Search Results

Search found 8647 results on 346 pages for 'intel cpu'.

Page 55/346 | < Previous Page | 51 52 53 54 55 56 57 58 59 60 61 62  | Next Page >

• Software/FakeRAID: Windows 8 Disk Mirroring vs Intel Onboard

  - by Johnny W

  So Windows 8 is out and I have a new motherboard. I wish to create a RAID 1 coupling between two HDDs -- for storage purposes only (my OS is on an SSD) -- but I don't know which is the best route to take. My motherboard (Z77 chipset) comes with the age old Intel Fake RAID, but since I only wish to use my RAID for storage, I wondered if I might be better to use Windows 8 Disk Mirroring. Can anyone advise which is better? Or perhaps the pros and cons of each, if that's too contentious? I just can't see the benefit of FakeRAID. You can see my current setup here, if that might change things(?): Thanks!

  Read the article

• Intel Rapid Storage Technology - Raid5 is very slow

  - by Cederstrom

  Hi, I build a computer with a raid5, using the motherboards raid controller (ASUS P7H57D-V EVO - intel Rapid Storage Technology). The read and write are however very slow, when using the raid controller :( - I am using Windows 2008 R2, and when using the windows software raid, it was ok in speed - so there must be an issue with the controller? Im using 6 disks on 2TB each. Do anyone have any idea why its so slow, and how to fix it? I rather not pick the easy solutiuon of "just buy a raid controller" :| If you need more info about my setup, please just ask. Thanks :)

  Read the article

• PC wont boot with more than 1 stick of RAM.

  - by Aidan

  Hi Guys, I've got the following computer and I've just put in a new CPU QX9650 and I've run into this problem since making this hardware change. Whenever I put more than 1 of my 4 sticks of ram into my machine it wont load an OS. It'll go through the BIOS but BSOD on windows load. It also wont let me install an OS from disk or boot into Linux. I've ran memtest with all 4 sticks in and I get 10k+ errors on test5. Each stick of ram on it's own is fine and functions properly. I only have problems when all 4 sticks are in the machine at the same time. System specs.. CPU: QX9650 Mobo: Asus P5B 2104 BIOS RAM: 2xPC25400 DDR2 , 2xPC2 6400 both OCZ. Is the problem on my end or is the CPU faulty?

  Read the article

• PC wont boot with more than 1 stick of RAM.

  - by Aidan

  Hi Guys, I've got the following computer and I've just put in a new CPU QX9650 and I've run into this problem since making this hardware change. Whenever I put more than 1 of my 4 sticks of ram into my machine it wont load an OS. It'll go through the BIOS but BSOD on windows load. It also wont let me install an OS from disk or boot into Linux. I've ran memtest with all 4 sticks in and I get 10k+ errors on test5. Each stick of ram on it's own is fine and functions properly. I only have problems when all 4 sticks are in the machine at the same time. System specs.. CPU: QX9650 Mobo: Asus P5B 2104 BIOS RAM: 2xPC25400 DDR2 , 2xPC2 6400 both OCZ. Is the problem on my end or is the CPU faulty?

  Read the article

• Intel SASWT4I SAS/SATA Controller Question

  - by Joe Hopfgartner

  Hey there! I want to assemble a cheap storage sytem based on the Norco RPC-4020 Case. When searching for controllers I found this one: Intel® RAID Controller SASWT4I This is a quote form the Spec Sheet: Scalability. Supports up to 122 physical devices in SAS mode which is ideal for employing JBODs (Just a Bunch Of Disks) or up to 14 devices in RAID 0, 1, 1E/10E mode through direct connect device attachment or through expander backplane support. Does that mean I can attatch 14 SATA drives directly to the controller using SFF-8087 - 4x SATA breakout cables? That would be nice because then I can choose a mainboard that has 6 Onboard SATA and i can connect all 20 bays while only spending 155$ on the controller and like another 100$ on cables. Would that work? And why is it 14 and not 16 when there are 4 Ports? I am really confused about all the breakout/fanout/(edge-)expanding/multiplying/channel stuff...

