Search Results

Search found 8384 results on 336 pages for 'lines'.

Page 56/336 | < Previous Page | 52 53 54 55 56 57 58 59 60 61 62 63  | Next Page >

• Trouble installing Ubuntu.

  - by CV13

  I have a blank 1TB hard drive that I have run ubuntu on before. I recently formatted it and am trying to reinstall Ubuntu 12.04 LTS on there. Using the Universal USB installer and the 64-bit iso file, I booted up my computer with only my 1TB hard drive connected. I go through the installation process normally, until I restart my computer at the end. Once restarted, I start to experience the problem deal with here. When I run it normally, it goes to a black screen with a blinking cursor. When I select the "Recovery Mode" option, a bunch of lines scroll across the screen, the last of which is "hostap_pci: Registered netdevice wifi0". It then stops there with a blinking cursor. When I follow the instructions on the page I linked to (replacing "quiet splash" with "nomodeset") and bunch of lines scroll through after I press Ctrl+x. The last line displayed is Adding 8386556k swap on /dev/sda5. Priority:-1 extents:1 across: 8386556k It then stops there with a blinking cursor. How do I fix this problem?

  Read the article

• Rendering a WPF Network Map/Graph layout - Manual? PathListBox? Something Else?

  - by Ben Von Handorf

  I'm writing code to present the user with a simplified network map. At any given time, the map is focused on a specific item... say a router or a server. Based on the focused item, other network entities are grouped into sets (i.e. subnets or domains) and then rendered around the focused item. Lines would represent connections and groups would be visually grouped inside a rectangle or ellipse. Panning and zooming are required features. An item can be selected to display more information in a "properties" style window. An item could also be double-clicked to re-focus the entire network map on that item. At that point, the entire map would be re-calculated. I am using MVVM without any framework, as of yet. Assume the logic for grouping items and determining what should be shown or not is all in place. I'm looking for the best way to approach the UI layout. So far, I'm aware of the following options: Use a canvas for layout (inside a ScrollViewer to handle the panning). Have my ViewModel make use of a Layout Manager type of class, which would handle assigning all the layout properties (Top, Left, etc.). Bind my set of display items to an ItemsControl and use Data Templates to handle the actual rendering. The drawbacks with this approach: Highly manual layout on my part. Lots of calculation. I have to handle item selection manually. Computation of connecting lines is manual. The Pros of this approach: I can draw additional lines between child subnets as appropriate (manually). Additional LayoutManagers could be added later to render the display differently. This could probably be wrapped up into some sort of a GraphLayout control to be re-used. Present the focused item at the center of the display and then use a PathListBox for layout of the additional items. Have my ViewModel expose a simple list of things to be drawn and bind them to the PathListBox. Override the ListBoxItem Template to also create a line geometry from the borders of the focused item (tricky) to the bound item. Use DataTemplates to handle the case where the item being bound is a subnet, in which case we would use another PathListBox in the template to display items inside the subnet. The drawbacks with this approach: Selected Item synchronization across multiple `PathListBox`es. Only one item on the whole graph can be selected at a time, but each child PathListBox maintains its own selection. Also, subnets cannot be selected, but would be selectable without additional work. Drawing the connecting lines is going to be a bit of trickery in the ListBoxItem template, since I need to know the correct side of the focused item to connect to. The pros of this approach: I get to stay out of the layout business, more. I'm looking for any advice or thoughts from others who have encountered similar issues or who have more WPF experience than I. I'm using WPF 4, so any new tricks are legal and encouraged.

  Read the article

• How to animate an non-closed path with CAShapeLayer?

  - by mystify

  On GitHub you can find an example for CAShapeLayer which animates an path. It animates a pentagon turning into a star. First: This works only in the iPhone simulator. OS 3.0 on the device shows serious bugs with this code. But I can't find anything wrong in there. However, I tried to animate an path which is not closed. To put it simply: A few straight lines. Is there anything special I must do to get this work properly on the device? - (void)loadView { UIView *appView = [[UIView alloc] initWithFrame:[[UIScreen mainScreen] bounds]]; appView.backgroundColor = [UIColor blackColor]; self.view = appView; [appView release]; rootLayer = [CALayer layer]; rootLayer.frame = self.view.bounds; [self.view.layer addSublayer:rootLayer]; //Pentagon Path pentagonPath = CGPathCreateMutable(); CGPathMoveToPoint(pentagonPath, nil, 10.0f, 270.0f); CGPathAddLineToPoint(pentagonPath, nil, 100.0f, 270.0f); CGPathAddLineToPoint(pentagonPath, nil, 110.0f, 270.0f); CGPathAddLineToPoint(pentagonPath, nil, 120.0f, 270.0f); CGPathAddLineToPoint(pentagonPath, nil, 130.0f, 270.0f); CGPathAddLineToPoint(pentagonPath, nil, 310.0f, 270.0f); //CGPathCloseSubpath(pentagonPath); //Star Path starPath = CGPathCreateMutable(); CGPathMoveToPoint(starPath, nil, 10.0f, 270.0f); CGPathAddLineToPoint(starPath, nil, 100.0f, 270.0f); CGPathAddLineToPoint(starPath, nil, 210.0f, 270.0f); CGPathAddLineToPoint(starPath, nil, 220.0f, 260.0f); CGPathAddLineToPoint(starPath, nil, 230.0f, 270.0f); CGPathAddLineToPoint(starPath, nil, 310.0f, 270.0f); //CGPathCloseSubpath(starPath); //Create Shape shapeLayer = [CAShapeLayer layer]; //shapeLayer.path = pentagonPath; UIColor *col = [UIColor colorWithWhite:0.9 alpha:1.0]; //shapeLayer.fillColor = col.CGColor; shapeLayer.strokeColor = col.CGColor; shapeLayer.lineWidth = 3.0f; // shapeLayer.contents = [UIImage imageNamed:@"test.png"]; shapeLayer.fillRule = kCAFillRuleEvenOdd; [rootLayer addSublayer:shapeLayer]; [self performSelector:@selector(startAnimation) withObject:nil afterDelay:1.0]; } -(void)startAnimation { CABasicAnimation *animation = [CABasicAnimation animationWithKeyPath:@"path"]; animation.duration = 2.0; animation.timingFunction = [CAMediaTimingFunction functionWithName:kCAMediaTimingFunctionEaseInEaseOut]; animation.repeatCount = 1e100f; animation.autoreverses = YES; animation.fromValue = (id)pentagonPath; animation.toValue = (id)starPath; [shapeLayer addAnimation:animation forKey:@"animatePath"]; } Note this lines, where I just make straight lines with a small peak which is animated: //Pentagon Path pentagonPath = CGPathCreateMutable(); CGPathMoveToPoint(pentagonPath, nil, 10.0f, 270.0f); CGPathAddLineToPoint(pentagonPath, nil, 100.0f, 270.0f); CGPathAddLineToPoint(pentagonPath, nil, 110.0f, 270.0f); CGPathAddLineToPoint(pentagonPath, nil, 120.0f, 270.0f); CGPathAddLineToPoint(pentagonPath, nil, 130.0f, 270.0f); CGPathAddLineToPoint(pentagonPath, nil, 310.0f, 270.0f); //CGPathCloseSubpath(pentagonPath); //Star Path starPath = CGPathCreateMutable(); CGPathMoveToPoint(starPath, nil, 10.0f, 270.0f); CGPathAddLineToPoint(starPath, nil, 100.0f, 270.0f); CGPathAddLineToPoint(starPath, nil, 210.0f, 270.0f); CGPathAddLineToPoint(starPath, nil, 220.0f, 260.0f); CGPathAddLineToPoint(starPath, nil, 230.0f, 270.0f); CGPathAddLineToPoint(starPath, nil, 310.0f, 270.0f); I don't want a closed and filled path, but only simple lines with some color and thickness. The nasty thing on the device is, that the first point seems to move towards the right side of the screen for no reason. On the simulator though, it works perfectly fine. Maybe something is wrong with this setup?

  Read the article

• File Fix-it codegolf (GCJ 2010 1B-A)

  - by KirarinSnow

  Last year (2009), the Google Code Jam featured an interesting problem as the first problem in Round 1B: Decision Tree As the problem seemed tailored for Lisp-like languages, we spontaneously had an exciting codegolf here on SO, in which a few languages managed to solve the problem in fewer characters than any Lisp variety, using quite a number of different techniques. This year's Round 1B Problem A (File Fix-it) also seems tailored for a particular family of languages, Unix shell scripts. So continuing the "1B-A tradition" would be appropriate. :p But which language will end up with the shortest code? Let us codegolf and see! Problem description (adapted from official page): You are given T test cases. Each test case contains N lines that list the full path of all directories currently existing on your computer. For example: /home/awesome /home/awesome/wheeeeeee /home/awesome/wheeeeeee/codegolfrocks /home/thecakeisalie Next, you are given M lines that list the full path of directories you would like to create. They are in the same format as the previous examples. You can create a directory using the mkdir command, but you can only do so if the parent directory already exists. For example, to create the directories /pyonpyon/fumufumu/yeahyeah and /pyonpyon/fumufumu/yeahyeahyeah, you would need to use mkdir four times: mkdir /pyonpyon mkdir /pyonpyon/fumufumu mkdir /pyonpyon/fumufumu/yeahyeah mkdir /pyonpyon/fumufumu/yeahyeahyeah For each test case, return the number of times you have to call mkdir to create all the directories you would like to create. Input Input consists of a text file whose first line contains the integer T, the number of test cases. The rest of the file contains the test cases. Each test case begins with a line containing the integers N and M, separated by a space. The next N lines contain the path of each directory currently existing on your computer (not including the root directory /). This is a concatenation of one or more non-empty lowercase alphanumeric strings, each preceded by a single /. The following M lines contain the path of each directory you would like to create. Output For each case, print one line containing Case #X: Y, where X is the case number and Y is the solution. Limits 1 = T = 100. 0 = N = 100. 1 = M = 100. Each path contains at most 100 characters. Every path appears only once in the list of directories already on your computer, or in the list of desired directories. However, a path may appear on both lists, as in example case #3 below. If a directory is in the list of directories already on your computer, its parent directory will also be listed, with the exception of the root directory /. The input file is at most 100,000 bytes long. Example Larger sample test cases may be downloaded here. Input: 3 0 2 /home/sparkle/pyon /home/sparkle/cakes 1 3 /z /z/y /z/x /y/y 2 1 /moo /moo/wheeeee /moo Output: Case #1: 4 Case #2: 4 Case #3: 0 Code Golf Please post your shortest code in any language that solves this problem. Input and output may be handled via stdin and stdout or by other files of your choice. Please include a disclaimer if your code has the potential to modify or delete existing files when executed. Winner will be the shortest solution (by byte count) in a language with an implementation existing prior to the start of Round 1B 2010.

