Search Results

Search found 15249 results on 610 pages for 'tv shows'.

Page 550/610 | < Previous Page | 546 547 548 549 550 551 552 553 554 555 556 557  | Next Page >

• Can only bring up one of two interfaces

  - by mstaessen

  I'm having a bizarre issue with my HP Proliant DL 360 G4p server. It has two gigabit ethernet interfaces but I can bring up only one of them. This is starting to freak me out and that's why I turned here. I'm running the x64 ubuntu 11.10 server edition. lshw -c network shows that the second interface is disabled. I have no idea why ans how to enable it. $ sudo lshw -c network *-network:0 description: Ethernet interface product: NetXtreme BCM5704 Gigabit Ethernet vendor: Broadcom Corporation physical id: 2 bus info: pci@0000:02:02.0 logical name: eth0 version: 10 serial: 00:18:71:e3:6d:26 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 66MHz capabilities: pcix pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 duplex=full firmware=5704-v3.27b, ASFIPMIc v2.36 ip=10.48.8.x latency=64 link=yes mingnt=64 multicast=yes port=twisted pair speed=100Mbit/s resources: irq:25 memory:fdf70000-fdf7ffff *-network:1 DISABLED description: Ethernet interface product: NetXtreme BCM5704 Gigabit Ethernet vendor: Broadcom Corporation physical id: 2.1 bus info: pci@0000:02:02.1 logical name: eth1 version: 10 serial: 00:18:71:e3:6d:25 capacity: 1Gbit/s width: 64 bits clock: 66MHz capabilities: pcix pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 firmware=5704-v3.27b latency=64 link=no mingnt=64 multicast=yes port=twisted pair resources: irq:26 memory:fdf60000-fdf6ffff If I try to ifup eth1, then I get $ sudo ifup eth1 Ignoring unknown interface eth1=eth1. I figured that's what happens when there is no eth1 listed in /etc/network/interfaces. But when I add the configuration for eth1, I still can't ifup. $ sudo ifup eth1 RTNETLINK answers: File exists Failed to bring up eth1. I've also tried ifconfig eth1 up but without any result. For clarity, I have added a masked version of /etc/network/interfaces. I don't think it is the cause of the problem though. $ cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 10.48.8.x netmask 255.255.255.y network 10.48.8.z broadcast 10.48.8.t gateway 10.48.8.u auto eth1 iface eth1 inet static address 193.190.253.x netmask 255.255.255.y network 193.190.253.z broadcast 193.190.253.t gateway 193.190.253.u I really need some help fixing this. It's driving me crazy. Thanks.

  Read the article

• Some Memory Slots Not Working on MSI FM2-A85XA-G65 Motherboard

  - by Mike Ciaraldi

  Short version of question: Does anyone have an MSI FM2-A85XA-G65 motherboard, who can confirm that all four memory slots work? Long version: Several months ago I bought an MSI FM2-A85XA-G65 motherboard at Newegg. At that point I installed an AMD A8-5500 processor and two sticks of Corsair Vengeance 8 GB DDR3-1866 memory, and put it into my file server. I installed the RAM in slots 1 and 3, as directed in the manual, to enable dual-channel memory access. It seemed to work fine, so I bought a second identical mobo (which arrived dead, but was quickly replaced by Newegg) and set of RAM, installed an A10-5800K, and put that into my production Linux machine. Again, it seemed to work well. Eventually I happened to notice that on the server only 8 GB of RAM appeared in the BIOS. I tried each of the slots and memory modules individually and in various combinations. I even swapped processors with the production machine. The result was that putting memory in slots 1 and 2 worked (showing a total of 16 GB), but any memory in slots 3 or 4 was not recognized. However, all four memory slots in the production machine worked, and I confirmed this with both processors. I contacted MSI and arranged to ship the defective mobo back to them for replacement under warranty. I did not want my file server to be down in the interim, and I had another machine I wanted to upgrade, so I bought a third identical mobo to use. That one had the same problem -- only memory slots 1 and 2 worked. I tested it thoroughly with multiple processors and memory sticks. I sent the defective mobo back to MSI and they sent me a new one. This has the same memory slot problem. So I sent it back. The replacement arrived the other day and shows the same problem. I contacted MSI yet again and they said that nobody else has reported memory slot problems on this board and it must be my processor. So my score so far is, out of six boards of this model, I have: One where all four slots work. One which was dead on arrival. Four where only memory slots 1 and 2 work. Before I tear my other machines apart and start swapping processors again I thought I would ask if anyone else has this exact model motherboard and could confirm that all four memory slots either do or do not work. According to MSI you should be able to just plug a single memory module into any of the slots and it will work (and it does on the one mobo I have which works correctly). If you have not yet used all four slots, this is a good time to test them so you know if you can expand your memory in the future. Thanks in advance to anyone who can help.

  Read the article

• Error in eclipse on run android project

  - by Larz

  I am trying to get a simple hello world android project working in eclipse using an android emulator. I have been using the examples on developer.android.com. I actually did have a hello world app working. I then modified it's xml files to have a text input field and a button as in the second example shows on that site. This failed to run on the emulator. I then went back and tried to create another simple hello world project, but it fails to run. The console says "Waiting for HOME ('android.process.acore') to be launched, but nothing happens or sometimes a messenger in the emulator says "unfortunately Android Wear has stopped". Below is a sample error filter on the log file. I find trying to debug this is something new to me and I am not sure the best way to go about it. I am just trying to learn some basic android developer skills. 05-30 16:19:07.336: E/SELinux(469): SELinux: Loaded file_contexts from /file_contexts, 05-30 16:19:07.336: E/SELinux(469): digest= 05-30 16:19:07.376: E/SELinux(469): b0 05-30 16:19:07.376: E/SELinux(469): 4b 05-30 16:19:07.756: E/SELinux(469): 03 05-30 16:19:07.756: E/SELinux(469): 4a 05-30 16:19:07.826: E/SELinux(469): 73 05-30 16:19:07.886: E/SELinux(469): ab 05-30 16:19:07.886: E/SELinux(469): 6d 05-30 16:19:07.896: E/SELinux(469): 46 05-30 16:19:07.896: E/SELinux(469): b4 05-30 16:19:07.896: E/SELinux(469): a5 05-30 16:19:07.896: E/SELinux(469): 73 05-30 16:19:07.896: E/SELinux(469): 8a 05-30 16:19:07.896: E/SELinux(469): ee 05-30 16:19:07.896: E/SELinux(469): ac 05-30 16:19:07.906: E/SELinux(469): 68 05-30 16:19:07.906: E/SELinux(469): ff 05-30 16:19:07.906: E/SELinux(469): 04 05-30 16:19:07.906: E/SELinux(469): dc 05-30 16:19:07.906: E/SELinux(469): b8 05-30 16:19:07.906: E/SELinux(469): a2 05-30 16:19:11.806: E/SensorManager(511): sensor or listener is null 05-30 16:19:16.196: E/BluetoothAdapter(378): Bluetooth binder is null 05-30 16:19:16.206: E/BluetoothAdapter(378): Bluetooth binder is null 05-30 16:19:17.186: E/WVMExtractor(54): Failed to open libwvm.so: dlopen failed: library "libwvm.so" not found 05-30 16:19:17.776: E/AudioCache(54): Error 1, -2147483648 occurred 05-30 16:19:17.796: E/SoundPool(378): Unable to load sample: (null) 05-30 16:19:18.536: E/AudioCache(54): Error 1, -2147483648 occurred 05-30 16:19:18.546: E/SoundPool(378): Unable to load sample: (null)

