Search Results

Search found 16598 results on 664 pages for 'device center'.

Page 547/664 | < Previous Page | 543 544 545 546 547 548 549 550 551 552 553 554  | Next Page >

  • WOL doesn't work if set to anything other than `a` but this setting makes it boot all the time

    - by Elton Carvalho
    I manage a small "cluster" of 4 Xeon machines with Intel boards in my lab. They are all plugged to a 5-port 3-Com switch with static IP addresses like 10.0.0.x. They are all running OpenSuse 11.4 and their /home/ is served by one of the machines (node00) via NFS. They are plugged to an UPS that can keep them on for ca. 15 minutes, but there are lots of electric shortages due to "unscheduled maintenace" that are longer than this. So they end up being powered down without notice. If I set the BIOS to turn them on after power shortages, the issue is that they all boot at the same time and, if node00 decides to run fsck in the /home/ partition, it does not finish booting before the others try to NFS mount their /home/. I am trying to make wake on lan work, so I can choose to boot the NFS clients only after the server has successfully booted. The problem is that when I run ethtool I get an output like this: Supports Wake-on: pumbag Wake-on: g Theoretically, it is set to wake on MagicPacket(tm), according to the manual. But sending the WOL packet using wol -i 10.0.0.255 $MACADDR does not wake up the box after I shut it down with halt. The ethernet link led blinks after I send the packet, so it appears to be getting to the machine. However, if I set it up with ethtool -s eth1 wol bag, the machine always wakes up right after halting, even if I don't send the Magic packet. This means that the device can wake up with LAN activity, but seems to be ignoring the magic packet. Setting wol ag does not wake the box with the MagicPacket. Does setting wol a mean that it should boot with any broadcast message? How can I diagnose the issue of the machine not waking up with the MagicPacket even though I am sending it and it's set up to wake up with it? Thanks in advance!

    Read the article

  • Connecting multiple access points

    - by mohsen farahanipoor
    I'm working on a big project. We want to create a wireless network throughout the building with 15 floors. My idea is that we should set up one unified wireless access point at least in each floor...in case of signal attenuate, we use Access point extender/repeater. I selected DWL-6600AP from among D-Link industrial access points. I want to implement a single wireless LAN throughout the building. Is it possible to combines multiple DWL-6600 access points to achieving just a single WLAN? Can a wireless switch controller do this task? Can these Access Points interfere with each other? What is the solution? I read D-Link website's learning materials, but I am still confused. My other question is around the connecting these APs to Wireless Switch Controller - Is it possible to use power line for connecting DWL-6600 to Wireless Switch Controller device? My main goal is that clients with portable devices such as laptops should be easily connected to the network to share & have communication without any more manual configuration as they are already connected to a single network.

    Read the article

  • Cut (smart edit) .mts (AVCHD Progressive) files un Ubuntu Lucid

    - by pts
    I have a bunch of .mts files containing AVCHD Progressive video recorded by a Panasonic camera, and I need software on Ubuntu Lucid with which I can remove the boring parts, and concatenate the interesting parts, all this without reencoding the video stream. It's OK for me to cut at keyframe boundary. If Avidemux was able to open the files, it would take about 60 hours of work for me to cut the files. (At least that was it last time I tried with similar videos, but of a file format supported by Avidemux.) So I need a fast, powerful and stable video editor, because I don't want that 60 hours of work go up to 240 or even 480 hours just because the tool is too slow or unstable or has a terrible UI. I've tried Avidemux 2.5.5 and 2.5.6, but they crash trying to open such a file, even if I convert the file to .avi first using mencoder -oac copy -ovc copy. mplayer can play the files. I've tried Avidemux 2.6.0, which can open the file, but it cannot jump to the previous or next keyframe etc. (if I make it jump to the next keyframe, and then to the previous keyframe, it doesn't end up at the original keyframe, sometimes displays an error etc.). Also I'm not sure if Avidemux 2.6.x would let me save the result without reencoding. I've tried Kdenlive 0.7.7.1, but playback is very choppy, and it cannot play audio at all (complaining that SDL cannot find the device; but many other programs on the system can play audio). It would be a pain to work with. I've tried converting the .mts file to .mkv using ffmpeg -i input.mts -vcodec copy -sameq -acodec copy -f matroska output.mkv, but that caused too much visible distortions in the video in both mplayer and Avidemux. I've tried converting the .mts file with TsRemux.exe, but Avidemux 2.5.x still can't open that file. Is there another program to cut and concatenate the files? Is there a preprocessor which would create a file (without reencoding the video) on which Avidemux wouldn't crash?

