Search Results

Search found 17448 results on 698 pages for 'regular expressions info'.

Page 561/698 | < Previous Page | 557 558 559 560 561 562 563 564 565 566 567 568  | Next Page >

• Trying to retrieve data with a thermaltake blacX enclosure: Windows 7 believes the drive to be "uninitialized"

  - by Peeter Joot

  I have a laptop that won't boot. It appears to be a power problem ... laptop auto-turns-off within about 10 seconds of pressing the power button (with power buttons lighted temporarily and no display with or without external monitor). I've followed the dell troubleshooting guide which suggested reseating the memory modules and the hard drives, but that didn't help. Before trying to have the laptop serviced, I wanted to get some data off off the hard drive. I bought a thermaltake blacX enclosure, intending to use this to both use to retrieve the drive data with, and then later use as external storage. Following the instructions (insert cables, insert drive power on) goes fine, and Windows 7 on another laptop installs the device driver software. However, no drive letter shows up in 'Computer'. Under Computer-manage-storage I see the drive is there, and there's an option to "initialize" the drive. The Windows "initialize" dialog gives me the option to pick between "MBR" and "GPT" partitioning, which sounds like a good way to destroy the data on the drive. I'm thinking that I've purchased the wrong device for the job (or that my old drive is damaged). The old drive to recover info from is a Western Digital 500G/7200rpm SATA drive if that is relavent. Both the original laptop and the one I'm using for recovery are running Windows 7. Does anybody have experience with using a blacX enclosure to recover data off an already formatted drive?

  Read the article

• Issue with SSH on Ubuntu - Local connection ok, remote connection - Is it me or my ISP?

  - by Benjamin

  I have an issue with a server running Ubuntu 12.04, I am trying to set up a remote connection so I can access the server at my work from out of town. I have installed the SSH server and all that stuff, and I have reassigned the default port from 22 to 3399. A local connection from any OS can connect on the 192.168... address, but in no way can I get a connection on the actual IP address. I believe my configuration is correct, and I will attach it. If I have done something wrong in the config, please tell me and I will make a change to it. I honestly think that the Router that my ISP provided is horrible, and although the port for ssh is forwarded, it might be stopping any traffic coming inbound. Is there anything I can try to verify this? /var/log/auth does not show any error when I connect VIA our static IP. I have included all values not commented out below: (sshd_config) Port 3399 ListenAddress 0.0.0.0 Protocol 2 HostKey /etc/ssh/ssh_host_rsa_key HostKey /etc/ssh/ssh_host_dsa_key HostKey /etc/ssh/ssh_host_ecdsa_key UsePrivilegeSeparation yes KeyRegenerationInterval 3600 ServerKeyBits 768 SyslogFacility AUTH LogLevel INFO LoginGraceTime 120 PermitRootLogin yes StrictModes yes UseDNS no RSAAuthentication yes IgnoreRhosts yes RhostsRSAAuthentication no HostbasedAuthentication no PermitEmptyPasswords no ChallengeResponseAuthentication no PasswordAuthentication yes GSSAPIAuthentication no X11Forwarding yes X11DisplayOffset 10 PrintMotd no PrintLastLog yes TCPKeepAlive yes AcceptEnv LANG LC_* Subsystem sftp /usr/lib/openssh/sftp-server UsePAM yes Am I doing this wrong? port forwarding image

  Read the article

• LVS / IPVS difference in ActiveConn since upgrading

  - by Hans

  I've recently migrated from an old version of LVS / ldirectord (Ultra Monkey) to a new Debian install with ldirectord. Now the amount of Active Connections is usually higher than the amount of Inactive Connections, it used to be the other way around. Basically on the old load balancer the connections looked something like: -> RemoteAddress:Port Forward Weight ActiveConn InActConn -> 10.84.32.21:0 Masq 1 12 252 -> 10.84.32.22:0 Masq 1 18 368 However since migrating it to the new load balancer it looks more like: -> RemoteAddress:Port Forward Weight ActiveConn InActConn -> 10.84.32.21:0 Masq 1 313 141 -> 10.84.32.22:0 Masq 1 276 183 Old load balancer: Debian 3.1 ipvsadm 1.24 ldirectord 1.2.3 New load balancer: Debian 6.0.5 ipvsadm 1.25 ldirectord 1.0.3 (I guess the versioning system changed) Is it because the old load balancer was running a kernel from 2005, and ldirectord from 2004, and things have simply changed in the past 7 - 8 years? Did I miss some sysctl settings that I should be enforcing for it to behave in the same way? Everything appears to be working fine but can anyone see an issue with this behaviour? Thanks in advance! Additional info: I'm using LVS in masquerading mode, the real servers have the load balancer as their gateway. The real servers are running Apache, which hasn't changed during the upgrade. The boxes themselves show roughly the same amount of Inactive Connections shown in ipvsadm.

