Search Results

Search found 18729 results on 750 pages for 'edit'.

Page 544/750 | < Previous Page | 540 541 542 543 544 545 546 547 548 549 550 551  | Next Page >

• Problems reviving old pc including graphics card issue.

  - by Mick

  I have a PC that seemed to have died years ago that I am trying to revive. It has a dual core athlon processor and a gigabyte motherboard. It had two dual output graphics cards, and I have long since forgotten which output would print out the diagnostic information as the PC starts up. Also I suspect that the resolution set on all the monitors was probably higher than my current single monitor is capable of displaying. The motherboard also has a built in graphics card, so I thought it may be simplest to remove both the graphics cards and plug my monitor into the onboard graphics just while I get things going. Does that seem sensible? Now the other problem: The PC has two hard drives. I have no idea which one is the primary one it is attempting to boot from. When I power up, the fan comes on and I hear some chuga-chuga-pause chuga-chuga-pause repeat indefinitely. I'm not sure which device is making the noise. There are no-beeps at any time. I see nothing on the screen at any time, not even for a second. Any suggestions? EDIT: If T start up the PC without the power connected to the CDrom there is no chuga-chugan noise.

  Read the article

• Dropbox picture sync: Skip RAW files?

  - by Steven Lu

  I like the convenience of having Dropbox keep track of my photos because it tends to work with my devices over 3G (I am often tethering to my phone with my iPad and Macbook) as well as Wifi, but it's a waste of network traffic to sync the raw files from my camera or memory card. It clutters up the dropbox list and the files are just huge. Is there a way to configure the Dropbox client so that it ignores a certain file extension for the picture sync? Also, I suspect that if I just go and delete the raw files, that the next time I plug in the memory card and tell Dropbox to sync, it will re-download the raw files. Which would be terribad. I could switch to iCloud for Photo Stream, I suppose, but there will be no access via 3G that way. And I've already got years of experience with Dropbox so I know it's going to just work. I think any method that works for filtering files to exclude from sync on Dropbox in general should work here too. Edit: Wow there are 19k votes for this exact request.

  Read the article

• How do I configure Jetty (via jettyrunner) so that it names a character set in the Content-Type response header?

  - by Pointy

  I use Jetty (via the oh-so-handy Jetty Runner) for day-to-day web application testing. One thing I've recently stumbled on is the fact that I don't get a character set called out in the "Content-Type" response header all the time. I do get it in response to my application's XMLHttpRequest transactions, but not for plain old pages loaded by <a> links or whatever. I've read a little bit about how to set up a Jetty config file, but I've never been able to completely understand that; all servlet containers are complicated, and while Jetty is pretty simple it's just weird enough that I don't grok the overall idea. Thus, all I do to launch my app is to run the Jetty Runner .jar file with a couple of simple arguments to set up the port number and logfile path, and then I just give it the .war file to run. It works great — except for the missing character set :-) Anybody have a quick sample config file that might fix this? edit — oh if it matters, I'm running Jetty 7.0.0 RC3; I've also tried with a slightly newer version (still 7.something) with exactly the same issue. All my testing is on Ubuntu.

  Read the article

• Safe to remove Python2.6 files?

  - by darkfeline

  I'm using Linux Mint 11 (will upgrade soon), and I've noticed that, even though I don't have any python2.6 packages installed with apt, there's a bunch of residual python2.6 files scattered around my drive, including, but not limited to, dist-packages in /usr/lib/python2.6 and various /usr/share stuff. Is there any way to test if these files are still being used? I'm tempted to sudo rm -rf the lot of them, but I'm scared it'll break stuff. Also, does anyone have any idea where these files could have come from? I believe I had python2.6 installed once upon a time, but I made sure to --purge them, so there shouldn't be any trace of them left, right? EDIT: after using a quick script to check all of the files, it appears most of them belong to important packages, so I won't try weeding out the few which I know are probably useless. Although I am curious why so many packages have python2.6 files when I don't even have it installed. These files are not associated with any packages and I'm not sure if they are safe to remove: /usr/bin/ipython2.6 /usr/lib/python2.6/dist-packages/distribute-0.6.15.egg-info /usr/lib/python2.6/dist-packages/easy_install.py /usr/lib/python2.6/dist-packages/IPython /usr/lib/python2.6/dist-packages/ipython-0.10.1.egg-info /usr/lib/python2.6/dist-packages/setuptools /usr/lib/python2.6/dist-packages/setuptools.egg-info /usr/lib/python2.6/dist-packages/setuptools.pth /usr/lib/python2.6/dist-packages/site.py /usr/lib/python2.6/dist-packages/wx.pth /usr/local/lib/python2.6 /usr/local/lib/python2.6/dist-packages /usr/local/lib/python2.6/site-packages /usr/share/man/man1/ipython2.6.1.gz

