Search Results

Search found 16351 results on 655 pages for 'metro screen'.

Page 550/655 | < Previous Page | 546 547 548 549 550 551 552 553 554 555 556 557  | Next Page >

• My Linux desktop sees my HDMI-connected monitor, but my monitor says "No signal"

  - by hrunting

  I have a Gigabyte H55M-UD2H motherboard and an Acer S271HL monitor. When I connect the monitor to the motherboard via VGA, signal works perfectly. When I connect the monitor via HDMI, the system "sees" the connection, but the monitor receives no signal (the monitor shows a blue box which reads "No Signal" and then the monitor goes into power-saving state). Some fun facts about this: if I hook a different monitor to this box via HDMI, the monitor receives the output without issue (same computer/motherboard, same cable, different monitor) if I connect a different computer to the monitor via HDMI, the monitor receives the output without issue (different computer, same cable, same monitor) no signal is received whether in the OS or in the BIOS there are no BIOS options for controlling video output other than for selection of onboard vs. PCI/PCI-E-based video card (the system has no dedicated video card installed) The box is running Linux, so I have the output of xrandr which shows the connection and the monitor modes detected via DDC: ~$ xrandr --prop Screen 0: minimum 320 x 200, current 1920 x 1080, maximum 8192 x 8192 VGA1 disconnected (normal left inverted right x axis y axis) HDMI1 disconnected (normal left inverted right x axis y axis) Broadcast RGB: Full supported: Full Limited 16:2 audio: auto supported: force-dvi off auto on DP1 disconnected (normal left inverted right x axis y axis) Broadcast RGB: Full supported: Full Limited 16:2 audio: auto supported: force-dvi off auto on HDMI2 connected 1920x1080+0+0 (normal left inverted right x axis y axis) 598mm x 336mm EDID: 00ffffffffffff000472ca028d128022 1c160103803c2278ca7b45a4554aa227 0b5054bfef80714f8140818081c08100 9500b300d1c0023a801871382d40582c 450056502100001e000000fd00384c1f 5311000a202020202020000000fc0053 323731484c0a202020202020000000ff 004c55573044303130383531300a01e5 020324f14f0102030405060790111213 1415161f230907078301000067030c00 1000382d023a801871382d40582c4500 56502100001f011d8018711c1620582c 250056502100009f011d007251d01e20 6e28550056502100001e8c0ad08a20e0 2d10103e960056502100001800000000 000000000000000000000000000000de Broadcast RGB: Full supported: Full Limited 16:2 audio: auto supported: force-dvi off auto on 1920x1080 60.0*+ 50.0 25.0 30.0 1680x1050 59.9 1680x945 60.0 1400x1050 74.9 59.9 1600x900 60.0 1280x1024 75.0 60.0 1440x900 75.0 59.9 1280x960 60.0 1366x768 60.0 1360x768 60.0 1280x800 74.9 59.9 1152x864 75.0 1280x768 74.9 60.0 1280x720 50.0 60.0 1440x576 25.0 1024x768 75.1 70.1 60.0 1440x480 30.0 1024x576 60.0 832x624 74.6 800x600 72.2 75.0 60.3 56.2 720x576 50.0 848x480 60.0 720x480 59.9 640x480 72.8 75.0 66.7 60.0 59.9 720x400 70.1 HDMI3 disconnected (normal left inverted right x axis y axis) Broadcast RGB: Full supported: Full Limited 16:2 audio: auto supported: force-dvi off auto on DP2 disconnected (normal left inverted right x axis y axis) Broadcast RGB: Full supported: Full Limited 16:2 audio: auto supported: force-dvi off auto on DP3 disconnected (normal left inverted right x axis y axis) Broadcast RGB: Full supported: Full Limited 16:2 audio: auto supported: force-dvi off auto on How do I get this monitor to recognize the output from this HDMI socket?

  Read the article

• How do I configure nVidia drivers on a Portable Ubuntu setup?

