Search Results

Search found 2911 results on 117 pages for 'payment gateway'.

Page 56/117 | < Previous Page | 52 53 54 55 56 57 58 59 60 61 62 63  | Next Page >

  • VPN iptables Forwarding: Net-to-net

    - by Mike Holler
    I've tried to look elsewhere on this site but I couldn't find anything matching this problem. Right now I have an ipsec tunnel open between our local network and a remote network. Currently, the local box running Openswan ipsec with the tunnel open can ping the remote ipsec box and any of the other computers in the remote network. When logged into on of the remote computers, I can ping any box in our local network. That's what works, this is what doesn't: I can't ping any of the remote computers via a local machine that is not the ipsec box. Here's a diagram of our network: [local ipsec box] ----------\ \ [arbitrary local computer] --[local gateway/router] -- [internet] -- [remote ipsec box] -- [arbitrary remote computer] The local ipsec box and the arbitrary local computer have no direct contact, instead they communicate through the gateway/router. The router has been set up to forward requests from local computers for the remote subnet to the ipsec box. This works. The problem is the ipsec box doesn't forward anything. Whenever an arbitrary local computer pings something on the remote subnet, this is the response: [user@localhost ~]# ping 172.16.53.12 PING 172.16.53.12 (172.16.53.12) 56(84) bytes of data. From 10.31.14.16 icmp_seq=1 Destination Host Prohibited From 10.31.14.16 icmp_seq=2 Destination Host Prohibited From 10.31.14.16 icmp_seq=3 Destination Host Prohibited Here's the traceroute: [root@localhost ~]# traceroute 172.16.53.12 traceroute to 172.16.53.12 (172.16.53.12), 30 hops max, 60 byte packets 1 router.address.net (10.31.14.1) 0.374 ms 0.566 ms 0.651 ms 2 10.31.14.16 (10.31.14.16) 2.068 ms 2.081 ms 2.100 ms 3 10.31.14.16 (10.31.14.16) 2.132 ms !X 2.272 ms !X 2.312 ms !X That's the IP for our ipsec box it's reaching, but it's not being forwarded. On the IPSec box I have enabled IP Forwarding in /etc/sysctl.conf net.ipv4.ip_forward = 1 And I have tried to set up IPTables to forward: *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [759:71213] -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -p icmp -j ACCEPT -A INPUT -i lo -j ACCEPT -A INPUT -p tcp -m state --state NEW -m tcp --dport 22 -j ACCEPT -A INPUT -p tcp -m state --state NEW -m tcp --dport 25 -j ACCEPT -A INPUT -p udp -m state --state NEW -m udp --dport 500 -j ACCEPT -A INPUT -p udp -m state --state NEW -m udp --dport 4500 -j ACCEPT -A INPUT -m policy --dir in --pol ipsec -j ACCEPT -A INPUT -p esp -j ACCEPT -A INPUT -j REJECT --reject-with icmp-host-prohibited -A FORWARD -s 10.31.14.0/24 -d 172.16.53.0/24 -j ACCEPT -A FORWARD -m policy --dir in --pol ipsec -j ACCEPT -A FORWARD -j REJECT --reject-with icmp-host-prohibited COMMIT Am I missing a rule in IPTables? Is there something I forgot? NOTE: All the machines are running CentOS 6.x Edit: Note 2: eth1 is the only network interface on the local ipsec box.

    Read the article

  • eth0:0 is configured but not listed in ifconfig output

    - by FractalizeR
    Hello. I have the following problem: My server was given two IPs from [b]different[/b] subnets. Now I am trying to configure the system to work properly. I have created [root@server ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth0 # Intel Corporation 80003ES2LAN Gigabit Ethernet Controller (Copper) HWADDR=00:30:48:DA:B1:0E DEVICE=eth0 BOOTPROTO=none BROADCAST=79.174.69.255 IPADDR=79.174.69.241 NETMASK=255.255.254.0 NETWORK=79.174.68.0 ONBOOT=yes GATEWAY=79.174.68.1 TYPE=Ethernet [root@server ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth0:0 # Intel Corporation 80003ES2LAN Gigabit Ethernet Controller (Copper) HWADDR=00:30:48:DA:B1:0E DEVICE=eth0 BOOTPROTO=none BROADCAST=79.174.69.255 IPADDR=79.174.71.74 NETMASK=255.255.255.0 NETWORK=79.174.71.1 ONBOOT=yes GATEWAY=79.174.71.1 TYPE=Ethernet But both after "service network restart" and after "reboot" [root@server ~]# ifconfig eth0 Link encap:Ethernet HWaddr 00:30:48:DA:B1:0E inet addr:79.174.71.74 Bcast:79.174.71.255 Mask:255.255.255.0 inet6 addr: fe80::230:48ff:feda:b10e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:910284 errors:0 dropped:0 overruns:0 frame:0 TX packets:2924 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:257964879 (246.0 MiB) TX bytes:232450 (227.0 KiB) Memory:df220000-df240000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:27 errors:0 dropped:0 overruns:0 frame:0 TX packets:27 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6976 (6.8 KiB) TX bytes:6976 (6.8 KiB) Device eth0:0 is not shown as active. If I try [root@server ~]# ifconfig eth0:0 eth0:0 Link encap:Ethernet HWaddr 00:30:48:DA:B1:0E UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:df220000-df240000 It is shown as up and running, but IP is not assigned to it. Also it is strange, that IP address assigned to eth0:0 in config file is used by eth0. /var/log/messages shows nothing about network configuration errors on either eth0 or eth0:0. system-config-network seem to understand all settings correctly and resaves them ok also. "ifup eth0:0" executes ok, but ifconfig afterwards shows no eth0:0 device after that. What did I do wrong? May be the problem is that IPs are from different subnets?