  Read the article

• Clone a Windows Installation to a 3TB Hard Drive; MBR to GPT

  - by DanBlakemore

  I have Windows 7 Professional 64-bit installed on my desktop. Unfortunately for me and my wallet my hard drive is failing. I have purchased a 3TB hard drive as a replacement for my current 2TB drive. I would like to avoid as much hassle as possible in moving to this new drive so I would like to copy my current partition to the new drive using Gparted. The problem is that I suspect that my current partition is MBR, and I need GPT on my new drive since it is 3TB. Can I simply copy the MBR partition onto the new disk and then convert it to GPT after the fact (can you even convert the type of a partition)? Or would I need to somehow copy the contents of the partition into a GPT partition on the new drive? How do I go about making this transistion? Also, are there any issues I should be wary of booting to a GPT partition? If it matters, my motherboard is 1 year old as of May, 2012. Edit: My motherboard is 1 day old. My old one does not have UEFI compatibility, so I decided to make an upgrade to Intel today given that I would need a UEFI motherboard to use my new HDD. How much can I use a dying hard drive (bad sectors according to Hitachi Drive Fitness Test)? I have assumed not at all, to be safe.

  Read the article

• How do I automatically connect my client to an ODBC data source on another machine with dynamic IP?

  - by Kdansky

  At the customer's place, we've got a postgres DB on a server, and a few clients. We connect them through ODBC-drivers, and all machines run windows (usually XP). Now we had a few annoying issues: The client "forgets" some flags in the ODBC drivers, such as ByteA as LO. Every time anything changes, we have to reset that, and type in the password, and sometimes even the IP of the server. On x64 machines running Windows 7, configuring this is a pain as the system settings dialogue will only show 64-bit connections by default. And most importantly: If the server changes IP because the customer restarts or replaces a switch, all connections are lost. Annoyingly, this cannot be fixed with just correcting the IP, but rather, we have to check every single place (even hba_conf) because all the settings magically disappear. Our customers often are very small companies, where "server" means "that one PC in the other room", and not "Oracle mainframe in the dungeon", so we don't want to rely on them not restarting switches. Is there a better way than to rely on these really unstable settings? Are these settings somewhere in a file which I could edit manually, to make fixing it easier?

  Read the article

• Hibernation fails; The system cannot find the file specified

  - by GMMan

  Recently I installed Ubuntu 12.04.1 LTS on my Lenovo Y480. Hibernation was working properly after the Ubuntu install, but I was making sure all of the operating systems on my system worked, including OneKey Recovery (recovery partition). It is of note that I installed Windows 7 from scratch with a disk image I downloaded off of my university's DreamSpark program, and further to that I had to image the partition with Paragon Backup & Recovery, repartition to convert the Windows partition to extended, install Ubuntu, and then restore the image. During that process I also used the Windows disc to edit the BCD as to reuse the existing entry for the restored partition. I also used the automated "repair your computer" option. With verification, I noticed that the "repair your computer" option actually wrote to the wrong BCD (the recovery partition), and I mounted the partition and restored the original BCD (from a copy I made earlier), and rebooted. At this point my GRUB broke, and I was able to restore it. At this point hibernation broke. I tried powercfg /h off and powercfg /h on, rebooted, and nothing. Also tried increasing the hibernation file size as directed on this post, but it still doesn't work. Executing shutdown /h yields The system cannot find the file specified.(2). What file? It seems that mounting the system partition sometimes works, but I don't want to keep it mounted in case it gets written to accidentally. How do I permanently fix this?