  Read the article

• Intel HD 4000 driver not working

  - by Sagar Parakh

  I have a Dell Inspiron 15r se 7520. I have upgraded my system to Windows 8.1 few days back. After the upgrade, my Intel HD 4000 graphics driver stopped working. I have downloaded the latest driver from Dell website but during installation it said that my graphics driver is not compatible or validated and also my dedicated graphics driver AMD ATI Raedon HD 7730m also stopped working. There is also a problem with my screen brightness: I am unable to change it. How to make my graphics driver work?

  Read the article

• performance monitoring

  - by Sunny

  I want to monitor CPU usage, disk read/write usage for a particular process, say ./myprocess. To monitor CPU top command seems to be a nice option and for read and write iotop seems to be a handy one. For example to monitor read/write for every second i use the command iotop -tbod1 | grep "myprocess". My difficulty is I just want only three variables to store, namely read/sec, write/sec, cpu usage/sec. Could you help me with a script that combines the outputs the above said three variables from top and iotop to be stored into a log file? Thanks!

  Read the article

• Assembling a number-crunching computer [closed]

  - by tugrul büyükisik

  What is needed to make a GPU fully fed by CPU? Comparing their flops/s is enough? For example, if i could manage to make a very old(pentium-3) CPU with one of Nvidia-Fermi GPU, it would not be able to fed the gpu with data per sec. What is the criteria to fit CPU to GPU exactly when OpenCL or some similar work needed? Of course RAM and BUS will be chosen in a similar way but how exactly? Assume each GPU-core will calculate a sqrt and a division and an adding for 100 times for every itearation. Thanks.

  Read the article

• IIS 7 Application Pools using a different amount of memory on multiple servers behind a load balancer

  - by Jim March

  We have 6 servers in a web farm behind an F5. There are approximately 25 AppPools on each of these servers. On servers 1 - 5 the apppools are consuming approx 500MB Private Bytes, and 5GB Virtual Bytes. On server 6 the apppools are consuming approx 800MB Private Bytes, and 8GB Virtual Bytes. I can not seem to figure out why we have this difference. The code is the exact same on each box. We replicate the apphost.config between the boxes, so the Appplication Configs are identical. The only difference seems to be that this box consumes more RAM, and in turn ends up using a lot more CPU. During Black Friday we observed the CPU on server 6 spiking to 100% and noticed that the % Memory Commit was also near 100%, while the rest of the farm was at closer to 50% utilization. Pulling the 6th server from the load balancer dropped CPU/Memory on the 6th server back to normal, and did not cause a noticeable strain on the other servers.

  Read the article

• Experience with Intel X25-M 160GB and Oracle

  - by derobert

  We're considering building an Oracle database with 12 Intel X25-M G2 160GB drives in software RAID10. It'd be running Linux. Database gets some very heavy write activity during the early morning data load, other than that it is mostly read-only (and the read load is fairly minimal). We're currently running on 11 150GB Velociraptors (also Linux software RAID10), and are hoping the X25-M will speed up the data load. We currently have redo on different disks than the rest of the data. I'm wondering a few things: Any experience with using X25-M drives for databases? The X25-E are unfortunately beyond our budget. Would it hurt to separate redo off to some magnetic (non-SSD) drives, say 2 (raid1) or 4 (raid10) Seagate Constellations?