  - by Nicholas Flynt

  I've been pulling my hair out over this one for a couple of days now, google is no help. I've created a wonderful (until this issue) portable copy of Ubuntu linux that will boot on mostly anything by using a USB enclosure for my laptop's 80GB SATA drive. So far so good, it boots and runs on everything, and on non-nVidia card setups was even detecting the drivers, or letting me install the required drivers for hardware acceleration and compiz. Because you know, the wobble windows are the most awesome thing ever. Anyway, my desktop machine had an nVidia card, so I'm thinking, sure, I'll just install the nVidia drivers like before and everything will work happily. Not so-- now the desktop and any other nVidia cards work great, but it seems to have completely disabled any other graphics cards. When the kernel module detects that an nVidia card isn't present, it shoots up this nasty little dialog box giving me the option to boot into "low graphics" mode, which doesn't even allow me to use the correct screen resolution, much less see the installed graphics card and try to configure a driver for it. Is there any way to configure Ubuntu (with the dreaded nVidia kernel module) so that it can use nVidia's drivers when an nVidia card is present, and default to the normal (not low-graphics) setup in other cases, so that it has a fair chance of using what's actually present? I'm not afraid to much with config files, I just don't know the underlying system well enough to feel comfortable diving in without a push in the right direction. Thanks guys!

  Read the article

• Postfix 554 <[email protected]>: Relay access denied

  - by Matt

  So i am trying to set postfix up and I am running into some problems.....here is my files vim /etc/postfix/main.cf relayhost = [smtp.gmail.com]:587 smtp_connection_cache_destinations = smtp.gmail.com smtp_sasl_auth_enable=yes smtp_sasl_password_maps = hash:/etc/postfix/sasl_passwd smtp_sasl_tls_security_options = noanonymous tls_random_source = dev:/dev/urandom smtp_tls_CAfile= /etc/pki/CA/cacert.pem smtp_tls_security_level = may smtp_tls_scert_verifydepth = 9 append_dot_mydomain = no readme_directory = no myhostname = maggie.deliverypath.com alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = /etc/mailname mydestination = maggie.deliverypath.com, localhost.deliverypath.com, , localhost mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all I also have the gmail password info vim /etc/postfix/sasl_passwd gmail-smtp.l.google.com [email protected]:somepass smtp.gmail.com [email protected]:somepass then I try to follow this article and i get this output telnet mail.demoslice.com 25 Trying 67.207.128.80... Connected to www.slicehost.com. Escape character is '^]'. 220 www.slicehost.com ESMTP Postfix (Ubuntu) HELO test.demoslice.com 250 www.slicehost.com MAIL FROM:<[email protected]> 250 Ok RCPT TO:<[email protected]> 554 <[email protected]>: Relay access denied its started service postfix start * Starting Postfix Mail Transport Agent postfix ...done. then the screen gets frozen and i cant do anything....any ideas

  Read the article

• Resolving a BSOD/CPU/GPU issue...

  - by Christian Sciberras

  Hello all, I'm getting a BSOD / system crash (sometimes the PC just quits without a BSOD). Hardware Specifications cpu: i7 920 2666MHz / 8 cores (not OCed afaik) mobo: Asus P6T SE ram: 2x Corsair CM3X2G1333C9 (64bit DDR3 667MHz) gfx: ATI Radeon HD 5970 1GB (XFX HD5970 BE) os: Windows 7 Ultimate 64 bit (legit) All bios, firmware and drivers are all up to date (as of today). Symptoms Sometimes the PC runs smoothly, sometimes I get this BSOD. The BSOD always happens when I'm doing something related to graphics, such as viewing a video or playing a game. I get to know about the imminent BSOD ~10 seconds earlier; the PC starts freezing occasionally but increasing in frequency and length of lag (I noticed processor usage in creased from Process Monitor). I've tweaked BIOS settings occasionally but afaik, it was in vain. A day or so ago, I reset it to factory settings. BSOD contents The computer has rebooted from a bugcheck. The bugcheck was: 0x00000101 (0x0000000000000019, 0x0000000000000000, 0xfffff88001f35180, 0x0000000000000004). 15-12-2010 A fatal hardware error has occurred. Reported by component: Processor Core Error Source: Machine Check Exception Error Type: Internal Timer Error Processor ID: 4 23-12-2010 A fatal hardware error has occurred. Reported by component: Processor Core Error Source: Machine Check Exception Error Type: Internal Timer Error Processor ID: 2 Important The interesting thing is that although the event log (and BSOD screen) blame a "secondary processor", Windows Action Center sometimes blamed the GFX driver (for the same error). Also It is interesting to note that after hibernating my PC, I always get the BSOD.

