Search Results

Search found 2343 results on 94 pages for 'masterchris 99'.

Page 55/94 | < Previous Page | 51 52 53 54 55 56 57 58 59 60 61 62  | Next Page >

• Basic IP address structure

  - by dannymcc

  We currently have a few servers, around 30-40 workstations and 16 phones. Each device has a static IP address. As an example the standard settings for a new workstation is; IP: 192.168.1.XXX Subnet: 255.255.255.0 Gateway: 192.168.1.99 DNS: 192.168.1.50 As I am slowly exploring new server OS's and virtualisation etc. I am getting close to wanting a wider range of IP addresses. What I would like to do is seperate the devices by IP as follows: Servers 192.168.1.XXX Workstations 192.168.2.XXX Printers 192.168.3.XXX Phones 192.168.4.XXX VM's 192.168.5.XXX Is this a bad idea, or is this a common way of doing things? My biggest concern is the phones and subnet masks. The phones are managed by our provider although I have access to the server that runs them. Would I need to change the subnet mask to 255.255.0.0 on all devices? Or only those that change? For example, the phones don't need to connect to any other devices other than other phones and the phone server. So if I have the phones on 192.168.1.XXX with a subnet mask of 255.255.255.0 and then moved everything I had complete ownership/control of to 192.168.X.XXX with a new subnet mask of 255.255.0.0. Would that work?

  Read the article

• HA for Resque & Redis

  - by Chris Go

  Trying to avoid SPOFs for Resque and Redis. Ultimately the client is going to be PHP via (https://github.com/chrisboulton/php-resque). After going through and finding some workable HA for nginx+php-fpm and MySQL (mysql master-master setup as a way to simply master-slave promotion), next up is Resque+Redis. Standard install of Resque uses localhost Redis (at DigitalOcean). I am heavily depending on Amazon Route 53 DNS failover to try to solve this. resque1.domain.com points to localhost redis (redis1.domain.com) = same server resque2.domain.com points to localhost redis (redis2.domain.com) = same server Do resque.domain.com with FAILOVER resque1 as primary and resque2 as secondary. What this means is that most of the time (99%), resque1 should be getting hit with resque2 as just a hot backup. This lets me just have to get 2 servers and makes sure that any hits to resque.domain.com goes somewhere The other way to do this is to break out resque and redis into 4 servers and do it as follows resque1.domain.com - redis.domain.com resque2.domain.com - redis.domain.com redis1.domain.com redis2.domain.com Then setup DNS Failover resque.domain.com - primary: resque1 and secondary: resque2 redis.domain.com - primary: redis1 and secondary: redis2 I'd like to get away for 2 servers if I can but is this 2nd setup much better or negligible? Thanks, Chris

  Read the article

• What used the linux memory? Low cache, low buffer, not a VM

  - by Jason

  First of all, yes, I have read LinuxAteMyRAM, which doesn't explain my situation. # free -tm total used free shared buffers cached Mem: 48149 43948 4200 0 4 75 -/+ buffers/cache: 43868 4280 Swap: 38287 0 38287 Total: 86436 43948 42488 # As shown above, the -/+ buffers/cache: line shows indicates the used memory rate is very high. However, from output of top, I don't see any process used more than 100MB of memory. So, what used the memory? PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 28078 root 18 0 327m 92m 10m S 0 0.2 0:25.06 java 31416 root 16 0 250m 28m 20m S 0 0.1 25:54.59 ResourceMonitor 21598 root -98 0 26552 25m 8316 S 0 0.1 80:49.54 had 24580 root 16 0 24152 10m 760 S 0 0.0 1:25.87 rsyncd 4956 root 16 0 62588 10m 3132 S 0 0.0 12:36.54 vxconfigd 26703 root 16 0 139m 7120 2900 S 1 0.0 4359:39 hrmonitor 21873 root 15 0 18764 4684 2152 S 0 0.0 30:07.56 MountAgent 21883 root 15 0 13736 4280 2172 S 0 0.0 25:25.09 SybaseAgent 21878 root 15 0 18548 4172 2000 S 0 0.0 52:33.46 NICAgent 21887 root 15 0 12660 4056 2168 S 0 0.0 25:07.80 SybaseBkAgent 17798 root 25 0 10652 4048 1160 S 0 0.0 0:00.04 vxconfigbackupd This is an x86_64 machine (not a common-brand server) running x84_64 Linux, not a container in a virtual machine. Kernel (uname -a): Linux 2.6.16.60-0.99.1-smp #1 SMP Fri Oct 12 14:24:23 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux Content of /proc/meminfo: MemTotal: 49304856 kB MemFree: 4066708 kB Buffers: 35688 kB Cached: 132588 kB SwapCached: 0 kB Active: 26536644 kB Inactive: 17296272 kB HighTotal: 0 kB HighFree: 0 kB LowTotal: 49304856 kB LowFree: 4066708 kB SwapTotal: 39206624 kB SwapFree: 39206528 kB Dirty: 200 kB Writeback: 0 kB AnonPages: 249592 kB Mapped: 52712 kB Slab: 1049464 kB CommitLimit: 63859052 kB Committed_AS: 659384 kB PageTables: 3412 kB VmallocTotal: 34359738367 kB VmallocUsed: 478420 kB VmallocChunk: 34359259695 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 Hugepagesize: 2048 kB df reports no large consumption of memory from tmpfs filesystems.

  Read the article

• How to test email spam scores with amavis?

  - by CaptSaltyJack

  I'd like a way to test a spam message to see its spam scores that SpamAssassin gives it. The SA db files (bayes_toks, etc) reside in /var/lib/amavis/.spamassassin. I've been testing emails by doing this: sudo su amavis -c 'spamassassin -t msgfile' Though this yields some strange results, such as: Content analysis details: (3.7 points, 5.0 required) pts rule name description ---- ---------------------- -------------------------------------------------- 3.5 BAYES_99 BODY: Bayes spam probability is 99 to 100% [score: 1.0000] -0.0 NO_RELAYS Informational: message was not relayed via SMTP 0.0 LONG_TERM_PRICE BODY: LONG_TERM_PRICE 0.2 BAYES_999 BODY: Bayes spam probability is 99.9 to 100% [score: 1.0000] -0.0 NO_RECEIVED Informational: message has no Received headers 0.2 is an awfully low scores for BAYES_999! But this is the first time I've used amavis, previously I've always just used spamassassin directly as a content filter in postfix, but apparently running amavis/spamassassin is more efficient. So, with amavis in the picture, how can I run a test on a message to see its spam score breakdown? Another email I ran a test on got this result: 2.0 BAYES_80 BODY: Bayes spam probability is 80 to 95% [score: 0.8487] Doesn't make sense, that BAYES_80 can yield a higher score than BAYES_999. Help!

