Search Results

Search found 14816 results on 593 pages for 'logical model'.

Page 549/593 | < Previous Page | 545 546 547 548 549 550 551 552 553 554 555 556  | Next Page >

• Troubleshooting major performance issue: Is culprit Intel RST, Hard drive, or something else?

  - by Sean Killeen

  The Setup I have the following components that come into play in this situation: ASUS P8Z68 V/PRO motherboard a RAID1 configuration (1x 1TB drive, 1 x 2TB drive -- I explain below), accelerated with an SSD using Intel's RST software, and 1 TB drive standing by as a spare. Core i7 2600k 32 GB RAM Windows 8.1 This box was designed to be beast, and until just recently, was very good at being just that. What's Happening The system has slowed to a crawl whenever it touches the disk. Things appear to work at normal speed when dealing with memory. For example, typing this is fine, but saving it to disk from notepad gave me a 5-7 second pause when clicking save. The disks appear to be at 100% all the time (e.g. the light on the disk access on the PC is solidly on -- not even any flashing) In ProcExp it appears that the disk is barely being utilized at all: Intel RST reports that everything is fine: Other Details Prior to this happening, RST had reported that my drives were failing (one went bad, one was throwing SMART events). This made sense; they were at the tail end of their warranty and the PC is on almost all the time. I RMA'd the drives via Seagate. In the meantime, I'd purchased a 2TB drive because I didn't realize that the 1TB drives were under warranty. I figured I'd replace the other 1 TB drive with another 2 TB when it died but then discovered the warranty. AFAIK, I haven't done any major updates since 8.1 and it worked fine after those. Question(s) How can I troubleshoot this? What is the best way to try to figure out why disks are being maxed out despite the OS reporting barely any disk usage and that everything is OK? Given the failures, etc. that I describe above, is it possible that the problem could be the I/O on the motherboard itself? If so, how would I even be able to diagnose it? I'm betting the drives that Seagate gave me are refurbished (didn't think to look; that's dumb). Is it possible that the same model drive, refurbished, could somehow cause this? In terms of how RAID1 works, is it possible that one drive is "falling behind" somehow, and that the RAID1 is constantly trying to fix the mirroring? If so, this seems like Intel RST would report on it, but I wanted to consider it as an option.

  Read the article

• Critique My Backup and Storage Plan

  - by MetaHyperBolic

  My current storage (RAID-1 off of a hardware RAID card) and backup (a spare drive) solutions for my home network are inadequate. I have too much data scattered on various one-off drives. It is time to evolve. Backups seem simple enough, at least: lots of big drives. However, I am bewildered by the number of choices for small home storage. The Drobo S looks appealing. So does the ReadyNAS. I am not looking for bunches of shiny features, I'm mostly interested in reliability. I am not interested in building Yet Another PC to create a file server or doing something in the cloud, or whatever. I'm stupid, so I am keeping it simple. Requirements for Main Volume: Starting working space roughly 2TB, with options for growth up to 5TB RAID or something RAID-like with at least one parity drive eSATA II for speed during backups Ability to shut down gracefully when alerted of low power by a UPS Optional but Desirable: Will take 2TB drives now with options for the larger 3TB drives coming in 2010-2011 Optional but Desirable: : RAID-6 or something similar, with two parity drives Optional but Desirable: : Hot spare Ethernet connection not required, as the volume will be shared via the same machines which runs my home print server Backups: Backup performed via ROBOCOPY in mirror mode to an external hard drive via a eSATA II connection. Start with rotating between two external 2TB hard drives, will go up to six external 2TB drives. Start with a weekly backup, move to a bi-weekly backup as more drives are added. Move to 3TB drives as the size of my main volume increases. Backup drives will be stored on an off-site location. Hard drives: I plan on buying all of the same model, but different batches from different vendors. I found a "burn-in" utility with which I can pound away on the drives for a couple of weeks before adding them to the backup pool or the main volume. I estimate that I am looking at roughly $1,500 to start, once I start throwing in two TB drives for backup and four for storage. So, are there any obvious flaws in my plan? What have I overlooked? Any suggestions for the storage device for my main volume that fits my requirements? Or do I just keep it simple, 2 drives in RAID-1, then perform due diligence with my backups, accepting that I will have to buy a whole new unit when my data grows past 2TB?

  Read the article

• Why does Process Explorer cause highly targeted failure of some applications / basic UI functions in a high-power EC2 Windows instance?

  - by Dan Nissenbaum

  Update: I have determined that Process Explorer itself - the program I am using to debug a performance issue - seems to be the cause of the issue. See note, with updated question, at end. I am running a high-power (cc2.8xlarge) Amazon AWS EC2 Windows instance off of a boot EBS volume, provisioned at 2500 PIOPS, which was created from a snapshot of a previous boot volume. My purpose with the instance is to use it as a development workstation with many developer tools installed, such as Visual Studio, a local XAMPP stack, etc. I have upwards of 40 programs installed on the machine. The usability of the instance as a development machine often works quite well. The RDP lag is adequately small. I have used it for hours on end without problems for some of my most intense development tasks. As a result, I have just purchased a reserved instance, and I opted to rebuild my development machine starting from scratch with a Windows Server 2012 AMI. After having installed all of my desired/required applications for development over this past week, again the machine seems to often work well and I have worked for up to an hour at a time without problems doing heavy development work. However, I continue to run into catastrophic OS usability issues that may prevent me from being able to rely on this machine as a development machine. I would like to track down the source of the problem, if there is an easily identifiable source. (Update: I have tracked down the source to be Process Explorer, the very program I was using to debug the problem. See update at end.) The issues are as follows. (These are some primary examples) Some applications, after a period of adequate responsiveness, suddenly begin to respond very, very slowly to basic user interface actions such as clicking on menus and pressing Ctrl-Tab to switch between open documents. Two examples are UltraEdit and PhpEd. It typically takes ~2 seconds for a menu to appear, and ~4 seconds to switch between open documents. Additionally, insertion point motion in the editor is lagged by upwards of ~2 seconds. Process Explorer, which I am using to help debug the problem, seems to run acceptably for a couple of minutes, but on multiple occasions Process Explorer itself hangs completely. It hangs at the same time as the problems noted above. When it hangs, it is 100% unresponsive. Clicking on its taskbar icon neither causes it to come to the top or go behind, and its viewable area is filled with nothing but a region partially containing pure white and partially containing incomplete windows widgets that are unreadable, and that never change. Waiting 10 minutes does not clear the problem. Attempting to force-quit Process Explorer by right-clicking on its taskbar icon and choosing "Close Window" takes about 5 full minutes to exit (Process Explorer itself can't be used to exit Process Explorer, and it is registered as a Task Manager substitute). Other programs work just fine during this time. For example, Chrome tabs flip very quickly back and forth, menus pop open instantly, web pages load quickly, and typing in forms/web applications inside the browser works promptly. Another example of an application that works crisply is Filemaker - its menus open instantly, and switching views in this application occurs promptly. Other applications also work without issue. Also, switching between applications occurs promptly as well. It is only a handful of applications that exhibit the problem, with some primary examples given above. At first I thought that EBS IOPS might be a problem. Therefore, I ran Performance Monitor, and watched the "Disk Transfers/sec" monitor in real time. At no point did this measure come anywhere close to hitting the 2500 PIOPS provisioned for the EBS volume. The RAM was also well under the limit (~10 GB used out of 60 GB). I did notice that one CPU core (out of 32 logical cores) was fully thrashing at 100% (i.e., ~3.1%) during the problematic periods. This seems to indicate that a single CPU core is handling the menus / flipping between open documents (for some applications only) / managing the Process Explorer user interface, and that this single core was hosed for some reason during the problematic periods. Also note that I have a desktop workstation (Windows 7) that I also use as a development machine, via a remote connection, with a nearly identical set of programs installed, and this desktop workstation does not exhibit any of the problems I've discussed above. I have been using it heavily for well over a year now. Any suggestions regarding either the source of the problem, or steps I might take to investigate the source of the problem, would be appreciated. Thanks. Note: After extensive testing & investigation, I have noticed that when I quit Process Explorer, the problem vanishes and the system performance returns to normal, and then reappears quickly when I run Process Explorer again (note: again, the performance problems only appear for a subset of applications - other applications work perfectly fine during the same period). My question is therefore (thankfully) more specific: Why does Process Explorer cause highly targeted failure of some applications (including itself) and basic UI functions, in a high-power EC2 Windows instance?

  Read the article

• Does a router have a receiving range?

  - by Aadit M Shah

  So my dad bought a TP-Link router (Model No. TL-WA7510N) which apparently has a transmitting range of 1km; and he believes that it also has a receiving range of 1km. So he's arguing with me that the router (which is a trans-receiver) can communicate with any device in the range of 1km whether or not that device has a transmitting range of 1km. To put it graphically: +----+ 1km +----+ | |------------------------------------------------->| | | TR | | TR | | | <----| | +----+ 100m+----+ So here's the problem: The two devices are 1km apart. The first device has a transmitting range of 1km. The second device only has a transmitting range of 100m. According to my dad the two devices can talk to each other. He says that the first device has a transmitting and a receiving range of 1km which means that it can both send data to devices 1km away and receive data from devices 1km away. To me this makes no sense. If the second device can only send data to devices 100m away then how can the first device catch the transmission? He further argues that for bidirectional communication both the sender and the reciver should have overlapping areas of transmission: According to him if two devices have an overlapping area of transmission then they can communicate. Here neither device has enough transmission power to reach the other. However they have enough receiving power to capture the transmission. Obviously this makes absolutely no sense to me. How can a device sense a transmission which hasn't even reached it yet and go out, capture it and bring it back it. To me a trans-receiver only has a transmission power. It has zero receiving power. Hence for two devices to be able to communicate bidirectionally, the diagram should look like: Hence, from my point of view, both the devices should have a transmission range far enough to reach the other for bidirectional communication to be possible; but no matter how much I try to explain to my dad he adamantly disagrees. So, to put an end to this debate once and for all, who is correct? Is there even such a thing as a receiving range? Can a device fetch a transmission that would otherwise never reach it? I would like a canonical answer on this.

  Read the article

• SAS Expanders vs Direct Attached (SAS)?