  Read the article

• Python - Bitmap won't draw/display

  - by Wallter

  I have been working on this project for some time now - it was originally supposed to be a test to see if, using wxPython, I could build a button 'from scratch.' From scratch means: that i would have full control over all the aspects of the button (i.e. controlling the BMP's that are displayed... what the event handlers did... etc.) I have run into several problems (as this is my first major python project.) Now, when the all the code is working for the life of me I can't get an image to display. Basic code - not working dc = wx.BufferedPaintDC(self) dc.SetFont(self.GetFont()) dc.SetBackground(wx.Brush(self.GetBackgroundColour())) dc.Clear() dc.DrawBitmap(wx.Bitmap("/home/wallter/Desktop/Mouseover.bmp"), 100, 100) self.Refresh() self.Update() Full Main.py import wx from Custom_Button import Custom_Button from wxPython.wx import * ID_ABOUT = 101 ID_EXIT = 102 class MyFrame(wx.Frame): def __init__(self, parent, ID, title): wxFrame.__init__(self, parent, ID, title, wxDefaultPosition, wxSize(400, 400)) self.CreateStatusBar() self.SetStatusText("Program testing custom button overlays") menu = wxMenu() menu.Append(ID_ABOUT, "&About", "More information about this program") menu.AppendSeparator() menu.Append(ID_EXIT, "E&xit", "Terminate the program") menuBar = wxMenuBar() menuBar.Append(menu, "&File"); self.SetMenuBar(menuBar) # The call for the 'Experiential button' self.Button1 = Custom_Button(parent, -1, wx.Point(100, 100), wx.Bitmap("/home/wallter/Desktop/Mouseover.bmp"), wx.Bitmap("/home/wallter/Desktop/Normal.bmp"), wx.Bitmap("/home/wallter/Desktop/Click.bmp")) # The following three lines of code are in place to try to get the # Button1 to display (trying to trigger the Paint event (the _onPaint.) # Because that is where the 'draw' functions are. self.Button1.Show(true) self.Refresh() self.Update() # Because the Above three lines of code did not work, I added the # following four lines to trigger the 'draw' functions to test if the # '_onPaint' method actually worked. # These lines do not work. dc = wx.BufferedPaintDC(self) dc.SetFont(self.GetFont()) dc.SetBackground(wx.Brush(self.GetBackgroundColour())) dc.DrawBitmap(wx.Bitmap("/home/wallter/Desktop/Mouseover.bmp"), 100, 100) EVT_MENU(self, ID_ABOUT, self.OnAbout) EVT_MENU(self, ID_EXIT, self.TimeToQuit) def OnAbout(self, event): dlg = wxMessageDialog(self, "Testing the functions of custom " "buttons using pyDev and wxPython", "About", wxOK | wxICON_INFORMATION) dlg.ShowModal() dlg.Destroy() def TimeToQuit(self, event): self.Close(true) class MyApp(wx.App): def OnInit(self): frame = MyFrame(NULL, -1, "wxPython | Buttons") frame.Show(true) self.SetTopWindow(frame) return true app = MyApp(0) app.MainLoop() Full CustomButton.py import wx from wxPython.wx import * class Custom_Button(wx.PyControl): def __init__(self, parent, id, Pos, Over_BMP, Norm_BMP, Push_BMP, **kwargs): wx.PyControl.__init__(self,parent, id, **kwargs) self.Bind(wx.EVT_LEFT_DOWN, self._onMouseDown) self.Bind(wx.EVT_LEFT_UP, self._onMouseUp) self.Bind(wx.EVT_LEAVE_WINDOW, self._onMouseLeave) self.Bind(wx.EVT_ENTER_WINDOW, self._onMouseEnter) self.Bind(wx.EVT_ERASE_BACKGROUND,self._onEraseBackground) self.Bind(wx.EVT_PAINT,self._onPaint) self.pos = Pos self.Over_bmp = Over_BMP self.Norm_bmp = Norm_BMP self.Push_bmp = Push_BMP self._mouseIn = False self._mouseDown = False def _onMouseEnter(self, event): self._mouseIn = True def _onMouseLeave(self, event): self._mouseIn = False def _onMouseDown(self, event): self._mouseDown = True def _onMouseUp(self, event): self._mouseDown = False self.sendButtonEvent() def sendButtonEvent(self): event = wx.CommandEvent(wx.wxEVT_COMMAND_BUTTON_CLICKED, self.GetId()) event.SetInt(0) event.SetEventObject(self) self.GetEventHandler().ProcessEvent(event) def _onEraseBackground(self,event): # reduce flicker pass def Iz(self): dc = wx.BufferedPaintDC(self) dc.DrawBitmap(self.Norm_bmp, 100, 100) def _onPaint(self, event): # The printing functions, they should work... but don't. dc = wx.BufferedPaintDC(self) dc.SetFont(self.GetFont()) dc.SetBackground(wx.Brush(self.GetBackgroundColour())) dc.Clear() dc.DrawBitmap(self.Norm_bmp) # This never printed... I don't know if that means if the EVT # is triggering or what. print '_onPaint' # draw whatever you want to draw # draw glossy bitmaps e.g. dc.DrawBitmap if self._mouseIn: # If the Mouse is over the button dc.DrawBitmap(self.Over_bmp, self.pos) else: # Since the mouse isn't over it Print the normal one # This is adding on the above code to draw the bmp # in an attempt to get the bmp to display; to no avail. dc.DrawBitmap(self.Norm_bmp, self.pos) if self._mouseDown: # If the Mouse clicks the button dc.DrawBitmap(self.Push_bmp, self.pos) This code won't work? I get no BMP displayed why? How do i get one? I've gotten the staticBitmap(...) to display one, but it won't move, resize, or anything for that matter... - it's only in the top left corner of the frame? Note: the frame is 400pxl X 400pxl - and the "/home/wallter/Desktop/Mouseover.bmp"

  Read the article

• Keyboard for programming

  - by exhuma

  This may seem a bit a tangential topic. It's not directly related to actual code, but is important for our line of work nevertheless. Over the years, I've switched keyboards a few times. All of them had slightly different key layouts. And I'm not talking about the language/locale layout, but the physical layout! Why not the locale layout? Well, quite frankly, that's easy to change via software. I personally have a German keyboard but have it set to the UK layout. Why? It's quite hard to find different layouts in the shops where I live. Even ordering is not always easy in the shops. So that leaves me with Internet shops. But I prefer to "test" my keyboards before buying. The most notable changes are: Mangled "Home Key Block" I've seen this first on a Logitech keyboard, but it may have originated elsewhere. Shape of the "Enter" key I've seen three different cases so far: Two lines high, wider at the top Two lines high, wider at the bottom One line high Shape of the Backspace button I've seen two types so far: One "character" wide Two "characters" wide OS Keys For Macs, you have the Option and Command buttons, for Windows you have the Windows and Context Menu buttons. Cherry even produced a Linux keyboard once (unfortunately I cannot find many details except news results). I assume a dedicated Linux keyboard would sport a Compose key and had the SysRq always labelled as well (note that some standard layouts do this already). Obviously... .. all these differences entail that some keys have to be moved around the board a lot. Which means, if you are used to one and have to work on another one, you happen to hit the wrong keys quite often. As it happens, this is much more annoying for programmers as it is for people who write texts. Mainly because the keys which are moved around are special character keys, often used in programming. Often these hardware layouts depend also indirectly on where you buy the keyboards. Honestly, I haven't seen a keyboard with a one-line "Enter" key in Germany, nor Luxembourg. I may just have missed it but that's how it looks to me at least. A survey I've seen some attempts at surveys in the style "which keyboard is best for programming". But they all - in my opinion - are not using comparable sets. So I was wondering if it was possible to concoct a survey taking the above criteria into account. But ignoring key dimensions that one would be a bit overkill I guess ;) From what I can see there are the following types of physical layout: Backspace: 2-characters wide Enter: 2-Lines, wider top Backspace: 2-characters wide Enter: 1-Line Backspace: 1-character wide Enter: 2-Lines, wider bottom Then there are the other possible permutations (home-key block, os-keys), which in total makes for quite a large list of categories. Now, I wonder... Would anyone be interested in such a survey? I personally would. Because I am looking for the perfect fit for me. If yes, then I could really use the help of anyone here to propose some models to include in the survey. Once I have some models for each category (I'd say at least 3 per category) I could go ahead and write up a survey, put it on-line and let the it collect data for a while. What do you think?

  Read the article

• Pulling record from mySQL database only working for userid and not email

  - by user2908467

  This function works because I search by userid: private void showList_Click(object sender, EventArgs e) { int id = 0; for (int i = 0; i <= sqlClient.Count("UserList"); i++) { Dictionary<string, string> dik = sqlClient.Select("UserList", "userid = " + id); var lines = dik.Select(kv => kv.Key + ": " + kv.Value.ToString()); userList.AppendText(string.Join(Environment.NewLine, lines)); userList.AppendText(Environment.NewLine); userList.AppendText("--------------------------------------"); id++; } } This function does not work because I search by email: private void login_Click(object sender, EventArgs e) { string email = lemail.Text; Dictionary<string, string> dik = sqlClient.Select("UserList", "firstname = " + email); var lines = dik.Select(kv => kv.Key + ": " + kv.Value.ToString()); logged.AppendText(string.Join(Environment.NewLine, lines)); } This is the error message I receive when I click on the login button: You have an error in your SQL syntax; check the manual that corresponds to your MySQL server version for the right syntax to use near '@aol.com' at line 1 The email I searched for in the database was "[email protected]" without quotes. I'm lead to believe by the error message the @ sign is causing conflict as I know it is a special character but I am having a hard time figuring out what phrase to search for to help me. Also, here is the function that is being called: public Dictionary<string, string> Select(string table, string WHERE) { //This methods selects from the database, it retrieves data from it. //You must make a dictionary to use this since it both saves the column //and the value. i.e. "age" and "33" so you can easily search for values. //Example: SELECT * FROM names WHERE name='John Smith' // This example would retrieve all data about the entry with the name "John Smith" //Code = Dictionary<string, string> myDictionary = Select("names", "name='John Smith'"); //This code creates a dictionary and fills it with info from the database. string query = "SELECT * FROM " + table + " WHERE " + WHERE + ""; Dictionary<string, string> selectResult = new Dictionary<string, string>(); if (this.Open()) { MySqlCommand cmd = new MySqlCommand(query, conn); MySqlDataReader dataReader = cmd.ExecuteReader(); try { while (dataReader.Read()) { for (int i = 0; i < dataReader.FieldCount; i++) { selectResult.Add(dataReader.GetName(i).ToString(), dataReader.GetValue(i).ToString()); } } dataReader.Close(); } catch { } this.Close(); return selectResult; } else { return selectResult; } } My database table is called "UserList" The fields in order are as follows: userid, email, password, lastname, firstname Any help would be greatly appreciated. This site is amazing!

  Read the article

• onDraw() triggered but results don't show

  - by Don

  I have the following routine in a subclass of view: It calculates an array of points that make up a line, then erases the previous lines, then draws the new lines (impact refers to the width in pixels drawn with multiple lines). The line is your basic bell curve, squeezed or stretched by variance and x-factor. Unfortunately, nothing shows on the screen. A previous version with drawPoint() and no array worked, and I've verified the array contents are being loaded correctly, and I can see that my onDraw() is being triggered. Any ideas why it might not be drawn? Thanks in advance! protected void drawNewLine( int maxx, int maxy, Canvas canvas, int impact, double variance, double xFactor, int color) { // impact = 2 to 8; xFactor between 4 and 20; variance between 0.2 and 5 double x = 0; double y = 0; int cx = maxx / 2; int cy = maxy / 2; int mu = cx; int index = 0; points[maxx<<1][1] = points[maxx<<1][0]; for (x = 0; x < maxx; x++) { points[index][1] = points[index][0]; points[index][0] = (float) x; Log.i(DEBUG_TAG, "x: " + x); index++; double root = 1.0 / (Math.sqrt(2 * Math.PI * variance)); double exponent = -1.0 * (Math.pow(((x - mu)/maxx*xFactor), 2) / (2 * variance)); double ePow = Math.exp(exponent); y = Math.round(cy * root * ePow); points[index][1] = points[index][0]; points[index][0] = (float) (maxy - y - OFFSET); index++; } points[maxx<<1][0] = (float) impact; for (int line = 0; line < points[maxx<<1][1]; line++) { for (int pt = 0; pt < (maxx<<1); pt++) { pointsToPaint[pt] = points[pt][1]; } for (int skip = 1; skip < (maxx<<1); skip = skip + 2) pointsToPaint[skip] = pointsToPaint[skip] + line; myLinePaint.setColor(Color.BLACK); canvas.drawLines(pointsToPaint, bLinePaint); // draw over old lines w/blk } for (int line = 0; line < points[maxx<<1][0]; line++) { for (int pt = 0; pt < maxx<<1; pt++) { pointsToPaint[pt] = points[pt][0]; } for (int skip = 1; skip < maxx<<1; skip = skip + 2) pointsToPaint[skip] = pointsToPaint[skip] + line; myLinePaint.setColor(color); canvas.drawLines(pointsToPaint, myLinePaint); / new color } } update: Replaced the drawLines() with drawPoint() in loop, still no joy for (int p = 0; p<pointsToPaint.length; p = p + 2) { Log.i(DEBUG_TAG, "x " + pointsToPaint[p] + " y " + pointsToPaint[p+1]); canvas.drawPoint(pointsToPaint[p], pointsToPaint[p+1], myLinePaint); } /// canvas.drawLines(pointsToPaint, myLinePaint);