    Read the article

  • IPTABLE & IP-routed netwok solution for HOST net and VM's subnet

    - by Daniel
    I've got ProxmoxVE2.1 ruled KVM node on Debian and bunch of VM's guests machine. That is how my networking looks like: # network interface settings auto lo iface lo inet loopback # device: eth0 auto eth0 iface eth0 inet static address 175.219.59.209 gateway 175.219.59.193 netmask 255.255.255.224 post-up echo 1 > /proc/sys/net/ipv4/conf/eth0/proxy_arp And I've got two working subnet solution auto vmbr0 iface vmbr0 inet static address 10.10.0.1 netmask 255.255.0.0 bridge_ports none bridge_stp off bridge_fd 0 post-up ip route add 10.10.0.1/24 dev vmbr0 This way I can reach internet, to resolve outside hosts, update and download everything I need but can't reach one guest VM out of any other VM's inside my network. The second solution allows me to communicate between VM's: auto vmbr1 iface vmbr1 inet static address 10.10.0.1 netmask 255.255.255.0 bridge_ports none bridge_stp off bridge_fd 0 post-up echo 1 > /proc/sys/net/ipv4/ip_forward post-up iptables -t nat -A POSTROUTING -s '10.10.0.0/24' -o vmbr1 -j MASQUERADE post-down iptables -t nat -D POSTROUTING -s '10.10.0.0/24' -o vmbr1 -j MASQUERADE I can even NAT internal addresses: -t nat -I PREROUTING -p tcp --dport 789 -j DNAT --to-destination 10.10.0.220:345 My inexperienced mind is ready to double VM's net adapters: one for the first solution and another - for second (with slightly different adresses) but I'm pretty sure that it's a dumb way to resolve the problem and everything can be resolved via iptables/ip route rules that I can't create. I've tried a dozen of "wizard manuals" and "howto's" to mix both solution but without success. Looking for an advice (and good reading links for networking begginers).

    Read the article

  • How to force mdadm to stop RAID5 array?

    - by lucek
    I have /dev/md127 RAID5 array that consisted of four drives. I managed to hot remove them from the array and currently /dev/md127 does not have any drives: cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid1 sdd1[0] sda1[1] 304052032 blocks super 1.2 [2/2] [UU] md1 : active raid0 sda5[1] sdd5[0] 16770048 blocks super 1.2 512k chunks md127 : active raid5 super 1.2 level 5, 512k chunk, algorithm 2 [4/0] [____] unused devices: <none> and mdadm --detail /dev/md127 /dev/md127: Version : 1.2 Creation Time : Thu Sep 6 10:39:57 2012 Raid Level : raid5 Array Size : 8790402048 (8383.18 GiB 9001.37 GB) Used Dev Size : 2930134016 (2794.39 GiB 3000.46 GB) Raid Devices : 4 Total Devices : 0 Persistence : Superblock is persistent Update Time : Fri Sep 7 17:19:47 2012 State : clean, FAILED Active Devices : 0 Working Devices : 0 Failed Devices : 0 Spare Devices : 0 Layout : left-symmetric Chunk Size : 512K Number Major Minor RaidDevice State 0 0 0 0 removed 1 0 0 1 removed 2 0 0 2 removed 3 0 0 3 removed I've tried to do mdadm --stop /dev/md127 but: mdadm --stop /dev/md127 mdadm: Cannot get exclusive access to /dev/md127:Perhaps a running process, mounted filesystem or active volume group? I made sure that it's unmounted, umount -l /dev/md127 and confirmed that it indeed is unmounted: umount /dev/md127 umount: /dev/md127: not mounted I've tried to zero superblock of each drive and I get (for each drive): mdadm --zero-superblock /dev/sde1 mdadm: Unrecognised md component device - /dev/sde1 Here's output of lsof|grep md127: lsof|grep md127 md127_rai 276 root cwd DIR 9,0 4096 2 / md127_rai 276 root rtd DIR 9,0 4096 2 / md127_rai 276 root txt unknown /proc/276/exe What else can I do? LVM is not even installed so it can't be a factor.