  Read the article

• SQL Transactional Replication snapshot not applying

  - by dmch2

  Hi, I'm using SQL Transactional Replication with pull subscriptions to replicate databases (hosting their own distribution database) from several servers across a VPN to a central server. I've got the first 2 databases working fine but the 3rd one is causing me problems. My subscription server is SQL 2008, the source systems are all SQL 2005. The source databases are a few 100Mb in size and contain audit data so are simply growing slowly by adding new records at approx 1kb a second. As far as the replication monitor, Agent logs and event logs show everything is working fine - except that no data appears in my subscription database. The distribution agent doesn't seem to want to read the snapshot (and hence the initial state and schema) from the publisher. New transactions aren't applied although they do seem to be arriving OK as the replication monitor shows things like '5 transactions with 10 commands were delivered'. I would expect (as in previous times) to see statements about data being BCPed in the replication monitor. The snapshot is on the publisher on a shared folder. The subscriber can view the snapshot OK (\\repldata) and the alt snapshot folder is pointing at it. But the distribution agent doesn't seem to be making an attempt to do read it. I tried changing the snapshot path to something that's incorrect and didn't even get an error saying that it couldn't access it. After lots of googling etc I found that sp_MSget_repl_commands is called by the subscriber on the distribution database on the publisher. Running a profiler I can see that it's only called for one agent Id. After a reinit it's called for sequence number 0x0 as expected so I thought that would mean it's would look for the snapshot. However, looking on the publisher I see that there's data for two agents - the snapshot agent and the log reader agent (which is being queries). So I guess I need to tell the distribution agent to get the data for both. But how? and more importantly - why? It worked fine on the other two servers I've replicated. I'm not an SQL novice but this is pretty much my first go at replication so don't be afraid to accuse me of missing something obvious/stupid! I can get log files (eg from the distribution agent) if you want but they don't seem to have any errors in them - it just starts up and starts applying log reader agent changes. Cheers Dave

  Read the article

• Strange monitor issue - screen goes black after a few seconds

  - by Scott Szretter

  My LCD monitor display is going black (turning off). It's a Samsung SYncMaster 2233 widescreen. I am trying to figure out if there is anything I can do about it, or if the monitor is junk. I have tried multiple computers, all have the same issue. I have tried a different vga cable, same issue. Power and video cables are tight / double checked. When I power on the monitor, the blue light turns on at the bottom. Then a second or two later the video comes up as expected and it looks fine. However, about 2-3 seconds after that, the screen goes black. The blue light is still on and solid at the bottom (blue light normally flashes when the monitor is sleeping). If I power cycle the monitor, same thing happens. With no computer connected or when I unplug the vga cable, I see the searching for signal message "digital", then the screen goes black. However it usually shows "digital" then "analog" after that and switches between the two a few times. The buttons on the side do not do anything, although they may be, I just can not see if they are or not. I can usually get the "digital" message by pressing the buttons on the side, but then it quickly goes black again. What is really strange is sometimes I can get it to work fine. I am not sure what the difference is. Last week I connected it up and it worked fine and it stayed fine for at least a week! I did not turn it off or anything, I just let the OS put the display to sleep. Then this week one morning I started having the screen going black issue again. Seems like something is either loose inside or beginning to fail. Do you think there is any hope for it? update: pushing the input select button causes the "digital" and "analog" messages to flash on the screen, but only for a few seconds then it goes black. When it was working properly, those messages would flash back and fourth for probably 10-20 seconds then a message would show saying check input signal, but now just a black screen.

  Read the article

• Repair BAD Sectors or Buy a new HDD?

  - by Nehal J. Wani

  I have a Seagate internal hard disk drive. I recently opened up my laptop [Dell Inspiron N5010] [Warranty has expired], cleaned it and it worked normally after waking up from hibernation. However, when I restarted it, it stuck on windows loading screen, then tried to boot from Dell recovery partition but failed. It gave the error: Windows has encounter a problem communicating with a device connected to your computer. This error can be caused by unplugging a removable storage device such as an external USB drive while the device is in use, or by faulty hardware such as a hard drive or CD-ROM drive that is failing. Make sure any removable storage is properly connected and then restart your computer If you continue to receive this error message, contact the hardware manufacturer. Status: 0xc00000e9 Info: An unexpected I/O error has occurred. While cleaning, I had mistakenly touched the round silvery thing at the bottom of the HDD. I don't know whether this has caused the problem or not. Since I have Fedora also installed in the same HDD, I can boot from it but it shows weird read errors when I ask it to mount Windows partitions. The disk utility also says that the Hard Disk has many bad sectors and needs to be replaced. I downloaded Seatools from Seagate website and used it. In the long test, I gave it permission to repair the first 100 errors which it did successfully. Now I am confused at what I should do. Internal Hard Disk Costs: a. Internal HDD 500GB Costs: Rs3518 b.1 External HDD 500GB Costs: Rs3472 b.2 External HDD 1TB Costs: Rs5500 c. Internal to External Converter Costs: Rs650 I have the following options: (i) Buy an External HDD, backup my data. Try to repair bad sectors of HDD. Then two cases arise: (a) My Internal HDD gets repaired [almost] (b) My internal HDD doesn't get repaired. Then I need to buy another internal HDD and replace the damaged one. OR break the seal of the external one and put it inside my laptop as internal. Breaking the case involves risks. (ii) Buy a Internal HDD and an Internal to External Converter Case [Not very reliable], backup my data. Try to repair bad sectors of HDD. Then two cases arise: (a) My Internal HDD gets repaired [almost] (b) My internal HDD doesn't get repaired. Then I need to just put in the new internal HDD I just bought. Experts, please guide me as to what will be the most VFM option? Also, if a HDD is failing, is it that I shouldn't read from it too otherwise there is a chance of other sectors failing? What I mean is, is it wrong to read from the HDD without taking backup first?

  Read the article

• Reach self hosted server from LAN

  - by Freefri

  I have a self hosted server with Apache2 pointed with the domain example.com. I have also some virtual servers www.example.com, cloud.examle.com, etc. This server is in my LAN, and when I try to acces to my server within the lan throw www.examle.com y get my router's configuration page. From outside the LAN www.example.com and cloud.examle.com works properly. From inside the LAN 192.168.1.33 (server internal IP) shows the default webpage (www.examle.com), but I can not get cloud.examle.com I also have a LAN name server in 192.168.1.33 with bind9. I set up my gateway 192.168.1.1 with my LAN-NS as primary NS I solve this problem creating a new dns zone in the NS. This are my config files: ;ZONE-1 $ORIGIN . $TTL 86400 ; 1 day home.lan. IN SOA server.home.lan. hostmaster.home.lan. ( 2008080901 ; serial 8H ; refresh 4H ; retry 4W ; expire 1D ; minimum ) home.lan. IN NS server.home.lan. $ORIGIN home.lan. ; Set the address for localhost.home.lan localhost IN A 127.0.0.1 router IN A 192.168.1.1 server IN A 192.168.1.33 mypc IN A 192.168.1.132 ;ZONE-2 $ORIGIN . $TTL 86400 ; 1 day example.com. IN SOA www.example.com hostmaster.home.lan. ( 2008080902 ; serial 8H ; refresh 4H ; retry 4W ; expire 1D ; minimum ) example.com. IN NS 192.168.1.33 $ORIGIN examle.com. localhost IN A 127.0.0.1 www IN A 192.168.1.33 cloud IN A 192.168.1.33 My DNS and my names are working properly now My question are: What do you think about my solution? Can I change the A zone with CNAME to server.home.lan (this is the domain in the LAN to the server)? How can I set a default IP for all my whatever.example.com?