  Read the article

• Server 2008 R2 DNS Lockup / Stops Resolving Internet Names

  - by Richard Maynard

  We've deployed our first 2008 R2 server on a client site which has replaced their existing 2003 DC. This server provides DNS resolution services to all client machines on that site for general internet usage. Since using the 2008 R2 DNS services we have noticed every couple of days the DNS server starts timing out when requests to certain sites are made (google is the only example I can provide at this time although it seems to be larger sites with problems rather than small - CDN compatiblity issue?). When you restart the DNS Server service then resolution returns to normal... just only for a day or so. Is anybody aware of any significant changes to the DNS server architecture or configuration out of the box in R2 that may explain this intermittent behaviour? I have already tried the fix listed here to no avail: http://weblogs.asp.net/owscott/archive/2009/09/15/windows-server-2008-r2-dns-issues.aspx The following PS command prompt info illustrates the issue: PS C:\Users\Administrator.UK> nslookup Default Server: s8209001.uk.kingdomfaith.com Address: 10.1.3.4 > www.google.com Server: s8209001.uk.kingdomfaith.com Address: 10.1.3.4 Non-authoritative answer: Name: www.l.google.com Addresses: 66.102.9.99 66.102.9.104 66.102.9.105 66.102.9.103 66.102.9.147 Aliases: www.google.com > www.google.co.uk Server: s8209001.uk.kingdomfaith.com Address: 10.1.3.4 * s8209001.uk.kingdomfaith.com can't find www.google.co.uk: Server failed

  Read the article

• LAN->LAN IP translation (for TortoiseSVN + Artifacts + Buffalo router)

  - by Armchair Bronco

  Here's my scenario: I've got a VisualSVN server on my main dev box @ home. I'm also using Visual Studio 2010, TortoiseSVN, VisualSVN client (for source control), and Versioned 'Artifacts' (for bug tracking). (I had to modify the fake URL's below to use only one slash because as a new user, I can't post more than one real URL.) I've got my Buffalo AirStation WHR-HP-G300N router properly configured so my business partner can connect to the SVN server. I have port forwarding enabled for the internet-side IP address (like http:/99.888.77.66:443) which gets forwarded to an internal IP (like 192.168.11.6). This part is working great. The problem I'm having is with the integration piece between TortoiseSVN and my bug tracking system. I need to provide a bugtraq:url property, but I haven't been able to get relative paths to work. So I'm forced to use an absolute URL. On my end, I need to use the name of my server (for example: bugtraq:url = https:/my-server/svn/bla..), but this doesn't work for my partner. He needs to specify the IP address (for example: bugtraq:url = https:/999.888.77.66:443/svn/bla...) Is there a way to configure my router such that the IP address for this parameter gets re-routed/re-mapped to "https://my-server" if the request originates from the LAN itself? My router's software supports LAN-Internet and Internet-LAN, but I don't see LAN-LAN.

  Read the article

• Moving automatically spam messages to a folder in Postfix

  - by cad

  Hi My problem is that I want to automatically to move spam messages to a folder and not sure how. I have a linux box giving email access. MTA is Postfix, IMAP is Courier. As webmail client I use Squirrelmail. To filter SPAM I use Spamassassin and is working ok. Spamassasin is overwriting subjects with [--- SPAM 14.3 ---] Viagra... Also is adding headers: X-Spam-Flag: YES X-Spam-Checker-Version: SpamAssassin 3.2.5 (2008-06-10) on xxxx X-Spam-Level: ************** X-Spam-Status: Yes, score=14.3 required=2.0 tests=BAYES_99, DATE_IN_FUTURE_24_48,HTML_MESSAGE,MIME_HTML_ONLY,RCVD_IN_PBL, RCVD_IN_SORBS_WEB,RCVD_IN_XBL,RDNS_NONE,URIBL_RED,URIBL_SBL autolearn=no version=3.2.5 X-Spam-Report: * 0.0 URIBL_RED Contains an URL listed in the URIBL redlist * [URIs: myimg.de] * 3.5 BAYES_99 BODY: Bayesian spam probability is 99 to 100% * [score: 1.0000] * 0.9 RCVD_IN_PBL RBL: Received via a relay in Spamhaus PBL * [113.170.131.234 listed in zen.spamhaus.org] * 3.0 RCVD_IN_XBL RBL: Received via a relay in Spamhaus XBL * 0.6 RCVD_IN_SORBS_WEB RBL: SORBS: sender is a abuseable web server * [113.170.131.234 listed in dnsbl.sorbs.net] * 3.2 DATE_IN_FUTURE_24_48 Date: is 24 to 48 hours after Received: date * 0.0 HTML_MESSAGE BODY: HTML included in message * 1.5 MIME_HTML_ONLY BODY: Message only has text/html MIME parts * 1.5 URIBL_SBL Contains an URL listed in the SBL blocklist * [URIs: myimg.de] * 0.1 RDNS_NONE Delivered to trusted network by a host with no rDNS I want to automatically to move spam messages to a folder. Ideally (not sure if possible) only to move messages with puntuation 5.0 or more to folder.. spam between 2.0 and 5.0 I want to be stored in Inbox. (I plan later to switch autolearn on) After reading a lot in procmail, postfix and spamassasin sites and googling a lot (lot of outdated howtos) I found two solutions but not sure which is the best or if there is another one: Put a rule in squirrelmail (dirty solution?) Use Procmail Which is the best option? Do you have any updated howto about it? Thanks

  Read the article

• How do you verify a restore?

  - by Nic

  What tool(s) would you use to verify that a restored file structure is whole and complete? My environment is a Windows Server 2008 file server. (We use tape for backup, but that is inconsequential.) I am specifically looking for a tool that will: Record the names of all files and folders below a specified directory Optionally calculate checksums of each file encountered Save this index in a human-readable format Compare the index against restored data and show differences Some background: I recently had to replace the disks in our file server. The upgrade was scheduled to start 36 hours after the most recent full backup, so I created a differential backup. However, it turns out that one of our applications was clearing the archive bit on files saved to the server, so these were not included in the differential backup. I was unaware of this until my users reported some files as missing. Aside from this, are there any other common methods for validating the integrity of a restore? I am frequently told that testing backups by restoring them is the only way to know that backups are working, but how do you deal with the case where it works 99% correctly and the other 1% silently fails?

  Read the article

• Is Windows Server 2008R2 NAP solution for NAC (endpoint security) valuable enough to be worth the hassles?

  - by Warren P

  I'm learning about Windows Server 2008 R2's NAP features. I understand what network access control (NAC) is and what role NAP plays in that, but I would like to know what limitations and problems it has, that people wish they knew before they rolled it out. Secondly, I'd like to know if anyone has had success rolling it out in a mid-size (multi-city corporate network with around 15 servers, 200 desktops) environment with most (99%) Windows XP SP3 and newer Windows clients (Vista, and Win7). Did it work with your anti-virus? (I'm guessing NAP works well with the big name anti-virus products, but we're using Trend micro.). Let's assume that the servers are all Windows Server 2008 R2. Our VPNs are cisco stuff, and have their own NAC features. Has NAP actually benefitted your organization, and was it wise to roll it out, or is it yet another in the long list of things that Windows Server 2008 R2 does, but that if you do move your servers up to it, you're probably not going to want to use. In what particular ways might the built-in NAP solution be the best one, and in what particular ways might no solution at all (the status quo pre-NAP) or a third-party endpoint security or NAC solution be considered a better fit? I found an article where a panel of security experts in 2007 say NAC is maybe "not worth it". Are things better now in 2010 with Win Server 2008 R2?