  Read the article

• Made a .dmg for a project; user can't open it - "no mountable file systems"

  - by dragonridingsorceress

  Hello, We don't know a great deal about Macs. We had to make an installer, and were told to try a .dmg So we put together version 1, and it seemed to work. We had one application file, which had our icon, and one folder. The user was instructed to drag these into the Applications folder, of which there was the Mac version of a shortcut in the dmg. Then we were told we needed to update files, and assured that we could do so via drag-and-drop. So we did; we dragged them into the folder in the dmg. We tested it (on the computer we were using to edit the dmg) and it seemed to work. So we burnt it onto a disk (along with a windows installer that actually works!). I've just gotten an email from the recipient. She's got a Mac laptop. She inserted the disk, doubleclicked on it, doubleclicked on the .dmg, and got a Warning: no mountable file systems. Screenshot: http://www.flickr.com/photos/97292258@N00/5101670174/ I have the dmg (not on a disk) and am able to open it with no difficulty. How can we get it to work for our recipient?

  Read the article

• How to know who accessed a file or if a file has 'access' monitor in linux

  - by J L

  I'm a noob and have some questions about viewing who accessed a file. I found there are ways to see if a file was accessed (not modified/changed) through audit subsystem and inotify. However, from what I have read online, according to here: http://www.cyberciti.biz/tips/linux-audit-files-to-see-who-made-changes-to-a-file.html it says to 'watch/monitor' file, I have to set a watch by using command like: # auditctl -w /etc/passwd -p war -k password-file So if I create a new file or directory, do I have to use audit/inotify command to 'set' watch first to 'watch' who accessed the new file? Also is there a way to know if a directory is being 'watched' through audit subsystem or inotify? How/where can I check the log of a file? edit: from further googling, I found this page saying: http://www.kernel.org/doc/man-pages/online/pages/man7/inotify.7.html The inotify API provides no information about the user or process that triggered the inotify event. So I guess this means that I cant figure out which user accessed a file? Only audit subsystem can be used to figure out who accessed a file?

  Read the article

• Verification of downloaded package with rpm

  - by moooeeeep

  I wanted to install a package on CentOS 6 via rpm (e.g., the current epel-release). EDIT: Of course I would always prefer the installation via yum but somehow I failed to get that specific package installed using this normal approach. As such, the EPEL/FAQ recommends Version 2. As I'm downloading the package through an insecure channel (http) I wanted to make sure that the integrity of the file is verified using information that is not provided with the downloaded file itself. Is this especially true for all of these approaches? I've seen various approaches to this on the internet: Version 1 rpm -ivh http://dl.fedoraproject.org/pub/epel/6/x86_64/epel-release-6-7.noarch.rpm Version 2 rpm -Uvh http://dl.fedoraproject.org/pub/epel/6/x86_64/epel-release-6-7.noarch.rpm Version 3 wget http://dl.fedoraproject.org/pub/epel/6/x86_64/epel-release-6-7.noarch.rpm rpm --import https://fedoraproject.org/static/0608B895.txt rpm -K epel-release-6-7.noarch.rpm rpm -i epel-release-6-7.noarch.rpm I do not know rpm very well, so I wondered how they might differ? My guess (after reading the manpage) is that the first should only be used when the package is previously not installed, the second would additionally remove previous versions of the package after installation, the first two omit some verification steps before the actual installation that are done by rpm -K. So my main questions at this point are Are my guesses correct or am I missing something? Is the rpm --import ... implicitly done for the first two approaches as well, and if not, isn't it necessary to do so after all? Are these additional checks performed by rpm -K ... any relevant? What is the best (most secure, most reliable, most maintainable, ...) way of installing packages via rpm in general?