  Read the article

• iotop for Linux kernel 2.6.18

  - by Lightsauce

  So it has to come to my attention that iotop isn't availalbe for 2.6.18 since it's less than 2.6.20 and requires Python 2.6+. I've done some research and came across this article: http://lserinol.blogspot.com/2009/09/io-usage-per-process-on-linux.html According to this, if these process have io stats in /proc/pid#/io (where pid# is the process #) it's doable regardless of the kernel version. So, in reality, I could upgrade Python to 2.6 and test out iotop. However, my flavor of Linux, CentOS release 5.5 (Final), only supports Python 2.4.3-44.el5 currently. If I were to do uninstall from yum, it doesn't look so pretty. It ends up wanting to uninstall 235 packages, most of which are very important! I read in one place, online (I forget the URL from yesterday), that you can install Python 2.6+ parallel to this one, and have the rpm install for iotop use that. Well, I didn't choose that route. I figured, what the heck, lets write iotop (not copying it, but reverse engineering it without actually looking at it's code/it in use) in bash. I thought it would just grab the /proc/pid#/io file and parse stats. So I wrote a script to grab the top 10 rchar, wchar, read_bytes, and write_bytes by collecting all these stats from all the /proc/pid#/io files, sorting them by each metric, then grabbing the top 10 highest values. The conclusion, the data seems completely useless. Does anybody know any resources for advanced Linux where I can figure out how to take these /proc/pid#/ directories and figure out what the heck they are doing with io on the disk? My main goal is to figure out what exactly is causing high load on my disk. I just know it's on the / partition (/dev/sda2 in this case), and I'm not really sure how to narrow it down without the help of iotop. If I run iostat to grab metrics for 1 minute, every second, the first result it gives me shows a high 'kB_read/s', so that makes me think, it's reading mostly. However, if I watch the update it gives me every second, it's actually just showing values for kB_wrtn/s. This makes me think the initial value iostat gives me is misleading.

  Read the article

• What is the probable failure - no BSOD, no event log, monitors sleeping, force reboot required

  - by Tyler

  Every 3 to 15 days, my PC freezes. This typically happens when the computer is idle, I'm coming home from work, back from vacation, etc. It's never happened while using my computer. The monitors are in power save mode The Caps Lock light on the (wireless) keyboard doesn't work Ctrl-alt-del has no effect, mouse (wireless) has no effect The hardware reset button and single press of power putton have no effect Computer does not appear on the network No BSOD, no memory dump Event logs have no errors or indications of problems near the time of crash. Only messages after reboot indicating that there was a reboot without a clean shutdown. Windows is set to never put the computer to sleep (just the display) Here are the vital stats of the build: OS Windows 8 Pro 64-bit CPU Intel i5-2400 Mobo Intel BOXDP67DE Micro ATX GPU MSI N460GTX Cyclone768D5/OC RAM CORSAIR XMS3 8GB (2 x 4GB) CMX8GX3M2A1333C9 PSU SeaSonic X Series X650 Gold System Drive Samsung 840 Pro 256 GB SSD Data Drive 2 x Western Digital WD20EARS 2TB in hardware RAID 1 Optical Lite-On DVD burner IHAS424-98 And here is the story of how the problem developed and what I've done to diagnose: January 2011, system built with Windows 7 64-bit, runs great. March 2011, Intel replaced the mobo because of the bad sata controllers. October 2012, upgrade to Windows 8 (problems start shortly after). January 2013, system freezes and causes network to fail for the whole house. Unplug the network cable and other devices and PCs can use the internet. Plug it back in, internet goes away for everyone. Reboot and everything is fine. March 2013, install Intel Gigabit CT PCI-E NIC, disable mobo nic in bios. Network strangeness goes away. Freezes are less frequent. Memtest shows no problems (20 passes). Early June 2013, replace Antec PSU with SeaSonic PSU. Mid June 2013, replace OCZ Vertex 2 SSD with Samsung SSD. Late June 2013, get frustrated and hope the community has some good ideas (I'm running out of budget to replace parts). My next plan of attack is setting "Turn off display" to Never and using a screen saver to see how that reacts on the next freeze. It makes me sad to waste power for up to 15 days though. Has anyone out there seen a problem like this? Any ideas on what kind of malfunction would act this way? Ideas of other diagnostic steps to take?

  Read the article

• Hyper-V Ubuntu Networking Problems Copying Large Amounts of Data

  - by Anonymous

  I am trying to copy a large amount (about 50 GB) of data over my network from a Hyper-V-hosted virtual machine running Ubuntu 11.04 (Natty Narwhal) to another (non-virtual) Ubuntu host that I plan to use for testing upgrades to one of our web applications. The problem I am having is with the virtual machine, which I shall refer to in what follows as "source.host". This machine is running 64-bit Ubuntu Server with the 2.6.38-8-server kernel and the Microsoft Linux Integration Components for Hyper-V kernel modules (hv_utils, hv_timesource, hv_netvsc, hv_blkvsc, hv_storvsc, and hv_vmbus) loaded. It uses a Hyper-V "synthetic network adapter" for its networking interface. To do the copy, I log on to the machine with the data and run the following commands (Call the remote machine "destination.host".): $ cd /path/to/data $ tar -cvf - datafolder/ | ssh [email protected] "cat > ~/data.tar" This runs for a while and then suddenly stops after transferring somewhere from 2-6 GB. The terminal on the source.host machine displays a Write failed: broken pipe error. The odd part is this: after this occurs, the "source.host" machine is no longer able to talk to the rest of the network. I cannot ping any other hosts on the network from the "source.host" machine, and I cannot ping the "source.host" machine from any other host on the network. I am equally unable to access the any of the web services hosted on "source.host". Running ifconfig on "source.host" shows the network adapter to be up and running as usual with the correct IP address and everything. I tried restarting the networking service with $ /etc/init.d/networking restart but the problem does not go away. Restarting the machine makes it capable of talking to the network again -- it can ping and be pinged by other hosts, and the web services are also accessible and usable as normal -- but attempting the copy operation again results in the same failure, requiring another restart. As an experiment, I tried replacing the tar -- ssh pipeline above with a straight scp: $ scp -r datafolder/ [email protected]:~ but to no avail Thinking that the issue might have to do with the kernel packet-send buffers filling up, I tried increasing the buffer size to 12 MB (up from the 128 KB default) with # echo 12582911 > /proc/sys/net/core/wmem_max but this also had no effect. I'm guessing at this point that it might be a problem with the Microsoft synthetic network driver, but I don't really know. Does anyone have any suggestions? Thank you very much in advance!

  Read the article

• Windows 2003 Server Caching

  - by pablomedok

  We're experiencing almost everyday table index corruption on Windows Server 2003. We are running an old application which uses DBF/CDX tables. Everything was fine for ages, but 6 months after we've installed Advantage Database Server (which allows access to some tables to our website) we started to get index corruption problems. And we don't know whom to blame. We've tried to exclude all possible causes of this corruption. Now all users work in terminal mode - so no network problems can cause that, OpLocks also can't be a reason. We changed hardware, network cards, switches, reainstalled Server and even moved to new dedicated server. The only thing we can't exclude is ADS - because it should be working. Is that possible that local read/write caching that causes that problem? E.g. one user or process uses cached data, later another user/process changes it, and later the first user changes it again without knowing about the first change. Is it possible theoretically? Is it possible that this problem is caused by imporper file server or caching settings? Is it possible that normal users use non-cached data and ADS is using cached data? Or vice versa? Is it possible that each terminal user has its own cache? Or maybe the problem is about RAID caching somehow interfering with Windows Server caching? Or maybe there are some special settings for Windows Server for working with DBF tables that are being written simultaneously by several terminal users? Maybe there is a way to turn off caching for some certain files to check it? Sometimes we get index crash twice a day, sometimes everything is fine for 5 days in a row. Today only one user was working in the evening with the database (usually there are 30-50 users are working simultaneously on working hours). So it's almost zero load on server. , Syncronization with website is performed every 5 minutes during work hours and every 15 minutes in the evening and on weekend. We've done file access auditing and it shows that during website syncroniztions ADS server opens the table and index files for ReadEA and WriteEA though it performs only SELECT queries. ADS does UPDATE/INSERT queries but less freqently - not during regular synchronizations, but only when an order is placed by website visitor). Please help me. We are struggling with this problem for almost a year and still can't find any pattern or any clue about this problem. Here is my previous qestion about this issue on DBA: http://dba.stackexchange.com/questions/8646/foxpro-dbf-index-corruption

  Read the article

• Linux: find out what process is using all the RAM?