    Read the article

  • Ping "replies" from same computer with 'Destination host unreachable' (no route to other computer)

    - by Srekel
    I've got two computers in a LAN behind a wireless router. One has XP with ip 192.168.1.2 This one has W7 with ip 192.168.1.7 If I try to ping the other one from this computer, I get this: C:\Users\Srekel>ping 192.168.1.2 Pinging 192.168.1.2 with 32 bytes of data: Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Ping statistics for 192.168.1.2: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Tracert gives the same result: C:\Users\Srekel>tracert 192.168.1.2 Tracing route to 192.168.1.2 over a maximum of 30 hops 1 Kakburken4 [192.168.1.7] reports: Destination host unreachable. Trace complete. Although I can ping and tracert the router without any problems. I have disabled the firewalls on both computers. The router is set to use DHCP (if that matters). Here is the output from "route". C:\Users\Srekel>route print =========================================================================== Interface List 13...00 25 86 df c6 89 ......TP-LINK Wireless N Adapter 12...e0 cb 4e 26 b9 84 ......Realtek PCIe GBE Family Controller #2 11...e0 cb 4e 26 be 94 ......Realtek PCIe GBE Family Controller 1...........................Software Loopback Interface 1 16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 14...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.7 20 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.1.0 255.255.255.0 On-link 192.168.1.7 276 192.168.1.7 255.255.255.255 On-link 192.168.1.7 276 192.168.1.255 255.255.255.255 On-link 192.168.1.7 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.7 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.7 276 =========================================================================== Persistent Routes: None IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 14 58 ::/0 On-link 1 306 ::1/128 On-link 14 58 2001::/32 On-link 14 306 2001:0:5ef5:73ba:881:20c1:3f57:fef8/128 On-link 14 306 fe80::/64 On-link 14 306 fe80::881:20c1:3f57:fef8/128 On-link 1 306 ff00::/8 On-link 14 306 ff00::/8 On-link =========================================================================== Persistent Routes: None I've set up and debugged a few networks in my life but I'm not really an advanced network user, so I'm not sure what might be wrong. Any ideas? Oh, and pinging this computer from the other computer doesn't work either.

    Read the article

  • configure squid with windows 2008

    - by G.a.r.y.
    Hi my problem is this: I have a 3 pc (192.168.1.2,..3,..4) and a windows 2008 server (192.168.1.100) router is 192.168.1.1. I just want that the 3 pc set like gateway 192.168.1.100, are filter by squid proxy loaded in win2008 so in win2008 I 've set in control panel the proxy 192.168.1.100:3128 and in win2008 browser work, the connection is filtered by proxy, but in 3 pc not works, so maybe I should route all incoming request into squid, but I dunno how ... thanks

    Read the article

  • ISA Server 2006 SP1 :: Allow unauthenticated users (non domain users) access to external (internet)

    - by Klaptrap
    Now that we have applied an internal to external rule blocking all users access to the internet, other than those users in a whitelist, we have the obvious issue of non authenticated users, not on our domain, i.e.; domain-less guests not being able to access the internet. Other than configuring each machine to use our alternative gateway - which would require a member of IT to be onsite everytime a guest arrives - can this be done through ISA adn AD?