  Read the article

• Web Application Problems (web.config errors) HTTP 500.19 with IIS7.5 and ASP.NET v2

  - by Django Reinhardt

  This is driving the whole team crazy. There must be some simple mis-configured part of IIS or our Web Server, but every time we try to run out ASP.NET Web Application on IIS 7.5 we get the following error... Here's the error in full: HTTP Error 500.19 - Internal Server Error The requested page cannot be accessed because the related configuration data for the page is invalid. `Detailed Error Information` Module IIS Web Core Notification Unknown Handler Not yet determined Error Code 0x8007000d Config Error Config File \\?\E:\wwwroot\web.config Requested URL http://localhost:80/Default.aspx Physical Path Logon Method Not yet determined Logon User Not yet determined Config Source -1: 0: The machine is running Windows Server 2008 R2. We're developing our Web Application using Visual Studio 2008. According to Microsoft the code 8007000d means there's a syntax error in our web.config -- except the project builds and runs fine locally. Looking at the web.config in XML Notepad doesn't bring up any syntax errors, either. I'm assuming it must be some sort of poor configuration on my part...? Does anyone know where I might find further information about the error? Nothing is showing in EventViewer, either :( Not sure what else would be helpful to mention... Assistance is greatly appreciated. Thanks! UPDATES! - POSTED WEB.CONFIG BELOW Ok, since I posted the original question above, I've tracked down the precise lines in the web.config that were causing the error. Here are the lines (they appear between <System.webServer> tags)... <httpHandlers> <remove verb="*" path="*.asmx"/> <add verb="*" path="*.asmx" validate="false" type="System.Web.Script.Services.ScriptHandlerFactory, System.Web.Extensions, Version=1.0.61025.0, Culture=neutral, PublicKeyToken=f2cb5667dc123a56"/> </httpHandlers> Note: If I delete the lines between the <httpHandlers> I STILL get the error. I literally have to delete <httpHandlers> (and the lines inbetween) to stop getting the above error. Once I've done this I get a new 500.19 error, however. Thankfully, this time IIS actually tells me which bit of the web.config is causing a problem... <handlers> <remove name="WebServiceHandlerFactory-Integrated"/> <add verb="*" path="*.asmx" validate="false" type="System.Web.Script.Services.ScriptHandlerFactory,System.Web.Extensions, Version=1.0.61025.0, Culture=neutral, PublicKeyToken=f2cb5667dc123a56"/> <add name="ScriptHandlerFactoryAppServices" verb="*" path="*_AppService.axd" preCondition="integratedMode" type="System.Web.Script.Services.ScriptHandlerFactory, System.Web.Extensions, Version=1.0.61025.0, Culture=neutral, PublicKeyToken=f2cb5667dc123a56"/> <add name="ScriptResource" preCondition="integratedMode" verb="GET,HEAD" path="ScriptResource.axd" type="System.Web.Handlers.ScriptResourceHandler, System.Web.Extensions, Version=1.0.61025.0, Culture=neutral, PublicKeyToken=f2cb5667dc123a56"/> </handlers> Looking at these lines it's clear the problem has migrated further within the same <system.webServer> tag to the <handlers> tag. The new error is also more explicit and specifically complains that it doesn't recognize the attribute "validate" (as seen on the third line above). Removing this attribute then makes it complain that the same line doesn't have the required "name" attribute. Adding this attribute then brings up ASP.NET error... Could not load file or assembly 'System.web.Extensions, Version=1.0.61025.0, Culture=neutral, PublicKeyToken=f2cb5667dc123a56' or one of its dependencies. The system cannot find the file specified. Obviously I think these new errors have just arisen from me deleting the <httpHandlers> tags in the first place -- they're obviously needed by the application -- so the question remains: Why would these tags kick up an error in IIS in the first place??? Do I need to install something to IIS to make it work with them? Thanks again for any help. WEB.CONFIG Here's the troublesome bits of our web.Config... I hope this helps someone find our problem! <system.Web> <!-- stuff cut out --> <httpHandlers> <remove verb="*" path="*.asmx"/> <add verb="*" path="*.asmx" validate="false" type="System.Web.Script.Services.ScriptHandlerFactory, System.Web.Extensions, Version=1.0.61025.0, Culture=neutral, PublicKeyToken=f2cb5667dc123a56"/> <add verb="*" path="*_AppService.axd" validate="false" type="System.Web.Script.Services.ScriptHandlerFactory, System.Web.Extensions, Version=1.0.61025.0, Culture=neutral, PublicKeyToken=f2cb5667dc123a56"/> <add verb="GET,HEAD" path="ScriptResource.axd" type="System.Web.Handlers.ScriptResourceHandler, System.Web.Extensions, Version=1.0.61025.0, Culture=neutral, PublicKeyToken=f2cb5667dc123a56" validate="false"/> </httpHandlers> <httpModules> <add name="ScriptModule" type="System.Web.Handlers.ScriptModule, System.Web.Extensions, Version=1.0.61025.0, Culture=neutral, PublicKeyToken=f2cb5667dc123a56"/> </httpModules> </system.web> <system.webServer> <validation validateIntegratedModeConfiguration="false"/> <modules> <add name="ScriptModule" preCondition="integratedMode" type="System.Web.Handlers.ScriptModule, System.Web.Extensions, Version=1.0.61025.0, Culture=neutral, PublicKeyToken=f2cb5667dc123a56"/> </modules> <remove verb="*" path="*.asmx"/> <add verb="*" path="*.asmx" validate="false" type="System.Web.Script.Services.ScriptHandlerFactory, System.Web.Extensions, Version=1.0.61025.0, Culture=neutral, PublicKeyToken=f2cb5667dc123a56"/> <handlers> <remove name="WebServiceHandlerFactory-Integrated"/> <add verb="*" path="*.asmx" validate="false" type="System.Web.Script.Services.ScriptHandlerFactory,System.Web.Extensions, Version=1.0.61025.0, Culture=neutral, PublicKeyToken=f2cb5667dc123a56"/> <add name="ScriptHandlerFactoryAppServices" verb="*" path="*_AppService.axd" preCondition="integratedMode" type="System.Web.Script.Services.ScriptHandlerFactory, System.Web.Extensions, Version=1.0.61025.0, Culture=neutral, PublicKeyToken=f2cb5667dc123a56"/> <add name="ScriptResource" preCondition="integratedMode" verb="GET,HEAD" path="ScriptResource.axd" type="System.Web.Handlers.ScriptResourceHandler, System.Web.Extensions, Version=1.0.61025.0, Culture=neutral, PublicKeyToken=f2cb5667dc123a56"/> </handlers> </system.webServer>

  Read the article

• F# - Facebook Hacker Cup - Double Squares

  - by Jacob

  I'm working on strengthening my F#-fu and decided to tackle the Facebook Hacker Cup Double Squares problem. I'm having some problems with the run-time and was wondering if anyone could help me figure out why it is so much slower than my C# equivalent. There's a good description from another post; Source: Facebook Hacker Cup Qualification Round 2011 A double-square number is an integer X which can be expressed as the sum of two perfect squares. For example, 10 is a double-square because 10 = 3^2 + 1^2. Given X, how can we determine the number of ways in which it can be written as the sum of two squares? For example, 10 can only be written as 3^2 + 1^2 (we don't count 1^2 + 3^2 as being different). On the other hand, 25 can be written as 5^2 + 0^2 or as 4^2 + 3^2. You need to solve this problem for 0 = X = 2,147,483,647. Examples: 10 = 1 25 = 2 3 = 0 0 = 1 1 = 1 My basic strategy (which I'm open to critique on) is to; Create a dictionary (for memoize) of the input numbers initialzed to 0 Get the largest number (LN) and pass it to count/memo function Get the LN square root as int Calculate squares for all numbers 0 to LN and store in dict Sum squares for non repeat combinations of numbers from 0 to LN If sum is in memo dict, add 1 to memo Finally, output the counts of the original numbers. Here is the F# code (See code changes at bottom) I've written that I believe corresponds to this strategy (Runtime: ~8:10); open System open System.Collections.Generic open System.IO /// Get a sequence of values let rec range min max = seq { for num in [min .. max] do yield num } /// Get a sequence starting from 0 and going to max let rec zeroRange max = range 0 max /// Find the maximum number in a list with a starting accumulator (acc) let rec maxNum acc = function | [] -> acc | p::tail when p > acc -> maxNum p tail | p::tail -> maxNum acc tail /// A helper for finding max that sets the accumulator to 0 let rec findMax nums = maxNum 0 nums /// Build a collection of combinations; ie [1,2,3] = (1,1), (1,2), (1,3), (2,2), (2,3), (3,3) let rec combos range = seq { let count = ref 0 for inner in range do for outer in Seq.skip !count range do yield (inner, outer) count := !count + 1 } let rec squares nums = let dict = new Dictionary<int, int>() for s in nums do dict.[s] <- (s * s) dict /// Counts the number of possible double squares for a given number and keeps track of other counts that are provided in the memo dict. let rec countDoubleSquares (num: int) (memo: Dictionary<int, int>) = // The highest relevent square is the square root because it squared plus 0 squared is the top most possibility let maxSquare = System.Math.Sqrt((float)num) // Our relevant squares are 0 to the highest possible square; note the cast to int which shouldn't hurt. let relSquares = range 0 ((int)maxSquare) // calculate the squares up front; let calcSquares = squares relSquares // Build up our square combinations; ie [1,2,3] = (1,1), (1,2), (1,3), (2,2), (2,3), (3,3) for (sq1, sq2) in combos relSquares do let v = calcSquares.[sq1] + calcSquares.[sq2] // Memoize our relevant results if memo.ContainsKey(v) then memo.[v] <- memo.[v] + 1 // return our count for the num passed in memo.[num] // Read our numbers from file. //let lines = File.ReadAllLines("test2.txt") //let nums = [ for line in Seq.skip 1 lines -> Int32.Parse(line) ] // Optionally, read them from straight array let nums = [1740798996; 1257431873; 2147483643; 602519112; 858320077; 1048039120; 415485223; 874566596; 1022907856; 65; 421330820; 1041493518; 5; 1328649093; 1941554117; 4225; 2082925; 0; 1; 3] // Initialize our memoize dictionary let memo = new Dictionary<int, int>() for num in nums do memo.[num] <- 0 // Get the largest number in our set, all other numbers will be memoized along the way let maxN = findMax nums // Do the memoize let maxCount = countDoubleSquares maxN memo // Output our results. for num in nums do printfn "%i" memo.[num] // Have a little pause for when we debug let line = Console.Read() And here is my version in C# (Runtime: ~1:40: using System; using System.Collections.Generic; using System.Diagnostics; using System.IO; using System.Linq; using System.Text; namespace FBHack_DoubleSquares { public class TestInput { public int NumCases { get; set; } public List<int> Nums { get; set; } public TestInput() { Nums = new List<int>(); } public int MaxNum() { return Nums.Max(); } } class Program { static void Main(string[] args) { // Read input from file. //TestInput input = ReadTestInput("live.txt"); // As example, load straight. TestInput input = new TestInput { NumCases = 20, Nums = new List<int> { 1740798996, 1257431873, 2147483643, 602519112, 858320077, 1048039120, 415485223, 874566596, 1022907856, 65, 421330820, 1041493518, 5, 1328649093, 1941554117, 4225, 2082925, 0, 1, 3, } }; var maxNum = input.MaxNum(); Dictionary<int, int> memo = new Dictionary<int, int>(); foreach (var num in input.Nums) { if (!memo.ContainsKey(num)) memo.Add(num, 0); } DoMemoize(maxNum, memo); StringBuilder sb = new StringBuilder(); foreach (var num in input.Nums) { //Console.WriteLine(memo[num]); sb.AppendLine(memo[num].ToString()); } Console.Write(sb.ToString()); var blah = Console.Read(); //File.WriteAllText("out.txt", sb.ToString()); } private static int DoMemoize(int num, Dictionary<int, int> memo) { var highSquare = (int)Math.Floor(Math.Sqrt(num)); var squares = CreateSquareLookup(highSquare); var relSquares = squares.Keys.ToList(); Debug.WriteLine("Starting - " + num.ToString()); Debug.WriteLine("RelSquares.Count = {0}", relSquares.Count); int sum = 0; var index = 0; foreach (var square in relSquares) { foreach (var inner in relSquares.Skip(index)) { sum = squares[square] + squares[inner]; if (memo.ContainsKey(sum)) memo[sum]++; } index++; } if (memo.ContainsKey(num)) return memo[num]; return 0; } private static TestInput ReadTestInput(string fileName) { var lines = File.ReadAllLines(fileName); var input = new TestInput(); input.NumCases = int.Parse(lines[0]); foreach (var lin in lines.Skip(1)) { input.Nums.Add(int.Parse(lin)); } return input; } public static Dictionary<int, int> CreateSquareLookup(int maxNum) { var dict = new Dictionary<int, int>(); int square; foreach (var num in Enumerable.Range(0, maxNum)) { square = num * num; dict[num] = square; } return dict; } } } Thanks for taking a look. UPDATE Changing the combos function slightly will result in a pretty big performance boost (from 8 min to 3:45): /// Old and Busted... let rec combosOld range = seq { let rangeCache = Seq.cache range let count = ref 0 for inner in rangeCache do for outer in Seq.skip !count rangeCache do yield (inner, outer) count := !count + 1 } /// The New Hotness... let rec combos maxNum = seq { for i in 0..maxNum do for j in i..maxNum do yield i,j }

