exponent (65537) from the public key cert Calculate the expected digest as follows:     signaturepublicKeyExponent % publicKeyModulus Strip the PKCS#1 padding (most significant bytes) from the above. The padding is 0x00, 0x01, 0xff, 0xff, . . ., 0xff, 0x00. If the actual digest == expected digest, the ELF file is verified (OK). Further Information elfsign(1), pktool(1), and openssl(1) man pages. "Signed Solaris 10 Binaries?" blog by Darren Moffat (2005) shows how to use elfsign. "Simple CLI based CA on Solaris" blog by Darren Moffat (2008) shows how to set up a simple CA for use with self-signed certificates. "How to Create a Certificate by Using the pktool gencert Command" System Administration Guide: Security Services (available at docs.oracle.com)

  Read the article

• ASP.NET Controls – CommunityServer Captcha ControlAdapter, a practical case

  - by nmgomes

  The ControlAdapter is available since .NET framework version 2.0 and his main goal is to adapt and customize a control render in order to achieve a specific behavior or layout. This customization is done without changing the base control. A ControlAdapter is commonly used to custom render for specific platforms like Mobile. In this particular case the ControlAdapter was used to add a specific behavior to a Control. In this  post I will use one adapter to add a Captcha to all WeblogPostCommentForm controls within pontonetpt.com CommunityServer instance. The Challenge The ControlAdapter complexity is usually associated with the complexity/structure of is base control. This case is precisely one of those since base control dynamically load his content (controls) thru several ITemplate. Those of you who already played with ITemplate knows that while it is an excellent option for control composition it also brings to the table a big issue: “Controls defined within a template are not available for manipulation until they are instantiated inside another control.” While analyzing the WeblogPostCommentForm control I found that he uses the ITemplate technique to compose it’s layout and unfortunately I also found that the template content vary from theme to theme. This could have been a problem but luckily WeblogPostCommentForm control template content always contains a submit button with a well known ID (at least I can assume that there are a well known set of IDs). Using this submit button as anchor it’s possible to add the Captcha controls in the correct place. Another important finding was that WeblogPostCommentForm control inherits from the WrappedFormBase control which is the base control for all CommunityServer input forms. Knowing this inheritance link the main goal has changed to became the creation of a base ControlAdapter that  could be extended and customized to allow adding Captcha to: post comments form contact form user creation form. And, with this mind set, I decided to used the following ControlAdapter base class signature :public abstract class WrappedFormBaseCaptchaAdapter<T> : ControlAdapter where T : WrappedFormBase { }Great, but there are still many to do … Captcha The Captcha will be assembled with: A dynamically generated image with a set of random numbers A TextBox control where the image number will be inserted A Validator control to validate whether TextBox numbers match the image numbers This is a common Captcha implementation, is not rocket science and don’t bring any additional problem. The main problem, as told before, is to find the correct anchor control to ensure a correct Captcha control injection. The anchor control can vary by: target control  theme Implementation To support this dynamic scenario I choose to use the following implementation:private List<string> _validAnchorIds = null; protected virtual List<string> ValidAnchorIds { get { if (this._validAnchorIds == null) { this._validAnchorIds = new List<string>(); this._validAnchorIds.Add("btnSubmit"); } return this._validAnchorIds; } } private Control GetAnchorControl(T wrapper) { if (this.ValidAnchorIds == null || this.ValidAnchorIds.Count == 0) { throw new ArgumentException("Cannot be null or empty", "validAnchorNames"); } var q = from anchorId in this.ValidAnchorIds let anchorControl = CSControlUtility.Instance().FindControl(wrapper, anchorId) where anchorControl != null select anchorControl; return q.FirstOrDefault(); } I can now, using the ValidAnchorIds property, configure a set of valid anchor control  Ids. The GetAnchorControl method searches for a valid anchor control within the set of valid control Ids. Here, some of you may question why to use a LINQ To Objects expression, but the important here is to notice the usage of CSControlUtility.Instance().FindControl CommunityServer method. I want to build on top of CommunityServer not to reinvent the wheel. Assuming that an anchor control was found, it’s now possible to inject the Captcha at the correct place. This not something new, we do this all the time when creating server controls or adding dynamic controls:protected sealed override void CreateChildControls() { base.CreateChildControls(); if (this.IsCaptchaRequired) { T wrapper = base.Control as T; if (wrapper != null) { Control anchorControl = GetAnchorControl(wrapper); if (anchorControl != null) { Panel phCaptcha = new Panel {CssClass = "CommonFormField", ID = "Captcha"}; int index = anchorControl.Parent.Controls.IndexOf(anchorControl); anchorControl.Parent.Controls.AddAt(index, phCaptcha); CaptchaConfiguration.DefaultProvider.AddCaptchaControls( phCaptcha, GetValidationGroup(wrapper, anchorControl)); } } } } Here you can see a new entity in action: a provider. This is a CaptchaProvider class instance and is only goal is to create the Captcha itself and do everything else is needed to ensure is correct operation.public abstract class CaptchaProvider : ProviderBase { public abstract void AddCaptchaControls(Panel captchaPanel, string validationGroup); } You can create your own specific CaptchaProvider class to use different Captcha strategies including the use of existing Captcha services  like ReCaptcha. Once the generic ControlAdapter was created became extremely easy to created a specific one. Here is the specific ControlAdapter for the WeblogPostCommentForm control:public class WeblogPostCommentFormCaptchaAdapter : WrappedFormBaseCaptchaAdapter<WrappedFormBase> { #region Overriden Methods protected override List<string> ValidAnchorIds { get { List<string> validAnchorNames = base.ValidAnchorIds; validAnchorNames.Add("CommentSubmit"); return validAnchorNames; } } protected override string DefaultValidationGroup { get { return "CreateCommentForm"; } } #endregion Overriden Methods } Configuration This is the magic step. Without changing the original pages and keeping the application original assemblies untouched we are going to add a new behavior to the CommunityServer application. To glue everything together you must follow this steps: Add the following configuration to default.browser file:<?xml version='1.0' encoding='utf-8'?> <browsers> <browser refID="Default"> <controlAdapters> <!-- Adapter for the WeblogPostCommentForm control in order to add the Captcha and prevent SPAM comments --> <adapter controlType="CommunityServer.Blogs.Controls.WeblogPostCommentForm" adapterType="NunoGomes.CommunityServer.Components.WeblogPostCommentFormCaptchaAdapter, NunoGomes.CommunityServer" /> </controlAdapters> </browser> </browsers> Add the following configuration to web.config file:<configuration> <configSections> <!-- New section for Captcha providers configuration --> <section name="communityServer.Captcha" type="NunoGomes.CommunityServer.Captcha.Configuration.CaptchaSection" /> </configSections> <!-- Configuring a simple Captcha provider --> <communityServer.Captcha defaultProvider="simpleCaptcha"> <providers> <add name="simpleCaptcha" type="NunoGomes.CommunityServer.Captcha.Providers.SimpleCaptchaProvider, NunoGomes.CommunityServer" imageUrl="~/captcha.ashx" enabled="true" passPhrase="_YourPassPhrase_" saltValue="_YourSaltValue_" hashAlgorithm="SHA1" passwordIterations="3" keySize="256" initVector="_YourInitVectorWithExactly_16_Bytes_" /> </providers> </communityServer.Captcha> <system.web> <httpHandlers> <!-- The Captcha Image handler used by the simple Captcha provider --> <add verb="GET" path="captcha.ashx" type="NunoGomes.CommunityServer.Captcha.Providers.SimpleCaptchaProviderImageHandler, NunoGomes.CommunityServer" /> </httpHandlers> </system.web> <system.webServer> <handlers accessPolicy="Read, Write, Script, Execute"> <!-- The Captcha Image handler used by the simple Captcha provider --> <add verb="GET" name="captcha" path="captcha.ashx" type="NunoGomes.CommunityServer.Captcha.Providers.SimpleCaptchaProviderImageHandler, NunoGomes.CommunityServer" /> </handlers> </system.webServer> </configuration> Conclusion Building a ControlAdapter can be complex but the reward is his ability to allows us, thru configuration changes, to modify an application render and/or behavior. You can see this ControlAdapter in action here and here (anonymous required). A complete solution is available in “CommunityServer Extensions” Codeplex project.

  Read the article

• Randomly displayed flashing lines, no response to all shortcuts, just power off. [syslog included]

  - by B. Roland

  Hello! I have an old machine, and I want to use for that to learn employees how to use Ubuntu, and to be easyer to switch from Windows. I've been installed 10.04, and updated, but this strange stuff is happend. Graphical installion failed, same strange thing. With alternate workd. Sometimes, when I boot up, a boot message displayed: Keyboard failure..., often diplayed after reboot, and after shutdown, when I haven't plugged off from AC. I replaced the keyboard yet, same failure... If I powered off, and plugged off from AC, no keyboard problems displayed in boot time. Details Configuration: Dell OptiPlex GX60 - in original cover, no changes. 256 MB DDR 166 MHz Intel® Celeron® Processor 2.40 GHz Dell 0C3207 Base Board I know, that is not enough, but I have three other Nec compuers, with nearly similar config, and they works well with 9.10, 10.04, 10.10. Live CDs I've been tried with 10.04 and 10.10, but the problem is displayed too. With 9.10 no strange things displayed, but it froze, during a simple apt-get install. Syslog An error loop is logged here, but I paste the whole startup and error lines. The flashing lines are displayed sometimes immediately after login, but sometimes after 10 minutes, but once occured, that nothing happend. Strange thing is displayed immediately after login: here. An other boot, after some minutes, strange lines, and loop in log appeard: here. The loop should be that: Jan 23 00:20:08 machine_name kernel: [ 46.782212] [drm:i915_gem_entervt_ioctl] *ERROR* Reenabling wedged hardware, good luck Jan 23 00:20:08 machine_name kernel: [ 47.100033] [drm:i915_hangcheck_elapsed] *ERROR* Hangcheck timer elapsed... GPU hung Jan 23 00:20:08 machine_name kernel: [ 47.100045] render error detected, EIR: 0x00000000 Jan 23 00:20:08 machine_name kernel: [ 47.101487] [drm:i915_do_wait_request] *ERROR* i915_do_wait_request returns -5 (awaiting 16 at 9) Jan 23 00:20:11 machine_name kernel: [ 49.152020] [drm:i915_gem_idle] *ERROR* hardware wedged Jan 23 00:20:11 machine_name gdm-simple-slave[1245]: WARNING: Unable to load file '/etc/gdm/custom.conf': No such file or directory Jan 23 00:20:11 machine_name acpid: client 1239[0:0] has disconnected Jan 23 00:20:11 machine_name acpid: client connected from 1247[0:0] Jan 23 00:20:11 machine_name acpid: 1 client rule loaded UPDATE Added syslog things: before errors, error loop, the complete shutdown(after the big updates): Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Sucessfully called chroot. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Sucessfully dropped privileges. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Sucessfully limited resources. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Running. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Watchdog thread running. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Canary thread running. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Sucessfully made thread 1337 of process 1337 (n/a) owned by '1001' high priority at nice level -11. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Supervising 1 threads of 1 processes of 1 users. Jan 28 20:40:32 machine_name rtkit-daemon[1339]: Sucessfully made thread 1345 of process 1337 (n/a) owned by '1001' RT at priority 5. Jan 28 20:40:32 machine_name rtkit-daemon[1339]: Supervising 2 threads of 1 processes of 1 users. Jan 28 20:40:32 machine_name rtkit-daemon[1339]: Sucessfully made thread 1349 of process 1337 (n/a) owned by '1001' RT at priority 5. Jan 28 20:40:32 machine_name rtkit-daemon[1339]: Supervising 3 threads of 1 processes of 1 users. Jan 28 20:40:37 machine_name pulseaudio[1337]: ratelimit.c: 2 events suppressed Jan 28 20:41:33 machine_name AptDaemon: INFO: Initializing daemon Jan 28 20:41:44 machine_name kernel: [ 167.691563] lo: Disabled Privacy Extensions Jan 28 20:47:33 machine_name AptDaemon: INFO: Quiting due to inactivity Jan 28 20:47:33 machine_name AptDaemon: INFO: Shutdown was requested Jan 28 20:59:50 machine_name kernel: [ 1253.840513] lo: Disabled Privacy Extensions Jan 28 21:17:02 machine_name CRON[1874]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Jan 28 21:17:38 machine_name kernel: [ 2321.553239] lo: Disabled Privacy Extensions Jan 28 22:07:44 machine_name kernel: [ 5327.840254] lo: Disabled Privacy Extensions Jan 28 22:17:02 machine_name CRON[2665]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Jan 28 22:32:38 machine_name sudo: pam_sm_authenticate: Called Jan 28 22:32:38 machine_name sudo: pam_sm_authenticate: username = [some_user] Jan 28 22:32:38 machine_name sudo: pam_sm_authenticate: /home/some_user is already mounted Jan 28 22:57:03 machine_name kernel: [ 8286.641472] lo: Disabled Privacy Extensions Jan 28 22:57:24 machine_name sudo: pam_sm_authenticate: Called Jan 28 22:57:24 machine_name sudo: pam_sm_authenticate: username = [some_user] Jan 28 22:57:24 machine_name sudo: pam_sm_authenticate: /home/some_user is already mounted Jan 28 23:07:42 machine_name kernel: [ 8925.272030] [drm:i915_hangcheck_elapsed] *ERROR* Hangcheck timer elapsed... GPU hung Jan 28 23:07:42 machine_name kernel: [ 8925.272048] render error detected, EIR: 0x00000000 Jan 28 23:07:42 machine_name kernel: [ 8925.272093] [drm:i915_do_wait_request] *ERROR* i915_do_wait_request returns -5 (awaiting 171453 at 171452) Jan 28 23:07:45 machine_name kernel: [ 8928.868041] [drm:i915_gem_idle] *ERROR* hardware wedged Jan 28 23:08:10 machine_name acpid: client 925[0:0] has disconnected Jan 28 23:08:10 machine_name acpid: client connected from 8127[0:0] Jan 28 23:08:10 machine_name acpid: 1 client rule loaded Jan 28 23:08:11 machine_name kernel: [ 8955.046248] [drm:i915_gem_entervt_ioctl] *ERROR* Reenabling wedged hardware, good luck Jan 28 23:08:12 machine_name kernel: [ 8955.364016] [drm:i915_hangcheck_elapsed] *ERROR* Hangcheck timer elapsed... GPU hung Jan 28 23:08:12 machine_name kernel: [ 8955.364027] render error detected, EIR: 0x00000000 Jan 28 23:08:12 machine_name kernel: [ 8955.364407] [drm:i915_do_wait_request] *ERROR* i915_do_wait_request returns -5 (awaiting 171457 at 171452) Jan 28 23:08:14 machine_name kernel: [ 8957.472025] [drm:i915_gem_idle] *ERROR* hardware wedged Jan 28 23:08:14 machine_name acpid: client 8127[0:0] has disconnected Jan 28 23:08:14 machine_name acpid: client connected from 8141[0:0] Jan 28 23:08:14 machine_name acpid: 1 client rule loaded Jan 28 23:08:15 machine_name kernel: [ 8958.671722] [drm:i915_gem_entervt_ioctl] *ERROR* Reenabling wedged hardware, good luck Jan 28 23:08:15 machine_name kernel: [ 8958.988015] [drm:i915_hangcheck_elapsed] *ERROR* Hangcheck timer elapsed... GPU hung Jan 28 23:08:15 machine_name kernel: [ 8958.988026] render error detected, EIR: 0x00000000 Jan 28 23:08:15 machine_name kernel: [ 8958.989400] [drm:i915_do_wait_request] *ERROR* i915_do_wait_request returns -5 (awaiting 171459 at 171452) Jan 28 23:08:16 machine_name init: tty4 main process (848) killed by TERM signal Jan 28 23:08:16 machine_name init: tty5 main process (856) killed by TERM signal Jan 28 23:08:16 machine_name NetworkManager: nm_signal_handler(): Caught signal 15, shutting down normally. Jan 28 23:08:16 machine_name init: tty2 main process (874) killed by TERM signal Jan 28 23:08:16 machine_name init: tty3 main process (875) killed by TERM signal Jan 28 23:08:16 machine_name init: tty6 main process (877) killed by TERM signal Jan 28 23:08:16 machine_name init: cron main process (890) killed by TERM signal Jan 28 23:08:16 machine_name init: tty1 main process (1146) killed by TERM signal Jan 28 23:08:16 machine_name avahi-daemon[644]: Got SIGTERM, quitting. Jan 28 23:08:16 machine_name avahi-daemon[644]: Leaving mDNS multicast group on interface eth0.IPv4 with address 10.238.11.134. Jan 28 23:08:16 machine_name acpid: exiting Jan 28 23:08:16 machine_name init: avahi-daemon main process (644) terminated with status 255 Jan 28 23:08:17 machine_name kernel: Kernel logging (proc) stopped. Jan 28 23:09:00 machine_name kernel: imklog 4.2.0, log source = /proc/kmsg started. Jan 28 23:09:00 machine_name rsyslogd: [origin software="rsyslogd" swVersion="4.2.0" x-pid="516" x-info="http://www.rsyslog.com"] (re)start Jan 28 23:09:00 machine_name rsyslogd: rsyslogd's groupid changed to 103 Jan 28 23:09:00 machine_name rsyslogd: rsyslogd's userid changed to 101 Jan 28 23:09:00 machine_name rsyslogd-2039: Could no open output file '/dev/xconsole' [try http://www.rsyslog.com/e/2039 ] When I hit the On/Off button, the system shuts down normally. May be it a hardware problem, but I don't know... Can you say something useful to solve my problem?