    Read the article

  • Display stretches 4:3 ratios; Adds scrolling to other ratios

    - by Matt
    I have a dual monitor setup. Normally, they both display at 1680x1050. They have been setup this way for about a year. I'm using Windows XP Professional 2003 x64 SP2. Today, out of nowhere, one of the monitors kicked back to a lower resolution. I was not playing with any configuration at the time.. in fact all I had done was close a window (maybe a browser). But the thing is that the resolution is still preserved partially by the fact that the screen will scroll when you move the mouse. So it's like looking through a 1024x768 window into a 1680x1050 world. The monitor itself does not appear to be damaged, because I also have it connected to my netbook (via KVM) and higher resolutions work fine. I tried uninstalling/reinstalling the drivers to no avail. System restore doesn't help either. I'm unsure of the exact ATI card I'm using.. Device Manager lists it as "Radeon X300/X550/X1050". There is no Catalyst Control Center software installed. I tried to install it, but there doesn't seem to be a way to install it by itself ... it forces you to install another driver, which breaks both of my displays, forcing me to go into safe mode and run system restore again. Any ideas? Thanks EDIT: After playing around more, I discovered that the "scrolling" behavior is only present for aspect ratios that are not 4:3. For 4:3 ratios, it just stretches out to fit the wide screen. My monitor's native ratio is 16:9 .. what could be causing it to think it needs to scroll?

    Read the article

  • Setting up virtualbox for outside access

    - by Morgan Green
    I have a computer running a server that my subdomain on my shared hosting account points to. IE subdomain.mydomain.org goes to my home server. Now then; what I'm wanting to do is be able to access my VirtualBox servers through that subdomain and a different port. E.G Ubuntu Virtual Box Server 1 Username:Ubuntuhost1 Password:MyUbuntuHost1 Port:4000 Internal IP: 192.168.1.60 External IP: 24.29.138.45 Ubuntu Virtual Box Server 2 Username:UbuntuHost2 Password:MyUbuntuHost2 Port:4001 Internal IP: 192.168.1.61 External IP: 24.29.138.45 Now I want to be able to access RDP number 1 through Port 4000, but if I access Port 4001 it will connect to the server on port 4001; both using the same subdomain. The next issue is the fact that even though I know what the IP addresses are on the router for the virtualbox hosts through ifconfig it doesn't change the fact that they don't show up on the router. If anyone knows how to configure this to work please help me out because I've been racking my brain to the highest extent I can. Alright; here's an edit to clarify more; Sorry. My ports on the router are edited to forward Port 4000 on Internal IP 192.168.1.63 (My Ubuntu Internal IP address) Now when I go to my Router Home Page my VirtualBox Internal IP Address doesn't show on the attached device listings, so I set up port forwarding anyways to the VirtualBox Internal IP. My end goal is when I connect to mydomain.org and I connect through port 3389 it takes me to my host computers server, but if I put in mydomain.org and go through port 4000 it's going to redirect to my VirtualBox server; Is this even possible? Sorry; I'm trying to clarify the most I think I can I just don't know how else to explain my issue.

    Read the article

  • Run a script on user connection on the VM host

    - by Scott Chamberlain
    I have a server running a Virtual Desktop Managed Pool, what I would like to do is when a user logs in I would like a script to check the number of available VMs and if below a threashold add additional VMs to the pool. The script to check the load and add to the pool is not the problem, I have that already figured out: $collectionName = "Test1"; $rdvh = "vmHost.example.com"; $minAvailableVMs = 2; Import-Module RemoteDesktop; $pool = Get-VirtualDesktopCollection -CollectionName $collectionName; $availableVMs = $pool.Size - ($pool.Size * $pool.PercentInUse / 100); $status = Get-VirtualDesktopCollectionJobStatus $collectionName #only add new servers if we are below the threashold and in the JOB_COMPLETEED state if($availableVMs -lt $minAvailableVMs -and $status.Status -eq [Microsoft.RemoteDesktopServices.Management.VirtualDesktopCollectionJobStatus]::JOB_COMPLETED) { Add-RDVirtualDesktopToCollection -CollectionName $collectionName -VirtualDesktopAllocation @{"$rdvh" = 1} } The problem I am having is, how do I run the above script on the Virtualization Host/Connection Broker/Some other server when a user connects?. I don't think it would be appropriate to run this as a logon script inside the VM, I think there is a way to do this on the management side but I don't know the new scripting interface in Server 2012 R2 well enough to know which commandlets I should look for to schedule this. EDIT: I know System Center is perfect for this but I do not have a license and was denied when I asked for it to be added to the budget.