  Read the article

• Fixing up Visual Studio&rsquo;s gitignore , using IFix

  - by terje

  Originally posted on: http://geekswithblogs.net/terje/archive/2014/06/13/fixing-up-visual-studiorsquos-gitignore--using-ifix.aspxDownload tool Is there anything wrong with the built-in Visual Studio gitignore ???? Yes, there is !  First, some background: When you set up a git repo, it should be small and not contain anything not really needed.  One thing you should not have in your git repo is binary files. These binary files may come from two sources, one is the output files, in the bin and obj folders.  If you have a  gitignore file present, which you should always have (!!), these folders are excluded by the standard included file (the one included when you choose Team Explorer/Settings/GitIgnore – Add.) The other source are the packages folder coming from your NuGet setup.  You do use NuGet, right ?  Of course you do !  But, that gitignore file doesn’t have any exclude clause for those folders.  You have to add that manually.  (It will very probably be included in some upcoming update or release).  This is one thing that is missing from the built-in gitignore. To add those few lines is a no-brainer, you just include this: # NuGet Packages packages/* *.nupkg # Enable "build/" folder in the NuGet Packages folder since # NuGet packages use it for MSBuild targets. # This line needs to be after the ignore of the build folder # (and the packages folder if the line above has been uncommented) !packages/build/ Now, if you are like me, and you probably are, you add git repo’s faster than you can code, and you end up with a bunch of repo’s, and then start to wonder: Did I fix up those gitignore files, or did I forget it? The next thing you learn, for example by reading this blog post, is that the “standard” latest Visual Studio gitignore file exist at https://github.com/github/gitignore, and you locate it under the file name VisualStudio.gitignore.  Here you will find all the new stuff, for example, the exclusion of the roslyn ide folders was commited on May 24th.  So, you think, all is well, Visual Studio will use this file …..     I am very sorry, it won’t. Visual Studio comes with a gitignore file that is baked into the release, and that is by this time “very old”.  The one at github is the latest.  The included gitignore miss the exclusion of the nuget packages folder, it also miss a lot of new stuff, like the Roslyn stuff. So, how do you fix this ?  … note .. while we wait for the next version… You can manually update it for every single repo you create, which works, but it does get boring after a few times, doesn’t it ? IFix Enter IFix ,  install it from here. IFix is a command line utility (and the installer adds it to the system path, you might need to reboot), and one of the commands is gitignore If you run it from a directory, it will check and optionally fix all gitignores in all git repo’s in that folder or below.  So, start up by running it from your C:/<user>/source/repos folder. To run it in check mode – which will not change anything, just do a check: IFix  gitignore --check What it will do is to check if the gitignore file is present, and if it is, check if the packages folder has been excluded.  If you want to see those that are ok, add the --verbose command too.  The result may look like this: Fixing missing packages Let us fix a single repo by adding the missing packages structure,  using IFix --fix We first check, then fix, then check again to verify that the gitignore is correct, and that the “packages/” part has been added. If we open up the .gitignore, we see that the block shown below has been added to the end of the .gitignore file.   Comparing and fixing with latest standard Visual Studio gitignore (from github) Now, this tells you if you miss the nuget packages folder, but what about the latest gitignore from github ? You can check for this too, just add the option –merge (why this is named so will be clear later down) So, IFix gitignore --check –merge The result may come out like this  (sorry no colors, not got that far yet here): As you can see, one repo has the latest gitignore (test1), the others are missing either 57 or 150 lines.  IFix has three ways to fix this: --add --merge --replace The options work as follows: Add:  Used to add standard gitignore in the cases where a .gitignore file is missing, and only that, that means it won’t touch other existing gitignores. Merge: Used to merge in the missing lines from the standard into the gitignore file.  If gitignore file is missing, the whole standard will be added. Replace: Used to force a complete replacement of the existing gitignore with the standard one. The Add and Replace options can be used without Fix, which means they will actually do the action. If you combine with --check it will otherwise not touch any files, just do a verification.  So a Merge Check will  tell you if there is any difference between the local gitignore and the standard gitignore, a Compare in effect. When you do a Fix Merge it will combine the local gitignore with the standard, and add what is missing to the end of the local gitignore. It may mean some things may be doubled up if they are spelled a bit differently.  You might also see some extra comments added, but they do no harm. Init new repo with standard gitignore One cool thing is that with a new repo, or a repo that is missing its gitignore, you can grab the latest standard just by using either the Add or the Replace command, both will in effect do the same in this case. So, IFix gitignore --add will add it in, as in the complete example below, where we set up a new git repo and add in the latest standard gitignore: Notes The project is open sourced at github, and you can also report issues there.

  Read the article

• The Oracle Graduate Experience...A Graduates Perspective by Angelie Tierney

  - by david.talamelli

  [Note: Angelie has just recently joined Oracle in Australia in our 2011 Graduate Program. Last week I shared my thoughts on our 2011 Graduate Program, this week Angelie took some time to share her thoughts of our Graduate Program. The notes below are Angelie's overview from her experience with us starting with our first contact last year - David Talamelli] How does the 1 year program work? It consists of 3 weeks of training, followed by 2 rotations in 2 different Lines of Business (LoB's). The first rotation goes for 4 months, while your 2nd rotation goes for 7, when you are placed into your final LoB for the program. The interview process: After sorting through the many advertised graduate jobs, submitting so many resumes and studying at the same time, it can all be pretty stressful. Then there is the interview process. David called me on a Sunday afternoon and I spoke to him for about 30 minutes in a mini sort of phone interview. I was worried that working at Oracle would require extensive technical experience, but David stressed that even the less technical, and more business-minded person could, and did, work at Oracle. I was then asked if I would like to attend a group interview in the next weeks, to which I said of course! The first interview was a day long, consisting of a brief introduction, a group interview where we worked on a business plan with a group of other potential graduates and were marked by 3 Oracle employees, on our ability to work together and presentation. After lunch, we then had a short individual interview each, and that was the end of the first round. I received a call a few weeks later, and was asked to come into a second interview, at which I also jumped at the opportunity. This was an interview based purely on your individual abilities and would help to determine which Line of Business you would go to, should you land a graduate position. So how did I cope throughout the interview stages? I believe the best tool to prepare for the interview, was to research Oracle and its culture and to see if I thought I could fit into that. I personally found out about Oracle, its partners as well as competitors and along the way, even found out about their part (or Larry Ellison's specifically) in the Iron Man 2 movie. Armed with some Oracle information and lots of enthusiasm, I approached the Oracle Graduate Interview process. Why did I apply for an Oracle graduate position? I studied a Bachelor of Business/Bachelor of Science in IT, and wanted to be able to use both my degrees, while have the ability to work internationally in the future. Coming straight from university, I wasn't sure exactly what I wanted to do in terms of my career. With the program, you are rotated across various lines of business, to not only expose you to different parts of the business, but to also help you to figure out what you want to achieve out of your career. As a result, I thought Oracle was the perfect fit. So what can an Oracle ANZ Graduate expect? First things first, you can expect to line up for your visitor pass. Really. Next you enter a room full of unknown faces, graduates just like you, and then you realise you're in this with 18 other people, going through the same thing as you. 3 weeks later you leave with many memories, colleagues you can call your friends, and a video of your presentation. Vanessa, the Graduate Manager, will also take lots of photos and keep you (well) fed. Well that's not all you leave with, you are also equipped with a wealth of knowledge and contacts within Oracle, both that will help you throughout your career there. What training is involved? We started our Oracle experience with 3 weeks of training, consisting of employee orientation, extensive product training, presentations on the various lines of business (LoB's), followed by sales and presentation training. While there was potential for an information overload, maybe even death by Powerpoint, we were able to have access to the presentations for future reference, which was very helpful. This period also allowed us to start networking, not only with the graduates, but with the managers who presented to us, as well as through the monthly chinwag, HR celebrations and even with the sharing of tea facilities. We also had a team bonding day when we recorded a "commercial" within groups, and learned how to play an Irish drum. Overall, the training period helped us to learn about Oracle, as well as ourselves, and to prepare us for our transition into our rotations. Where to now? I'm now into my 2nd week of my first graduate rotation. It has been exciting to finally get out into the work environment and utilise that knowledge we gained from training. My manager has been a great mentor, extremely knowledgeable, and it has been good being able to participate in meetings, conference calls and make a contribution towards the business. And while we aren't necessarily working directly with the other graduates, they are still reachable via email, Pidgin and lunch and they are important as a resource and support, after all, they are going through a similar experience to you. While it is only the beginning, there is a lot more to learn and a lot more to experience along the way, especially because, as we learned during training, at Oracle, the only constant is change.

  Read the article

• Customizing UPK outputs (Part 2 - Player)

  - by [email protected]

  There are a few things that can be done to give the Player output a personalized look to match your corporate branding. In my previous post, I talked about changing the logo. In addition to the logo, you can change the graphic in the heading, button colors, border colors and many other items. Prior to making any customizations, I strongly recommend making a copy of the existing Player style. This will give you a backup in case things go wrong. I'd also recommend that you create your own brand. This way, when you install the newest updates from us, your brand will remain intact. Creating your own brand is pretty easy. Make sure you have modify permissions on the publishing styles directory, if you are using a multi-user installation. Under the Publishing/Styles folder, create a new folder with your company name. Copy all the publishing styles from the UPK folder to your newly created folder. Now, when you go through the Publishing wizard, you will have two categories to choose from: the UPK category or your custom category. Now, for updating the Player output. First, the graphic that appears on the right hand side of the Player. If you're using a multi-user installation, check out the player style from your custom brand. Open the player style. Open the img folder. The file named "banner_image.png" represents the graphic that appears on the right hand side of the player. It is currently sized at 425 x 54. Try to keep your graphic about the same size. Rename your graphic file to be "banner_image.png", and drag it into the img folder. Save the package. Check in the package if you are in a multi-user installation. You've just updated the banner heading! Next, let's work on updating some of the other colors in the player. All the customizable areas are located in the skin.css file which is in the root of the Player style. Many of our customers update the colors to match their own theme. You don't have to be a programmer to make these changes, honest. :) To change the colors in the player: Make a copy of the original skin.css file. (This is to make sure you have a working version to revert to, in case something goes wrong.) Open the skin.css file from the Player package. You can edit it using Notepad. Make the desired changes. Save the file. Save the package. Publish to view your new changes. When you open the skin.css, you will see groupings like this: .headerDivbar { height: 21px; background-color: #CDE2FD; } Change the value of the background-color to the color of your choice. Note that you cannot use "red" as a color, but rather you should enter the hexadecimal color code. If you don't know the color code, search the web for "hexadecimal colors" and you'll find many sites to provide the information. Here are a few of the variables that you can update. Heading: .headerDivbar -this changes the color of the banner that appears under the graphic Button colors: .navCellOn - changes the color of the mode buttons when your mouse is hovering on them. .navCellOff - changes the color of the mode buttons when the mouse is not over them Lines: .thorizontal - this is the color of the horizontal lines surrounding the outline .tvertical - this is the color of the vertical lines on the left and right margin in the outline. .tsep - this is the color of the line that separates the outline from the content area Search frame: .tocSearchColor - this is the color of the search area .tocFrameText - this is the background color of the TOC tree. Hint: If you want to try out the changes prior to updating the style, you can update the skin.css in some content you've already published for the player (it's located in the css folder of the player package). This way, you can immediately see the changes without going through publishing. Once you're happy with the changes, update the skin.css in player style. Want to customize more? Refer to the "Customizing the Player" section of the Content Development manual for more details on all the options in the skin.css that can be changed, and pictures of what each variable controls. I'd love to see how you've customized the player for your corporate needs. Also, if there are other areas of the player you'd like to modify but have not been able to, let us know. Feel free to share your thoughts in the comments. --Maria Cozzolino, Manager of Requirements & UI Design for UPK