  Read the article

• Windows 7 boot failure after update

  - by Jake

  Installed some windows 7 updates today, mostly just optional fixes and it installed an update to my IntelliType or IntelliPoint drivers (Keyboard & Mouse). It asked to reboot, computer gets to the windows load screen and redirects to the repair utility. Repair utility failed, it said if I recently installed a device, unplug it and try to restart. So I unplugged my keyboard and mouse, restarted. Nothing. I noticed that all the errors seemed to be Windows 7 thinking the installation was on another one of my slave drives. For example, my windows installation is on C:, but I have other drives, like G:, X:, etc... So it said "Critical Boot File G:\Windows\system32\drivers\amdxata.sys is corrupt, but why not C:\ ? So I unplugged ALL other hard drives, it still tried loading X:, even though the only one plugged in was C: I have the windows disk, but that didn't seem to help. I was thinking I need to fix my boot.ini or something simple like that was corrupt, the hard drives seem fine. I'm screwed, it's finals week.

  Read the article

• windows 8.1 does not boot after CHKDSK command

  - by sepehr

  I had problem with Windows 8.1 high Disk usage so in order to solve , searched forums. A voted answer suggested to use CHKDSK command as follow: run command prompt and as administrator type code snippet below: CHKDSK /f /v /b C: (I can not remember accurately) CHKDSK printed : can not run CHKDSK right now , would you like to schedule C drive to be checked next time windows starts? (Y/N) my response was "Y" ,please ! Following this suggestion not only didn't solve my problem as expected but also added another one ! The next time system booted, after windows authentication I just could see a black screen and mouse pointer. So I force shut downed the system and tried to start windows again. This time , windows got stuck in Scanning and Repairing on 22% for around 3 hours so I got tired and forced shut downed again. is CHKDSK source of Scanning and Repairing problem or they are discrete ? is there any hope to overcome this problem without re-installing windows ? can any one else run CHKDSK on newer versions of windows without problem? is CHKDSK effective but inefficient ?(it finally get to end but will take a long time) If yes, how much time does it take? I also have Linux Ubuntu 14.04 installed along side windows.

  Read the article

• How do you automatically close 3rd party applications when LiberKey is shut down?

  - by NoCatharsis

  Within LiberKey, I have added my own portable applications that are not included within the LiberKey library. When you go into the Properties menu for the app in the LiberKey UI, the Advanced tab has an option for Autoexecute. This dropdown menu seems to have no visible effect, at least on my current installation. I found that I could right click within the primary GUI and select "Add software group", add all 3rd party applications, then go to the Advanced tab within THAT Properties screen and select Autoexecute - "Always on startup". This solved the problem for starting the apps when LiberKey starts. However, now I'm having the same issue when closing out LiberKey. I have created a new 3rd party app that calls the same .exe, but sends the Parameter "/close". I then went to the Advanced tab and selected Autoexecute - "Always on shutdown". Seems pretty logical right? But the apps will not close on LiberKey shutdown. I cannot handle the app close-outs in the same way with a software group, as I did with the startup issue because the Autoexecute drop-down does not have an "Always on shutdown" option. Unfortunately, many of the Q&A forums on liberkey.com are in French and I took Spanish in high school. Otherwise I've not been able to find a workable answer. Any suggestions?

  Read the article

• i7 overclocking problem

  - by benwebdev

  Hi everyone, I've got an overclocked system that seems to be misbehaving. When trying to boot up from cold the system just hangs and nothing is output to the screen. Fans are on as they should but nothing happens to finish the boot. From here I have to switch it off then on again and the boot completes. If I go into the tweak menu in the BIOS I'm informed that a boot has failed I've been in touch with Overclockers UK support a bit and theres not yet been a solution. We've mainly been tweaking the voltage for the CPU. Any suggestions? I'm new to Overclocking which is why I got a bundle with OCUK. With this issue happening on Cold Boot too its tricky to test as I have to make a change then wait till the next day. My system is here: Intel Core i7 930 2.80Ghz overclocked to 4GHz Gigabyte X58A-UD3R (BIOS Version: FC) 6GB RAM Power Supply - CoolerMaster Silent Pro M series 700W One suggestion made by OCUK was that maybe its the power supply but I'm not sure and dont have a spare - it's brand new and a pretty expensive piece of kit. Any thoughts on this? Other recomendations for Power? thanks Ben