  Read the article

• MS SQL to MySQL using MySQL Migration Toolkit: permission issue

  - by Zeno

  I have a MS SQL imported into SQL Server 2008 from a .bak and I set it to Mixed mode. I have a SQL user (called "test") that can correctly access the database using SQL Server. I need to convert this to a MySQL database, so I got the MySQL Migration Toolkit. I pick "MS SQL Server" and then it asks for the hostname/username/password/database. I'm not 100% sure on these, but I used "localhost" (running on same computer), left the port as is (1433) and the username/password ("test") for the SQL Server. And I used the database name for the SQL Server database I'm looking to import. I clicked next, enter my MySQL database details and then attempt to run it and I get this error: Connecting to source database and retrieve schemata names. Initializing JDBC driver ... Driver class MS SQL JDBC Driver Opening connection ... Connection jdbc:jtds:sqlserver://localhost:1433/Orders;user=test;password=blah;charset=utf-8;domain= The list of schema names could not be retrieved (error: 0). ReverseEngineeringMssql.getSchemata :Network error IOException: Connection refused: connect Details: net.sourceforge.jtds.jdbc.ConnectionJDBC2.<init>(ConnectionJDBC2.java:372) net.sourceforge.jtds.jdbc.ConnectionJDBC3.<init>(ConnectionJDBC3.java:50) net.sourceforge.jtds.jdbc.Driver.connect(Driver.java:178) java.sql.DriverManager.getConnection(Unknown Source) java.sql.DriverManager.getConnection(Unknown Source) com.mysql.grt.modules.ReverseEngineeringGeneric.establishConnection(ReverseEngineeringGeneric.java:141) com.mysql.grt.modules.ReverseEngineeringMssql.getSchemata(ReverseEngineeringMssql.java:99) sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) sun.reflect.NativeMethodAccessorImpl.invoke(Unknown Source) sun.reflect.DelegatingMethodAccessorImpl.invoke(Unknown Source) java.lang.reflect.Method.invoke(Unknown Source) com.mysql.grt.Grt.callModuleFunction(Unknown Source)

  Read the article

• Best CPUs for speeding up compiling times of C++ w/ DistGCC

  - by Jay

  I'm putting together a distributed build farm with DistGCC to speed up our teams compile times and just looking for thoughts on which processors to use in the hosts. Are we going to get a noticeable decrease in time using 8 cores vs. 4-hyperthreaded cores? Big difference in time between i7 and Xeon? etc, etc. Just need advice from people who've put together kick-a build clusters. We've got a majority of the normal things to speed up builds in place (pre-compiled headers, ccache, local gigabit connections between them, tons of ram, etc) so please just give advice on the best processor to use. And money is a factor, but anythings doable if the performance increase is noticeable. Thanks. Jay EDIT: Although any advice IS welcome, please refrain from "Do this first" posts as we're not planning on skimping on things like SSD, maxed out RAM, etc. My personal system is a iMac Quad-core i5 with 8GB of RAM. When I build our project locally, my processor floats around 99-100% a majority of the time, which makes me assume it is a bottleneck, even if you made everything else faster. My ram on the other hand doesn't even get close to maxing out. It's also worth noting that I did research this, however every discussion I could find was primarily for gaming machines, which is obviously a different beast in usage. These machines won't even have monitors or anything but integrated graphics since they have one purpose: Build freakin fast. (hopefully)

  Read the article

• Best CPUs for speeding up compiling times of C++ w/ DistGCC

  - by Jay

  I'm putting together a distributed build farm with DistGCC to speed up our teams compile times and just looking for thoughts on which processors to use in the hosts. Are we going to get a noticeable decrease in time using 8 cores vs. 4-hyperthreaded cores? Big difference in time between i7 and Xeon? etc, etc. Just need advice from people who've put together kick-a build clusters. We've got a majority of the normal things to speed up builds in place (pre-compiled headers, ccache, local gigabit connections between them, tons of ram, etc) so please just give advice on the best processor to use. And money is a factor, but anythings doable if the performance increase is noticeable. Thanks. Jay EDIT: Although any advice IS welcome, please refrain from "Do this first" posts as we're not planning on skimping on things like SSD, maxed out RAM, etc. My personal system is a iMac Quad-core i5 with 8GB of RAM. When I build our project locally, my processor floats around 99-100% a majority of the time, which makes me assume it is a bottleneck, even if you made everything else faster. My ram on the other hand doesn't even get close to maxing out. It's also worth noting that I did research this, however every discussion I could find was primarily for gaming machines, which is obviously a different beast in usage. These machines won't even have monitors or anything but integrated graphics since they have one purpose: Build freakin fast. (hopefully)

  Read the article

• Best CPUs for speeding up compiling times of C++ w/ DistGCC

  - by Jay

  I'm putting together a distributed build farm with DistGCC to speed up our teams compile times and just looking for thoughts on which processors to use in the hosts. Are we going to get a noticeable decrease in time using 8 cores vs. 4-hyperthreaded cores? Big difference in time between i7 and Xeon? etc, etc. Just need advice from people who've put together kick-a build clusters. We've got a majority of the normal things to speed up builds in place (pre-compiled headers, ccache, local gigabit connections between them, tons of ram, etc) so please just give advice on the best processor to use. And money is a factor, but anythings doable if the performance increase is noticeable. Thanks. Jay EDIT: Although any advice IS welcome, please refrain from "Do this first" posts as we're not planning on skimping on things like SSD, maxed out RAM, etc. My personal system is a iMac Quad-core i5 with 8GB of RAM. When I build our project locally, my processor floats around 99-100% a majority of the time, which makes me assume it is a bottleneck, even if you made everything else faster. My ram on the other hand doesn't even get close to maxing out. It's also worth noting that I did research this, however every discussion I could find was primarily for gaming machines, which is obviously a different beast in usage. These machines won't even have monitors or anything but integrated graphics since they have one purpose: Build freakin fast. (hopefully)

  Read the article

• High Load mysql on Debian server stops every day. Why?