  Read the article

• Running TeamCity from Amazon EC2 - Cloud based scalable build and continuous Integration

  - by RoyOsherove

  I’ve been having fun playing with the amazon EC2 cloud service. I set up a server running TeamCity, and an image of a server that just runs a TeamCity agent. I also setup TeamCity  to automatically instantiate agents on EC2 and shut them down based upon availability of free agents. Here’s how I did it: The first step was setting up the teamcity server. Create an account on amazon EC2 (BTW, amazon’s sites works better in IE than it does in chrome.. who knew!?) Open the EC2 dashboard, and click “Launch Instance” . From the “Quick Start” tab I selected from the list: “Getting Started on Microsoft Windows Server 2008 (AMI Id: ami-c5e40dac)” .  it’s good enough to just run teamcity. In the instance details, I used the default (Small instance, 1.7 GB mem). You might want to choose a close availability zone based on where you are. We want to “Launch instances” so click continue. Select the default kernel, RAM disk and all. No need to enable monitoring for now (you can do that later). click continue. If you don’t have a key pair, you will be prompted to create one. Once you do, select it in the list. Now you’ll be prompted to create a security group. I named mine “TC” as in “TeamCity”. each group is a bunch of settings on which ports can be let through into and out of a hosted machine.  keep it as the default settings. We will change them later. Click continue,  review and then click “Launch”. Now you’ll be able to see the new instance in the running instances list on your site. Now, you need to install stuff on that instance (TeamCity!) . To do that, you’ll need to Remote desktop into that instance. To do that, we’ll get the admin password for that instance: Check it on the list, and click “Instance Actions” - “Get Windows Admin Password”. You might have to wait about 10 minutes or so for the password to be generated for you. Once you have the password, you will remote desktop (start-run-‘mstsc’) into the instance. It’s address is a dns address shown below the list under “Public DNS”. it looks something like: ec2-256-226-194-91.compute-1.amazonaws.com Once you’re inside the instance – you’ll need to open IE (it is in hardened mode so you’ll have to relax its security settings to download stuff). I first downloaded chrome and using chrome I downloaded TeamCity. Note that the download speed is FAST. several MBs per second. To be able to see TeamCity from the outside, you will need to open the advanced firewall settings inside the remote machine, and add incoming and outgoing rules for port 80 (HTTP). Once you do that, you should be able to see the machine from the outside. If you still can’t, see the next step. I also enabled ports 9090 since I will use this machine to create an agent image later as well. Now configure the security group (TC) to enable talking to agents: IN the EC2 dashboard click on “Security Groups” and select your group. To add a rule, click on the empty list under the ‘protocol’ header. select TCP. from and ‘to’ ports are 9090. source ip is 0.0.0.0/0 (every ip is allowed). click “Save.  Also make sure you can see “HTTP” tcp 80 in that list. if you can’t see it, add it or you won’t be able to browse to the machine’s teamcity server home page. I also set an elastic IP for the machine: so I always have the same IP for the machine instance. Allocate and set one through the”Elastic IP” link on the EC2 dashboard.   you should now have a working instance of teamcity.   Now let’s create an agent image. Repeat steps 1-9, but this time, make sure you select a machine that fits what an agent might do. I selected Instance type – Hihg-CPU medium machine,  that is much faster. On that machine, I installed what I needed (VS 2010, PostSharp etc..). downloading VS 2010 from MSDN (2 GB took less than 10 min!) Now, instead of installing teamcity, browse using the browser to the teamcity homepage (from within the remote machine). go to the Administration page, and click the upper right link “Install agents”. Install the agent on he local machine – set it to the IP or DNS of the running TeamCity server. That way you’ll be able to check their connectivity live before making this machine your official agent image to reuse. Once the agent is installed, see that the TC server can see it and use it. see steps 13-14 above if they can’t. Once it works, you can take steps to make this image your agent image to be reused. next, here is a copy-paste of several steps to take from http://confluence.jetbrains.net/display/TCD5/Setting+Up+TeamCity+for+Amazon+EC2 Configure system so that agent it is started on machine boot (and make sure TeamCity server is accessible on machine boot). Test the setup by rebooting machine and checking that the agent connects normally to the server. Prepare the Image for bundling: Remove any temporary/history information in the system. Stop the agent (under Windows stop the service but leave it in Automatic startup type) Delete content agent logs and temp directories (not necessary) Delete "<Agent Home>/conf/amazon-*" file (not necessary) Change config/buildAgent.properties to remove properties: name, serverAddress, authToken (not necessary)   Now, we need to: Make AMI from the running instance. Configure TeamCity EC2 support on TeamCity server. Making an AMI: Check the instance of the agent in the EC2 dashboard instance list, and select instance actions->Create Image (EBS AMI) you’ll see the image pending in the APIs list in the EC2 dashboard. this could take 30 minutes or more. meanwhile we can configure the could support in the teamcity server. COPY THE AMI ID to the clipboard (looks like ami-a88aa4ce) Configuring TeamCity for Cloud: In TeamCity, click on “Agents” and then on “Cloud” tab. this is where you will control your cloud agents. to configure new cloud agents based on APIs, click on the right link to the “configuration page” Create a new profile and select AMazon EC2 as cloud type. Use your AMI ID that you copied to the clipboard into the “Images” field. Select an availability zone that is the same as the one your instance is running on for best communication perf between them make sure you select the ‘TC’ security group hopefully, that should be it, and teamcity will try to instantiate new instances on demand. Note that it may take around 10 minutes for an agent to become available to teamcity from the time it’s started.

  Read the article

• Thread placement policies on NUMA systems - update

  - by Dave

  In a prior blog entry I noted that Solaris used a "maximum dispersal" placement policy to assign nascent threads to their initial processors. The general idea is that threads should be placed as far away from each other as possible in the resource topology in order to reduce resource contention between concurrently running threads. This policy assumes that resource contention -- pipelines, memory channel contention, destructive interference in the shared caches, etc -- will likely outweigh (a) any potential communication benefits we might achieve by packing our threads more densely onto a subset of the NUMA nodes, and (b) benefits of NUMA affinity between memory allocated by one thread and accessed by other threads. We want our threads spread widely over the system and not packed together. Conceptually, when placing a new thread, the kernel picks the least loaded node NUMA node (the node with lowest aggregate load average), and then the least loaded core on that node, etc. Furthermore, the kernel places threads onto resources -- sockets, cores, pipelines, etc -- without regard to the thread's process membership. That is, initial placement is process-agnostic. Keep reading, though. This description is incorrect. On Solaris 10 on a SPARC T5440 with 4 x T2+ NUMA nodes, if the system is otherwise unloaded and we launch a process that creates 20 compute-bound concurrent threads, then typically we'll see a perfect balance with 5 threads on each node. We see similar behavior on an 8-node x86 x4800 system, where each node has 8 cores and each core is 2-way hyperthreaded. So far so good; this behavior seems in agreement with the policy I described in the 1st paragraph. I recently tried the same experiment on a 4-node T4-4 running Solaris 11. Both the T5440 and T4-4 are 4-node systems that expose 256 logical thread contexts. To my surprise, all 20 threads were placed onto just one NUMA node while the other 3 nodes remained completely idle. I checked the usual suspects such as processor sets inadvertently left around by colleagues, processors left offline, and power management policies, but the system was configured normally. I then launched multiple concurrent instances of the process, and, interestingly, all the threads from the 1st process landed on one node, all the threads from the 2nd process landed on another node, and so on. This happened even if I interleaved thread creating between the processes, so I was relatively sure the effect didn't related to thread creation time, but rather that placement was a function of process membership. I this point I consulted the Solaris sources and talked with folks in the Solaris group. The new Solaris 11 behavior is intentional. The kernel is no longer using a simple maximum dispersal policy, and thread placement is process membership-aware. Now, even if other nodes are completely unloaded, the kernel will still try to pack new threads onto the home lgroup (socket) of the primordial thread until the load average of that node reaches 50%, after which it will pick the next least loaded node as the process's new favorite node for placement. On the T4-4 we have 64 logical thread contexts (strands) per socket (lgroup), so if we launch 48 concurrent threads we will find 32 placed on one node and 16 on some other node. If we launch 64 threads we'll find 32 and 32. That means we can end up with our threads clustered on a small subset of the nodes in a way that's quite different that what we've seen on Solaris 10. So we have a policy that allows process-aware packing but reverts to spreading threads onto other nodes if a node becomes too saturated. It turns out this policy was enabled in Solaris 10, but certain bugs suppressed the mixed packing/spreading behavior. There are configuration variables in /etc/system that allow us to dial the affinity between nascent threads and their primordial thread up and down: see lgrp_expand_proc_thresh, specifically. In the OpenSolaris source code the key routine is mpo_update_tunables(). This method reads the /etc/system variables and sets up some global variables that will subsequently be used by the dispatcher, which calls lgrp_choose() in lgrp.c to place nascent threads. Lgrp_expand_proc_thresh controls how loaded an lgroup must be before we'll consider homing a process's threads to another lgroup. Tune this value lower to have it spread your process's threads out more. To recap, the 'new' policy is as follows. Threads from the same process are packed onto a subset of the strands of a socket (50% for T-series). Once that socket reaches the 50% threshold the kernel then picks another preferred socket for that process. Threads from unrelated processes are spread across sockets. More precisely, different processes may have different preferred sockets (lgroups). Beware that I've simplified and elided details for the purposes of explication. The truth is in the code. Remarks: It's worth noting that initial thread placement is just that. If there's a gross imbalance between the load on different nodes then the kernel will migrate threads to achieve a better and more even distribution over the set of available nodes. Once a thread runs and gains some affinity for a node, however, it becomes "stickier" under the assumption that the thread has residual cache residency on that node, and that memory allocated by that thread resides on that node given the default "first-touch" page-level NUMA allocation policy. Exactly how the various policies interact and which have precedence under what circumstances could the topic of a future blog entry. The scheduler is work-conserving. The x4800 mentioned above is an interesting system. Each of the 8 sockets houses an Intel 7500-series processor. Each processor has 3 coherent QPI links and the system is arranged as a glueless 8-socket twisted ladder "mobius" topology. Nodes are either 1 or 2 hops distant over the QPI links. As an aside the mapping of logical CPUIDs to physical resources is rather interesting on Solaris/x4800. On SPARC/Solaris the CPUID layout is strictly geographic, with the highest order bits identifying the socket, the next lower bits identifying the core within that socket, following by the pipeline (if present) and finally the logical thread context ("strand") on the core. But on Solaris on the x4800 the CPUID layout is as follows. [6:6] identifies the hyperthread on a core; bits [5:3] identify the socket, or package in Intel terminology; bits [2:0] identify the core within a socket. Such low-level details should be of interest only if you're binding threads -- a bad idea, the kernel typically handles placement best -- or if you're writing NUMA-aware code that's aware of the ambient placement and makes decisions accordingly. Solaris introduced the so-called critical-threads mechanism, which is expressed by putting a thread into the FX scheduling class at priority 60. The critical-threads mechanism applies to placement on cores, not on sockets, however. That is, it's an intra-socket policy, not an inter-socket policy. Solaris 11 introduces the Power Aware Dispatcher (PAD) which packs threads instead of spreading them out in an attempt to be able to keep sockets or cores at lower power levels. Maximum dispersal may be good for performance but is anathema to power management. PAD is off by default, but power management polices constitute yet another confounding factor with respect to scheduling and dispatching. If your threads communicate heavily -- one thread reads cache lines last written by some other thread -- then the new dense packing policy may improve performance by reducing traffic on the coherent interconnect. On the other hand if your threads in your process communicate rarely, then it's possible the new packing policy might result on contention on shared computing resources. Unfortunately there's no simple litmus test that says whether packing or spreading is optimal in a given situation. The answer varies by system load, application, number of threads, and platform hardware characteristics. Currently we don't have the necessary tools and sensoria to decide at runtime, so we're reduced to an empirical approach where we run trials and try to decide on a placement policy. The situation is quite frustrating. Relatedly, it's often hard to determine just the right level of concurrency to optimize throughput. (Understanding constructive vs destructive interference in the shared caches would be a good start. We could augment the lines with a small tag field indicating which strand last installed or accessed a line. Given that, we could augment the CPU with performance counters for misses where a thread evicts a line it installed vs misses where a thread displaces a line installed by some other thread.)