  Read the article

• Eclipse: Slow startup time

  - by ct2k7

  Hello, I've got Eclipse 3.6.1 on my MacBook Air (2010), and I'm getting slowish startup times. Well, slow, compared to my Desktop, which is somewhat less powerful and a few years old). The startup generally takes 15 seconds, and of this, 4 is spent just on the Eclipse splash screen, before Eclipse loads anything. No projects are open at startup. Here's a copy of my eclipse.ini. -startup ../../../plugins/org.eclipse.equinox.launcher_1.1.0.v20100507.jar --launcher.library ../../../plugins/org.eclipse.equinox.launcher.cocoa.macosx.x86_64_1.1.1.R36x_v20100810 -showsplash org.eclipse.platform --launcher.XXMaxPermSize 512m --launcher.defaultAction openFile -vmargs -Xms256m -Xmx512m -Xdock:icon=../Resources/Eclipse.icns -XstartOnFirstThread -Dorg.eclipse.swt.internal.carbon.smallFonts -Dosgi.requiredJavaVersion=1.6 -Xverify:none -XX:+UseConcMarkSweepGC -XX:+CMSClassUnloadingEnabled -XX:+CMSPermGenSweepingEnabled -XX:+UnlockExperimentalVMOptions -XX:+AggressiveOpts -XX:+StringCache -XX:+UseFastAccessorMethods -XX:+UseLargePages -XX:LargePageSizeInBytes=4m -XX:AllocatePrefetchLines=1 -XX:AllocatePrefetchStyle=1 -Dide.gc=true The problem doesn't seem to be related to plugins - I've disabled the ones which I don't need, and regardless of this configuration or whether all of them are selected on startup, it only takes 1second to load the plugins. I'm running Eclipse 3.6.1 Cocoa x64 build (vanilla) with the Zend Studio plugin. The machine has 4GB RAM, an SSD with over 64% free space, 1.6GHz (4MB L2 Cache). OS is Mac OS X 10.6.6, latest Java available, 1.6. For comparison, my Desktop, an old P4 3GHZ (512K L2 Cache) with a 7200RPM drive, under 40% free space, Eclipse (same config) loads in under 7 seconds, consistently. Note, this one is a Windows machine, with latest Java installed.

  Read the article

• Integrated Graphics went kaput, can I switch to dedicated graphics if I can't get into the BIOS

  - by Om Nom Nom

  I have an 8 year old computer (Pentium 4 1.6 GHz, 256 MB DDR RAM) which is not turning on (it beeps for 10 seconds and then goes off). Nothing appears on the screen, so I can't get into the BIOS. A computer repair person listened to the beeping pattern and told me that its because of the integrated graphics on the motherboard is defective. It's an ASUS P4S333-VM motherboard and the graphics solution is SiS 650. He tried putting in a PCI graphics card expecting that the computer will use that instead and ignore the integrated graphics, but apparently older computers don't switch automatically to the dedicated graphics card; it needs to be changed from the BIOS. But, I can't get inside the BIOS settings as I already said. I am told that the only option now is to replace the motherboard (which is not feasible since it's very old now). So, is there any way to make the computer use the PCI graphics card? IIRC, the motherboard also has an AGP port, but I think that it will also need to be selected from the BIOS?

  Read the article

• Windows 7 Not Starting and System Repair Not Loading

  - by Mark

  I have a Dell Inspiron 1545 running Windows 7 When turning on my PC I keep receiving a black screen with the option to use System Repair or Start Normally. Both options lead me to the System Repair background except no matter how long I wait the system restore options never show up. Choosing F8 and running all of the options including safe mode encounters the same result above. I tried to to use 2 system recovery disks 32x and 64x I downloaded and both lead to similiar results. When I choose System Repair running from the disk the System Repair Question asking to select a language pops ups but after this no matter how long I wait no other options appear. Next after restarting and selecting F8 (after hitting f12 and running from CD) I choose 'Run From Safe Mode with Command Prompt' I am able to run all of the options from System Restore with differing results: Startup Repair: Choosing this ends up in system repair indefinitely (left running 12 hrs) System Restore: Does Nothing. PC thinks for a second and then stops. When selecting ShutDown I see an error message stating there are no restore points. System Image Recovery: Service Cannot be started in Safe Mode Windows Memory Diagnostic: Runs test but then leads to system repair background which never loads system repair Command Prompt: chkdsk /r -Cannot Lock Current Drive...write protected. chkdsk /f -Cannot Lock Current Drive...write protected. bootcfg - Cannot open Boot.Ini file bootcfg - Ran all 3 (rebuildBcd, FixMbr and Fixboot) but PC still goes to System Repair background with no repair options popping up upon restart (without recovery CD). I'm on the verge of purchasing a boot utility disk for $50 unless there is anything else short of "take it to a computer shop" that somebody can suggest I try.