  - by Oleg Abrazhaev

  I have Debian server with 32 gb memory. And there is apache2, memcached and nginx on this server. Memory load always on maximum. Only 500m free. Most memory leak do MySql. Apache only 70 clients configured, other services small memory usage. When mysql use all memory it stops. And nothing works, need mysql reboot. Mysql configured use maximum 24 gb memory. I have hight weight InnoDB bases. (400000 rows, 30 gb). And on server multithread daemon, that makes many inserts in this tables, thats why InnoDB. There is my mysql config. [mysqld] # # * Basic Settings # default-time-zone = "+04:00" user = mysql pid-file = /var/run/mysqld/mysqld.pid socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /var/lib/mysql tmpdir = /tmp language = /usr/share/mysql/english skip-external-locking default-time-zone='Europe/Moscow' # # Instead of skip-networking the default is now to listen only on # localhost which is more compatible and is not less secure. # # * Fine Tuning # #low_priority_updates = 1 concurrent_insert = ALWAYS wait_timeout = 600 interactive_timeout = 600 #normal key_buffer_size = 2024M #key_buffer_size = 1512M #70% hot cache key_cache_division_limit= 70 #16-32 max_allowed_packet = 32M #1-16M thread_stack = 8M #40-50 thread_cache_size = 50 #orderby groupby sort sort_buffer_size = 64M #same myisam_sort_buffer_size = 400M #temp table creates when group_by tmp_table_size = 3000M #tables in memory max_heap_table_size = 3000M #on disk open_files_limit = 10000 table_cache = 10000 join_buffer_size = 5M # This replaces the startup script and checks MyISAM tables if needed # the first time they are touched myisam-recover = BACKUP #myisam_use_mmap = 1 max_connections = 200 thread_concurrency = 8 # # * Query Cache Configuration # #more ignored query_cache_limit = 50M query_cache_size = 210M #on query cache query_cache_type = 1 # # * Logging and Replication # # Both location gets rotated by the cronjob. # Be aware that this log type is a performance killer. #log = /var/log/mysql/mysql.log # # Error logging goes to syslog. This is a Debian improvement :) # # Here you can see queries with especially long duration log_slow_queries = /var/log/mysql/mysql-slow.log long_query_time = 1 log-queries-not-using-indexes # # The following can be used as easy to replay backup logs or for replication. # note: if you are setting up a replication slave, see README.Debian about # other settings you may need to change. #server-id = 1 #log_bin = /var/log/mysql/mysql-bin.log server-id = 1 log-bin = /var/lib/mysql/mysql-bin #replicate-do-db = gate log-bin-index = /var/lib/mysql/mysql-bin.index log-error = /var/lib/mysql/mysql-bin.err relay-log = /var/lib/mysql/relay-bin relay-log-info-file = /var/lib/mysql/relay-bin.info relay-log-index = /var/lib/mysql/relay-bin.index binlog_do_db = 24avia expire_logs_days = 10 max_binlog_size = 100M read_buffer_size = 4024288 innodb_buffer_pool_size = 5000M innodb_flush_log_at_trx_commit = 2 innodb_thread_concurrency = 8 table_definition_cache = 2000 group_concat_max_len = 16M #binlog_do_db = gate #binlog_ignore_db = include_database_name # # * BerkeleyDB # # Using BerkeleyDB is now discouraged as its support will cease in 5.1.12. #skip-bdb # # * InnoDB # # InnoDB is enabled by default with a 10MB datafile in /var/lib/mysql/. # Read the manual for more InnoDB related options. There are many! # You might want to disable InnoDB to shrink the mysqld process by circa 100MB. #skip-innodb # # * Security Features # # Read the manual, too, if you want chroot! # chroot = /var/lib/mysql/ # # For generating SSL certificates I recommend the OpenSSL GUI "tinyca". # # ssl-ca=/etc/mysql/cacert.pem # ssl-cert=/etc/mysql/server-cert.pem # ssl-key=/etc/mysql/server-key.pem [mysqldump] quick quote-names max_allowed_packet = 500M [mysql] #no-auto-rehash # faster start of mysql but no tab completition [isamchk] key_buffer = 32M key_buffer_size = 512M # # * NDB Cluster # # See /usr/share/doc/mysql-server-*/README.Debian for more information. # # The following configuration is read by the NDB Data Nodes (ndbd processes) # not from the NDB Management Nodes (ndb_mgmd processes). # # [MYSQL_CLUSTER] # ndb-connectstring=127.0.0.1 # # * IMPORTANT: Additional settings that can override those from this file! # The files must end with '.cnf', otherwise they'll be ignored. # !includedir /etc/mysql/conf.d/ Please, help me make it stable. Memory used /etc/mysql # free total used free shared buffers cached Mem: 32930800 32766424 164376 0 139208 23829196 -/+ buffers/cache: 8798020 24132780 Swap: 33553328 44660 33508668 Maybe my problem not in memory, but MySQL stops every day. As you can see, cache memory free 24 gb. Thank to Michael Hampton? for correction. Load overage on server 3.5. Maybe hdd or another problem? Maybe my config not optimal for 30gb InnoDB ? I'm already try mysqltuner and tunung-primer.sh , but they marked all green. Mysqltuner output mysqltuner >> MySQLTuner 1.0.1 - Major Hayden <[email protected]> >> Bug reports, feature requests, and downloads at http://mysqltuner.com/ >> Run with '--help' for additional options and output filtering -------- General Statistics -------------------------------------------------- [--] Skipped version check for MySQLTuner script [OK] Currently running supported MySQL version 5.5.24-9-log [OK] Operating on 64-bit architecture -------- Storage Engine Statistics ------------------------------------------- [--] Status: -Archive -BDB -Federated +InnoDB -ISAM -NDBCluster [--] Data in MyISAM tables: 112G (Tables: 1528) [--] Data in InnoDB tables: 39G (Tables: 340) [--] Data in PERFORMANCE_SCHEMA tables: 0B (Tables: 17) [!!] Total fragmented tables: 344 -------- Performance Metrics ------------------------------------------------- [--] Up for: 8h 18m 33s (14M q [478.333 qps], 259K conn, TX: 9B, RX: 5B) [--] Reads / Writes: 84% / 16% [--] Total buffers: 10.5G global + 81.1M per thread (200 max threads) [OK] Maximum possible memory usage: 26.3G (83% of installed RAM) [OK] Slow queries: 1% (259K/14M) [!!] Highest connection usage: 100% (201/200) [OK] Key buffer size / total MyISAM indexes: 1.5G/5.6G [OK] Key buffer hit rate: 100.0% (6B cached / 1M reads) [OK] Query cache efficiency: 74.3% (8M cached / 11M selects) [OK] Query cache prunes per day: 0 [OK] Sorts requiring temporary tables: 0% (0 temp sorts / 247K sorts) [!!] Joins performed without indexes: 106025 [!!] Temporary tables created on disk: 49% (351K on disk / 715K total) [OK] Thread cache hit rate: 99% (249 created / 259K connections) [!!] Table cache hit rate: 15% (2K open / 13K opened) [OK] Open file limit used: 15% (3K/20K) [OK] Table locks acquired immediately: 99% (4M immediate / 4M locks) [!!] InnoDB data size / buffer pool: 39.4G/5.9G -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance MySQL started within last 24 hours - recommendations may be inaccurate Reduce or eliminate persistent connections to reduce connection usage Adjust your join queries to always utilize indexes Temporary table size is already large - reduce result set size Reduce your SELECT DISTINCT queries without LIMIT clauses Increase table_cache gradually to avoid file descriptor limits Variables to adjust: max_connections (> 200) wait_timeout (< 600) interactive_timeout (< 600) join_buffer_size (> 5.0M, or always use indexes with joins) table_cache (> 10000) innodb_buffer_pool_size (>= 39G) Mysql primer output -- MYSQL PERFORMANCE TUNING PRIMER -- - By: Matthew Montgomery - MySQL Version 5.5.24-9-log x86_64 Uptime = 0 days 8 hrs 20 min 50 sec Avg. qps = 478 Total Questions = 14369568 Threads Connected = 16 Warning: Server has not been running for at least 48hrs. It may not be safe to use these recommendations To find out more information on how each of these runtime variables effects performance visit: http://dev.mysql.com/doc/refman/5.5/en/server-system-variables.html Visit http://www.mysql.com/products/enterprise/advisors.html for info about MySQL's Enterprise Monitoring and Advisory Service SLOW QUERIES The slow query log is enabled. Current long_query_time = 1.000000 sec. You have 260626 out of 14369701 that take longer than 1.000000 sec. to complete Your long_query_time seems to be fine BINARY UPDATE LOG The binary update log is enabled Binlog sync is not enabled, you could loose binlog records during a server crash WORKER THREADS Current thread_cache_size = 50 Current threads_cached = 45 Current threads_per_sec = 0 Historic threads_per_sec = 0 Your thread_cache_size is fine MAX CONNECTIONS Current max_connections = 200 Current threads_connected = 11 Historic max_used_connections = 201 The number of used connections is 100% of the configured maximum. You should raise max_connections INNODB STATUS Current InnoDB index space = 214 M Current InnoDB data space = 39.40 G Current InnoDB buffer pool free = 0 % Current innodb_buffer_pool_size = 5.85 G Depending on how much space your innodb indexes take up it may be safe to increase this value to up to 2 / 3 of total system memory MEMORY USAGE Max Memory Ever Allocated : 23.46 G Configured Max Per-thread Buffers : 15.84 G Configured Max Global Buffers : 7.54 G Configured Max Memory Limit : 23.39 G Physical Memory : 31.40 G Max memory limit seem to be within acceptable norms KEY BUFFER Current MyISAM index space = 5.61 G Current key_buffer_size = 1.47 G Key cache miss rate is 1 : 5578 Key buffer free ratio = 77 % Your key_buffer_size seems to be fine QUERY CACHE Query cache is enabled Current query_cache_size = 200 M Current query_cache_used = 101 M Current query_cache_limit = 50 M Current Query cache Memory fill ratio = 50.59 % Current query_cache_min_res_unit = 4 K MySQL won't cache query results that are larger than query_cache_limit in size SORT OPERATIONS Current sort_buffer_size = 64 M Current read_rnd_buffer_size = 256 K Sort buffer seems to be fine JOINS Current join_buffer_size = 5.00 M You have had 106606 queries where a join could not use an index properly You have had 8 joins without keys that check for key usage after each row join_buffer_size >= 4 M This is not advised You should enable "log-queries-not-using-indexes" Then look for non indexed joins in the slow query log. OPEN FILES LIMIT Current open_files_limit = 20210 files The open_files_limit should typically be set to at least 2x-3x that of table_cache if you have heavy MyISAM usage. Your open_files_limit value seems to be fine TABLE CACHE Current table_open_cache = 10000 tables Current table_definition_cache = 2000 tables You have a total of 1910 tables You have 2151 open tables. The table_cache value seems to be fine TEMP TABLES Current max_heap_table_size = 2.92 G Current tmp_table_size = 2.92 G Of 366426 temp tables, 49% were created on disk Perhaps you should increase your tmp_table_size and/or max_heap_table_size to reduce the number of disk-based temporary tables Note! BLOB and TEXT columns are not allow in memory tables. If you are using these columns raising these values might not impact your ratio of on disk temp tables. TABLE SCANS Current read_buffer_size = 3 M Current table scan ratio = 2846 : 1 read_buffer_size seems to be fine TABLE LOCKING Current Lock Wait ratio = 1 : 185 You may benefit from selective use of InnoDB. If you have long running SELECT's against MyISAM tables and perform frequent updates consider setting 'low_priority_updates=1'