  Read the article

• Manual Http error response code in non-existent folder via routing

  - by Slytherin

  Apache server running on ubuntu-like linux I am getting unexpected behaviour when i try to manually send error response. If my .htaccess is responsible for the error response , then appropriate error document is loaded and displayed , with according response code in browser console. However , if my router is origin of the response code , then i get blank screen , but correct response code. .htaccess looks like this RewriteEngine On # RewriteBase / RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule !\.(css|js|icon|zip|rar|png|jpg|gif|pdf)$ index.php [L] ErrorDocument 404 /err/404.html ErrorDocument 403 /err/403.html ErrorDocument 500 /err/500.html part of my router that sends the response is the following header("HTTP/1.1 403 Forbidden"); trying this format didnt help either header("HTTP/1.1 403 Forbidden", TRUE, 403); I also tried HTTP/1.0. Furthermore i was thinking that maybe relative path to error page might be an issue , but discarded this idea after attempting to access a document that is forbidden via .htaccess EDIT I should also point out , this scenario happens when URL for not-existing article is requested. Is it possible that Server is looking for a .htaccess file in a folder based on URL ? Eg: domain/blog/non-existent , is server looking for blog folder ? I am specifically asking this because there is no blog folder

  Read the article

• New AD user request form and workflow

  - by user66390

  I'm wondering if anyone is providing a solid solution for creating New Network User Account Request forms, and attaching workflows to them to automate account creation? I'm currently investigating a number of options, but am surprised that such a ubiquitous task hasn't been solved a dozen times over and thoroughly documented. Or at least isn't integrated into current off-the-shelf change management and ticketing systems. Ideally, I'd like for our current ticketing system, ServiceDesk+ to present a standard 'New User' form to department heads, which they can fill in with the required new user details. This triggers a workflow that submits the request as a ticket that can be reviewed and actioned. Actioning the ticket triggers a workflow that creates a user in AD with the details provided, and notifies the department head upon completion. All told, a pretty standard requirement that I'm sure most organizations have. What are other people doing to accomplish this? Edit: I should add, I'm more looking for "supported" methods. As is, I've submitted a number of scripted solutions, none of which have met with manager approval.

  Read the article

• iptables blank after reboot

  - by theillien

  We've started encountering an issue with iptables on our RHEL 6.3 systems in that after a reboot, when the service starts, the rules are not loaded. We get the empty ruleset: [msnyder@matt-test ~]$ sudo iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination This is in spite of the fact that we have rules defined and the service is, indeed, running. That I know because when I run service iptables start it simply drops back to the prompt. If I run service iptables restart it actually stops and then restarts the service. And, of course, if I run service iptables stop it indicates that iptables is actually stopping. Knowing that I need to restart the service, I do so and the rules load up properly. They simply don't get loaded after a reboot. Unless they get loaded differently during a reboot I don't see how our rules would be wrong. If they were, they wouldn't even load during a service restart. Has anyone else ever encountered this? EDIT: The rules are already saved in /etc/sysconfig/iptables. They are not added on the fly from the command line so service iptables save is unnecessary.

  Read the article

• Can anyone help me make my reverse proxy actually cache?

  - by Lenary

  Hi folks, I'm trying to configure a Reverse Caching Proxy but so far have had no luck. I would preferrably like to use apache (that will be all it will be used for), but am open to solutions using other software that can also run on Mac OS X 10.6 (I have also tried using Varnish and Squid, but with no more luck). We're running a system with about 80 mac mini clients that will be requesting lots of video from a server. To reduce load, we thought we could use Apache (which comes on the macs by default) to cache this video forever (or at least as long as possible) onto the macs' disks. I have managed to get a reverse proxy set up with apache using ProxyPass etc, but when i tried to add CacheEnable disk / to the configuration, nothing happened (i do have mod_disk_cache included). Can anyone help with my issue? The apache config file is here Thanks in advance Edit: So far I have been testing it with smaller text files, and it hasn't been caching properly. This suggests it is nothing to do with us actually downloading video, but actually to do with the cache configuration.