  Read the article

• linux shutdown hang with wifi cifs mounts

  - by Sirex

  Since fedora 15 (and now with 16) it seems that wireless clients take a long while to shutdown when they have network filesystems mounted at shutdown time. I've pushed out a cifs mount via puppet, and all clients have it, including those on wireless. If say a laptop is on a wired connection it shuts down just fine, but if its on the wifi at the time (and no wired connection) it'll hang at the fedora f logo. I'm not sure if its indefinite or just a really long while, but ill give it a test when i shut this machine down in a second. Needless to say its pretty annoying, so is there a way of causing the machine to shutdown even if network connectivity has been lost at unmount time, -- or an official way to reorder events so the wireless card is kept up until after the unmount happens during the shut down process (short of writing a custom script for shutdowns which is a bit of a kludge) ? It does this on multiple machines, and all started doing it when we went from fedora 14 to 15. It was such an obvious issue i'd kind of assumed someone must have reported it or there was an easy fix, but i've not discovered anything yet. Additional info: I can confirm that manually unmounting the mounts then shutting down (sudo shutdown or the xfce shutdown button) will shutdown just fine, it only hangs if the mounts are still mounted The puppet config that sets the mount looks like this (now with the _netdev entry that is indeed pushed to clients successfully, but makes no difference): file { "/mnt/share": ensure = directory,} mount { "/mnt/share": atboot = true, ensure = mounted, remounts = false, fstype = cifs, device = "//srv/share", options = "user,gid=shareusers,uid=${user},file_mode=0700,dir_mode=0700,credentials=/root/.smbcreds,_netdev", require = [ File["/mnt/share"], Group["shareusers"] ], } }

  Read the article

• Can a website see/know my MAC address even if I use a VPN?

  - by ilhan

  I have searched other results and read many of them but I could not get an enough information. My question is that can a website see my MAC address or can they have an information about that I'm the same person under these conditions: I am using a VPN and I use two IPs: first one is normal one, the second one is the VPN's IP. I use two browsers to hide behind browser fingerprinting. I use both browsers with Incognito Mode. I always use one for normal IP, one for the VPN IP. I do not know that if the website uses cookies or not. But can they collect an enough information to prove that these two identities belong to same person? Is there any other way for them to see that I am the same person? I use different IPs, different browsers and I use both browsers in incognito mode. I even changed one of browsers language to only English. So even if they collect my info from browser, they will see two browsers using different languages. (Addition after edit): So I have changed my IP and browser information and the website can not reach this information anymore to prove that I am the same person using two accounts. Then let's come to the title: Can they see my MAC address? Because I think that it is the last way that they can identify me and my main question is that. I wrote the information above to mention that I changed IPs and I have some precautions to avoid browser fingerprinting (btw my VPN provider already has a service about blocking it). I wrote them because I read similar advices in some related questions but my question is that can they see my MAC address (or anything else that can make me detected) despite all these precautions. And lastly, Is there an extra way to be anonymized that I can do? For example, can my system clock or anything else give an information? Thanks in advance.

  Read the article

• Monitor attached to motherboard is out of frequency

  - by Neilvert Noval

  I don't know if this is appropriate to ask it here in superuser. Please, just route this to appropriate stackexchange site if found unrelevant. Here's my scenario. I have bought a new motherboard (MSI 785GT-E63). I already have an old CRT monitor connected to it. After I install a linux OS to it, my monitor will display that it is: Out of frequency. Current frequency is 89Hz. The operating output of my monitor is (around) 60-70Hz. I would like to get this thing work. How can I let my CRT display properly? I was thinking of lowering down video frequency output of my motherboard, but I can't find any settings on my BIOS setup. Additional info: My monitor is attached directly to the built-in video adaptor of my motherboard. (No additional video cards) Install of OS is complete without errors. Please help.