  Read the article

• xen virtual machines get to many porcentages of cpus

  - by ki0

  Hi everyone, This is my question. I have one Xen server with 8 CPU's and 6 virtual machine running, each virtual hard disk are running in diferent physical hardisk. Everything worked fine but sometimes one virtual machine get almost whole CPU, if the Domain-0 is 90% that is normal, the virtual machine is 500% usage of CPU. I have improved that it is not depends who are working with the VM even when nobody are working with the server this still happens. I dont know what happen. Anyone have any idea?¿ or anyone have happened the same?¿

  Read the article

• Asus x551c windows 7 Intel HD Graphics driver

  - by user3609459

  I did install Windows 7 64 bit on my ex. Windows 8 pro Asus x551c "Ultrabook". The CD with the drivers isn't useable since its a windows 8 only DVD-Rom. I got the Wi-Fi and other stuff running and already tryed 3 of the Intel-HD Graphic drivers for win7 64Bit i found with google. No one was compatible with my pc. Any suggestions how to get this running? I hate windows 8 and dont want to get forced to use it.

  Read the article

• What's going on with my wireless?

  - by Mark Scott

  The WiFi on my Acer laptop (it's a 3810TZ, with Intel Corporation Centrino Wireless-N 1000) works flawlessly on Ubuntu 11.04. On 11.10, it's continually up and down, and it fills the system log with messages such as those below. What is going on? It seems to be unable to decide which regulatory domain it's in. Despite the system configuration being quite clearly set to UK it persists in configuring itself as though it was opeating in Taiwan! Nov 22 15:34:37 MES3810 wpa_supplicant[1053]: WPA: 4-Way Handshake failed - pre-shared key may be incorrect Nov 22 15:34:37 MES3810 wpa_supplicant[1053]: CTRL-EVENT-DISCONNECTED bssid=00:50:7f:72:bf:b0 reason=15 Nov 22 15:34:37 MES3810 wpa_supplicant[1053]: CTRL-EVENT-DISCONNECTED bssid=00:00:00:00:00:00 reason=3 Nov 22 15:34:37 MES3810 kernel: [18239.240355] cfg80211: All devices are disconnected, going to restore regulatory settings Nov 22 15:34:37 MES3810 kernel: [18239.240362] cfg80211: Restoring regulatory settings Nov 22 15:34:37 MES3810 kernel: [18239.240368] cfg80211: Calling CRDA to update world regulatory domain Nov 22 15:34:37 MES3810 kernel: [18239.240408] wlan0: deauthenticating from 00:50:7f:72:bf:b0 by local choice (reason=3) Nov 22 15:34:37 MES3810 NetworkManager[875]: (wlan0): supplicant interface state: 4-way handshake - disconnected Nov 22 15:34:37 MES3810 kernel: [18239.246556] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain Nov 22 15:34:37 MES3810 kernel: [18239.246563] cfg80211: World regulatory domain updated: Nov 22 15:34:37 MES3810 kernel: [18239.246567] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) Nov 22 15:34:37 MES3810 kernel: [18239.246572] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Nov 22 15:34:37 MES3810 kernel: [18239.246577] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) Nov 22 15:34:37 MES3810 kernel: [18239.246582] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) Nov 22 15:34:37 MES3810 kernel: [18239.246587] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Nov 22 15:34:37 MES3810 kernel: [18239.246592] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Nov 22 15:34:37 MES3810 NetworkManager[875]: (wlan0): supplicant interface state: disconnected - scanning Nov 22 15:34:37 MES3810 wpa_supplicant[1053]: Trying to authenticate with 00:50:7f:72:bf:b0 (SSID='PoplarHouse' freq=2412 MHz) Nov 22 15:34:37 MES3810 NetworkManager[875]: (wlan0): supplicant interface state: scanning - authenticating Nov 22 15:34:37 MES3810 kernel: [18239.509877] wlan0: authenticate with 00:50:7f:72:bf:b0 (try 1) Nov 22 15:34:37 MES3810 wpa_supplicant[1053]: Trying to associate with 00:50:7f:72:bf:b0 (SSID='PoplarHouse' freq=2412 MHz) Nov 22 15:34:37 MES3810 kernel: [18239.512276] wlan0: authenticated Nov 22 15:34:37 MES3810 kernel: [18239.512615] wlan0: associate with 00:50:7f:72:bf:b0 (try 1) Nov 22 15:34:37 MES3810 NetworkManager[875]: (wlan0): supplicant interface state: authenticating - associating Nov 22 15:34:37 MES3810 kernel: [18239.516508] wlan0: RX ReassocResp from 00:50:7f:72:bf:b0 (capab=0x431 status=0 aid=1) Nov 22 15:34:37 MES3810 kernel: [18239.516514] wlan0: associated Nov 22 15:34:37 MES3810 wpa_supplicant[1053]: Associated with 00:50:7f:72:bf:b0 Nov 22 15:34:37 MES3810 kernel: [18239.529097] cfg80211: Calling CRDA for country: TW Nov 22 15:34:37 MES3810 NetworkManager[875]: (wlan0): supplicant interface state: associating - associated Nov 22 15:34:37 MES3810 kernel: [18239.535680] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule: Nov 22 15:34:37 MES3810 kernel: [18239.535688] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi, 2700 mBm) Nov 22 15:34:37 MES3810 kernel: [18239.535692] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule: Nov 22 15:34:37 MES3810 kernel: [18239.535697] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi, 2700 mBm) Nov 22 15:34:37 MES3810 kernel: [18239.535702] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule: Nov 22 15:34:37 MES3810 kernel: [18239.535707] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi, 2700 mBm) Nov 22 15:34:37 MES3810 kernel: [18239.535711] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule: Nov 22 15:34:37 MES3810 kernel: [18239.535716] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi, 2700 mBm) Nov 22 15:34:37 MES3810 kernel: [18239.535720] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule: Nov 22 15:34:37 MES3810 kernel: [18239.535725] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi, 2700 mBm) Nov 22 15:34:37 MES3810 kernel: [18239.535730] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule: Nov 22 15:34:37 MES3810 kernel: [18239.535735] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi, 2700 mBm) Nov 22 15:34:37 MES3810 kernel: [18239.535739] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule: Nov 22 15:34:37 MES3810 kernel: [18239.535744] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi, 2700 mBm) Nov 22 15:34:37 MES3810 kernel: [18239.535748] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule: Nov 22 15:34:37 MES3810 kernel: [18239.535753] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi, 2700 mBm) Nov 22 15:34:37 MES3810 kernel: [18239.535757] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule: Nov 22 15:34:37 MES3810 kernel: [18239.535763] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi, 2700 mBm) Nov 22 15:34:37 MES3810 kernel: [18239.535767] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule: Nov 22 15:34:37 MES3810 kernel: [18239.535772] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi, 2700 mBm) Nov 22 15:34:37 MES3810 kernel: [18239.535777] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule: Nov 22 15:34:37 MES3810 kernel: [18239.535782] cfg80211: 2402000 KHz - 2472000 KHz @ KHz), (300 mBi, 2700 mBm) Nov 22 15:34:37 MES3810 kernel: [18239.535786] cfg80211: Disabling freq 2467 MHz Nov 22 15:34:37 MES3810 kernel: [18239.535789] cfg80211: Disabling freq 2472 MHz Nov 22 15:34:37 MES3810 kernel: [18239.535794] cfg80211: Regulatory domain changed to country: TW Nov 22 15:34:37 MES3810 kernel: [18239.535797] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) Nov 22 15:34:37 MES3810 kernel: [18239.535802] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) Nov 22 15:34:37 MES3810 kernel: [18239.535807] cfg80211: (5270000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) Nov 22 15:34:37 MES3810 kernel: [18239.535812] cfg80211: (5735000 KHz - 5815000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) Nov 22 15:34:38 MES3810 NetworkManager[875]: (wlan0): supplicant interface state: associated - 4-way handshake Any ideas?