    Read the article

  • Virtualize SBS 2003 - P2V vs migrating to new VM

    - by jlehtinen
    I need to virtualize a SBS 2003 server in my work environment. I need some tips on what people think is the best way to proceed. Background: The SBS 2003 server is the primary DC for the domain and also hosts FTP, RRAS(VPN), DNS, and file shares. Exchange is NOT used, neither is SQL server. DHCP is done via a firewall appliance. I have added a Server 2003 VM to the domain and promoted it to the DC role. AD/DNS is replicating here correctly. This was mainly done to provide fault-tolerance to the domain, I was not intending to make this VM the primary DC. I've already asked about buying upgraded licensing for Server 2008/2012 but was refused due to cost. Options: I see (at least) two routes I could take to complete this. From what I've read option 2 is the "preferred" method, but there's a few steps where I'm not clear on what to expect. Option 1.) P2V the primary DC Power off primary DC Power off secondary DC (to prevent USN rollback in case P2V has issue) P2V (cold clone) primary DC Boot new PDC VM Allow new hardware to detect Remove old NIC hardware from device manager Assign old IPs to new virtual NICs Reboot PDC VM, confirm connectivity and no major issues Power on secondary DC, confirm replication Option 2.) Create new VM, transfer roles, remove original DC from domain Create new VM, install SBS 2003 Do I need the original SBS install discs for this? MS migration doc mentions this. Add VM to domain, promote to DC role Does this start 7 day timer where two SBS servers can be in same domain? Set up RRAS on new VM Set up IIS/FTP on new VM Move file shares to new VM Transfer FSMO roles to new VM DC dcpromo original primary DC out of domain

    Read the article

  • USB Harddisk not working on dual boot windows7/8

    - by Jesper
    Yesterday I installed Windows 8 on a machine that already had Windows 7. They are on dual boot and both systems work fine. The problem is that inserting a USB hard disk in either system does nothing. If I connect a USB mouse or mobile phone, they work fine, so the USB plugs are active/working and the USB hard drives that I am trying to connect work on my other laptop just fine. I have tried to uninstall all USB-related items in Device Manager and let them reinstall upon restart, but that didn't help. The USB drive does not show up in disk management either. The strange thing is that it is exactly the same situation on both windows. USB mice etc. work just fine and USB hard drives do not. Any ideas on solving this problem would be great. ...Don't know if it is important, but this is a Toshiba Tecra R950 Laptop. EDIT: I have found out that my other USB HD (Western Digital) works on this laptop, but for my StoreJet Transcend and Adata "something" does not work. All three work on another Windows 7 laptop. Sizewise the WD is in the middle at 400 GB. The StoreJet is 640 GB and the Adata is 200 GB.

    Read the article

  • Does anyone know how to "tcpdump" traffic decrypted by Mallory MITM? [migrated]

    - by chriv
    I'm looking for some help in capturing network traffic that I can analyze in Wireshare (or other tools). The tool I'm using is mallory. If anyone is familiar with mallory, I could use some help. I've got it configured and running correctly, but I don't know how to get the output that I want. The setup is on my private network. I have a VM (running Ubuntu 12.04 - precise) with two NICs: eth0 is on my "real" network eth1 is only on my "fake" network, and is using dnsmasq (for DNS and DHCP for other devices on the "fake" network) Effectively eth0 is the "WAN" on my VM, and eth1 is the "LAN" on my VM. I've setup mallory and iptables to intercept, decrypt, encrypt and rewrite all traffic coming in on destination port 443 on eth1. On the device I want intercepted, I have imported the ca.cer that mallory generated as a trusted root certificate. I need to analyze some strange behavior in the HTTPS stream between the client and server, so that's why mallory is setup in between for this MITM. I would like to take the decrypted HTTPS traffic and dump it to either a logfile or a socket in a format compatible with tcpdump/wireshark (so I can collect it later and analyze it). Running tcpdump on eth1 is too soon (it's encrypted), and running tcpdump on eth2 is too late (it's been re-encrypted). Is there a way to make mallory "tcpdump" the decrypted traffic (in both directions)?

    Read the article

  • DRBD stacked resources: recovering from failure

    - by Marcus Downing
    We're running a stacked four-node DRBD setup like this: A --> B | | v v C D This means three DRBD resources running across these four servers. Servers A and B are Xen hosts running VMs, while servers C and D are for backups. A is in the same datacentre as C. From server A to server C, in the first datacentre, using protocol B From server B to server D, in the second datacentre, using protocol B From server A to server B, different datacentres, stacked resource using protocol A First question: booting a stacked resource We haven't got any vital data running on this setup yet - we're still making sure it works first. This means simulating power cuts, network outages etc and seeing what steps we need to recover. When we pull the power out of server A, both resources go down; it attempts to bring them back up at next boot. However, it only succeeds at bringing up the lower-level resource, A-C. The stacked resource A-B doesn't even try to connect, presumably because it can't find the device until it's a connected primary on the lower level. So if anything goes wrong we need to manually log in and bring that resource up, then start the virtual machine on top of it. Second question: setting the primary of a stacked resource Our lower-level resources are configured so that the right one is considered primary: resource test-AC { on A { ... } on C { ... } startup { become-primary-on A; } } But I don't see any way to do the same with a stacked resource, as the following isn't a valid config: resource test-AB { stacked-on-top-of test-AC { ... } stacked-on-top-of test-BD { ... } startup { become-primary-on test-AC; } } This too means that recovering from a failure requires manual intervention. Is there no way to set the automatic primary for a stacked resource?