  Read the article

• Macbook Pro won't boot from DVD with SSD

  - by Adam Carr

  Here's the timeline of events. Had a running MBP 17 Early 2011 Thunderbolt with OWC Mercury Extreme Pro SSD 115GB drive. Installed Windows 7 via bootcamp. I have done this multiple times before and every time I need to format the bootcamp partition before installing. I think this time I actually deleted the partition and then selected the freespace to install. This worked fine for the most part but I wasn't able to boot the boot camp partition using vmware fusion. I gave up and used the boot camp assistant to revert back to one mac partition. I was getting some odd behavior so I rebooted the machine. It then came up with a message saying no bootable partiton. This made me think (and still does) that the windows install using the free space versus the boot camp partition caused the windows MBR boot loader to get installed incorrectly and mucked up the OS X installation. Ok, fine, I can just reinstall. I can't seem to boot from the original MBP installation DVD. I hold down c on boot but I never get past the all grey screen. I hear the DVD drive spin up but it eventually stops. I put the original HD back in it and everything works fine but when I put the SSD in, I can't boot from the DVD drive. I have already set up an RMA with OWC to send back the drive but considering the order of events, I feel as though it isn't a hardware issue but can't seem to figure out how to fix it. I can always send it back in but figured I would check and see if anyone could offer some guideance/assistence before doing so.

  Read the article

• How can I recover from SharePoint configuration errors after promoting the server to a Domain Controller?

  - by jjr2527

  I have a SharePoint 2010 VM setup in VirtualBox and I was using local machine accounts to handle security on the server. While preparing for a demo it came time to have some meaningful users on my VM image. I followed some docs on promoting my server to a Domain Controller in a new forrest. So now I have [MachineName].SPDEMO.CONTOSO.com and I can add users as needed. However, when I try to connect to my SharePoint sites I am getting a white screen with the error: "Cannot connect to the configuration database" I changed the pool identity account of each of my IIS app pools to the new Administrator account and started the services successfully but I can't get the SQL services to start up. When I try to start them I get the following error: Windows could not start the SQL Server (MSSQLSERVER) on Local Computer. For more information, review the System Event Log. If this is a non-Microsoft service, contact the service vendor, and refer to service-specific error code 17058. In the event log I see the following error: The SQL Server (MSSQLSERVER) service terminated with service-specific error %%17058. Can I recover from this or should I roll back or just uninstall the Domain Controller role. I'd like to keep the server as a standalone DC so I can do some user profile creation/management but I need the SharePoint bits to work as well.

  Read the article

• Apache / PHP Begins to Deny SQL Requests after about 2000

  - by Daniel Stern

  We have a web page on our server that we use to run administrative scripts. For example, we might run the script "unenrolStudents()" which runs 5,000 SQL SET commands one after another and sets 5000 student entries in an SQL database to unenrolled. However, we are finding that after running a few thousand queries (it is not totally consistent) we will be "locked out" by our server. SYMPTOMS OF LOCKING OUT: - unable to connect to server with winSCP - opening putty with that connection shows a blank screen (no login / pass) - clearing cookies / cache in chrome does NOT fix locking out - other computers in the office ALSO become locked out - locking out can be triggered with a high frequency of requests (10000 in 1 second) or by less over time (10000 in 500 seconds - this will still cause a lockout even though the frequency is much less) We believe this is a security feature of our own Apache. I know we are using Suhosin but I didn't configure it so I don't know. How can I disable this locking effect so that I can confidently run all my SQL requests and they will go through? Has anyone else dealt with this and found workarounds? Thanks DS

  Read the article

• How to set up TightVNC Java viewer index.html on web server?