  Read the article

• Take a regular Windows 7 clone with clonezilla (device-to-image)

  - by Mario De Schaepmeester

  I am unexperienced with cloning software and I've decided to use Clonezilla as it seemed best as freeware. I chose device image and left most options standard. I chose expert mode anyway to see what I could configure, and decided to try the lzop algorithm instead of the default one for compression. The rest was left at default. When Clonezilla asked me which partitions to clone (I chose parts to image), I chose the C:\ drive but Windows 7 also creates a 100MB partition on setup for system files (the actual boot partition?). I copied that into the image as well. The reason I didn't choose disk to image is that I also have a data partition that needs to stay intact. Now I'm simply not sure that this is the way to go, should I ever need to restore my disk image. Will Clonezilla know what to do with both partitions and will Windows 7 work perfectly after restoring? Edit: apparantly a similar question has been asked before. The link to the first article in the answer is not relevant to me since it covers a device-to-device clone. It appears the windows installation disk can repair the 100MB partition. As for Clonezilla, it copies "hidden data after the MBR" by default too. I don't know, I feel I'll be allright whether by restoring the partition with Clonezilla or repairing it with the Windows 7 disk.

  Read the article

• Plug-in device to front USB computer *sometimes* restarts

  - by Mark A. Nicolosi

  I've got a strange problem that very occasionally (maybe once a month) when I plug-in something to the front USB on my computer, the computer suddently restarts. This also happens when I touch the front USB ports sometimes. This has been going on for a few years and a lot of the components in my PC have changed. I thought it was my home wiring, but I moved last year and it still happened. I thought maybe it was the motherboard, but that was upgraded 9 months ago and it still happens. I thought it was my case, but I changed that recently and it still happens. I thought maybe it was my PSU, but I upgraded that yesterday and it still happens. I'm pretty sure this is an electro-static thing, but I thought that modern computers have protection against this sort of thing. Maybe I should move my case off the floor (carpet) and stop wearing songs all the time. Edit: Just to clarify this is a computer that I built. The components have been upgraded throughout the years and it's not much the same computer anymore. This doesn't happen very often, but it is annoying, because I don't know what the cause is. Anyone have any ideas?

  Read the article

• nVidia performance with newer X and newer driver abysmal with Compiz

  - by Nakedible

  I recently upgraded Debian to Xorg 2.9.4 and installed nvidia-glx from experimental, version 260.19.21. This was somewhat of an uphill battle as the dependencies for the experimental nvidia-glx package are still somewhat broken. I got it to work without forcing the installation of any packages and without modifying the packages. However, after the upgrade compiz performance has been abysmal. I am using the desktop wall plugin and switching viewports is really slow - takes a few seconds for each switch. In addition to this, every effect that compiz does, such as zoom animations for icons when launching applications, takes seconds. The viewport switching speed changes relative to the amount of windows on that virtual screen - empty screens switch almost at normal speed, single browser windows work almost decently, but just 4 rxvt terminals slows the switches down to a crawl. My compiz configuration should be pretty basic. Xorg is likewise configured without anything special - the only "custom" configuration is forcing the driver name to be "nvidia". I've fiddled around with the nvidia-settings and compizconfig trying different VSync settings, but none of those helped. My graphics card is: NVIDIA GPU NVS 3100M (GT218) at PCI:1:0:0 (GPU-0). This is laptop GPU that is from the Geforce GTX 200 series. Graphics card performance should naturally be no problem. EDIT: In the end, nothing really worked, and I got really annoyed with the state of compiz and its support in Debian. Many nVidia driver revisions have passed and I am using Gnome 3 now, so I am accepting the best answers to this question even though the issue was not resolved.

  Read the article

• What to do after a fresh Linux install in a production server?

  - by Rhyuk

  I havent had previous experience with the 'serious' IT scene. At work I've been handed a server that will host an application and MYSQL (I will install and configure everything), this will be a productive server. Soon I will be installing RHEL5 to it but I would like to know like, if you get a new production server, what would be the first 5 things you would do after you do a fresh Linux install? (configuration/security/reliability wise) EDIT: Added more information regarding the server enviroment and server roles: -The server will be inside my company's intranet/firewall. -The server will receive files (GBs) in binary code from another internal server. The application installed in this server is in charge of "translating" all that binary into human readable input. Server will get queried to get this information. -Only 2-3(max) users will be logging in. -(2) 145GB HDs in RAID1 for the OS and (2) 600GB HDs in RAID1 also for data. I mean, I know I may not get the perfect guideline. But at least something thats better than leaving everything on default.

  Read the article

• How to circle out something in a picture?

  - by T...