    Read the article

  • Wifi antenna extension with F-connector/RG-6(RG-59) cable?

    - by rjz2000
    In an older house, the wire mesh in walls surrounding the furnace behave like a Faraday cage and block wifi signals. It is also difficult to lay new cable, however there is television cable to multiple locations due to there once having been a roof-installed, television antenna. It would be relatively trivial to install the wifi router at the center distribution point, then have the antenna broadcasting/receiving the signal plugged in at each of the old television outlets. I assume that it would not be too difficult to find an adapter for SMA <- F-type connectors. The cable is actually RG-59 rather than RG-6, but I assume that it still has relatively good RF isolation along its length, which is no more than a couple hundred feet in any direction. Does anyone know a problem with the idea? Will a router get confused if there is /too little/ interference between the two antenna? Is that length of cable (~100ft) too long for the signal a router broadcasts? I have seen that it is also possible to use old ~$30/each FiOS cable modems available on eBay to extend a network over television cable. However, that seems like a less elegant solution, and might interfere with upnp and dlna services I'd like to have work on a single network. Thanks if anyone has answers or suggestions before I try this project!

    Read the article

  • Wifi antenna extension with F-connector/RG-6(RG-59) cable?

    - by rjz2000
    In an older house, the wire mesh in walls surrounding the furnace behave like a Faraday cage and block wifi signals. It is also difficult to lay new cable, however there is television cable to multiple locations due to there once having been a roof-installed, television antenna. It would be relatively trivial to install the wifi router at the center distribution point, then have the antenna broadcasting/receiving the signal plugged in at each of the old television outlets. I assume that it would not be too difficult to find an adapter for SMA <- F-type connectors. The cable is actually RG-59 rather than RG-6, but I assume that it still has relatively good RF isolation along its length, which is no more than a couple hundred feet in any direction. Does anyone know a problem with the idea? Will a router get confused if there is /too little/ interference between the two antenna? Is that length of cable (~100ft) too long for the signal a router broadcasts? I have seen that it is also possible to use old ~$30/each FiOS cable modems available on eBay to extend a network over television cable. However, that seems like a less elegant solution, and might interfere with upnp and dlna services I'd like to have work on a single network. Thanks if anyone has answers or suggestions before I try this project!

    Read the article

  • Quicktime won't install on Windows 7 Ultimate 64bit

    - by Martin
    Hi! I am trying to install quicktime (actually just need iTunes..but then iTunes needs qt), but it fails. There seems to be a problem with the folder C:\Program Files(x86)\QuickTime\ - Quick Time wants to write the file QTTask.exe, but complains that it does not have permission to do so. Same thing happens with \PropertyPanels\PanelHelperBase.qpa I have tried deleting all Apple programs (in the order suggested in the support forum) and also tried to delete the temp folder. That did not work. I have tried to manually adjust the permissions of the QuickTime folder - no effect. I have run the installation file with admin rights and with different compatibility modes to no effect. I consider myself to be an experienced user - able to solve most problems - but now I am stuck. I need some input / fresh ideas on how to tackle the problem. This is very annoying as I cannot sync iPhone/iPad/iPod while iTunes is not running - due to the stupid (sorry) idea of only have your device linked to one library. Please help. Thanks!

    Read the article

  • How do I determine how future-proof and stable a router is?

    - by Aarthi
    I mentioned in my last question that my wireless router had a bad habit of crashing. After consulting with the Super User chatroom, as well as my sysadmin, I've decided I may as well purchase a new router. However, I'm unsure how to evaluate all these tech specs that get touted about. The two things that seem to be the most important to me are: (1) keeping my router future-proof (as standards evolve and change), and (2) ensuring its stability. Unfortunately, I'm not sure what, exactly, I should be looking for in the tech specs or the item description that can give me a good idea of how stable or future-proof my decide will be. What should I look for? Can I determine stability without having to try the device out myself? Please note: I'm not a battle-hardened power user by any means, so I'll likely be reliant on the given firmware for my router. My last router lasted me like four years, so I mostly just want something that'll cover a 500 sqft apartment in New York with minimal crashing, so that I can watch Hulu in peace. And make Skype calls. If it helps, the router models that I'm currently decided between are this ASUS one and this LinkSys one.