  Read the article

• Running Jackd on Ubuntu for my External Firewire Sound card

  - by Asaf

  Hello, I'm running Ubuntu 10.04 and I have an external Sound card: Phonic Firefly 302. I've connected the device, installed Jackd, added the lines: @audio - rtprio 99 @audio - memlock 500000 @audio - nice -10 to /etc/security/limits.conf logged out, logged back in, ran qjackctl (sudo qjackctl to be exact), ran the settings and chose "firewire" on the driver option, pressed "Start" and that was the output: 20:10:19.450 Patchbay deactivated. 20:10:19.578 Statistics reset. 20:10:19.601 ALSA connection graph change. 20:10:19.828 ALSA connection change. 20:10:21.293 Startup script... 20:10:21.293 artsshell -q terminate sh: artsshell: not found 20:10:21.695 Startup script terminated with exit status=32512. 20:10:21.695 JACK is starting... 20:10:21.695 /usr/bin/jackd -dfirewire -r44100 -p1024 -n3 jackd 0.118.0 Copyright 2001-2009 Paul Davis, Stephane Letz, Jack O'Quinn, Torben Hohn and others. jackd comes with ABSOLUTELY NO WARRANTY This is free software, and you are welcome to redistribute it under certain conditions; see the file COPYING for details 20:10:21.704 JACK was started with PID=22176. no message buffer overruns JACK compiled with System V SHM support. loading driver .. libffado 2.0.0 built Mar 31 2010 14:47:42 firewire ERR: Error creating FFADO streaming device cannot load driver module firewire no message buffer overruns 20:10:21.819 JACK was stopped successfully. 20:10:21.819 Post-shutdown script... 20:10:21.822 killall jackd jackd: no process found 20:10:22.230 Post-shutdown script terminated with exit status=256. 20:10:23.865 Could not connect to JACK server as client. - Overall operation failed. - Unable to connect to server. Please check the messages window for more info. Error: "/tmp/kde-asaf" is owned by uid 1000 instead of uid 0.

  Read the article

• What could cause a huge packet loss in Ubuntu 9.10, for both wired and wireless?

  - by xzenox

  I was previously using 9.04 fine (and in fact, I am posting this from my old 9.04 live cd). I tested the following install steps in a virtualbox vm prior to following the sames ones to upgrade my laptop: Download/burn ubuntu minimal cd (12mb one) Install ubuntu minimal sudo apt-get update sudo apt-get upgrade sudo apt-get ubuntu-desktop ubuntu-standard In the VM worked fine and I found myself with a working 9.10 ubuntu, network worked fine and I was able to test my backups and DropBox without a hitch (host was 9.04). When I followed the same steps on my laptop, everything worked up to after 9.10 being installed and working. As far as I can tell, everything besides eth0/wireless works. For some reason, I am unable to access the internet. Ping reports that over 99% of packets get lost (over an hour or so of pinging). This means for example that if I try hard enough, I can load a webpage but only at the cost of much patience... This happens both for a wired and wireless connection to my wrt310n (updated with latest firmware). At first I thought that it could be related to the ipv6 issues ppl have been experiencing however even after disabling ipv6 at the kernel level (through grub), I still get the issue. I do not think this is related to DNS issues or the likes since even when I ping my ISP's gateway IP, I have the same amount of packet loss. No DNS resolving should be required there. Access to my router works peachy with no packet loss there. I've tried different MTU values but to no avail. Note that this issue affects every web-enabled application: firefox, ping, synaptic, etc. The same hardware/router combo works with 9.04 but not with 9.10. In fact, when I did: sudo apt-get ubuntu-desktop ubuntu-standard after 9.10 minimal was installed, it downloaded over 400mb of packages without a hitch so my guess is that one of those packages either in ubuntu-desktop or ubuntu-standard is causing havok. Thoughts?

  Read the article

• squid will not listen on specific IP

  - by Chris

  I have a public subnet with squid installed. Let's say my subnet is from 1.2.3.2 to 1.2.4.254. When I set the following: http_port 50000 http_port 1.2.3.2:50000 it is working. But when I set: http_port 1.2.4.37:50000 it is not working. It is only working with my first public IP from my subnet. The error I get when it is not working is the following: commBind: Cannot bind socket FD 10 to 1.2.4.37:50000: (99) Cannot assign requested address What is wrong with my configuration? @Zoredache I have a dedicated server and the whole subnet is defined as IP Range. When I use only the port or the first IP and doing netstat -ntlp | grep 46555 I get the following: tcp 0 0 0.0.0.0:50000 0.0.0.0:* LISTEN 25532/(squid ) When I use my specific IP, then the netstat query will show nothing, as the server does not start. I don't want squid to listen on all or the first IP, it is just a specific one it should listen to.

  Read the article

• Which internet scenario would be better?

  - by JL

  I currently have an 8mbps (down) / 512kbps (up) telephone ADSL solution. I must say the reliability is excellent, and up until now its been the fastest connection I could get because I don't live in a cable zone. The real speed of my connection is around 7mbps, but sometimes I manage to get the full 8mbps. I use my connection for work, so it needs to be at least 99% reliable. Recently I was told by a guy who lives up the road that he has a wireless connection with an external antenna and his speeds are 20mbps / 512kbps - he's also paying about 1/2 of what I pay for my wired telephone connection. My question is, is wireless internet good enough for a power user who uses his connection for work 8 hours a day, including VPNing into servers remotely. Besides this I also enjoy playing the odd network game, not a WoW freak, but sometimes I do pick up the odd MMORPG and at times do indulge in some semi heavy gaming sprees. Will this wireless latency drive me crazy and seem slow in comparison? Will it be reliable enough, I also live in an area that snows heavily in winter. I guess its a question of - should I go wireless or not. I've only had 1 wireless connection before and that was years ago using iBurst technology and I remember it was terrible for VPN, but I guess the technology might have been improved since then? What do you guys think?

