Search Results

Search found 17976 results on 720 pages for 'old versions'.

Page 557/720 | < Previous Page | 553 554 555 556 557 558 559 560 561 562 563 564  | Next Page >

• Sparc Solaris 2.6 will not boot

  - by joshxdr

  I have a very old Sparc Solaris network that was working fine last week, but after a power outage none of the workstations will boot. The network looks like this: host A: solaris 2.6, shares /export/home to network by NFS host B: solaris 8, runs NIS server. Mounts /export/home/ by NFS. host C: RHEL5, shares /share to network by NFS. Mounts /export/home/ by NFS. I figured that the main problem was host A, since you need the home directories available for the other workstations to boot(?). Host A does not mount anything by NFS as far as I know. However, this workstation will NOT boot. The OBP bootup sequence looks like this: Boot device <blah> configuring network interface le0 Hostname <hostname> check file system <everything ok> check ufs filesystem <everything ok> NIS domainname is <name> starting router discovery starting rpc services: rpcbind keyserv ypbind done setting default interface for multicast: add net 224.0.0.0: gateway <hostname> <HANGS at this point> Is there some kind of debug mode so that I can get more detail as to why the workstation won't boot? Is my network structure inherently susceptible to power outage? Is there a way I can boot up to command line so I can at least turn off the NFS mounting?

  Read the article

• I can't get my PC to start up by a normal way.

  - by ssice

  I couldn't write a more accurate title. I am just unable to start the computer by pressing the Power On button. I checked the Power Supply and it seems to give good voltage values in every pin. And this is not a BIOS malfunction because of bad overclocking or anything that may come to your mind. And I will tell you why. It happens that EPS (or any ATX-based) power supply has the ability to be powered-on by the Motherboard by jumping the 13th pin of the 24-pin-ATX-connector to COM/GND. I did it, after pushing the power on button (without any visual response) and, pwhaa! The machine turned on. I was able to read (and even write, if I wanted) BIOS values and then start any OS installed. Machine starts, so it's not any kind of misconfiguration. It seems some hardware related. I am able to power the machine on only if I already pushed the power on button. Though pushing it without jumping the 13th pin to ground for a second does not power the machine. Of course, jumping the pin without pushing the power on button does not tell the motherboard anything, so the computer would not start up either. It's as if the logic that connects the power button with the 13th pin derivation to GND was unable to be activated. What can be the issue? How can I solve it? My configuration is as follows: CPU: AMD Phenom 9850 X4 Black Edition MB: ASUS Formula II AM2 RAM: 2x2GB Corsair Dominator 5-5-5-15 2T @ 1066MHz DDR2 Tested also with only 1 module GPU: 2x XFX nVIDIA GeForce 9600 GT XxX Alpha Dog Edition @ Core: 540Mhz [SLi] Power Supply: Xilence 700W (ATX 12V 2.3 / EPS 12V 2.92 compatible) PS: I know the machine is like 2 years old. I hardly use it now, but my parents do.

  Read the article

• Dynamic DNS Updates with Wireless and Wired interfaces

  - by Phaedrus

  We have offices full of Windows & Mac users who obtain IP addresses from a Windows DHCP server, which in turn updates Dynamic DNS entries. We are noticing major inconsistencies with the entries, and have found that the problem is occurring more on Macs than on windows, and even more when users are frequently switching from wired to wireless adapter, which makes sense, as this sequence occurs: User enables wired adapter and registers Proper DNS User enables wireless adapter and registers 2nd proper DNS entry user switches off wireless manually and 2nd entry remains improperly until scavenge. Our help desk folks rely heavily (maybe more than they should) on the dynamic entries as part of their business process. For example, the user submits a help desk ticket, and the staff member expects to be able to remote desktop to their machine by hostname, which is hyperlinked in the helpdesk ticketing app. We have implemented multiple solutions & band-aids to different symptoms of the problems such as: Using DNS Reservations for Macintosh PCs Using DNS Scavenging to remove old records Switching from a Cisco DHCP server to the Windows DHCP Server But no matter what we do, it seems impossible to maintain perfect records. Has anyone encountered this problem before? What is industry best practice? Comments & Suggestions are much appreciated, /P

  Read the article

• How to repair damaged repository (which has a centralized .svn directory)?