  Read the article

• No root file system is defined error after installation

  - by LearnCode

  I installed ubuntu through Wubi and once i rebooted I get no root file system defined error. here's the output of the boot_info_script.Could anyone point me out where the error is. Boot Info Script 0.60 from 17 May 2011 ============================= Boot Info Summary: =============================== => Windows is installed in the MBR of /dev/sda. => Windows is installed in the MBR of /dev/sdb. sda1: __________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Windows 7 Boot files: /bootmgr /Boot/BCD /Windows/System32/winload.exe /ntldr /ntdetect.com /wubildr /ubuntu/winboot/wubildr /wubildr.mbr /ubuntu/winboot/wubildr.mbr /ubuntu/disks/root.disk /ubuntu/disks/swap.disk sda1/Wubi: _____________________________________________________________________ File system: Boot sector type: Unknown Boot sector info: Mounting failed: mount: unknown filesystem type '' sda2: __________________________________________________________________________ File system: vfat Boot sector type: Unknown Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files: /boot.ini /ntldr /NTDETECT.COM sdb1: __________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files: ============================ Drive/Partition Info: ============================= Drive: sda _____________________________________________________________________ Disk /dev/sda: 160.0 GB, 160041885696 bytes 240 heads, 63 sectors/track, 20673 cylinders, total 312581808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start Sector End Sector # of Sectors Id System /dev/sda1 * 63 301,250,879 301,250,817 7 NTFS / exFAT / HPFS /dev/sda2 301,250,943 312,575,759 11,324,817 c W95 FAT32 (LBA) GUID Partition Table detected, but does not seem to be used. Partition Start Sector End Sector # of Sectors System /dev/sda1 323,465,741,313,502,988275,962,973,585-323,465,465,350,529,402 - /dev/sda2 242,728,591,638,290,720578,721,383,108,845,578335,992,791,470,554,859 - /dev/sda3 1,827,498,311,425,204,2562,091,935,274,843,009,907264,436,963,417,805,652 - /dev/sda4 579,711,218,081,401,3572,006,665,459,744,645,1521,426,954,241,663,243,796 - /dev/sda11 270,286,346,402,038,1183,786,543,326,404,525,9543,516,256,980,002,487,837 - /dev/sda12 4,179,681,002,230,769,6684,179,389,374,010,033,387-291,628,220,736,280 - /dev/sda13 232,556,480,979,456,1311,160,152,593,793,119,235927,596,112,813,663,105 - /dev/sda14 98,342,784,050,266,9183,691,264,578,843,725,1953,592,921,794,793,458,278 - /dev/sda15 2,307,845,219,957,882,4961,850,841,032,955,276,350-457,004,187,002,606,145 - /dev/sda16 512,592,046,878,946,497368,458,231,024,779,444-144,133,815,854,167,052 - /dev/sda17 2,504,135,232,870,384,3923,665,087,872,719,320,8291,160,952,639,848,936,438 - /dev/sda18 3,783,181,605,270,691,304122,034,509,624,708,942-3,661,147,095,645,982,361 - /dev/sda19 3,519,661,520,275,829,5122,376,243,094,723,723,587-1,143,418,425,552,105,924 - /dev/sda20 3,867,920,076,859,0744,494,691,111,933,625,1044,490,823,191,856,766,031 - /dev/sda21 1,500,144,061,909,253,7612,511,182,033,846,676,3401,011,037,971,937,422,580 - /dev/sda22 13,035,625,499,900,0062,360,168,613,941,394,9472,347,132,988,441,494,942 - /dev/sda23 4,228,978,682,068,599,48813,159,423,631,648,263-4,215,819,258,436,951,224 - /dev/sda24 3,695,955,742,872,046,9084,561,928,726,501,845,776865,972,983,629,798,869 - /dev/sda25 1,297,460,286,683,948,0461,444,350,486,339,417,957146,890,199,655,469,912 - /dev/sda26 1,228,858,248,533,131,831 0-1,228,858,248,533,131,830 - /dev/sda121 3,189,184,846,146,487,1461,849,820,258,006,914,852-1,339,364,588,139,572,293 - /dev/sda122 1,226,215,547,991,800,578389,781,518,734,546,300-836,434,029,257,254,277 - /dev/sda123 3,851,660,168,574,583,4654,046,215,657,583,031,556194,555,489,008,448,092 - /dev/sda124 1,197,460,980,174,153,341699,103,965,005,093,246-498,357,015,169,060,094 - Drive: sdb _____________________________________________________________________ Disk /dev/sdb: 750.2 GB, 750153367552 bytes 255 heads, 63 sectors/track, 91200 cylinders, total 1465143296 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start Sector End Sector # of Sectors Id System /dev/sdb1 2,048 1,465,143,295 1,465,141,248 7 NTFS / exFAT / HPFS "blkid" output: ________________________________________________________________ Device UUID TYPE LABEL /dev/loop0 iso9660 Ubuntu 11.04 amd64 /dev/loop1 squashfs /dev/sda1 E814B55B14B52E06 ntfs /dev/sda2 01CD-023B vfat HP_RECOVERY /dev/sdb1 7836F22A36F1E8D0 ntfs Elements ================================ Mount points: ================================= Device Mount_Point Type Options /dev/loop0 /cdrom iso9660 (ro,noatime) /dev/loop1 /rofs squashfs (ro,noatime) /dev/sdb1 /mnt fuseblk (rw,nosuid,nodev,allow_other,blksize=4096) ================================ sda2/boot.ini: ================================ -------------------------------------------------------------------------------- [boot loader] timeout=0 default=C:\CMDCONS\BOOTSECT.DAT [operating systems] multi(0)disk(0)rdisk(0)partition(1)\WINDOWS="Microsoft Windows XP Professional" /fastdetect C:\CMDCONS\BOOTSECT.DAT="Microsoft Windows Recovery Console" /cmdcons -------------------------------------------------------------------------------- ======================== Unknown MBRs/Boot Sectors/etc: ======================== Unknown GPT Partiton Type c104043000e9b9040dff24b580010100 Unknown GPT Partiton Type 46313020746f20737461727420746865 Unknown GPT Partiton Type 65727920706172746974696f6e207761 Unknown GPT Partiton Type 727920706172746974696f6e0d0a0000 Unknown GPT Partiton Type 000f84e5f7668b162404e82804744066 Unknown GPT Partiton Type ce01e8dc038bfe66391624047505e8d9 Unknown GPT Partiton Type 0345086603f0e881030bd2740333d240 Unknown GPT Partiton Type bece01e8db0287fec645041266895508 Unknown GPT Partiton Type 01f60634010175078b363b01e854f5e8 Unknown GPT Partiton Type 313825740ffec03865107408fec03824 Unknown GPT Partiton Type 02f60634014074088bfdbece01e85101 Unknown GPT Partiton Type 263401f9e894f30f858ef4e8e201e8ec Unknown GPT Partiton Type f7e960f35245434f5645525966606633 Unknown GPT Partiton Type 660faf1e00106603dac3668b0e001066 Unknown GPT Partiton Type 8bfd386d04740583c710e2f6c36660c6 Unknown GPT Partiton Type 04ebf132c0b91000f3aac3bf0c04ebf3 Unknown GPT Partiton Type 02662bc1660fb71e0e02662bc366031e Unknown GPT Partiton Type f4b40ebb0700b901003c08751381ff25 Unknown GPT Partiton Type 534f465448494e4b90653f62011b0100 Unknown GPT Partiton Type 0b050900027777772e68702e636f6d00 Unknown GPT Partiton Type d441a0f5030003000ecb744a08bb3746 Unknown GPT Partiton Type f8579a116b4a7aa931cde97a4b9b5c09 Unknown GPT Partiton Type 7229990415b77c0a1970e7e824237a3a Unknown GPT Partiton Type afb6e34d6b4bd8c7c0eada19a9786cc3 Unknown BootLoader on sda1/Wubi 00000000 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 |0000000000000000| * 00000200 Unknown BootLoader on sda2 00000000 e9 a7 00 52 45 43 4f 56 45 52 59 00 02 08 20 00 |...RECOVERY... .| 00000010 02 00 00 00 00 f8 00 00 3f 00 f0 00 7f b9 f4 11 |........?.......| 00000020 8c cd ac 00 1e 2b 00 00 00 00 00 00 02 00 00 00 |.....+..........| 00000030 01 00 06 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| 00000040 80 00 29 3b 02 cd 01 20 20 20 20 20 20 20 20 20 |..);... | 00000050 20 20 46 41 54 33 32 20 20 20 8b d0 c1 e2 02 80 | FAT32 ......| 00000060 e6 01 66 c1 e8 07 66 3b 46 f8 74 2a 66 89 46 f8 |..f...f;F.t*f.F.| 00000070 66 03 46 f4 66 0f b6 5e 28 80 e3 0f 74 0f 3a 5e |f.F.f..^(...t.:^| 00000080 10 0f 83 90 00 66 0f af 5e 24 66 03 c3 bb e0 07 |.....f..^$f.....| 00000090 b9 01 00 e8 cf 00 8b da 66 8b 87 00 7e 66 25 ff |........f...~f%.| 000000a0 ff ff 0f 66 3d f8 ff ff 0f c3 33 c9 8e d9 8e c1 |...f=.....3.....| 000000b0 8e d1 66 bc f4 7b 00 00 bd 00 7c 66 0f b6 46 10 |..f..{....|f..F.| 000000c0 66 f7 66 24 66 0f b7 56 0e 66 03 56 1c 66 89 56 |f.f$f..V.f.V.f.V| 000000d0 f4 66 03 c2 66 89 46 fc 66 c7 46 f8 ff ff ff ff |.f..f.F.f.F.....| 000000e0 66 8b 46 2c 66 50 e8 af 00 bb 70 00 b9 01 00 e8 |f.F,fP....p.....| 000000f0 73 00 bf 00 07 b1 0b be a9 7d f3 a6 74 2a 03 f9 |s........}..t*..| 00000100 83 c7 15 81 ff 00 09 72 ec 66 40 4a 75 db 66 58 |[email protected]| 00000110 e8 47 ff 72 cf be b4 7d ac 84 c0 74 09 b4 0e bb |.G.r...}...t....| 00000120 07 00 cd 10 eb f2 cd 19 66 58 ff 75 09 ff 75 0f |........fX.u..u.| 00000130 66 58 bb 00 20 66 83 f8 02 72 da 66 3d f8 ff ff |fX.. f...r.f=...| 00000140 0f 73 d2 66 50 e8 50 00 0f b6 4e 0d e8 16 00 c1 |.s.fP.P...N.....| 00000150 e1 05 03 d9 66 58 53 e8 00 ff 5b 72 d8 8a 56 40 |....fXS...[r..V@| 00000160 ea 00 00 00 20 66 60 66 6a 00 66 50 53 6a 00 66 |.... f`fj.fPSj.f| 00000170 68 10 00 01 00 8b f4 b8 00 42 8a 56 40 cd 13 be |h........B.V@...| 00000180 c7 7d 72 94 67 83 44 24 06 20 66 67 ff 44 24 08 |.}r.g.D$. fg.D$.| 00000190 e2 e3 83 c4 10 66 61 c3 66 48 66 48 66 0f b6 56 |.....fa.fHfHf..V| 000001a0 0d 66 f7 e2 66 03 46 fc c3 4e 54 4c 44 52 20 20 |.f..f.F..NTLDR | 000001b0 20 20 20 20 0d 0a 4e 6f 20 53 79 73 74 65 6d 20 | ..No System | 000001c0 44 69 73 6b 20 6f 72 0d 0a 44 69 73 6b 20 49 2f |Disk or..Disk I/| 000001d0 4f 20 65 72 72 6f 72 0d 0a 50 72 65 73 73 20 61 |O error..Press a| 000001e0 20 6b 65 79 20 74 6f 20 72 65 73 74 61 72 74 0d | key to restart.| 000001f0 0a 00 00 00 00 00 00 00 00 00 00 00 00 00 55 aa |..............U.| 00000200 =============================== StdErr Messages: =============================== umount: /isodevice: device is busy. (In some cases useful info about processes that use the device is found by lsof(8) or fuser(1))

  Read the article

• Why did Ubuntu suddenly get so slow?

  - by user101383

  12.10 has been slowing down mysteriously. Normally, in past versions, I can log in, open Firefox, and it will pop up within seconds. 12.10 is like that upon install too, though once I install my old apps, it gets very slow by Ubuntu standards. After login the hard drive will just make noise for a while before the OS will do anything. Hardware: enter description: Desktop Computer product: XPS 8300 () vendor: Dell Inc. serial: B6G2WR1 width: 64 bits capabilities: smbios-2.6 dmi-2.6 vsyscall32 configuration: boot=normal chassis=desktop uuid=44454C4C-3600-1047-8032-C2C04F575231 core description: Motherboard product: 0Y2MRG vendor: Dell Inc. physical id: 0 version: A00 serial: ..CN7360419G04VQ. slot: To Be Filled By O.E.M. *cpu description: CPU product: Intel(R) Core(TM) i7-2600 CPU @ 3.40GHz vendor: Intel Corp. physical id: 4 bus info: cpu@0 version: Intel(R) Core(TM) i7-2600 CPU @ 3.40GHz serial: To Be Filled By O.E.M. slot: CPU 1 size: 1600MHz capacity: 1600MHz width: 64 bits clock: 100MHz capabilities: x86-64 fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp constant_tsc arch_perfmon pebs bts rep_good nopl xtopology nonstop_tsc aperfmperf pni pclmulqdq dtes64 monitor ds_cpl vmx smx est tm2 ssse3 cx16 xtpr pdcm pcid sse4_1 sse4_2 x2apic popcnt tsc_deadline_timer aes xsave avx lahf_lm ida arat epb xsaveopt pln pts dtherm tpr_shadow vnmi flexpriority ept vpid cpufreq configuration: cores=4 enabledcores=1 threads=2 *-cache:0 description: L1 cache physical id: 5 slot: L1-Cache size: 256KiB capacity: 256KiB capabilities: internal write-through unified *-cache:1 description: L2 cache physical id: 6 slot: L2-Cache size: 1MiB capacity: 1MiB capabilities: internal write-through unified *-cache:2 DISABLED description: L3 cache physical id: 7 slot: L3-Cache size: 8MiB capacity: 8MiB capabilities: internal write-back unified *-memory description: System Memory physical id: 20 slot: System board or motherboard size: 8GiB *-bank:0 description: SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) product: NT2GC64B88B0NF-CG vendor: Nanya physical id: 0 serial: 7228183 slot: DIMM3 size: 2GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:1 description: SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) product: NT2GC64B88B0NF-CG vendor: Nanya physical id: 1 serial: 1E28183 slot: DIMM1 size: 2GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:2 description: SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) product: NT2GC64B88B0NF-CG vendor: Nanya physical id: 2 serial: 9E28183 slot: DIMM4 size: 2GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:3 description: SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) product: NT2GC64B88B0NF-CG vendor: Nanya physical id: 3 serial: 5527183 slot: DIMM2 size: 2GiB width: 64 bits clock: 1333MHz (0.8ns) *-firmware description: BIOS vendor: Dell Inc. physical id: 0 version: A05 date: 09/21/2011 size: 64KiB capacity: 4032KiB capabilities: mca pci upgrade shadowing escd cdboot bootselect socketedrom edd int13floppy1200 int13floppy720 int13floppy2880 int5printscreen int9keyboard int14serial int17printer int10video acpi usb zipboot biosbootspecification *-pci description: Host bridge product: 2nd Generation Core Processor Family DRAM Controller vendor: Intel Corporation physical id: 100 bus info: pci@0000:00:00.0 version: 09 width: 32 bits clock: 33MHz *-pci:0 description: PCI bridge product: Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port vendor: Intel Corporation physical id: 1 bus info: pci@0000:00:01.0 version: 09 width: 32 bits clock: 33MHz capabilities: pci pm msi pciexpress normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:40 ioport:e000(size=4096) memory:fe600000-fe6fffff ioport:d0000000(size=268435456) *-display description: VGA compatible controller product: Juniper [Radeon HD 5700 Series] vendor: Advanced Micro Devices [AMD] nee ATI physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm pciexpress msi vga_controller bus_master cap_list rom configuration: driver=radeon latency=0 resources: irq:44 memory:d0000000-dfffffff memory:fe620000-fe63ffff ioport:e000(size=256) memory:fe600000-fe61ffff *-multimedia description: Audio device product: Juniper HDMI Audio [Radeon HD 5700 Series] vendor: Advanced Micro Devices [AMD] nee ATI physical id: 0.1 bus info: pci@0000:01:00.1 version: 00 width: 64 bits clock: 33MHz capabilities: pm pciexpress msi bus_master cap_list configuration: driver=snd_hda_intel latency=0 resources: irq:48 memory:fe640000-fe643fff *-communication description: Communication controller product: 6 Series/C200 Series Chipset Family MEI Controller #1 vendor: Intel Corporation physical id: 16 bus info: pci@0000:00:16.0 version: 04 width: 64 bits clock: 33MHz capabilities: pm msi bus_master cap_list configuration: driver=mei latency=0 resources: irq:45 memory:fe708000-fe70800f *-usb:0 description: USB controller product: 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 vendor: Intel Corporation physical id: 1a bus info: pci@0000:00:1a.0 version: 05 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:16 memory:fe707000-fe7073ff *-multimedia description: Audio device product: 6 Series/C200 Series Chipset Family High Definition Audio Controller vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 05 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=snd_hda_intel latency=0 resources: irq:46 memory:fe700000-fe703fff *-pci:1 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 1 vendor: Intel Corporation physical id: 1c bus info: pci@0000:00:1c.0 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:41 memory:fe500000-fe5fffff *-network description: Network controller product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=bcma-pci-bridge latency=0 resources: irq:16 memory:fe500000-fe503fff *-pci:2 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 4 vendor: Intel Corporation physical id: 1c.3 bus info: pci@0000:00:1c.3 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:42 memory:fe400000-fe4fffff *-network description: Ethernet interface product: NetLink BCM57788 Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 01 serial: 18:03:73:e1:a7:71 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.123 duplex=full firmware=sb ip=192.168.1.3 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:47 memory:fe400000-fe40ffff *-usb:1 description: USB controller product: 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 vendor: Intel Corporation physical id: 1d bus info: pci@0000:00:1d.0 version: 05 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:23 memory:fe706000-fe7063ff *-isa description: ISA bridge product: H67 Express Chipset Family LPC Controller vendor: Intel Corporation physical id: 1f bus info: pci@0000:00:1f.0 version: 05 width: 32 bits clock: 33MHz capabilities: isa bus_master cap_list configuration: latency=0 *-storage description: SATA controller product: 6 Series/C200 Series Chipset Family SATA AHCI Controller vendor: Intel Corporation physical id: 1f.2 bus info: pci@0000:00:1f.2 version: 05 width: 32 bits clock: 66MHz capabilities: storage msi pm ahci_1.0 bus_master cap_list configuration: driver=ahci latency=0 resources: irq:43 ioport:f070(size=8) ioport:f060(size=4) ioport:f050(size=8) ioport:f040(size=4) ioport:f020(size=32) memory:fe705000-fe7057ff *-serial UNCLAIMED description: SMBus product: 6 Series/C200 Series Chipset Family SMBus Controller vendor: Intel Corporation physical id: 1f.3 bus info: pci@0000:00:1f.3 version: 05 width: 64 bits clock: 33MHz configuration: latency=0 resources: memory:fe704000-fe7040ff ioport:f000(size=32) *-scsi:0 physical id: 1 logical name: scsi0 capabilities: emulated *-disk description: ATA Disk product: Hitachi HUA72201 vendor: Hitachi physical id: 0.0.0 bus info: scsi@0:0.0.0 logical name: /dev/sda version: JP4O serial: JPW9J0HD21BTZC size: 931GiB (1TB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 sectorsize=512 signature=000641dc *-volume:0 description: EXT4 volume vendor: Linux physical id: 1 bus info: scsi@0:0.0.0,1 logical name: /dev/sda1 logical name: / version: 1.0 serial: 4e3d91b7-fd38-4f44-a9e9-ba3c39b926ec size: 585GiB capacity: 585GiB capabilities: primary journaled extended_attributes large_files huge_files dir_nlink recover extents ext4 ext2 initialized configuration: created=2012-10-21 16:26:50 filesystem=ext4 lastmountpoint=/ modified=2012-10-29 18:12:08 mount.fstype=ext4 mount.options=rw,relatime,errors=remount-ro,data=ordered mounted=2012-10-29 18:12:08 state=mounted *-volume:1 description: Extended partition physical id: 2 bus info: scsi@0:0.0.0,2 logical name: /dev/sda2 size: 7823MiB capacity: 7823MiB capabilities: primary extended partitioned partitioned:extended *-logicalvolume description: Linux swap / Solaris partition physical id: 5 logical name: /dev/sda5 capacity: 7823MiB capabilities: nofs *-volume:2 description: Windows NTFS volume physical id: 3 bus info: scsi@0:0.0.0,3 logical name: /dev/sda3 version: 3.1 serial: 84a92aae-347b-7940-a2d1-f4745b885ef2 size: 337GiB capacity: 337GiB capabilities: primary bootable ntfs initialized configuration: clustersize=4096 created=2012-10-21 18:43:39 filesystem=ntfs modified_by_chkdsk=true mounted_on_nt4=true resize_log_file=true state=dirty upgrade_on_mount=true *-scsi:1 physical id: 2 logical name: scsi1 capabilities: emulated *-cdrom description: DVD-RAM writer product: DVDRWBD DH-12E3S vendor: PLDS physical id: 0.0.0 bus info: scsi@1:0.0.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/sr0 version: MD11 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc *-scsi:2 physical id: 3 bus info: usb@2:1.8 logical name: scsi6 capabilities: emulated scsi-host configuration: driver=usb-storage *-disk:0 description: SCSI Disk physical id: 0.0.0 bus info: scsi@6:0.0.0 logical name: /dev/sdb configuration: sectorsize=512 *-disk:1 description: SCSI Disk physical id: 0.0.1 bus info: scsi@6:0.0.1 logical name: /dev/sdc configuration: sectorsize=512 *-disk:2 description: SCSI Disk physical id: 0.0.2 bus info: scsi@6:0.0.2 logical name: /dev/sdd configuration: sectorsize=512 *-disk:3 description: SCSI Disk product: MS/MS-Pro vendor: Generic- physical id: 0.0.3 bus info: scsi@6:0.0.3 logical name: /dev/sde version: 1.03 serial: 3 capabilities: removable configuration: sectorsize=512 *-medium physical id: 0 logical name: /dev/sde

