Search Results

Search found 20946 results on 838 pages for 'at command'.

Page 543/838 | < Previous Page | 539 540 541 542 543 544 545 546 547 548 549 550  | Next Page >

  • OpenBSD ftp-proxy behind NAT itself

    - by Manuel Faux
    Is it possible to change the PASV IP ftp-proxy of OpenBSD sends to clients, without changing the listen address of redirection control (-b <address>)? I have the following setup: FTP client --> 1:1 NAT router --> OpenBSD router --> FTP server The 1:1 NAT router has a NAT rule to forward everything to the OpenBSD router, the OpenBSD router runs the ftp-proxy -R <FTP server IP>. When the FTP client sends the PASV command, the proxy answers with the Entering Passive Mode (227) message with his own source IP on the interface to the 1:1 NAT router (obviously). Since the 1:1 NAT router is not protocol aware, it forwards this message and the client receives the message with the PASV IP of the OpenBSD router, which it does not have a route to. Is there a way, that I can tell ftp-proxy to send the Entering Passive Mode message with a different source IP?

    Read the article

  • How to set up wireless access on a Cisco router

    - by Carlos
    Hi, I've set up my 877W according to the configuration listed in this forum post: IPTV over Cisco 877 (It's the working configuration at the bottom of the post) Note that I have an 877W, so it also has a wireless radio. Now, I've gotten the whole setup to work, so IPTV is working, and I can access the internet via the ethernet ports. Now I'm trying to figure out how to allow access via the dot11radio interface. I've gathered that I basically need to create a bridge group, and bridge the radio to the internet VLAN. However, when I add a bridge-group 2 command to VLAN1, it seems to take down the whole internet VLAN. (The IPTV continues to work.) This makes the router itself inaccessible (I've got a laptop, so no serial) and I end up having to reboot the router. Can anyone tell me how to a) Allow wireless access to the internet (preferably with WEP, to match my old router) b) Determine what makes the router inaccessible when I add the new bridge group c) Forward the IPTV traffic onto a machine on my internet VLAN