  Read the article

• Cannot access new folders created in my Apache2 document-root

  - by user235101

  I have tried to create a new folder 'test' in my documentroot of my Apache2 installation, however, whenever I try and access it from a web-browser it gives me a 403 (forbidden) error. My virtualhosts file - <VirtualHost *:80> ServerAdmin webmaster@localhost ServerName REMOVED DocumentRoot /var/www/ <Directory /> Options FollowSymLinks AllowOverride All AuthType Digest AuthName "documentroot" AuthDigestProvider file AuthUserFile /etc/apache2/htpasswd Require user REMOVED AllowOverride Indexes </Directory> <Directory /var/www/> Options FollowSymLinks Options -Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> <Directory /var/www/share/> Order Deny,Allow Allow from all Satisfy any </Directory> <Directory /var/www/REMOVED/> Order Deny,Allow Allow from all Satisfy any </Directory> <Directory /var/www/stream/> Order Deny,Allow Allow from all Satisfy any </Directory> <Directory /var/www/test> Order Deny,Allow Allow from all Satisfy any </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined <Directory /var/www/REMOVED> AuthType Digest AuthName "rutorrent" AuthDigestDomain /var/www/REMOVED/ http://46.105.127.19/REMOVED AuthDigestProvider file AuthUserFile /etc/apache2/htpasswd Require valid-user SetEnv R_ENV "/var/www/REMOVED" AllowOverride Indexes </Directory> </VirtualHost> Image of the permissions - Other information - If I create a new folder (and use chmod --reference to ensure it has the same permissions as an accessible folder), I get a 403 client-side. If I copy folder 'rapidleech' to the name 'rapidleech1', it will let access 'rapidleech1', but no longer 'rapidleech', until I delete the copy. In my logs I found nothing logged in errors.log, and only that it delivered a 403 in access.log. All the appropriate users are members of www-data.

  Read the article

• Website hosted on my virtualbox web server not displaying images or applying css when viewed through phone

  - by WebweaverD

  I would really appreciate it if someone could help me. Please let me know if you need more info in the comments. My Set Up I have a windows 7 pc. On it I run a virtual box VM with a ubuntu 12 guest os and LAMP setup. I share files between the two machines using samba from linux to windows and using windows file sharing (Workgroup) the other way round. The vm is set up with a bridged network adapter and can happily serve web pages to my host machine. I use DHCP reservations on my home wireless router/modem to reserve an ip for the vm and give it a sitename.dev in my windows host file so I can access it at sitename.dev through the browser. The Problem So far so good but I have a dev project which needs a lot of mobile template development, now obviously I can use a browser plugin to simulate a mobile device but I would like to be able to see the real thing easily on my phone during development. So ideally I would like a similar setup on my iphone to my windows setup Now I'm not great on networking and dont have much experience with web server set up. So when I typed the ip of my virtual box into my iphone i wasnt expecting to see anything. I was pleasantly surprised when my site loaded up. The javascript even seems to be running but the images and css are not happening. My Question 1) What is happening here, is it something to do with the bridged set up on the vm network? 2)How do I make the sites load properly through my phone Notes I've also tried another phone. The same sites viewed on live servers work fine.

  Read the article

• Firefox url / link to a group of saved bookmarks?

  - by This_Is_Fun

  In Firefox you can easily save a group of tabs together. When (re-)accessing this group, the 'cascading' bookmark menu shows each individual bookmark (and under a line) it says "open all in tabs" I'm looking for a way to launch those tabs without going up through the bookmark menu. Possible options: A) Record a simple macro w/ any number of "superuser" utilities* ('A' is not the preferred option, since many 'little-macros' are hard to keep track of) b) Use Autohotkey (similar to option 'A' and more flexible once you learn the basics) c) How does Firefox load all those tabs? The info must be stored somewhere (as a type of URL??) Quick Summary: The moment I click on "open all in tabs", I am clicking on something very similar to a hyper-link. How do I find the content (exact code) of that 'hyper-link', and / or "How do I easily launch the tabs?" .. . New EDIT #1: I'm looking for a way to launch those tabs without going up through the bookmark menu, or cluttering the bookmarks toolbar which I hide anyway :o) .. . New EDIT #2: I tried to keep the question simple and not mentioning Autohotkey programming. The objective is to launch all tabs using a button on an AHK gui. When grawity said, "It's just an ordinary folder containing ordinary bookmarks," he (she) reminds me I can easily find the folder / Now how to launch to urls inside that folder? .. FYI: (Basic-level) AHK works like this: ; Open one folder ButtonWinMerge_Files: Run, C:\Program Files\WinMerge\ Return .. ; Use default web browser for one link ButtonGoogle: Run, http://google.com Return .. . Question still open: The moment I click on "open all in tabs", I am clicking on something very similar to a hyper-link. "How to 'replicate' the way Firefox launches the tabs with one click?"