  - by jemmille

  I have a storage unit with 2 backplanes. One backplane holds 24 disks, one backplane holds 12 disks. Each backplane is independently connected to a SFF-8087 port (4 channel/12Gbit) to the raid card. Here is where my question really comes in. Can or how easily can a backplane be overloaded? All the disks in the machine are WD RE4 WD1003FBYX (black) drives that have average writes at 115MB/sec and average read of 125 MB/sec I know things would vary based on the raid or filesystem we put on top of that but it seems to be that a 24 disk backplane with only one SFF-8087 connector should be able to overload the bus to a point that might actually slow it down? Based on my math, if I had a RAID0 across all 24 disks and asked for a large file, I should, in theory should get 24*115 MB/sec wich translates to 22.08 GBit/sec of total throughput. Either I'm confused or this backplane is horribly designed, at least in a perfomance environment. I'm looking at switching to a model where each drive has it's own channel from the backplane (and new HBA's or raid card). EDIT: more details We have used both pure linux (centos), open solaris, software raid, hardware raid, EXT3/4, ZFS. Here are some examples using bonnie++ 4 Disk RAID-0, ZFS WRITE CPU RE-WRITE CPU READ CPU RND-SEEKS 194MB/s 19% 92MB/s 11% 200MB/s 8% 310/sec 194MB/s 19% 93MB/s 11% 201MB/s 8% 312/sec --------- ---- --------- ---- --------- ---- --------- 389MB/s 19% 186MB/s 11% 402MB/s 8% 311/sec 8 Disk RAID-0, ZFS WRITE CPU RE-WRITE CPU READ CPU RND-SEEKS 324MB/s 32% 164MB/s 19% 346MB/s 13% 466/sec 324MB/s 32% 164MB/s 19% 348MB/s 14% 465/sec --------- ---- --------- ---- --------- ---- --------- 648MB/s 32% 328MB/s 19% 694MB/s 13% 465/sec 12 Disk RAID-0, ZFS WRITE CPU RE-WRITE CPU READ CPU RND-SEEKS 377MB/s 38% 191MB/s 22% 429MB/s 17% 537/sec 376MB/s 38% 191MB/s 22% 427MB/s 17% 546/sec --------- ---- --------- ---- --------- ---- --------- 753MB/s 38% 382MB/s 22% 857MB/s 17% 541/sec Now 16 Disk RAID-0, it's gets interesting WRITE CPU RE-WRITE CPU READ CPU RND-SEEKS 359MB/s 34% 186MB/s 22% 407MB/s 18% 1397/sec 358MB/s 33% 186MB/s 22% 407MB/s 18% 1340/sec --------- ---- --------- ---- --------- ---- --------- 717MB/s 33% 373MB/s 22% 814MB/s 18% 1368/sec 20 Disk RAID-0, ZFS WRITE CPU RE-WRITE CPU READ CPU RND-SEEKS 371MB/s 37% 188MB/s 22% 450MB/s 19% 775/sec 370MB/s 37% 188MB/s 22% 447MB/s 19% 797/sec --------- ---- --------- ---- --------- ---- --------- 741MB/s 37% 376MB/s 22% 898MB/s 19% 786/sec 24 Disk RAID-1, ZFS WRITE CPU RE-WRITE CPU READ CPU RND-SEEKS 347MB/s 34% 193MB/s 22% 447MB/s 19% 907/sec 347MB/s 34% 192MB/s 23% 446MB/s 19% 933/sec --------- ---- --------- ---- --------- ---- --------- 694MB/s 34% 386MB/s 22% 894MB/s 19% 920/sec 28 Disk RAID-0, ZFS 32 Disk RAID-0, ZFS 36 Disk RAID-0, ZFS More details: Here is the exact unit: http://www.supermicro.com/products/chassis/4U/847/SC847E1-R1400U.cfm

  Read the article

• Microphones not working on Apple macbook Air 1,1 (Early 2008) under Linux

  - by jj_p

  I'm running Linux on an mba. I can't make the microphones (neither external nor internal) work. I test using alsamixer and arecord -d 5 test-mic.waw together with aplay test-mic.waw It seems there is a problem with kernel trying to decipher Apple (intentionally) corrupted 'bios', in particular the mic pins are wrongly assigned. As far as we are concerned here, is there any difference between using EFI and BIOS-compatibility mode? (see https://wiki.archlinux.org/index.php/MacBook where they claim to have everything working out of the box on mba1,1) A nice proposal would be to compile the latest Linux kernel and run hda-jack-retask to find the right configuration (in the case of Realtek codec, the missing things I'm supposed to check are either some vendor-specific COEF verbs, EAPD or GPIO setup.), and then come up with a kernel patch to address the issue. Since I'm not that familiar with this last part of the story, can anyone help me through this process? Some useful data: The output from alsa script run as root http://www.alsa-project.org/db/?f=adae8ebee1007043fe83414ac4972319e02255fa The command hda-jack-sense-test -a (with external mic in) Pin 0x14 (Internal Speaker): present = No Pin 0x15 (Green HP Out): present = Yes Pin 0x16 (Not connected): present = No Pin 0x17 (Not connected): present = No Pin 0x18 (Not connected): present = No Pin 0x19 (Not connected): present = No Pin 0x1a (Not connected): present = No Pin 0x1b (Not connected): present = No Pin 0x1c (Not connected): present = No Pin 0x1d (Not connected): present = No Pin 0x1e (Not connected): present = No Pin 0x1f (Not connected): present = No Most likely the chip is Realtek ALC885 (compare also ALC889A) http://guide-images.ifixit.net/igi/bBTSqaeK5JpQ1AWe.large , although at the moment alsa reads it as ALC889A Takashi Iwai's tutorial https://www.kernel.org/doc/Documentation/sound/alsa/HD-Audio.txt Some people researched the original files from a running OS X installation on this same model (I think the relevant files are AppleHDA.kext/Contents/MacOS/AppleHDA AppleHDA.kext/Contents/PlugIns/AppleHDAHardwareConfigDriver.kext/Contents/Info.p????list AppleHDA.kext/Contents/Resources/layout12.xml.zlib AppleHDA.kext/Contents/Resources/Platforms.xml.zlib) http://www.insanelymac.com/forum/topic/220090-alc889a-pin-configuration/#entry1554954 Datasheet http://www.realtek.info/pdf/ALC885_1-1.pdf (from the same Realtek, one can also try to download Linux driver, but this is just taken from ALSA project, as stated in the readme file.) Compare with this Arch guy http://www.alsa-project.org/db/?f=3ca8243c0626844f0264a3faad0aa72018bc14f4 Here for the first time support to audio (except mics) for mba1,2 (which is morally the same as 1,1) is patched into the kernel http://www.alsa-project.org/pipermail/alsa-devel/2010-February/025511.html The same jack supposedly works both for HP and ext MIC, I think it's called TRRS, and it's the same as the one used e.g. for iphones This guy might have done a similar job, though to a more recent version and for sound globally, not just mics: http://blogs.aerys.in/jeanmarc-leroux/2013/09/15/fixing-2013-macbook-air-ubuntu-sound-issue/ (this is mirror to http://unix.stackexchange.com/questions/73044/microphones-not-working-on-apple-macbook-air-1-1-early-2008-under-linux )

  Read the article

• keyboard mappings are totally screwed after updating to kde4

  - by zeonglow

  I recently upgraded from KDE 3.5 to KDE 4, and I have been having weird issues with my keyboard. In one of the virtual consoles e.g. when I press ctrl + alt 1 , I can type perfectly, but in KDE, several of the number keys don't work, the left and right arrows don't work either. When I press the right arrow key in xev I get this: KeyRelease event, serial 34, synthetic NO, window 0x3600001, root 0x6f, subw 0x0, time 903459, (111,55), root:(115,836), state 0x10, keycode 114 (keysym 0x1008ff11, XF86AudioLowerVolume), same_screen YES, XLookupString gives 0 bytes: XFilterEvent returns: False When I press the '3' key it toggles my Bookmarks toolbar in Firefox, in xev I get this: KeyPress event, serial 34, synthetic NO, window 0x3600001, root 0x6f, subw 0x0, time 999968, (94,115), root:(98,896), state 0x10, keycode 12 (keysym 0x1008ff30, XF86Favorites), same_screen YES, XLookupString gives 0 bytes: XmbLookupString gives 0 bytes: XFilterEvent returns: False KeyRelease event, serial 34, synthetic NO, window 0x3600001, root 0x6f, subw 0x0, time 1000032, (94,115), root:(98,896), state 0x10, keycode 12 (keysym 0x1008ff30, XF86Favorites), same_screen YES, XLookupString gives 0 bytes: XFilterEvent returns: False As this is deeper down, changing the type of keyboard in the KDE meun's has no effect. I'm slowly beginning to wade through the mountains of documentation about the X keyboard model, but there has to be a better way. Does anyone no what it is? Edit: 1234567890 ! after deleting the entire .kde folder. but only until I change the Keyboard settings from the "system settings" applet, then its hosed full time. Regardless of what I set the settings too. (restore to default settings doesn't) 2nd Edit: I'm using Gentoo AMD64, I was upgrading from KDE 3.5 KDE 4.2. I think I had manual settings before, although I didn't change anything. I was originally running KDE without HAL until that stop working a year or so ago. The only customisation I made was to set the multimedia keys to control Amarok. 3rd Edit $ grep xkb /var/log/Xorg.0.log (**) Option "xkb_rules" "evdev" (**) Option "xkb_model" "evdev" (**) Option "xkb_layout" "us" (**) Option "xkb_rules" "evdev" (**) Option "xkb_model" "evdev" (**) Option "xkb_layout" "us" Xorg.0.log has this to say: (WW) AllowEmptyInput is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled. (WW) Disabling Mouse1 (WW) Disabling Keyboard1 My Xorg.conf has this in it. Identifier "Keyboard1" Driver "kbd" Option "AutoRepeat" "500 30" # Specify which keyboard LEDs can be user-controlled (eg, with xset(1)) Option "XkbRules" "xorg" Option "XkbModel" "pc105" Option "XkbLayout" "gb"