    Read the article

  • CodePlex Daily Summary for Monday, October 08, 2012

    CodePlex Daily Summary for Monday, October 08, 2012Popular ReleasesSofire Suite v1.6: XSqlModelGenerator.AddIn: 1、?? VS2010/2012 2、?? .NET FRAMEWORK 2.0 3、?? SOFIRE V1.6Sofire XSql: XSqlFormDemo: ???? MSSQL ???????ClosedXML - The easy way to OpenXML: ClosedXML 0.68.0: ClosedXML now resolves formulas! Yes it finally happened. If you call cell.Value and it has a formula the library will try to evaluate the formula and give you the result. For example: var wb = new XLWorkbook(); var ws = wb.AddWorksheet("Sheet1"); ws.Cell("A1").SetValue(1).CellBelow().SetValue(1); ws.Cell("B1").SetValue(1).CellBelow().SetValue(1); ws.Cell("C1").FormulaA1 = "\"The total value is: \" & SUM(A1:B2)"; var...Picturethrill: Version 2.10.7.0: Major FeaturesWindows 8 Support!!! Picturethrill is fully tested on latest Windows 8. Try it now.New AboutPicturethrill Dialog Available from "Advanced" window. Describes Version, Developers and other infoFull Installation Information in Control Panel Picturethrill in ControlPanel has full information, including Version and Size. Minor Bug FixesImproved Logging AppDomain Unhandled Exception Logging Delete WallpaperDownload Folder (Saves Diskspace) Advanced Settings "Close" button bug ...VidCoder: 1.4.3 Beta: Fixed crash on switching container types. Updated subtitle selection to only allow one PGS subtitle to be selected under an MP4 container as PGS passthrough in MP4 is not supported and the sub must be burned in.Microsoft Ajax Minifier: Microsoft Ajax Minifier 4.68: Fixes for issues: 17110 - added support for -moz-calc or -webkit-calc to previous fix for calc support. 18652 - if being run under Mono runtime, don't mistake UNIX-style paths for command-line switches. 18659 - added capability to specify JS settings for CSS files that have JS embedded in expressions. Did a lot of internal house-keeping: add DLL support for -pponly switch. Add support for -js:expr, -js:evt, and -js:json to allow easy parsing for expressions, event handlers, and JSON code...Json.NET: Json.NET 4.5 Release 10: New feature - Added Portable build to NuGet package New feature - Added GetValue and TryGetValue with StringComparison to JObject Change - Improved duplicate object reference id error message Fix - Fixed error when comparing empty JObjects Fix - Fixed SecAnnotate warnings Fix - Fixed error when comparing DateTime JValue with a DateTimeOffset JValue Fix - Fixed serializer sometimes not using DateParseHandling setting Fix - Fixed error in JsonWriter.WriteToken when writing a DateT...Readable Passphrase Generator: KeePass Plugin 0.7.2: Changes: Tested against KeePass 2.20.1 Tested under Ubuntu 12.10 (and KeePass 2.20) Added GenerateAsUtf8 method returning the encrypted passphrase as a UTF8 byte array.JSLint for Visual Studio 2010: 1.4.2: 1.4.2GPdotNET - artificial intelligence tool: GPdotNET v2 BETA3: This is hopefully the last beta before final version.RiP-Ripper & PG-Ripper: PG-Ripper 1.4.02: changes NEW: Added Support Big Naturals Only forum NEW: Added Setting to enable/disable "Show last download image"patterns & practices: Prism: Prism for .NET 4.5: This is a release does not include any functionality changes over Prism 4.1 Desktop. These assemblies target .NET 4.5. These assemblies also were compiled against updated dependencies: Unity 3.0 and Common Service Locator (Portable Class Library).WinRT XAML Toolkit: WinRT XAML Toolkit - 1.3.2: WinRT XAML Toolkit based on the Windows 8 RTM SDK. Download the latest source from the SOURCE CODE page. For compiled version use NuGet. You can add it to your project in Visual Studio by going to View/Other Windows/Package Manager Console and entering: PM> Install-Package winrtxamltoolkit Features AsyncUI extensions Controls and control extensions Converters Debugging helpers Imaging IO helpers VisualTree helpers Samples Recent changes NOTE: Namespace changes DebugConsol...Snoop, the WPF Spy Utility: Snoop 2.8.0: Snoop 2.8.0Announcing Snoop 2.8.0! It's been exactly six months since the last release, and this one has a bunch of goodies in it. In particular, there is now a PowerShell scripting tab, compliments of Bailey Ling. With this tab, the possibilities are limitless. It basically lets you automate/script the application that you are Snooping. Bailey has a couple blog posts (one and two) on his tab already, and I am sure more is to come. Please note that if you do not have PowerShell installed, y....NET Micro Framework: .NET MF 4.3 (Beta): This is the 4.3 Beta version of the .NET Micro Framework. Feature List for v4.3 Support for Visual Studio 2012 (including the Windows Desktop Express version) All v4.2 QFEs features and bug fixes (PWM enhancements, lwIP and network driver reliability improvements, Analog Output, WinUSB and latest GCC support) Improved diagnostic information for deployment Decreased boot time Bug fixes Work Item 1736 - Create link for MFDeploy under start menu Work Item 1504 - Customizing lwIP o...MCEBuddy 2.x: MCEBuddy 2.3.1: 2.3.1All new Remote Client Server architecture. Reccomended Download. The Remote Client Installation is OPTIONAL, you can extract the files from the zip archive into a local folder and run MCEBuddy.GUI directly. 2.2.15 was the last standalone release. Changelog for 2.3.1 (32bit and 64bit) 1. All remote MCEBuddy Client Server architecture (GUI runs remotely/independently from engine now) 2. Fixed bug in Audio Offset 3. Added support for remote MediaInfo (right click on file in queue to get ...D3 Loot Tracker: 1.5: Support for session upload to website. Support for theme change through general settings. Time played counter will now also display a count for days. Tome of secrets are no longer logged as items.Team Foundation Server Word Add-in: Version 1.0.12.0622: Welcome to the Visual Studio Team Foundation Server Word Add-in Supported Environments Microsoft Office Word 2007 and 2010 X86 (32-bit) Team Foundation Server 2010 Object Model TFS 2010, 2012 and TFS Service supported, using TFS OM / Explorer 2010. Quality-Bar Details Tool has been reviewed by Visual Studio ALM Rangers Tool has been through an independent technical and quality review All critical bugs have been resolved Known Issues / Bugs WI#43553 - The Acceptance criteria is not pu...DirectX Tool Kit: October 2012: October 2, 2012 Added ScreenGrab module Added CreateGeoSphere for drawing a geodesic sphere Put DDSTextureLoader and WICTextureLoader into the DirectX C++ namespace Renamed project files for better naming consistency Updated WICTextureLoader for Windows 8 96bpp floating-point formats Win32 desktop projects updated to use Windows Vista (0x0600) rather than Windows 7 (0x0601) APIs Tweaked SpriteBatch.cpp to workaround ARM NEON compiler codegen bugCRM 2011 Visual Ribbon Editor: Visual Ribbon Editor (1.3.1002.3): Visual Ribbon Editor 1.3.1002.3 What's New: Multi-language support for Labels/Tooltips for custom buttons and groups Support for base language other than English (1033) Connect dialog will not require organization name for ADFS / IFD connections Automatic creation of missing labels for all provisioned languages Minor connection issues fixed Notes: Before saving the ribbon to CRM server, editor will check Ribbon XML for any missing <Title> elements inside existing <LocLabel> elements...New Projectsamplifi: This project is still under construction. We will add more information here as soon as it is available.autoclubpigue: Proyecto para el auto club de piguecoiffeurprj: coiffeurprjerutufym: erutufym is gnol eht gge.Express AOP: A .NET AOP ToolsFile Slurpee: The purpouse of this application is to help security professionals during their penetration tests. Given a configuration this application will scour the target Guardian - Google Authenticator: Guardian is a windows client application for Google Authenticator - a software based two-factor authentication token developed by Google.ManagedCuda Galaxy Simulator: This project is a test of ManagedCuda and graphics interop to OpenTK to simulate a simple galaxy on the GPU.mostafanote: ????? ???? ??????? ?? ???? ?? ?? ?? ? ?? ??????? ?? ??????? ??? ?? ??? ?? ?? ???????? ??????? ??? ??? ?? ???? ?????? NXT Controller: A simple controller for the LEGO Mindstorms NXTPowerShell Security: PoshSec is short for PowerShell security, a module provided to allow PowerShell users testing, analysis and reporting on Window securityRevenant Raiders - Sunstrider: Tool to provide information about Revenant Raiders - Sunstrider.Run: animal runSharedDeploy: Simple ASP.MVC app , that use 2 types of view : mobile and desktop. In core WebApi, jQuery, jQuery.mobileSkyCoffee: Cafeteria ApplicationSOSA Analysis Module: Analysis program for data from SOSA psychological experiment software.SQL Connector: SQL Connector is a .DLL file that make it easy to comunicate with SQL Server Works in : Windows Desktop Applications ASP.Net Web (MVC - WEB Services) Windows cSQL Job Scripter: SQL Job Scripter is a command line utility that produces scripts of SQL Agent jobs. It will script either to a single file or to one file per job. SQL Server Watcher: A tool for collecting and monitoring information about sql server.Team Build Inspector: An add-in for Visual Studio Team Explorer that monitors the status of build definitions by its latest build, latest good build & underlying source code status.TED Talk Download Manager: "TED Talk Download Manager" provides a central point in which to download multiple TED talks, while keeping track of any talk previously downloaded.Temp project mycollection: My collection temporary projectUnreal Unit Converter: A Simple UDK <-> 3DS Max <-> Meters Unit Converter - with some other stuff.Watermelon Site: This Site is The site of Watermelon Inc. In This Site: Downloads News about Watermelon And more... WiX Extended Bootstrapper Application: An extended WiX bootstrapper Application based on the WiX standard bootstrapper application.Wrox NHibernate with ASP.NET Problem-Design-Solution -C# version: sample code of Wrox NHibernate with ASP.NET Problem-Design-Solution (http://nhibernateasp.codeplex.com/) in C# which is done as a practice

    Read the article

  • Cannot login to XP SP3 in VMWarePlayer virtual machine in safe mode

    - by Alper
    Hello, Here is my setup Host OS: XP SP3 Guest OS: XP SP3 (using VMWare) I checked the /SAFEBOOT option in System Config utility in guest for troubleshooting. Now the guest OS boots up in Safe Mode but I cannot login with my user id/password. Here is what I tried: [domainName]\[userid] for user name = Login Fails Administrator with blank password = Login fails Safe Mode with Networking = Login fails Safe Mode with Command Prompt = Login fails Last Known Good Configuration = starts in safe mode, login fails Start Windows Normally = starts in safe mode, login fails Don't have cd to get to the recovery console Any ideas?

    Read the article

  • My Visual Studio Demo Video Link disappeared &ndash; How do I get it back?