  - by penyuan

  I've got the Java TightVNC viewer applet set up with the provided index.html on my Mac OS X 10.6.3 with web sharing enabled. Using a remote computer I was able to get to the webpage but I only see a white box with an X (for error?) that represents where the viewer is supposed to be. Any ideas on how to get this to work? I've tried to set the port (in index.html) to 5900 and 5901, none worked. Are any of these the default VNC port for Mac OS X 10.6.3? Also, I've activated Screen Sharing and Remote Login in System Preferences, allowing VNC viewers to connect. Here is the code for my index.html: <HTML> <TITLE> TightVNC desktop </TITLE> <APPLET CODE="classes/VncViewer.class" ARCHIVE="classes/VncViewer.jar" WIDTH="1440" HEIGHT="900"> <PARAM NAME="PORT" VALUE="5900"> <PARAM NAME="Scaling factor" VALUE="50"> </APPLET> <BR> <A href="http://www.tightvnc.com/">TightVNC site</A> </HTML> Again I can get to this page, but the applet doesn't seem to work, the Java console also doesn't say anything. Thanks in advance for your help!

  Read the article

• VNC failure on Xen

  - by BCable

  The following config works and creates a good VM in Xen: # Kernel Setup kernel = "/boot/vmlinuz-2.6.18.8-xenU" # Memory memory = "256" # Disk disk = [ "file:/opt/xen/domains/110/sda1.img,sda1,w", "file:/opt/xen/domains/110/swap.img,sda2,w" ] # container name name = "110" hostname = "boo" # Networking vif = ["type=ieomu, bridge=xenbr0"] # VNC vnc = 1 #vfb = [ 'type=vnc,vncdisplay=2,vnclisten=0.0.0.0,vncpasswd=110' ] # Behavior Settings root = "/dev/sda1" extra = "fastboot" But when I uncomment the VFB line, I get the following error after it hangs for at least 30 seconds: [root@customer 110]# xm create boo.cfg Using config file "./boo.cfg". Error: Device 0 (vkbd) could not be connected. Hotplug scripts not working. Any ideas? Part two of this question: Sometimes it actually works, and a port is opened. When this happens, nmap shows the VNC ports open and I can connect via the VNC client, but it just hangs at "Connection established." and no VNC display shows up. I've tried multiple VNC clients (TightVNC, TightVNC Java Console, RealVNC), but they all fail to connect. Does VNC through Xen require X to be started in order to function? I was under the impression that it would show the console screen, so I'm confused as to why all these issues are occurring. Thanks!

  Read the article

• Unable to communicate with EWS from Exchange Server

  - by kschieck

  We are currently running a 2 server exchange environment with Edge services on their own. We are in the process of trying to deploy a piece of software that uses the EWS API which has brought me to this form, the software ties into the EWS service and uses it to forward messages (this is failing). Using the software error logs I have found that accessing EWS from the exchange server is not possible. From my work machine and an external address I can type the following https ://webmail.companyname.com/ews/exchange.asmx and be prompted for a username and password, once I enter credentials I get a screen full of information from services.wsdl. The problem is when I try the same URL from the exchange server and get the credentials prompt I cannot get past it. Even with the same credentials that work externally and from my desk it just keeps looping around. Capture from software log (11:41:32.6415 000017e4 System.Net.WebException: The request failed with HTTP status 401: Unauthorized.) I have also found the same results when trying https://webmail.companyname.com/ Autodiscover /Autodiscover.xml . Environment Information Server 2008 STD 64bit Exchange 2007 SP1 Purchased Cert – webmail.companyname.com I have also confirmed that all services have the proper internal and external URL’s. Any help would be appreciated.

  Read the article

• 2000 Server, User can't logon

  - by Mike I

  I hope you can help me. I recently upgraded a workstation at my office (to a whole new machine) and ran into a pretty serious problem. Friday until 5:00 PM, I could access my mail on 2000 Exchange server. When I shut the old workstation down and put in the new workstation, I tried to set up an account. When I put the server name in appropriate field and typed my username and hit check names, my username does not come up. So to troubleshoot, (It also is a SMB server) I try to logon to my file share. (My local credentials are the same as server credientials of user account) When I try to logon to share, I just get the Username/Password screen (Never had gotten that before since credentials are the same) Again, in troubleshooting mode, I try to log on to my user from another workstation. Still can't authenticate via my user. Every other user can authenticate and load up their shares/mailboxes. I have restored Exchange from the backup as of 3 days ago (Thursday) but the exact same issue is still there. I really do not understand what is wrong and what else I can do to troubleshoot. If anyone has some pointers for me, I will surely accept them. Thanks, Mike

  Read the article

• Is there an high quality natural text reader for the mac?