  - by Heinrich Ulbricht

  I recently upgraded my TortoiseSVN installation to version 1.7.1. This forced me to upgrade my working copy as well. The upgrade removed all (but one) of the .svn directories from all subdirectories leaving only one in the root. Now out of the blue (of course; I suspect my antivirus software) there is an error when I for example try to clean up the working copy. I am also not able to commit anything. The error message when cleaning up is: Cleanup failed to process the following paths: C:\svn Can't open file 'C:\svn.svn\pristine\73\73bcc5fa7819f84f56b81dfa0236f0aac7b7d404.svn-base': The system cannot find the file specified. I traced the error to be related to the presence of one directory within the working copy. If I rename it then everything works. When it is present I get the error. I also deleted it and checked it out again. No change, the error persists. With previous versions I could repair damages in the .svn easily: just delete the offending folder and check out again. I cannot do this anymore because now the .svn dir is centralized. What could I do to repair my working copy?

  Read the article

• BIOS not detecting working SATA hard drive

  - by user28927

  Some time ago my power supply died. It's a long story from then till now, but the important bit is that I ended up with a new hard drive and a new power supply. I tested to see if my original hard drive was still alive, and it booted and worked perfectly until I turned it off. When I started it again it would not boot. I bought new SATA cables, assuming that the one I had was not seating properly (it was cheap and wobbly), but no dice. Upon start-up I am presented with a message telling me to insert boot media into the selected drive or add a drive and restart. Neither the new or the old drive is detected by BIOS, my Vista install disk, or from my bootable Linux USB drive. When I remove all of the RAM the computer ceases outputting visual information, and upon reinstalling the ram and starting up again gives me a "failed overclock" error. So, does anyone have an idea as to what might be going on? I'm completely lost at this point.

  Read the article

• How can I restore my laptop from Windows 7 to its original Windows Vista recovery partition?

  - by Cam Jackson

  I bought my Acer laptop 4 years ago with Vista Home Premium x86. It has a recovery partition that I have used successfully in the past to format everything and reinstall Windows to factory settings. I have since upgraded to Windows 7, but I now need to get back to my original installation. Not sure what it's called, but I can successfully get into this recovery thingy: However, when I click the third option (for me I think it says 'Windows Image Recovery' or something like that) it tells me that it can't find any images to recover from :( I have checked and I don't have a windows.old that I can recover from either. One final note, if I launch diskmgmt.msc, these are the partitions: Why is the first partition shaded? Does that mean anything? Both of the 'unlettered' partitions are 100% empty. Did the Windows 7 upgrade process format my Vista system recovery partition?! And finally: How can I get back to my factory settings? EDIT: I did see this question, but neither of the answers apply to my situation. Edit to address jdh's answer: From what I can tell, I never get the option to boot the Vista recovery partition. After hitting F10, I get this screen, except it's partition 2, and I don't have the IN/MINT bit: I hit Escape, and then I get this screen, except without Ubuntu listed, and without the auto-countdown thing: I hit F8, and then I get this screen: I hit Enter on the first option, I end up at the screen in the first screen shot. As I said, from there I click the third option, and it fails to find the image, which I guess makes sense if it's only looking for a Windows 7 recovery. So I either need to make the Windows 7 tool see the Vista recovery partition, or I need the boot loader (?) to let me select Vista earlier in the process. Any ideas?