  Read the article

• Two network interfaces and two IP addresses on the same subnet in Linux

  - by Scott Duckworth

  I recently ran into a situation where I needed two IP addresses on the same subnet assigned to one Linux host so that we could run two SSL/TLS sites. My first approach was to use IP aliasing, e.g. using eth0:0, eth0:1, etc, but our network admins have some fairly strict settings in place for security that squashed this idea: They use DHCP snooping and normally don't allow static IP addresses. Static addressing is accomplished by using static DHCP entries, so the same MAC address always gets the same IP assignment. This feature can be disabled per switchport if you ask and you have a reason for it (thankfully I have a good relationship with the network guys and this isn't hard to do). With the DHCP snooping disabled on the switchport, they had to put in a rule on the switch that said MAC address X is allowed to have IP address Y. Unfortunately this had the side effect of also saying that MAC address X is ONLY allowed to have IP address Y. IP aliasing required that MAC address X was assigned two IP addresses, so this didn't work. There may have been a way around these issues on the switch configuration, but in an attempt to preserve good relations with the network admins I tried to find another way. Having two network interfaces seemed like the next logical step. Thankfully this Linux system is a virtual machine, so I was able to easily add a second network interface (without rebooting, I might add - pretty cool). A few keystrokes later I had two network interfaces up and running and both pulled IP addresses from DHCP. But then the problem came in: the network admins could see (on the switch) the ARP entry for both interfaces, but only the first network interface that I brought up would respond to pings or any sort of TCP or UDP traffic. After lots of digging and poking, here's what I came up with. It seems to work, but it also seems to be a lot of work for something that seems like it should be simple. Any alternate ideas out there? Step 1: Enable ARP filtering on all interfaces: # sysctl -w net.ipv4.conf.all.arp_filter=1 # echo "net.ipv4.conf.all.arp_filter = 1" >> /etc/sysctl.conf From the file networking/ip-sysctl.txt in the Linux kernel docs: arp_filter - BOOLEAN 1 - Allows you to have multiple network interfaces on the same subnet, and have the ARPs for each interface be answered based on whether or not the kernel would route a packet from the ARP'd IP out that interface (therefore you must use source based routing for this to work). In other words it allows control of which cards (usually 1) will respond to an arp request. 0 - (default) The kernel can respond to arp requests with addresses from other interfaces. This may seem wrong but it usually makes sense, because it increases the chance of successful communication. IP addresses are owned by the complete host on Linux, not by particular interfaces. Only for more complex setups like load- balancing, does this behaviour cause problems. arp_filter for the interface will be enabled if at least one of conf/{all,interface}/arp_filter is set to TRUE, it will be disabled otherwise Step 2: Implement source-based routing I basically just followed directions from http://lartc.org/howto/lartc.rpdb.multiple-links.html, although that page was written with a different goal in mind (dealing with two ISPs). Assume that the subnet is 10.0.0.0/24, the gateway is 10.0.0.1, the IP address for eth0 is 10.0.0.100, and the IP address for eth1 is 10.0.0.101. Define two new routing tables named eth0 and eth1 in /etc/iproute2/rt_tables: ... top of file omitted ... 1 eth0 2 eth1 Define the routes for these two tables: # ip route add default via 10.0.0.1 table eth0 # ip route add default via 10.0.0.1 table eth1 # ip route add 10.0.0.0/24 dev eth0 src 10.0.0.100 table eth0 # ip route add 10.0.0.0/24 dev eth1 src 10.0.0.101 table eth1 Define the rules for when to use the new routing tables: # ip rule add from 10.0.0.100 table eth0 # ip rule add from 10.0.0.101 table eth1 The main routing table was already taken care of by DHCP (and it's not even clear that its strictly necessary in this case), but it basically equates to this: # ip route add default via 10.0.0.1 dev eth0 # ip route add 130.127.48.0/23 dev eth0 src 10.0.0.100 # ip route add 130.127.48.0/23 dev eth1 src 10.0.0.101 And voila! Everything seems to work just fine. Sending pings to both IP addresses works fine. Sending pings from this system to other systems and forcing the ping to use a specific interface works fine (ping -I eth0 10.0.0.1, ping -I eth1 10.0.0.1). And most importantly, all TCP and UDP traffic to/from either IP address works as expected. So again, my question is: is there a better way to do this? This seems like a lot of work for a seemingly simple problem.

  Read the article

• DVD Drive Failing on Windows 7

  - by Seth Spearman

  Hello, I have x64 Windows 7 running on an ASUS M50VM. The DVD drive works completely unreliably if not at all. But the story is not that simple so bear with me...here are the gory details. When I first got the machine it came with Windows XP and I upgraded it to Windows Vista X64 and the DVD worked fine. When Windows 7 RC2 came out I tried it on a Virtual Machine and I liked it so much that I upgraded the machine to Win7 RC1. The DVD worked fine. Of course, RC1 was going to start spontaneously rebooting, so when Windows 7 was released I DID A CLEAN INSTALL of Windows 7. Just to clarify...by clean install I mean I did a FORMAT of the HARD DRIVE and INSTALLED it from scratch. EVER since then the DVD mostly doesn't work. I can sometime read from disk but that will often hang. (Please see my description below of HANG for details.) CD or DVD writes ALWAYS fail with a HANG (I have done a successful write only one time.) Here is what I mean by HANG... *Explorer Window is unresponsive. *Any software accessing the DVD drive is unresponsive. *The DVD tray will not eject. *Using a paper clip will eject but the disk is usually spinning real hard. *Attempting to shut down windows will fail. I have waited as long as ten minutes but the whole OS seems to hang. I do a hard shutdown. *Sometimes accessing the DVD (when it does not cause a HANG) will still fail and the device will actually seem to disappear from the system until I reboot. A couple of other things. It is NOT a hardware failure. It is the Windows OS. I know this because I swapped out my DVD drive with a friend with the same model...his machine is fine (he is still running Vista X64) and my machine still fails. For what it is worth. I swapped out my primary disk with the INTEL 160GB SSD. EDIT Here is what System Information shows about my DVD drive Drive D: Description CD-ROM Drive Media Loaded No Media Type DVD Writer Name HL-DT-ST DVDRAM GSA-T50N ATA Device Manufacturer (Standard CD-ROM drives) Status OK Transfer Rate -1.00 kbytes/sec SCSI Target ID 0 PNP Device ID IDE\CDROMHL-DT-ST_DVDRAM_GSA-T50N________________RR04____\5&2B5B7F1D&0&1.0.0 Driver c:\windows\system32\drivers\cdrom.sys (6.1.7600.16385, 144.00 KB (147,456 bytes), 7/13/2009 7:19 PM) Any ideas? HELP! Seth B Spearman

  Read the article

• Internet connection sharing between Windows XP and Windows 7

  - by Dave

  I bought my lil sister's netbooks for Christmas and I've been having a heck of a time trying to get Internet Connection Sharing to work. The host computer is a Windows XP box and it uses a US Cellular 3G modem dongle thingy to set it's Internet access. Additionally I have a hard wire plugged into the LAN1 port of the router described below. (I tried the WAN port out of desperation but things didn't seem happy that way.) Additionally they have a linksys router (can't remember specific model number, I will find this out) that I was using to take advantage of it's wireless capabilities. Originally thought about updating the router to use dd-wrt, but after reading the instructions it looked like to much of a pita (had to downgrade firmware, then install dd-wrt) to set up, eventually I caved, out of desperation, and ended up successfully installing dd-wrt on the router. I have DHCP turned off on the router, actually all I could select was DHCP forwarder. The netbooks both have windows 7 starter installed on them. Initially, I had the networks joined to a homegroup but I dropped that and everyone is able to see everyone in their respective network explorers. When I turn on Internet Connection Sharing on the host, its IP on the LAN changed to 192.168.0.1, so I arbitrarily decided to assign the router to port 192.168.0.100. When I connect the netbooks they get IPs dynamically. As I stated before, everyone can see everyone in the network explorer, and shares can be accessed. The weird thing is that everyone can ping the router but they cannot ping each others IPs. The status on the netbooks says that there is no Internet Connectivity. Another thing I tried was manually setting the DNS servers on the netbooks to the DNS servers that the host computer has. The funny thing is when I ping an outside domain such as google.com the IP address resolves, however I get no responses from the pings. When I tried plugging the host into the WAN port I could ping the router, nor could I access the router's web access admin. Another thing I tried was turning off the firewall on the netbooks and the firewall off on the host computer for the LAN connection, and they still could not ping each other. Also I thought I should be able to start a remote desktop connection but I couldn't do that either, I also checked to make sure that computers would in fact accept a request for remote desktop connections.

  Read the article

• DVD Drive Failing on Windows 7

  - by Seth Spearman

  I have x64 Windows 7 running on an ASUS M50VM. The DVD drive works completely unreliably if not at all. But the story is not that simple so bear with me...here are the gory details. When I first got the machine it came with Windows XP and I upgraded it to Windows Vista X64 and the DVD worked fine. When Windows 7 RC2 came out I tried it on a Virtual Machine and I liked it so much that I upgraded the machine to Win7 RC1. The DVD worked fine. Of course, RC1 was going to start spontaneously rebooting, so when Windows 7 was released I DID A CLEAN INSTALL of Windows 7. Just to clarify...by clean install I mean I did a FORMAT of the HARD DRIVE and INSTALLED it from scratch. EVER since then the DVD mostly doesn't work. I can sometime read from disk but that will often hang. (Please see my description below of HANG for details.) CD or DVD writes ALWAYS fail with a HANG (I have done a successful write only one time.) Here is what I mean by HANG... *Explorer Window is unresponsive. *Any software accessing the DVD drive is unresponsive. *The DVD tray will not eject. *Using a paper clip will eject but the disk is usually spinning real hard. *Attempting to shut down windows will fail. I have waited as long as ten minutes but the whole OS seems to hang. I do a hard shutdown. *Sometimes accessing the DVD (when it does not cause a HANG) will still fail and the device will actually seem to disappear from the system until I reboot. A couple of other things. It is NOT a hardware failure. It is the Windows OS. I know this because I swapped out my DVD drive with a friend with the same model...his machine is fine (he is still running Vista X64) and my machine still fails. For what it is worth. I swapped out my primary disk with the INTEL 160GB SSD. EDIT Here is what System Information shows about my DVD drive Drive D: Description CD-ROM Drive Media Loaded No Media Type DVD Writer Name HL-DT-ST DVDRAM GSA-T50N ATA Device Manufacturer (Standard CD-ROM drives) Status OK Transfer Rate -1.00 kbytes/sec SCSI Target ID 0 PNP Device ID IDE\CDROMHL-DT-ST_DVDRAM_GSA-T50N________________RR04____\5&2B5B7F1D&0&1.0.0 Driver c:\windows\system32\drivers\cdrom.sys (6.1.7600.16385, 144.00 KB (147,456 bytes), 7/13/2009 7:19 PM) Any ideas? HELP! Seth B Spearman

  Read the article

• My linux server takes more than an hour to boot. Suggestions?