  Read the article

• Apache2 random 403 error & info server busy logs on Ubuntu

  - by risyasin

  Hello, I have a strange situation with apache2. Meanless, random 403 errors. Any page (html, php etc.) normally working. but if i request repeatedly by pressing refresh button of browser. it interrupts & sends a 403 randomly. after a few seconds it works again. in the error log, i see client denied by server configuration. main error log of apache says [info] server seems busy, (you may need to increase StartServers, or Min/MaxSpareServers), spawning 8 children, there are 99 idle, and 137 total children my current values IfModule mpm_prefork_module StartServers 120 MinSpareServers 100 MaxSpareServers 200 MaxClients 256 MaxRequestsPerChild 500 /IfModule i've increased 10 by 10. from 20. but nothing solved. i've disabled KeepAlive. What may cause this problem ? thank you in advance. a fresh install Ubuntu server x86 8.04.4 Virtualmin from it's website (not from debian repositories). Linux 2.6.24-27-server #1 SMP i686 - Apache 2.2.8 Mpm prefork Virtualmin version 3.78.gpl GPL PHP Version 5.2.4-2ubuntu5.10 Loaded modules: core_module (static) log_config_module (static) logio_module (static) mpm_prefork_module (static) http_module (static) so_module (static) actions_module shared) alias_module (shared) auth_basic_module (shared) auth_digest_module (shared) uthn_file_module (shared) authz_default_module (shared) authz_groupfile_module (shared) uthz_host_module (shared) authz_user_module (shared) autoindex_module (shared) ache_module shared) cgi_module (shared) deflate_module (shared) dir_module (shared) env_module (shared) expires_module (shared) fcgid_module (shared) file_cache_module (shared) eaders_module (shared) mime_module (shared) mime_magic_module (shared) evasive20_module shared) negotiation_module (shared) php5_module (shared) rewrite_module (shared) etenvif_module (shared) ssl_module (shared) status_module (shared) Syntax OK

  Read the article

• Google.com always forward me to google.com.hk

  - by Ta Coen

  Any one could help me to figure out why Google.com always forward me to google.com.hk? $ dig google.com www.google.com. 509426 IN CNAME www.l.google.com. www.l.google.com. 100 IN A 74.125.71.147 www.l.google.com. 100 IN A 74.125.71.99 www.l.google.com. 100 IN A 74.125.71.105 www.l.google.com. 100 IN A 74.125.71.106 www.l.google.com. 100 IN A 74.125.71.104 www.l.google.com. 100 IN A 74.125.71.103 and $ dig google.com.hk www.google.com.hk. 261572 IN CNAME www.google.com. www.google.com. 589217 IN CNAME www.l.google.com. www.l.google.com. 139 IN A 74.125.235.17 www.l.google.com. 139 IN A 74.125.235.18 www.l.google.com. 139 IN A 74.125.235.19 www.l.google.com. 139 IN A 74.125.235.20 www.l.google.com. 139 IN A 74.125.235.16 How to make my network always goes to google.com?

  Read the article

• Postfix Whitelist before recipient restrictions

  - by GruffTech

  Alright. Some background. We have an anti-spam cluster trucking about 2-3 million emails per day, blocking somewhere in the range of 99% of spam email from our end users. The underlying SMTP server is Postfix 2.2.10. The "Frontline defense" before mail gets carted off to SpamAssassin/ClamAV/ ect ect, is attached below. ...basic config.... smtpd_recipient_restrictions = reject_unauth_destination, reject_rbl_client b.barracudacentral.org, reject_rbl_client cbl.abuseat.org, reject_rbl_client bl.mailspike.net, check_policy_service unix:postgrey/socket ...more basic config.... As you can see, standard RBL services from various companies, as well as a Postgrey service. The problem is, I have one client (out of thousands) who is very upset that we blocked an important email of theirs. It was sent through a russian freemailer who was currently blocked in two of our three RBL servers. I explained the situation to them, however they are insisting we do not block any of their emails. So i need a method of whitelisting ANY email that comes to domain.com, however i need it to take place before any of the recipient restrictions, they want no RBL or postgrey blocking at all. I've done a bit of research myself, http://www.howtoforge.com/how-to-whitelist-hosts-ip-addresses-in-postfix seemed to be a good guide at first, almost fixing my problem, But i want it to accept based on TO address, not originating server.

  Read the article

• Huge host CPU usage in idle vmware guest. Ubuntu 10.04 host, Vista SP2 guest

  - by themesandmodules

  I'm experiencing huge host CPU usage with an idle vmware guest. Host: Ubuntu 10.04 32-bit 2.6.32-24-generic-pae. (Very new install, i.e 24 hours ago) Hardware is Dell XPS M1530 laptop, 4GB ram. Intel Core II Duo T9300 2.50Ghz The virtualization setting "VT" or something is enabled in my bios. Guest: Completely fresh install of Windows Vista, upgraded to latest SP2 and all windows updates installed. 1024 - 1512MB ram allocated. Absolutely no other software installed on it, apart from VMWare tools. Situation When the guest is doing absolutely nothing, I watch with sysinternals process watch on the guest. This shows that system idle process is between 70 and 99%, usually around 95%. No actual process doing anything. On the host, I watch with top, I get cpu usage of 20% - 80%, usually around 30%. What I have tried Single and Dual processor available to guest - no change. Turn off all peripherals to guest - no network, drives, usb etc - no change. Turn off 3d acceleration for guest - perhaps a small improvement, or no change. Upping allocated ram to guest from 1024MB to 1512MB - no change. Yelling at vmware - no change. I have experienced a similar issue in the past, which was solved by setting the guest to have 1 CPU. This time that hasn't worked.

  Read the article

• Assets not served - Apache Reverse proxy - Diaspora

  - by Matt

  I have succeeded in installing Diaspora* on my subdomain diaspora.mattaydin.com. I have VPS running CentOS 5.7 with Plesk installed. By means of an vhost.conf and vhost_ssl.conf file I, (with the help of another gentleman) have managed to reverse proxy the app. vhost.conf: ServerName diaspora.mattaydin.com ServerAlias *.diaspora.mattaydin.com <Directory /home/diaspora/diaspora/public> Options -Includes -ExecCGI </Directory> DocumentRoot /home/diaspora/diaspora/public RedirectPermanent / https://diaspora.mattaydin.com vhost_ssl.conf ServerName diaspora.mattaydin.com DocumentRoot /home/diaspora/diaspora/public RewriteEngine On RewriteCond %{DOCUMENT_ROOT}/%{REQUEST_FILENAME} !-f RewriteRule ^/(.*)$ balancer://upstream%{REQUEST_URI} [P,QSA,L] <Proxy balancer://upstream> BalancerMember http://127.0.0.1:3000/ </Proxy> ProxyRequests Off ProxyVia On ProxyPreserveHost On RequestHeader set X_FORWARDED_PROTO https <Proxy *> Order allow,deny Allow from all </Proxy> <Directory /home/diaspora/diaspora/public> Options -Includes -ExecCGI Allow from all AllowOverride all Options +Indexes </Directory> DocumentRoot /home/diaspora/diaspora/public Basically it's working. However, the only thing that's not working are the assets. The do not get loaded not the server, as seen on diaspora.mattaydin.com The error messages I get in the access_ssl.log are a lot of: 11/Dec/2012:19:04:05 +0100] "GET /robots.txt HTTP/1.1" 404 2811 "-" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_8_2) AppleWebKit/536.26.17 (KHTML, like Gecko) Version/6.0.2 Safari/536.26.17" The error messages I get from diaspora's log file is: Started GET "//assets/branding/logo_large.png" for 77.250.99.193 at 2012-12-11 20:13:11 +0100 ActionController::RoutingError (No route matches [GET] "/assets/branding/logo_large.png"): lib/rack/chrome_frame.rb:39:in call' lib/unicorn_killer.rb:35:incall' Hope you guys can help me out. If you need anything else please let me know Thanks in advance, Matt