  Read the article

• The SPARC SuperCluster

  - by Karoly Vegh

  Oracle has been providing a lead in the Engineered Systems business for quite a while now, in accordance with the motto "Hardware and Software Engineered to Work Together." Indeed it is hard to find a better definition of these systems.  Allow me to summarize the idea. It is:  Build a compute platform optimized to run your technologies Develop application aware, intelligently caching storage components Take an impressively fast network technology interconnecting it with the compute nodes Tune the application to scale with the nodes to yet unseen performance Reduce the amount of data moving via compression Provide this all in a pre-integrated single product with a single-pane management interface All these ideas have been around in IT for quite some time now. The real Oracle advantage is adding the last one to put these all together. Oracle has built quite a portfolio of Engineered Systems, to run its technologies - and run those like they never ran before. In this post I'll focus on one of them that serves as a consolidation demigod, a multi-purpose engineered system.  As you probably have guessed, I am talking about the SPARC SuperCluster. It has many great features inherited from its predecessors, and it adds several new ones. Allow me to pick out and elaborate about some of the most interesting ones from a technological point of view.  I. It is the SPARC SuperCluster T4-4. That is, as compute nodes, it includes SPARC T4-4 servers that we learned to appreciate and respect for their features: The SPARC T4 CPUs: Each CPU has 8 cores, each core runs 8 threads. The SPARC T4-4 servers have 4 sockets. That is, a single compute node can in parallel, simultaneously  execute 256 threads. Now, a full-rack SPARC SuperCluster has 4 of these servers on board. Remember the keyword demigod.  While retaining the forerunner SPARC T3's exceptional throughput, the SPARC T4 CPUs raise the bar with single performance too - a humble 5x better one than their ancestors.  actually, the SPARC T4 CPU cores run in both single-threaded and multi-threaded mode, and switch between these two on-the-fly, fulfilling not only single-threaded OR multi-threaded applications' needs, but even mixed requirements (like in database workloads!). Data security, anyone? Every SPARC T4 CPU core has a built-in encryption engine, that is, encryption algorithms cast into silicon.  A PCI controller right on the chip for customers who need I/O performance.  Built-in, no-cost Virtualization:  Oracle VM for SPARC (the former LDoms or Logical Domains) is not a server-emulation virtualization technology but rather a serverpartitioning one, the hypervisor runs in the server firmware, and all the VMs' HW resources (I/O, CPU, memory) are accessed natively, without performance overhead.  This enables customers to run a number of Solaris 10 and Solaris 11 VMs separated, independent of each other within a physical server II. For Database performance, it includes Exadata Storage Cells - one of the main reasons why the Exadata Database Machine performs at diabolic speed. What makes them important? They provide DB backend storage for your Oracle Databases to run on the SPARC SuperCluster, that is what they are built and tuned for DB performance.  These storage cells are SQL-aware.  That is, if a SPARC T4 database compute node executes a query, it doesn't simply request tons of raw datablocks from the storage, filters the received data, and throws away most of it where the statement doesn't apply, but provides the SQL query to the storage node too. The storage cell software speaks SQL, that is, it is able to prefilter and through that transfer only the relevant data. With this, the traffic between database nodes and storage cells is reduced immensely. Less I/O is a good thing - as they say, all the CPUs of the world do one thing just as fast as any other - and that is waiting for I/O.  They don't only pre-filter, but also provide data preprocessing features - e.g. if a DB-node requests an aggregate of data, they can calculate it, and handover only the results, not the whole set. Again, less data to transfer.  They support the magical HCC, (Hybrid Columnar Compression). That is, data can be stored in a precompressed form on the storage. Less data to transfer.  Of course one can't simply rely on disks for performance, there is Flash Storage included there for caching.  III. The low latency, high-speed backbone network: InfiniBand, that interconnects all the members with: Real High Speed: 40 Gbit/s. Full Duplex, of course. Oh, and a really low latency.  RDMA. Remote Direct Memory Access. This technology allows the DB nodes to do exactly that. Remotely, directly placing SQL commands into the Memory of the storage cells. Dodging all the network-stack bottlenecks, avoiding overhead, placing requests directly into the process queue.  You can also run IP over InfiniBand if you please - that's the way the compute nodes can communicate with each other.  IV. Including a general-purpose storage too: the ZFSSA, which is a unified storage, providing NAS and SAN access too, with the following features:  NFS over RDMA over InfiniBand. Nothing is faster network-filesystem-wise.  All the ZFS features onboard, hybrid storage pools, compression, deduplication, snapshot, replication, NFS and CIFS shares Storageheads in a HA-Cluster configuration providing availability of the data  DTrace Live Analytics in a web-based Administration UI Being a general purpose application data storage for your non-database applications running on the SPARC SuperCluster over whichever protocol they prefer, easily replicating, snapshotting, cloning data for them.  There's a lot of great technology included in Oracle's SPARC SuperCluster, we have talked its interior through. As for external scalability: you can start with a half- of full- rack SPARC SuperCluster, and scale out to several racks - that is, stacking not separate full-rack SPARC SuperClusters, but extending always one large instance of the size of several full-racks. Yes, over InfiniBand network. Add racks as you grow.  What technologies shall run on it? SPARC SuperCluster is a general purpose scaleout consolidation/cloud environment. You can run Oracle Databases with RAC scaling, or Oracle Weblogic (end enjoy the SPARC T4's advantages to run Java). Remember, Oracle technologies have been integrated with the Oracle Engineered Systems - this is the Oracle on Oracle advantage. But you can run other software environments such as SAP if you please too. Run any application that runs on Oracle Solaris 10 or Solaris 11. Separate them in Virtual Machines, or even Oracle Solaris Zones, monitor and manage those from a central UI. Here the key takeaways once again: The SPARC SuperCluster: Is a pre-integrated Engineered System Contains SPARC T4-4 servers with built-in virtualization, cryptography, dynamic threading Contains the Exadata storage cells that intelligently offload the burden of the DB-nodes  Contains a highly available ZFS Storage Appliance, that provides SAN/NAS storage in a unified way Combines all these elements over a high-speed, low-latency backbone network implemented with InfiniBand Can grow from a single half-rack to several full-rack size Supports the consolidation of hundreds of applications To summarize: All these technologies are great by themselves, but the real value is like in every other Oracle Engineered System: Integration. All these technologies are tuned to perform together. Together they are way more than the sum of all - and a careful and actually very time consuming integration process is necessary to orchestrate all these for performance. The SPARC SuperCluster's goal is to enable infrastructure operations and offer a pre-integrated solution that can be architected and delivered in hours instead of months of evaluations and tests. The tedious and most importantly time and resource consuming part of the work - testing and evaluating - has been done.  Now go, provide services.   -- charlie  

  Read the article

• CodePlex Daily Summary for Tuesday, June 12, 2012

  CodePlex Daily Summary for Tuesday, June 12, 2012Popular ReleasesWeapsy - ASP.NET MVC CMS: 1.0 RC: - Upgrade to Entity Framework 4.3.1 - Added AutoMapper custom version (by nopCommerce Team) - Added missed model properties and localization resources of Plugin Definitions - Minor changes - Fixed some bugsSolution Extender for Microsoft Dynamics CRM 2011: Solution Extender (1.0.0.0): Initial releaseQTP FT Uninstaller: QTP FT Uninstaller v3: - KnowledgeInbox has made this tool open source - Converted to C# - Better scanning & cleaning mechanismWebSocket4Net: WebSocket4Net 0.7: Changes included in this release: updated ClientEngine added proper exception handling code added state support for callback added property AllowUnstrustedCertificate for JsonWebSocket added properties for sending ping automatically improved JsBridge fixed a uri compatibility issueXenta Framework - extensible enterprise n-tier application framework: Xenta Framework 1.8.0 Beta: Catalog and Publication reviews and ratings Store language packs in data base Improve reporting system Improve Import/Export system A lot of WebAdmin app UI improvements Initial implementation of the WebForum app DB indexes Improve and simplify architecture Less abstractions Modernize architecture Improve, simplify and unify API Simplify and improve testing A lot of new unit tests Codebase refactoring and ReSharpering Utilize Castle Windsor Utilize NHibernate ORM ...Microsoft Ajax Minifier: Microsoft Ajax Minifier 4.55: Properly handle IE extension to CSS3 grammar that allows for multiple parameters to functional pseudo-class selectors. add new switch -braces:(new|same) that affects where opening braces are placed in multi-line output. The default, "new" puts them on their own new line; "same" outputs them at the end of the previous line. add new optional values to the -inline switch: -inline:(force|noforce), which can be combined with the existing boolean value via comma-separators; value "force" (which...Microsoft Media Platform: Player Framework: MMP Player Framework 2.7 (Silverlight and WP7): Additional DownloadsSMFv2.7 Full Installer (MSI) - This will install everything you need in order to develop your own SMF player application, including the IIS Smooth Streaming Client. It only includes the assemblies. If you want the source code please follow the link above. Smooth Streaming Sample Player - This is a pre-built player that includes support for IIS Smooth Streaming. You can configure the player to playback your content by simplying editing a configuration file - no need to co...Liberty: v3.2.1.0 Release 10th June 2012: Change Log -Added -Liberty is now digitally signed! If the certificate on Liberty.exe is missing, invalid, or does not state that it was developed by "Xbox Chaos, Open Source Developer," your copy of Liberty may have been altered in some (possibly malicious) way. -Reach Mass biped max health and shield changer -Fixed -H3/ODST Fixed all of the glitches that users kept reporting (also reverted the changes made in 3.2.0.2) -Reach Made some tag names clearer and more consistent between m...SHA-1 Hash Checker: SHA-1 Hash Checker (for Windows): Fixed major bugs. Removed false negatives.AutoUpdaterdotNET: AutoUpdater.NET 1.0: Everything seems perfect if you find any problem you can report to http://www.rbsoft.org/contact.htmlMedia Companion: Media Companion 3.503b: It has been a while, so it's about time we release another build! Major effort has been for fixing trailer downloads, plus a little bit of work for episode guide tag in TV show NFOs.Microsoft SQL Server Product Samples: Database: AdventureWorks Sample Reports 2008 R2: AdventureWorks Sample Reports 2008 R2.zip contains several reports include Sales Reason Comparisons SQL2008R2.rdl which uses Adventure Works DW 2008R2 as a data source reference. For more information, go to Sales Reason Comparisons report.Json.NET: Json.NET 4.5 Release 7: Fix - Fixed Metro build to pass Windows Application Certification Kit on Windows 8 Release Preview Fix - Fixed Metro build error caused by an anonymous type Fix - Fixed ItemConverter not being used when serializing dictionaries Fix - Fixed an incorrect object being passed to the Error event when serializing dictionaries Fix - Fixed decimal properties not being correctly ignored with DefaultValueHandlingLINQ Extensions Library: 1.0.3.0: New to release 1.0.3.0:Combinatronics: Combinations (unique) Combinations (with repetition) Permutations (unique) Permutations (with repetition) Convert jagged arrays to fixed multidimensional arrays Convert fixed multidimensional arrays to jagged arrays ElementAtMax ElementAtMin ElementAtAverage New set of array extension (1.0.2.8):Rotate Flip Resize (maintaing data) Split Fuse Replace Append and Prepend extensions (1.0.2.7) IndexOf extensions (1.0.2.7) Ne...????????API for .Net SDK: SDK for .Net ??? Release 1: 6?12????? ??? - ?????.net2.0?.net4.0????Winform?Web???????。 NET2 - .net 2.0?Winform?Web???? NET4 - .net 4.0?Winform?Web???? Libs - SDK ???，??2.0?4.0?SDK??? 6?11????? ??? - ?Entities???????????EntityBase，???ToString()???????json???，??????4.0???????。2.0?3.5???！ ??? - Request????????AccessToken??????source=appkey?????。????，????????，???????public_timeline?????????。 ?? - ???ClinetLogin??????????RefreshToken???????false???。 ?? - ???RepostTimeline????Statuses???null???。 ?? - Utility?Bui...Audio Pitch & Shift: Audio Pitch And Shift 4.5.0: Added Instruments tab for modules Open folder content feature Some bug fixesPython Tools for Visual Studio: 1.5 Beta 1: We’re pleased to announce the release of Python Tools for Visual Studio 1.5 Beta. Python Tools for Visual Studio (PTVS) is an open-source plug-in for Visual Studio which supports programming with the Python language. PTVS supports a broad range of features including: • Supports CPython, IronPython, Jython and PyPy • Python editor with advanced member, signature intellisense and refactoring • Code navigation: “Find all refs”, goto definition, and object browser • Local and remote debugging •...Circuit Diagram: Circuit Diagram 2.0 Beta 1: New in this release: Automatically flip components when placing Delete components using keyboard delete key Resize document Document properties window Print document Recent files list Confirm when exiting with unsaved changes Thumbnail previews in Windows Explorer for CDDX files Show shortcut keys in toolbox Highlight selected item in toolbox Zoom using mouse scroll wheel while holding down ctrl key Plugin support for: Custom export formats Custom import formats Open...Umbraco CMS: Umbraco CMS 5.2 Beta: The future of Umbracov5 represents the future architecture of Umbraco, so please be aware that while it's technically superior to v4 it's not yet on a par feature or performance-wise. What's new? For full details see our http://progress.umbraco.org task tracking page showing all items complete for 5.2. In a nutshellPackage Builder Starter Kits Dynamic Extension Methods Querying / IsHelpers Friendly alt template URLs Localization Various bug fixes / performance enhancements Gett...JayData - The cross-platform HTML5 data-management library for JavaScript: JayData 1.0.5: JayData is a unified data access library for JavaScript developers to query and update data from different sources like WebSQL, IndexedDB, OData, Facebook or YQL. See it in action in this 6 minutes video New features in JayData 1.0.5http://jaydata.org/blog/jaydata-1.0.5-is-here-with-authentication-support-and-more http://jaydata.org/blog/release-notes Sencha Touch 2 module (read-only)This module can be used to bind data retrieved by JayData to Sencha Touch 2 generated user interface. (exam...New ProjectsAFS.Aspnet.Collab.Site: alles umfassender testAFS.FallBackService: Afs.ultimate.fallbackserviceAIMS: This project aims at creating an mvc-based application for NGO portfolio management.Card Douglas: Project for card discountCrashReporter.NET: Send crash reports for c# or vb.net applications directly to your mail's inbox Daphne Translator - localizing tool for Daphne: This project was created as a helper project for localization Daphne checkers software [url:http://daphne.codeplex.com]. It can be used by other developers to do translations of resources. Daphne Translator is done to be extensible by any resource type of localized texts. ExcelFileEditor: This project is a free excel file editor class library . ( Support " .xls and .xlsx " )Finegypt: Fin EgyptHuish: Huish MarineINNO DNN Open Registration: The INNO DNN Registration module collection allows for customized DotNetNuke registration, payment processing integration, profile management, transaction history and a powerful contact us form. It is built to be responsive to allow registration on mobile devices such as Android phones and tablets, iPad, iPhone and more. Key focus is on extensibility including options to hook your own custom DotNetNuke modules into it for consistent, easy registration of users.jCardView: jCardViewLinkCard: D? án VDOS - TopLinkLINQ Expression Projection: Project Description LINQ Expression Projection library provides tool that enable using lambda expressions in LINQ projections (to anonymous and predefined types) even if the lambda expression is not defined in the query but rather is stored in a variable or retrieved via a function or property. Goal This library is a tool for development of applications following the DRY principle. It is used to facilitate reuse LINQ expressions.MD5 Message-Digest Algorithm for Microsoft® .NET Micro Framework: MD5 Message-Digest Algorithm for Microsoft® .NET Micro FrameworkMoney Class for C#. Fast, light and flexible: This Money class gives you the ability to work with money of multiple currencies as if it were built-in types. It looks and behaves like a decimal with extra features, but can perform much faster.NCT-Medical Record System: I've created this project for learning purposes onlyPaiPaiAPI: ??SDKParadise Shop: sâsâsaPingyThingy: PingyThingy is a basic application that will allow you to ping multiple hosts.SCK - Spine Model Creation Kit: The SCK is a software package for generating FE spine models from a set of anatomical parameters.ScoreMS（????????）: The summary is required.SiteCoreDynamicForm: This project's aim is to provide a simple solution in SiteCore for creating dynamic formsSmall Media Library (for Games and other 3D rendering applications): A .NET library that utilises DirectShow to render video into a block of memory that can be easily written to surfaces managed by rendering APIs such as DirectX and OpenGL, or used in any other way the host application requires.SportStore: The project has only training purpose. It is an ecommerce web application to sell sport products on line.Thesis Management System: This is a Thesis Management System(TMIS),Based on a three-tier structure,This is a open source project.There are many question and bugs ,I will repair by other time.This PowerShell script will output details of your default organization.: This is a PowerShell script. You can save this PowerShell file 'DefaultCRMOrganization.ps1' to your server. Microsoft Dynamics CRM administrators and professionals can have a quick browse through the details for their default organization by simply running this file. Note: Sometimes when you run this file, for first time, it might open in Notepad. In order to open this file with a PowerShell application, associate this file (with extension ps1) with C:\Windows\System32\WindowsPowerShell...Tmib Dreampad: Dream Pad is a smart text editor by Tmib Inc. Tags - Notepad , Texteditor , Note Pad , Dream Pad , Wordpad , Word Pad, TmibUAIFAI: Trabalho de EDUmbraco Dynamic Form: This project's aim is to provide a simple solution for creating dynamic forms in UmbracoVDOS - Top Link: H? th?ng tích di?m LinkCardVoteChecker: Vote Checker allows a canvasser to identify a valid Ballot by checking if the corresponding barcode is known to the election committee.WebRozklady: sWindows Application Monitoring and Administration Tool: This projects aims at developing client server architecture based windows application monitoring, administring and deployment. Also Most of the real life applications today are either windows services or Websites. WINADM suite aims at monitoring these and providing the user a graphical interface for interaction with these services.WPF 3 D: How to study wpf