  - by jamieb

  I am building a CentOS 5.4 system that boots off a compact flash card using a card reader that emulates an IDE drive. It literally takes about an hour to boot. The ultra-slow part occurs when Grub is loading the kernel. Once that's done, the rest of the boot process only takes about a minute to get to a login prompt. Does anyone have any suggestions? I suspect that it may have to do with UDMA. Everything IDE-related in my BIOS seems to checkout. The read performance hdparm is telling me 1.77 MB/s. Ouch! (But even at that rate, it still shouldn't take an hour to decompress and load the kernel) [root@server ~]# hdparm -tT /dev/hdc /dev/hdc: Timing cached reads: 2444 MB in 2.00 seconds = 1222.04 MB/sec Timing buffered disk reads: 6 MB in 3.39 seconds = 1.77 MB/sec Trying to enable DMA is a no-go though: [root@server ~]# hdparm -d1 /dev/hdc /dev/hdc: setting using_dma to 1 (on) HDIO_SET_DMA failed: Operation not permitted using_dma = 0 (off) Here's some command outputs that might help: System [root@server ~]# uname -a Linux server.localdomain 2.6.18-164.el5xen #1 SMP Thu Sep 3 04:47:32 EDT 2009 i686 i686 i386 GNU/Linux PCI info: [root@server ~]# lspci -v 00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02) Subsystem: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub Flags: bus master, fast devsel, latency 0 Capabilities: [e0] Vendor Specific Information 00:02.0 VGA compatible controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02) (prog-if 00 [VGA controller]) Subsystem: Intel Corporation 82945G/GZ Integrated Graphics Controller Flags: bus master, fast devsel, latency 0, IRQ 10 Memory at fdf00000 (32-bit, non-prefetchable) [size=512K] I/O ports at ff00 [size=8] Memory at d0000000 (32-bit, prefetchable) [size=256M] Memory at fdf80000 (32-bit, non-prefetchable) [size=256K] Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0 Enable- Capabilities: [d0] Power Management version 2 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 Flags: bus master, medium devsel, latency 0, IRQ 16 I/O ports at fe00 [size=32] 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 Flags: bus master, medium devsel, latency 0, IRQ 17 I/O ports at fd00 [size=32] 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 Flags: bus master, medium devsel, latency 0, IRQ 18 I/O ports at fc00 [size=32] 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 Flags: bus master, medium devsel, latency 0, IRQ 19 I/O ports at fb00 [size=32] 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller Flags: bus master, medium devsel, latency 0, IRQ 16 Memory at fdfff000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01 [Subtractive decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: fde00000-fdefffff Prefetchable memory behind bridge: 00000000fdd00000-00000000fdd00000 Capabilities: [50] #0d [0000] 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01) Subsystem: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge Flags: bus master, medium devsel, latency 0 Capabilities: [e0] Vendor Specific Information 00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01) (prog-if 80 [Master]) Subsystem: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 17 I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at f800 [size=16] Capabilities: [70] Power Management version 2 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01) Subsystem: Intel Corporation 82801G (ICH7 Family) SMBus Controller Flags: medium devsel, IRQ 17 I/O ports at 0500 [size=32] 01:04.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 18 I/O ports at de00 [size=256] Memory at fdeff000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 01:06.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 17 I/O ports at dc00 [size=256] Memory at fdefe000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 01:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 19 I/O ports at da00 [size=256] Memory at fdefd000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 hdparm ouput: [root@server ~]# hdparm /dev/hdc /dev/hdc: multcount = 0 (off) IO_support = 0 (default 16-bit) unmaskirq = 0 (off) using_dma = 0 (off) keepsettings = 0 (off) readonly = 0 (off) readahead = 256 (on) geometry = 8146/16/63, sectors = 8211168, start = 0 [root@server ~]# hdparm -I /dev/hdc /dev/hdc: ATA device, with non-removable media Model Number: InnoDisk Corp. - iCF4000 4GB Serial Number: 20091023AACA70000753 Firmware Revision: 081107 Standards: Supported: 5 Likely used: 6 Configuration: Logical max current cylinders 8146 8146 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 8211168 LBA user addressable sectors: 8211168 device size with M = 1024*1024: 4009 MBytes device size with M = 1000*1000: 4204 MBytes (4 GB) Capabilities: LBA, IORDY(can be disabled) Standby timer values: spec'd by Vendor R/W multiple sector transfer: Max = 2 Current = 2 DMA: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * Power Management feature set * WRITE_BUFFER command * READ_BUFFER command * NOP cmd * CFA feature set * Mandatory FLUSH_CACHE HW reset results: CBLID- above Vih Device num = 0 CFA power mode 1: enabled and required by some commands Maximum current = 100ma Checksum: correct

  Read the article

• Xen DomU on DRBD device: barrier errors

  - by Halfgaar

  I'm testing setting up a Xen DomU with a DRBD storage for easy failover. Most of the time, immediatly after booting the DomU, I get an IO error: [ 3.153370] EXT3-fs (xvda2): using internal journal [ 3.277115] ip_tables: (C) 2000-2006 Netfilter Core Team [ 3.336014] nf_conntrack version 0.5.0 (3899 buckets, 15596 max) [ 3.515604] init: failsafe main process (397) killed by TERM signal [ 3.801589] blkfront: barrier: write xvda2 op failed [ 3.801597] blkfront: xvda2: barrier or flush: disabled [ 3.801611] end_request: I/O error, dev xvda2, sector 52171168 [ 3.801630] end_request: I/O error, dev xvda2, sector 52171168 [ 3.801642] Buffer I/O error on device xvda2, logical block 6521396 [ 3.801652] lost page write due to I/O error on xvda2 [ 3.801755] Aborting journal on device xvda2. [ 3.804415] EXT3-fs (xvda2): error: ext3_journal_start_sb: Detected aborted journal [ 3.804434] EXT3-fs (xvda2): error: remounting filesystem read-only [ 3.814754] journal commit I/O error [ 6.973831] init: udev-fallback-graphics main process (538) terminated with status 1 [ 6.992267] init: plymouth-splash main process (546) terminated with status 1 The manpage of drbdsetup says that LVM (which I use) doesn't support barriers (better known as tagged command queuing or native command queing), so I configured the drbd device not to use barriers. This can be seen in /proc/drbd (by "wo:f, meaning flush, the next method drbd chooses after barrier): 3: cs:Connected ro:Primary/Secondary ds:UpToDate/UpToDate C r---- ns:2160152 nr:520204 dw:2680344 dr:2678107 al:3549 bm:9183 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:0 And on the other host: 3: cs:Connected ro:Secondary/Primary ds:UpToDate/UpToDate C r---- ns:0 nr:2160152 dw:2160152 dr:0 al:0 bm:8052 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:0 I also enabled the option disable_sendpage, as per the drbd docs: cat /sys/module/drbd/parameters/disable_sendpage Y I also tried adding barriers=0 to fstab as mount option. Still it sometimes says: [ 58.603896] blkfront: barrier: write xvda2 op failed [ 58.603903] blkfront: xvda2: barrier or flush: disabled I don't even know if ext3 has a nobarrier option. And, because only one of my storage systems is battery backed, it would not be smart anyway. Why does it still compain about barriers when I disabled that? Both host are: Debian: 6.0.4 uname -a: Linux 2.6.32-5-xen-amd64 drbd: 8.3.7 Xen: 4.0.1 Guest: Ubuntu 12.04 LTS uname -a: Linux 3.2.0-24-generic pvops drbd resource: resource drbdvm { meta-disk internal; device /dev/drbd3; startup { # The timeout value when the last known state of the other side was available. 0 means infinite. wfc-timeout 0; # Timeout value when the last known state was disconnected. 0 means infinite. degr-wfc-timeout 180; } syncer { # This is recommended only for low-bandwidth lines, to only send those # blocks which really have changed. #csums-alg md5; # Set to about half your net speed rate 60M; # It seems that this option moved to the 'net' section in drbd 8.4. (later release than Debian has currently) verify-alg md5; } net { # The manpage says this is recommended only in pre-production (because of its performance), to determine # if your LAN card has a TCP checksum offloading bug. #data-integrity-alg md5; } disk { # Detach causes the device to work over-the-network-only after the # underlying disk fails. Detach is not default for historical reasons, but is # recommended by the docs. # However, the Debian defaults in drbd.conf suggest the machine will reboot in that event... on-io-error detach; # LVM doesn't support barriers, so disabling it. It will revert to flush. Check wo: in /proc/drbd. If you don't disable it, you get IO errors. no-disk-barrier; } on host1 { # universe is a VG disk /dev/universe/drbdvm-disk; address 10.0.0.1:7792; } on host2 { # universe is a VG disk /dev/universe/drbdvm-disk; address 10.0.0.2:7792; } } DomU cfg: bootloader = '/usr/lib/xen-default/bin/pygrub' vcpus = '2' memory = '512' # # Disk device(s). # root = '/dev/xvda2 ro' disk = [ 'phy:/dev/drbd3,xvda2,w', 'phy:/dev/universe/drbdvm-swap,xvda1,w', ] # # Hostname # name = 'drbdvm' # # Networking # # fake IP for posting vif = [ 'ip=1.2.3.4,mac=00:16:3E:22:A8:A7' ] # # Behaviour # on_poweroff = 'destroy' on_reboot = 'restart' on_crash = 'restart' In my test setup: the primary host's storage is 9650SE SATA-II RAID PCIe with battery. The secondary is software RAID1. Isn't DRBD+Xen widely used? With these problems, it's not going to work.