    - by Tarun Arora
    ***Special thanks to Adam Cogan for asking this question and to Andrew Bragdon for answering this question on the ALM Champs list.*** 1. Problem – The link to demo videos will disappear once you have watched the video Learning Visual Studio has become easier than ever with the Visual Studio How to Videos hosted inside of Visual Studio showing up in the context of the task you are trying to achieve. For instance when you click code review in team explorer you can see the link “Streaming Video: Using Code Review to improve quality” when you click this link the video stream is delivered to you right with in Visual Studio. Next time you run Visual Studio you will notice that the home page has a check mark in the video “Using Code Review to improve quality”. If you navigate to code review in the myWork hub in the team explorer, you will notice that the link “Streaming Video: Using Code Review to improve quality” does not show up any more.         2. Solution – How to get the Demo Videos link back Warning: Editing the registry can lead to serious problems if not done correctly.  Always backup your registry before editing. This solution is neither suggested nor supported by Microsoft. Type regedit on the run command prompt to open the Registry editor Navigate to the path Computer\HKEY_CURRENT_USER\Software\Microsoft\VisualStudio\11.0\UltimateStartPage\VideoState and notice the newly created folder “TeamExplorer.CodeReview”, notice the key Watched is set to 1.         Change the value of the key ‘Watched’ to 0 Restart Visual Studio and Navigate to Code Review in myWork hub and voila, the link to stream the video is back!            Watch and enjoy the Demo videos to your hearts content!

    Read the article

  • Slight delay when switching modes in vim using tmux or screen

    - by Ton van den Heuvel
    Switching to and from insert mode in Vim is no longer instantaneous since I use tmux. After pressing Esc in insert mode, it takes a noticeable amount of time to actually get out of insert mode. After pressing Esc and any other key afterwards the switch is immediate, and the command for the key pressed after Esc is executed. Any idea what might cause this? The Vim configuration is not the problem as the delay does not occur when I run Vim outside tmux, so this is probably related to tmux somehow. I use gnome-terminal btw. Also worth noting, it seems I can not define key bindings in tmux for Esc, my plan was to bind Esc to: bind Escape send-keys ^[ Alas, it seems binding anything to Esc for tmux does not work. The same problem occurs in screen as well.

    Read the article

  • Local file system not properly unmounted during shutdown

    - by bernhard
    I have a file system with two HDDs and several partitions mounted separately locally. /root, /home, /usr, /var, /local/share , /home/bernhard/fotos/bilder, /backup are on separate partitions and are all ext3. During unmounting the message "unmounting local file system" does not appear any further and when booting all partitions but the root partition have to reload the journal, which indicates improper unmounting. The root partition and /usr are on sda, the others on sdb or further usb-mounted devices. the only partition unmounted w/o problem seems to be the root partition on sda4. I wonder whether the script to umount all devices has a "wait for success" loop or that the script itself got corrupted. However, yesterday I upgraded to 11.04 and the error persists. pmount does not look to be appropriate since the device are not hotplugged but simply mounted during system start. Obviously mounting /usr and afterwards /usr/local/share as well as /home and later /home/bernhard/fotos/bilder presents problems for umount; the devices may be busy und thus not properly unmounted. Does anybody have an idea for a script to organize unmounting in an ordered way? How to wait for unmounting of the secondary mount? Do you know as well where to place such a script that it will be used instead of the original umount command? Could be a general solution.

    Read the article

  • Application Launcher for Hyper-V Server

    - by peterchen
    We are currently in the process of setting up a HyperV R2 Server machine. Though there's not a lot we need to do wihtin the HyperV Server itself, the command line is sure minimalistic. There are a few administrative / Hardware Monitoring tools that we want to run on he machine itself (accessed through remote desktop). I am looking for a simple program/application launcher where we can hook up these maintenance tools (and one to open a new cmd.exe window in case I habitually close the one I'm working in!) However, all tools I tried by now more or less assume explorer is present, and fail in different ways. Before I go and write a simple one myself, any recommendations?

    Read the article

  • decrypting AES files in an apache module?

    - by Tom H
    I have a client with a security policy compliance requirement to encrypt certain files on disk. The obvious way to do this is with Device-mapper and an AES crypto module However the current system is setup to generate individual files that are encrypted. What are my options for decrypting files on-the-fly in apache? I see that mod_ssl and mod_session_crypto do encryption/decryption or something similar but not exactly what I am after. I could imagine that a PerlSetOutputFilter would work with a suitable Perl script configured, and I also see mod_ext_filter so I could just fork a unix command and decrypt the file, but they both feel like a hack. I am kind of surprised that there is no mod_crypto available...or am I missing something obvious here? Presumably resource-wise the perl filter is the way to go?

    Read the article

  • How can I limit the upload/download bandwidth on my CentOS server?

    - by Dan Nestor
    How can I limit the upload and download bandwidth on my CentOS server? This is a box with a single interface, eth0. Ideally, I would like a command-line solution (I've been trying to use tc), something that I could easily switch on and off in a script. So far I've been trying to do something like tc filter add dev eth0 protocol ip prio 50 u32 police rate 100kbit burst 10240 drop but I'm obviously missing a lot of knowledge and information. Can somebody help with a quick one-liner? Many thanks, Dan

    Read the article

  • Unable to load memcache.so extension ??

    - by billyduc
    I built php from source with configure command : './configure' '--prefix=/usr/local/php-5.2.8' '--with-config-file-path=/etc --with-config-file-scan-dir=/etc/php.d' '--with-apxs2=/usr/local/httpd/bin/apxs' '--with-mysql=/usr/local/mysql/' '--with-zlib' I installed php memcache extension : wget http://pecl.php.net/get/memcache tar -zxvf memcache-2.2.5.tgz cd memcache-2.2.5 phpize ./configure --enable-memcache make make install I add to my /usr/local/lib/php.in extension=memcache.so Rebooted my apache and run php-m but php seem doesn't load memcache extension I followed this solution from this site http://www.howtoforge.com/forums/showthread.php?t=26554 I added full path extension=/usr/local/lib/php/extensions/no-debug-non-zts-20060613/memcache.so rebooted apache But it didn't load memcache extension ! I google around but the same issue ! How can I load this extension _ _"