  - by Timur

  Before actually asking, just to be clear: yes, I know about disk cache, and no, it is not my case :) Sorry, for this preamble :) I'm using CentOS 5. Every application in the system is swapping heavily, and the system is very slow. When I do free -m, here is what I got: total used free shared buffers cached Mem: 3952 3929 22 0 1 18 -/+ buffers/cache: 3909 42 Swap: 16383 46 16337 So, I actually have only 42 Mb to use! As far as I understand, -/+ buffers/cache actually doesn't count the disk cache, so I indeed only have 42 Mb, right? I thought, I might be wrong, so I tried to switch off the disk caching and it had no effect - the picture remained the same. So, I decided to find out who is using all my RAM, and I used top for that. But, apparently, it reports that no process is using my RAM. The only process in my top is MySQL, but it is using 0.1% of RAM and 400Mb of swap. Same picture when I try to run other services or applications - all go in swap, top shows that MEM is not used (0.1% maximum for any process). top - 15:09:00 up 2:09, 2 users, load average: 0.02, 0.16, 0.11 Tasks: 112 total, 1 running, 111 sleeping, 0 stopped, 0 zombie Cpu(s): 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 4046868k total, 4001368k used, 45500k free, 748k buffers Swap: 16777208k total, 68840k used, 16708368k free, 16632k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ SWAP COMMAND 3214 ntp 15 0 23412 5044 3916 S 0.0 0.1 0:00.00 17m ntpd 2319 root 5 -10 12648 4460 3184 S 0.0 0.1 0:00.00 8188 iscsid 2168 root RT 0 22120 3692 2848 S 0.0 0.1 0:00.00 17m multipathd 5113 mysql 18 0 474m 2356 856 S 0.0 0.1 0:00.11 472m mysqld 4106 root 34 19 251m 1944 1360 S 0.0 0.0 0:00.11 249m yum-updatesd 4109 root 15 0 90152 1904 1772 S 0.0 0.0 0:00.18 86m sshd 5175 root 15 0 90156 1896 1772 S 0.0 0.0 0:00.02 86m sshd Restart doesn't help, and, by they way is very slow, which I wouldn't normally expect on this machine (4 cores, 4Gb RAM, RAID1). So, with that - I'm pretty sure that this is not a disk cache, who is using the RAM, because normally it should have been reduced and let other processes to use RAM, rather then go to swap. So, finally, the question is - if someone has any ideas how to find out what process is actually using the memory so heavily?

  Read the article

• Why does this service refuse to start on Windows server 2003?

  - by PenguinCoder

  We have a Windows 2003 server with Cebos MQ1 (ver. 7 and ver. GRI) products installed that have been operational for years. After installing Microsoft 2010 C++ Redistributable package needed for other development, the MQ1 GRI service now fails to start. Event logs showed that two additional updates (.NET4 and the 2010 C++ Redistributable SP2) where installed by the redistributable as well. As soon as we discovered the MQ1 service was not starting properly, we removed these three installed packages. However the service still does not start; the dialog that pops up states 'The service started then stopped. '. Event logs when we attempt to start the service show nothing; IE: No errors, crashes, failures, or other information related to this service. Executing the MQ1Serv.exe directly specifies an issue of 'Missing command line operation, must specify install, uninstall and company abbreviation.' sc query MQ1Service(GRI) shows a clean exit for the Win32ExitCode of 0x0. Attempting to reinstall the client or server software gives an error of 'The procedure entry point ReInitializeCriticalSection could not be located in the dynamic link library KERNEL32.dll.' at the 'Registering Libraries' stage. At this point, further research has stated that the required function is in URL.dll and to verify the library is not corrupted. Running an sfc /scannow on the server has replaced a few DLLS; including the URL.DLL to versions from 2005. This actually broke other applications which required a reinstall (one of them being IE 7). After reinstall and updates, url.dll version is 7.0.5730.13 (2009) and Kernel32.dll is version 5.2.3790.4480 (2009). The MQ1 GRI service still will not start, specifying the same error as previous 'Service started then stopped'. Running a disassembler on Kernel32.dll and Url.dll show no functions named ReinitializeCriticalSection. Attempting the reinstall of the MQ1 client and server as well as starting the service again, fails once more. However, setting the compatibility mode on the MQ1 client install exe to 'Windows 95' actually gets the program to install. Setting the compatibility mode on the MQ1 server service does not enable it to start. I have been researching this problem for nearly a week and besides the advice to scan and replace url.dll, have come to no successful conclusions. This service was operational prior to the 2010 C++ install, without any additional parameters or settings. After removing the C++ install and all servicepacks/updates it installed silently, still does not correct the issue of the MQ1 GRI service not starting. Q: Has anyone else run into this or similar issue while attempting to get a service initialized? What have I overlooked or what else can I try in order to get this service started??

  Read the article

• Serving protected files using Nginx's X-Accel-Redirect header

  - by andybak

  I'm trying to serve protected files using this directive in my nginx.conf: location /secure/ { internal; alias /home/ldr/webapps/nginx/app/secure/; } I'm passing in paths in the form: "/myfile.doc" and the file's path would be: /home/ldr/webapps/nginx/app/secure/myfile.doc I just get 404's when I access "http: //myserver/secure/myfile.doc" (space inserted after http to stop ServerFault converting it to a link) I've tried taking the trailing / off the location directive and that makes no difference. Two questions: How do I fix it! How can I debug problems like this myself? How can I get Nginx to report which path it's looking for? error.log shows nothing and access.log just tells me which url is being requested - this is the bit I already know! It's no fun trying things randomly without any feedback. Here's my entire nginx.conf: daemon off; worker_processes 2; events { worker_connections 1024; } http { include mime.types; default_type application/octet-stream; server { listen 21534; server_name my.server.com; client_max_body_size 5m; location /media/ { alias /home/ldr/webapps/nginx/app/media/; } location / { proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; fastcgi_pass unix:/home/ldr/webapps/nginx/app/myproject/django.sock; fastcgi_pass_header Authorization; fastcgi_hide_header X-Accel-Redirect; fastcgi_hide_header X-Sendfile; fastcgi_intercept_errors off; include fastcgi_params; } location /secure { internal; alias /home/ldr/webapps/nginx/app/secure/; } } } EDIT: I'm trying some of the suggestions here So I've tried: location /secure/ { internal; alias /home/ldr/webapps/nginx/app/; } both with and without the trailing slash on location. I've also tried moving this block before the "location /" directive. The page I linked to has ^~ after 'location' giving: location ^~ /secure/ { ...etc... Not sure what that signifies but it didn't work either!