  Read the article

• Das T5-4 TPC-H Ergebnis naeher betrachtet

  - by Stefan Hinker

  Inzwischen haben vermutlich viele das neue TPC-H Ergebnis der SPARC T5-4 gesehen, das am 7. Juni bei der TPC eingereicht wurde.  Die wesentlichen Punkte dieses Benchmarks wurden wie gewohnt bereits von unserer Benchmark-Truppe auf  "BestPerf" zusammengefasst.  Es gibt aber noch einiges mehr, das eine naehere Betrachtung lohnt. Skalierbarkeit Das TPC raet von einem Vergleich von TPC-H Ergebnissen in unterschiedlichen Groessenklassen ab.  Aber auch innerhalb der 3000GB-Klasse ist es interessant: SPARC T4-4 mit 4 CPUs (32 Cores mit 3.0 GHz) liefert 205,792 QphH. SPARC T5-4 mit 4 CPUs (64 Cores mit 3.6 GHz) liefert 409,721 QphH. Das heisst, es fehlen lediglich 1863 QphH oder 0.45% zu 100% Skalierbarkeit, wenn man davon ausgeht, dass die doppelte Anzahl Kerne das doppelte Ergebnis liefern sollte.  Etwas anspruchsvoller, koennte man natuerlich auch einen Faktor von 2.4 erwarten, wenn man die hoehere Taktrate mit beruecksichtigt.  Das wuerde die Latte auf 493901 QphH legen.  Dann waere die SPARC T5-4 bei 83%.  Damit stellt sich die Frage: Was hat hier nicht skaliert?  Vermutlich der Plattenspeicher!  Auch hier lohnt sich eine naehere Betrachtung: Plattenspeicher Im Bericht auf BestPerf und auch im Full Disclosure Report der TPC stehen einige interessante Details zum Plattenspeicher und der Konfiguration.   In der Konfiguration der SPARC T4-4 wurden 12 2540-M2 Arrays verwendet, die jeweils ca. 1.5 GB/s Durchsatz liefert, insgesamt also eta 18 GB/s.  Dabei waren die Arrays offensichtlich mit jeweils 2 Kabeln pro Array direkt an die 24 8GBit FC-Ports des Servers angeschlossen.  Mit den 2x 8GBit Ports pro Array koennte man so ein theoretisches Maximum von 2GB/s erreichen.  Tatsaechlich wurden 1.5GB/s geliefert, was so ziemlich dem realistischen Maximum entsprechen duerfte. Fuer den Lauf mit der SPARC T5-4 wurden doppelt so viele Platten verwendet.  Dafuer wurden die 2540-M2 Arrays mit je einem zusaetzlichen Plattentray erweitert.  Mit dieser Konfiguration wurde dann (laut BestPerf) ein Maximaldurchsatz von 33 GB/s erreicht - nicht ganz das doppelte des SPARC T4-4 Laufs.  Um tatsaechlich den doppelten Durchsatz (36 GB/s) zu liefern, haette jedes der 12 Arrays 3 GB/s ueber seine 4 8GBit Ports liefern muessen.  Im FDR stehen nur 12 dual-port FC HBAs, was die Verwendung der Brocade FC Switches erklaert: Es wurden alle 4 8GBit ports jedes Arrays an die Switches angeschlossen, die die Datenstroeme dann in die 24 16GBit HBA ports des Servers buendelten.  Das theoretische Maximum jedes Storage-Arrays waere nun 4 GB/s.  Wenn man jedoch den Protokoll- und "Realitaets"-Overhead mit einrechnet, sind die tatsaechlich gelieferten 2.75 GB/s gar nicht schlecht.  Mit diesen Zahlen im Hinterkopf ist die Verdopplung des SPARC T4-4 Ergebnisses eine gute Leistung - und gleichzeitig eine gute Erklaerung, warum nicht bis zum 2.4-fachen skaliert wurde. Nebenbei bemerkt: Weder die SPARC T4-4 noch die SPARC T5-4 hatten in der gemessenen Konfiguration irgendwelche Flash-Devices. Mitbewerb Seit die T4 Systeme auf dem Markt sind, bemuehen sich unsere Mitbewerber redlich darum, ueberall den Eindruck zu hinterlassen, die Leistung des SPARC CPU-Kerns waere weiterhin mangelhaft.  Auch scheinen sie ueberzeugt zu sein, dass (ueber)grosse Caches und hohe Taktraten die einzigen Schluessel zu echter Server Performance seien.  Wenn ich mir nun jedoch die oeffentlichen TPC-H Ergebnisse ansehe, sehe ich dies: TPC-H @3000GB, Non-Clustered Systems System QphH SPARC T5-4 3.6 GHz SPARC T5 4/64 – 2048 GB 409,721.8 SPARC T4-4 3.0 GHz SPARC T4 4/32 – 1024 GB 205,792.0 IBM Power 780 4.1 GHz POWER7 8/32 – 1024 GB 192,001.1 HP ProLiant DL980 G7 2.27 GHz Intel Xeon X7560 8/64 – 512 GB 162,601.7 Kurz zusammengefasst: Mit 32 Kernen (mit 3 GHz und 4MB L3 Cache), liefert die SPARC T4-4 mehr QphH@3000GB ab als IBM mit ihrer 32 Kern Power7 (bei 4.1 GHz und 32MB L3 Cache) und auch mehr als HP mit einem 64 Kern Intel Xeon System (2.27 GHz und 24MB L3 Cache).  Ich frage mich, wo genau SPARC hier mangelhaft ist? Nun koennte man natuerlich argumentieren, dass beide Ergebnisse nicht gerade neu sind.  Nun, in Ermangelung neuerer Ergebnisse kann man ja mal ein wenig spekulieren: IBMs aktueller Performance Report listet die o.g. IBM Power 780 mit einem rPerf Wert von 425.5.  Ein passendes Nachfolgesystem mit Power7+ CPUs waere die Power 780+ mit 64 Kernen, verfuegbar mit 3.72 GHz.  Sie wird mit einem rPerf Wert von  690.1 angegeben, also 1.62x mehr.  Wenn man also annimmt, dass Plattenspeicher nicht der limitierende Faktor ist (IBM hat mit 177 SSDs getestet, sie duerfen das gerne auf 400 erhoehen) und IBMs eigene Leistungsabschaetzung zugrunde legt, darf man ein theoretisches Ergebnis von 311398 QphH@3000GB erwarten.  Das waere dann allerdings immer noch weit von dem Ergebnis der SPARC T5-4 entfernt, und gerade in der von IBM so geschaetzen "per core" Metric noch weniger vorteilhaft. In der x86-Welt sieht es nicht besser aus.  Leider gibt es von Intel keine so praktischen rPerf-Tabellen.  Daher muss ich hier fuer eine Schaetzung auf SPECint_rate2006 zurueckgreifen.  (Ich bin kein grosser Fan von solchen Kreuz- und Querschaetzungen.  Insb. SPECcpu ist nicht besonders geeignet, um Datenbank-Leistung abzuschaetzen, da fast kein IO im Spiel ist.)  Das o.g. HP System wird bei SPEC mit 1580 CINT2006_rate gelistet.  Das bis einschl. 2013-06-14 beste Resultat fuer den neuen Intel Xeon E7-4870 mit 8 CPUs ist 2180 CINT2006_rate.  Das ist immerhin 1.38x besser.  (Wenn man nur die Taktrate beruecksichtigen wuerde, waere man bei 1.32x.)  Hier weiter zu rechnen, ist muessig, aber fuer die ungeduldigen Leser hier eine kleine tabellarische Zusammenfassung: TPC-H @3000GB Performance Spekulationen System QphH* Verbesserung gegenueber der frueheren Generation SPARC T4-4 32 cores SPARC T4 205,792 2x SPARC T5-464 cores SPARC T5 409,721 IBM Power 780 32 cores Power7 192,001 1.62x IBM Power 780+ 64 cores Power7+  311,398* HP ProLiant DL980 G764 cores Intel Xeon X7560 162,601 1.38x HP ProLiant DL980 G780 cores Intel Xeon E7-4870    224,348* * Keine echten Resultate  - spekulative Werte auf der Grundlage von rPerf (Power7+) oder SPECint_rate2006 (HP) Natuerlich sind IBM oder HP herzlich eingeladen, diese Werte zu widerlegen.  Aber stand heute warte ich noch auf aktuelle Benchmark Veroffentlichungen in diesem Datensegment. Was koennen wir also zusammenfassen? Es gibt einige Hinweise, dass der Plattenspeicher der begrenzende Faktor war, der die SPARC T5-4 daran hinderte, auf jenseits von 2x zu skalieren Der Mythos, dass SPARC Kerne keine Leistung bringen, ist genau das - ein Mythos.  Wie sieht es umgekehrt eigentlich mit einem TPC-H Ergebnis fuer die Power7+ aus? Cache ist nicht der magische Performance-Schalter, fuer den ihn manche Leute offenbar halten. Ein System, eine CPU-Architektur und ein Betriebsystem jenseits einer gewissen Grenze zu skalieren ist schwer.  In der x86-Welt scheint es noch ein wenig schwerer zu sein. Was fehlt?  Nun, das Thema Preis/Leistung ueberlasse ich gerne den Verkaeufern ;-) Und zu guter Letzt: Nein, ich habe mich nicht ins Marketing versetzen lassen.  Aber manchmal kann ich mich einfach nicht zurueckhalten... Disclosure Statements The views expressed on this blog are my own and do not necessarily reflect the views of Oracle. TPC-H, QphH, $/QphH are trademarks of Transaction Processing Performance Council (TPC). For more information, see www.tpc.org, results as of 6/7/13. Prices are in USD. SPARC T5-4 409,721.8 QphH@3000GB, $3.94/QphH@3000GB, available 9/24/13, 4 processors, 64 cores, 512 threads; SPARC T4-4 205,792.0 QphH@3000GB, $4.10/QphH@3000GB, available 5/31/12, 4 processors, 32 cores, 256 threads; IBM Power 780 QphH@3000GB, 192,001.1 QphH@3000GB, $6.37/QphH@3000GB, available 11/30/11, 8 processors, 32 cores, 128 threads; HP ProLiant DL980 G7 162,601.7 QphH@3000GB, $2.68/QphH@3000GB available 10/13/10, 8 processors, 64 cores, 128 threads. SPEC and the benchmark names SPECfp and SPECint are registered trademarks of the Standard Performance Evaluation Corporation. Results as of June 18, 2013 from www.spec.org. HP ProLiant DL980 G7 (2.27 GHz, Intel Xeon X7560): 1580 SPECint_rate2006; HP ProLiant DL980 G7 (2.4 GHz, Intel Xeon E7-4870): 2180 SPECint_rate2006,

  Read the article

• Full-text Indexing Books Online

  - by Most Valuable Yak (Rob Volk)

  While preparing for a recent SQL Saturday presentation, I was struck by a crazy idea (shocking, I know): Could someone import the content of SQL Server Books Online into a database and apply full-text indexing to it?  The answer is yes, and it's really quite easy to do. The first step is finding the installed help files.  If you have SQL Server 2012, BOL is installed under the Microsoft Help Library.  You can find the install location by opening SQL Server Books Online and clicking the gear icon for the Help Library Manager.  When the new window pops up click the Settings link, you'll get the following: You'll see the path under Library Location. Once you navigate to that path you'll have to drill down a little further, to C:\ProgramData\Microsoft\HelpLibrary\content\Microsoft\store.  This is where the help file content is kept if you downloaded it for offline use. Depending on which products you've downloaded help for, you may see a few hundred files.  Fortunately they're named well and you can easily find the "SQL_Server_Denali_Books_Online_" files.  We are interested in the .MSHC files only, and can skip the Installation and Developer Reference files. Despite the .MHSC extension, these files are compressed with the standard Zip format, so your favorite archive utility (WinZip, 7Zip, WinRar, etc.) can open them.  When you do, you'll see a few thousand files in the archive.  We are only interested in the .htm files, but there's no harm in extracting all of them to a folder.  7zip provides a command-line utility and the following will extract to a D:\SQLHelp folder previously created: 7z e –oD:\SQLHelp "C:\ProgramData\Microsoft\HelpLibrary\content\Microsoft\store\SQL_Server_Denali_Books_Online_B780_SQL_110_en-us_1.2.mshc" *.htm Well that's great Rob, but how do I put all those files into a full-text index? I'll tell you in a second, but first we have to set up a few things on the database side.  I'll be using a database named Explore (you can certainly change that) and the following setup is a fragment of the script I used in my presentation: USE Explore; GO CREATE SCHEMA help AUTHORIZATION dbo; GO -- Create default fulltext catalog for later FT indexes CREATE FULLTEXT CATALOG FTC AS DEFAULT; GO CREATE TABLE help.files(file_id int not null IDENTITY(1,1) CONSTRAINT PK_help_files PRIMARY KEY, path varchar(256) not null CONSTRAINT UNQ_help_files_path UNIQUE, doc_type varchar(6) DEFAULT('.xml'), content varbinary(max) not null); CREATE FULLTEXT INDEX ON help.files(content TYPE COLUMN doc_type LANGUAGE 1033) KEY INDEX PK_help_files; This will give you a table, default full-text catalog, and full-text index on that table for the content you're going to insert.  I'll be using the command line again for this, it's the easiest method I know: for %a in (D:\SQLHelp\*.htm) do sqlcmd -S. -E -d Explore -Q"set nocount on;insert help.files(path,content) select '%a', cast(c as varbinary(max)) from openrowset(bulk '%a', SINGLE_CLOB) as c(c)" You'll need to copy and run that as one line in a command prompt.  I'll explain what this does while you run it and watch several thousand files get imported: The "for" command allows you to loop over a collection of items.  In this case we want all the .htm files in the D:\SQLHelp folder.  For each file it finds, it will assign the full path and file name to the %a variable.  In the "do" clause, we'll specify another command to be run for each iteration of the loop.  I make a call to "sqlcmd" in order to run a SQL statement.  I pass in the name of the server (-S.), where "." represents the local default instance. I specify -d Explore as the database, and -E for trusted connection.  I then use -Q to run a query that I enclose in double quotes. The query uses OPENROWSET(BULK…SINGLE_CLOB) to open the file as a data source, and to treat it as a single character large object.  In order for full-text indexing to work properly, I have to convert the text content to varbinary. I then INSERT these contents along with the full path of the file into the help.files table created earlier.  This process continues for each file in the folder, creating one new row in the table. And that's it! 5 SQL Statements and 2 command line statements to unzip and import SQL Server Books Online!  In case you're wondering why I didn't use FILESTREAM or FILETABLE, it's simply because I haven't learned them…yet. I may return to this blog after I figure that out and update it with the steps to do so.  I believe that will make it even easier. In the spirit of exploration, I'll leave you to work on some fulltext queries of this content.  I also recommend playing around with the sys.dm_fts_xxxx DMVs (I particularly like sys.dm_fts_index_keywords, it's pretty interesting).  There are additional example queries in the download material for my presentation linked above. Many thanks to Kevin Boles (t) for his advice on (re)checking the content of the help files.  Don't let that .htm extension fool you! The 2012 help files are actually XML, and you'd need to specify '.xml' in your document type column in order to extract the full-text keywords.  (You probably noticed this in the default definition for the doc_type column.)  You can query sys.fulltext_document_types to get a complete list of the types that can be full-text indexed. I also need to thank Hilary Cotter for giving me the original idea. I believe he used MSDN content in a full-text index for an article from waaaaaaaaaaay back, that I can't find now, and had forgotten about until just a few days ago.  He is also co-author of Pro Full-Text Search in SQL Server 2008, which I highly recommend.  He also has some FTS articles on Simple Talk: http://www.simple-talk.com/sql/learn-sql-server/sql-server-full-text-search-language-features/ http://www.simple-talk.com/sql/learn-sql-server/sql-server-full-text-search-language-features,-part-2/