  Read the article

• Games, Windows 8.1 and 144Hz display

  - by Marioysikax

  So I have been having problems with few games after switching from 7 to 8.1, which seems to be related to my 144Hz monitor. Few examples: Shank, Shank 2, Blood of the Werewolf, Astebreed, the Sims 2 and Rayman Legends patch 1.2Had few other as well but it's been long and I have 600+ steam library. From those games at least the Sims 2 and Shank worked without any problems with same setup and Windows 7. So basically these games simply refuse to launch with basic setup. However if I plug 60Hz TV with HDMI instead everything magically starts to work. As for Astebreed and the Sims 2 using windowed mode seems to also work. As for Rayman Demo and version 1.0 works for some reason and 1.2 breaks settings menu. I have already tried contacting supports. EA support stated game simply shouldn't work with 8.1 at all (which is lie as it works with that TV and friend with 8 plays just fine), ubisoft support took few weeks and support said he will forward info for further processing, blood of the werewolf support had no idea what's going on and told me to just use my TV instead.Changing monitors refresh rate to 120Hz or forcing it to 60Hz doesn't do anything. I have DVI right now but I will try with DisplayPort when I get the cable. At PCGW Garrett said it may have something to do how listing resolutions work with 8 compared to earlier Windows versions but my googling skills don't bring anything up and compatibility mode for earlier windows version doesn't work either (not that I expected that to work). My system specs are on my steam profile. How do I get those work with my 144Hz monitor as well as possible future games having same problem? Downgrading to 7 would work but is far from practical and I don't own legit lisence for that one.

  Read the article

• Firefox takes a really long time to load some sites on Ubuntu

  - by Dave

  Hello guys, I have an issue here. Some sites - just a few - takes a really long time to load on Firefox. One example is A List Apart (http://www.alistapart.com/) which takes more than 30 minutes (yes, minutes, not seconds). On Opera, ou even through a telnet session, the problematic sites run without problem, fast as expected. I am using Linux 8.04, running Firefox 3.6.3 downloaded from mozilla site, with a 10M ADSL connection. I tried many tweaks I found googling, like disable IPv6, and change http pipelining settings on FF's about:config. None worked. I also used Firebug to find what phase during negotiation is the bottleneck. Findings are in the screenshot. Well guys, any idea what is the issue? And how to solve it? I repeat, this only happens with firefox (3.6.3 and prior versions), for a few sites only (even sites with much more requests, images, javascripts, stylesheets work fine), and http pipelines and IPv6 tweaks on about:config didn't work. Thanks

  Read the article

• BIOS and Windows cannot detect CDROM device

  - by eman

  Hello! I have a HL-DT-ST RW/DVD GCC-4521B dvdrom device and a big problem. Some days ago everything worked fine. A friend installed some software and then the drives in winxp has been marked as corrupt. I uninstalled the software, but still corrupt drives. The next step I have done was running the current software GCC-4521B101(E).exe. When I ran this software again, the drives was automatically updated, but still marked as corrupt (in the Device Manager), even if I did a reboot. And then the big mistake: once more I tried to run this software, but during the update process, the machine restarted and boom! The DVDROM device doesn't work anymore. The led doesn't blink and if I push the eject button, nothing happens. Also bios and winxp doesn't recognize the optical drive. Then I plugged an other optical drive and it worked, but my old drive seems to be dead. So, what happened and how to solve this problem? Please help. Regards!

  Read the article

• Recover data from Dynamic Disk (MBR) bigger than 2TB

  - by Helder

  Here is the situation: Promise Array FastTrak TX4310 with 3 disks (750 GB each) in RAID5. This comes to around 1500 GB of data. Last week I had the idea of expanding the RAID with an additional 750 GB disk. This would bring the volume to around 2250 GB. I plugged the disk and used the Webpam software to do the RAID expansion. However, I didn't count with the MBR 2TB limit, as I didn't remembered that the disk was using MBR instead of GPT and I didn't check it prior to the expansion. After a couple of days of expansion, today when I got home, the disk in Windows disk manager showed the message "Invalid disk" and when I try to activate it, it says "The operation is not allowed on the Invalid pack". From what I figured, the logical volume on the RAID expanded, and passed that info to the Windows layer and I ended up with an "larger than 2TB" MBR disk. I'm hopping that somehow I can still recover some data from this, and I was wondering if I can "rewrite" the MBR structure back to the 1500 GB partition size, so I can access the partition in Windows. Right now I'm doing an "Analyse" with TestDisk, as I hope the program will pickup the old 1500 structure and allow me to somehow revert back to it. I think that even though the Logical Drive in the RAID is bigger than the 2TB, I can somehow correct the MBR to show the 1500 GB partition again. I had a similar problem once, and I was able to recover the data using a similar method. What do you guys think? Is it a dead end? Am I totally screwed because there is the extra RAID layer that I'm not counting? Or is there other way to move with this? Thanks all!