  What is the easiest way to circle out something in a picture, like this example This is accomplished in Gimp: Here are the steps necesary to draw an empty ellipse without clearing the contents of the image below it. 1 - Layer New layer 2 - Make the layer to be the same size as the image and layer fill type to transparency. This should be already selected by default. 3 - On the toolbox select the ellipse select tool and make an ellipse 4 - Use the bucket fill tool to paint the ellipse with your desired color. 5 - Right click on it and go to Select Shrink... 6 - Type in how many pixels you want the border to be and click ok. 7 - Go to the menu and click Edit Clear. I feel it is very indirect, in the sense that first fill out the region enclosed by the ellipse, and then shrink the region to the boundary. I wonder if there is a quicker and more direct way to circle out something, such as by directly drawing the boundary? My OS is Ubuntu. What I was asking may be done outside of gimp, but must be by some software under Ubuntu. Thanks!

  Read the article

• Apache file appearing in directory list, but giving 404 when attempting access?

  - by aayush

  Please forgive my lack of knowledge, this is more of a learning project than anything else. I have a linux box, and it works pretty much fine. When i go to example.com/css it says theres one file in there, bootstrap.min.css When i go to example.com/css/bootstrap.min.css, it gives me a 404 error. I have only one htaccess file to remove the index.php from the url, which also i renamed to htaccess (Instead of .htaccess, so apache wont find it) and i restarted the server, yet no help. I also tried to chmod the css file 755 but no help. Contents of the htaccess file: RewriteEngine On RewriteBase / # Allow any files or directories that exist to be displayed directly RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule ^(.*)$ index.php?/$1 [L,QSA] Please help, i am very confused about this. I tried to google excessively but i came up with nothing. Edit: I found the solution to be renamed the htaccess file to something entirely different and restarting. Is there any way i can still implement the losing of the .php?

  Read the article

• Strange Photoshop Problem: Can not select, zoom, paint, option button 'locked'

  - by nikcub

  I have a very strange problem with Photoshop. I can not use any of the tools, since the cursor appears 'locked'. If I select v on my keyboard, it goes to the zoom tool, but the cursor does not change. If I select the paintbrush tool, I can only paint if I hold down the option key. This is what the cursor look like (I had to paint it since I couldn't capture it). It is a rectangle with two lines through it. I am running Photoshop CS4 on a Macbook Pro with Mac OS X 10.6.6. Using both the trackpad and an external Logitech MX5000 mouse I see the same issue. This started when I fired up Photoshop today for the first time in a while. I can't remember changing any options or doing anything that could cause this. Is it possible that the option key is somehow locked in place, or there is some equivalent of num lock on? Very strange problem, I would appreciate any help anybody can offer. Edit: To add, the icon remains the same within all the menu options - it never goes back to being just a normal mouse cursor. Also, right click works fine, and if I hold down option, the cursor goes back to normal and I can paint with it. I can't use Marquee, Lasso, Crop, Type etc. even with option held down. When I go into Bridge, it is the same icon.

  Read the article

• Wordpress on Apache is redirecting all https to http

  - by Krist van Besien

  I have a problem with a wordpress site on a server I admin. I don't know anything about wordpress however. My problem is that we want the site to be accessed over https, bot somehow all requests to https:// URLs are answered by the server with a 302, redirecting to http. The wordpress site itself is configured to use https, and we see that in the pages that are generated the links are all https links. In the apache config there are no rewrite rules and no redirects. However, any request to a https:// URL is answered with a redirect to the equivalent http URL. And I really would like to know where these redirects are coming from, what is generating these redirects. I've increased the loglevel on the webserver to DEBUG, but did not get any info there. I tried to enable debug logging in wordpress per the recipy I found here: http://codex.wordpress.org/Debugging_in_WordPress But did not get a debug.log file in the directory where one should appear. I'm really at a loss here, and need to fix this urgently. Any hints as where to start looking? Apache is 2.2.14 on Ubuntu. There are several other virtual hosts on this server, using php and https without any problem... Edit: I created a small info.php script and dropped that in the webservers' root. Calling this yields the output of the script, no redirect is generated. This suggest that it's not the webserver, but wordpress that is doing it. A second thing I noticed is that the redirect comes with several cookies, one of which has "httponly" set. Could that be it?