    Read the article

  • Error loading Mongrel in Aptana Ruby Application on Vista

    - by floatingfrisbee
    I'm brand new at Ruby. Trying to set up the first application/project using Aptana Studio. Here are my ruby and gem versions c:\>ruby -v ruby 1.9.1p378 (2010-01-10 revision 26273) [i386-mingw32] c:\>gem -v 1.3.6 I am seeing this error below while starting my ruby application. I'm developing on Vista (sucks, I know but am working on changing that) C:/Ruby/lib/ruby/gems/1.9.1/gems/activesupport-2.3.4/lib/active_support/dependencies.rb:156:in `require': 126: The specified module could not be found. - C:/Ruby/lib/ruby/gems/1.9.1/gems/mongrel-1.1.5-x86-mingw32/lib/http11.so (LoadError) from C:/Ruby/lib/ruby/gems/1.9.1/gems/activesupport-2.3.4/lib/active_support/dependencies.rb:156:in `block in require' from C:/Ruby/lib/ruby/gems/1.9.1/gems/activesupport-2.3.4/lib/active_support/dependencies.rb:521:in `new_constants_in' from C:/Ruby/lib/ruby/gems/1.9.1/gems/activesupport-2.3.4/lib/active_support/dependencies.rb:156:in `require' from C:/Ruby/lib/ruby/gems/1.9.1/gems/mongrel-1.1.5-x86-mingw32/lib/mongrel.rb:12:in `<top (required)>' from C:/Ruby/lib/ruby/gems/1.9.1/gems/activesupport-2.3.4/lib/active_support/dependencies.rb:156:in `require' from C:/Ruby/lib/ruby/gems/1.9.1/gems/activesupport-2.3.4/lib/active_support/dependencies.rb:156:in `block in require' from C:/Ruby/lib/ruby/gems/1.9.1/gems/activesupport-2.3.4/lib/active_support/dependencies.rb:521:in `new_constants_in' from C:/Ruby/lib/ruby/gems/1.9.1/gems/activesupport-2.3.4/lib/active_support/dependencies.rb:156:in `require' from C:/Ruby/lib/ruby/gems/1.9.1/gems/rack-1.0.0/lib/rack/handler/mongrel.rb:1:in `<top (required)>' from C:/Ruby/lib/ruby/gems/1.9.1/gems/rack-1.0.0/lib/rack/handler.rb:17:in `const_get' from C:/Ruby/lib/ruby/gems/1.9.1/gems/rack-1.0.0/lib/rack/handler.rb:17:in `block in get' from C:/Ruby/lib/ruby/gems/1.9.1/gems/rack-1.0.0/lib/rack/handler.rb:17:in `each' from C:/Ruby/lib/ruby/gems/1.9.1/gems/rack-1.0.0/lib/rack/handler.rb:17:in `get' from C:/Ruby/lib/ruby/gems/1.9.1/gems/rails-2.3.4/lib/commands/server.rb:45:in `<top (required)>' from C:/Users/Me - Admin/My Documents/Aptana RadRails Workspace/EventBuzz/script/server:3:in `require' from C:/Users/Me - Admin/My Documents/Aptana RadRails Workspace/EventBuzz/script/server:3:in `<top (required)>' from -e:2:in `load' from -e:2:in `<main>' As a part of fixing this issue, I've installed the following gems and updates c:\>gem update --system Updating RubyGems Nothing to update c:\>gem install rails capistrano mongrel mongrel_cluster Successfully installed rails-2.3.5 Successfully installed net-ssh-2.0.21 Successfully installed net-sftp-2.0.4 Successfully installed net-scp-1.0.2 Successfully installed net-ssh-gateway-1.0.1 Successfully installed highline-1.5.2 Successfully installed capistrano-2.5.18 Successfully installed mongrel-1.1.5-x86-mingw32 Successfully installed mongrel_cluster-1.0.5 9 gems installed Installing ri documentation for rails-2.3.5... Installing ri documentation for net-ssh-2.0.21... Installing ri documentation for net-sftp-2.0.4... Installing ri documentation for net-scp-1.0.2... Installing ri documentation for net-ssh-gateway-1.0.1... Installing ri documentation for highline-1.5.2... Installing ri documentation for capistrano-2.5.18... Installing ri documentation for mongrel-1.1.5-x86-mingw32... Installing ri documentation for mongrel_cluster-1.0.5... Updating class cache with 1380 classes... Installing RDoc documentation for rails-2.3.5... Installing RDoc documentation for net-ssh-2.0.21... Installing RDoc documentation for net-sftp-2.0.4... Installing RDoc documentation for net-scp-1.0.2... Installing RDoc documentation for net-ssh-gateway-1.0.1... Installing RDoc documentation for highline-1.5.2... Installing RDoc documentation for capistrano-2.5.18... Installing RDoc documentation for mongrel-1.1.5-x86-mingw32... Installing RDoc documentation for mongrel_cluster-1.0.5... c:\>gem install mysql Successfully installed mysql-2.8.1-x86-mingw32 1 gem installed Installing ri documentation for mysql-2.8.1-x86-mingw32... Updating class cache with 1641 classes... Installing RDoc documentation for mysql-2.8.1-x86-mingw32... Ideas as to what is going on?

    Read the article

  • Windows server RAS VPN client can't connect to internet

    - by Dragouf
    I configured a windows server 2008 RAS to connect automatically to a pptp vpn server. Problem is that when it connect I can't access internet from this server (the vpn client connect through RAS) Usually I ask vpn not to be use as the default gateway but this part is disable int the network interface - VPN interface properties : And I don't find how to ask to connect to internet directly....

    Read the article

  • Help with router and spotty wireless...

    - by Moshe
    Time Warner Cable/ Road Runner router shows up some times on the network list on Mac OS X 10.6.3 Snow Leopard. It makes a spotty appearence on the list. The router is a SMC Networks Model # SMC8014WG-SI. The default gateway numbers all do not work. 192.168.0.1 192.168.1.1 192.168.2.1 10.10.10.1 What IP adress am I looking for here to log in to the router to fix the issue?