  Read the article

• GeForce 8800GT not even giving basic output

  - by Sam

  My Dad bought a GeForce 8800GT graphics card quite a long time ago now. It has never worked in his PC. Print out from a dxdiag: System Information Time of this report: 4/13/2010, 19:52:40 Machine name: USER-PC Operating System: Windows Vista™ Home Premium (6.0, Build 6001) Service Pack 1 (6001.vistasp1_gdr.091208-0542) Language: English (Regional Setting: English) System Manufacturer: To Be Filled By O.E.M. System Model: To Be Filled By O.E.M. BIOS: Default System BIOS Processor: Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz (4 CPUs), ~2.3GHz Memory: 2046MB RAM Page File: 1045MB used, 3296MB available Windows Dir: C:\Windows DirectX Version: DirectX 10 DX Setup Parameters: Not found DxDiag Version: 6.00.6001.18000 32bit Unicode DxDiag Notes Display Tab 1: No problems found. Sound Tab 1: No problems found. Sound Tab 2: No problems found. Sound Tab 3: No problems found. Input Tab: No problems found. DirectX Debug Levels Direct3D: 0/4 (retail) DirectDraw: 0/4 (retail) DirectInput: 0/5 (retail) DirectMusic: 0/5 (retail) DirectPlay: 0/9 (retail) DirectSound: 0/5 (retail) DirectShow: 0/6 (retail) Display Devices Card name: ATI Radeon HD 2400 PRO Manufacturer: ATI Technologies Inc. Chip type: ATI Radeon Graphics Processor (0x94C3) DAC type: Internal DAC(400MHz) Device Key: Enum\PCI\VEN_1002&DEV_94C3&SUBSYS_00000000&REV_00 Display Memory: 1012 MB Dedicated Memory: 245 MB Shared Memory: 767 MB Current Mode: 1280 x 960 (32 bit) (75Hz) Monitor: Generic PnP Monitor Driver Name: atiumdag.dll,atiumdva.dat,atitmmxx.dll Driver Version: 7.14.0010.0523 (English) DDI Version: 10 Driver Attributes: Final Retail Driver Date/Size: 8/22/2007 02:43:14, 3021312 bytes That info is from the current card that is installed in it and has been installed since its purchase roughly 3-4 years ago. When I physically install the card I put it into a purple slot on the motherboard that the old card was in (if I go into the device manager and select properties on the current card it confirms that the slot is a "PCI Slot 16 (PCI bus 2, device 0, function 0)") and boot up the computer but get absolutely no output. The screen that we have registers that it is connected to something (by not displaying the screen it does when the cable is unplugged) but just remains blank, no output at all. I recently took the card to my University and one of my friends who is better with hardware issues than I am tried it in his system and it worked perfectly. No issues whatsoever. I do not have a spec list for his system but I could get one if you need it. If you need any more information on this issue I will be happy to supply you with it as I am starting to get very annoyed with this problem ^_^

  Read the article

• Unable to access intel fake RAID 1 array in Fedora 14 after reboot

  - by Sim

  Hello everyone, 1st I am relatively new to linux (but not to *nix). I have 4 disks assembled in the following intel ahci bios fake raid arrays: 2x320GB RAID1 - used for operating systems md126 2x1TB RAID1 - used for data md125 I have used the raid of size 320GB to install my operating system and the second raid I didn't even select during the installation of Fedora 14. After successful partitioning and installation of Fedora, I tried to make the second array available, it was possible to make it visible in linux with mdadm --assembe --scan , after that I created one maximum size partition and 1 maximum size ext4 filesystem in it. Mounted, and used it. After restart - a few I/O errors during boot regarding md125 + inability to mount the filesystem on it and dropped into repair shell. I commented the filesystem in fstab and it booted. To my surprise, the array was marked as "auto read only": [root@localhost ~]# cat /proc/mdstat Personalities : [raid1] md125 : active (auto-read-only) raid1 sdc[1] sdd[0] 976759808 blocks super external:/md127/0 [2/2] [UU] md127 : inactive sdc[1](S) sdd[0](S) 4514 blocks super external:imsm md126 : active raid1 sda[1] sdb[0] 312566784 blocks super external:/md1/0 [2/2] [UU] md1 : inactive sdb[1](S) sda[0](S) 4514 blocks super external:imsm unused devices: <none> [root@localhost ~]# and the partition in it was not available as device special file in /dev: [root@localhost ~]# ls -l /dev/md125* brw-rw---- 1 root disk 9, 125 Jan 6 15:50 /dev/md125 [root@localhost ~]# But the partition is there according to fdisk: [root@localhost ~]# fdisk -l /dev/md125 Disk /dev/md125: 1000.2 GB, 1000202043392 bytes 19 heads, 10 sectors/track, 10281682 cylinders, total 1953519616 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x1b238ea9 Device Boot Start End Blocks Id System /dev/md125p1 2048 1953519615 976758784 83 Linux [root@localhost ~]# I tried to "activate" the array in different ways (I'm not experienced with mdadm and the man page is gigantic so I was only browsing it looking for my answer) but it was impossible - the array would still stay in "auto read only" and the device special file for the partition it will not be in /dev. It was only after I recreated the partition via fdisk that it reappeared in /dev... until next reboot. So, my question is - How do I make the array automatically available after reboot? Here is some additional information: 1st I am able to see the UUID of the array in blkid: [root@localhost ~]# blkid /dev/sdc: UUID="b9a1149f-ae11-4fc8-a600-0d77354dc42a" SEC_TYPE="ext2" TYPE="ext3" /dev/sdd: UUID="b9a1149f-ae11-4fc8-a600-0d77354dc42a" SEC_TYPE="ext2" TYPE="ext3" /dev/md126p1: UUID="60C8D9A7C8D97C2A" TYPE="ntfs" /dev/md126p2: UUID="3d1b38a3-b469-4b7c-b016-8abfb26a5d7d" TYPE="ext4" /dev/md126p3: UUID="1Msqqr-AAF8-k0wi-VYnq-uWJU-y0OD-uIFBHL" TYPE="LVM2_member" /dev/mapper/vg00-rootlv: LABEL="_Fedora-14-x86_6" UUID="34cc1cf5-6845-4489-8303-7a90c7663f0a" TYPE="ext4" /dev/mapper/vg00-swaplv: UUID="4644d857-e13b-456c-ac03-6f26299c1046" TYPE="swap" /dev/mapper/vg00-homelv: UUID="82bd58b2-edab-4b4b-aec4-b79595ecd0e3" TYPE="ext4" /dev/mapper/vg00-varlv: UUID="1b001444-5fdd-41b6-a59a-9712ec6def33" TYPE="ext4" /dev/mapper/vg00-tmplv: UUID="bf7d2459-2b35-4a1c-9b81-d4c4f24a9842" TYPE="ext4" /dev/md125: UUID="b9a1149f-ae11-4fc8-a600-0d77354dc42a" SEC_TYPE="ext2" TYPE="ext3" /dev/sda: TYPE="isw_raid_member" /dev/md125p1: UUID="420adfdd-6c4e-4552-93f0-2608938a4059" TYPE="ext4" [root@localhost ~]# Here is how /etc/mdadm.conf looks like: [root@localhost ~]# cat /etc/mdadm.conf # mdadm.conf written out by anaconda MAILADDR root AUTO +imsm +1.x -all ARRAY /dev/md1 UUID=89f60dee:e46a251f:7475814b:d4cc19a9 ARRAY /dev/md126 UUID=a8775c90:cee66376:5310fc13:63bcba5b ARRAY /dev/md125 UUID=b9a1149f:ae114fc8:a6000d77:354dc42a [root@localhost ~]# here is how /proc/mdstat looks like after I recreate the partition in the array so that it becomes available: [root@localhost ~]# cat /proc/mdstat Personalities : [raid1] md125 : active raid1 sdc[1] sdd[0] 976759808 blocks super external:/md127/0 [2/2] [UU] md127 : inactive sdc[1](S) sdd[0](S) 4514 blocks super external:imsm md126 : active raid1 sda[1] sdb[0] 312566784 blocks super external:/md1/0 [2/2] [UU] md1 : inactive sdb[1](S) sda[0](S) 4514 blocks super external:imsm unused devices: <none> [root@localhost ~]# Detailed output regarding the array in subject: [root@localhost ~]# mdadm --detail /dev/md125 /dev/md125: Container : /dev/md127, member 0 Raid Level : raid1 Array Size : 976759808 (931.51 GiB 1000.20 GB) Used Dev Size : 976759940 (931.51 GiB 1000.20 GB) Raid Devices : 2 Total Devices : 2 Update Time : Fri Jan 7 00:38:00 2011 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 UUID : 30ebc3c2:b6a64751:4758d05c:fa8ff782 Number Major Minor RaidDevice State 1 8 32 0 active sync /dev/sdc 0 8 48 1 active sync /dev/sdd [root@localhost ~]# and /etc/fstab, with /data commented (the filesystem that is on this array): # # /etc/fstab # Created by anaconda on Thu Jan 6 03:32:40 2011 # # Accessible filesystems, by reference, are maintained under '/dev/disk' # See man pages fstab(5), findfs(8), mount(8) and/or blkid(8) for more info # /dev/mapper/vg00-rootlv / ext4 defaults 1 1 UUID=3d1b38a3-b469-4b7c-b016-8abfb26a5d7d /boot ext4 defaults 1 2 #UUID=420adfdd-6c4e-4552-93f0-2608938a4059 /data ext4 defaults 0 1 /dev/mapper/vg00-homelv /home ext4 defaults 1 2 /dev/mapper/vg00-tmplv /tmp ext4 defaults 1 2 /dev/mapper/vg00-varlv /var ext4 defaults 1 2 /dev/mapper/vg00-swaplv swap swap defaults 0 0 tmpfs /dev/shm tmpfs defaults 0 0 devpts /dev/pts devpts gid=5,mode=620 0 0 sysfs /sys sysfs defaults 0 0 proc /proc proc defaults 0 0 [root@localhost ~]# Thanks in advance to everyone that even read this whole issue :-)