  Read the article

• Server to server replication and CPU and 32k\ corrupt doc

  - by nick wall

  Summary: if database contains a doc with 32K issue or corrupt, on server to server replication it causes marked increase in CPU in nserver.exe task, which effectively causes our server(s) to slow right down. We have a 5 server cluster (1 "hub" and 4 HTTP servers accessed via reverse proxy and SSO for load balancing and redundancy). All are physically located next to each other on network, they don't have dedicated network\ ports for cluster or replication. I realise IBM recommendation is dedicated port for cluster. Cluster queues are in tolerance and under heavy application user load, i.e. the maximum number of documents are being created, edited, deleted, the replication times between servers are negligible. Normally, all is well. Of the servers in the cluster, 1 is considered the "hub", and imitates a PUSH-PULL replication with it's cluster mates every 60mins, so that the replication load is taken by the hub and not cluster mates. The problem we have: every now and then we get a slow replication time from the hub to a cluster mate, sometimes up to 30mins. This maxes out the nserver.exe task on the "cluster mate" which causes it to respond to http requests very slowly. In the past, we have found that if a corrupt document is in the DB, it can have this affect, but on those occasions, the server log will show the corrupt doc noteId, we run fixup, all well. But we are not now seeing any record of corrupt docs. What we have noticed is if a doc with the 32K issue is present, the same thing can happen. Our only solution in that case is to run a : fixup mydb.nsf -V, which shows it is purging a 32K doc. Luckily we run a reverse proxy, so we can shut HTTP servers down without users noticing, but users do notice when a server has the problem! Has anyone else seen this occur? I have set up DDM event handlers for many of the replication events. I have set the replication time out limit to 5 mins (the max we usually see under full user load is 0.1min), to prevent it rep'ing for 30mins as before. This ia a temporary work around. Does anyone know of a DDM event to trap the 32K issue? we could at least then send alert. Regarding 32K issue: this prob needs another thread, but we are finding this relatively hard to find the source of the issue as the 32K event is fairly rare. Our app is fairly complex, interacting with various other external web services, with 2 way data transfer. But if we do encounter a 32K doc, we can't look at field properties, so we can't work out which field has issue which would give us a clue as to which process is culprit. As above, we run a fixup -V. Any help\ comments on this would be gratefully received.

  Read the article

• Need help recovering a corrupt SQL database

  - by user570079

  I have a very special case that I have been working on for several days. I have a very large SQL Server 2008 database (about 2 TB) that contains 500 filegroups to support very large partitioned tables. Recently we had a catastophic failure on one of the drive and lost several filegroups and the database became in-accessible. We have been doing filegroup backups on a daily basis, but due to other issues, we lost our most recent backup of the log and the primary filegroup. We have all the data backed up but the primary filegroup backup is old. There have been no schema changes since the primary filegroup backup, but the lsn's are now all out of sync and we cannot recover the data. I have tried everything I could think of (and have tried just about every trick and hack I could google) but I still end up at the same point where I get messages saying that the files for filegroup x do not match the primary filegroup. I am now at the point of trying to edit the system tables (we have a separate temporary environment to do this so we are not worried about corrupting any production databases). I have tried updated sys.sysdbreg, sys.sysbrickfiles, and sys.sysprufiles to try to trick SQL into thinking all the files are online, but a "Select * From OPENROWSET(TABLE DBPROP, 5)" shows a different database state from what I see in sys.sysdbreg. I am now thinking I need to somehow edit the headers of the actual data files to try to line up the lsn's with the primary. I appreciate any help anyone can give me here, but please do not respond with things like "you are not supposed to do edit mdf, ndf files...." or "see msdn article....", etc. This is an advanced emergency case and I need a real hack so we can just get to the data in this corrupt database and export to a fresh new database. I know there is a way to do this, but not knowing what the DBPROP system functions does (i.e. does it look at system tables or does it actually open the file) is keeping me from trying to figure out how to fool SQL into allowing me to read these files. Thanks for any help.

  Read the article

• vmdk to live cd - VMware vmxnet virtual NIC driver Kernel panic

  - by ronalchn

  Task I am trying to convert a virtual machine to a live CD. Specifically, the virtual machine I am trying to convert is the IOI 2013 Competition Environment. In this task, I am aided by a guide Converting a virtual disk image: VDI or VMDK to an ISO you can distribute. Symptoms However, after getting through all the instructions, the live CD causes a kernel panic on boot on bare metal. In particular, the screen shows: [0.737348] cdrom: Uniform CD-ROM driver Revision: 3.20 [0.737503] sr 3:0:0:0: >Attached scsi CD-ROM sr0 [0.737638] sr 3:0:0:0: >Attached scsi generic sg2 type 5 [0.737771] Freeing unused kernel memory: 756k freed [0.738093] Write protecting the kernel text: 5960k [0.738155] Write protecting the kernel read-only data: 2424k [0.738224] NX-protecting the kernel data: 4280k Loading, please wait... [0.752252] udevd[100]: starting version 175 [0.768708] VMware vmxnet3 virtual NIC driver - version 1.1.29.0-k-NAPI [0.781204] VMware PVSCSI driver - version 1.0.2.0-k [0.789555] VMware vmxnet virtual NIC driver [0.799356] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000200 [0.799356] [0.799472] Pid: 1, comm: init Tainted: G 0 3.5.0-17-generic #28-Ubuntu [0.799549] Call Trace: [0.799603] [<c15bf0ec>] panic+0x81/0x17b [0.799654] [<c104a6a5>] do_exit+0x745/0x7a0 [0.799707] [<c104a9a4>] do_group_exit+0x34/0xa0 [0.799760] [<c104aa28>] sys_exit_group+0x18/0x20 [0.799813] [<c15cff5f>] sysenter_do_call+0x12/0x28 Possible problem I suspect that the problem is the VMware vmxnet virtual NIC driver - however, I do not know how I can uninstall it, and possibly install one for a bare metal machine. If anyone knows which packages needs installing/uninstalling at the .rootfs/ chroot directory stage, please let me know. Details on procedure Do note that after importing the .ova file into Virtualbox, the virtual machine is stored as a .vmdk file already, and not a .vdi file. I would like to point out some results of the procedure followed in case of any questions. This is after extracting the filesystem from the .raw file to the .rootfs/ directory mentioned in the blog. I changed the filesystem table as mentioned in the blog, then looked at the possible "kernel optimized for virtualization". However, I found that linux-image-generic was already installed. Also, when running the command dpkg-query --showformat='${Package}\n' -W 'vmware-tools*' (or dpkg-query --showformat='${Package}\n' -W '*-virtual'), no packages were found. Thus, I did not find any virtualization specific packages. I proceeded to generate the iso following the steps in the blog, and burned it to a DVD.

  Read the article

• Ubuntu + SSL ports + AVAST

  - by jurajvt

  I have an interesting problem with communication via standard SSL ports. Fresh installed Ubuntu 14.04 server + Postfix + Dovecot, SASL authentication provided by Dovecot, self-signed certificate generated trough the Dovecot script mkcert.sh. Redirected ports on ZyWALL USG 200. I can send and receive e-mails from outside with standard ports 25 and 110, but not over 587. I am connecting to my server from machine with Windows 8.1 + VMWare Player + Ubuntu 14.04 Desktop + ssh. On Windows host I have installed Avast! antivirus. When I am trying to telnet from virtual machine to server over 587, it refused connection. But when I turn on Avast! it let me in to message Connected to... Same with nmap. When Avast! is turned on it is show me all SSL ports. When I turned it off, only standard ports appeared. OpenSSL shows me CONNECTED(00000003). But outside virtual machine directly in Windows 8.1 using nmap with zenmap there are not opened SSL ports in both Avast! states. From other external linux machines are problems with touching SSL ports same - refused. I have turned on submission in master.cf and 587 port is correctly listening on 0.0.0.0 in process master.pid which belongs to Postfix. I can telnet, or nmap over port 587 to my domain directly from server. Other ports like 995, 993 are OK on localhost, too. It is true, that I can't send emails via 587 anyway (Avast! turned on/off), but I can see ports opened. It is possible, that I have simply bad certificate and Avast! has right one, so with turned it on I can see opened ports? EDIT: To be more clear, I can't see or using port 587 everywhere from outside (tried Thunderbird, telnet, openssl, nmap, putty, swaks; both from Linux or Windows machines) and that is my problem. It was only by chance that I saw opened ports when Avast! is turned on.