  Read the article

• Microphone not capturing sound on 12.04 Lenovo G580

  - by Yam Marcovic

  In both Skype and the Sound Recorder application, I am not capturing any audio from my built-in microphone. I'm not sure why. Otherwise, sound output is working well. I have tried running gstreamer-properties and setting the Default Input plugin to PulseAUdio as well (to match the output), and it didn't help. I have tried running alsamixer -V all and I only get 2 input-related entries: Capture(L R) which is on 100 and not muted (can't be either), and Analog Mic Boost which is on 20db. Extra info: Camera (video) is working well on Skype and Kamerka. Can you please help me get my microphone to work? lspci: 00:00.0 Host bridge: Intel Corporation Ivy Bridge DRAM Controller (rev 09) Subsystem: Lenovo Device 3977 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) (prog-if 00 [VGA controller]) Subsystem: Lenovo Device 3977 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 42 Region 0: Memory at e0000000 (64-bit, non-prefetchable) [size=4M] Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M] Region 4: I/O ports at 3000 [size=64] Expansion ROM at <unassigned> [disabled] Capabilities: <access denied> Kernel driver in use: i915 Kernel modules: i915 00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) (prog-if 30 [XHCI]) Subsystem: Lenovo Device 3977 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 41 Region 0: Memory at e0600000 (64-bit, non-prefetchable) [size=64K] Capabilities: <access denied> Kernel driver in use: xhci_hcd 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) Subsystem: Lenovo Device 3977 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 43 Region 0: Memory at e0614000 (64-bit, non-prefetchable) [size=16] Capabilities: <access denied> Kernel driver in use: mei Kernel modules: mei 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) (prog-if 20 [EHCI]) Subsystem: Lenovo Device 3977 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at e0619000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) Subsystem: Lenovo Device 3977 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 44 Region 0: Memory at e0610000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 00002000-00002fff Memory behind bridge: e0500000-e05fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 2 (rev c4) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 Memory behind bridge: e0400000-e04fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) (prog-if 20 [EHCI]) Subsystem: Lenovo Device 3977 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 0: Memory at e0618000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) Subsystem: Lenovo Device 3977 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel modules: iTCO_wdt 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] (rev 04) (prog-if 01 [AHCI 1.0]) Subsystem: Lenovo Device 3977 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 40 Region 0: I/O ports at 3088 [size=8] Region 1: I/O ports at 3094 [size=4] Region 2: I/O ports at 3080 [size=8] Region 3: I/O ports at 3090 [size=4] Region 4: I/O ports at 3060 [size=32] Region 5: Memory at e0617000 (32-bit, non-prefetchable) [size=2K] Capabilities: <access denied> Kernel driver in use: ahci 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) Subsystem: Lenovo Device 3977 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin C routed to IRQ 10 Region 0: Memory at e0615000 (64-bit, non-prefetchable) [size=256] Region 4: I/O ports at 3040 [size=32] Kernel modules: i2c-i801 01:00.0 Ethernet controller: Atheros Communications Inc. AR8162 Fast Ethernet (rev 08) Subsystem: Lenovo Device 3979 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 11 Region 0: Memory at e0500000 (64-bit, non-prefetchable) [size=256K] Region 2: I/O ports at 2000 [size=128] Capabilities: <access denied> 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) Subsystem: Lenovo Device 31a1 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 17 Region 0: Memory at e0400000 (64-bit, non-prefetchable) [size=64K] Capabilities: <access denied> Kernel driver in use: ath9k Kernel modules: ath9k aplay -l **** List of PLAYBACK Hardware Devices **** card 0: PCH [HDA Intel PCH], device 0: CONEXANT Analog [CONEXANT Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: PCH [HDA Intel PCH], device 3: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0

  Read the article

• DTracing TCP congestion control

  - by user12820842

  In a previous post, I showed how we can use DTrace to probe TCP receive and send window events. TCP receive and send windows are in effect both about flow-controlling how much data can be received - the receive window reflects how much data the local TCP is prepared to receive, while the send window simply reflects the size of the receive window of the peer TCP. Both then represent flow control as imposed by the receiver. However, consider that without the sender imposing flow control, and a slow link to a peer, TCP will simply fill up it's window with sent segments. Dealing with multiple TCP implementations filling their peer TCP's receive windows in this manner, busy intermediate routers may drop some of these segments, leading to timeout and retransmission, which may again lead to drops. This is termed congestion, and TCP has multiple congestion control strategies. We can see that in this example, we need to have some way of adjusting how much data we send depending on how quickly we receive acknowledgement - if we get ACKs quickly, we can safely send more segments, but if acknowledgements come slowly, we should proceed with more caution. More generally, we need to implement flow control on the send side also. Slow Start and Congestion Avoidance From RFC2581, let's examine the relevant variables: "The congestion window (cwnd) is a sender-side limit on the amount of data the sender can transmit into the network before receiving an acknowledgment (ACK). Another state variable, the slow start threshold (ssthresh), is used to determine whether the slow start or congestion avoidance algorithm is used to control data transmission" Slow start is used to probe the network's ability to handle transmission bursts both when a connection is first created and when retransmission timers fire. The latter case is important, as the fact that we have effectively lost TCP data acts as a motivator for re-probing how much data the network can handle from the sending TCP. The congestion window (cwnd) is initialized to a relatively small value, generally a low multiple of the sending maximum segment size. When slow start kicks in, we will only send that number of bytes before waiting for acknowledgement. When acknowledgements are received, the congestion window is increased in size until cwnd reaches the slow start threshold ssthresh value. For most congestion control algorithms the window increases exponentially under slow start, assuming we receive acknowledgements. We send 1 segment, receive an ACK, increase the cwnd by 1 MSS to 2*MSS, send 2 segments, receive 2 ACKs, increase the cwnd by 2*MSS to 4*MSS, send 4 segments etc. When the congestion window exceeds the slow start threshold, congestion avoidance is used instead of slow start. During congestion avoidance, the congestion window is generally updated by one MSS for each round-trip-time as opposed to each ACK, and so cwnd growth is linear instead of exponential (we may receive multiple ACKs within a single RTT). This continues until congestion is detected. If a retransmit timer fires, congestion is assumed and the ssthresh value is reset. It is reset to a fraction of the number of bytes outstanding (unacknowledged) in the network. At the same time the congestion window is reset to a single max segment size. Thus, we initiate slow start until we start receiving acknowledgements again, at which point we can eventually flip over to congestion avoidance when cwnd ssthresh. Congestion control algorithms differ most in how they handle the other indication of congestion - duplicate ACKs. A duplicate ACK is a strong indication that data has been lost, since they often come from a receiver explicitly asking for a retransmission. In some cases, a duplicate ACK may be generated at the receiver as a result of packets arriving out-of-order, so it is sensible to wait for multiple duplicate ACKs before assuming packet loss rather than out-of-order delivery. This is termed fast retransmit (i.e. retransmit without waiting for the retransmission timer to expire). Note that on Oracle Solaris 11, the congestion control method used can be customized. See here for more details. In general, 3 or more duplicate ACKs indicate packet loss and should trigger fast retransmit . It's best not to revert to slow start in this case, as the fact that the receiver knew it was missing data suggests it has received data with a higher sequence number, so we know traffic is still flowing. Falling back to slow start would be excessive therefore, so fast recovery is used instead. Observing slow start and congestion avoidance The following script counts TCP segments sent when under slow start (cwnd ssthresh). #!/usr/sbin/dtrace -s #pragma D option quiet tcp:::connect-request / start[args[1]-cs_cid] == 0/ { start[args[1]-cs_cid] = 1; } tcp:::send / start[args[1]-cs_cid] == 1 && args[3]-tcps_cwnd tcps_cwnd_ssthresh / { @c["Slow start", args[2]-ip_daddr, args[4]-tcp_dport] = count(); } tcp:::send / start[args[1]-cs_cid] == 1 && args[3]-tcps_cwnd args[3]-tcps_cwnd_ssthresh / { @c["Congestion avoidance", args[2]-ip_daddr, args[4]-tcp_dport] = count(); } As we can see the script only works on connections initiated since it is started (using the start[] associative array with the connection ID as index to set whether it's a new connection (start[cid] = 1). From there we simply differentiate send events where cwnd ssthresh (congestion avoidance). Here's the output taken when I accessed a YouTube video (where rport is 80) and from an FTP session where I put a large file onto a remote system. # dtrace -s tcp_slow_start.d ^C ALGORITHM RADDR RPORT #SEG Slow start 10.153.125.222 20 6 Slow start 138.3.237.7 80 14 Slow start 10.153.125.222 21 18 Congestion avoidance 10.153.125.222 20 1164 We see that in the case of the YouTube video, slow start was exclusively used. Most of the segments we sent in that case were likely ACKs. Compare this case - where 14 segments were sent using slow start - to the FTP case, where only 6 segments were sent before we switched to congestion avoidance for 1164 segments. In the case of the FTP session, the FTP data on port 20 was predominantly sent with congestion avoidance in operation, while the FTP session relied exclusively on slow start. For the default congestion control algorithm - "newreno" - on Solaris 11, slow start will increase the cwnd by 1 MSS for every acknowledgement received, and by 1 MSS for each RTT in congestion avoidance mode. Different pluggable congestion control algorithms operate slightly differently. For example "highspeed" will update the slow start cwnd by the number of bytes ACKed rather than the MSS. And to finish, here's a neat oneliner to visually display the distribution of congestion window values for all TCP connections to a given remote port using a quantization. In this example, only port 80 is in use and we see the majority of cwnd values for that port are in the 4096-8191 range. # dtrace -n 'tcp:::send { @q[args[4]-tcp_dport] = quantize(args[3]-tcps_cwnd); }' dtrace: description 'tcp:::send ' matched 10 probes ^C 80 value ------------- Distribution ------------- count -1 | 0 0 |@@@@@@ 5 1 | 0 2 | 0 4 | 0 8 | 0 16 | 0 32 | 0 64 | 0 128 | 0 256 | 0 512 | 0 1024 | 0 2048 |@@@@@@@@@ 8 4096 |@@@@@@@@@@@@@@@@@@@@@@@@@@ 23 8192 | 0