    Read the article

  • Laptop LCD sometimes stops working on reboot. Please help.

    - by J Ringle
    I have a Gateway P-6831FX Laptop with Vista Ultimate. The Laptop LCD will sometimes not come on after I reboot the computer. I don't even close the lid and it happens. It isn't dim, it doesn't come on at all. No posting of CMOS (BIOS), nothing. Please note... this happens sometimes, not every time. Frustrating! When plugged into an external monitor, which works fine, Vista display properties can't even "sense" the laptop LCD. I try to enable the laptop LCD for dual display, turning on the laptop LCD, and it does nothing. It's like the laptop LCD is not even there. Manually taking a magnet in my hand to the laptop lid sensing switch (the sensor that turns off display/sleep mode when you close lid), sometimes causes the LCD backlight to "turn on" but not display any images. By "turn on" I mean I can see the screen backlight turn on to a 'dark gray' screen instead of pitch black. Subsequent reboot the laptop display is not working again! Here are the facts: Only happens at random and only after a reboot. Waking from Sleep mode isn't a problem. Pressing F4 function key for dual display does nothing when this happens. Closing lid doesn't seem to be related. (unless it is only after reboot.) using external magnet from laptop screen sensor sometimes triggers backlight to turn on but reboot back to square one with no LCD display. an external display always works fine. I have taken apart LCD, checked all wires and ribbons for loose connections or damage. I have replaced the Inverter. It doesn't seem to be heat related as I can put in sleep mode and resume fine when very hot. (external monitor works fine too). Sometimes the screen works fine as if there is not a problem at all. Even after a reboot... This is random. Any ideas out there? If it is a bad part... which one? The LCD seems to be fine. What are the odds of 2 bad inverters? The backlight is fine. The LCD wires/ribbons seem to be fine. I am at a loss. No warranty left and Gateway tech support is clueless. Thanks for any feedback that might help.

    Read the article

  • Two network adapters on Ubuntu Server 9.10 - Can't have both working at once?

    - by Rob
    I'm trying to set up two network adapters in Ubuntu (server edition) 9.10. One for the public internet, the other a private LAN. During the install, I was asked to pick a primary network adapter (eth0 or eth1). I chose eth0, gave the installer the details listed below in the contents of /etc/network/interfaces, and carried on. I've been using this adapter with these setting for the last few days, and every thing's been fine. Today, I decide it's time to set up the local adapter. I edit the /etc/network/interfaces to add the details for eth1 (see below), and restart networking with sudo /etc/init.d/networking restart. After this, attempting to ping the machine using it's external IP address fails, but I can ping it's local IP address. If I bring eth1 down using sudo ifdown eth1, I can successfully ping the machine via it's external IP address again (but obviously not it's internal IP address). Bringing eth1 back up returns us to the original problem state: external IP not working, internal IP working. Here's my /etc/network/interfaces (I've removed the external IP information, but these settings are unchanged from when it worked) rob@rhea:~$ cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary (public) network interface auto eth0 iface eth0 inet static address xxx.xxx.xxx.xxx netmask xxx.xxx.xxx.xxx network xxx.xxx.xxx.xxx broadcast xxx.xxx.xxx.xxx gateway xxx.xxx.xxx.xxx # The secondary (private) network interface auto eth1 iface eth1 inet static address 192.168.99.4 netmask 255.255.255.0 network 192.168.99.0 broadcast 192.168.99.255 gateway 192.168.99.254 I then do this: rob@rhea:~$ sudo /etc/init.d/networking restart * Reconfiguring network interfaces... [ OK ] rob@rhea:~$ sudo ifup eth0 ifup: interface eth0 already configured rob@rhea:~$ sudo ifup eth1 ifup: interface eth1 already configured Then, from another machine: C:\Documents and Settings\Rob>ping [external ip] Pinging [external ip] with 32 bytes of data: Request timed out. Request timed out. Request timed out. Request timed out. Ping statistics for [external ip]: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), Back on the Ubuntu server in question: rob@rhea:~$ sudo ifdown eth1 ... and again on the other machine: C:\Documents and Settings\Rob>ping [external ip] Pinging [external ip] with 32 bytes of data: Reply from [external ip]: bytes=32 time<1ms TTL=63 Reply from [external ip]: bytes=32 time<1ms TTL=63 Reply from [external ip]: bytes=32 time<1ms TTL=63 Reply from [external ip]: bytes=32 time<1ms TTL=63 Ping statistics for [external ip]: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms So... what am I doing wrong?