  Read the article

• how to diagnose a hard system seizure? Dell+Ubuntu

  - by rob

  I've got Ubuntu 9.10 on a Dell Vostro 420 desktop, a little over a year old, which I use for plain vanilla work stuff (email, web, terminal, text editor). Every now and then, at totally random times, it completely freezes on me. Hard. Mouse and keyboard stop working, cursor stops blinking, clock stops moving. All I can do is hold down the power button on the front of the box to shut it off. Sometimes it happens after several months of continuous uptime; sometimes it happens a few minutes after a reboot, while all I've done is open a terminal to look at log files, or maybe firefox to do a google search. Each time, there is nothing at all in /var/log/messages at the time of the crash. This makes it seem like a hardware problem, and indeed a few months ago I opened the box and wiggled everything and the problem went away for a while. But now it's back. I went in and checked everything, took out each RAM card and reseated. No luck. I ran all the system diagnostics (the long version) and everything passed with flying colors. Something is messed up in this box, but without any useful logs or failed tests, how in the world am I going to find it? And of course, Dell's not gonna help me cause I went and replaced Windows with Ubuntu. What steps would you take next to track down this problem?

  Read the article

• Index a low-cost NAS on Windows 7

  - by JcMaco

  Has anyone found a way to index the files stored on a Networked Attached Storage on Windows 7 so that the files can be available in Windows Search and Libraries? I am referring to the cheap and available NAS like the Western Digital My Book series that use an embedded linux server. Similar question: http://windows7forums.com/windows-7-networking/6700-indexing-nas-drive-libraries.html EDIT Windows help proposes to make the files stored on the NAS available offline. This is obviously not a good solution if the NAS has more data than what the client can store. If the folder is on a network device that is not part of your homegroup, it can be included as long as the content of the folder is indexed. If the folder is already indexed on the device where it is stored, you should be able to include it directly in the library. If the network folder is not indexed, an easy way to index it is to make the folder available offline. This will create offline versions of the files in the folder, and add these files to the index on your computer. Once you make a folder available offline, you can include it in a library. When you make a network folder available offline, copies of all the files in that folder will be stored on your computer's hard disk. Take this into consideration if the network folder contains a large number of files.

  Read the article

• Generic/Text Printer on Windows 7 not prompting for file name

  - by Trevor Tippins

  Hope someone can shed some light on this. I am downloading reports from an AIX-based system by directing them to a TT printer which the terminal emulator (MultiView 2000) intercepts and directs to the default printer on the local system. This local printer is configured as a vanilla Generic/Text printer attached to a FILE port. When I print from AIX, the output is spooled down and the local printer prompts for a file name into which to save the file...but not under Windows 7. This has worked fine for many years, on both Win2K and WinXP. However, on Windows 7 the output gets spooled as a file into spool\PRINTERS (and looks as expected) but the print job then hangs with a status of "Error - Printing" and never prompts for a file name. I have to cancel the job. The Generic/Text printer works as expected with other applications. I have tried setting the printer to print directly rather than spooling but this only serves to hang the terminal session too. I've also tried to run the emulator in Windows 2000 Compatibility Mode and as Administrator in case it was something like that but with no luck. As you might expect, it does work fine in XP Mode (as long as I print to a printer defined therein and not the host's printer) but operationally this isn't going to be an option. Obviously this emulation software is a decade old (at least) and I could just cross/upgrade all the users (at a cost) but, before I do so, has anyone seen this sort of behaviour before and found some sort of fix? Remote OS: AIX 5 Client OS: Windows 7 Pro (32-bit) Printer: Generic/Text on a FILE port TE Software: MultiView 2000 (32-bit) Thanks in advance.