    Read the article

  • OS Missing? Messed up the MBR on Win7 64-bit

    - by hom3lesshom3boy
    I have a Windows 7 machine with two hard drives: a 1TB C: drive and 500GB J:. I had Windows XP installed on C: and Windows 7 installed on J:. I installed Windows 7 after Windows XP from an installer .exe I (legally) bought and downloaded. It, and all of my other files, are sitting on my J: drive intact. While under my Windows 7 install, a few days ago I decided to use Priform's CCleaner and use its DriveWipe utility to wipe the C: drive. 1% into the process, I cancelled and attempted to use it again. It gives me an error saying it can't format the drive, so I poke around the Internet a bit, give up, and restart my computer. I first get an "OS is missing" error after the computer boots past the BIOS. I downloaded and put UBCD on a bootable USB to use another drivewiping tool to completely erase the C: drive, hoping it'll take the problem with it. No luck. I try to use TestDisk to make my J: my primary active drive, but no luck. I still get the "OS is missing" error. Or sometimes it'll hang at Verifying DMI Pool. Or sometimes I'll get the "NTLDR is missing" error. I get hold of Hiren's and put it on another bootable USB. I first I tried the Boot Windows 7 from Hard Drive option, and I get "Error 15: File Not Found". I tried the "Fix 'NTLDR is Missing'" option (I'm not quite sure why this is even showing up, since I'm trying to get into a HDD with Windows 7 installed. Probably messed up somewhere when I used TestDisk) and I get this list: I'll run through the error messages I get: 1st Try - Windows could not start because the following file is missing or corrupt: \system32\hal.dll 2nd Try - Windows could not start because the following file is missing or corrupt: \system32\ntoskrnl.exe 3rd Try - Windows could not start because of a computer disk hardware configuration problem. Could not read from the selected boot disk. Check boot path and disk hardware. 4th - 8th Try - Same as #3 9th Try - I/O Error accessing boot sector file multi(0)disk(0)fdisk(0)\BOOTSEC.DOS. And computer freezes. 10th Try - computer restarts Needless to say, not a single one of those works. I then tried to open up the Windows 7 exe I have sitting on my J: from the Mini-XP OS on Hiren's, but it won't run because I'm trying to run a 64-bit file from a 32-bit exe. At least, that's the problem according to these guys: http://social.technet.microsoft.com/...-b2f54e9c7d18/ I then borrowed a 64-bit Windows Home Premium CD from a friend to get to the recovery options. But I get the error message: This version of System Recovery Options is not compatible with the version of Windows you are trying to repair. Try using a recovery disc that is compatible with this version of Windows. I pressed Shift + F10 to get to the Command Prompt directly. These are the exact steps I took from there (paraphrased a little): X:\Sources>bootrec /Fixmbr The operation completed successfully. X:\Sources>bootrec /Fixboot The operation completed successfully. I restarted my computer, but it still didn't work. I unplugged the C: drive, then tried bootrec and Diskpart: X:\Sources> bootrec.exe X:\Sources> bootrec /RebuildBcd Total identified Windows installations: 1 [1] \\?\GLOBALROOT\Device\HarddiskVolume1\Windows Add installation to bootlist? Yes(Y)/No(N)/All(A):y The requested system device cannot be found. X:\Sources>DiskPart DISKPART> List Disk Disk # Status Size Free Dyn Gpt Disk 0_Online_465GB_0B_______* Disk 1 Online 1000MB 0B (this is Hiren's on a bootable usb) DISKPART> Select Disk 0 Disk 0 is now the selected disk. DISKPART> List Partition Partition # Type Size Offset Partition 1 System 465GB 31KB DISKPART> Select Partition 1 Partition 1 is now the selected partition DISKPART> Active The selected disk is not a fixed MBR disk. The ACTIVE command can only be used on fixed MBR disks. DISKPART> exit Leaving Diskpart... X:\Sources>bootrec /Fixmbr The operation completed successfully. X:\Sources>bootrec /Fixboot The operation completed successfully. Before I go any further, is there anything I'm overlooking/doing wrong? All I care about is making the J: and Windows 7 bootable again. SPECS: Windows 7 Professional 64-Bit GIGABYTE - Motherboard - Socket 775 - GA-P35-DS3R (rev. 2.1) Crucial Ballistix 2048MB PC6400 DDR2 800MHz (2x2GB) Intel Core 2 Duo E6700 Processor (2.6 (6GHZ) I think... not sure anymore C: HDD - SAMSUNG HD103UJ (1TB, not plugged in) J: HDD - WDC WD5000AKS-00V1A0 (500GB)

    Read the article

  • Access Methods to a computer Using MAC Address

    - by Dimal Chandrasiri
    I have my own wifi network at home & recently when I checked the active clients on the wifi I found out the there is one active client. Router shows the MAC address of this client and I want to Access this computer in order to let him know that he's doing a wrong thing. I dont intent to do any harm to his data. I just want to know a method to send him a message saying "Buy you own wifi". How can I achieve this using a windows 8 computer. Is there any specific softwares that I can use or will the netsend command do the trick! Thank you.

    Read the article

  • Sensitive data in init scripts

    - by Steve Jorgensen
    I'm adapting some examples I've found by Googling to build an init script to run a VirtualBox OSE virtual machine as a daemon. I would like to specify a password for VNC access to the VM, and this must be given as an argument to the VBoxHeadless command. Conventionally, init scripts are readable by standard users, and this seems like a useful convention, but I also don't want the VNC password for this VM to be stored in easily accessible plain text. What's the most appropriate/conventional way to handle this kind of situation? Maybe put a root-readable supporting data file someplace, and have the init script load the value from there?

    Read the article

  • How to generate a 8 bit per sample wav audio file in VLC

    - by Ahmed safan
    I'm using the following vlc command line to extract first 5 minutes of audio from video file "-I dummy -vvv --no-sout-video --sout-audio --no-sout-rtp-sap --no-sout-standard-sap --ttl=1 --sout-transcode-threads=5 --sout-transcode-high-priority --sout-keep --sout #transcode{acodec=s16l,channels=1,samplerate=8000,ab=64}:std{mux=wav,access=file,dst="c:\dest.wav"} "c:\originalvideo.mpg" --start-time=0 --stop-time=300 vlc://quit"; if ab=64 =64 k bits per second and samples per second=8 k samples then bits per sample=64/8=8 bits per sample but the problem is that the output file always has samples of 16 bits per sample. I know that sample can contain bits from 8 , 16, 24 to 32 bits per sample. i want to get 8 bits per sample file how can this be done ?

    Read the article

  • cant access site intermittent as i get site not available

    - by user61438
    i have a news site i check stuff for regularly.. once in a while i cant access it completely from my 5 different browsers and even from the command line, nslookup cant resolve, ping and tracert fails.. all not being able to resolve site name..the problem is specific to this.. i am told by the site support person that problem is that its cache on my machine or on ISP and I say thats not true because this site I access it 1-2-3 times a week from one browser only.. i only fire up the other ones in times of trouble..and when i have the problem even if i try on my secondary machines i still get the same problems.. when problem goes away all works well.... question is whats causing the intermittent dns/http problems... i don't believe this is something to do with my machine because probe disappears without me having done anything at all.

    Read the article

  • Too many sleeping processes?