  Read the article

• Crashes and freezes after fixing "BOOTMGR is missing" error

  - by Greg-J

  I came back from a 3-day weekend to a computer that was off. I leave my PC on 24/7, so this was odd. Turn it on to get the dreaded "BOOTMGR is missing" screen. Two attempts at Windows Recovery and it booted into Windows fine. After an hour or so, I get a frozen Chrome and my start bar disappears. Ctrl+Alt+Del brings up an error box telling me that Ctrl+Alt+Del failed to work properly. Clicking on any open application triggers an error (I can't recall the error now, but it essentially just said that the application couldn't be found running or something along those lines). I restart, and again, the same thing happens after a while of use. I turn it on, install the 47 updates I have or so, and then restart it. After a while of use (under an hour), it just freezes completely. My thoughts are: SSDs, RAM or PS. My system specs below: (RAID0) 2 x Crucial M4 CT128M4SSD2 2.5" 128GB SATA III MLC Internal Solid State Drive (SSD) CORSAIR Vengeance 16GB (4 x 4GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800) Desktop Memory Model CML16GX3M4A1600C9 CORSAIR HX Series HX750 750W ATX12V 2.3 / EPS12V 2.91 SLI Ready CrossFire Ready 80 PLUS GOLD Certified Modular Active 1 x ASUS Maximus IV Gene-Z/GEN3 LGA 1155 Intel Z68 HDMI SATA 6Gb/s USB 3.0 Micro ATX Intel Motherboard 1 x Hitachi GST Deskstar 7K1000.C 0F10383 1TB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive -Bare Drive 1 x Intel Core i7-2600K Sandy Bridge 3.4GHz (3.8GHz Turbo Boost) LGA 1155 95W Quad-Core Desktop Processor Intel HD Graphics 1 x SAPPHIRE 21197-00-40G Radeon HD 7970 3GB 384-bit GDDR5 PCI Express 3.0 x16 HDCP Ready CrossFireX Support Video Card 1 x Noctua NH-D14 120mm & 140mm SSO CPU Cooler This is all crammed in a pretty small case (NZXT Vulcan) and has been running perfectly problem-free since January. The only thing out of the ordinary is that there is a fan in the case that is now making noise whereas the case has previously been completely silent. I have no reason to believe this is anything more then correlation, but felt it is worth mentioning. I believe it MAY be the SSDs simply because of the BOOTMGR error, but not sure how to test that theory. My belief that it may be the RAM is simply from experience with frozen machines. I haven't had the time to memtest it, but will. The PS being the culprit is something I've picked up by reading similar threads on various forums, and it seems plausible. I am unsure how to test this though. ANY insight whatsover would be greatly appreciated!

  Read the article

• Installing Windows on HP Proliant Servers without SmartStart

  - by Fitzroy

  I have a PXE server for deploying Windows XP and Windows 7 to workstations. The process is as follows: Boot the workstation from the NIC. Workstation sends a DHCP request. DHCP server responds with an IP address and the location of the PXE server. Workstation downloads WinPE image file from PXE server via TFTP Workstation stores WinPE image file in memory and executes it. Once booted into WinPE, I connect to a network share to gain access to either the Windows XP or Windows 7 installation files. A custom script is launched to guide you through the process of formatting and partitioning the hard drive(s) (using DISKPART and FORMAT). Another custom script asks for details such as the hostname to assign to the workstation. The answers provided are used to build an unattended answer file (SIF [Setup Information File] for WinXP and XML for Win7). The Windows setup EXE is launched, passing the unattended answer file to it as a parameter. The Windows XP and Windows 7 installation sources have been customised to include the drivers for our Dell workstations. They also run a number of scripts upon first booting up to install software packages. This process works very well for our workstations and I would now like to use it for building our servers too. The vast majority of our servers are HP Proliant DL360 G6, DL380 G5 and DL380 G6. They’re running Windows Server 2003 (various editions) or 2008 (various editions). To date, we have always built the HP Proliant servers using the SmartStart CD provided. SmartStart does three useful things for us: Setup RAID with HP Array Configuration Utility (ACU). Installs and configures SNMP Installs various HP Tools for Windows (HP Array Configuration Utility, HP Array Diagnostic Utility, HP Proliant Integrated Management Log Viewer, etc) Using SmartStart I have never had to manually download and install Windows drivers for network, sound, video, etc. I'm not sure if this is because SmartStart copies drivers from the CD during setup, or whether Windows just has the drivers natively in its driver CAB. If I abandon the SmartStart CD in favour of my PXE server I would have to do the following: As I wont have access to ACU, I'll configure the RAID (before booting to the PXE server) by pressing F8 (during the boot process) to access Option ROM Configuration for Arrays (ORCA). Installation of SNMP and the HP Tools will have to be installed once the Windows installation is complete using the Proliant Support Pack. Is this method OK? Is there anything that the SmartStart CD does that I'll be unable to do by other means? Are there any disadvantages to not using the SmartStart CD? Many thanks. UPDATE 05/01/12 I’ve been reading through the SmartStart Scripting Toolkit documentation. The scripting toolkit contains command line tools which work within WinPE and can such things as configure BIOS settings, configure an array and setup ILO. I’m personally not too bothered about configuring BIOS settings as I rarely deviate from the defaults (unless the server is to be a Hyper-V host). I’m not too fussed about being able to configure the array from within WinPE, as I’m happy to just press F8 and use Option ROM Configuration for Arrays (ORCA). Although, if it’s easy enough to do, I will explore this further, as it saves time if everything can be configured from within WinPE. One of the nice features all the tools possess is that you can pass input files to them. EG. Configure one server to your requirements, capture its configuration to a file (using the appropriate tool), you can then use the tool on other servers passing the input file with the captured configuration. Array controller drivers appear to be included with the toolkit along with example of how to incorporate them within a WinPE build. I suppose WinPE won’t be able to see logical volumes (I.E 2x physical disks in a RAID 1 configuration) without the array controller drivers? I mentioned in my post that SmartStart normally installs a bunch of Windows HP tools for you. I’ve had a look today, and if you run the SmartStart CD from within Windows all the tools can be installed. Therefore I can do this after the Windows installation is complete. The SmartStart CD appears to contain a lot Windows drivers. I can customise my Windows 2008 source to incorporate these drivers. However, I understand that incorporating an array controller driver is a little different to most drivers. I believe that you have to provide the driver during the very early stages of the Windows setup. I’m working through the Scripting Toolkit documentation to try and work this out...

  Read the article

• Motherboard/PSU crippling USB and Sata

  - by celebdor

  I very recently bought a new desktop computer. The motherboard is: Z77MX-D3H and the power supply is ocz zs series 550w. The issue I have is that once I boot to the operating system (I have tried with fedora and Ubuntu with kernels 2.6.38 - 3.4.0), my hard drive (2.5" Magnetic) occasionally makes a power switch noise and it resets. Needless to say, when this drive is the OS drive, the OS crashes. I also have a SSD that works fine with the same OS configurations, but if I have the magnetic hard drive attached as second drive, it works erratically and the reconnects result in corrupted data. I also noticed that whenever I plug an external hard drive USB2.0 or USB3.0 to the computer the issue with the reconnects is even worse: [ 52.198441] sd 7:0:0:0: [sdc] Spinning up disk... [ 57.955811] usb 4-3: USB disconnect, device number 3 [ 58.023687] .ready [ 58.023914] sd 7:0:0:0: [sdc] READ CAPACITY(16) failed [ 58.023919] sd 7:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 58.023932] sd 7:0:0:0: [sdc] Sense not available. [ 58.024061] sd 7:0:0:0: [sdc] READ CAPACITY failed [ 58.024063] sd 7:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 58.024064] sd 7:0:0:0: [sdc] Sense not available. [ 58.024099] sd 7:0:0:0: [sdc] Write Protect is off [ 58.024101] sd 7:0:0:0: [sdc] Mode Sense: 00 00 00 00 [ 58.024135] sd 7:0:0:0: [sdc] Asking for cache data failed [ 58.024137] sd 7:0:0:0: [sdc] Assuming drive cache: write through [ 58.024400] sd 7:0:0:0: [sdc] READ CAPACITY(16) failed [ 58.024402] sd 7:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 58.024405] sd 7:0:0:0: [sdc] Sense not available. [ 58.024448] sd 7:0:0:0: [sdc] READ CAPACITY failed [ 58.024450] sd 7:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 58.024451] sd 7:0:0:0: [sdc] Sense not available. [ 58.024469] sd 7:0:0:0: [sdc] Asking for cache data failed [ 58.024471] sd 7:0:0:0: [sdc] Assuming drive cache: write through [ 58.024472] sd 7:0:0:0: [sdc] Attached SCSI disk [ 58.407725] usb 4-3: new SuperSpeed USB device number 4 using xhci_hcd [ 58.424921] scsi8 : usb-storage 4-3:1.0 [ 59.424185] scsi 8:0:0:0: Direct-Access WD My Passport 0740 1003 PQ: 0 ANSI: 6 [ 59.424406] scsi 8:0:0:1: Enclosure WD SES Device 1003 PQ: 0 ANSI: 6 [ 59.425098] sd 8:0:0:0: Attached scsi generic sg2 type 0 [ 59.425176] ses 8:0:0:1: Attached Enclosure device [ 59.425248] ses 8:0:0:1: Attached scsi generic sg3 type 13 [ 61.845836] sd 8:0:0:0: [sdc] 976707584 512-byte logical blocks: (500 GB/465 GiB) [ 61.845838] sd 8:0:0:0: [sdc] 4096-byte physical blocks [ 61.846336] sd 8:0:0:0: [sdc] Write Protect is off [ 61.846338] sd 8:0:0:0: [sdc] Mode Sense: 47 00 10 08 [ 61.846718] sd 8:0:0:0: [sdc] No Caching mode page present [ 61.846720] sd 8:0:0:0: [sdc] Assuming drive cache: write through [ 61.848105] sd 8:0:0:0: [sdc] No Caching mode page present [ 61.848106] sd 8:0:0:0: [sdc] Assuming drive cache: write through [ 61.857147] sdc: sdc1 [ 61.858915] sd 8:0:0:0: [sdc] No Caching mode page present [ 61.858916] sd 8:0:0:0: [sdc] Assuming drive cache: write through [ 61.858918] sd 8:0:0:0: [sdc] Attached SCSI disk [ 69.875809] usb 4-3: USB disconnect, device number 4 [ 70.275816] usb 4-3: new SuperSpeed USB device number 5 using xhci_hcd [ 70.293063] scsi9 : usb-storage 4-3:1.0 [ 71.292257] scsi 9:0:0:0: Direct-Access WD My Passport 0740 1003 PQ: 0 ANSI: 6 [ 71.292505] scsi 9:0:0:1: Enclosure WD SES Device 1003 PQ: 0 ANSI: 6 [ 71.293527] sd 9:0:0:0: Attached scsi generic sg2 type 0 [ 71.293668] ses 9:0:0:1: Attached Enclosure device [ 71.293758] ses 9:0:0:1: Attached scsi generic sg3 type 13 [ 73.323804] usb 4-3: USB disconnect, device number 5 [ 101.868078] ses 9:0:0:1: Device offlined - not ready after error recovery [ 101.868124] ses 9:0:0:1: Failed to get diagnostic page 0x50000 [ 101.868131] ses 9:0:0:1: Failed to bind enclosure -19 [ 101.868288] sd 9:0:0:0: [sdc] READ CAPACITY(16) failed [ 101.868292] sd 9:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 101.868296] sd 9:0:0:0: [sdc] Sense not available. [ 101.868428] sd 9:0:0:0: [sdc] READ CAPACITY failed [ 101.868434] sd 9:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 101.868439] sd 9:0:0:0: [sdc] Sense not available. [ 101.868468] sd 9:0:0:0: [sdc] Write Protect is off [ 101.868473] sd 9:0:0:0: [sdc] Mode Sense: 00 00 00 00 [ 101.868580] sd 9:0:0:0: [sdc] Asking for cache data failed [ 101.868584] sd 9:0:0:0: [sdc] Assuming drive cache: write through [ 101.868845] sd 9:0:0:0: [sdc] READ CAPACITY(16) failed [ 101.868849] sd 9:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 101.868854] sd 9:0:0:0: [sdc] Sense not available. [ 101.868894] sd 9:0:0:0: [sdc] READ CAPACITY failed [ 101.868898] sd 9:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 101.868903] sd 9:0:0:0: [sdc] Sense not available. [ 101.868961] sd 9:0:0:0: [sdc] Asking for cache data failed [ 101.868966] sd 9:0:0:0: [sdc] Assuming drive cache: write through [ 101.868969] sd 9:0:0:0: [sdc] Attached SCSI disk Now, if I plug the same drive to the powered usb 2.0 hub of my monitor, the issue is not reproduced (at least on a 20h long operation). Also the issue of the usb reconnects is less frequent if the hard drive is plugged before I switch on the computer. Does anybody have some advice as to what I could do? Which is the faulty part/s that I should replace? As for me, I really don't know if to point my finger to the PSU or the Motherboard (I have updated to the latest firmware and checked the BIOS settings several times). EDIT: The reconnects are happening both in the Sata connected drives and the USBX connected drives.