  Read the article

• centos install / partitioning

  - by ServerSideX

  I'm using NOC-PS to remotely install Centos 6.2 via KVM / IPMI. I'm going to install cPanel as well and they recommend this layout /boot (99MB) swap (2x server RAM) / (remainder) In the o/s install profile within NOC-PS software, it shows as this: part /boot --fstype ext2 --size 250 part pv.01 --size 1 --grow volgroup vg pv.01 logvol / --vgname=vg --size=1 --grow --fstype ext4 --fsoptions=discard,noatime --name=root logvol /tmp --vgname=vg --size=1024 --fstype ext4 --fsoptions=discard,noatime --name=tmp logvol swap --vgname=vg --recommended --name=swap By the time the default partition setup was done installing Centos, I get this [root@server005 ~]# df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/vg-root 532G 907M 504G 1% / tmpfs 7.8G 0 7.8G 0% /dev/shm /dev/sda1 243M 28M 202M 13% /boot /dev/mapper/vg-tmp 1008M 34M 924M 4% /tmp [root@server005 ~]# cat /etc/fstab # # /etc/fstab # Created by anaconda on Fri Dec 7 18:47:24 2012 # # Accessible filesystems, by reference, are maintained under '/dev/disk' # See man pages fstab(5), findfs(8), mount(8) and/or blkid(8) for more info # /dev/mapper/vg-root / ext4 discard,noatime 1 1 UUID=58b31aaf-5072-4fb1-a858-33bc316fa793 /boot ext2 defaults 1 2 /dev/mapper/vg-tmp /tmp ext4 discard,noatime 1 2 /dev/mapper/vg-swap swap swap defaults 0 0 tmpfs /dev/shm tmpfs defaults 0 0 devpts /dev/pts devpts gid=5,mode=620 0 0 sysfs /sys sysfs defaults 0 0 proc /proc proc defaults 0 0 My question is, how should the NOC-PS install profile look like to get the recommended cPanel partitioning? The server has 16GB RAM, dual 600GB SAS drives and will be used for cPanel shared hosting.

  Read the article

• Netbook thinks it is a desktop

  - by Narcolapser

  Question: Are, and if so what, there packages for download that I can get netbook to understand it is not a desktop and that it is a netbook. Info: I'm running an Acer Aspire One with ubuntu desktop 9.10. I tried Ubuntu Netbook Remix first but it has graphics issues with the aspire one. So I changed to Ubuntu Desktop. It was the only distro (after debian, centOS, Fedora, and Knoppix all failed me) that I managed to get working. The only thing is that it is having issues doing things that a netbook/laptop should be doing. most notably is that it will run it's battery dead if I close the screen and throw it into my back pack. It seems to just stay fully on and runs it's self to death. also it will lock up some times if I close the screen and come back to it 10 or 20 minutes later. It also won't retain volume settings when I reboot, as well as screen brightness. and just a couple of other things that I can't quite put my finger on, but just seem amiss. like I said, Essentially my netbook thinks it is a desktop, how can I fix this? ~N

  Read the article

• Windows 7 BSOD on boot after windows update

  - by Razor Storm

  After Windows updates today, I restarted my desktop (for the first time in a couple weeks), and on boot up ran into a BSOD: STOP: 0x0000007E (0xFFFFFFFFC0000005, 0xFFFFF8000355AB5A, 0xFFFFF880031CB3A8, 0xFFFFF880031CAC10) I tried system restore, but there was only 1 restore point which was from all the way back in January. I tried it anyway but after 10 minutes of running it said system restore could not be completed. Additional info: I checked my BIOS and it is detecting my rams. CPU is Intel Sandy Bridge i5-2500k overclocked to 4.3GHz. I reclocked it back to stock speeds (3.3 GHz) in case it was causing the issue (I highly doubt that it is). But the problem persists. Running Windows 7. 12 GB of RAM at 1333 MHz OS on 64gb SSD. What is causing this? How should I fix it? Also, if it is caused by windows update, is there a way to undo the update with command prompt? I tried safemode, and the blue screen comes up as well, but I am able to access command prompt.