    Read the article

  • How to transition to Comcast with static IP address

    - by steveha
    I have my own email server in my house, on a static IP address. I have had business DSL for over a decade, but I also now have Comcast business Internet. I want to transition from the DSL to the Comcast, and I have some questions. I have a domain name, my own mail server, and a firewall (a PC with two network interfaces, running Devil-Linux). I need to make sure I understand how to set up the Comcast cable box, and how to set up my firewall. First, do I need to change any settings in the cable box? Currently I have only used the cable box by plugging in a laptop, with the laptop doing DHCP. I think I can leave the box alone but I would like to make sure. Second, I'm not sure I understand the instructions Comcast gave me for setting up the firewall. My DSL provider gave me the following information: static IP address, net mask, gateway, and two DNS servers. Comcast gave me: static IP address, routable static IP address, net mask, and two DNS servers, and told me to put the "static IP address" as the "gateway" on the firewall. Is this just Comcast-speak here? Does "routable static IP address" mean the same thing as "static IP address" in my DSL setup, the end-point address that I should publish in the DNS MX records for my email server? Or should I publish the "static IP address", and Comcast will then route all its traffic over the cable box? My plan is: first, I'm going to configure another firewall, so I have one firewall for the DSL and one for the Comcast (rather than madly editing settings to switch back and forth). Then I will publish the new Comcast static IP address as a backup email server address in the DNS MX records, wait a while to let it propagate, and then switch my home over from the DSL to the Comcast. Then I'll change DNS to make that the primary mail address and the DSL the secondary, let that go a while and make sure it seems reliable. Then I'll remove the DSL from the DNS MX records completely, and finally shut down the DSL service. (I thought about keeping the DSL as a backup, but the reason I'm leaving DSL is that it has become unreliable; and I have heard that Comcast business Internet is reliable.) Final question, any advice for me? Anything you think might be useful, helpful, or educational. Thanks.

    Read the article

  • Setup VPN access on a windows dedicated server for browsing

    - by Pasta
    I have a dedicated windows server. I want to create a VPN to encrypt my traffic (browsing, IM, etc) as I browse on my laptop using public wifi networks. What keywords should I be using to search Google? Are there any resources that help me do this? Most of the solutions are just to encrypt communication between the server to a machine. It does not act like an internet gateway, etc.

    Read the article

  • How to transition to Comcast with static IP address [migrated]

    - by steveha
    I have my own email server in my house, on a static IP address. I have had business DSL for over a decade, but I also now have Comcast business Internet. I want to transition from the DSL to the Comcast, and I have some questions. I have a domain name, my own mail server, and a firewall (a PC with two network interfaces, running Devil-Linux). I need to make sure I understand how to set up the Comcast cable box, and how to set up my firewall. First, do I need to change any settings in the cable box? Currently I have only used the cable box by plugging in a laptop, with the laptop doing DHCP. I think I can leave the box alone but I would like to make sure. Second, I'm not sure I understand the instructions Comcast gave me for setting up the firewall. My DSL provider gave me the following information: static IP address, net mask, gateway, and two DNS servers. Comcast gave me: static IP address, routable static IP address, net mask, and two DNS servers, and told me to put the "static IP address" as the "gateway" on the firewall. Is this just Comcast-speak here? Does "routable static IP address" mean the same thing as "static IP address" in my DSL setup, the end-point address that I should publish in the DNS MX records for my email server? Or should I publish the "static IP address", and Comcast will then route all its traffic over the cable box? My plan is: first, I'm going to configure another firewall, so I have one firewall for the DSL and one for the Comcast (rather than madly editing settings to switch back and forth). Then I will publish the new Comcast static IP address as a backup email server address in the DNS MX records, wait a while to let it propagate, and then switch my home over from the DSL to the Comcast. Then I'll change DNS to make that the primary mail address and the DSL the secondary, let that go a while and make sure it seems reliable. Then I'll remove the DSL from the DNS MX records completely, and finally shut down the DSL service. (I thought about keeping the DSL as a backup, but the reason I'm leaving DSL is that it has become unreliable; and I have heard that Comcast business Internet is reliable.) Final question, any advice for me? Anything you think might be useful, helpful, or educational. Thanks.

    Read the article

  • SSH port forwarding through Windows machine

    - by Leonardo Ramé
    is it possible to connect to an SSH server only accessible from inside a network, using a Windows machine without SSH as a gateway?. Let me clarify my question with a sketch: Me (Linux machine)--- WIN (Windows without SSHD)---LIN (Linux with SSHD). Machine Me, is the PC I'm using to connect to LIN through WIN. WIN is accessible from the outside, it has an RDESKTOP port open, and LIN is only accessible from inside the network. Hope you understand the question.