  Read the article

• Connecting a laptop to a TV via HDMI

  - by Madmartigan

  I just bought a new Dell XPS17 laptop (Win7) that only has HDMI output. My last 2 laptops had VGA, which I used to connect to my Sony Bravia 32" TV with no issues, but with the HDMI it's been quite a headache. Drivers for display adapters have been updated to the latest versions: Intel(R) HD Graphics Family NVIDIA GeForce GT 550M I went to a store and plugged in to 4 different TVs from different manufacturers. A sales rep and I spent about 30 minutes being baffled by the results (which are the same as my current TV): Extreme buggy behavior in the Nvidia and Windows display/resolution control panel Can not extend or duplicate displays, can only select one Third and fourth output devices "randomly" detected by the Windows control panel Could not get the screen to fit the output (edges cut off on all sides by about a half inch) Resolution and colors less than perfect. Artifacts around text. Display "randomly" cuts out Defaults to TV output only when plugged in Can not change resolution on either device when connected No audio from the TV Plugged in to 3 monitors from different manufacturers: Defaults to duplicated displays when plugged in Everything works perfectly So far, four people have gone through all the settings in the latop with no luck. I had similar, but not exactly matching results with a different laptop. I'm using the Sony Bravia currently at home, but in order to get it to work I have to turn on the laptop, wait until the display shows up on it, close the lid, then cycle through each output channel on the TV until I come back around to the HDMI port again, but still I have the symptoms described above. However: Once in a while, it just works. Sometimes, seemingly randomly, the output fits the screen perfectly. Sometimes the audio comes through the speakers too, but not always. Usually my screen saver "Mystify" will come up with a message that it cannot be displayed due to a limitation of the video card, but then sometimes it works fine. These 3 things seem to be independent of each other and don't always happen together. So, is there any way to get the laptop to output correctly to a TV, or is it just not meant to be?

  Read the article

• USB question (how durable is it, how should I workaround this)

  - by Shiki

  The plot is quite simple. Got a Razer mouse. If I plug it in, it works. After a shutdown/hibernation, I have to replug it entirely at the back of the PC. (It works in my laptop even after severel shutdown, etc, so yes I guess it's my motherboard.. but it still got 2 years of warranty and it comes with quad SLI, its not an old motherboard at all. (MSI P7N SLI FI (bought it after a hungarian guy's recommendation)). So. I only could come up with one "solution". Get 3 USB cable (you know, USB-USB). If its possible the shortest ones (don't know if the responsibility/anything will worsen), AND replug only the middle+closest to the USB port junction, since those are replaceable. What do you think? Any other idea? (BIOS is updated, mouse driver ... doesn't really matter, the mouse won't even blink a bit after this happens. It lights up and goes totally dead.)

  Read the article

• why does the partition start on sector 2048 instead of 63

  - by gcb

  I had two drives partitioned the same and running 2 raid partitions on each. One died and I replaced it under warranty for the same model. While trying to partition it, the first partition can only start on sector 2048, instead of 63 that was before. Driver have different geometry as previous and remaining ones. (Fewer heads/more cylinders) old drive: $ sudo fdisk -c -u -l /dev/sdb Disk /dev/sdb: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000aa189 Device Boot Start End Blocks Id System /dev/sdb1 * 63 174080339 87040138+ 83 Linux /dev/sdb2 174080340 182482334 4200997+ 82 Linux swap / Solaris /dev/sdb3 182482335 3907024064 1862270865 fd Linux raid autodetect remanufactured drive received from warranty: $ sudo fdisk -c -u -l /dev/sda Disk /dev/sda: 2000.4 GB, 2000398934016 bytes 81 heads, 63 sectors/track, 765633 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000d0b5d Device Boot Start End Blocks Id System /dev/sda1 2048 ... why is that?

  Read the article

• Logitech Performance MX Mouse Jumps on OS X Lion (10.7.4)

  - by Adam Thompson

  I have a Logitech MX Revolution wireless mouse that I am trying to use with OS X Lion. Everything is working except for one problem... there is a small, but quite noticeable, jump when the mouse cursor is moved. The problem is mostly prevalent when dragging and dropping files or trying to highlight items. It makes performing any task with the mouse accurately next to impossible. I did quite a bit of looking and found that all kinds of people have had mouse issues with OS X. I've tried all of the following with absolutely no success: Using the official drivers from Logitech (these performed worse than the default mouse drivers in OS X) Using SteerMouse as a third party mouse driver. This worked ever so slightly better than the default driver, but still suffered quite frequently from the skipping problem Cleaning the sensor on the mouse and ensuring it's not the result of the surface that it's being used on. Tested the mouse on a Windows machine. The mouse worked absolutely flawlessly on the other machine. Changed the channel that my wireless router operates on by the off chance my problems were the result of interference. This also had no effect. I can't think of anything else that could possibly interfere with the mouse. I'm am out of ideas on what to try, so I would really appreciate if anyone has any suggestions. I should also mention that an old wired mouse I had laying around worked just fine when I plugged it in. This really isn't the best solution, however, as I really prefer the MX Revolution.