  Read the article

• Cannot get at data in my NAS

  - by Ben

  I've got a bit of an issue that I'm hoping you can help me with. I have an Iomega ix4 as my NAS. This runs Linux and each drive in the box has 2 partitions: one for the OS and RAID info, and the second for the actual data. I had it configured as RAID5. Recently one of the drives failed. At this point all of the data was available, it was just reporting a failed drive. I had a drive of the same capacity (although not the exact same spec) which I swapped in place of the failed drive. It recognised it, and started to rebuild the data protection. So far so good ... or so I thought. The next day, after data protection had finished reconstructing, the NAS was telling me that 4 new drives had been added, and wanted confirmation to overwrite the data. Obviously I declined to do this. I swapped the failed drive back in again, in the hope that it would return to its previous state of the data being accessible, but one failed disk. However it didn't - it still tells me that the NAS has 4 new drives in it. I am hopeful that the actual data is untouched, so what I need to do is get it to rebuild the RAID without touching the data on the disks. I have ssh access, and have run stuff like mdadm --examine to see what I can find. The mdadm.conf file has no entry in the "definitions of existing MD arrays" section. I have not run any actual rebuilding commands as yet, because this is entering an area which I am out of my depth in. Please can someone advise the best way of getting my data? Thanks.

  Read the article

• Google Chrome won't install via IE9/Windows7

  - by purir

  Using IE9, I've tried installing Google Chrome on Windows 7 from this url http://www.google.com/chrome/eula.html?hl=en-GB&platform=win But get the following error (apologies for uncouthly dumping this nonsense...) Any ideas dearly appreciated! PLATFORM VERSION INFO Windows : 6.1.7601.65536 (Win32NT) Common Language Runtime : 4.0.30319.235 System.Deployment.dll : 4.0.30319.1 (RTMRel.030319-0100) clr.dll : 4.0.30319.235 (RTMGDR.030319-2300) dfdll.dll : 4.0.30319.1 (RTMRel.030319-0100) dfshim.dll : 4.0.31106.0 (Main.031106-0000) SOURCES Deployment url : _http://dl.google.com/update2/1.3.21.57/GoogleInstaller_en-GB.application?appguid%3D%7B8A69D345-D564-463C-AFF1-A69D9E530F96%7D%26iid%3D%7B26C55C3A-B26A-0484-FEDD-78443D269DA1%7D%26lang%3Den-GB%26browser%3D2%26usagestats%3D0%26appname%3DGoogle%2520Chrome%26needsadmin%3Dfalse%26installdataindex%3Ddefaultbrowser ERROR SUMMARY Below is a summary of the errors, details of these errors are listed later in the log. * Activation of _http://dl.google.com/update2/1.3.21.57/GoogleInstaller_en-GB.application?appguid%3D%7B8A69D345-D564-463C-AFF1-A69D9E530F96%7D%26iid%3D%7B26C55C3A-B26A-0484-FEDD-78443D269DA1%7D%26lang%3Den-GB%26browser%3D2%26usagestats%3D0%26appname%3DGoogle%2520Chrome%26needsadmin%3Dfalse%26installdataindex%3Ddefaultbrowser resulted in exception. Following failure messages were detected: + The system cannot find the file specified. (Exception from HRESULT: 0x80070002) COMPONENT STORE TRANSACTION FAILURE SUMMARY No transaction error was detected. WARNINGS There were no warnings during this operation. OPERATION PROGRESS STATUS * [25/06/2011 11:41:04] : Activation of _http://dl.google.com/update2/1.3.21.57/GoogleInstaller_en-GB.application?appguid%3D%7B8A69D345-D564-463C-AFF1-A69D9E530F96%7D%26iid%3D%7B26C55C3A-B26A-0484-FEDD-78443D269DA1%7D%26lang%3Den-GB%26browser%3D2%26usagestats%3D0%26appname%3DGoogle%2520Chrome%26needsadmin%3Dfalse%26installdataindex%3Ddefaultbrowser has started. ERROR DETAILS Following errors were detected during this operation. * [25/06/2011 11:41:04] System.IO.FileNotFoundException - The system cannot find the file specified. (Exception from HRESULT: 0x80070002) - Source: System.Deployment - Stack trace: at System.Deployment.Internal.Isolation.IsolationInterop.GetUserStore(UInt32 Flags, IntPtr hToken, Guid& riid) at System.Deployment.Application.ComponentStore..ctor(ComponentStoreType storeType, SubscriptionStore subStore) at System.Deployment.Application.SubscriptionStore..ctor(String deployPath, String tempPath, ComponentStoreType storeType) at System.Deployment.Application.SubscriptionStore.get_CurrentUser() at System.Deployment.Application.ApplicationActivator.PerformDeploymentActivation(Uri activationUri, Boolean isShortcut, String textualSubId, String deploymentProviderUrlFromExtension, BrowserSettings browserSettings, String& errorPageUrl) at System.Deployment.Application.ApplicationActivator.ActivateDeploymentWorker(Object state) COMPONENT STORE TRANSACTION DETAILS No transaction information is available.