    Read the article

  • Connectivity issues with dual NIC machine in EC2

    - by Matt Sieker
    I'm trying to get some servers set up in EC2 in a Virtual Private Cloud. To do this, I have two subnets: 10.0.42.0/24 - Public subnet 10.0.83.0/24 - Private subnet To bridge these two, I have a Funtoo instance with a pair of NICs: eth0 10.0.42.10 eth1 10.0.83.10 Which has the following routing table: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.0.83.0 * 255.255.255.0 U 0 0 0 eth1 10.0.83.0 * 255.255.255.0 U 203 0 0 eth1 10.0.42.0 * 255.255.255.0 U 202 0 0 eth0 loopback * 255.0.0.0 U 0 0 0 lo default 10.0.42.1 0.0.0.0 UG 0 0 0 eth0 default 10.0.42.1 0.0.0.0 UG 202 0 0 eth0 An elastic IP is attached to the eth0 interface, and I can connect to it fine remotely. However, I cannot ping anything in the 10.0.83.0 subnet. For now iptables is not set up on the box, so there's no rules that would get in the way (Eventually this will be managed by Shorewall, but I should get basic connectivity done first) Subnet details from the VPC interface: CIDR: 10.0.83.0/24 Destination Target 10.0.0.0/16 local 0.0.0.0/0 [ID of eth1 on NAT box] Network ACL: Default Inbound: Rule # Port (Service) Protocol Source Allow/Deny 100 ALL ALL 0.0.0.0/0 ALLOW * ALL ALL 0.0.0.0/0 DENY Outbound: Rule # Port (Service) Protocol Destination Allow/Deny 100 ALL ALL 0.0.0.0/0 ALLOW * ALL ALL 0.0.0.0/0 DENY   CIDR: 10.0.83.0/24 VPC: Destination Target 10.0.0.0/16 local 0.0.0.0/0 [Internet Gateway ID] Network ACL: Default (replace) Inbound: Rule # Port (Service) Protocol Source Allow/Deny 100 ALL ALL 0.0.0.0/0 ALLOW * ALL ALL 0.0.0.0/0 DENY Outbound: Rule # Port (Service) Protocol Destination Allow/Deny 100 ALL ALL 0.0.0.0/0 ALLOW * ALL ALL 0.0.0.0/0 DENY I've been trying to work this out most of the evening, but I'm just stuck. I'm either missing something obvious, or am doing something very wrong. I would think I'd be able to ping from either interface on this box without issue. Hopefully some more pairs of eyes on this configuration will help. EDIT: I am an idiot. After I bothered to install nmap to run some more tests, I discover I can see the ports, and connect to them, pings are just being blocked.

    Read the article

  • Restrict VPN client traffic to certain domains/IP

    - by mr-euro
    Hi Is there any way to restrict a VPN client to only route certain traffic via the VPN and the rest via their local gateway? For example: traffic to a certain IP or domain gets routed across the VPN and all other requests do not. Let me know if you need more details. Thank you.

    Read the article

  • Issues with static IP (Ubuntu Server 10.04)

    - by letseatfood
    I am following this tutorial for setting up a testing server for my web development projects. When I attempt setting up a static IP address (using the configuration below), I receive the error "ping: unknown host www.google.com" when I attempt using ping. auto eth0 iface eth0 inet static address 192.168.0.100 netmask 255.255.255.0 network 192.168.0.0 broadcast 192.168.0.255 gateway 192.168.0.1 Ping works fine when the configuration is: auto eth0 iface eth0 inet static I am a novice to server setup and administration.

    Read the article

  • How to connect FortiGate1 SSL VPN remote access from Fedora/CentOS/Ubuntu Linux?

    - by YumYumYum
    How can i connect to FortiGate1 SSL VPN Remote Access router from Fedora/CentOS or Ubuntu/Debian? It only working with Windows Internet explorer for the moment using Vbox (But i cant use Windows only for this) How can i use it from my favourate Linux? # vpnc Enter IPSec gateway address: xx.xx.xx.42 Enter IPSec ID for xx.xx.xx.42: Enter IPSec secret for @xx.xx.xx.42: Enter username for xx.xx.xx.42: Myusername Enter password for [email protected]: vpnc: no response from target

    Read the article

  • Why is my router not routing?