  Read the article

• windows 7 virtual wireless adapter keeps going to sleep

  - by conners

  Just a quick question that I can't see mentioned anywhere online. I have a Windows 7 box configured like these guys recommend http://www.itgeekdiary.com/windows-7-as-an-wi-fi-access-point/ simply so that I can have my Windows 7 box as a wifi access point or a wifi emitter. It's also called a Microsoft Virtual WiFi Miniport Adapter. But it powers off and shuts down automatically and stops working. Basically everything works as intended and then - well -it will stopped working when I am not at the Windows 7 PC for a long time. The problem seems to be that every time my PC goes to "power save / sleep" and in the morning the Windows 7 machine "wakes" but blooming heck the wifi has stopped and you have to power cycle the PC (which is very uncool). When I power Cycle I have to do the following as administrator C:\Windows\System32\netsh.exe wlan start hostednetwork I then tried a gazllion things involving services and power management and eventually discovered that if I run the following commands as administrator it will be ok (for a bit) but every 3rd ot 4th time I try this "trick" it simply fails. the trick that seems to work 3 out of 4 times (i.e. "most" of the time) C:\Windows\System32\netsh.exe wlan stop hostednetwork C:\Windows\System32\netsh.exe wlan start hostednetwork But why does this only work "some" of the time? What else I did by myself: on every manage adapter properties (that relates to the wifi) I right clicked [configure] [power management] /disabled/ "allow the computer to power off to save power" <- this made no difference Also (and this is a bit annoying) there is no system tray app/GUI for the Microsoft Virtual WiFi Miniport Adapter output signal ... none... so (lame as it sounds) the ONLY way I can check if it's on is to physically go to another device and SCAN.. lame so my question can probably be solved by any of the following: a) can I stop Windows 7 sleeping this wifi when the machine sleeps b) can I force Windows to force wake this process on wake? if so how? c) what is the service / process REALLY called and how do I restart it if it crashes d) how can I flush the wifi properly rather power cycle the host machine e) anyone have a link to an program or app that can sit in the system tray that shows windows 7 wifi hotspot emission status (on/off/etc etc) Since I am a programmer I can easily write a vbs script / windows exe to fix this (and I will share this solution) and the gui problem if I can work out the actual service that is running that netsh stops/starts

  Read the article

• mdadm raid1 fails to resync

  - by JuanD

  Hello, I'm trying to solve this problem I'm having with an mdadm raid1. I have an ubuntu 9.04 server running on a software 2-drive raid1 with mdadm. Yesterday, one of the drives failed, and so I replaced it with a brand new drive of the same size. I removed the faulty drive, copied the partition from the remaining good drive to the new drive and then added it to the raid. It re-synced and the system worked fine, until the drive that hadn't failed, was also labeled failed. Now I had the raid running solely on the new drive. So I purchased another drive and repeated the procedure above. So now I had 2 brand new drives and the raid was syncing. However, after a few minutes I checked /proc/mdstat and the raid was no longer syncing. mdadm --detail /dev/md1 shows: (sdb is the first new drive, and sdc is the second new drive) root@dola:/home/jjaramillo# mdadm --detail /dev/md1 /dev/md1: Version : 00.90 Creation Time : Sat Dec 20 00:42:05 2008 Raid Level : raid1 Array Size : 974711680 (929.56 GiB 998.10 GB) Used Dev Size : 974711680 (929.56 GiB 998.10 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 1 Persistence : Superblock is persistent Update Time : Wed Jun 2 10:09:35 2010 State : clean, degraded Active Devices : 1 Working Devices : 2 Failed Devices : 0 Spare Devices : 1 UUID : bba497c6:5029ba0b:bfa4f887:c0dc8f3d Events : 0.5395594 Number Major Minor RaidDevice State 2 8 35 0 spare rebuilding /dev/sdc3 1 8 19 1 active sync /dev/sdb3 I've tried removing and re-adding the drive a few times, but the same thing happens. The raid fails to resync. I've looked at /var/log/messages, and found the following: Jun 2 07:57:36 dola kernel: [35708.917337] sd 5:0:0:0: [sdb] Unhandled sense code Jun 2 07:57:36 dola kernel: [35708.917339] sd 5:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Jun 2 07:57:36 dola kernel: [35708.917342] sd 5:0:0:0: [sdb] Sense Key : Medium Error [current] [descriptor] Jun 2 07:57:36 dola kernel: [35708.917346] Descriptor sense data with sense descriptors (in hex): Jun 2 07:57:36 dola kernel: [35708.917348] 72 03 11 04 00 00 00 0c 00 0a 80 00 00 00 00 00 Jun 2 07:57:36 dola kernel: [35708.917357] 00 43 9e 47 Jun 2 07:57:36 dola kernel: [35708.917360] sd 5:0:0:0: [sdb] Add. Sense: Unrecovered read error - auto reallocate failed So it looks like there's some kind of error on sdb (the first new drive). My question is, what would be the best approach to get the raid up and running again? I've thought about dd'ing the /dev/md1 to a blank hard drive, then re-doing the raid from scratch and loading the data back, but there could be an easier solution.. Any help would be appreciated.

  Read the article

• Can't recover hard drive

  - by BreezyChick89

  My drive got corrupt after a thunderstorm. It used to be 1 partition of 2.5tb but now it shows 2 partitions. It's weird because 300gig free space is about how much it had before corrupting, but it was part of the first partition. I tried $ sudo resize2fs -f /dev/sdb1 Resizing the filesystem on /dev/sdb1 to 536870911 (4k) blocks. resize2fs: Can't read an block bitmap while trying to resize /dev/sdb1 Please run 'e2fsck -fy /dev/sdb1' to fix the filesystem after the aborted resize operation. sudo e2fsck -f /dev/sdb1 e2fsck 1.42 (29-Nov-2011) The filesystem size (according to the superblock) is 610471680 blocks The physical size of the device is 536870911 blocks Either the superblock or the partition table is likely to be corrupt! Abort? n .... Error reading block 537395215 (Invalid argument) while reading inode and block bitmaps. Ignore error<y>? yes Force rewrite<y>? yes Error writing block 537395215 (Invalid argument) while reading inode and block bitmaps. Ignore error<y>? yes ... A lot of these. I can't use e2fsck -y because the first question aborts if I say "y". If I put a weight on the 'y' key it fails because none of the errors were really fixed. I asked this question before and tried using gparted but gparted fails because the first thing it does is: e2fsck -f -y -v /dev/sdb1 giving the same error. The disk status says healthy. There are no bad blocks. This is very frustrating because I can see the data in testdisk and it looks like it's all there. I already bought another 2.5tb drive and made a clone using dd. The next step if I can't fix this is to wipe that drive and just move the data with testdisk, but it seems certain folders will copy infinitely until the drive is full because of symlinks or errors so it's also a difficult option. sudo fdisk -l Disk /dev/sdb: 2500.5 GB, 2500495958016 bytes 255 heads, 63 sectors/track, 304001 cylinders, total 4883781168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0005da5e Device Boot Start End Blocks Id System /dev/sdb1 * 2048 4294969342 2147483647+ 83 Linux sudo badblocks -b 4096 -n -o badfile /dev/sdb 610471680 536870911 badfile is empty I also tried changing the superblock with "fsck -b" but all of them are the same.