  Read the article

• suPHP not working

  - by amarc

  OS: Ubuntu 10.04 etc/suphp/suphp.conf: [global] ;Path to logfile logfile=/var/log/suphp/suphp.log ;Loglevel loglevel=info ;User Apache is running as webserver_user=www-data ;Path all scripts have to be in docroot=/home ;Path to chroot() to before executing script ;chroot=/mychroot ; Security options allow_file_group_writeable=false allow_file_others_writeable=false allow_directory_group_writeable=false allow_directory_others_writeable=false ;Check wheter script is within DOCUMENT_ROOT check_vhost_docroot=true ;Send minor error messages to browser errors_to_browser=false ;PATH environment variable env_path=/bin:/usr/bin ;Umask to set, specify in octal notation umask=0077 ; Minimum UID min_uid=100 ; Minimum GID min_gid=100 [handlers] ;Handler for php-scripts application/x-httpd-suphp="php:/usr/bin/php-cgi" ;Handler for CGI-scripts x-suphp-cgi="execute:!self" some vhost in sites-enabled: NameVirtualHost *:8080 <VirtualHost *:8080> ServerAdmin ... ServerName ... ServerAlias ... AddType application/x-httpd-php .php AddHandler application/x-httpd-php .php suPHP_Engine on suPHP_UserGroup user user suPHP_ConfigPath "/home/user/etc" suPHP_PHPPath /usr/bin DocumentRoot /home/user/web/site.com/ ErrorLog /var/log/apache2/site.com-error_log CustomLog /var/log/apache2/site.com-access_log common <Directory /home/user/web/site.com/> Order Deny,Allow Allow from all Options +Indexes </Directory> </VirtualHost> But when I did nano /home/user/web/id.php and paste <?php system('id'); ?> in it, result I get is: uid=33(www-data) gid=33(www-data) groups=33(www-data) Have no idea what to do so I was hoping comunity could help ty.

  Read the article

• Must have local user to authenticate Samba to AD?

  - by Phil

  I've got a CentOS 5.3 server with Samba running. I've joined this server to my domain in the hopes of allowing AD users some access to my Samba shares. I've found that this works, but only as long as the AD username that I'm trying to authenticate with is also a local user on the server. In other words, if I'm trying to access a share, and try to authenticate with the AD username "joe", I get errors unless I create a user named 'joe' on the server. I don't have to create a matching password or anything....the local user's password is always blank, so I do know that the authentication is actually happening against the AD. Here's my smb.conf file: [global] workgroup = <mydomain> server string = <snip> netbios name = HOME security = ADS realm = <mydomain.com> password server = <snip> auth methods = winbind log level = 1 log file = /var/log/samba/%m.log [amore] path = /var/www/amore browseable = yes writable = yes valid users = DOMAIN\user1 DOMAIN\user2 DOMAIN\user3 DOMAIN\user4 I would assume that my kerberos settings are fine, as I've joined the domain and can use wbinfo to see users and groups. However, I can provide that info if necessary. Anyone have any ideas?