    - by user55859
    I'm running Debian Lenny (x86_64) on a cloud VPS (Xen) and top command tells me there are 210 processes running and 209 are sleeping: top - 14:49:29 up 15:18, 1 user, load average: 0.09, 0.11, 0.05 Tasks: 210 total, 1 running, 209 sleeping, 0 stopped, 0 zombie Cpu(s): 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 532288k total, 437316k used, 94972k free, 30584k buffers Swap: 1048568k total, 408k used, 1048160k free, 219772k cached And here is what ps aux command gives me: USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 1 0.0 0.1 10380 812 ? Ss Sep30 0:00 init [2] root 2 0.0 0.0 0 0 ? S< Sep30 0:00 [kthreadd] root 3 0.0 0.0 0 0 ? S< Sep30 0:00 [migration/0] root 4 0.0 0.0 0 0 ? S< Sep30 0:00 [ksoftirqd/0] root 5 0.0 0.0 0 0 ? S< Sep30 0:00 [events/0] root 6 0.0 0.0 0 0 ? S< Sep30 0:00 [khelper] root 7 0.0 0.0 0 0 ? S< Sep30 0:05 [xenwatch] root 8 0.0 0.0 0 0 ? S< Sep30 0:13 [xenbus] root 10 0.0 0.0 0 0 ? S< Sep30 0:00 [migration/1] root 11 0.0 0.0 0 0 ? S< Sep30 0:00 [ksoftirqd/1] root 12 0.0 0.0 0 0 ? S< Sep30 0:00 [events/1] root 13 0.0 0.0 0 0 ? S< Sep30 0:00 [migration/2] root 14 0.0 0.0 0 0 ? S< Sep30 0:00 [ksoftirqd/2] root 15 0.0 0.0 0 0 ? S< Sep30 0:00 [events/2] root 16 0.0 0.0 0 0 ? S< Sep30 0:00 [migration/3] root 17 0.0 0.0 0 0 ? S< Sep30 0:00 [ksoftirqd/3] root 18 0.0 0.0 0 0 ? S< Sep30 0:00 [events/3] root 19 0.0 0.0 0 0 ? S< Sep30 0:00 [migration/4] root 20 0.0 0.0 0 0 ? S< Sep30 0:00 [ksoftirqd/4] root 21 0.0 0.0 0 0 ? S< Sep30 0:00 [events/4] root 22 0.0 0.0 0 0 ? S< Sep30 0:00 [migration/5] root 23 0.0 0.0 0 0 ? S< Sep30 0:00 [ksoftirqd/5] root 24 0.0 0.0 0 0 ? S< Sep30 0:00 [events/5] root 25 0.0 0.0 0 0 ? S< Sep30 0:00 [migration/6] root 26 0.0 0.0 0 0 ? S< Sep30 0:00 [ksoftirqd/6] root 27 0.0 0.0 0 0 ? S< Sep30 0:00 [events/6] root 28 0.0 0.0 0 0 ? S< Sep30 0:00 [migration/7] root 29 0.0 0.0 0 0 ? S< Sep30 0:00 [ksoftirqd/7] root 30 0.0 0.0 0 0 ? S< Sep30 0:00 [events/7] root 31 0.0 0.0 0 0 ? S< Sep30 0:00 [migration/8] root 32 0.0 0.0 0 0 ? S< Sep30 0:00 [ksoftirqd/8] root 33 0.0 0.0 0 0 ? S< Sep30 0:00 [events/8] root 34 0.0 0.0 0 0 ? S< Sep30 0:00 [migration/9] root 35 0.0 0.0 0 0 ? S< Sep30 0:00 [ksoftirqd/9] root 36 0.0 0.0 0 0 ? S< Sep30 0:00 [events/9] root 37 0.0 0.0 0 0 ? S< Sep30 0:00 [migration/10] root 38 0.0 0.0 0 0 ? S< Sep30 0:00 [ksoftirqd/10] root 39 0.0 0.0 0 0 ? S< Sep30 0:04 [events/10] root 40 0.0 0.0 0 0 ? S< Sep30 0:00 [migration/11] root 41 0.0 0.0 0 0 ? S< Sep30 0:00 [ksoftirqd/11] root 42 0.0 0.0 0 0 ? S< Sep30 0:00 [events/11] root 43 0.0 0.0 0 0 ? S< Sep30 0:00 [migration/12] root 44 0.0 0.0 0 0 ? S< Sep30 0:00 [ksoftirqd/12] root 45 0.0 0.0 0 0 ? S< Sep30 0:00 [events/12] root 46 0.0 0.0 0 0 ? S< Sep30 0:00 [migration/13] root 47 0.0 0.0 0 0 ? S< Sep30 0:00 [ksoftirqd/13] root 48 0.0 0.0 0 0 ? S< Sep30 0:00 [events/13] root 49 0.0 0.0 0 0 ? S< Sep30 0:00 [migration/14] root 50 0.0 0.0 0 0 ? S< Sep30 0:00 [ksoftirqd/14] root 51 0.0 0.0 0 0 ? S< Sep30 0:00 [events/14] root 52 0.0 0.0 0 0 ? S< Sep30 0:00 [migration/15] root 53 0.0 0.0 0 0 ? S< Sep30 0:00 [ksoftirqd/15] root 54 0.0 0.0 0 0 ? S< Sep30 0:00 [events/15] root 55 0.0 0.0 0 0 ? S< Sep30 0:00 [kintegrityd/0] root 56 0.0 0.0 0 0 ? S< Sep30 0:00 [kintegrityd/1] root 57 0.0 0.0 0 0 ? S< Sep30 0:00 [kintegrityd/2] root 58 0.0 0.0 0 0 ? S< Sep30 0:00 [kintegrityd/3] root 59 0.0 0.0 0 0 ? S< Sep30 0:00 [kintegrityd/4] root 60 0.0 0.0 0 0 ? S< Sep30 0:00 [kintegrityd/5] root 61 0.0 0.0 0 0 ? S< Sep30 0:00 [kintegrityd/6] root 62 0.0 0.0 0 0 ? S< Sep30 0:00 [kintegrityd/7] root 63 0.0 0.0 0 0 ? S< Sep30 0:00 [kintegrityd/8] root 64 0.0 0.0 0 0 ? S< Sep30 0:00 [kintegrityd/9] root 65 0.0 0.0 0 0 ? S< Sep30 0:00 [kintegrityd/10] root 66 0.0 0.0 0 0 ? S< Sep30 0:00 [kintegrityd/11] root 67 0.0 0.0 0 0 ? S< Sep30 0:00 [kintegrityd/12] root 68 0.0 0.0 0 0 ? S< Sep30 0:00 [kintegrityd/13] root 69 0.0 0.0 0 0 ? S< Sep30 0:00 [kintegrityd/14] root 70 0.0 0.0 0 0 ? S< Sep30 