  - by Another Registered User

  I'm reading about 150 pages of text on screen, every day. I will have to read about 15.000 in the next upcoming months. No joke. Well, the problem is this: I suffer from a sort of attention deficit hyperactivity disorder which forces me to read every sentence up to 10 times until I really get it. Mac OS X Snow Leopard has a built-in text reader with the name "Alex". Although it is already pretty good quality, I know there are far better natural sounding voices out there. I have heard already voices that are absolutely amazing compared to Alex. They're so good, that you can't tell anymore the difference between a real person or a computer. Alex still has this "metal factor" in its voice, which makes my ears hurt after 8 hours of listening. The next problem with Alex is, that he never makes a break after a sentence. Also, it's not possible to think about a sentence and then continue reading. It's also not possible to have him repeat a sentence, without tedious text selection and shortcut usage. Actually, the best tool I can imagine would have the option to read a sentence and move on to the next one after pressing a special key, OR repeating the previously one after pressing a special key. That would help so much! And if that's even with one of those bell lab / AT&T / whatever super-natural voices, even better! But it would be already a great relief if there was just a better tool to control Alex. To let him make breaks after sentences or let him speak big chunks of text sentence-by-sentence with fine-grained control over repetition and moving on. Is there anything?

  Read the article

• Acer LCD says "no signal"

  - by Ken

  I have an Acer 24" LCD (model "AL2423WDR") that's about 3 years old. It worked perfectly for most of its lifetime so far. Recently it started giving problems. When I turn it on, it either says "no signal" on the display, or the power light goes yellow (as if in power-saving mode). This happens with both DVI and VGA (both of which worked fine before), and stranger still, the 4 buttons on the front, for accessing the on-screen menus, don't do anything. I've also tried different computer hardware and software (PC/Mac, Linux/MacOS), but nothing has worked. I've tried power-cycling it (with both the power button and the power switch), and also unplugging it entirely. The nonworking buttons suggest to me an issue with the firmware. I found a place on Acer's website that says I can send it in to have it fixed, at my expense, but I'll avoid that if I can. Is there a way to fully reset it manually? Or is there something else I can try?

  Read the article

• Ubuntu Server mdadm drbd ocfs2 kvm hangs under heavy file reading

  - by Stefano Annese

  I have deployed four ubuntu 10.04 server. They are coupled two by two in a cluster scenario. on both sides we have software raid1 disks, drbd8 and OCFS2 and on top of it some kvm machines run with qcow2 disks. I followed this: Link corosync is just used for DRBD and OCFS, the kvm machines are run "manually" When it works is fine: good performances, good I/O, but at a given time one of the two cluster started hanging. Then we tried with just one server turned on and it hangs the same. It seems to happen when an heavy READ in one of the virtual machines occurs, that is during rsyn backup. When the fact occurs the virtual machines are not reachable any more and the real server responds with good delay to the ping but no screen and no ssh is available. All we can do is force shutdown (hold the button) and restart and when it turns on again the raid on which relay drbd is resyncing. All the time it hangs we see such fact. After a couple of week of pain on one side this morning also the other cluster hung, but it has different moteherboard, ram, kvm instances. What is similar is reading for rsync scenario and Western Digital RAID Edistion disks on both side. Can anybody give me some input to solve such issue?

  Read the article

• Media Center setup won't complete for watching TV

  - by Robert

  I have a problem watching TV in Media Center. The TV constantly pauses 1/2 second then plays 1 second, pauses 1/2 second, plays 1 second - it is constant and does not vary. This problem occurs on all channels, live or recorded. The bottom 5th of the screen is solid green. I know the problem is Media Center because I can use Pinnacle's TVCenterPro and there is no skipping/pausing (and not green on bottom). I was using cable, and switched to DirecTV (satellite). Trying to do "Set up TV signal" in Media Center seems to be what broke it. I get an error "IR Hardware not detected." I can use the remote to "try again" - so the IR hardware works fine (Media Center's remote/sensor). I tried plugging the IR Blaster into both ports, and I tried a different USB port for the IR receiver. I can't complete the setup. Media Center was playing it okay before I tried to run setup. (I ran setup to try to do recording with Media Center.) Pinnacle PCTV 800i HD PCI card (coax cable from DirecTV tuner), ATI Radeon HD 3200 Graphics, Windows XP SP3 Media Center Edition, AMD Athlon Dual Core 2.5 GHz, 1.75 GB RAM.