  Read the article

• Backtrack, Wi-Fi not working

  - by hradecek

  I've installed Backtrack 5R3 KDE, and I realized that my wireless is not working, but wired is working fine. Here's the lshw output: *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 05 serial: 04:7d:7b:b7:46:f8 size: 100MB/s capacity: 100MB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw ip=192.168.2.2 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:42 ioport:2000(size=256) memory:f0404000-f0404fff memory:f0400000-f0403fff lspci output: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:14.0 USB Controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB Controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.1 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 2 (rev c4) 00:1d.0 USB Controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05)

  Read the article

• Windows Server 2008 IIS7 - page requests randomly hang or timeout

  - by seb835

  I've just installed a fresh copy of Windows Server 2008 x64 with IIS7 and PHP (fast CGI). However, I'm noticing that after moving my web site from a similarly specified machine to this one, I'm getting issues. The issue seems to be that randomly, as I'm clicking through the web pages being served, the browser will suddenly hang saying "waiting for mysite.com...". Sometimes the page will then timeout, or finally resolve after 20 to 30 seconds, but maybe missing the CSS style sheet. Very strange, as this is the only website installed on this new server, and only myself using/testing it. Server is installed in the same data centre below the old server. Has anyone else had a similar problem? I tried increasing the max workers pool to 10 (from 1), but this has no effect. Seems to happen most frequently after 1 or 2 minutes of inactivity on the website, then trying to load/refresh a web page. Many thank for any info and help. Kind Regards, Seb

  Read the article

• Never getting a JSON response when running server-side PHP proxy script but I do with others

  - by Dohk

  I'm on PHP 5.3.4 and Apache 2.2 btw So I'm using (or trying to use) Simple PHP Proxy (Simple PHP Proxy) I enter a URL at his example page at SPP Example Page and it works fine, I see the JSON response and all the headers. However, when I copy the exact URL, only changing the URL to now have localhost, I get both empty headers and no JSON. Assuming that the script on his site is the same I downloaded, could this be due to a multitude of things or a setting in Apache and/or the PHP ini? So for example: benalman.com/code/projects/php-simple-proxy/ba-simple-proxy.php?url=http://github.com/&full_headers=1&full_status=1 That will get me a ton of info back Now changing to localhost http://localhost/ba-simple-proxy.php?url=http://github.com/&full_headers=1&full_status=1 {"headers":[],"status":{"url":"https:\/\/github.com\/","content_type":"text\/html","http_code":301,"header_size":194,"request_size":182,"filetime":-1,"ssl_verify_result":0,"redirect_count":1,"total_time":0.094,"namelookup_time":0,"connect_time":0.047,"pretransfer_time":0,"size_upload":0,"size_download":185,"speed_download":1968,"speed_upload":0,"download_content_length":185,"upload_content_length":0,"starttransfer_time":0,"redirect_time":0.047,"certinfo":[]},"contents":null} I even went basic and just used some curl and of course, empty objects being returned other than false for my content and the url I set in my JSON. Any help is deeply appreciated or any ideas.

  Read the article

• Why is my computer randomly restarting? How can I fix it?

  - by kinglime

  I have a custom built desktop computer that I've been using since about a year ago. The main specs are: ASUS P8Z68-V LE Motherboard Intel Core i7 2600k Corsair Vengeance 16GB Ram ASUS ENGTX570 GPU Corsair TX650M PSU I was running an overclock of 4.4ghz for my cpu (I have a Hyper212 EVO) and 1600mhz for my RAM but have it currently turned off due to my issues. I am also currently running Windows 8 but this problem occured in Windows 7 too. Basically my issue is that seemingly randomly, with no pattern my PC will reset itself and ASUS Anti-Surge will alert me that something went wrong. This issue is not related to system stress. I can run it fine for an hour maxxed out on Prime95 then later I can be watching a mere YouTube video when it will randomly reset. This has been occurring probably for the last two weeks and it seems to be getting worse. I believe this might be related to the power supply but when I monitor it in the bios and in Windows it appears to be putting out the proper voltages. Also possibly related or not but my Nvidia drivers frequently temporarily fail and then warn me of some kind of kernel error? If I have to buy a new power supply that is what I'll do but I want to make damn sure that's the only issue at hand. Thank you everyone in advance, please help me diagnose the issue and tell me what I can do to fix it. If you need any additional info about my setup please ask me.