  Read the article

• Windows-to-linux: Putty with SSH and private/public key pair

  - by Johnny Kauffman

  I spent about 3 hours trying to figure out how to connect to a linux box from my windows machine using putty without having to send the password. This is connecting to an Ubuntu server that is using OpenSSH. The private key is SSH-2 RSA, 1024 bits. I am connecting using SSH2. I have run into the more common problems already: Putty generated the public key in the "wrong format". I have corrected this (as seen on this blog post). However, since I am not yet connected, I cannot absolutely confirm that this file is in the correct format. The key is all on a single line now, and I have tried adding/removing line breaks at the end of the file. I've also tried the public file doctoring process a few times to ensure that I haven't flubbed up the manual conversion. Even so, I have no way to verify accuracy here. The permissions were at once point wrong as well, specifically meaning that the file had too many permissions. I had to solve this too and I know it got past this because I no longer see a related error in /var/log/auth.log. I've tried both authorized_keys and authorized_keys2 in case the server has an old version of OpenSSH, but this changed nothing. I do have access as a user. After this keyfile stuff fails, I can enter my password instead The only remaining nibble of information I have is that it claims I have the alleged password wrong: sshd[22288]: Failed password for zzzzzzz from zz.zz.zz.zz port 53620 ssh2 Even so, as far as I can tell, this is just a lazy try/catch somewhere, since I don't think there's a password involved at all. I see nothing else in any of the /var/log files of use. What else could be wrong?

  Read the article

• How to know whether mongodb is running on 64 bit mode or 32 bit mode

  - by Jim Thio

  My programmer install mongodb. Then somehow it doesn't work. I run C:\mongod\bin>mongod mongod --help for help and startup options Sat Aug 11 22:57:50 Sat Aug 11 22:57:50 warning: 32-bit servers don't have journaling enabled by def ault. Please use --journal if you want durability. Sat Aug 11 22:57:50 Sat Aug 11 22:57:50 [initandlisten] MongoDB starting : pid=3800 port=27017 dbpat h=/data/db 32-bit host=haryantoi5 Sat Aug 11 22:57:50 [initandlisten] Sat Aug 11 22:57:50 [initandlisten] ** NOTE: when using MongoDB 32 bit, you are limited to about 2 gigabytes of data Sat Aug 11 22:57:50 [initandlisten] ** see http://blog.mongodb.org/post/13 7788967/32-bit-limitations Sat Aug 11 22:57:50 [initandlisten] ** with --journal, the limit is lower Sat Aug 11 22:57:50 [initandlisten] Sat Aug 11 22:57:50 [initandlisten] db version v2.0.7-rc1, pdfile version 4.5 Sat Aug 11 22:57:50 [initandlisten] git version: 9efe4cce272373b52b96de1309c1fbf 0c984305f Sat Aug 11 22:57:50 [initandlisten] build info: windows sys.getwindowsversion(ma jor=6, minor=0, build=6002, platform=2, service_pack='Service Pack 2') BOOST_LIB _VERSION=1_42 Sat Aug 11 22:57:50 [initandlisten] options: {} ************** Unclean shutdown detected. Please visit http://dochub.mongodb.org/core/repair for recovery instructions. ************* Sat Aug 11 22:57:50 [initandlisten] exception in initAndListen: 12596 old lock f ile, terminating Sat Aug 11 22:57:50 dbexit: Sat Aug 11 22:57:50 [initandlisten] shutdown: going to close listening sockets.. . Sat Aug 11 22:57:50 [initandlisten] shutdown: going to flush diaglog... Sat Aug 11 22:57:50 [initandlisten] shutdown: going to close sockets... Sat Aug 11 22:57:50 [initandlisten] shutdown: waiting for fs preallocator... Sat Aug 11 22:57:50 [initandlisten] shutdown: closing all files... Sat Aug 11 22:57:50 [initandlisten] closeAllFiles() finished Sat Aug 11 22:57:50 dbexit: really exiting now It seems that mongod is running on 32 bit. I have a 64 bit computer and I want to run mongodb in 64 bit enviroment. How do I do so?