  Read the article

• Allowing Sharepoint to relay email through Exchange

  - by dunxd

  I have written a Sharepoint 2007 web part that sends a field from a form to a specified email address. I have got the form working as I require, but at present it can only send to internal email addresses. Sharepoint's email functions use SMTP to send to our Exchange 2003 server, but because our Exchange server is configured to prevent relaying, if the To: address is not at a local domain, it won't deliver the mail. I don't want to open up our Exchange server to be a completely open relay. What I want is to allow my Sharepoint servers to send mail to addresses outside our domain. The following seem possible: Allow all mail sent from one of the Sharepoint servers to be relayed Allow all mail from a web application pool account to be relayed (I am not sure that the application pool authenticates to the SMTP server though) A combination of the two Can anyone advise on the best way of doing this? Is setting up a dedicated SMTP server on the Exchange server (not a separate physical server) the right way of going about this? EDIT: Note this is for Exchange 2003. There is a post on setting this up in Exchange 2007 which appears to have recognised the frequent requirement to do what I need. It doesn't give much detail on 2003 though. Can anyone expand?

  Read the article

• How to prevent an SSD from disappearing from BIOS

  - by Midimatt

  I've only recently upgraded my old machine to a new one with a brand new 60gb SSD as my boot drive and a 1TB main drive. Paranoid about completely breaking my SSD, I read up on a lot of issues that I needed to watch out for, including making sure AHCI was turned on and trim enabled. PC has been working fine for a few weeks now, until today. My wife was watching some TV on the machine when it started to act strange and eventually blue screened. She rebooted and the boot mgr was missing. When I got home from work I checked the BIOS and the drive had disappeared. I panicked and looked up some possible fixes, and I discovered a large amount of people having problems with the drive firmware, especially on OCZ Vertex and Agility drives, and my drive is an Agility 3 drive. The problems included blue screens followed by missing drives, and a solution was to reset the CMOS and try again. This worked, and now everything seems to be working fine. My question is, is there any way to prevent this from happening? Am I missing a setting for my SSD? All of the posts I found were from early to mid-2011 nothing for the end of 2011 to 2012. So I am wondering if I've missed anything. EDIT: Checked my drives firmware and it is 2.15, which has had issues reported by users.

  Read the article

• mysqld-nt.exe exist in task list, but actually it's not running?

  - by PHP

  mysqld-nt.exe is showing in the task manager, but I cannot connect to it. I tried: telnet localhost 3306 And it fails to connect. So I restarted the server,and it's ok. This happens every day. Any ideas? EDIT Here is the error log(I didn't find anything abnormal though): 100122 10:11:16 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: Normal shutdown 100122 10:11:16 InnoDB: Starting shutdown... 100122 10:11:18 InnoDB: Shutdown completed; log sequence number 0 22939338 100122 10:11:18 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: Shutdown complete 100122 10:12:40 InnoDB: Started; log sequence number 0 22939338 100122 10:12:42 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: ready for connections. Version: '5.0.24-community-nt' socket: '' port: 3306 MySQL Community Edition (GPL) 100123 16:20:44 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: Normal shutdown 100123 16:20:44 InnoDB: Starting shutdown... 100123 16:20:46 InnoDB: Shutdown completed; log sequence number 0 22939832 100123 16:20:46 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: Shutdown complete 100123 16:22:09 InnoDB: Started; log sequence number 0 22939832 100123 16:22:11 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: ready for connections. Version: '5.0.24-community-nt' socket: '' port: 3306 MySQL Community Edition (GPL) 100125 9:18:59 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: Normal shutdown 100125 9:18:59 InnoDB: Starting shutdown... 100125 9:19:00 InnoDB: Shutdown completed; log sequence number 0 22941001 100125 9:19:00 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: Shutdown complete 100125 9:20:22 InnoDB: Started; log sequence number 0 22941001 100125 9:20:25 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: ready for connections. Version: '5.0.24-community-nt' socket: '' port: 3306 MySQL Community Edition (GPL)

  Read the article

< Previous Page | 540 541 542 543 544 545 546 547 548 549 550 551  | Next Page >