  Read the article

• AWStats on Plesk consumes all of CPU and crashes server - how do you disable plesk

  - by columbo

  I have Plesk 9.0.1 running on a Red Hat server. Every week or so at about 4:10 AM the server locks up. At this time the server CPU usage shoots from 4% to 90% at the same time as a mass of awstats.pl processes start (I can't see how many as my datat only shows the top 30 processes, but all of these are awstats.pl). I turned off awstats through the Plesk control panel for all but 5 domains but I still get 90% CPU usage and at least 30 instances of awstats.pl happening at 4:10am as usual. Does anyone know why this may be? Does anyone know how to disable awstats (I have stats covered using piwik)? Or how do I uninstall awstats without snarling up Plesk?

  Read the article

• IIS, multiple CPU cores, application pools and worker processes - best configuration for a single si

  - by Egghead Design

  Hi We use Kentico CMS and I've exchanged emails with them about a web garden deployment. We have a single site running on a server with 8 cpu cores. In line with Kentico's advice, we have not altered the application pool web garden setting from the default i.e. it is set to a maximum number of worker processes of 1. Our experience is that the site only uses one of the cpu cores - the others are idling. When I emailed them about this, their response was that the OS/IIS would handle this and use other cores as necessary even though the application pool only has a single worker process. Now, I've a lot of respect for the guys at Kentico, but this doesn't seem right to me? Surely, if we want to use all cores, we need to permit eight worker processes (and implement session state storage in SQL server)? Many thanks Tony

  Read the article

• php-cgi cpu usage is super high

  - by Ryan Thompson

  I am getting constantly high and wildly fluctuating CPU usage % for php-cgi commands as seen via "top" on my Centos server.. I have a server density account and it seems that this is a common trend: User - PID - CPU % - MEM % - VSZ - RSS - TT - Stat - Started - Time - Command 500 - 6389 - 22.4 - 3 - 271136 - 32380 - ? - S - 20:26 - 0:40 - /usr/bin/php-cgi Seems there are about 6 or so of those records in my processes list at any given check-in. Any ideas what's causing this? I have fast_cgi installed and the module is loading.. Not sure why it isn't handling this though. Any help would be greatly appreciated! Ryan

  Read the article

• Postgres 9.0 locking up, 100% CPU

  - by Jake

  We are having a problem where our Postgres 9.0 server occasionally locks up and kills our webapp. Restarting Postgres fixes the problem. Here's what I've been able to observe: First, usage of one CPU jumps to 100% for a few minutes Disk operations drop to ~0 during this time Database operations drop to 0 (blocks and tuples per sec) Logs show during this time: WARNING: worker took too long to start; cancelled WARNING: worker took too long to start; cancelled No Queries in logs (only those over 200ms are logged) No unusually long-running queries logged before or during Then the second CPU jumps to 100% The number of postgres processes jumps from the usual 8-10 to ~20 Matched by a spike in Postgres Blocks per second (about twice normal) Logs show LOG: could not accept SSL connection: EOF detected Queries are running but slow Restarting postgres returns everything to normal Setup: Server: Amazon EC2 Large Ubuntu 10.04.2 LTS Postgres 9.0.3 Dedicated DB server Does anyone have any idea what's causing this? Or any suggestions about what else I should be checking out?

  Read the article

• Windows / Apache / PHP CPU at 100% under small load

  - by Bart

  I have a Windows box loaded with Apache 2.2 and PHP 5.2. It runs great if only a few users are on it at a time, but under load testing (50 users for test #1), the CPU climbs up to 100%. Nearly all of this CPU usage comes from httpd.exe. I currently have PHP set up via php5_module, but one of the first things I plan to try next is to use FastCGI instead. Is FastCGI better at handling multiple connections? Any other ideas on what might be causing Apache to run so high?

  Read the article

• Slowing down cpu speed

  - by New linux user

  How to slow down my laptop cpu so that it does not overheat?