  Read the article

• pgpoolAdmin keeps going straight back to it's login page

  - by user705142

  I'm trying to run pgpoolAdmin through nginx - it seems to be working properly, at least initially. I've gone through the initial set-up, which works fine, but now after logging in every link takes me straight back to the login page. It also shows japanese text instead of english, despite picking english in the installation. It seems to me just as if it was unable to save any user data, session information etc. I have javascript/cookies enabled, so it's not that. The ownership of the folder is nginx, and so too is pgmgt.conf.php, so it shouldn't be a problem with permissions. One potential issue is that I can't seem to see any confirmation that php postgresql support is enabled in the php info screen, despite the correct package installed and in the config line. Any ideas as to what's happening here? The nginx rules are pretty standard: server { # pg-pool admin listen 997; server_name localhost; root /opt/pgpooladmin; index index.php; location ~ .php$ { fastcgi_pass_header Set-Cookie; fastcgi_pass 127.0.0.1:9000; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_param PATH_INFO $fastcgi_script_name; fastcgi_index index.php; include fastcgi_params; } }

  Read the article

• VNC on Xen failure

  - by BCable

  The following config works and creates a good VM in Xen: # Kernel Setup kernel = "/boot/vmlinuz-2.6.18.8-xenU" # Memory memory = "256" # Disk disk = [ "file:/opt/xen/domains/110/sda1.img,sda1,w", "file:/opt/xen/domains/110/swap.img,sda2,w" ] # container name name = "110" hostname = "boo" # Networking vif = ["type=ieomu, bridge=xenbr0"] # VNC vnc = 1 #vfb = [ 'type=vnc,vncdisplay=2,vnclisten=0.0.0.0,vncpasswd=110' ] # Behavior Settings root = "/dev/sda1" extra = "fastboot" But when I uncomment the VFB line, I get the following error after it hangs for at least 30 seconds: [root@customer 110]# xm create boo.cfg Using config file "./boo.cfg". Error: Device 0 (vkbd) could not be connected. Hotplug scripts not working. Any ideas? Part two of this question: Sometimes it actually works, and a port is opened. When this happens, nmap shows the VNC ports open and I can connect via the VNC client, but it just hangs at "Connection established." and no VNC display shows up. I've tried multiple VNC clients (TightVNC, TightVNC Java Console, RealVNC), but they all fail to connect. Does VNC through Xen require X to be started in order to function? I was under the impression that it would show the console screen, so I'm confused as to why all these issues are occurring. Thanks!

  Read the article

• NVidia Graphic Card troubleshooting

  - by Berry Langerak

  My dad has a HP pavilion laptop, which is over 6 years old. It contains an onboard graphic card, a NVidia GeForce 8400M GS. Since a week or two, he's getting BSOD in Windows Vista. Also, the screen was acting up; strange lines and figures keep creeping up, but only once in a while -- not always. Thinking that it might be the drivers he had recently upgraded, I decided to downgrade the driver, with no luck at all. I then continued to deinstall the driver, and reinstalling the current stable version, but alas, to no prevail. Windows kept crashing during the course of the last two weeks, and thinking it might be Windows breaking up, I decided to upgrade his Vista installation to Windows 7, as I've been hearing good things about it. Alas, even that didn't help, and it seems the strange lines and figures keep popping up. I've opened the laptop itself, thinking it might simply be overheating because of clogging in the vents, but that's not the case, it's clean as a whistle. Now for the actual question; does anyone have a decent flowchart on how to troubleshoot such issues? It might well be the videocard itself, as the strange lines and figures sometimes even appear during BIOS and POST, but I'm not sure.

  Read the article

< Previous Page | 546 547 548 549 550 551 552 553 554 555 556 557  | Next Page >