  Read the article

• Strange sound behavior

  - by caarlos0

  First of all, sorry for the tittle. English isn't my native language, and I can't find a word to describe the strange behavior I'm getting here. In the most simple explanation, is like sound keeps going down and up again... Think in a kid with that old radios that have a circled volume button. Think like these kid keeps "turning" the volume button. That is the behavior I'm getting here. At first, I believed that it was a pulseaudio issue, but, it isn't. I followed the wiki part I think that should be my problem, but it didn't work. After that, as I'm using XFCE, I didn't really need pulseaudio, so I removed it and stays with a clean alsa, hopping that will fix my problem. Sweet mistake. It really looks like a kid looking for trouble. I believed it worked, and, suddenly, here is the same issue again. BTW: I have a full-upgraded testing system (yeah, I upgraded to testing hopping for new pulseaudio version which fix the issue), no pulseaudio at all, just xfce, started with startxfce. What can I do to fix this? It's extremely annoying... sometimes I just want to throw my laptop in the wall because of this. Any extra info you need, please, tell me. Thanks in advance -- EDIT: My alsamixer is like this: And here is a video with the sound behavior.

  Read the article

• Moving Microsoft Exchange server to the private network.

  - by Alexey Shatygin

  In one of the offices, we have a 50-computers network, which had only one server machine: Windows 2003 Server Microsoft ISA Server Microsoft Exchange 2003 This server worked as a gateway (proxy server), mail server, file server, firewall and domain controller. It had two network interfaces, one for WAN (let's say 222.222.222.222) and one for LAN (192.168.1.1). I set up a Linux box to be the gateway (without a proxy), so the Linux box now has the following interfaces: 222.222.222.222 (our external IP, we removed it from the Windows machine) and 192.168.1.100 (internal IP), but we need to keep the old Windows server as a mail server and a proxy for some of our users, until we prepare another Linux machine for that, so I need the mail server on that machine to be available from the Internet. I set up iptables rules to redirect all the incoming connections on the 25th and 110th ports of our external IP to 192.168.1.1:25 and 192.168.1.1:110 and when I try to telnet our SMTP service telnet 222.222.222.222 25 I get the greetings from our windows server's (192.168.1.1) SMTP service, and that's works fine. But when I telnet POP3 service telnet 222.222.222.222 110 I only get the blank black screen and the connection seem to disappear if I press any button. I've checked the ISA rules - everything seems to be the same for 110th and 25th ports. When I telnet on 110th ports of our Windows server from our new gateway machine like this: telnet 192.168.1.1 110 I get the acces to it's POP3 service: +OK Microsoft Exchange Server 2003 POP3 server version 6.5.7638.1 (...) ready. What sould I do, to make the POP3 service available through our new gateway?

  Read the article

• Windows 7 ignores F6/F8 and will not boot

  - by P.Brian.Mackey

  I have a work PC with sophos safeguard encryption on it. Windows failed to start. When I bootup I receive an error saying a recent hardware or software change might be the cause. File: \Boot\BCD Status: 0xc0000098 Info: The windows boot configuration data file does not contain a valid OS entry. This began after the PC forced me to run a system recovery. My machine had powered down improperly (power outage?) and simply would not respond to my keyboard input to cancel the option to scan my system. After the scan "repaired" a boot file, my system crashed. Now it tells me I can insert my windows 7 disk and run recovery. I can't simply do this because of Safeguard. The system recovery can't see my encrypted drive. I tried hitting F2 to manually login to Safeguard and then selected the option to boot from media. The computer prompts me to hit any key to boot from disk...which I do, but once again it is not reading my keyboard input. I can't get F8/F6 to bypass startup files and get me to a command prompt like the old days. If I could get to a command prompt I might could recover the file windows jacked up from its backup location...though I may need to use the windows recovery disk UI to do this..??? In the past I've been able to slap in a PS/2 keyboard when the USB keyboards stop responding like this. I have no PS/2 keyboard available. Anyone have any idea how I can undo the damage windows system recovery has done with safeguard installed?