  Read the article

• SSH login very slow on OS X Leopard

  - by acjohnson55

  My SSH sessions take a very long time to initiate. This applies for logins with and without passwords, interactive and non-interactive. I have tried setting 'GSSAPIAuthentication no' and 'IPQoS 0x00' on the client side, and 'UseDNS no' on the server side, but no dice. I'm really stumped and frustrated. The worst part is that it SFTP takes forever to establish connections too, making file transfer much longer than it would be otherwise. I thought the problem might be something with PAM, because of where the hang is in the sshd log below, so I tried commenting out each line one-by-one in the /etc/pam.d/sshd file. Some caused login to be impossible, some had no apparent effect. I can't really tell if PAM is stalling for other services, but I can say that su'ing into my account from another account with 'su -l' has no apparent delay. I tried creating a new user account, just to see if there was something wrong with my existing account, and the same problem persisted. Any ideas of what's going on? On the client side, the most verbose mode outputs (redacted where reasonable): OpenSSH_5.9p1, OpenSSL 0.9.8r 8 Feb 2011 debug1: Reading configuration data ... debug1: ... line 1: Applying options for ... debug1: Reading configuration data /etc/ssh_config debug1: /etc/ssh_config line 20: Applying options for * debug1: /etc/ssh_config line 53: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to ... [x.x.x.x] port 22. debug1: Connection established. debug1: identity file /.../.ssh/id_rsa type -1 debug1: identity file /.../.ssh/id_rsa-cert type -1 debug3: Incorrect RSA1 identifier debug3: Could not load "/.../.ssh/id_dsa" as a RSA1 public key debug1: identity file /.../.ssh/id_dsa type 2 debug1: identity file /.../.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.2 debug1: match: OpenSSH_5.2 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.9 debug2: fd 3 setting O_NONBLOCK debug3: load_hostkeys: loading entries for host "..." from file "/.../.ssh/known_hosts" debug3: load_hostkeys: found key type RSA in file /.../.ssh/known_hosts:9 debug3: load_hostkeys: loaded 1 keys debug3: order_hostkeyalgs: prefer hostkeyalgs: [email protected],[email protected],ssh-rsa debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: [email protected],[email protected],ssh-rsa,[email protected],[email protected],ssh-dss debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-sha2-256,hmac-sha2-256-96,hmac-sha2-512,hmac-sha2-512-96,hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-sha2-256,hmac-sha2-256-96,hmac-sha2-512,hmac-sha2-512-96,hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: ssh-rsa,ssh-dss debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: mac_setup: found hmac-md5 debug1: kex: server->client aes128-ctr hmac-md5 none debug2: mac_setup: found hmac-md5 debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug2: dh_gen_key: priv key bits set: 136/256 debug2: bits set: 523/1024 debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA ... debug3: load_hostkeys: loading entries for host "..." from file "/.../.ssh/known_hosts" debug3: load_hostkeys: found key type RSA in file /.../.ssh/known_hosts:9 debug3: load_hostkeys: loaded 1 keys debug3: load_hostkeys: loading entries for host "x.x.x.x" from file "/.../.ssh/known_hosts" debug3: load_hostkeys: found key type RSA in file /.../.ssh/known_hosts:9 debug3: load_hostkeys: loaded 1 keys debug1: Host '...' is known and matches the RSA host key. debug1: Found key in /.../.ssh/known_hosts:9 debug2: bits set: 492/1024 debug1: ssh_rsa_verify: signature correct debug2: kex_derive_keys debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /.../.ssh/id_dsa (0x7f8b7b41d6c0) debug2: key: /.../.ssh/id_rsa (0x0) debug1: Authentications that can continue: publickey,password,keyboard-interactive debug3: start over, passed a different list publickey,password,keyboard-interactive debug3: preferred publickey,keyboard-interactive,password debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive,password debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Offering DSA public key: /.../.ssh/id_dsa debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug1: Server accepts key: pkalg ssh-dss blen 434 debug2: input_userauth_pk_ok: fp ... debug3: sign_and_send_pubkey: DSA ... debug1: Authentication succeeded (publickey). Authenticated to ... ([x.x.x.x]:22). debug1: channel 0: new [client-session] debug3: ssh_session2_open: channel_new: 0 debug2: channel 0: send open debug1: Requesting [email protected] debug1: Entering interactive session. ****** Hangs here ****** debug2: callback start debug2: client_session2_setup: id 0 debug2: fd 3 setting TCP_NODELAY debug2: channel 0: request pty-req confirm 1 debug1: Sending environment. debug3: Ignored env TERM_PROGRAM debug3: Ignored env SHELL debug3: Ignored env TERM debug3: Ignored env TMPDIR debug3: Ignored env Apple_PubSub_Socket_Render debug3: Ignored env TERM_PROGRAM_VERSION debug3: Ignored env TERM_SESSION_ID debug3: Ignored env USER debug3: Ignored env COMMAND_MODE debug3: Ignored env SSH_AUTH_SOCK debug3: Ignored env Apple_Ubiquity_Message debug3: Ignored env __CF_USER_TEXT_ENCODING debug3: Ignored env PATH debug3: Ignored env MKL_NUM_THREADS debug3: Ignored env PWD debug1: Sending env LANG = en_US.UTF-8 debug2: channel 0: request env confirm 0 debug3: Ignored env HOME debug3: Ignored env SHLVL debug3: Ignored env DYLD_LIBRARY_PATH debug3: Ignored env PYTHONPATH debug3: Ignored env LOGNAME debug3: Ignored env DISPLAY debug3: Ignored env SECURITYSESSIONID debug3: Ignored env _ debug2: channel 0: request shell confirm 1 debug2: callback done debug2: channel 0: open confirm rwindow 0 rmax 32768 debug2: channel_input_status_confirm: type 99 id 0 debug2: PTY allocation request accepted on channel 0 debug2: channel 0: rcvd adjust 2097152 debug2: channel_input_status_confirm: type 99 id 0 debug2: shell request accepted on channel 0 On the server side, the debug output looks like: Sep 16 18:46:40 ... sshd[31435]: debug1: inetd sockets after dupping: 3, 4 Sep 16 18:46:40 ... sshd[31435]: Connection from x.x.x.x port 52758 Sep 16 18:46:40 ... sshd[31435]: debug1: Current Session ID is 56AC0FB0 / Session Attributes are 00008000 Sep 16 18:46:40 ... sshd[31435]: debug1: Running in inetd mode in a non-root session... assuming inetd created the session for us. Sep 16 18:46:40 ... sshd[31435]: debug1: Client protocol version 2.0; client software version OpenSSH_5.9 Sep 16 18:46:40 ... sshd[31435]: debug1: match: OpenSSH_5.9 pat OpenSSH* Sep 16 18:46:40 ... sshd[31435]: debug1: Enabling compatibility mode for protocol 2.0 Sep 16 18:46:40 ... sshd[31435]: debug1: Local version string SSH-2.0-OpenSSH_5.2 Sep 16 18:46:40 ... sshd[31435]: debug1: Checking with Service ACLs for ssh login restrictions Sep 16 18:46:40 ... sshd[31435]: debug1: call to mbr_user_name_to_uuid with <...> suceeded to retrieve user_uuid Sep 16 18:46:40 ... sshd[31435]: debug1: Call to mbr_check_service_membership failed with status <0> Sep 16 18:46:40 ... sshd[31435]: debug1: PAM: initializing for "..." Sep 16 18:46:40 ... sshd[31435]: debug1: PAM: setting PAM_RHOST to "x.x.x.x" Sep 16 18:46:40 ... sshd[31435]: Failed none for ... from x.x.x.x port 52758 ssh2 Sep 16 18:46:40 ... sshd[31435]: debug1: temporarily_use_uid: 509/20 (e=0/0) Sep 16 18:46:40 ... sshd[31435]: debug1: trying public key file /.../.ssh/authorized_keys Sep 16 18:46:40 ... sshd[31435]: debug1: restore_uid: 0/0 Sep 16 18:46:40 ... sshd[31435]: debug1: temporarily_use_uid: 509/20 (e=0/0) Sep 16 18:46:40 ... sshd[31435]: debug1: trying public key file /.../.ssh/authorized_keys2 Sep 16 18:46:40 ... sshd[31435]: debug1: fd 5 clearing O_NONBLOCK Sep 16 18:46:40 ... sshd[31435]: debug1: matching key found: file /.../.ssh/authorized_keys2, line 1 Sep 16 18:46:40 ... sshd[31435]: Found matching DSA key: ... Sep 16 18:46:40 ... sshd[31435]: debug1: restore_uid: 0/0 Sep 16 18:46:40 ... sshd[31435]: debug1: temporarily_use_uid: 509/20 (e=0/0) Sep 16 18:46:40 ... sshd[31435]: debug1: trying public key file /.../.ssh/authorized_keys Sep 16 18:46:40 ... sshd[31435]: debug1: restore_uid: 0/0 Sep 16 18:46:40 ... sshd[31435]: debug1: temporarily_use_uid: 509/20 (e=0/0) Sep 16 18:46:40 ... sshd[31435]: debug1: trying public key file /.../.ssh/authorized_keys2 Sep 16 18:46:40 ... sshd[31435]: debug1: fd 5 clearing O_NONBLOCK Sep 16 18:46:40 ... sshd[31435]: debug1: matching key found: file /.../.ssh/authorized_keys2, line 1 Sep 16 18:46:40 ... sshd[31435]: Found matching DSA key: ... Sep 16 18:46:40 ... sshd[31435]: debug1: restore_uid: 0/0 Sep 16 18:46:40 ... sshd[31435]: debug1: ssh_dss_verify: signature correct Sep 16 18:46:40 ... sshd[31435]: debug1: do_pam_account: called Sep 16 18:46:40 ... sshd[31435]: Accepted publickey for ... from x.x.x.x port 52758 ssh2 Sep 16 18:46:40 ... sshd[31435]: debug1: monitor_child_preauth: ... has been authenticated by privileged process Sep 16 18:46:40 ... sshd[31435]: debug1: PAM: establishing credentials ***** Hangs here ***** Sep 16 18:46:54 ... sshd[31435]: User child is on pid 31654 Sep 16 18:46:54 ... sshd[31654]: debug1: PAM: establishing credentials Sep 16 18:46:54 ... sshd[31654]: debug1: permanently_set_uid: 509/20 Sep 16 18:46:54 ... sshd[31654]: debug1: Entering interactive session for SSH2. Sep 16 18:46:54 ... sshd[31654]: debug1: server_init_dispatch_20 Sep 16 18:46:54 ... sshd[31654]: debug1: server_input_channel_open: ctype session rchan 0 win 1048576 max 16384 Sep 16 18:46:54 ... sshd[31654]: debug1: input_session_request Sep 16 18:46:54 ... sshd[31654]: debug1: channel 0: new [server-session] Sep 16 18:46:54 ... sshd[31654]: debug1: session_new: session 0 Sep 16 18:46:54 ... sshd[31654]: debug1: session_open: channel 0 Sep 16 18:46:54 ... sshd[31654]: debug1: session_open: session 0: link with channel 0 Sep 16 18:46:54 ... sshd[31654]: debug1: server_input_channel_open: confirm session Sep 16 18:46:54 ... sshd[31654]: debug1: server_input_global_request: rtype [email protected] want_reply 0 Sep 16 18:46:54 ... sshd[31654]: debug1: server_input_channel_req: channel 0 request pty-req reply 1 Sep 16 18:46:54 ... sshd[31654]: debug1: session_by_channel: session 0 channel 0 Sep 16 18:46:54 ... sshd[31654]: debug1: session_input_channel_req: session 0 req pty-req Sep 16 18:46:54 ... sshd[31654]: debug1: Allocating pty. Sep 16 18:46:54 ... sshd[31435]: debug1: session_new: session 0 Sep 16 18:46:54 ... sshd[31654]: debug1: session_pty_req: session 0 alloc /dev/ttys008 Sep 16 18:46:54 ... sshd[31654]: debug1: server_input_channel_req: channel 0 request env reply 0 Sep 16 18:46:54 ... sshd[31654]: debug1: session_by_channel: session 0 channel 0 Sep 16 18:46:54 ... sshd[31654]: debug1: session_input_channel_req: session 0 req env Sep 16 18:46:54 ... sshd[31654]: debug1: server_input_channel_req: channel 0 request shell reply 1 Sep 16 18:46:54 ... sshd[31654]: debug1: session_by_channel: session 0 channel 0 Sep 16 18:46:54 ... sshd[31654]: debug1: session_input_channel_req: session 0 req shell Sep 16 18:46:54 ... sshd[31655]: debug1: Setting controlling tty using TIOCSCTTY.