0:00 [kintegrityd/15] root 71 0.0 0.0 0 0 ? S< Sep30 0:00 [kblockd/0] root 72 0.0 0.0 0 0 ? S< Sep30 0:00 [kblockd/1] root 73 0.0 0.0 0 0 ? S< Sep30 0:00 [kblockd/2] root 74 0.0 0.0 0 0 ? S< Sep30 0:00 [kblockd/3] root 75 0.0 0.0 0 0 ? S< Sep30 0:00 [kblockd/4] root 76 0.0 0.0 0 0 ? S< Sep30 0:00 [kblockd/5] root 77 0.0 0.0 0 0 ? S< Sep30 0:00 [kblockd/6] root 78 0.0 0.0 0 0 ? S< Sep30 0:00 [kblockd/7] root 79 0.0 0.0 0 0 ? S< Sep30 0:00 [kblockd/8] root 80 0.0 0.0 0 0 ? S< Sep30 0:00 [kblockd/9] root 81 0.0 0.0 0 0 ? S< Sep30 0:00 [kblockd/10] root 82 0.0 0.0 0 0 ? S< Sep30 0:00 [kblockd/11] root 83 0.0 0.0 0 0 ? S< Sep30 0:00 [kblockd/12] root 84 0.0 0.0 0 0 ? S< Sep30 0:00 [kblockd/13] root 85 0.0 0.0 0 0 ? S< Sep30 0:00 [kblockd/14] root 86 0.0 0.0 0 0 ? S< Sep30 0:00 [kblockd/15] root 87 0.0 0.0 0 0 ? S< Sep30 0:00 [cqueue] root 88 0.0 0.0 0 0 ? S< Sep30 0:00 [kseriod] root 89 0.0 0.0 0 0 ? S Sep30 0:00 [pdflush] root 90 0.0 0.0 0 0 ? S Sep30 0:00 [pdflush] root 91 0.0 0.0 0 0 ? S< Sep30 0:00 [kswapd0] root 92 0.0 0.0 0 0 ? S< Sep30 0:00 [aio/0] root 93 0.0 0.0 0 0 ? S< Sep30 0:00 [aio/1] root 94 0.0 0.0 0 0 ? S< Sep30 0:00 [aio/2] root 95 0.0 0.0 0 0 ? S< Sep30 0:00 [aio/3] root 96 0.0 0.0 0 0 ? S< Sep30 0:00 [aio/4] root 97 0.0 0.0 0 0 ? S< Sep30 0:00 [aio/5] root 98 0.0 0.0 0 0 ? S< Sep30 0:00 [aio/6] root 99 0.0 0.0 0 0 ? S< Sep30 0:00 [aio/7] root 100 0.0 0.0 0 0 ? S< Sep30 0:00 [aio/8] root 101 0.0 0.0 0 0 ? S< Sep30 0:00 [aio/9] root 102 0.0 0.0 0 0 ? S< Sep30 0:00 [aio/10] root 103 0.0 0.0 0 0 ? S< Sep30 0:00 [aio/11] root 104 0.0 0.0 0 0 ? S< Sep30 0:00 [aio/12] root 105 0.0 0.0 0 0 ? S< Sep30 0:00 [aio/13] root 106 0.0 0.0 0 0 ? S< Sep30 0:00 [aio/14] root 107 0.0 0.0 0 0 ? S< Sep30 0:00 [aio/15] root 108 0.0 0.0 0 0 ? S< Sep30 0:00 [kpsmoused] root 167 0.0 0.0 0 0 ? S< Sep30 0:00 [net_accel/0] root 168 0.0 0.0 0 0 ? S< Sep30 0:00 [net_accel/1] root 169 0.0 0.0 0 0 ? S< Sep30 0:00 [net_accel/2] root 170 0.0 0.0 0 0 ? S< Sep30 0:00 [net_accel/3] root 171 0.0 0.0 0 0 ? S< Sep30 0:00 [net_accel/4] root 172 0.0 0.0 0 0 ? S< Sep30 0:00 [net_accel/5] root 173 0.0 0.0 0 0 ? S< Sep30 0:00 [net_accel/6] root 174 0.0 0.0 0 0 ? S< Sep30 0:00 [net_accel/7] root 175 0.0 0.0 0 0 ? S< Sep30 0:00 [net_accel/8] root 176 0.0 0.0 0 0 ? S< Sep30 0:00 [net_accel/9] root 177 0.0 0.0 0 0 ? S< Sep30 0:00 [net_accel/10] root 178 0.0 0.0 0 0 ? S< Sep30 0:00 [net_accel/11] root 179 0.0 0.0 0 0 ? S< Sep30 0:00 [net_accel/12] root 180 0.0 0.0 0 0 ? S< Sep30 0:00 [net_accel/13] root 181 0.0 0.0 0 0 ? S< Sep30 0:00 [net_accel/14] root 182 0.0 0.0 0 0 ? S< Sep30 0:00 [net_accel/15] root 315 0.0 0.0 0 0 ? S< Sep30 0:00 [xfs_mru_cache] root 316 0.0 0.0 0 0 ? S< Sep30 0:00 [xfslogd/0] root 317 0.0 0.0 0 0 ? S< Sep30 0:00 [xfslogd/1] root 318 0.0 0.0 0 0 ? S< Sep30 0:00 [xfslogd/2] root 319 0.0 0.0 0 0 ? S< Sep30 0:00 [xfslogd/3] root 320 0.0 0.0 0 0 ? S< Sep30 0:00 [xfslogd/4] root 321 0.0 0.0 0 0 ? S< Sep30 0:00 [xfslogd/5] root 322 0.0 0.0 0 0 ? S< Sep30 0:00 [xfslogd/6] root 323 0.0 0.0 0 0 ? S< Sep30 0:00 [xfslogd/7] root 324 0.0 0.0 0 0 ? S< Sep30 0:00 [xfslogd/8] root 325 0.0 0.0 0 0 ? S< Sep30 0:00 [xfslogd/9] root 326 0.0 0.0 0 0 ? S< Sep30 0:00 [xfslogd/10] root 327 0.0 0.0 0 0 ? S< Sep30 0:00 [xfslogd/11] root 328 0.0 0.0 0 0 ? S< Sep30 0:00 [xfslogd/12] root 329 0.0 0.0 0 0 ? S< Sep30 0:00 [xfslogd/13] root 330 0.0 0.0 0 0 ? S< Sep30 0:00 [xfslogd/14] root 331 0.0 0.0 0 0 ? S< Sep30 0:00 [xfslogd/15] root 332 0.0 0.0 0 0 ? S< Sep30 0:00 [xfsdatad/0] root 333 0.0 0.0 0 0 ? S< Sep30 0:00 [xfsdatad/1] root 334 0.0 0.0 0 0 ? S< Sep30 0:00 [xfsdatad/2] root 335 0.0 0.0 0 0 ? S< Sep30 0:00 [xfsdatad/3] root 336 0.0 0.0 0 0 ? S< Sep30 0:00 [xfsdatad/4] root 337 0.0 0.0 0 0 ? S< Sep30 0:00 [xfsdatad/5] root 338 0.0 0.0 0 0 ? S< Sep30 0:00 [xfsdatad/6] root 339 0.0 0.0 0 0 ? S< Sep30 0:00 [xfsdatad/7] root 340 0.0 0.0 0 0 ? S< Sep30 0:00 [xfsdatad/8] root 341 0.0 0.0 0 0 ? S< Sep30 0:00 [xfsdatad/9] root 342 0.0 