  Read the article

• CPU I/O communication

  - by b-gen-jack-o-neill

  Hi, I know there is this question already discussed, but I still don´t understand something, so please just help me clarify it. What I understand there is 2 way to do I/O aka communicate from CPU with other HW. One is to use in and out instructions, and second is the memory mapped. But what I don´t actually understand is, is IN and OUT instructions are used, you define source port. But what is this port? I mean, is it different set of pins on CPU or what? And, to what is that port connected? And for the memory mapped, I miss just a tiny detail. Wheather memory mapped I/O must be first set by IN and OUT instructions, or does the device actually somehow itself connects to the RAM and reads it? Thanks.

  Read the article

• sar command to generate only CPU utilization and network statistics in Linux

  - by Vijay Shankar Kalyanaraman

  I want to be able to generate the system activity report every 30 seconds or every minute and store in a file and use it for diagnostic purposes on my VM. So I give an output file for the sar command and read it using the "-f" option. But I only use the CPU utilization and network utilization part of the report and so rest is all that I don't want to save (waste the space in the disk to store these reports). Also the sar files that are generated are all binary. Is there a way to collect these stats for the CPU and network utilization alone? and so save almost 2/3rds the space on the disk?

  Read the article

• Finding throuput of CPU and Hardrive on Solaris

  - by Jim

  How do i find the throughput of a CPU and the Hardisk on an open solaris machine. Using MPstat or iostat. I'm having a hard time identifying the throughput if it is given at all in the commands output. Eg. in mpstat there is very little explanation as to what the columns mean http://docs.sun.com/app/docs/doc/816-5166/mpstat-1m?l=en&a=view&q=syscl+mpstat I've been using the syscl column divided by time interval to find the throughput but to be honest i have no idea what a system call truelly is. I'm trying to to analyze a hardrive and CPU while writing a file to the hardisk and when at rest Thanks in advance. Jim

  Read the article

• Work around for yahoo mail slowness (using 100% cpu)

  - by Tony Lee

  My yahoo mail is very slow sometimes. When it is, I notice that IE8 is using 100% cpu. Using sysinternals process explorer I discovered the thread using all the cpu in IE8 has Flash in the stackwalk. I upgraded flash from 9 to 10, but the problem persists. I'm about to edit hosts to block the flash content by redirecting the yahoo and ad click dns entries. Is there some easier way to get flash to behave? The fix for the long run will be switching to gmail.