  Read the article

• Looking for some IIS redirect help/ideas

  - by CoreyT

  Right now we have a site with a LOT of static asp pages such as, www.site.com/123.asp. This is due to how our current site's CMS builds it's pages by default. I don't have an exact count but we have roughly 6000 asp files in the site right now. We are in the middle of a redesign and restructuring of the site, and are looking to migrate to SEO friendly URLs. The problem we're having right now is what do we do to redirect the old pages to the new friendly URLs? I know how to do redirects that is not the issue here. The problems I am coming up with right now are listed below. 1 - Is there a limit to the number of redirects in IIS? 2 - Would having even a few thousand redirects affect IIS performance? 3 - My understanding is that we would not be passing along page rank to the new URLs, is that true? (not a major question I can ask on more SEO forums if nobody here is sure) 4 - Would using something like the IIS URL Rewrite 2 module for IIS 7 help us out? Or would I still need to define several thousand unique redirects in it? Our server right now is running Server 2003, however in the redesign I would be open to migrating to Server 2008 R2 if there is a good case for it (i.e. the URL Rewrite module). Thanks for any guidance or help. I have been looking for a good way to do this for a while now and keep coming up with things that sound problematic and bad (such as having 6000 redirects).

  Read the article

• Log shipping on select tables.

  - by Scott Chamberlain

  I know I am most likely using incorrect terminology so please correct me if I use the wrong terms so I can search better. We have a very large database at a client's site and we would like to have up to date copies of some of the tables sent across the internet to our servers at our office. We would like to only copy a few of the tables because the bandwidth requirement to do log shipping of the entire database (our current solution) is too high. Also replication directly to our servers is out of the question as our servers are not accessible from the internet and management does not want to do replication (more on that later). One possible Idea we had is to do some form of replication on the tables we need to another database on the same server and do log shipping of that second smaller database but management is concerned that the clients have broken replication (it was between two servers on their internal network however) on us in the past and would like to stay away from it if possible. Any recommendations would be greatly appreciated. If using some form of replication is the only solution, I am not against replication, I just need compelling arguments to convince management to do it. This is to be set up on multiple sites that are running either Sql2005 or Sql2008 we will have both versions on our end to restore the data to so that is not a issue. Thank you.

  Read the article

• Intermittently uncommunicative subnets

  - by mhd

  Last week proved me a veritable Cassandra: I've always said that it's a bad idea to have only one firewall/router, without a backup or failover. And thus our Cisco PIX went haywire, refusing to route properly. And of course, the only one available here on short notice is me, and while I'm quite grounded in Linux, I'm really a developer not a sysadmin (the fact that this hit me on sysadmin appreciation day is a bit ironic). Anyway, this weekend I tried to hack up a temporary solution: I used an old server with enough NICs (two built-in, four on a card) to serve as a gateway and firewall. Due to some problems with the raid controller, I got only two router distros running, and between Untangle and Ebox I decided for the latter. Now everything is quite okay. I've got all the different subnets we've got here (all with separate switches) talking to each other and even to the internet (Cisco 2800 router, T1 lines). But from time to time (20-60 minute intervals), I get a total routing failure. Our main, office subnet can't talk to our server subnet and can't connect to the internet. This is not the end of a gradual slowdown, either everything's working perfectly or I get a total lack of communication for about two minutes each time. Now I'm a bit at wits end what to check. At least with the default EBox setup, nothing in /var/log shows anything weird and it doesn't exactly have lots of built-in monitoring tools. So I'm hoping someone here could give me some pointers about what to look out for. I did change the ethernet cable from the office switch to the firewall, with no results. I might change switches, although within the switch it seems to work ok enough. Edit: I'm not sure whether this is the sole cause of the problem, but after I noticed a few DHCP entries just before the last drop of connectivity, I tried to reproduce that. And alas, whenever I renew a DHCP connection, I can't access other subnets anymore. Running ISC DHCPD 3.0.6.

  Read the article

< Previous Page | 553 554 555 556 557 558 559 560 561 562 563 564  | Next Page >