  Read the article

• Custom built machine has much higher power consumption than expected

  - by foraidt

  I built a machine according to the specs of a computer magazine (c't, Germany). According to the magazine, the power consumption should be at around 10W. I don't want to go into the specifics of the hardware but rather ask for general advice on where to look: I updated the BIOS/UEFI version to the latest version, installed all the recommended drivers and unplugged all hardware that's not necessary to boot into Windows. All that was left is the power supply, mainboard, cpu, cpu cooler and one SSD drive. But still I measured a power consumption of 50W, which is 40W more than it should be. I tried booting Linux Mint from a USB stick, so I don't think it's some Windows-related problem.. Where else could I look? Update 1 I dind't want the question to get closed for being too localized but if more details are necessary, here they are: The system is a desktop PC. The power consumption is measured using a Brennenstuhl PM 231 device, which was tested also by c't and they found it quite accurate. The PSU is an Enermax ETL300AWT, the mainboard Intel DH87RL (Socket 1150) and the CPU Intel G3220 (Haswell). Update 2 There is no online version of the article*. The most details I found can be read on its project page (in German, though...) (*)You can pay for downloadable PDFs, however. English translation of that project page Update 3 Regarding the sceptics: It may sound ridiculous but apparently 10W idle consumption is possible with Intel's Haswell architecture. As a kind of proof, there's an additional Blog article explicitly listing the steps needed to reduce the idle consumption to 10W. Additional hardware: I measured the consumption without the HDD, and as expected the usage dropped by around 10W. I have no chassis fans and the CPU fan is a "Scythe Mugen 4" model. It runs at around 600rpm so I think it won't draw much. When stripping off all my extra components I should be at 10W. But I'm not getting anywhere near that. I would be happy to see "just" 15W in the stripped down version but currently I'm not getting below 50W no matter which component I remove. As I see it this cannot be explained by the PSU being less efficient at lower consumption. I also waited half an hour or so (also checked that no Windows updates were running in the background) and the consumption dind't drop by more than a few watts.

  Read the article

• Why do my Application Compatibility Toolkit Data Collectors fail to write to my ACT Log Share?

  - by Jay Michaud

  I am trying to get the Microsoft Application Compatibility Toolkit 5.6 (version 5.6.7320.0) to work, but I cannot get the Data Collectors to write to the ACT Log Share. The configuration is as follows. Machine: ACT-Server Domain: mydomain.example.com OS: Windows 7 Enterprise 64-bit Edition Windows Firewall configuration: File and Printer Sharing (SMB-In) is enabled for Public, Domain, and Private networks ACT Log Share: ACT Share permissions*: Group/user names Allow permissions --------------------------------------- Everyone Full Control Administrator Full Control Domain Admins Full Control Administrators Full Control ANONYMOUS LOGON Full Control Folder permissions*: Group/user name Allow permissions Apply to ------------------------------------------------- ANONYMOUS LOGON Read, write & execute This folder, subfolders, and files Domain Admins Full control This folder, subfolders, and files Everyone Read, write & execute This folder, subfolders, and files Administrators Full control This folder, subfolders, and files CREATOR OWNER Full control Subfolders and files SYSTEM Full control This folder, subfolders, and files INTERACTIVE Traverse folder / This folder, subfolders, and files execute file, List folder / read data, Read attributes, Read extended attributes, Create files / write data, Create folders / append data, Write attributes, Write extended attributes, Delete subfolders and files, Delete, Read permissions SERVICE (same as INTERACTIVE) BATCH (same as INTERACTIVE) *I am fully aware that these permissions are excessive, but that is beside the point of this question. Some of the clients running the Data Collector are domain members, but some are not. I am working under the assumption that this is a Windows file sharing permission issue or a network access policy issue, but of course, I could be wrong. It is my understanding that the Data Collector runs in the security context of the SYSTEM account, which for domain members appears on the network as MYDOMAIN\machineaccount. It is also my understanding from reading numerous pieces of documentation that setting the ANONYMOUS LOGON permissions as I have above should allow these computer accounts and non-domain-joined computers to access the share. To test connectivity, I set up the Windows XP Mode virtual machine (VM) on ACT-Server. In the VM, I opened a command prompt running as SYSTEM (using the old "at" command trick). I used this command prompt to run explorer.exe. In this Windows Explorer instance, I typed \ACT-Server\ACT into the address bar, and then I was prompted for logon credentials. The goal, though, was not to be prompted. I also used the "net use /delete" command in the command prompt window to delete connections to the ACT-Server\IPC$ share each time my connection attempt failed. I have made sure that the appropriate exceptions are Since ACT-Server is a domain member, the "Network access: Sharing and security model for local accounts" security policy is set to "Classic - local users authenticate as themselves". In spite of this, I still tried enabling the Guest account and adding permissions for it on the share to no effect. What am I missing here? How do I allow anonymous logons to a shared folder as a step toward getting my ACT Data Collectors to deposit their data correctly? Am I even on the right track, or is the issue elsewhere?

  Read the article

• Why does unpartitioned Hitachi HDS5C3020 drive start consuming 50% more power 15 minutes after boot?

  - by Pro Backup

  In a Debian 6.0.6 system there are 74 pieces of 2TB Toshiba DT01ABA200 drives. These drives are identified as Hitachi HDS5C3020BLE630 drives running firmware revision MZ4OAAB0. 64 Drives attached via HP SAS expander cards to an LSI 2008 SAS controller, another 5 drives are connected directly to the mainboard, 4 drives are connected to a Sil based PCI controller and last 1 drive is only powered and has no data cable connected. The controller LSI and Sil card's their onboard BIOS are both disabled and the mpt2sas and sata_sil modules are removed from the Linux debian 2.6.32-5-amd64 #1 SMP Sun Sep 23 10:07:46 UTC 2012 x86_64 GNU/Linux kernel. The mpt2sas module is loaded after boot using a modprobe command in /etc/rc.local. These 74 drives are not partitioned, neither formatted and also not mounted. The system consumes: with 0 drives: 70.6 - 70.9 Watt (also 15 minutes after boot); with 74 drives: 330 - 360 Watt, just after boot (is equivalent to 3.5 - 3.9W per drive in idle state); with 74 drives: 420 - 466 Watt, each time in the 15th minute of uptime (is equivalent to 4.7 - 5.3W per drive in idle state). The drive specification lists 4.7W as read/write, and 3.3W as idle power consumption. The increased power consumption is most likely on the 5V line, because after roughly 1 minute an "over current protection" (OCP) of the power supply (PSU) shuts down the power. The used PSU is a single rail model with an OCP of 122A on the 12V line and 55A on the 5V line. Regression: It doesn't matter whether the drive its APM value is set to disabled or 1 (maximum power saving). The operating system records no read/write activity in /proc/diskstats. The values there are identical (28 read, 0 write operations) as immediately after the modprobe operation. Can't test what happens when booting into the mainboard it's BIOS - to exclude any OS intervention - because the Super Micro X8SI6-F mainboard running firmware 06/27/12 has a bug that incorrectly reads a +74.0 C CPU sensor temperature as "High" in BIOS mode, and shuts down the power after 1 minute. What might be causing the drive read/write activity on all drives in the 15th minute after boot and how to prevent it from happening?

  Read the article

• Why do some games randomly turn my screen a random solid color?