    Read the article

  • How to setup firewall to allow internet connection sharing via Wifi USB stick?

    - by hannanaha
    I have a Windows8 computer linked to the internet via an ethernet cable ("Ethernet" network connection). I have attached to it a DLink Wifi USB stick, and I'm trying to share the main PC's internet connection with my Android phone via a local wifi network. I am using the following batch file to set up this network: netsh wlan set hostednetwork mode=allow ssid=MyWifiName key=password keyUsage=persistent netsh wlan start hostednetwork After I run this script, I can see a new network connection appear in "Control Panel\Network and Internet\Network Connections" named "Local Area Connection *12", and I can see "MyWifiName" on the Android phone. The device name for this connection on the PC is "Microsoft Hosted Network Virtual Adapter". I also set up the "Ethernet" connection to share Internet with "Local Area Connection *12". However, the Android phone usually doesn't manage to obtain an IP from the wireless network, and when it does, there still seems to be no connectivity to the internet. When I turn off the Windows Firewall completely, or even just for "Local Area Connection *12", the Android connection is perfect. My questions are: How should I set up the Windows firewall to allow the phone to connect properly? Is there a specific rule I need to add to the Windows firewall advanced settings? [Note: the above method worked great in Windows 7, without any specific tinkering with the firewall]. Is it safe to turn off the firewall specifically for the "Local Area Connection *12" (the wifi connection) if the main Ethernet connection is still protected by the firewall? Thanks in advance.

    Read the article

  • Hard crash when using bluetooth headset on MacBook Pro and Lion 10.7.2

    - by jtalarico
    I recently picked up a bluetooth headset (Motorola S10-HD) and started using it with my MacBook Pro (17" purchased new in 2010) running Lion 10.7.2. Here's what works - stereo audio: iTunes Spotify Pandora (via browser) games (e.g. Minecraft, which is a Java app) audio from YouTube Plex, VLC, other video players Here's what doesn't work well - stereo audio fails and the headset seems to go into mono (i.e. tinny-as-hell) mode: Google Hangout Skype GoTo Meeting Here's what's just downright catastrophic. If I'm listening to stereo audio and then decide to jump into a Skype call (Google Hangout, or GoTo Meeting), bluetooth often crashes and I can only get things working again by shutting down the device, disabling bluetooth, and getting things back up and running again. But the audio is still horrible, and MUCH better using just a simple set of iPhone earbuds and mic. About 80% of the time during such a call, bluetooth crashes. And about 90% of the time, after the call ends, Skype is shut down, or I try to switch back to playing stereo audio, I get a hard crash!! The gray screen of death descends and I'm told I need to restart my machine. In one such instance, even after a reboot, I could not enable bluetooth again ("Turn Bluetooth On" was grayed out in taskbar). Is this just a weak implementation of bluetooth by Apple, or is this a hardware issue? I've seen others posting similar issues even on the Apple support site indicating that bluetooth headsets are failing left and right, but I haven't seen anyone mention hard crashes.

    Read the article

  • Replace Linux Boot-Drive | ext3 to btrfs

    - by bardiir
    I've got a headless server running Debian Linux currently. Linux vault 3.2.0-3-686-pae #1 SMP Mon Jul 23 03:50:34 UTC 2012 i686 GNU/Linux The root filesystem is located on an ext3 partition on the main harddrive. My data is located on multiple harddrives that are bundled to a storage pool running with btrfs. UUID=072a7fce-bfea-46fa-923f-4fb0827ae428 / ext3 errors=remount-ro 0 1 UUID=b50965f1-a2e1-443f-876f-578b5f93cbf1 none swap sw 0 0 UUID=881e3ad9-31c4-4296-ae60-eae6c98ea45f none swap sw 0 0 UUID=30d8ae34-e2f0-44b4-bbcc-22d761a128f6 /data btrfs defaults,compress,autodefrag 0 0 What I'd like to do is to place / into the btrfs pool too. The ideal solution would provide the flexibility to boot from any disk in the system alike, so if the main drive fails I'd just need to swap another one into the main slot and it would be bootable like the main one. My main problem is, everything I do needs to result in a bootable system that is open to ssh logins via network as this server is 100% headless so there is no possibility to boot it from a live cd or anything like that. So I'd like to be extra sure everything works out fine :) How would I best go about this? Can anybody hint me to guides or whip something up for these tasks? Anything I forgot to think about? Copy root-data into btrfs pool, adjust mountpoints,... Adjust GRUB to boot from btrfs pool UUID or the local device where GRUB is installed Sync GRUB to all harddrives so every drive is equally bootable (is this even possible without destroying the btrfs partitions on the drives or would I need to disconnect the drives, install grub on them and then connect them back with a slightly smaller partition?)