  Read the article

• CD/DVD drive not mounted when inserted with Disc of any kind

  - by Cisco Sán

  I just noticed that if a insert a CD or a DVD of any kind, the Drive will start spinning but it will not show the mounted disc. Before it used to ask me what to do with the media inserted. Now it doesn't even do that. I ran in the terminal this code: eject -n and it displays this: " eject: device is `/dev/sr0'" what can I do to get the functionality back on my drive. also ran this command: sudo mount -o ro,unhide,uid=1000 /dev/cdrom /mnt/cdrom but in return i get this: " mount: mount point /mnt/cdrom does not exist" Running Ubuntu 11.10 HERE IS THE HISTORY UNTIL NOW thanks Waltinator: I ran the 'dmesg' but don't know what I'm looking for. Im a newbie on this. The same thing with the 'ls -rlt /var/log' command. Should I create the directory for the mount? at this point really don't know what to do. – Cisco Sán 7 hours ago Here are 3 lines from my dmesg after I successfully inserted a CD: [ 4804.416018] wlan0: no IPv6 routers present [ 8214.125450] ISdit ISO 9660 Extensions: Microsoft Joliet Level 3 [ 8214.136556] ISO 9660 Extensions: RRIP_1991A The first line is a previous event, my wireless going online. The next 2 lines are a good result. The number in square brackets is "seconds since boot", the rest of the line is usually helpful. And no, you should NOT create the mount point. Let's try to get the automatic mounting to work. – waltinator 7 hours ago ok this are my last 3 lines on the 'dmesg' [ 18.130819] init: plymouth-stop pre-start process (1396) terminated with status 1 [ 28.780011] wlan0: no IPv6 routers present [ 505.632119] CE: hpet increased min_delta_ns to 20113 nsec – Cisco Sán 6 hours ago It looks like your CD/DVD drive is not connected to the data bus, and not causing an interrupt when you insert a platter. – waltinator 6 hours ago Try dmesg | grep -A8 CD-ROM which should show you what the system thought was available when it came up. – waltinator 6 hours ago here is my printout [0.774351] scsi 0:0:0:0: CD-ROM HL-DT-ST DVD+-RW GSA-T40N A100 PQ: 0 ANSI: 5 [0.778117] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray [0.778122] cdrom: Uniform CD-ROM driver Revision: 3.20 [0.778282] sr 0:0:0:0: Attached scsi CD-ROM sr0 [0.778340] sr 0:0:0:0: Attached scsi generic sg0 type 5 [0.780416] Freeing unused kernel memory: 984k freed [0.780732] Write protecting the kernel read-only data: 10240k [0.780986] Freeing unused kernel memory: 20k freed [0.786331] Freeing unused kernel memory: 1400k freed [0.804912] udevd[90]: starting version 173 [0.874178] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [0.874208] r8169 0000:02:00.0: PCI INT A - GSI 16 (level, low) - IRQ 16 OK, your system sees the drive. Can you open and close the tray with eject and eject -t? Run udevadm monitor while you insert a CD (type ^C when done) and see if you get "change" and "add" messages. – waltinator 6 hours ago ok, "eject" works perfectly "eject -t" does nothing. this is the message for "udevadm monitor": KERNEL[13771.009267] change /devices/pci0000:00/0000:00:1f.1/host0/target0:0:0/0:0:0:0/block/sr0 (block) UDEV [13773.878887] change /devices/pci0000:00/0000:00:1f.1/host0/target0:0:0/0:0:0 /block/sr0 (block) – Cisco Sán 6 hours ago sudo hwinfo --cdrom (the hwinfo package is installable through Software Center) describes my CD-ROM, try it. – waltinator 4 hours ago My read out from the "sudo hwinfo --cdrom" are the following: hal.1: read hal dataprocess 2753: arguments to dbus_move_error() were incorrect, assertion "(dest) == NULL || !dbus_error_is_set ((dest))" failed in file ../../dbus/dbus-errors.c line 280. This is normally a bug in some application using the D-Bus library. libhal.c 3483 : Error unsubscribing to signals, error=The name org.freedesktop.Hal was not provided by any .service files 22: SCSI 00.0: 10602 CD-ROM (DVD) [Created at block.247] Unique ID: KD9E.JgkxTS4hgl2 Parent ID: 3p2J.gdUMCD83e+E SysFS ID: /class/block/sr0 SysFS BusID: 0:0:0:0 SysFS Device Link: /devices/pci0000:00/0000:00:1f.1/host0/target0:0:0/0:0:0:0 Hardware Class: cdrom Model: "HL-DT-ST DVD+-RW GSA-T40N" Vendor: "HL-DT-ST" Device: "DVD+-RW GSA-T40N" Revision: "A100" Driver: "ata_piix", "sr" Driver Modules: "ata_piix" Device File: /dev/sr0 (/dev/sg0) Device Files: /dev/sr0, /dev/scd0, /dev/disk/by-id/ata-HL-DT-ST_DVD+_-RW_GSA-T40N_K048BJ74257, /dev/disk/by-path/pci-0000:00:1f.1-scsi-0:0:0:0, /dev/cdrom, /dev/cdrw, /dev/dvd, /dev/dvdrw Device Number: block 11:0 (char 21:0) Features: DVD Config Status: cfg=new, avail=yes, need=no, active=unknown Attached to: #17 (IDE interface) Drive Speed: 31 Volume ID: "Movie" Publisher: "INTERVIDEO" Creation date: "20050424162207000" Thanks for the help. To Castro, hope this is what you meant and sorry for the comments..

  Read the article

• Which of these algorithms is best for my goal?

  - by JonathonG

  I have created a program that restricts the mouse to a certain region based on a black/white bitmap. The program is 100% functional as-is, but uses an inaccurate, albeit fast, algorithm for repositioning the mouse when it strays outside the area. Currently, when the mouse moves outside the area, basically what happens is this: A line is drawn between a pre-defined static point inside the region and the mouse's new position. The point where that line intersects the edge of the allowed area is found. The mouse is moved to that point. This works, but only works perfectly for a perfect circle with the pre-defined point set in the exact center. Unfortunately, this will never be the case. The application will be used with a variety of rectangles and irregular, amorphous shapes. On such shapes, the point where the line drawn intersects the edge will usually not be the closest point on the shape to the mouse. I need to create a new algorithm that finds the closest point to the mouse's new position on the edge of the allowed area. I have several ideas about this, but I am not sure of their validity, in that they may have far too much overhead. While I am not asking for code, it might help to know that I am using Objective C / Cocoa, developing for OS X, as I feel the language being used might affect the efficiency of potential methods. My ideas are: Using a bit of trigonometry to project lines would work, but that would require some kind of intense algorithm to test every point on every line until it found the edge of the region... That seems too resource intensive since there could be something like 200 lines that would have each have to have as many as 200 pixels checked for black/white.... Using something like an A* pathing algorithm to find the shortest path to a black pixel; however, A* seems resource intensive, even though I could probably restrict it to only checking roughly in one direction. It also seems like it will take more time and effort than I have available to spend on this small portion of the much larger project I am working on, correct me if I am wrong and it would not be a significant amount of code (100 lines or around there). Mapping the border of the region before the application begins running the event tap loop. I think I could accomplish this by using my current line-based algorithm to find an edge point and then initiating an algorithm that checks all 8 pixels around that pixel, finds the next border pixel in one direction, and continues to do this until it comes back to the starting pixel. I could then store that data in an array to be used for the entire duration of the program, and have the mouse re-positioning method check the array for the closest pixel on the border to the mouse target position. That last method would presumably execute it's initial border mapping fairly quickly. (It would only have to map between 2,000 and 8,000 pixels, which means 8,000 to 64,000 checked, and I could even permanently store the data to make launching faster.) However, I am uncertain as to how much overhead it would take to scan through that array for the shortest distance for every single mouse move event... I suppose there could be a shortcut to restrict the number of elements in the array that will be checked to a variable number starting with the intersecting point on the line (from my original algorithm), and raise/lower that number to experiment with the overhead/accuracy tradeoff. Please let me know if I am over thinking this and there is an easier way that will work just fine, or which of these methods would be able to execute something like 30 times per second to keep mouse movement smooth, or if you have a better/faster method. I've posted relevant parts of my code below for reference, and included an example of what the area might look like. (I check for color value against a loaded bitmap that is black/white.) // // This part of my code runs every single time the mouse moves. // CGPoint point = CGEventGetLocation(event); float tX = point.x; float tY = point.y; if( is_in_area(tX,tY, mouse_mask)){ // target is inside O.K. area, do nothing }else{ CGPoint target; //point inside restricted region: float iX = 600; // inside x float iY = 500; // inside y // delta to midpoint between iX,iY and tX,tY float dX; float dY; float accuracy = .5; //accuracy to loop until reached do { dX = (tX-iX)/2; dY = (tY-iY)/2; if(is_in_area((tX-dX),(tY-dY),mouse_mask)){ iX += dX; iY += dY; } else { tX -= dX; tY -= dY; } } while (abs(dX)>accuracy || abs(dY)>accuracy); target = CGPointMake(roundf(tX), roundf(tY)); CGDisplayMoveCursorToPoint(CGMainDisplayID(),target); } Here is "is_in_area(int x, int y)" : bool is_in_area(NSInteger x, NSInteger y, NSBitmapImageRep *mouse_mask){ NSAutoreleasePool * pool = [[NSAutoreleasePool alloc] init]; NSUInteger pixel[4]; [mouse_mask getPixel:pixel atX:x y:y]; if(pixel[0]!= 0){ [pool release]; return false; } [pool release]; return true; }

  Read the article

• How to Apply a Business Card Template to a Contact and Customize it in Outlook 2013

  - by Lori Kaufman

  If you want to add a business card template to an existing contact in Outlook, you can do so without having to enter all of the information again. We will also show you how to customize the layout and format of the text on the card. Microsoft provides a couple of business card templates you can use. We will use their Blue Sky template as an example. To open the archive file for the template you downloaded, double-click on the .cab file. NOTE: You can also use a tool like 7-Zip to open the archive. A new Extract tab becomes available under Compressed Folder Tools and the files in the archive are listed. Select the .vcf file in the list of files. This automatically activates the Extract tab. Click Extract To and select a location or select Choose location if the desired location is not on the drop-down menu. Select a folder in which you want to save the .vcf file on the Copy Items dialog box and click Copy. NOTE: Use the Make New Folder button to create a new folder for the location, if desired. Double-click on the .vcf file that you copied out of the .cab archive file. By default, .vcf files are associated with Outlook so, when you double-click on a .vcf file, it automatically opens in a Contact window in Outlook. Change the Full Name to match the existing contact to which you want to apply this template. Delete the other contact info from the template. If you want to add any additional information not in the existing contact, enter it. Click Save & Close to save the contact with the new template. The Duplicate Contact Detected dialog box displays. To update the existing contact, select the Update information of selected Contact option. Click Update. NOTE: If you want to create a new contact from this template, select the Add new contact option. With the Contacts folder open (the People link on the Navigation Bar), click Business Card in the Current View section of the Home tab. You may notice that not all the fields from your contact display on the business card you just updated. Double-click on the contact to update the contact and the business card. On the Contact window, right-click on the image of the business card and select Edit Business Card from the popup menu. The Edit Business Card dialog box displays. You can change the design of the card, including changing he background color or image. The Fields box allows you to specify which fields display on the business card and in what order. Notice, in our example, that Company is listed below the Full Name, but no text displays on the business card below the name. That’s because we did not enter any information for Company in the Contact. We have information in Job Title. So, we select Company and click Remove to remove that field. Now, we want to add Job Title. First, select the field below which you want to add the new field. We select Full Name to add the Job Title below that. Then, we click Add and select Organization | Job Title from the popup menu to insert the Job Title. To make the Job Title white like the name, we select Job Title in the list of Fields and click the Font Color button in the Edit section. On the Color dialog box, select the color you want to use for the text in the selected field. Click OK. You can also make text bold, italic, or underlined. We chose to make the Job Title bold and the Full Name bold and italic. We also need to remove the Business Phone because this contact only has a mobile phone number. So, we add a Mobile Phone from the Phone submenu. Then, we need to remove enough blank lines so the Mobile Phone is visible on the card. We also added a website and email address and removed more blank lines so they are visible. You can also move text to the right side of the card or make it centered on the card. We also changed the color of the bottom three lines to blue. Click OK to accept your changes and close the dialog box. Your new business card design displays on the Contact window. Click Save & Close to save the changes you made to the business card for this contact and close the Contact window. The final design of the business card displays in the Business Card view on the People screen. If you have a signature that contains the business card for the contact you just updated, you will also need to update the signature by removing the business card and adding it again using the Business Card button in the Signature editor. You can also add the updated Business Card to a signature without the image or without the vCard (.vcf) file.     