  Read the article

• Where is my CPU usage going?

  - by Josh

  My Ubuntu 10.04 Lucid virtual machine is saying it's at 100% CPU usage... but all I'm running is Thunderbird. According to top, CPU usage should be ~25.9%... How do I interpret this conflicting output from top? top - 13:55:26 up 3:35, 4 users, load average: 3.03, 2.59, 2.48 Tasks: 178 total, 1 running, 177 sleeping, 0 stopped, 0 zombie Cpu(s): 16.0%us, 79.7%sy, 0.0%ni, 0.0%id, 0.0%wa, 1.3%hi, 3.0%si, 0.0%st Mem: 509364k total, 479108k used, 30256k free, 3092k buffers Swap: 2096440k total, 58380k used, 2038060k free, 225116k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 7708 jnet 20 0 480m 109m 17m S 18.4 22.1 21:59.14 thunderbird-bin 4615 jnet 20 0 5488 1268 1040 S 2.3 0.2 5:00.03 nx-rootless-ses 7124 jnet 20 0 56688 27m 4812 S 2.0 5.5 6:35.09 nxagent 6724 nx 20 0 9628 1400 636 S 1.6 0.3 3:26.59 sshd 30106 root 20 0 2544 1236 908 R 0.7 0.2 0:00.33 top 19 root 20 0 0 0 0 S 0.3 0.0 0:22.45 ata/0 38 root 20 0 0 0 0 S 0.3 0.0 0:05.53 scsi_eh_1 345 root 20 0 0 0 0 S 0.3 0.0 0:04.72 kjournald 1719 root 20 0 3260 1192 944 S 0.3 0.2 0:17.36 vmware-guestd 1 root 20 0 2804 1356 940 S 0.0 0.3 0:01.99 init 2 root 20 0 0 0 0 S 0.0 0.0 0:00.01 kthreadd 3 root RT 0 0 0 0 S 0.0 0.0 0:00.00 migration/0 4 root 20 0 0 0 0 S 0.0 0.0 0:00.15 ksoftirqd/0 5 root RT 0 0 0 0 S 0.0 0.0 0:00.00 watchdog/0 ... Specifically I'm referring to the fact that the CPU usage totals show 0% idle time: Cpu(s): 16.0%us, 79.7%sy, 0.0%ni, 0.0%id, 0.0%wa, 1.3%hi, 3.0%si, 0.0%st Yet when adding up the percentages in the %CPU column I get 25.9%, not 100%!

  Read the article

< Previous Page | 51 52 53 54 55 56 57 58 59 60 61 62  | Next Page >