    Read the article

  • Good Enough Failover Strategy for DNS / MySQL / Email

    - by IMB
    I've asked and read a lot questions regarding DNS failover but the more I read the more complicated it becomes, some people say it's good enough some say it isn't. No clear answers from what I read. I was wondering if we can set it straight once and for all, at least for the requirements of most websites out there. Right now let's assume the following: We don't need really need load-balancing, what we need is a failover solution. We are running a website based on LAMP on a VPS. We need to make sure that the Web Server, MySQL, Email are always accessible if not 99%. Basically here's my idea and questions about it: Web Server: We need at least one failover server (another VPS on a separate data center). Is DNS Failover via Round Robin good, if not, what's the best? And how do you exactly implement it? How do you make the files you upload/delete on Server A is also on Server B? MySQL: I've only read a brief intro to MySQL replication and I assume that I can replicate Server A to Server B and vice versa on the fly right? So just it case Server A fails and Server B is now running, it will continue to work and replicate to Server A when it becomes available. So in essence Server B is now the primary server, and will later on failover to Server A, should a failure happen again. Email: If we are gonna use DNS Failover, using webmail or relying on emails stored on the server is probably not a good idea right? Since some emails might be on Server A while some might be on Server B? I assume a basic email forwarder to a 3rdparty is good enough (like Gmail for example) to ensure all emails are kept in one place. Here's a basic diagram for a better picture: http://i.stack.imgur.com/KWSIi.png

    Read the article

  • Windows 8.1 in a VMWare Workstation 10 guest's mouse is missing, but only sometimes

    - by Rob Perkins
    I have VMWare Workstation 10 running on a Windows 7 machine, hosting a k guest OS. Before upgrading to WS 10 I was using version 9, and the Win8 guest OS ran without difficulty or error conditions. Since upgrading and installing the most current VMWare Tools inside the guest after upgrading to version 10, there are circumstances where the mouse pointer is not visible; the mouse position appears stuck at a screen location which is not the center of the virtualized display; and mouse click and scrolling events still get processed. Once this begins happening I have to reboot the host machine to get it to stop. (VMWare Tools 9.6.1 build-1378637 is what the WS 10 software installed) The problem seems to correlate with whether the mouse is captured during Win 8.1's bootup process, before control is passed to the login screen. If I explicitly click the mouse into the guest OS and move it slowly around while the system is booting, then I see the mouse after clicking to lift the first screen and expose the password prompt, and there is never a problem within the guest. If I don't do this during bootup, there is no mouse pointer, with the symptoms listed above. I have tried removing and reinstalling VMWare tools, and the other steps published for "mouse problems" from VMWare's chaotic troubleshooting database. The problem persists. Is there a setting in the virtual machine's configuration which could prevent this behavior?

    Read the article

  • For Windows XP: How to uninstall Broadcom Bluetooth software that won't disappear

    - by T. Webster
    Hello, my situation is similar to this question for Windows 7, except my OS is Windows XP SP3. I have recently realized I made the mistake of buying a Bluetooth adapter and installing the Broadcom/Widcomm Bluetooth stack driver software. Now that I know that the software is no good, I want to install it (so I can install the Toshiba stack for the Cirago adapter). I've attempted to uninstall all Bluetooth driver software in Device Manager, and I don't see any remnants of any Bluetooth drivers there. I would include pictures here, but I don't have 10 reputation yet, so I'll just use links instead. picasaweb.google.com/lh/photo/2NAos6BP9UigPtJKaYRGyQ?feat=directlink But I do see that the little Bluetooth icon still persists: picasaweb.google.com/lh/photo/kbxgPP8ZLxhjX4ob2YjSew?feat=directlink I don't see anything about Bluetooth, Broadcom, or Widcomm in Add/Remove Programs. I don't see any folder names Broadcom or Widcomm in Program Files folder, either. But I do see that Broadcom does show up in the registry with respect to Bluetooth, as shown here. picasaweb.google.com/lh/photo/hWDo-OzB8ApibzeHA_saxQ?feat=directlink What should I do now to completely wipe this persistent Broadcom Bluetooth software off my computer?