  - by Emlena.PhD

  When playing some games my computer will randomly have an error that I cannot fix without turning it off and back on again. The screen changes to one solid color, which varies (off the top of my head I can remember seeing solid green, magenta, etc..) and the sound blares a single tone. The sound sometimes briefly restores and I can still hear the game sounds and even hear and still be heard by people in my Mumble channel, but the screen doesn't right itself so I'm still blind. What's more is this happens in some games but not in others. While the game is actually running, not while I'm still in the menu. However, it does happen if I'm afk or idle but the game world is still rendering. Games where the error occurs: League of Legends World of Warcraft Trine The Sims 2 Dungeon Defenders Safe games: games where it has never occurred: Tribes: Ascend Star Wars: the Old Republic Battlefield 3 So relatively older games cause the problem while newer games do not? I cannot predict when it will happen, it just seems random. However, if it happens and I try playing the same game further after restart it does appear to occur more frequently after the first time. But if I switch to a safe game it doesn't continue happening. Both of my RAM sticks appear fine, flipped position or either one on their own and games still run, computer still boots. I would think over-heating, but then why not all games? ALso, sometimes it happens immediately after I start playing, within seconds of the 3D world booting up. I'm looking to upgrade very soon so I want to figure out what component or software is fubar and replace/repair it. Any suggestions or recommendations of tools would be helpful. Below is some system information. Dxdiag does not detect any problems. Operating System: Windows 7 Home Premium 64-bit (6.1, Build 7601) Service Pack 1 (7601.win7sp1_gdr.120305-1505) System Manufacturer: Gigabyte Technology Co., Ltd. System Model: EP45-UD3R BIOS: Award Modular BIOS v6.00PG Processor: Intel(R) Core(TM)2 Duo CPU E8500 @ 3.16GHz (2 CPUs), ~3.2GHz Memory: 4096MB RAM DirectX Version: DirectX 11 DxDiag Version: 6.01.7601.17514 64bit Unicode Graphics card name: NVIDIA GeForce GTX 285 Driver Version: 8.17.12.9610 (error has occurred w/several driver versions) Sound: I do not have a sound card, been using motherboard's built in sound)

  Read the article

• Airport Express chokes Wi-Fi for a few seconds, several times per hour. Any idea why?

  - by user13727

  I'm using a MacBookPro connected to an AiportExpress' Wi-FI network. Every once in a while, the Wi-Fi will choke up and either drop some packets, or lag horribly for several seconds. I'm losing hair over this because every time I chat on Skype, the call hangs randomly due to this problem. Any idea what's wrong? Some more details: two networks are set up: 2.4Ghz and 5Ghz, and the issue happens on both the network uses WPA2 Personal for security the Airport is in the same room with my computer the Airport is fairly new, bought this summer, model number off the back: A1392 tried connecting to a neighbours wifi to see if it's a problem with my computer, or interference. It's not, it doesn't happen on their network. tried resetting it several times tried changing channels manually Ping results are below, so you can see what I'm talking about. EDIT: 10.0.1.1 is the Airport's IP 64 bytes from 10.0.1.1: icmp_seq=1795 ttl=255 time=0.813 ms 64 bytes from 10.0.1.1: icmp_seq=1796 ttl=255 time=3.335 ms 64 bytes from 10.0.1.1: icmp_seq=1797 ttl=255 time=3.403 ms 64 bytes from 10.0.1.1: icmp_seq=1798 ttl=255 time=3.414 ms 64 bytes from 10.0.1.1: icmp_seq=1799 ttl=255 time=3.227 ms 64 bytes from 10.0.1.1: icmp_seq=1800 ttl=255 time=3.274 ms 64 bytes from 10.0.1.1: icmp_seq=1801 ttl=255 time=3.253 ms 64 bytes from 10.0.1.1: icmp_seq=1802 ttl=255 time=3.292 ms >>>> choke starts <<< 64 bytes from 10.0.1.1: icmp_seq=1803 ttl=255 time=53.977 ms 64 bytes from 10.0.1.1: icmp_seq=1804 ttl=255 time=35.049 ms 64 bytes from 10.0.1.1: icmp_seq=1805 ttl=255 time=19.820 ms >>>> choke ends <<< 64 bytes from 10.0.1.1: icmp_seq=1806 ttl=255 time=0.716 ms 64 bytes from 10.0.1.1: icmp_seq=1807 ttl=255 time=0.705 ms 64 bytes from 10.0.1.1: icmp_seq=1808 ttl=255 time=0.919 ms 64 bytes from 10.0.1.1: icmp_seq=1809 ttl=255 time=0.659 ms 64 bytes from 10.0.1.1: icmp_seq=1810 ttl=255 time=0.877 ms 64 bytes from 10.0.1.1: icmp_seq=1811 ttl=255 time=0.679 ms 64 bytes from 10.0.1.1: icmp_seq=1812 ttl=255 time=0.854 ms 64 bytes from 10.0.1.1: icmp_seq=1813 ttl=255 time=0.644 ms 64 bytes from 10.0.1.1: icmp_seq=1814 ttl=255 time=3.779 ms ... time passes .. 64 bytes from 10.0.1.1: icmp_seq=1599 ttl=255 time=0.674 ms 64 bytes from 10.0.1.1: icmp_seq=1600 ttl=255 time=0.930 ms 64 bytes from 10.0.1.1: icmp_seq=1601 ttl=255 time=0.665 ms 64 bytes from 10.0.1.1: icmp_seq=1602 ttl=255 time=1.085 ms Request timeout for icmp_seq 1603 Request timeout for icmp_seq 1604 64 bytes from 10.0.1.1: icmp_seq=1605 ttl=255 time=104.969 ms 64 bytes from 10.0.1.1: icmp_seq=1606 ttl=255 time=11.521 ms 64 bytes from 10.0.1.1: icmp_seq=1607 ttl=255 time=0.926 ms 64 bytes from 10.0.1.1: icmp_seq=1608 ttl=255 time=0.993 ms 64 bytes from 10.0.1.1: icmp_seq=1609 ttl=255 time=0.745 ms And the Signal-Noise ratio:

  Read the article

• Mixed sessions with Classic ASP on IIS 7.5 and Windows 2008 R2 64 bit

  - by Marcin

  Recently had an issues with a server upgrade from IIS 6 on Windows 2003 to IIS 7.5 on Windows 2008 R2 64 bit. We have a number of websites running on Classic ASP. All the sites sit under a particular site, e.g. www.example.com/foo and www.example.com/foobar. On IIS 6 each site was set up as a virtual directory and things worked fine. Since moving to the new set up, a lot of websites seem to have mixed Sessions. To be clear, this is not a app pool recycling issue; rather the sessions are populated with information when the user hits the site and while browsing they get sessions from different sites. We've determined this based on - a few customers called up and reported having their shopping cart with items with names of items belonging to a different site - also our own testing showed that some queries being run would try to bring products in from a different site We've tried - disabling dynamic caching - converting each site to be a virtual application (if I understand correctly, the virtual directory/application concepts were changed/refined somewhat in IIS 7 although to be honest, I'm not clear what the difference is) - various application pool changes (using .NET 2 framework), classic and integrated modes, changing the Process model to NetworkIdentity), all to no avail. The only thing we haven't tried is changing it to run as a 32 bit application. We're not using http only cookies, so when I open up a browser and type document.cookie into the dev console in Firefox/Chrome/IE that there will be multiple ASPSESSIONID=... values whereas previously I believe there was only one. Finally, we use server side JScript for the classic ASP pages, not VBScript, so we have code similar to the below. //the user's login account as a jscript object Session("user") = { email : "[email protected]", id : 123 }; and if we execute a line of code like below: Response.Write( typeof(Session("user")) ); When things are running correctly, we get "object" - as expected. When the Session gets trashed, the output is "unknown" and we are also unable to access the fields within the JScript object (e.g. the .email or .id fields). Much appreciated if anyone can provide any pointers about how to resolve this, everything on google seems to point to different issues.

  Read the article

• Can't save screen resolution setting.

  - by Searock

  Hi, My screen resolution in windows and previous version of Ubuntu (9.04) was 1152 x 864. But in Ubuntu 10.04 it gives me an option of 1024 x 786 and 1360 x 786. I have some how managed to add 1152x684 resolution by using xrandr command. searock@searock-desktop:~$ cvt 1152 864 1152x864 59.96 Hz (CVT 1.00M3) hsync: 53.78 kHz; pclk: 81.75 MHz Modeline "1152x864_60.00" 81.75 1152 1216 1336 1520 864 867 871 897 -hsync +vsync searock@searock-desktop:~$ xrandr --newmode "1152x864_60.00" 81.75 1152 1216 1336 1520 864 867 871 897 -hsync +vsync searock@searock-desktop:~$ xrandr --addmode S-video 1152x864 xrandr: cannot find output "S-video" searock@searock-desktop:~$ xrandr Screen 0: minimum 320 x 200, current 1024 x 768, maximum 4096 x 4096 VGA1 connected 1024x768+0+0 (normal left inverted right x axis y axis) 0mm x 0mm 1360x768 59.8 1024x768 60.0* 800x600 60.3 56.2 848x480 60.0 640x480 59.9 59.9 1152x864_60.00 (0x124) 81.0MHz h: width 1152 start 1216 end 1336 total 1520 skew 0 clock 53.3KHz v: height 864 start 867 end 871 total 897 clock 59.4Hz searock@searock-desktop:~$ xrandr --addmode VGA1 1152x864_60.00 But the problem is when ever I restart my computer I get this message. Could not apply the stored configuration for the monitors. Could not find a suitable configuration of screens. And then it comes back to 1024 x 786 My graphic card details : Intel(R) 82945G Express Chipset Family. Is there any way I can fix this once for all ? Thanks. Edit 1 : rumtscho has suggested me to modify xorg.conf file. But I am not sure what HorizSync means? is it Horizontal frequency ? My monitor model is Acer v173. Here's my specification. So what should be HorizSync and VertRefresh ? Edit 2 : I have edited my Xorg.conf file as follows : Section "Monitor" Identifier "Configured Monitor" HorizSync 30-80 VertRefresh 55-75 EndSection then I added the resolution and restarted my computer and still I am facing the same problem. Is there something that I am missing? Edit 3 : For now I have edited /etc/gdm/Init/Default(gdm startup scripts) to include following xrandr commands, just below line initctl -q emit login-session-start DISPLAY_MANAGER=gdm xrandr --newmode "1152x864_60.00" 81.75 1152 1216 1336 1520 864 867 871 897 -hsync +vsync xrandr --addmode VGA1 1152x864_60.00<br/> xrandr -s 1152x864_60.00 This has solved my problem, but this commands have increased my computer's boot time. I think I will have to edit xorg file properly. Edit 4 : Instead of adding this files to gdm startup scripts I have created a shell script and added it to startup (System - Preference - Startup Applications) #!/bin/bash xrandr --newmode "1152x864_60.00" 81.75 1152 1216 1336 1520 864 867 871 897 -hsync +vsync xrandr --addmode VGA1 1152x864_60.00 xrandr -s 1152x864_60.00 And don't forget to add execution rights. (Right Click - Properties - Permission - Allow executing file as program)

  Read the article

< Previous Page | 545 546 547 548 549 550 551 552 553 554 555 556  | Next Page >