0.0 0 0 ? S< Sep30 0:00 [xfsdatad/10] root 343 0.0 0.0 0 0 ? S< Sep30 0:00 [xfsdatad/11] root 344 0.0 0.0 0 0 ? S< Sep30 0:00 [xfsdatad/12] root 345 0.0 0.0 0 0 ? S< Sep30 0:00 [xfsdatad/13] root 346 0.0 0.0 0 0 ? S< Sep30 0:00 [xfsdatad/14] root 347 0.0 0.0 0 0 ? S< Sep30 0:00 [xfsdatad/15] root 399 0.0 0.0 0 0 ? S< Sep30 0:00 [jfsIO] root 400 0.0 0.0 0 0 ? S< Sep30 0:00 [jfsCommit] root 401 0.0 0.0 0 0 ? S< Sep30 0:00 [jfsCommit] root 402 0.0 0.0 0 0 ? S< Sep30 0:00 [jfsCommit] root 403 0.0 0.0 0 0 ? S< Sep30 0:00 [jfsCommit] root 404 0.0 0.0 0 0 ? S< Sep30 0:00 [jfsCommit] root 405 0.0 0.0 0 0 ? S< Sep30 0:00 [jfsCommit] root 406 0.0 0.0 0 0 ? S< Sep30 0:00 [jfsCommit] root 407 0.0 0.0 0 0 ? S< Sep30 0:00 [jfsCommit] root 408 0.0 0.0 0 0 ? S< Sep30 0:00 [jfsCommit] root 409 0.0 0.0 0 0 ? S< Sep30 0:00 [jfsCommit] root 410 0.0 0.0 0 0 ? S< Sep30 0:00 [jfsCommit] root 411 0.0 0.0 0 0 ? S< Sep30 0:00 [jfsCommit] root 412 0.0 0.0 0 0 ? S< Sep30 0:00 [jfsCommit] root 413 0.0 0.0 0 0 ? S< Sep30 0:00 [jfsCommit] root 414 0.0 0.0 0 0 ? S< Sep30 0:00 [jfsCommit] root 415 0.0 0.0 0 0 ? S< Sep30 0:00 [jfsCommit] root 416 0.0 0.0 0 0 ? S< Sep30 0:00 [jfsSync] root 673 0.0 0.0 0 0 ? S< Sep30 0:00 [kjournald] root 727 0.0 0.1 16840 960 ? S<s Sep30 0:00 udevd --daemon root 1273 0.0 0.3 122036 2016 ? Sl Sep30 0:00 /usr/sbin/rsyslogd -c3 root 1306 0.0 0.2 48960 1224 ? Ss Sep30 0:00 /usr/sbin/sshd root 1809 0.0 0.2 21276 1076 ? Ss Sep30 0:00 /usr/sbin/cron root 1873 0.0 1.5 41460 8360 ? Ss Sep30 0:02 /usr/sbin/munin-node root 1896 0.0 0.1 3864 608 tty1 Ss+ Sep30 0:00 /sbin/getty 38400 tty1 root 1897 0.0 0.1 3864 604 tty2 Ss+ Sep30 0:00 /sbin/getty 38400 tty2 root 1898 0.0 0.1 3864 604 tty3 Ss+ Sep30 0:00 /sbin/getty 38400 tty3 root 1899 0.0 0.1 3864 608 tty4 Ss+ Sep30 0:00 /sbin/getty 38400 tty4 root 1900 0.0 0.1 3864 608 tty5 Ss+ Sep30 0:00 /sbin/getty 38400 tty5 root 1901 0.0 0.1 3864 604 tty6 Ss+ Sep30 0:00 /sbin/getty 38400 tty6 101 4526 0.0 0.1 42820 1052 ? Ss 12:27 0:00 /usr/sbin/exim4 -bd -q30m root 8865 0.0 0.2 11668 1432 pts/0 S 13:18 0:00 /bin/sh /usr/bin/mysqld_safe mysql 8980 0.0 9.0 175284 48368 pts/0 Sl 13:18 0:05 /usr/sbin/mysqld --basedir=/usr --datadir=/var/lib/mysql --user=mysql --pid-file=/var/run/my root 8981 0.0 0.1 6480 684 pts/0 S 13:18 0:00 logger -t mysqld -p daemon.error root 13730 0.0 0.8 149144 4712 ? Ss 14:05 0:00 /usr/bin/php5-fpm --fpm-config /etc/php5/fpm/php5-fpm.conf www-data 13731 0.2 11.4 172756 61136 ? S 14:05 0:05 /usr/bin/php5-fpm --fpm-config /etc/php5/fpm/php5-fpm.conf www-data 13732 0.2 8.9 158516 47712 ? S 14:05 0:05 /usr/bin/php5-fpm --fpm-config /etc/php5/fpm/php5-fpm.conf www-data 13733 0.1 8.1 156576 43468 ? S 14:05 0:04 /usr/bin/php5-fpm --fpm-config /etc/php5/fpm/php5-fpm.conf root 14601 0.0 0.2 30600 1240 ? Ss 14:15 0:00 nginx: master process /usr/sbin/nginx www-data 14602 0.0 0.3 30976 1836 ? S 14:15 0:00 nginx: worker process www-data 14603 0.0 0.3 30976 1836 ? S 14:15 0:00 nginx: worker process www-data 14604 0.0 0.5 31552 2852 ? S 14:15 0:00 nginx: worker process www-data 14605 0.0 0.4 31240 2580 ? S 14:15 0:00 nginx: worker process www-data 14606 0.0 0.3 30976 1836 ? S 14:15 0:00 nginx: worker process www-data 14607 0.0 0.3 30976 1836 ? S 14:15 0:00 nginx: worker process www-data 14608 0.0 0.4 31244 2536 ? S 14:15 0:00 nginx: worker process www-data 14609 0.0 0.5 31544 2788 ? S 14:15 0:00 nginx: worker process root 17169 0.0 0.2 17456 1160 pts/0 R+ 14:45 0:00 ps aux root 26391 0.0 0.6 66168 3284 ? Ss 10:32 0:00 sshd: root@notty root 26394 0.0 0.3 42376 2120 ? Ss 10:32 0:00 /usr/lib/openssh/sftp-server root 31500 0.0 0.6 66140 3248 ? Ss 11:33 0:00 sshd: root@pts/0 root 31503 0.0 0.3 20248 1924 pts/0 Ss 11:33 0:00 -bash root 31509 0.0 0.6 66168 3264 ? Ss 11:34 0:00 sshd: root@notty root 31512 0.0 0.3 42180 1984 ? Ss 11:34 0:00 /usr/lib/openssh/sftp-server I'm wondering if this is normal situation? Do I need all of those process? Thanks for any suggestions!