  Read the article

• What are some concise and comprehensive introductory guide to unit testing for a self-taught programmer [closed]

  - by Superbest

  I don't have much formal training in programming and I have learned most things by looking up solutions on the internet to practical problems I have. There are some areas which I think would be valuable to learn, but which ended up both being difficult to learn and easy to avoid learning for a self-taught programmer. Unit testing is one of them. Specifically, I am interested in tests in and for C#/.NET applications using Microsoft.VisualStudio.TestTools in Visual Studio 2010 and/or 2012, but I really want a good introduction to the principles so language and IDE shouldn't matter much. At this time I'm interested in relatively trivial tests for small or medium sized programs (development time of weeks or months and mostly just myself developing). I don't necessarily intend to do test-driven development (I am aware that some say unit testing alone is supposed to be for developing features in TDD, and not an assurance that there are no bugs in the software, but unit testing is often the only kind of testing for which I have resources). I have found this tutorial which I feel gave me a decent idea of what unit tests and TDD looks like, but in trying to apply these ideas to my own projects, I often get confused by questions I can't answer and don't know how to answer, such as: What parts of my application and what sorts of things aren't necessarily worth testing? How fine grained should my tests be? Should they test every method and property separately, or work with a larger scope? What is a good naming convention for test methods? (since apparently the name of the method is the only way I will be able to tell from a glance at the test results table what works in my program and what doesn't) Is it bad to have many asserts in one test method? Since apparently VS2012 reports only that "an Assert.IsTrue failed within method MyTestMethod", and if MyTestMethod has 10 Assert.IsTrue statements, it will be irritating to figure out why a test is failing. If a lot of the functionality deals with writing and reading data to/from the disk in a not-exactly trivial fashion, how do I test that? If I provide a bunch of files as input by placing them in the program's directory, do I have to copy those files to the test project's bin/Debug folder now? If my program works with a large body of data and execution takes minutes or more, should my tests have it do the whole use all of the real data, a subset of it, or simulated data? If latter, how do I decide on the subset or how to simulate? Closely related to the previous point, if a class is such that its main operation happens in a state that is arrived to by the program after some involved operations (say, a class makes calculations on data derived from a few thousands of lines of code analyzing some raw data) how do I test just that class without inevitably ending up testing that class and all the other code that brings it to that state along with it? In general, what kind of approach should I use for test initialization? (hopefully that is the correct term, I mean preparing classes for testing by filling them in with appropriate data) How do I deal with private members? Do I just suck it up and assume that "not public = shouldn't be tested"? I have seen people suggest using private accessors and reflection, but these feel like clumsy and unsuited for regular use. Are these even good ideas? Is there anything like design patterns concerning testing specifically? I guess the main themes in what I'd like to learn more about are, (1) what are the overarching principles that should be followed (or at least considered) in every testing effort and (2) what are popular rules of thumb for writing tests. For example, at one point I recall hearing from someone that if a method is longer than 200 lines, it should be refactored - not a universally correct rule, but it has been quite helpful since I'd otherwise happily put hundreds of lines in single methods and then wonder why my code is so hard to read. Similarly I've found ReSharpers suggestions on member naming style and other things to be quite helpful in keeping my codebases sane. I see many resources both online and in print that talk about testing in the context of large applications (years of work, 10s of people or more). However, because I've never worked on such large projects, this context is very unfamiliar to me and makes the material difficult to follow and relate to my real world problems. Speaking of software development in general, advice given with the assumptions of large projects isn't always straightforward to apply to my own, smaller endeavors. Summary So my question is: What are some resources to learn about unit testing, for a hobbyist, self-taught programmer without much formal training? Ideally, I'm looking for a short and simple "bible of unit testing" which I can commit to memory, and then apply systematically by repeatedly asking myself "is this test following the bible of testing closely enough?" and then amending discrepancies if it doesn't.

  Read the article

• Setup Custom Portal & Content Enabled Domain

  - by Stefan Krantz

  When overlooking the past year we have seen a large increase in deployments where only some parts of the WebCenter Suite infrastructure has been used. The most common from my personal perspective is a domain topology that includes: WebCenter Custom Portal, WebCenter Content and Oracle HTTP ServicesToday its very common to see installation where the whole suite is installed when the use case only requires the custom portal and some sub component like WebCenter Content. This post will go into detail on how to minimize the deployment time and effort by only laying down the necessary managed servers needed, by following this proposed method you will minimize the configuration steps and only install the required components and schema's, configure only the necessary components and minimize the impact of architectural changes through reduced dependencies. Assumptions: Oracle 11g Database installed SYS or equivalent access to Database to setup schema's via RCU Running Operating System supporting JDK 7 Update 2 (Check support matrix here) Good understanding of WebLogic Architecture Binaries: Oracle JDK 7 Update 2 (1.7.0_02) (Download) Oracle WebLogic 10.3.6 (Download) Oracle WebCenter Binaries (11.1.1.6) (Download) Oracle WebCenter Content Binaries (11.1.1.6) (Download 1) (Download 2) Oracle HTTP Services (11.1.1.6) (Download) Oracle Repository Creation Utility (11.1.1.6) (Download Linux or Windows) Schema's: Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} MDS - Meta Data Services (WebCenter and OWSM) WebCenter (WebCenter Schema) OCS (Oracle WebCenter Content) Activities (WebCenter Activities) OPSS (Policy Store for WebCenter) Installation Structure: - [Installation Home]/Middleware    - Oracle_WC1 (WebCenter Installation)    - Oracle_WT1 (Oracle WebTier)    - Oracle_ECM (WebCenter Content)    - wlserver_10.3 (Weblogic installation)- [Installation Home]/domains    - webcenter (WebCenter Domain)    - instances (OHS/OPMN instance)- [Installation Home]/applications- [Installation Home]/JDK1.7.0_02 Installation and Configuration Steps: Install Java and configure Java Home Extract the Java Installable (jdk-7u2-linux-x64) to [Installation Home]/JDK1.7.0_02 Add JAVA_HOME to Environment Settings (JAVA_HOME=[Installation Home]/JDK1.7.0_02) Update PATH in Environment Settings (PATH=$JAVA_HOME/bin:$PATH) Install WebLogic Server (Middleware Home) Run the installer / execute jar file (java - jar wls1036_generic.jar) Create the Middleware Home under [Installation Home]/Middleware Install WebCenter Portal (Extend Middleware Home) Extract the compressed file (ofm_wc_generic_11.1.1.6.0_disk1_1of1.zip) to a temp folder Execute runInstaller under folder (DISK1/) with following command (runInstaller -jreLoc $JAVA_HOME) Make sure to install in following structure ([Installation Home]/Middleware/Oracle_WC1) Install WebCenter Content (Extend Middleware Home) Extract the compressed files (ofm_wcc_generic_11.1.1.6.0_disk1_1of2.zip & ofm_wcc_generic_11.1.1.6.0_disk1_2of2.zip) to the same temp folder Execute runInstaller under folder (DISK1/) with following command (runInstaller -jreLoc $JAVA_HOME) Make sure to install in following structure ([Installation Home]/Middleware/Oracle_ECM) Configure Initial Domain (Domain name webcenter) Execute configuration tool - [Installation Home]/Middleware/wlserver_10.3/common/bin/config Select "Create a New Weblogic Domain" Select following template (Basic Weblogic Server Domain, Oracle Enterprise Manager, Oracle WSM Policy Manager, Oracle JRF) Create new domain with name webcenter under following location ([Installation Home]/domains) for applications ([Installation Home]/applications) Select Production Mode Finish Configuration wizard Setup username for startup scripts - Add a new file called boot.properties to ([Installation Home]/domains/webcenter/servers/AdminServer/security)Add following lines to boot.propertiesusername=weblogicpassword=[password clear text, it will be encrypted during first start] Start AdminServer in the background ([Installation Home]/domains/webcenter/bin/startWeblogic) Install and Configure Oracle WebTier (OHS Server) Extract compressed file (ofm_webtier_linux_11.1.1.6.0_64_disk1_1of1.zip) to a temp folder Execute runInstaller under folder (DISK1/) with following command (runInstaller) Select Install & Configure option Deselect Oracle WebCache Auto Configure Ports Configure Schema's with RCU (Repository Creation Utility) Extract compressed file (ofm_rcu_linux_11.1.1.6.0_disk1_1of1.zip) to a temp folder Execute rcu with following command ([temp]/rcuHome/rcu) Make sure database meets RCU requirements, particular (PROCESSES is 200 or more) Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} Using SQLPLUS and sys user tou can update this configuration in the database with following procedure:ALTER SYSTEM SET PROCESSES=200 SCOPE=SPFILE shutdown immediate startup Create and Configure following schemas:MDS - Meta Data Services (WebCenter and OWSM)WebCenter (WebCenter Schema)OCS (Oracle WebCenter Content)Activities (WebCenter Activities)OPSS (Policy Store for WebCenter) Remember selected schema prefix and password (will be used later) Configure WebCenter Portal instance (WC_CustomPortal) Execute following command to start configuration wizard ([Installation Home]/Middleware/Oracle_WC1/common/bin/config) Select Extend an Existing WebLogic domain Select the existing webcenter domain ([Installation Home]/domains/webcenter) Select Extend my domain using existing extension templateBrowse to ([Installation Home]/Middleware/Oracle_WC1/common/templates/applications)Select oracle.wc_custom_portal_template_11.1.1.jar Select to configure (Managed Servers/Clusters/Machines) On the Managed Server Screen you can now configure 1 or more WC_CustomPortal managed servers (name them WC_CustomPortal[n] (skip numbering if not clustered)) In case of two WC_CustomPortal Servers then create a Cluster (any name) and make sure the managed servers join the new cluster Create a new machine with same name as the current machine Make sure the AdminServer and WC_CustomPortal[n] managed servers joins the machine Finish the configuration wizard Stop AdminServer ([Installation Home]/domains/webcenter/bin/stopWeblogic) Start AdminServer in the background ([Installation Home]/domains/webcenter/bin/startWeblogic) Start WC_CustomPortal in the foreground (([Installation Home]/domains/webcenter/bin/startManagedServer WC_CustomPortal))- repeat for each WC_CustomPortal instance on the host Give credentials for weblogic user on start up Copy folder security including file boot.properties - from ([Installation Home]/domains/webcenter/servers/AdminServer/) to ([Installation Home]/domains/webcenter/servers/WC_CustomPortal/) Result should be ([Installation Home]/domains/webcenter/servers/WC_CustomPortal/security/boot.properties) Configure WebCenter Content instance (UCM_server1) Execute following command to start configuration wizard ([Installation Home]/Middleware/Oracle_ECM/common/bin/config) Select Extend an Existing WebLogic domain Select Oracle Universal Content Management - Content Server Select to configure (Managed Servers/Clusters/Machines) On Managed Server Screen create only one managed server instance (UCM_server1 on port 16200 (you can select any other available port)) Make sure the UCM_server1 managed server joins the machine Finish the configuration wizard Stop AdminServer ([Installation Home]/domains/webcenter/bin/stopWeblogic) Start AdminServer in the background ([Installation Home]/domains/webcenter/bin/startWeblogic) Start UCM_server1 in the foreground ([Installation Home]/domains/webcenter/bin/startManagedServer UCM_server1)Give credentials for weblogic user on start up Copy folder security including file boot.properties - from ([Installation Home]/domains/webcenter/servers/AdminServer/) to ([Installation Home]/domains/webcenter/servers/UCM_server1/ Result should be ([Installation Home]/domains/webcenter/servers/UCM_server1/security/boot.properties) Post Configure WebCenter Content instance for WebCenter Portal Open a browser where you have support for Java applets - navigate to http://host:port/cs WARNING: The page that you are presented with after authentication will only appear once for each instance WARNING: Make sure you set correct storage options - also remember to consider file sharing options if you like to cluster your Content Server instance over multiple hosts Set an appropriate Auto number prefix Update the Server Socket Port: Commonly set to (4444)  used for RIDC communication (a requirement for WebCenter Portal) Update the IP Address Filter to include the IP that is planned to access the server over RIDC - at the minimum add the ip address of the current host (this option can be updated later via EM) Stop UCM_server1 ([Installation Home]/domains/webcenter/bin/stopManagedServer UCM_server1) Start UCM_server1 in the background([Installation Home]/domains/webcenter/bin/startManagedServer UCM_server1) Open a browser where you have support for Java applets - navigate to http://host:port/cs Navigate to Administration/Admin Server Go to General ConfigurationCheck Enable AccountsIn Additional Configuration Variables (Add on two lines) Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} AllowUpdateForGenwww=1CollectionUseCache=1 Save the changes and go to Component Manager Click on the link advanced component manager Enable following components Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} Folders_g, WebCenterConfigure, SiteStudio, SiteStudioExternalApplications, DBSearchContainsOpSupport WARNING: Make sure that following component is disabled: FrameworkFolders Stop UCM_server1 ([Installation Home]/domains/webcenter/bin/stopManagedServer UCM_server1) Start UCM_server1 in the background([Installation Home]/domains/webcenter/bin/startManagedServer UCM_server1) Open a browser where you have support for Java applets - navigate to http://host:port/cs Navigate to Administration/Site Studio Administration and update - Do not forget to save and submit each page Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} Set Default ProjectSet Default WebAssets Post Configure Oracle WebTier (OHS) to include Content Server and WebCenter Portal application context Update following file - [Installation Home]/domains/instances/instance1/config/OHS/ohs1/mod_wl_ohs.conf For single add lines from following example: Link For clustered environment add lines from following template (note the clustering in example on applies to WC_CustomPortal): Link For more information on this: http://docs.oracle.com/cd/E23943_01/core.1111/e12037/contentsvr.htm#WCEDG318 Optional - Configure JOC Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} Follow instructions: http://docs.oracle.com/cd/E23943_01/core.1111/e12037/extend_wc.htm#WCEDG264 Optional (Recommended) - Configure Node Manager Follow instructions: Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} http://docs.oracle.com/cd/E23943_01/core.1111/e12037/node_manager.htm#WCEDG277 Optional (Mandatory for clustered environments) - Re-Associate Policy Store to Database or OID Follow instructions: Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} http://docs.oracle.com/cd/E23943_01/webcenter.1111/e12405/wcadm_security_credstore.htm#CFHDEDJH Optional - Configure Coherence for Content Presenter Follow instructions in Blog Post (This post is for PS4): https://blogs.oracle.com/ATEAM_WEBCENTER/entry/enabling_coherence_for_content_presenter Other Recommended Post Cloning WebCenter Custom Portal - https://blogs.oracle.com/ATEAM_WEBCENTER/entry/cloning_a_webcenter_portal_managedImproving WebCenter Performance through caching - https://blogs.oracle.com/ATEAM_WEBCENTER/entry/improving_webcenter_performance