  Read the article

• Bridging and iptables SNAT conflict

  - by sad_admin

  Hello I am working on a setup here and have it working with one minor exception. Devices on one side of my bridge aren't getting SNAT'd to the Internet. The Diagram / Overview: Primary_Network (Site_A) | | Internet ------- Linux_Bridge_GW (GW) | | Secondary/CoLo Site (Site_B) Here is the setup: 1.) Site_A has all the production servers and workstations. 2.) Site_B has a set of servers that we would like to fail-over to and also serve our internet facing services from. 3.) GW has two interfaces that are trunked and carrying the appropriate VLAN traffic (allow layer-2 propagation of traffic between sites) //this all works perfectly fine. 4.) The problem that is being encountered is, hosts from Site_B have their default GW at Site_A (same subnet) GW does not have IPs on the VLANs that are being passed. 5.) All hosts at Site_A can reach the Internet without problem. 6.) GW has an addresses on a subnet that is ONLY for Internet destined traffic. (This was done so that Websense would not have to parse unnecessary traffic. We use this VLAN as the monitor port's source on the switch where Websense is sitting). What I think is happening: 1.) Packet/Frame comes in on physdev at Site_B destined for Internet. 2.) Kernel sees packet, and forwards it out the other side of the bridge to that host's default GW. 3.) Site_A (containing core-network's Default-GW) sees that packet is destined for a host it doesn't know about, so it sends it to it's default GW (the linux bridge, since it's Internet bound). 4.) The kernel says "Hey, I've seen you before" and therefore doesn't do SNAT'ing on the packet and sends it out to the Internet where it's black-holed. Why I think it's happening: 1.) A tcpdump on the internet facing NIC shows the packet leaving the interface with the private address as it's source. What I would like: 1.) Have the packet SNAT'd. 2.) Something like the below would be awesome a.) packet comes in from Site_B b.) kernel sees that the packet is NOT destined for itself or any private address c.) kernel says "OK, well since you're destined for the Internet I'm going to send you out this interface rather than forward you to your normal default GW that's WAAAY over there." d.) packet comes in from internet and is sent out the appropriate bridge physdev depending on which site the host it's destined for is at. Thanks for any assistance or guidance that you are willing to offer. Best Regards, Sad Admin

  Read the article

• Google Rules for Retail

  - by David Dorf

  In the book What Would Google Do?, Jeff Jarvis outlines ten "Google Rules" that define how Google acts.  These rules help define how Web 2.0 businesses operate today and into the future.  While there's a chapter in the book on applying these rules to the retail industry, it wasn't very in-depth.  So I've decided to more directly apply the rules to retail, along with some notable examples of success.  The table below shows Jeff's Google Rule, some Industry Examples, and New Retailer Rules that I created. Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin-top:0in; mso-para-margin-right:0in; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0in; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin;} table.MsoTableGrid {mso-style-name:"Table Grid"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-priority:59; mso-style-unhide:no; border:solid black 1.0pt; mso-border-themecolor:text1; mso-border-alt:solid black .5pt; mso-border-themecolor:text1; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-border-insideh:.5pt solid black; mso-border-insideh-themecolor:text1; mso-border-insidev:.5pt solid black; mso-border-insidev-themecolor:text1; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin;} Google Rule Industry Examples New Retailer Rule New Relationship Your worst customer is your friend; you best customer is your partner Newegg.com lets manufacturers respond to customer comments that are critical of the product, and their EggXpert site lets customers help other customers. Listen to what your customers are saying about you.  Convert the critics to fans and the fans to influencers. New Architecture Join a network; be a platform Tesco and BestBuy released APIs for their product catalogs so third-parties could create new applications. Become a destination for information. New Publicness Life is public, so is business Zappos and WholeFoods founders are prolific tweeters/bloggers, sharing their opinions and connecting to customers.  It's not always pretty, but it's genuine. Be transparent.  Share both your successes and failures with your customers. New Society Elegant organization Wet Seal helps their customers assemble outfits and show them off to each other.  Barnes & Noble has a community site that includes a bookclub. Communities of your customers already exist, so help them organize better. New Economy Mass market is dead; long live the mass of niches lululemon found a niche for yoga inspired athletic wear.  Threadless uses crowd-sourcing to design short-runs of T-shirts. Serve small markets with niche products. New Business Reality Decide what business you're in When Lowes realized catering to women brought the men along, their sales increased. Customers want experiences to go with the products they buy. New Attitude Trust the people and listen In 2008 Starbucks launched MyStartbucksIdea to solicit ideas from their customers. Use social networks as additional data points for making better merchandising decisions. New Ethic Be honest and transparent; don't be evil Target is giving away reusable shopping bags for Earth Day.  Kohl's has outfitted 67 stores with solar arrays. Being green earns customers' respect and lowers costs too. New Speed Life is live H&M and Zara keep up with fashion trends. Be prepared to pounce on you customers' fickle interests. New Imperatives Encourage, enable and protect innovation 1-800-Flowers was the first do sales in Facebook and an early adopter of mobile commerce.  The Sears Personal Shopper mobile app finds products based on a photo. Give your staff permission to fail so innovation won't be stifled. Jeff will be a keynote speaker at Crosstalk, our upcoming annual user conference, so I'm looking forward to hearing more of his perspective on retail and the new economy.