  Read the article

• Kubuntu 12.04 - Touchpad and keyboard stopped working at random

  - by StepTNT

  As in the title, I've got this problem with my Kubuntu 12.04. At first I've thought that the whole system was hung, but it happened again 5 minutes ago and, while the keyboard and the touchpad stopped working, the music was still playing, so I guess that's just an "input" problem, because the system was still working! Any solution? Is there some data that you need to know about my setup? EDIT: Added my lshw outout description: Notebook product: N53SV () vendor: ASUSTeK Computer Inc. version: 1.0 serial: B2N0AS17695408A width: 64 bits capabilities: smbios-2.6 dmi-2.6 vsyscall32 configuration: boot=normal chassis=notebook family=N uuid=8083F2DA-A43E-E081-3F3F-BCAEC55F8AA1 *-core description: Motherboard product: N53SV vendor: ASUSTeK Computer Inc. physical id: 0 version: 1.0 serial: BSN12345678901234567 slot: MIDDLE *-firmware description: BIOS vendor: American Megatrends Inc. physical id: 0 version: N53SV.214 date: 08/10/2011 size: 64KiB capacity: 2496KiB capabilities: pci upgrade shadowing cdboot bootselect edd int13floppy1200 int13floppy720 int13floppy2880 int5printscreen int9keyboard int14serial int17printer acpi usb smartbattery biosbootspecification *-cpu description: CPU product: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz vendor: Intel Corp. physical id: 4 bus info: cpu@0 version: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz serial: To Be Filled By O.E.M. slot: CPU 1 size: 800MHz capacity: 4GHz width: 64 bits clock: 100MHz capabilities: x86-64 fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp constant_tsc arch_perfmon pebs bts rep_good nopl xtopology nonstop_tsc aperfmperf pni pclmulqdq dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm pcid sse4_1 sse4_2 x2apic popcnt tsc_deadline_timer xsave avx lahf_lm ida arat epb xsaveopt pln pts tpr_shadow vnmi flexpriority ept vpid cpufreq configuration: cores=4 enabledcores=1 threads=2 *-cache description: L1 cache physical id: 5 slot: L1-Cache size: 32KiB capacity: 32KiB capabilities: internal write-back instruction *-memory description: System Memory physical id: 40 slot: System board or motherboard size: 10GiB *-bank:0 description: SODIMM DDR3 Synchronous 1333 MHz (0,8 ns) product: 99U5428-040.A00LF vendor: Kingston physical id: 0 serial: 103C28C3 slot: ChannelA-DIMM0 size: 4GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:1 description: SODIMM DDR3 Synchronous 1333 MHz (0,8 ns) product: HMT325S6BFR8C-H9 vendor: Hynix/Hyundai physical id: 1 serial: 58383D1F slot: ChannelA-DIMM1 size: 2GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:2 description: SODIMM DDR3 Synchronous 1333 MHz (0,8 ns) product: HMT325S6BFR8C-H9 vendor: Hynix/Hyundai physical id: 2 serial: 58183D19 slot: ChannelB-DIMM0 size: 2GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:3 description: SODIMM DDR3 Synchronous 1333 MHz (0,8 ns) product: HMT325S6BFR8C-H9 vendor: Hynix/Hyundai physical id: 3 serial: 58183C8F slot: ChannelB-DIMM1 size: 2GiB width: 64 bits clock: 1333MHz (0.8ns) *-pci description: Host bridge product: 2nd Generation Core Processor Family DRAM Controller vendor: Intel Corporation physical id: 100 bus info: pci@0000:00:00.0 version: 09 width: 32 bits clock: 33MHz configuration: driver=agpgart-intel resources: irq:0 *-pci:0 description: PCI bridge product: Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port vendor: Intel Corporation physical id: 1 bus info: pci@0000:00:01.0 version: 09 width: 32 bits clock: 33MHz capabilities: pci pm msi pciexpress normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:40 ioport:d000(size=4096) memory:db000000-dc0fffff ioport:c0000000(size=301989888) *-generic UNCLAIMED description: Unassigned class product: Illegal Vendor ID vendor: Illegal Vendor ID physical id: 0 bus info: pci@0000:01:00.0 version: ff width: 32 bits clock: 66MHz capabilities: bus_master vga_palette cap_list configuration: latency=255 maxlatency=255 mingnt=255 resources: memory:db000000-dbffffff memory:c0000000-cfffffff memory:d0000000-d1ffffff ioport:d000(size=128) memory:dc000000-dc07ffff *-display description: VGA compatible controller product: 2nd Generation Core Processor Family Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 09 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:47 memory:dc400000-dc7fffff memory:b0000000-bfffffff ioport:e000(size=64) *-communication description: Communication controller product: 6 Series/C200 Series Chipset Family MEI Controller #1 vendor: Intel Corporation physical id: 16 bus info: pci@0000:00:16.0 version: 04 width: 64 bits clock: 33MHz capabilities: pm msi bus_master cap_list configuration: driver=mei latency=0 resources: irq:48 memory:df00b000-df00b00f *-usb:0 description: USB controller product: 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 vendor: Intel Corporation physical id: 1a bus info: pci@0000:00:1a.0 version: 05 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:16 memory:df008000-df0083ff *-multimedia description: Audio device product: 6 Series/C200 Series Chipset Family High Definition Audio Controller vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 05 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=snd_hda_intel latency=0 resources: irq:49 memory:df000000-df003fff *-pci:1 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 1 vendor: Intel Corporation physical id: 1c bus info: pci@0000:00:1c.0 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:41 ioport:c000(size=4096) memory:de600000-deffffff ioport:d4200000(size=10485760) *-pci:2 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 2 vendor: Intel Corporation physical id: 1c.1 bus info: pci@0000:00:1c.1 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:42 ioport:b000(size=4096) memory:ddc00000-de5fffff ioport:d3700000(size=10485760) *-network description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 01 serial: 48:5d:60:f2:2c:fd width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-24-generic firmware=N/A ip=192.168.1.6 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:ddc00000-ddc0ffff *-pci:3 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 4 vendor: Intel Corporation physical id: 1c.3 bus info: pci@0000:00:1c.3 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:43 ioport:a000(size=4096) memory:dd200000-ddbfffff ioport:d2c00000(size=10485760) *-usb description: USB controller product: FL1000G USB 3.0 Host Controller vendor: Fresco Logic physical id: 0 bus info: pci@0000:04:00.0 version: 04 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress xhci bus_master cap_list configuration: driver=xhci_hcd latency=0 resources: irq:19 memory:dd200000-dd20ffff *-pci:4 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 6 vendor: Intel Corporation physical id: 1c.5 bus info: pci@0000:00:1c.5 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:44 ioport:9000(size=4096) memory:dc800000-dd1fffff ioport:d2100000(size=10485760) *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 06 serial: bc:ae:c5:5f:8a:a1 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl_nic/rtl8168e-2.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:46 ioport:9000(size=256) memory:d2104000-d2104fff memory:d2100000-d2103fff *-usb:1 description: USB controller product: 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 vendor: Intel Corporation physical id: 1d bus info: pci@0000:00:1d.0 version: 05 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:23 memory:df007000-df0073ff *-isa description: ISA bridge product: HM65 Express Chipset Family LPC Controller vendor: Intel Corporation physical id: 1f bus info: pci@0000:00:1f.0 version: 05 width: 32 bits clock: 33MHz capabilities: isa bus_master cap_list configuration: latency=0 *-storage description: SATA controller product: 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller vendor: Intel Corporation physical id: 1f.2 bus info: pci@0000:00:1f.2 logical name: scsi0 logical name: scsi2 version: 05 width: 32 bits clock: 66MHz capabilities: storage msi pm ahci_1.0 bus_master cap_list emulated configuration: driver=ahci latency=0 resources: irq:45 ioport:e0b0(size=8) ioport:e0a0(size=4) ioport:e090(size=8) ioport:e080(size=4) ioport:e060(size=32) memory:df006000-df0067ff *-disk description: ATA Disk product: ST9750420AS vendor: Seagate physical id: 0 bus info: scsi@0:0.0.0 logical name: /dev/sda version: 0002 serial: 5WS0A7QR size: 698GiB (750GB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 signature=e0c5913d *-volume:0 description: Windows FAT volume vendor: MSDOS5.0 physical id: 1 bus info: scsi@0:0.0.0,1 logical name: /dev/sda1 version: FAT32 serial: 4ce5-3acb size: 3004MiB capacity: 3004MiB capabilities: primary fat initialized configuration: FATs=2 filesystem=fat *-volume:1 description: EXT4 volume vendor: Linux physical id: 2 bus info: scsi@0:0.0.0,2 logical name: /dev/sda2 logical name: / version: 1.0 serial: c198cc2a-d86a-4460-a4d5-3fc0b21e439c size: 28GiB capacity: 28GiB capabilities: primary journaled extended_attributes large_files huge_files dir_nlink recover extents ext4 ext2 initialized configuration: created=2012-03-15 16:53:54 filesystem=ext4 lastmountpoint=/ modified=2012-05-02 18:52:04 mount.fstype=ext4 mount.options=rw,relatime,errors=remount-ro,user_xattr,acl,barrier=1,data=ordered mounted=2012-05-09 19:06:01 state=mounted *-volume:2 description: Windows NTFS volume physical id: 3 bus info: scsi@0:0.0.0,3 logical name: /dev/sda3 version: 3.1 serial: 4c1cdebc-ec09-2947-a3b5-c1f9f1cddc1c size: 152GiB capacity: 152GiB capabilities: primary bootable ntfs initialized configuration: clustersize=4096 created=2011-02-22 16:02:47 filesystem=ntfs label=OS state=clean *-volume:3 description: Extended partition physical id: 4 bus info: scsi@0:0.0.0,4 logical name: /dev/sda4 size: 514GiB capacity: 514GiB capabilities: primary extended partitioned partitioned:extended *-logicalvolume:0 description: Linux swap / Solaris partition physical id: 5 logical name: /dev/sda5 capacity: 10GiB capabilities: nofs *-logicalvolume:1 description: HPFS/NTFS partition physical id: 6 logical name: /dev/sda6 capacity: 504GiB *-cdrom description: DVD-RAM writer product: BD-MLT UJ240AS vendor: MATSHITA physical id: 1 bus info: scsi@2:0.0.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/sr0 version: 1.00 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc *-serial UNCLAIMED description: SMBus product: 6 Series/C200 Series Chipset Family SMBus Controller vendor: Intel Corporation physical id: 1f.3 bus info: pci@0000:00:1f.3 version: 05 width: 64 bits clock: 33MHz configuration: latency=0 resources: memory:df005000-df0050ff ioport:e040(size=32)

  Read the article

• «Oracle E-Business Suite: ERP DBA????»??

  - by user10821858

  ????????,???????4????,????????????????????,?????????«Oracle E-Business Suite:ERP DBA????»????????????????????????,??????????????“??”,????????????,???????????,???????????????????,????,????,?????????????????????????,???????????????,????????????????????,??????????,????????????????????????:1.????????????????????2.??DBA???ERP??,??????????3.???????????,?????????????????????ERP??????4.?????????ERP????????5.??????????????ERP????????????6.??ERP???????????????????7.????CIO???ERP???????????8.????????????????????????? ?:?????????????:http://vdisk.weibo.com/s/6X-ze ?:?????:http://product.dangdang.com/product.aspx?product_id=22788613 ?:?????:http://book.360buy.com/11021724.html ?:?????:http://product.china-pub.com/3661378 ?:?????:http://www.amazon.cn/dp/B008BFNAX0 ?:?????:http://detail.tmall.com/item.htm?id=18024644999 ????,?????????????????????????! ? ? ???? ERP ????????????20 ?,?Oracle ??????(E-Business Suite)? ????????ERP ????,????????????????,???????? ????????,????????????? ??ERP ???,?????????????ERP DBA ????????ERP DBA ???????DBA ????????????:ERP DBA ??????????,?? ???ERP ????????,????????????????????????? ?,???????????????????,ERP DBA ????????????? ??????,?Oracle ???????????ERP ??,?????????,?? ???????????,?????????ERP DBA ??????,??????? ????ERP ?????,???????????????? ???????????ERP DBA ?????,?????????????ERP ? ???,???ERP ??????????,????????????????ERP ? ?????????,??????????ERP ????,?????:“?????? ??,????????”,???“????”????????????????,? ??ERP DBA ?????,?????????????,????????????? ???“????”??,?“??????”???,??????????????, ??????,???????????????????“????,??????”, ???????????,??????????????,???????????? ????????,????????????ERP ????,????ERP ???? ????? ?????? ????7 ?,???????3 ?:?????????????? ???(?1 ~ 2 ?):??????Oracle ????????????????? ???????,??????????ERP ???????????????,??? ???? ???(?3 ~ 6 ?):?3 ????Oracle ERP ?????????????;?4 ????Oracle ERP ???????ERP ????;?5 ??????Oracle ????? ??????????????;?6 ?????????????????ERP ???? ??? ?????(?7 ?):????????Oracle ERP ??????????,??? ??????????????????????,???????????????? ?,????????????????????????????????????? ???? ????????????: (1)????,?????????????????????????????? ?,???????????????????,?????????????????? ??????,??????????????????????? (2)???,???,??????,??????????????????Oracle ERP ???????????,????;????????????Oracle ERP ??? ??????????,????? (3)????????,???????????????????????,?? ?????????,???????????????????????????;?? ERP DBA ????????????,????????????????????,? ???????????,????????,???????????? ??????? (1)Oracle ERP ??????????????????ERP ???????? (2)???ERP ?????????DBA ????IT ????? (3)??????????????????? ??????? ?????????????,??????????????,????????? ???????????????????????????????,???????? ??????: E-Mail:longchun.zhu-AT-gmail-DOT-com ?? “?????,?????”,???????????????“?????”??? ?????????????,???????????????????????? ?????????????????,??Mike?Charles???????????, ????????????????????,??????????????????? ??????? ? ? ? ? ?1 ? Oracle ??????/1 1.1 Oracle ?????????????/2 1.2 Oracle ??????R12 /3 1.2.1 R12 ???????/3 1.2.2 R12 ???/4 1.3 ????/5 ?2 ? ERP ????/6 2.1 ERP ??????/7 2.1.1 ERP ??????????/7 2.1.2 ERP ?????????/8 2.1.3 ERP ??????/8 2.2 ??????/9 2.2.1 ????????/9 2.2.2 ???????/11 2.2.3 ?????????/12 2.3 ??ERP ?????????/14 2.3.1 ????/14 2.3.2 ??????/15 2.3.3 ????/16 2.3.4 ?????/19 2.3.5 ????/19 2.3.6 ??????/23 2.3.7 ???????/25 2.3.8 ????/26 2.3.9 ???????/27 2.4 ????/28 2.5 ????/29 ?3 ? Oracle ERP ??/31 3.1 ?????/32 3.1.1 ?????? /32 3.1.2 ????/34 3.1.3 ????/35 3.1.4 ????/37 3.1.5 ?????/37 3.1.6 ??Bug ??/39 3.1.7 ????/40 3.2 Oracle ??????R12 ???/42 3.2.1 ????/42 3.2.2 ???????/43 3.2.3 ????/43 3.2.4 ??????/60 3.3 ??????????????/62 3.3.1 ???????/62 3.3.2 ??DNS ???/63 3.3.3 ????Oracle ??????/63 3.3.4 ?????/64 3.4 ????/66 ?4 ? ??????ERP ????/67 4.1 ???????/68 4.2 ??????/81 4.3 ??????/83 4.4 ??????/85 4.4.1 ??????????/86 4.4.2 ????????????/86 4.4.3 ??????ERP ????/87 4.5 ???????????/89 4.6 ?????/89 4.6.1 ???????/90 4.6.2 ???????/92 4.6.3 ??redo ??/95 4.6.4 ??????/96 4.7 ????/98 4.7.1 ???????/98 4.7.2 ?????/99 4.7.3 ???????/100 4.7.4 ??????/100 4.7.5 ?????/101 4.8 ????????? /101 4.8.1 ????/102 4.8.2 ??DNS ???/102 4.8.3 ??sendmail /103 4.8.4 ??IMAP ??? /104 4.8.5 ??Oracle Alert /104 4.8.6 ??Workflow Mail /110 4.8.7 ???????/115 4.9 ?? Forms Socket ??/121 4.10 ????????/123 4.11 ?????????? /124 4.11.1 ???????/124 4.11.2 ???????/125 4.12 ???? /127 ?5 ? Oracle ???????????/128 5.1 Oracle ????????/129 5.1.1 ???/129 5.1.2 ???/130 5.1.3 ????/131 5.1.4 ????/131 5.2 ????????/131 5.2.1 Oracle ?????????????/131 5.2.2 Oracle ??????????/133 5.3 ??????/134 5.3.1 ???????????????/135 5.3.2 AutoPatch/136 5.3.3 AutoConfig/138 5.4 Rapid Clone/141 5.4.1 ????????????/141 5.4.2 ?????/142 5.4.3 ??????/145 5.4.4 ?Clone ?? /146 5.4.5 ??????????/146 5.4.6 Clone ??/148 5.4.7 Clone ??????? /150 5.4.8 ??Clone/157 5.5 OAM ??/158 5.5.1 OAM ?????/158 5.5.2 OAM ????????/158 5.5.3 ????????/159 5.5.4 ????????????/159 5.5.5 ????????/164 5.5.6 OAM ??????/168 5.6 ????/171 ?6 ? ???????/172 6.1 ??Oracle ??????/173 6.1.1 ??Form ?HTML ??/173 6.1.2 ????????/182 6.1.3 ????/187 6.2 ????/192 6.2.1 ?????/193 6.2.2 ????? /193 6.2.3 ?????/194 6.3 ???????/195 6.4 ?????/205 6.4.1 “??”?????/205 6.4.2 ???????/206 6.4.3 ??? /207 6.4.4 ??????? /208 6.4.5 ????????? /208 6.4.6 ??????/209 6.4.7 ???????/218 6.4.8 ??????/225 6.5 ??????/237 6.5.1 ??????/237 6.5.2 ??????/239 6.6 ????/245 ?7 ? ERP ???????/246 7.1 ERP ??????/247 7.2 ERP ???????/247 7.2.1 ????????/248 7.2.2 ?????????/248 7.2.3 ?????????/249 7.2.4 ???????/249 7.3 ????????/249 7.3.1 ERP ???????/249 7.3.2 ????/251 7.3.3 ????/251 7.3.4 ????/253 7.3.5 ????/255 7.4 ERP ??????/255 7.4.1 ????????/255 7.4.2 ???????/256 7.4.3 ?????????/257 7.5 ?????ERP ??/260 7.5.1 ????????/260 7.5.2 ????/261 7.5.3 ??????/262 7.5.4 ????????/273 7.6 ERP ????/280 7.6.1 ??X-Windows/280 7.6.2 ???????/281 7.6.3 ?????????/281 7.6.4 ??redo ??/282 7.6.5 ??opmn.xml ??/283 7.6.6 ???????/283 7.6.7 ??Apache ??/285 7.6.8 Forms Server socket ????/285 7.6.9 ??Forms Dead Client ??/286 7.6.10 ??Cancel Query /287 7.6.11 ??????????/288 7.6.12 ????????/293 7.6.13 ?? GSM ??/294 7.6.14 ??“ICX:????”/297 7.6.15 ????????/298 7.6.16 ???????/302 7.7 ??????/305 7.7.1 ?????/305 7.7.2 ????/305 7.7.3 ?????/305 7.7.4 ???????/306 7.7.5 ??????/306 7.8 ????????/306 7.8.1 ???CSI Number /307 7.8.2 ???SR /307 7.8.3 TAR ??/307 7.8.4 ????/307 7.9 ????/308