    - by dwj
    Starting a week and half ago my router stopped working with my cable modem. I went to sleep with it working and woke up with it not. I swapped in another router and am still having issues; I was gone for 10 days so now I'm back to trying to figure it out. While I was gone I left everything (cable modem, router, and computer) powered off. My setup: Comcast Ambit cable modem (from Comcast) Netgear WGR614 v4 router -- replaced with Linksys WRT54GS v1.1 Windows XP SP3 other computers, all currently unplugged The modem is using the firmware (ver 2.105.2001) provided by Comcast; hardware version 1.3 The Linksys router is using FW ver 4.71.4 (latest for this release of HW), factory defaults I am only using the wired connections; no wireless. I have swapped out all of the cat5 cable. If I plug my computer directly into the cable modem, I can ping by name or number. Everything works perfectly. If I plug my computer into the router and the router into the modem, I cannot access anything outside of my local network. This is the exact setup I've used for the past 5 years; there were no changes in the past year. Now here's the interesting part: I can log into the Linksys router and get status information from it; everything appears good. Using the Diagnostics, I can run ping and traceroute to any site on the internet. These work perfectly. From my computer, I can ping the router and the modem. However, I cannot ping anything on the internet by with name or number. If I plug in another computer, I can ping it successfully. I've included two transcripts below that show these two attempts. Addresses, DNS, gateways, etc. look good. I cannot access the internet through either router. I am at a loss here. Suggestions? Help! Computer to Router to Cable Modem C:\ipconfig /renew Windows IP Configuration No operation can be performed on Bluetooth Network while it has its media disconnected. Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : hsd1.ca.comcast.net. IP Address. . . . . . . . . . . . : 192.168.1.100 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.1 Ethernet adapter Bluetooth Network: Media State . . . . . . . . . . . : Media disconnected C:\ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : wynton Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Unknown IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : hsd1.ca.comcast.net. Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : hsd1.ca.comcast.net. Description . . . . . . . . . . . : Intel(R) 82562V-2 10/100 Network Connection Physical Address. . . . . . . . . : 00-1D-09-9B-45-EB Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.1.100 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 68.87.76.178 68.87.78.130 Lease Obtained. . . . . . . . . . : Monday, March 22, 2010 10:21:55 PM Lease Expires . . . . . . . . . . : Tuesday, March 23, 2010 10:21:55 PM Ethernet adapter Bluetooth Network: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Bluetooth LAN Access Server Driver Physical Address. . . . . . . . . : 00-0A-3A-6F-68-41 C:\ping google.com Ping request could not find host google.com. Please check the name and try again . C:\ping 74.125.19.104 Pinging 74.125.19.104 with 32 bytes of data: Request timed out. Request timed out. Request timed out. Request timed out. Ping statistics for 74.125.19.104: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), C:\ Computer to Cable Modem Directly C:\ipconfig /renew Windows IP Configuration No operation can be performed on Bluetooth Network while it has its media disconnected. Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : hsd1.ca.comcast.net. IP Address. . . . . . . . . . . . : 71.204.149.195 Subnet Mask . . . . . . . . . . . : 255.255.252.0 Default Gateway . . . . . . . . . : 71.204.148.1 Ethernet adapter Bluetooth Network: Media State . . . . . . . . . . . : Media disconnected C:\ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : wynton Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Unknown IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : hsd1.ca.comcast.net. Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : hsd1.ca.comcast.net. Description . . . . . . . . . . . : Intel(R) 82562V-2 10/100 Network Connection Physical Address. . . . . . . . . : 00-1D-09-9B-45-EB Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 71.204.149.195 Subnet Mask . . . . . . . . . . . : 255.255.252.0 Default Gateway . . . . . . . . . : 71.204.148.1 DHCP Server . . . . . . . . . . . : 68.87.76.10 DNS Servers . . . . . . . . . . . : 68.87.76.178 68.87.78.130 Lease Obtained. . . . . . . . . . : Monday, March 22, 2010 10:18:50 PM Lease Expires . . . . . . . . . . : Monday, March 22, 2010 11:12:31 PM Ethernet adapter Bluetooth Network: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Bluetooth LAN Access Server Driver Physical Address. . . . . . . . . : 00-0A-3A-6F-68-41 C:\ping google.com Pinging google.com [74.125.19.99] with 32 bytes of data: Reply from 74.125.19.99: bytes=32 time=20ms TTL=55 Reply from 74.125.19.99: bytes=32 time=17ms TTL=55 Reply from 74.125.19.99: bytes=32 time=28ms TTL=55 Reply from 74.125.19.99: bytes=32 time=18ms TTL=55 Ping statistics for 74.125.19.99: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 17ms, Maximum = 28ms, Average = 20ms C:\ping 74.125.19.104 Pinging 74.125.19.104 with 32 bytes of data: Reply from 74.125.19.104: bytes=32 time=18ms TTL=55 Reply from 74.125.19.104: bytes=32 time=18ms TTL=55 Reply from 74.125.19.104: bytes=32 time=17ms TTL=55 Reply from 74.125.19.104: bytes=32 time=16ms TTL=55 Ping statistics for 74.125.19.104: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 16ms, Maximum = 18ms, Average = 17ms C:\

    Read the article

  • Cisco VPN stops Windows 7 Browsing

    - by Sharjeel Sayed
    My browsing and other 'internet' activity (dropbox,digsby etc) halts when I connect to my office VPN using Cisco Systems VPN client Version 5.0.04.0300 on my Windows 7 Ultimate.The only option left for me at this time is to use my office proxy to enable the connection back. I tried doing the ucheck "Use default gateway on remote network" solution as mentioned on a previous post Windows 7 VPN stops web browser but I don't see that option on the properties of "Cisco systems VPN adapter" connection properties. Here is the screenshot