  Read the article

• Installing Lubuntu 14.04.1 fails, upowerd appears to hang

  - by Rantanplan

  On the live-CD session, I tried installing Lubuntu double clicking on the install button on the desktop. Here, the CD starts running but then stops running and nothing happens. Next, I rebooted and tried installing Lubuntu directly from the boot menu screen using forcepae again. After a while, I receive the following error message: The installer encountered an unrecoverable error. A desktop session will now be run so that you may investigate the problem or try installing again. Hitting Enter brings me to the desktop. For what errors should I search? And how? Thanks for some hints! On Lubuntu 12.04: uname -a Linux humboldt 3.2.0-67-generic #101-Ubuntu SMP Tue Jul 15 17:45:51 UTC 2014 i686 i686 i386 GNU/Linux lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 12.04.5 LTS Release: 12.04 Codename: precise upowerd appears to hang: Aug 25 10:53:28 lubuntu kernel: [ 367.920272] INFO: task upowerd:3002 blocked for more than 120 seconds. Aug 25 10:53:28 lubuntu kernel: [ 367.920288] Tainted: G S C 3.13.0-32-generic #57-Ubuntu Aug 25 10:53:28 lubuntu kernel: [ 367.920294] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Aug 25 10:53:28 lubuntu kernel: [ 367.920300] upowerd D e21f9da0 0 3002 1 0x00000000 Aug 25 10:53:28 lubuntu kernel: [ 367.920314] e21f9dfc 00000086 f5ef7094 e21f9da0 c1050272 c1a8d540 c1920a00 00000000 Aug 25 10:53:28 lubuntu kernel: [ 367.920333] c1a8d540 c1920a00 d9e44da0 f5ef6540 c1129061 00000002 000001c1 0001c37b Aug 25 10:53:28 lubuntu kernel: [ 367.920351] 00000000 00000002 00000000 e2276240 00000000 00000040 c12b0ec5 c19975a8 Aug 25 10:53:28 lubuntu kernel: [ 367.920368] Call Trace: Aug 25 10:53:28 lubuntu kernel: [ 367.920389] [<c1050272>] ? kmap_atomic_prot+0x42/0x100 Aug 25 10:53:28 lubuntu kernel: [ 367.920404] [<c1129061>] ? get_page_from_freelist+0x2a1/0x600 Aug 25 10:53:28 lubuntu kernel: [ 367.920417] [<c12b0ec5>] ? process_measurement+0x65/0x240 Aug 25 10:53:28 lubuntu kernel: [ 367.920432] [<c1654c73>] schedule_preempt_disabled+0x23/0x60 Aug 25 10:53:28 lubuntu kernel: [ 367.920443] [<c16565bd>] __mutex_lock_slowpath+0x10d/0x171 Aug 25 10:53:28 lubuntu kernel: [ 367.920454] [<c1655aec>] mutex_lock+0x1c/0x28 Aug 25 10:53:28 lubuntu kernel: [ 367.920478] [<f857223a>] acpi_smbus_transaction+0x48/0x210 [sbshc] Aug 25 10:53:28 lubuntu kernel: [ 367.920489] [<c11858e1>] ? do_last+0x1b1/0xf60 Aug 25 10:53:28 lubuntu kernel: [ 367.920504] [<f857242f>] acpi_smbus_read+0x2d/0x33 [sbshc] Aug 25 10:53:28 lubuntu kernel: [ 367.920520] [<f881e0f1>] acpi_battery_get_state+0x74/0x8b [sbs] Aug 25 10:53:28 lubuntu kernel: [ 367.920535] [<f881e8a9>] acpi_sbs_battery_get_property+0x2a/0x233 [sbs] Aug 25 10:53:28 lubuntu kernel: [ 367.920549] [<c14fa61f>] power_supply_show_property+0x3f/0x240 Aug 25 10:53:28 lubuntu kernel: [ 367.920561] [<c114664f>] ? handle_mm_fault+0x64f/0x8d0 Aug 25 10:53:28 lubuntu kernel: [ 367.920573] [<c14fa5e0>] ? power_supply_store_property+0x60/0x60 Aug 25 10:53:28 lubuntu kernel: [ 367.920586] [<c1407d20>] ? dev_uevent_name+0x30/0x30 Aug 25 10:53:28 lubuntu kernel: [ 367.920597] [<c1407d38>] dev_attr_show+0x18/0x40 Aug 25 10:53:28 lubuntu kernel: [ 367.920608] [<c11dad15>] sysfs_seq_show+0xe5/0x1c0 Aug 25 10:53:28 lubuntu kernel: [ 367.920621] [<c119846e>] seq_read+0xce/0x370 Aug 25 10:53:28 lubuntu kernel: [ 367.920633] [<c11983a0>] ? seq_hlist_next_percpu+0x90/0x90 Aug 25 10:53:28 lubuntu kernel: [ 367.920644] [<c1179238>] vfs_read+0x78/0x140 Aug 25 10:53:28 lubuntu kernel: [ 367.920654] [<c11799a9>] SyS_read+0x49/0x90 Aug 25 10:53:28 lubuntu kernel: [ 367.920667] [<c165efcd>] sysenter_do_call+0x12/0x28 /var/log/installer/debug shows upower related error: Ubiquity 2.18.8 Gtk-Message: Failed to load module "overlay-scrollbar" Gtk-Message: Failed to load module "overlay-scrollbar" ERROR:dbus.proxies:Introspect error on :1.23:/org/freedesktop/UPower: dbus.exceptions.DBusException: org.freedesktop.DBus.Error.NoReply: Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken. Exception in GTK frontend (invoking crash handler): Traceback (most recent call last): File "/usr/lib/ubiquity/bin/ubiquity", line 636, in <module> main(oem_config) File "/usr/lib/ubiquity/bin/ubiquity", line 622, in main install(query=options.query) File "/usr/lib/ubiquity/bin/ubiquity", line 260, in install wizard = ui.Wizard(distro) File "/usr/lib/ubiquity/ubiquity/frontend/gtk_ui.py", line 290, in __init__ mod.ui = mod.ui_class(mod.controller) File "/usr/lib/ubiquity/plugins/ubi-prepare.py", line 93, in __init__ upower.setup_power_watch(self.prepare_power_source) File "/usr/lib/ubiquity/ubiquity/upower.py", line 21, in setup_power_watch power_state_changed() File "/usr/lib/ubiquity/ubiquity/upower.py", line 18, in power_state_changed not misc.get_prop(upower, UPOWER_PATH, 'OnBattery')) File "/usr/lib/ubiquity/ubiquity/misc.py", line 809, in get_prop return obj.Get(iface, prop, dbus_interface=dbus.PROPERTIES_IFACE) File "/usr/lib/python3/dist-packages/dbus/proxies.py", line 70, in __call__ return self._proxy_method(*args, **keywords) File "/usr/lib/python3/dist-packages/dbus/proxies.py", line 145, in __call__ **keywords) File "/usr/lib/python3/dist-packages/dbus/connection.py", line 651, in call_blocking message, timeout)

  Read the article

• SQL SERVER – Retrieve and Explore Database Backup without Restoring Database – Idera virtual databas

  - by pinaldave

  I recently downloaded Idera’s SQL virtual database, and tested it. There are a few things about this tool which caught my attention. My Scenario It is quite common in real life that sometimes observing or retrieving older data is necessary; however, it had changed as time passed by. The full database backup was 40 GB in size, and, to restore it on our production server, it usually takes around 16 to 22 minutes, depending on the load server that is usually present. This range in time varies from one server to another as per the configuration of the computer. Some other issues we used to have are the following: When we try to restore a large 40-GB database, we needed at least that much space on our production server. Once in a while, we even had to make changes in the restored database, and use the said changed and restored database for our purpose, making it more time-consuming. My Solution I have heard a lot about the Idera’s SQL virtual database tool.. Well, right after we started to test this tool, we found out that it really delivers what it promises. Using this software was very easy and we were able to restore our database from backup in less than 2 minutes, sparing us from the usual longer time of 16–22 minutes. The needful was finished in a total of 10 minutes. Another interesting observation is that there is no need to have an additional space for restoring the database. For complete database restoration, the single additional MB on the drive is not required anymore. We can use the database in the same way as our regular database, and there is no need for any additional configuration and setup. Let us look at the most relevant points of this product based on my initial experience: Quick restoration of the database backup No additional space required for database restoration virtual database has no physical .MDF or .LDF The database which is restored is, in fact, the backup file converted in the virtual database. DDL and DML queries can be executed against this virtually restored database. Regular backup operation can be implemented against virtual database, creating a physical .bak file that can be used for future use. There was no observed degradation in performance on the original database as well the restored virtual database. Additional T-SQL queries can be let off on the virtual database. Well, this summarizes my quick review. And, as I was saying, I am very impressed with the product and I plan to explore it more. There are many features that I have noticed in this tool, which I think can be very useful if properly understood. I had taken a few screenshots using my demo database afterwards. Let us see what other things this tool can do besides the mentioned activities. I am surprised with its performance so I want to know how exactly this feature works, specifically in the matter of why it does not create any additional files and yet, it still allows update on the virtually restored database. I guess I will have to send an e-mail to the developers of Idera and try to figure this out from them. I think this tool is very useful, and it delivers a high level of performance way more than what I expected. Soon, I will write a review for additional uses of SQL virtual database.. If you are using SQL virtual database in your production environment, I am eager to learn more about it and your experience while using it. The ‘Virtual’ Part of virtual database When I set out to test this software, I thought virtual database had something to do with Hyper-V or visualization. In fact, the virtual database is a kind of database which shows up in your SQL Server Management Studio without actually restoring or even creating it. This tool creates a database in SSMS from the backup of the same database. The backup, however, works virtually the same way as original database. Potential Usage of virtual database: As soon as I described this tool to my teammate, I think his very first reaction was, “hey, if we have this then there is no need for log shipping.” I find his comment very interesting as log shipping is something where logs are moved to another server. In fact, there are no updates on the database from log; I would rather compare it with Snapshot Replication. In fact, whatever we use, snapshot replicated database can be similarly used and configured with virtual database. I totally believe that we can use it for reporting purpose. In fact, after this database was configured, I think the uses of this tool are unlimited. I will have to spend some more time studying it and will get back to you. Click on images to see larger images. virtual database Console Harddrive Space before virtual database Setup Attach Full Backup Screen Backup on Harddrive Attach Full Backup Screen with Settings virtual database Setup – less than 60 sec virtual database Setup – Online Harddrive Space after virtual database Setup Point in Time Recovery Option – Timeline View virtual database Summary No Performance Difference between Regular DB vs Virtual DB Please note that all SQL Server MVP gets free license of this software. Reference: Pinal Dave (http://blog.SQLAuthority.com), Idera (virtual database) Filed under: Database, Pinal Dave, SQL, SQL Add-On, SQL Authority, SQL Backup and Restore, SQL Data Storage, SQL Query, SQL Server, SQL Tips and Tricks, SQL Utility, SQLAuthority News, T SQL, Technology Tagged: Idera

  Read the article

< Previous Page | 546 547 548 549 550 551 552 553 554 555 556 557  | Next Page >