  Read the article

• CodePlex Daily Summary for Thursday, December 30, 2010

  CodePlex Daily Summary for Thursday, December 30, 2010Popular ReleasesVarddienis - Windows Sidebar sikriks: Varddienis 0.9.5.0: Pievienota "Svetku" funkcija; Tiek paraditi Latvijas valsts svetki, atceres un atzimejamas dienas. Pievienoti “Atrie taustini” jeb isceli (laujot atrak izmantot Varddiena iespejas); Pievienota jauna poga - "Isceli", kas lauj lietotajam apskatit Varddieni pieejamos iscelus, un to taustinus. Nelielas izmainas: Nedaudz uzlabots JavaScript kods, Izmainits lidojošo logu aizveršanas krustinš – tagad tas klust dzeltens, ja uz ta uzbrauc ar peli; Ieverojami parkartoti un samazinati sik...SQL Monitor - tracking sql server activities: SQL Monitor 3.0 alpha 8: 1. added truncate table/defrag index/check db functions 2. improved alert 3. fixed problem with alert causing config file corrupted(hopefully)People's Note: People's Note 0.20: Version 0.20 is all about polishing the UI and supporting other developers. Several screens got better handling of the "close" button and the Escape key. The ink note screen got more traditional sketching colours, instead of the primaries. It also got a greater brush size. Messages for network errors have been improved. The Evernote API library got a Win32 target. Readme.txt was updated with additional instructions. To install: copy the appropriate CAB file onto your WM device and run i...ASP.NET Comet Ajax Library (Reverse Ajax - Server Push): Object Cache Sample: Object cache sample for Windows Forms Applications. This sample project demonstrates the usage of PCache class.Analysis Services Stored Procedure Project: 1.3.5 Release: This release includes the following fixes and new functionality: Updates to GetCubeLastProcessedDate to work with perspectives Fixes to reports that call Discover functions improving drillthrough functions against perspectives improving ExecuteDrillthroughAndFixColumns logic fixing situation where MDX query calling certain ASSP sprocs which opened external connections caused deadlock to SSAS processing small fix to Partition code when DbColumnName property doesn't exist changes...DocX: DocX v1.0.0.11: Building Examples projectTo build the Examples project, download DocX.dll and add it as a reference to the project. OverviewThis version of DocX contains many bug fixes, it is a serious step towards a stable release. Added1) Unit testing project, 2) Examples project, 3) To many bug fixes to list here, see the source code change list history.Cosmos (C# Open Source Managed Operating System): 71406: This is the second release supporting the full line of Visual Studio 2010 editions. Changes since release 71246 include: Debug info is now stored in a single .cpdb file (which is a Firebird database) Keyboard input works now (using Console.ReadLine) Console colors work (using Console.ForegroundColor and .BackgroundColor)AutoLoL: AutoLoL v1.5.0: Added the all new Masteries Browser which replaces the Quick Open combobox AutoLoL will now attemt to create file associations for mastery (*.lolm) files Each Mastery Build can now contain keywords that the Masteries Browser will use for filtering Changed the way AutoLoL detects if another instance is already running Changed the format of the mastery files to allow more information stored in* Dialogs will now focus the Ok or Cancel button which allows the user to press Return to clo...Paint.NET PSD Plugin: 1.6.0: Handling of layer masks has been greatly improved. Improved reliability. Many PSD files that previously loaded in as garbage will now load in correctly. Parallelized loading. PSD files containing layer masks will load in a bit quicker thanks to the removal of the sequential bottleneck. Hidden layers are no longer made visible on save. Many thanks to the users who helped expose the layer masks problem: Rob Horowitz, M_Lyons10. Please keep sending in those bug reports and PSD repro files!Razor Templating Engine: Razor Templating Engine v1.2: Changes: ADDED: Standard namespaces imports for all templates: System, System.Collections.Generic, System.Linq (Changeset 5635) ADDED: Methods for Precompilation (Changeset 3283) CHANGED: Refactored precompilation to be exposed per-TemplateService. (Changeset 3440) CHANGED: Added more descriptive compilation exception message. (Changeset 3629) FIXED: Forced reference to Microsoft.CSharp to correct support for testing frameworks. (Changeset 3689) FIXED: Added support for nested anonymous obj...Facebook C# SDK: 4.1.1: From 4.1.1 Release: Authentication bug fix caused by facebook change (error with redirects in Safari) Authenticator fix, always returning true From 4.1.0 Release Lots of bug fixes Removed Dynamic Runtime Language dependencies from non-dynamic platforms. Samples included in release for ASP.NET, MVC, Silverlight, Windows Phone 7, WPF, WinForms, and one Visual Basic Sample Changed internal serialization to use Json.net BREAKING CHANGE: Canvas Session is no longer supported. Use Signed...Catel - WPF and Silverlight MVVM library: 1.0.0: And there it is, the final release of Catel, and it is no longer a beta version!EnhSim: EnhSim 2.2.7 ALPHA: 2.2.7 ALPHAThis release supports WoW patch 4.03a at level 85 To use this release, you must have the Microsoft Visual C++ 2010 Redistributable Package installed. This can be downloaded from http://www.microsoft.com/downloads/en/details.aspx?FamilyID=A7B7A05E-6DE6-4D3A-A423-37BF0912DB84 To use the GUI you must have the .NET 4.0 Framework installed. This can be downloaded from http://www.microsoft.com/downloads/en/details.aspx?FamilyID=9cfb2d51-5ff4-4491-b0e5-b386f32c0992 - Mongoose has bee...LINQ to Twitter: LINQ to Twitter Beta v2.0.19: Mono 2.8, Silverlight, OAuth, 100% Twitter API coverage, streaming, extensibility via Raw Queries, and added documentation. Bug fixes.Euro for Windows XP: ChangeRegionalSettings 1..0: *Flickr Wallpaper Rotator (for Windows desktop): Wallpaper Flickr 1.1: Some minor bugfixes (mostly covering when network connection is flakey, so I discovered them all while at my parents' house for Christmas).NoSimplerAccounting: NoSimplerAccounting 6.0: -Fixed a bug in expense category report.NHibernate Mapping Generator: NHibernate Mapping Generator 2.0: Added support for Postgres (Thanks to Angelo)NewLife XCode: XCode v6.5.2010.1223 ????（????v3.5??）: XCode v6.5.2010.1223 ????，??： NewLife.Core ??? NewLife.Net ??? XControl ??? XTemplate ????，??C#?????? XAgent ???? NewLife.CommonEnitty ??????（???，XCode??????） XCode?? ?????????，??????????????????，?????95% XCode v3.5.2009.0714 ??，?v3.5?v6.0???????????????，?????????。v3.5???????????，??????????????。 XCoder ??XTemplate?????????，????????XCode??? XCoder_Src ???????（????XTemplate????），??????????????????Umbraco CMS: Umbraco 4.6 Beta - codename JUNO: The Umbraco 4.6 beta (codename JUNO) release contains many new features focusing on an improved installation experience, a number of robust developer features, and contains more than 89 bug fixes since the 4.5.2 release. Improved installer experience Updated Starter Kits (Simple, Blog, Personal, Business) Beautiful, free, customizable skins included Skinning engine and Skin customization (see Skinning Documentation Kit) Default dashboards on install with hide option Updated Login t...New ProjectsAlquerque.net: Quer mostrar todo seu potencial? Destacar sua idéia inovadora? Desenvolva uma solução na plataforma .NET e prove que você está preparado para o mercado!Buccaneer: Buccaneer is a very extensive version of the windows explorer, which can be even furter extended with selfmade plugins. It is developed in c#.Chianti: Project Chianticomputing pi with a webcam: computing pi with a webcam and a spinning plate using buffon's methodConfree for Outlook: Confree lets you create audio conferences from Claro / Telmex directly from Outlook.Esurfing: EsurfingFoursquare Helper for WebMatrix: The Foursquare Helper for WebMatrix makes it simple to integrate Foursquare in your site. With a few lines of code you'll be able to show an "Add to My Foursquare" button or show any user's badges in your site.GetSatisfaction Helper for WebMatrix: The GetSatisfaction Helper for WebMatrix allows you to easily integrate GetSatistaction feedback functionality into your site. It provides a set of widgets for your users to share their ideas, questions, problems, and praises.GoodStore: ??????????，??B/S??，asp.net?sqlserver???，???????，?????????。。。Groupon Helper for WebMatrix: The Groupon Helper for WebMatrix allows you to easily add a Groupon badge to your WebMatrix site. When the helper is in place, it can query the Groupon API to get the deals for a given location, for you to display them in new, different ways. HarrierSight: An extensible application for analyze of spatial dataiPlay: iPlay is a WPF application built using MVVM for generating iTunes playlists randomly and displaying the status of iTunes in a user friendly way. It's secondary purpose is to explore the capabilities of WPF and MVVM in a contextual way.iSun Studio CMS: SNS Kiiro: An easy to use collaboration and project management application built for SharePoint. Kiiro lets your team collaborate on projects, documents, discussions, tasks and issues all within a simple, easy-to-use interface.Kiva7: The Kiva7 app is a Windows Phone 7 app for www.kiva.com. It shows all information on your loans and allows you to search for new loans. LeanEngine Framework: The LeanEngine framework makes it easier and faster for developers to develop .Net data centric applications. It's developed in C# language.MedSpeech: Guardado de grabaciones sobre los estudios radiologicos para luego poder realizar reportes de estos.Open Gran Turismo: Open Gran Turismo is an opensource car racing game highly customizable developed in XNA and BEPU physics. Opt.Net: Command line options and arguments parsing library for .NET 3.5 and 4.0 programs. Uses reflection to convert command line arguments and options into property values on an object that the application defines. Will support command pattern programs as well.Plancast Helper for WebMatrix: The Plancast Helper for WebMatrix provides an easy way to integrate Plancast on your WebMatrix site. With a few lines of code you'll able to show your Plancast plans or the ones from your friends. Polldaddy Helper for WebMatrix: The Polldaddy helper makes easy to add Poll widgets, ratings and surveys to your WebMatrix site in a few lines of code. It also provides access to the Polldaddy API, wrapping some of the API methods to retrieve Poll data.Scribd Helper for WebMatrix: The Scribd Helper for WebMatrix allows you to easily add Scribd documents to your site. When the helper is in place, it interacts with the Scribd API and with Scribd Reader to easily list your documents, enabling users to view them without having to leave your site. SharePoint 2010 Custom List Form Demo: This example will show you how to create a custom list form for SharePoint 2010 in Visual Studio 2010 using SharePoint Designer 2010 and VS2010... See my blog for a "Walkthrough": http://ikarstein.wordpress.comTdd unit test bar for Windows Phone development: a simple application which launches NUnit-Console on your Windows Phone unit tests every time you build, using a SilverLight version of NUnit. The output is then colored for better readability: Green bar if success, Red bar if failure.Techne: Techne is a program which will take a user input of a color or picture and then using motors to pipette paint will manually create the colors described by the user and draw a picture. The goal is to continually expand the system into performing more complicated tasks.TelerikTest1: ????Telerik??111111111TriExporterNET: TriExporter .NET Twitter Helper for WebMatrix: The Twitter Helper for WebMatrix makes it simple to integrate several Twitter social features in your site. For example, you can display Twitter widgets like "Follow Me" and "Tweet" Buttons, and access the Timeline Resources exposed by the Twitter API in a few lines of code.windows azure backup: If you need to have a backup of your files using Windows Azure, then this is the project to download. It incorporates an "admin" user and his backups. Can upload/retrieve files from local hard drive. Made with ASP.NET MVC.WP7PrintHelper: This project is aimed at the Windows Phone 7 developers that need to print from an App they are developing. The project provides a WCF service that runs on any desktop or server, and a print dialog dll that runs on the Windows 7 phone. It is developed in Framework 4.0 Client C#Wufoo Helper for WebMatrix: The Wufoo Helper for WebMatrix provides an easy way to integrate Wufoo forms and data into your WebMatrix site. It allows you to add Wufoo forms in your pages and integrate the data submitted in your forms by using Web Hooks.