    Read the article

  • Convert color photos of documents to good black-and-white images?

    - by Norman Ramsey
    Since I don't have a copier or scanner, I'm using an 8 megapixel camera to copy documents. This works pretty well except they need a lot of processing afterward. I'd like to get from a photo to a bitmap, but using djpeg -grayscale -pnm photo.jpg | pgmtopbm -threshold -value XXX does not work so well, for two reasons: It's hard to guess what XXX should be, and XXX is different for different photos. Illumination varies, and sometimes a single threshold isn't what's right for the image. How can I do better? The ideal solution will be fully automatic command-line program that I can run on Linux. (I have already written a program to remove dark pixels from the edges of images.)

    Read the article

  • Thunderbird: moving email from local Junk folder to IMAP folder yields "Message contains invalid header"

    - by Peltier
    Whenever I try to move an email from a local Junk folder to an IMAP folder in Thunderbird, I get the following error message: The current command did not succeed. The mail server responded: Message contains invalid header If Thunderbird's Junk folder is an IMAP folder on the server, then after Thunderbird has moved messages to that folder, I can successfully move messages from Junk back into to some other IMAP folder. However, if the Junk folder is not on the server, then moving a message from the local Junk folder to an IMAP folder yields the aforementioned error. The only interesting thing I've found about this error is "Message contains invalid header" from the MozillaZine Knowledge Base. That article officially is about importing folders from another email client, and does not mention the Junk filter as another possible cause. However the proposed solution is not very helpful since it requires manual editing of the message box files. Any better ideas? EDIT: make sure you read the comments before answering the question.

    Read the article

  • Apache2 enable .ini mod in /etc/php5/mods-available

    - by GuiTeK
    One can use the a2enmod [module] command to enable mods located in /etc/apache2/mods-available. But what about mods in /etc/php5/mods-available? When I try to enable a mod in this directory (eg. xdebug), I get the following error: ERROR: Module xdebug does not exist! Yet, /etc/php5/mods-available/xdebug.ini exists. I understand a2enmod may work only with *.load files (it makes sense since *.ini files are just configuration files) but then what's the correct way of enabling modules located in /etc/php5/mods-available?

    Read the article

  • A Generic RIDC Test Program

    - by Kevin Smith
    Many times I have found it useful to use a java program that communicates with WebCenter Content (WCC) using RIDC for testing. I might not have access to the web GUI or need to test a service running as a specific user. In the past I had created a number of "one off" programs that submitted specific services, e.g GET_SEARCH_RESULTS, DOCINFO, etc. Recently I decided to create a generic RIDC test program that could submit any service with the desired parameters based on a configuration file. The programs gets the following information from the configuration file: WCC connection information (host, port) User to use to run service Service to run Any parameters for the service The program will make a connection to the WCC server, send the service request, and print the results of the service call using the getResponseAsString() method. Here is a sample configuration file: ridc.host=localhostridc.port=4444ridc.user=sysadminridc.idcservice=GET_SEARCH_RESULTSidcservice.QueryText=dDocType <matches> `Document`idcservice.SortField=dDocNameidcservice.SortDesc=ASC There is a readme file included in the zip with instructions for how to configure and run the program. The program takes one command line argument, the configuration file name. The configuration file name is optional and defaults to config.properties. If you have any suggestions for improvements let me know. Right now it only submits a single service call each time you run it. One enhancement I have already thought about would be to allow you to specify multiple services to tun in the configuration file. You can do that with the current program by having multiple configuration files and running the program multiple times, each with a different configuration file. You can download the program here.

    Read the article

  • Windows Server 2008 Antivirus Software with an API

    - by Dave Jellison
    I'm looking for an Antivirus package that is compliant with Windows Server 2008. That's not the hard part. What I need is an API layer on the Antivirus that i can call from managed .net code. For example: I am developing an Asp.Net (C#) website that allows users to upload files to the web server which the web site resides on. We have full control of the server so there are no security/rights issues on the server. I need to be able to run the antivirus algorithm on the newly uploaded files without (hopefully) shelling out to a command-ilne version of the software. Does anyone know of such a package?

    Read the article

  • Redhat | error in mod_swgi installation

    - by MMRUSer
    I'm getting the following error when I try to install mod_wsgi ./configure checking for apxs2... no checking for apxs... /usr/sbin/apxs checking Apache version... 2.2.3 configure: creating ./config.status config.status: creating Makefile make /usr/sbin/apxs -c -I/usr/local/include/python2.6 -DNDEBUG mod_wsgi.c -L/usr/local/lib -L/usr/local/lib/python2.6/config -lpython2.6 -lpthread -ldl -lutil -lm /apr-1/build/libtool --silent --mode=compile gcc -prefer-pic -O2 -g -pipe -Wall -Wp,-D_FORTIFY_SOURCE=2 -fexceptions -fstack-protector --param=ssp-buffer-size=4 -m32 -march=i386 -mtune=generic -fasynchronous-unwind-tables -fno-strict-aliasing -DLINUX=2 -D_REENTRANT -D_GNU_SOURCE -D_LARGEFILE64_SOURCE -pthread -I/usr/include/httpd -I/usr/include/apr-1 -I/usr/include/apr-1 -I/usr/local/include/python2.6 -DNDEBUG -c -o mod_wsgi.lo mod_wsgi.c && touch mod_wsgi.slo sh: /apr-1/build/libtool: No such file or directory apxs:Error: Command failed with rc=8323072 . make: *** [mod_wsgi.la] Error 1 mod_wsgi 3.2 Apache 2.2 Python 2.6 apr-1.2.7-11 Is this error because of a missing package.. or else how do I solve this issue?

    Read the article

  • How to install Imagick on Mac OS with XAMPP

    - by Cat
    I'm having some trouble installing Imagick on a Mac. I have XAMPP installed and when I run 'sudo pecl install imagick', I get this error: checking ImageMagick MagickWand API configuration program... configure: error: not found. Please provide a path to MagickWand-config or Wand-config program. ERROR: `/private/tmp/pear/temp/imagick/configure --with-imagick="/Applications/XAMPP/xamppfiles/bin"' failed The error above shows up when I input /Applications/XAMPP/xamppfiles/bin after Please provide the prefix of Imagemagick installation [autodetect] Do I need to install some other library before running the Imagick install command?

    Read the article

  • crontab environment

    - by Adamski
    I have written various scripts to launch Java server applications, which are typically run for 24 hours before being shut down (by invoking the same script with a different parameter). The script relies on environment variables defined in a file: ~/<user>.env, which I source from .bashrc. This works fine when invoking the script from the command line but if I want to add the script as a crontab entry I run into the problem where .bashrc isn't read. My question: What is the best practice approach for solving this problem? I realise I could define a crontab entry such as: * * * * 1-5 /usr/bin/bash -c '. /home/myuser/myuser.env && /home/myuser/scripts/myscript.sh' ... but this seems plain ugly. Alternatively I could source myuser.env at the beginning of every script, but this would become a nightmare to maintain. Any help appreciated.

    Read the article

< Previous Page | 539 540 541 542 543 544 545 546 547 548 549 550  | Next Page >