  Read the article

• How to set up linux watchdog daemon with Intel 6300esb

  - by ACiD GRiM

  I've been searching for this on Google for sometime now and I have yet to find proper documentation on how to connect the kernel driver for my 6300esb watchdog timer to /dev/watchdog and ensure that watchdog daemon is keeping it alive. I am using RHEL compatible Scientific Linux 6.3 in a KVM virtual machine by the way Below is everything I've tried so far: dmesg|grep 6300 i6300ESB timer: Intel 6300ESB WatchDog Timer Driver v0.04 i6300ESB timer: initialized (0xffffc900008b8000). heartbeat=30 sec (nowayout=0) | ll /dev/watchdog crw-rw----. 1 root root 10, 130 Sep 22 22:25 /dev/watchdog | /etc/watchdog.conf #ping = 172.31.14.1 #ping = 172.26.1.255 #interface = eth0 file = /var/log/messages #change = 1407 # Uncomment to enable test. Setting one of these values to '0' disables it. # These values will hopefully never reboot your machine during normal use # (if your machine is really hung, the loadavg will go much higher than 25) max-load-1 = 24 max-load-5 = 18 max-load-15 = 12 # Note that this is the number of pages! # To get the real size, check how large the pagesize is on your machine. #min-memory = 1 #repair-binary = /usr/sbin/repair #test-binary = #test-timeout = watchdog-device = /dev/watchdog # Defaults compiled into the binary #temperature-device = #max-temperature = 120 # Defaults compiled into the binary #admin = root interval = 10 #logtick = 1 # This greatly decreases the chance that watchdog won't be scheduled before # your machine is really loaded realtime = yes priority = 1 # Check if syslogd is still running by enabling the following line #pidfile = /var/run/syslogd.pid Now maybe I'm not testing it correctly, but I would expecting that stopping the watchdog service would cause the /dev/watchdog to time out after 30 seconds and I should see the host reboot, however this does not happen. Also, here is my config for the KVM vm <!-- WARNING: THIS IS AN AUTO-GENERATED FILE. CHANGES TO IT ARE LIKELY TO BE OVERWRITTEN AND LOST. Changes to this xml configuration should be made using: virsh edit sl6template or other application using the libvirt API. --> <domain type='kvm'> <name>sl6template</name> <uuid>960d0ac2-2e6a-5efa-87a3-6bb779e15b6a</uuid> <memory unit='KiB'>262144</memory> <currentMemory unit='KiB'>262144</currentMemory> <vcpu placement='static'>1</vcpu> <os> <type arch='x86_64' machine='rhel6.3.0'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <cpu mode='custom' match='exact'> <model fallback='allow'>Westmere</model> <vendor>Intel</vendor> <feature policy='require' name='tm2'/> <feature policy='require' name='est'/> <feature policy='require' name='vmx'/> <feature policy='require' name='ds'/> <feature policy='require' name='smx'/> <feature policy='require' name='ss'/> <feature policy='require' name='vme'/> <feature policy='require' name='dtes64'/> <feature policy='require' name='rdtscp'/> <feature policy='require' name='ht'/> <feature policy='require' name='dca'/> <feature policy='require' name='pbe'/> <feature policy='require' name='tm'/> <feature policy='require' name='pdcm'/> <feature policy='require' name='pdpe1gb'/> <feature policy='require' name='ds_cpl'/> <feature policy='require' name='pclmuldq'/> <feature policy='require' name='xtpr'/> <feature policy='require' name='acpi'/> <feature policy='require' name='monitor'/> <feature policy='require' name='aes'/> </cpu> <clock offset='utc'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/libexec/qemu-kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw'/> <source file='/mnt/data/vms/sl6template.img'/> <target dev='vda' bus='virtio'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x04' function='0x0'/> </disk> <controller type='usb' index='0'> <address type='pci' domain='0x0000' bus='0x00' slot='0x01' function='0x2'/> </controller> <interface type='bridge'> <mac address='52:54:00:44:57:f6'/> <source bridge='br0.2'/> <model type='virtio'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x0'/> </interface> <interface type='bridge'> <mac address='52:54:00:88:0f:42'/> <source bridge='br1'/> <model type='virtio'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x07' function='0x0'/> </interface> <serial type='pty'> <target port='0'/> </serial> <console type='pty'> <target type='serial' port='0'/> </console> <watchdog model='i6300esb' action='reset'> <address type='pci' domain='0x0000' bus='0x00' slot='0x06' function='0x0'/> </watchdog> <memballoon model='virtio'> <address type='pci' domain='0x0000' bus='0x00' slot='0x05' function='0x0'/> </memballoon> </devices> </domain> Any help is appreciated as the most I've found are patches to kvm and general softdog documentation or IPMI watchdog answers.

  Read the article

• Thermal risks to other components when watercooling CPU

  - by B Sharp

  I recently ordered all the components for a new desktop system to replace my old, dying computer. I wanted to have a really quiet desktop, so I got a case rated for being quiet and opted to try a closed-system CPU water cooling kit (Antec Kuhler H2O 620) that was on sale for a very good price over the Thanksgiving weekend. Most of my components are still in transit, but I became somewhat worried when a friend mentioned that abandoning air cooling units can result in heat buildup inside the case due to heat generated by the video card and other components such as RAM, the northbridge, MOSFETs and voltage regulators radiating heat that the CPU fan would normally at least keep circulating around so it doesn't build up in localized areas. Is this a realistic problem? What other precautions should I take to remove heat from other components? Adding more case fans seems like it would get really noisy. Are there quiet alternatives?

  Read the article

< Previous Page | 51 52 53 54 55 56 57 58 59 60 61 62  | Next Page >