  Read the article

• How to find and fix issue with Pound and HAProxy

  - by javano

  Pound sits in front of HAProxy (on the same box) to perform SSL off-load. Requests are passed to 127.0.0.1:80 where HAProxy then balances the requests across backend servers for a hosted ASP .NET web app. A user is getting HTTP error 500 (Internal Server Error) returned to their browser this morning and I can see it is comming from Pound. They see no log entry in their web app (IIS) server logs, so its not hitting the back end servers. I think the problem is possibly with HAProxy. Lets review the logs: Initialy the users (1.2.3.4) hits Pound on the load balancer: Nov 12 10:02:24 lb1 pound: a-website.com 1.2.3.4 - - [12/Nov/2012:10:02:23 +0000] "POST /eventmanagement/EditEvent.aspx?eventOid=623fc423-2329-4cab-8be5-72a97709570d HTTP/1.1" 200 155721 "https://a-website.com/eventmanagement/EditEvent.aspx?eventOid=623fc423-2329-4cab-8be5-72a97709570d" "Mozilla/5.0 (Windows NT 6.2; WOW64) AppleWebKit/537.4 (KHTML, like Gecko) Chrome/22.0.1229.96 Safari/537.4" Nov 12 10:02:24 lb1 pound: a-website.com 1.2.3.4 - - [12/Nov/2012:10:02:24 +0000] "GET /Controls/ReferringOrganisationLogoImageHandler.ashx HTTP/1.1" 200 142 "https://a-website.com/eventmanagement/EditEvent.aspx?eventOid=623fc423-2329-4cab-8be5-72a97709570d" "Mozilla/5.0 (Windows NT 6.2; WOW64) AppleWebKit/537.4 (KHTML, like Gecko) Chrome/22.0.1229.96 Safari/537.4" Nov 12 10:02:24 lb1 pound: a-website.com 1.2.3.4 - - [12/Nov/2012:10:02:24 +0000] "GET /eventmanagement/WebCoreModule.ashx?__ac=1&__ac_wcmid=RAWCIL&__ac_lib=Radactive.WebControls.ILoad&__ac_key=RAWVCO_11&__ac_sid=fnoz2hmvirfivb2btbubbw45&__ac_cn=&__ac_cp=BVDXDWFLDWFMHDFJBOEGBDFLFOD5EEFD&__ac_fr=634883113445054092&__ac_ssid= HTTP/1.1" 200 11206 "https://a-website.com/eventmanagement/EditEvent.aspx?eventOid=623fc423-2329-4cab-8be5-72a97709570d" "Mozilla/5.0 (Windows NT 6.2; WOW64) AppleWebKit/537.4 (KHTML, like Gecko) Chrome/22.0.1229.96 Safari/537.4" Nov 12 10:02:24 lb1 pound: a-website.com 1.2.3.4 - - [12/Nov/2012:10:02:24 +0000] "GET /eventmanagement/WebCoreModule.ashx?__ac=1&__ac_wcmid=RAWCIL&__ac_lib=Radactive.WebControls.ILoad&__ac_key=RAWCCIL_11&__ac_sid=fnoz2hmvirfivb2btbubbw45&__ac_cn=&__ac_cp=BVDXDWFLDWFMHDFJBOEGBDFLFOD5EEFD&__ac_fr=634883113445054092 HTTP/1.1" 200 43496 "https://a-website.com/eventmanagement/EditEvent.aspx?eventOid=623fc423-2329-4cab-8be5-72a97709570d" "Mozilla/5.0 (Windows NT 6.2; WOW64) AppleWebKit/537.4 (KHTML, like Gecko) Chrome/22.0.1229.96 Safari/537.4" Nov 12 10:02:42 lb1 pound: (7f819fff8700) e500 for 1.2.3.4 response error read from 127.0.0.1:80/POST /eventmanagement/EditEvent.aspx?eventOid=623fc423-2329-4cab-8be5-72a97709570d HTTP/1.1: Connection timed out (15.121 secs) Above we can see the request comming in from the user at IP address 1.2.3.4, eventually Pound returns error 500 with the message "Connection timed out (15.121 secs)". Running HAProxy in debug mode, we can see the request come in; user@box:/var/log$ sudo /etc/init.d/haproxy restart Restarting haproxy: haproxy[WARNING] 316/100042 (19218) : <debug> mode incompatible with <quiet> and <daemon>. Keeping <debug> only. Available polling systems : sepoll : pref=400, test result OK epoll : pref=300, test result OK poll : pref=200, test result OK select : pref=150, test result OK Total: 4 (4 usable), will use sepoll. Using sepoll() as the polling mechanism. ....... 00000008:iis-servers.srvrep[0008:0009]: HTTP/1.1 200 OK 00000008:iis-servers.srvhdr[0008:0009]: Cache-Control: private 00000008:iis-servers.srvhdr[0008:0009]: Pragma: no-cache 00000008:iis-servers.srvhdr[0008:0009]: Content-Length: 22211 00000008:iis-servers.srvhdr[0008:0009]: Content-Type: text/plain; charset=utf-8 00000008:iis-servers.srvhdr[0008:0009]: Server: Microsoft-IIS/7.0 00000008:iis-servers.srvhdr[0008:0009]: X-AspNet-Version: 2.0.50727 00000008:iis-servers.srvhdr[0008:0009]: X-Powered-By: ASP.NET 00000008:iis-servers.srvhdr[0008:0009]: Date: Mon, 12 Nov 2012 10:01:25 GMT 00000009:iis-servers.accept(0004)=000a from [127.0.0.1:53556] 00000009:iis-servers.clireq[000a:ffff]: GET /Logoff.aspx HTTP/1.1 00000009:iis-servers.clihdr[000a:ffff]: Host: a-website.com 00000009:iis-servers.clihdr[000a:ffff]: Connection: keep-alive 00000009:iis-servers.clihdr[000a:ffff]: User-Agent: Mozilla/5.0 (Windows NT 6.2; WOW64) AppleWebKit/537.4 (KHTML, like Gecko) Chrome/22.0.1229.96 Safari/537.4 00000009:iis-servers.clihdr[000a:ffff]: Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 00000009:iis-servers.clihdr[000a:ffff]: Referer: https://a-website.com/eventmanagement/eventmanagement.aspx 00000009:iis-servers.clihdr[000a:ffff]: Accept-Encoding: gzip,deflate,sdch 00000009:iis-servers.clihdr[000a:ffff]: Accept-Language: en-GB,en;q=0.8,it;q=0.6 00000009:iis-servers.clihdr[000a:ffff]: Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.3 00000009:iis-servers.clihdr[000a:ffff]: Cookie: ASP.NET_SessionId=fnoz2hmvirfivb2btbubbw45; apps=apps2; AuthHint=true; __utma=190546871.552451749.1340295610.1352454675.1352711624.159; __utmb=190546871.2.10.1352711624; __utmc=190546871; __utmz=190546871.1349966519.143.3.utmcsr=en.wikipedia.org|utmccn=(referral)|utmcmd=referral|utmcct=/wiki/Single_transferable_vote; Sequence=162; SessionId=80e603f9-7e73-474b-8b7c-e198b2f11218; SecureSessionId=00000000-0000-0000-0000-000000000000; __utma=58336506.1016936529.1332752550.1352454680.1352711626.456; __utmb=58336506.28.10.1352711626; __utmc=58336506; __utmz=58336506.1352711626.456.155.utmcsr=a-website.com|utmccn=(referral)|utmcmd=referral|utmcct=/ 00000009:iis-servers.clihdr[000a:ffff]: X-SSL-cipher: RC4-SHA SSLv3 Kx=RSA Au=RSA Enc=RC4(128) Mac=SHA1 00000009:iis-servers.clihdr[000a:ffff]: X-Forwarded-For: 1.2.3.4 00000008:iis-servers.srvcls[0008:0009] 00000008:iis-servers.clicls[0008:0009] 00000008:iis-servers.closed[0008:0009] ....... 0000000e:iis-servers.srvrep[0008:0009]: HTTP/1.1 200 OK 0000000e:iis-servers.srvhdr[0008:0009]: Cache-Control: no-cache 0000000e:iis-servers.srvhdr[0008:0009]: Pragma: no-cache 0000000e:iis-servers.srvhdr[0008:0009]: Content-Length: 12805 0000000e:iis-servers.srvhdr[0008:0009]: Content-Type: text/html; charset=utf-8 0000000e:iis-servers.srvhdr[0008:0009]: Server: Microsoft-IIS/7.0 0000000e:iis-servers.srvhdr[0008:0009]: X-AspNet-Version: 2.0.50727 0000000e:iis-servers.srvhdr[0008:0009]: X-Powered-By: ASP.NET 0000000e:iis-servers.srvhdr[0008:0009]: Date: Mon, 12 Nov 2012 10:02:22 GMT 0000000f:iis-servers.accept(0004)=000c from [127.0.0.1:53609] 0000000f:iis-servers.clireq[000c:ffff]: GET /Controls/ReferringOrganisationLogoImageHandler.ashx HTTP/1.1 0000000f:iis-servers.clihdr[000c:ffff]: Host: a-website.com 0000000f:iis-servers.clihdr[000c:ffff]: Connection: keep-alive 0000000f:iis-servers.clihdr[000c:ffff]: User-Agent: Mozilla/5.0 (Windows NT 6.2; WOW64) AppleWebKit/537.4 (KHTML, like Gecko) Chrome/22.0.1229.96 Safari/537.4 0000000f:iis-servers.clihdr[000c:ffff]: Accept: */* 0000000f:iis-servers.clihdr[000c:ffff]: Referer: https://a-website.com/eventmanagement/EditEvent.aspx?eventOid=623fc423-2329-4cab-8be5-72a97709570d 0000000f:iis-servers.clihdr[000c:ffff]: Accept-Encoding: gzip,deflate,sdch 0000000f:iis-servers.clihdr[000c:ffff]: Accept-Language: en-GB,en;q=0.8,it;q=0.6 0000000f:iis-servers.clihdr[000c:ffff]: Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.3 0000000f:iis-servers.clihdr[000c:ffff]: Cookie: ASP.NET_SessionId=fnoz2hmvirfivb2btbubbw45; apps=apps2; __utma=190546871.552451749.1340295610.1352454675.1352711624.159; __utmb=190546871.2.10.1352711624; __utmc=190546871; __utmz=190546871.1349966519.143.3.utmcsr=en.wikipedia.org|utmccn=(referral)|utmcmd=referral|utmcct=/wiki/Single_transferable_vote; AuthHint=true; __utma=58336506.1016936529.1332752550.1352454680.1352711626.456; __utmb=58336506.33.10.1352711626; __utmc=58336506; __utmz=58336506.1352711626.456.155.utmcsr=a-website.com|utmccn=(referral)|utmcmd=referral|utmcct=/; SessionId=69cd415c-2f4e-4ace-b8f7-926d054f87c2; SecureSessionId=00000000-0000-0000-0000-000000000000; Sequence=170 0000000f:iis-servers.clihdr[000c:ffff]: X-SSL-cipher: RC4-SHA SSLv3 Kx=RSA Au=RSA Enc=RC4(128) Mac=SHA1 0000000f:iis-servers.clihdr[000c:ffff]: X-Forwarded-For: 1.2.3.4 0000000f:iis-servers.srvrep[000c:000d]: HTTP/1.1 200 OK 0000000f:iis-servers.srvhdr[000c:000d]: Cache-Control: private 0000000f:iis-servers.srvhdr[000c:000d]: Content-Length: 142 0000000f:iis-servers.srvhdr[000c:000d]: Content-Type: image/png 0000000f:iis-servers.srvhdr[000c:000d]: Server: Microsoft-IIS/7.0 0000000f:iis-servers.srvhdr[000c:000d]: X-AspNet-Version: 2.0.50727 0000000f:iis-servers.srvhdr[000c:000d]: Set-Cookie: SessionId=69cd415c-2f4e-4ace-b8f7-926d054f87c2; path=/ 0000000f:iis-servers.srvhdr[000c:000d]: Set-Cookie: SecureSessionId=00000000-0000-0000-0000-000000000000; path=/; secure 0000000f:iis-servers.srvhdr[000c:000d]: X-Powered-By: ASP.NET 0000000f:iis-servers.srvhdr[000c:000d]: Date: Mon, 12 Nov 2012 10:02:25 GMT 0000000e:iis-servers.srvcls[0008:0009] 0000000e:iis-servers.clicls[0008:0009] 0000000e:iis-servers.closed[0008:0009] 0000000f:iis-servers.srvcls[000c:000d] 0000000f:iis-servers.clicls[000c:000d] 0000000f:iis-servers.closed[000c:000d] 00000009:iis-servers.srvcls[000a:000b] 00000009:iis-servers.clicls[000a:000b] 00000009:iis-servers.closed[000a:000b] Where in the chain is the issue here?

  Read the article

• git push problem -argh!

  - by phil swenson

  Dunno what's going on, no response from github on this prob so I'm asking here. Tried a git push for the first time in a month or so and got this. Turned on export GIT_CURL_VERBOSE=1 and did a push and get this: localhost:send2mobile_rails phil$ git push Password: * Couldn't find host github.com in the .netrc file; using defaults * About to connect() to github.com port 443 (#0) * Trying 207.97.227.239... * Connected to github.com (207.97.227.239) port 443 (#0) * SSL connection using DHE-RSA-AES256-SHA * Server certificate: * subject: O=*.github.com; OU=Domain Control Validated; CN=*.github.com * start date: 2009-12-11 05:02:36 GMT * expire date: 2014-12-11 05:02:36 GMT * subjectAltName: github.com matched * issuer: C=US; ST=Arizona; L=Scottsdale; O=GoDaddy.com, Inc.; OU=http://certificates.godaddy.com/repository; CN=Go Daddy Secure Certification Authority; serialNumber=07969287 * SSL certificate verify ok. > GET /303devworks/send2mobile_rails.git/info/refs?service=git-receive-pack HTTP/1.1 User-Agent: git/1.7.1 Host: github.com Accept: */* Pragma: no-cache < HTTP/1.1 401 Authorization Required < Server: nginx/0.7.61 < Date: Tue, 01 Jun 2010 10:53:13 GMT < Content-Type: text/html; charset=iso-8859-1 < Connection: keep-alive < Content-Length: 0 < WWW-Authenticate: Basic realm="Repository" < * Connection #0 to host github.com left intact * Issue another request to this URL: 'https://[email protected]/MYUSERHERE/send2mobile_rails.git/info/refs?service=git-receive-pack' * Couldn't find host github.com in the .netrc file; using defaults * Re-using existing connection! (#0) with host github.com * Connected to github.com (207.97.227.239) port 443 (#0) * Server auth using Basic with user '303devworks' > GET /303devworks/send2mobile_rails.git/info/refs?service=git-receive-pack HTTP/1.1 Authorization: Basic MzAzZGVfd29sa3M6Y29nbmwzNzIw User-Agent: git/1.7.1 Host: github.com Accept: */* Pragma: no-cache < HTTP/1.1 200 OK < Server: nginx/0.7.61 < Date: Tue, 01 Jun 2010 10:53:13 GMT < Content-Type: application/x-git-receive-pack-advertisement < Connection: keep-alive < Status: 200 OK < Pragma: no-cache < Content-Length: 153 < Expires: Fri, 01 Jan 1980 00:00:00 GMT < Cache-Control: no-cache, max-age=0, must-revalidate < * Expire cleared * Connection #0 to host github.com left intact Counting objects: 166, done. Delta compression using up to 4 threads. Compressing objects: 100% (133/133), done. * Couldn't find host github.com in the .netrc file; using defaults * About to connect() to github.com port 443 (#0) * Trying 207.97.227.239... * connected * Connected to github.com (207.97.227.239) port 443 (#0) * SSL re-using session ID * SSL connection using DHE-RSA-AES256-SHA * old SSL session ID is stale, removing * Server certificate: * subject: O=*.github.com; OU=Domain Control Validated; CN=*.github.com * start date: 2009-12-11 05:02:36 GMT * expire date: 2014-12-11 05:02:36 GMT * subjectAltName: github.com matched * issuer: C=US; ST=Arizona; L=Scottsdale; O=GoDaddy.com, Inc.; OU=http://certificates.godaddy.com/repository; CN=Go Daddy Secure Certification Authority; serialNumber=07969287 * SSL certificate verify ok. * Server auth using Basic with user 'MYUSERHERE' > POST /303devworks/send2mobile_rails.git/git-receive-pack HTTP/1.1 Authorization: Basic JzAzZGV1d29ya3M6Y25nb29zNzIq User-Agent: git/1.7.1 Host: github.com Accept-Encoding: deflate, gzip Content-Type: application/x-git-receive-pack-request Accept: application/x-git-receive-pack-result Expect: 100-continue Transfer-Encoding: chunked * The requested URL returned error: 411 * Closing connection #0 error: RPC failed; result=22, HTTP code = 411 Writing objects: 100% (140/140), 2.28 MiB | 1.93 MiB/s, done. Total 140 (delta 24), reused 0 (delta 0) ^C localhost:send2mobile_rails phil$

  Read the article

• git checkout master/branching question

  - by danwoods

  Hello all, I 'm relatively new to git and and having some problems early on. I've made several commits, but when I try to push them I get a response that says everything is up-to-date. I feel like my problem is the same on listed in this question, but it recommends the following: $ git log -1 # note the SHA-1 of latest commit $ git checkout master # reset your branch head to your previously detached commit $ git reset --hard <commit-id> What exactly will "checking out the master" do? I just don't want to lose the changes I've made... screenshot of gitk:

  Read the article

• Git exclude a commit in a branch

  - by becomingGuru

  I have a commit, I have stored in a branch, because this should go only to a specific box. I have merged it to the branch master, but not the branch dev, that I use locally. Now, by mistake I merged master to dev and that introduced this commit to dev. I know can git revert sha, to branch dev; but since this is going to introduce a commit that undoes that commit (I am guessing, I haven't exactly tried this), when I merge master, will this commit be undone too? If so, how do I undo this commit only from the branch dev. And oh, git reset HEAD^1 --hard is not an option because there are other commits on master, after the un-needed commit. If reset back again and apply is the only option, then how do I only merge those extra commits from master other than the un-needed commit. Thanks in advance!

  Read the article

< Previous Page | 50 51 52 53 54 55 56 57 58 59 60 61  | Next Page >