  Read the article

• Flot not displaying x axis labels correctly

  - by JVXR

  I have to display a graph with date on the X axis and Amt on the Y axis. There will be 8 lines (series) each with n months data. When I plot the graph I am sending in 6 months data for sure.( one line's data is shown below) [1251701950000, 34.50553] [1254294030000, 27.014463] [1256972350000, 26.7805] [1259567970000, 33.08871] [1262246430000, 51.987762] [1264924750000, 56.868233] However the graph shows up like this http://twitpic.com/1gbb7m The first months label is missing and last month is not aligned correctly, my flot js code is as follows $.plot($("#lgdGraphTab"),graphData, { xaxis: { mode: "time", timeformat: "%b-%y", monthNames: ["Jan", "Feb", "Mar", "Apr", "May", "Jun", "Jul", "Aug", "Sep", "Oct", "Nov", "Dec"], minTickSize: [1, "month"] }, yaxis : { tickSize: 5 }, series: { lines: { show: true , shadowSize:0}, points: { show: true } }, legend:{ container: $('#legendArea'), noColumns:8 }, clickable: true, hoverable: true });

  Read the article

• UITextView adding text to new line

  - by Subro

  I would like to add new lines of text to my UITextView for my iPhone app. Basically my textview starts with a single line, and as app advances, new lines are added. However I can add only to the end or beginning of the existing text. How can I make such an entry into a new line. Can I manually send \n to the textview.text at a calculated range/location. E.g. of what I mean. line 1: This is first line of text. This is second line 2: line of text. --- I want: line 1: This is first line of text. line 2: This is second line of text. Thanks!

  Read the article

• Making mercurial subrepositories behave like subversion externals

  - by Emily Dickinson

  Hi guys, The FAQ, and hginit.com have been really useful for helping me make the transition from svn to hg. However, when it comes to using Hg's subrepository feature in the manner of subversion's externals, I've tried everythign and cannot replicate the nice behavior of svn externals. Here's the simplest example of what I want to do: Init "lib" repository This repository is never to be used as a standalone; it's always included by main repositories, as a sub-repository. Init one or more including repositories To keep the example simple, I'll "init" a repository called "main" Have "main" include "lib" as a subrepository Importantly -- AND HERE'S WHAT I CAN'T GET TO WORK: When I modify a file inside of "main/lib", and I push the modification, then that change gets pushed to the "lib" repository -- NOT to a copy inside of "main". Command lines speak louder than words. I've tried so many variations on this theme, but here's the gist. If someone can reply, in command lines, I'll be forever grateful! 1. Init "lib" repository $ cd /home/moi/hgrepos ## Where I'm storing my hg repositories, on my main server $ hg init lib $ echo "foo" lib/lib.txt $ hg add lib $ hg ci -A -m "Init lib" lib 2. Init "main" repository, and include "lib" as a subrepos $ cd /home/moi/hgrepos $ hg init main $ echo "foo" main/main.txt $ hg add main $ cd main $ hg clone ../lib lib $ echo "lib=lib" .hgsub $ hg ci -A -m "Init main" . This all works fine, but when I make a clone of the "main" repository, and make local modifications to files in "main/lib", and push them, the changes get pushed to "main/lib", NOT to "lib". IN COMMAND-LINE-ESE, THIS IS THE PROBLEM: $ /home/moi/hg-test $ hg clone ssh://[email protected]/hgrepos/lib lib $ hg clone ssh://[email protected]/hgrepos/main main $ cd main $ echo foo lib/lib.txt $ hg st M lib.txt $ hg com -m "Modified lib.txt, from inside the main repos" lib.txt $ hg push pushing to ssh://[email protected]/hgrepos/main/lib That last line of output from hg shows the problem. It shows that I've made a modification to a COPY of a file in lib, NOT to a file in the lib repository. If this were working as I'd like it to work, the push would be to hgrepos/lib, NOT to hgrepos/main/lib. I.e., I would see: $ hg push pushing to ssh://[email protected]/hgrepos/lib IF YOU CAN ANSWER THIS IN TERMS OF COMMAND LINES RATHER THAN IN ENGLISH, I WILL BE ETERNALLY GRATEFUL! Thank you in advance! Emily in Portland

  Read the article

• Floating DIV's alignment problem.

  - by Rodrigo

  I have a fluid layout with DIV's of different heights and widths, and I'd like them to be aligned by lines, kind of like when you do a search on istockphoto, except aligned to the top: image here--http://i207.photobucket.com/albums/bb121/jpbanks/Capturadepantalla2010-06-02alas1902.png I tried floating all the DIV's to the left, but they are not aligned correctly into lines: image here--http://i207.photobucket.com/albums/bb121/jpbanks/Capturadepantalla2010-06-02alas1900.png See how "Prueba" doesn't go all the way to the left? I thought of the jQuery plugin Masonry but what I want is obviously different. Any solution using either CSS or jQuery would be fine. Any ideas?

  Read the article

• RCov started analyzing loaded libs (including Rdoc itself) – when using rvm (Ruby Version Manager)

  - by phvalues

  Context rcov 0.9.8 2010-02-28 ruby 1.8.7 (2009-06-12 patchlevel 174) [i686-darwin10.3.0] rvm 0.1.38 by Wayne E. Seguin ([email protected]) [http://rvm.beginrescueend.com/] System Ruby (rvm use system): ruby 1.8.7 (2010-01-10 patchlevel 249) [i686-darwin10] Files The test setup is a 'lib' folder containing a single file which defines a class, the folders 'test' and 'test/sub_test', with 'sub_test' containing the single 'test_example_lib.rb' and a Rakefile like this: require 'rcov/rcovtask' task :default = [:rcov] desc "RCov" Rcov::RcovTask.new do | t | t.test_files = FileList[ 'test/**/test_*.rb' ] end Result #rake (in /Users/stephan/tmp/rcov_example) rm -r coverage Loaded suite /Users/stephan/.rvm/gems/ruby-1.8.7-p174/bin/rcov Started . Finished in 0.000508 seconds. 1 tests, 2 assertions, 0 failures, 0 errors +----------------------------------------------------+-------+-------+--------+ | File | Lines | LOC | COV | +----------------------------------------------------+-------+-------+--------+ |...ms/rcov-0.9.8/lib/rcov/code_coverage_analyzer.rb | 271 | 156 | 5.1% | |...ems/rcov-0.9.8/lib/rcov/differential_analyzer.rb | 116 | 82 | 9.8% | |lib/example_lib.rb | 16 | 11 | 72.7% | +----------------------------------------------------+-------+-------+--------+ |Total | 403 | 249 | 9.6% | +----------------------------------------------------+-------+-------+--------+ 9.6% 3 file(s) 403 Lines 249 LOC Question Why is RCov itself analysed here? I'd expect that (and it doesn't happen when using 'rvm use system'). In fact it seems to be due to me using a Ruby installed via rvm.

  Read the article

• Eclipse 3.5 switching tab is very slow

  - by n179911

  I am using eclipse 3.5 (cocoa build) on Macos 10.5 with Java 1.5.0.19. I just have 3 java files opened 1 files ~ 2000 lines the other 2 are ~ 700 lines. But when I switch from 1 file tab to another, eclipse takes a long time (~ 20 seconds) to switch to another tab. I have already change the eclipse.ini to more eclipse.ini -startup ../../../plugins/org.eclipse.equinox.launcher_1.0.200.v20090520.jar --launcher.library ../../../plugins/org.eclipse.equinox.launcher.cocoa.macosx_1.0.0.v20090519 -product org.eclipse.epp.package.jee.product -showsplash org.eclipse.platform --launcher.XXMaxPermSize 256m -vmargs -Dosgi.requiredJavaVersion=1.5 -XstartOnFirstThread -Dorg.eclipse.swt.internal.carbon.smallFonts -XX:MaxPermSize=512m -Xms128m -Xmx1024m -Xdock:icon=../Resources/Eclipse.icns -XstartOnFirstThread -Dorg.eclipse.swt.internal.carbon.smallFonts Is there any way to make eclipse 3.5 more speedy? Thank you.

  Read the article

< Previous Page | 52 53 54 55 56 57 58 59 60 61 62 63  | Next Page >