    Read the article

  • Installing Ubuntu guest crashes Hyper-V host

    - by Grant
    I have a weird problem that I don't even know where to begin diagnosing. Trying to install Ubuntu to a VM locks up the host system! My setup is: Dell R715 server, dual 16 core AMD opteron processors, 96GB RAM Dell MD3600f SAN Server 2008 R2 Datacenter System Center VMM 2012 There are 5 windows virtual machines running that have had no problems. This is the first linux VM I've tried to create. I setup a VM through virtual machine manager, set the CD drive to a Ubuntu 12.04 server x64 iso, and started it up. It boots up the normal ubuntu install menu, but the second I hit enter on "Install Ubuntu Server", I get disconnected. The HOST machine stops responding to pings. So do all virtual machines on it. It locks up entirely - keyboard on the host won't work, mouse won't move, numlock light won't change. There's no blue screen - the host is sitting at the login screen completely unresponsive. I can't find any relevant logs in event viewer after rebooting. What could cause the host machine to freeze like that? It's not a one time occurrence - it happens every time at the exact same point. Thank god this server isn't in production yet!

    Read the article

  • Ubuntu 12.10 64bit host reboots when trying to install any guest system using VirtualBox

    - by gts123
    I am having a really nasty problem with VirtualBox as everytime I try to install any guest OS(using ISO file as CD for installation media), the installation starts normally but as soon as it is about to start either installing to virtual hard drive or loading(e.g. as LiveFS) it causes the host system to reboot abruptly. Config is as below: Host system: Ubuntu 12.10 64bit - Intel® Core i7-2640M CPU @ 2.80GHz × 4 Virtualbox version: 4.1.18_Ubuntu r78361 Guest OS systems tried: 32bit version of FreeBSD 9, Debian 6, Tails 0.14 VM setup Tried to have the minimal setup necessary just in case it would avoid for each system to make sure I'd avoid conflicts, but to no avail. I've tried different values and combinations of the below but the problem still persists: Shared Clipboard: Disabled Show in fullscreen/seamless: Disabled Remember runtime changes: DIsabled Base Memory: 2048 MB Chipset: PIIX3 IO APIC: Disabled EFI: Disabled Absolute Pointing device: Disabled Processor(s): 1 CPU PAE/NX: Disabled VT-x/AMD-V: Disabled Video Memory: 12 MB 3d/2d acceleration: Disabled Storage IDE COntroller: PIIX3 (same as chipset instead of PIIX4) Use host I/O cache: No Audio: disabled Network adapter: NAT USB controller: disabled No shared folder Also another sideeffect of the reboot is that it appears that it does not log any information in the error log files; not making things any easier. Please help.

    Read the article

  • Switching from Onboard intel to Nvidia Dedicated GPU

    - by Anarkie
    How can I switch from Intel onboard grpahics to Nvidia Dedicated GPU? When I go to windows screen resolution I see intel. I cant change it. I go to Device Manager, I see both Adapters are there and Nvidia is known.I disabled intel, I didnt see any option to set one as primary so I disabled intel, black screen!Reboot and re-enable intel. I right click on the desktop, choose "Nvidia Control Panel" and on 3D options I chose the desired game I want to play, High performance Nvidia, but it didnt switch when I started the game. Then I made preferred GPU in the global settings High performance Nvidia for everything it still didnt change.I understand to save the battery etc. there is a switch option between these two but I dont see this switch when it is necessary, I cant also switch manually?Is there a manual switch FN key?I looked but couldnt find. Why I want to do this? 1) Better game peformance. 2) I want to play an old game from 2002(Diablo 2 LOD), when I start the game there are black bars on the sides, so screen becomes just smaller which I dislike!I heard this is intel's specification to center the display.But instead I would like to scale or expand it to fit widescreen(fullscreen).Which should be possible with Nvidia. My Notebook Specs: Fujitsu Lifebook AH531, Win7 , 64 bit, i5, intel HD graphics onboard, Nvidia GT 525. I didnt install Nvidia later, it was always installed and ready from the moment I turned on the computer first time. How I determined that the cards werent switched when I am playing the game: with the windows key I exited from the game, then looked at screen resolutions menu, still saw intel, also the game was still with black bars.I know intel GPU should enough for Diablo 2 but I am interested in this answer for further games, I dont always play Diablo, what if I install an up to date game for example?Then Intel will not be sufficient.I would like to learn the switch option.

    Read the article

< Previous Page | 543 544 545 546 547 548 549 550 551 552 553 554  | Next Page >