    Read the article

  • Layer 3 switch routing

    - by Yoshiwaan
    I need help moving over to using our layer 3 switch as the inter vlan routing device rather than our cisco router. I've mostly got it working but I've got stuck near the end and need some advice (I think I just need a bit of education on the subject really). Cur I have a Dell PowerConnect 7048 connecting to a Cisco 1841 router. I've got a few key excerpts from the configs to provide the key information. On the powerconnect I have the following: ip routing ip default-gateway 172.31.14.1 ip route 0.0.0.0 0.0.0.0 172.31.14.1 253 ! interface vlan 1 ip address 172.31.14.254 255.255.255.0 exit interface vlan 2 ip address 172.31.19.254 255.255.255.0 exit interface vlan 4 ip address 172.31.16.254 255.255.255.0 ! interface Gi1/0/1 description 'Link to L7Router01' switchport mode trunk switchport trunk allowed vlan except 3,7-4093 exit ! and on the Cisco the following: interface FastEthernet0/0 ip address 172.31.14.1 255.255.255.0 ip nat inside ip virtual-reassembly ! interface FastEthernet0/0.2 description Accounts VLAN encapsulation dot1Q 2 ip address 172.31.19.1 255.255.255.0 ip nat inside ip virtual-reassembly ! interface FastEthernet0/0.4 description Voice VLAN encapsulation dot1Q 4 ip address 172.31.16.1 255.255.255.0 ip nat inside ip virtual-reassembly ! So what I'm doing is moving clients over so that their default gateway is a 172.31.x.254 address rather than a 172.31.x.1 address. This works great for inter-vlan routing, I have no issues with this. The switch can also access the router no worries, and users on the 172.31.14.0/24 network can access all interfaces and sub-interfaces on the router, including 172.31.14.1. They can also access all of the interfaces that the router connects off to, no worries there. The problem I have is that users on the 172.31.16.0/24 and 172.31.19.0/24 subnets cannot access either 172.31.14.1 or any of the subnets the router connects to. They can, however, connect to BOTH of the sub interfaces on the router from either subnet. What am I missing here? Why can't the vlans connect to the non-sub interface on the router? Are tagged packets being sent to this interface?

    Read the article

  • Transparent Squid : Logging client ip problem

    - by llazzaro
    Hello, I am using the following rules in iptables in my network to use a transparent proxy * iptables -t nat -A PREROUTING -i eth0 -s ! squid-box -p tcp --dport 80 -j DNAT --to squid-box:3128 * iptables -t nat -A POSTROUTING -o eth0 -s local-network -d squid-box -j SNAT --to iptables-box * iptables -A FORWARD -s local-network -d squid-box -i eth0 -o eth0 -p tcp --dport 3128 -j ACCEPT But my squid log, always logs gateway IP (172.16.0.1) Do you know an alternative to not lose client IP? (of course avoid saing manual proxy setup!)

    Read the article

  • Windows 7 crashes with a blue screen

    - by Chinook pilot
    I am running win 7 32 bit on a Gateway Media Center. Without any interaction from me, and the only thing on the screen is my screen saver it crashes and the fault is "Stop" and a long string of numbers. I have had a "adapi sys message but now it seems to be this "Stop' MESSAGE. Any help will be appreciated.

    Read the article

  • FTP could not connect after applying local DNS(private DNS)

    - by Rahul
    I made a software router in CentOS linux and in that made a DNS server. I am using centOS 6..4 for making DNS i applied following steps: changed the host name = abc.zoom.com and domain name = zoom.com. then did changes in the named.rfc.1912 file as per rename named.localhost = forward and named.loopback = reverse in forward lookups i changed zone "zoom.com" IN { type master; file "forward"; allow-update { none; }; and in reverse lookups i changed zone "x.168.192.in-addr.arpa" IN { type master; file "reverse"; allow-update { none; }; and then did changes in the named.conf file options { listen-on port 53 {192.168.x.x;}; listen-on-v6 port 53 { ::1; }; directory "/var/named"; dump-file "/var/named/data/cache_dump.db"; statistics-file "/var/named/data/named_stats.txt"; memstatistics-file "/var/named/data/named_mem_stats.txt"; allow-query {any;}; recursion yes; 192.168.x.x is my local DNS address. then i copied lookups file in /var/named and edited the file "forward" $TTL 1D @ IN SOA abc.zoom.com. rahul.abc.zoom.com. ( 0 ; serial 1D ; refresh 1H ; retry 1W ; expire 3H ) ; minimum NS abc.zoom.com. abc A 192.168.x.x and for " reverse" $TTL 1D @ IN SOA abc.zoom.com. rahul.abc.zoom.com.( 0 ; serial 1D ; refresh 1H ; retry 1W ; expire 3H ) ; minimum NS abc.zoom.com. x PTR abc.zoom.com. when i put the public ip details in the Eth0 it was automatically redirect in to the resolve.conf when i checked through dig command the answer, query all were 1. my system is itself a Software router.In gateway of my all local machine i give my system ip address. however my DNS and Gateway IP is same. Now the problem is that. i gave the static ips to all my local machines when i give the DNS which i made i.e 192.168.x.x that time my ftp is not connect in filezilla software E.g: host : pqr.zoom.com ("zoom.com" is my local domain name) username : pqr password : pqr gives an error: Error: Connection timed out Error: Could not connect to server but if i give the public DNS address it get connected. i want to solve this problem please give solution on this.

    Read the article

< Previous Page | 52 53 54 55 56 57 58 59 60 61 62 63  | Next Page >