  Read the article

• Securing phpmyadmin: non-standard port + https

  - by elect

  Trying to secure phpmyadmin, we already did the following: Cookie Auth login firewall off tcp port 3306. running on non-standard port Now we would like to implement https... but how could it work with phpmyadmin running already on a non-stardard port? This is the apache config: # PHP MY ADMIN <VirtualHost *:$CUSTOMPORT> Alias /phpmyadmin /usr/share/phpmyadmin <Directory /usr/share/phpmyadmin> Options FollowSymLinks DirectoryIndex index.php <IfModule mod_php5.c> AddType application/x-httpd-php .php php_flag magic_quotes_gpc Off php_flag track_vars On php_flag register_globals Off php_value include_path . </IfModule> </Directory> # Disallow web access to directories that don't need it <Directory /usr/share/phpmyadmin/libraries> Order Deny,Allow Deny from All </Directory> <Directory /usr/share/phpmyadmin/setup/lib> Order Deny,Allow Deny from All </Directory> # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog ${APACHE_LOG_DIR}/phpmyadmin.log combined </VirtualHost>

  Read the article

• How do I setup a proper VPN for my friends to play LAN games AND give them internet access?

  - by Gizmo

  I'm trying to setup a VPN on my local network, but everyone who connects to me DOES have access to my laptop but not to the internet or other devices on the network. How can I properly configure my VPN on windows to work correctly (giving internet + access to all devices on my network to the remote pc)? Or is there software on windows which makes creating a VPN server easier? or maybe a VMWare image linux vpn server? I can't find any of those! My requirement is that my friends don't have to install additional software, they have to be able to connect with default windows stuff. My OS is Windows 8 Standart edition (not pro or enterprise) OEM. Most of my friends have also windows 8, some windows 7. Extra info: My device is DMZ'ed (Demilitarized Zone, [disabled NAT on my device so it's accessible on the WAN]) I can access files, websites and services on other devices on my network, and all devices can access file shares, website and all other services on my device When enabling VPN everything works except the client is unable to get internet access or access to any device on my network, client has only access to my device.

  Read the article

• Is it possible to create a simple frontend indexer for openbittorent torrents?

  - by SimonK

  I run a website which distributes a few files every now and again, live music performances by a rock band. I create a torrent file, set the trackers as openbittorrent, publicbt and other similar open trackers. I upload the torrent file to my forum, my users download it and the files are shared. No problems there. What I would like to do is index those torrents properly on my website though so I can follow seeders/leechers and other stats online. I know the open torrent trackers don't have an index but I am aware of many, many indexing sites that do that exact thing. I don't know how though. So what I'm asking is what do I need to do to do that myself? I simply want to create a page that lists the torrents I and other users on my site create, the seeders/leechers ratio and a link to the torrent file etc. What data do I need to be able to do that? I'm proficient in general web design but I don't know what I would need data wise to pull the required info on the torrents? Thanks

  Read the article

• Ping not working

  - by Nishant

  Ping is not working to and from this IP to my computer. inet addr:10.125.104.4 Bcast:10.125.111.255 Mask:255.255.240.0 My computer is like this Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 10.125.65.75 Subnet Mask . . . . . . . . . . . : 255.255.252.0 Default Gateway . . . . . . . . . : 10.125.64.6 We both CAN reach the common gateway IP , 10.125.96.6 . What should I check ? What is the barrier in sending info if we both have a common gateway that is pingable ? Besides I can login to a intermediate server and ssh to this server also !!

  Read the article

• Rails application keeps timing out when attempting to connect to Postgresql DB

  - by Corillian

  I'm hosting a postgresql database on a small windows azure Ubuntu 13.04 VM with a default postgresql.conf. I have a Rails application running on a medium windows azure Ubuntu 13.04 VM. When accessing the postgresql database the rails application is constantly timing out. In its database.yml I have the connection pool size set to 120 and the timeout set to 15 seconds. Despite this my rails logs are full of the following error message: ActiveRecord::ConnectionTimeoutError: could not obtain a database connection within 5 seconds (waited 5.0023203 seconds). The max pool size is currently 120; consider increasing it. My postgresql.conf has a max connection limit of 120, making it any larger prevents the server from being able to successfully restart. I've also made sure that ssl was off in the postgresql.conf per this article but beyond that I have no idea what's going on. My postgresql logs don't contain any info indicating something is going wrong. My website is getting ~1k hits per day so perhaps a small VM instance just isn't powerful enough? I appreciate any assistance! [Edit1] The postgresql database is in a separate cloud service within the same affinity group. For example: db small VM: mydatabase.cloudapp.net (Affinity Group US East) forums medium VM: myforums.cloudapp.net (Affinity Group US East) On the database server I have opened port 5432. The connection to the database server from the forums server is using its hostname. Is it possible that the DNS resolution is what's taking so long?

  Read the article

< Previous Page | 557 558 559 560 561 562 563 564 565 566 567 568  | Next Page >