Search Results

Search found 15132 results on 606 pages for 'svn tools'.

Page 561/606 | < Previous Page | 557 558 559 560 561 562 563 564 565 566 567 568  | Next Page >

• Recover harddrive data

  - by gameshints

  I have a dell laptop that recently "died" (It would get the blue screen of death upon starting) and the hard drive would make a weird cyclic clicking noises. I wanted to see if I could use some tools on my linux machine to recover the data, so I plugged it into there. If I run "fdisk" I get: Disk /dev/sdb: 20.0 GB, 20003880960 bytes 64 heads, 32 sectors/track, 19077 cylinders Units = cylinders of 2048 * 512 = 1048576 bytes Disk identifier: 0x64651a0a Disk /dev/sdb doesn't contain a valid partition table Fine, the partition table is messed up. However if I run "testdisk" in attempt to fix the table, it freezes at this point, making the same cyclical clicking noises: Disk /dev/sdb - 20 GB / 18 GiB - CHS 19078 64 32 Analyse cylinder 158/19077: 00% I don't really care about the hard drive working again, and just the data, so I ran "gpart" to figure out where the partitions used to be. I got this: dev(/dev/sdb) mss(512) chs(19077/64/32)(LBA) #s(39069696) size(19077mb) * Warning: strange partition table magic 0x2A55. Primary partition(1) type: 222(0xDE)(UNKNOWN) size: 15mb #s(31429) s(63-31491) chs: (0/1/1)-(3/126/63)d (0/1/32)-(15/24/4)r hex: 00 01 01 00 DE 7E 3F 03 3F 00 00 00 C5 7A 00 00 Primary partition(2) type: 007(0x07)(OS/2 HPFS, NTFS, QNX or Advanced UNIX) (BOOT) size: 19021mb #s(38956987) s(31492-38988478) chs: (4/0/1)-(895/126/63)d (15/24/5)-(19037/21/31)r hex: 80 00 01 04 07 7E FF 7F 04 7B 00 00 BB 6F 52 02 So I tried to mount just to the old NTFS partition, but got an error: sudo mount -o loop,ro,offset=16123904 -t ntfs /dev/sdb /mnt/usb NTFS signature is missing. Ugh. Okay. But then I tried to get a raw data dump by running dd if=/dev/sdb of=/home/erik/brokenhd skip=31492 count=38956987 But the file got up to 59885568 bytes, and made the same cyclical clicking noises. Obviously there is a bad sector, but I don't know what to do about it! The data is still there... if I view that 57MB file in textpad... I can see raw data from files. How can I get my data back? Thanks for any suggestions, Solution: I was able to recover about 90% of my data: Froze harddrive in freezer Used Ddrescue to make a copy of the drive Since Ddrescue wasn't able to get enough of my drive to use testdisk to recover my partitions/file system, I ended up using photorec to recover most of my files

  Read the article

• AWS EC2 - How to specify an IAM role for an instance being launched via awscli

  - by Skaperen

  I am using the "aws ec2 run-instances" command (from the awscli package) to launch an instance in AWS EC2. I want to set an IAM role on the instance I am launching. The IAM role is configured and I can use it successfully when launching an instance from the AWS web UI. But when I try to do this using that command, and the "--iam-instance-profile" option, it failed. Doing "aws ec2 run-instances help" shows Arn= and Name= subfields for the value. When I try to look up the Arn using "aws iam list-instance-profiles" it gives this error message: A client error (AccessDenied) occurred: User: arn:aws:sts::xxxxxxxxxxxx:assumed-role/shell/i-15c2766d is not authorized to perform: iam:ListInstanceProfiles on resource: arn:aws:iam::xxxxxxxxxxxx:instance-profile/ (where xxxxxxxxxxxx is my AWS 12-digit account number) I looked up the Arn string via the web UI and used that via "--iam-instance-profile Arn=arn:aws:iam::xxxxxxxxxxxx:instance-profile/shell" on the run-instances command, and that failed with: A client error (UnauthorizedOperation) occurred: You are not authorized to perform this operation. If I leave off the "--iam-instance-profile" option entirely, the instance will launch but it will not have the IAM role setting I need. So the permission seems to have something to do with using "--iam-instance-profile" or accessing IAM data. I repeated several times in case of AWS glitches (they happen sometimes) and no success. I suspected that perhaps there is a restriction that an instance with an IAM role is not allowed to launch an instance with a more powerful IAM role. But in this case, the instance I am doing the command in has the same IAM role that I am trying to use. named "shell" (though I also tried using another one, no luck). Is setting an IAM role not even permitted from an instance (via its IAM role credentials)? Is there some higher IAM role permission needed to use IAM roles, than is needed for just launching a plain instance? Is "--iam-instance-profile" the appropriate way to specify an IAM role? Do I need to use a subset of the Arn string, or format it in some other way? Is it possible to set up an IAM role that can do any IAM role accesses (maybe a "Super Root IAM" ... making up this name)? FYI, everything involves Linux running on the instances. Also, I am running all this from an instance because I could not get these tools installed on my desktop. That and I do not want to put my IAM user credentials on any AWS storage as advised by AWS here. after answered: I did not mention the launching instance permission of "PowerUserAccess" (vs. "AdministratorAccess") because I did not realize additional access was needed at the time the question was asked. I assumed that the IAM role was "information" attached to the launch. But it really is more than that. It is a granting of permission.

  Read the article

• FFMPEG Segfault Solutions

  - by Brentley_11

  I'm trying to convert a bunch of movies into h.264 mp4's using FFMPEG. These movies are sourced from various portable camcorders such as the Flip Mino HD and the Kodak ZI8. One issue I'm having with video from the ZI8 is it seems to be causing FFMPEG to segfault. Here is my command: ffmpeg -i 'XmasSailor720p60fps.MOV' -threads 2 -acodec libfaac -ab 96kb -vcodec libx264 -vpre hq -b 500kb -s 484x272 XmasSailor.mp4 Here is the output: FFmpeg version SVN-r20668, Copyright (c) 2000-2009 Fabrice Bellard, et al. built on Dec 2 2009 18:37:34 with gcc 4.2.4 (Ubuntu 4.2.4-1ubuntu4) configuration: --enable-libfaac --enable-libfaad --enable-libmp3lame --enable-libx264 --enable-gpl --enable-nonfree --enable-postproc --enable-pthreads --enable-shared libavutil 50. 5. 1 / 50. 5. 1 libavcodec 52.42. 0 / 52.42. 0 libavformat 52.39. 2 / 52.39. 2 libavdevice 52. 2. 0 / 52. 2. 0 libswscale 0. 7. 2 / 0. 7. 2 libpostproc 51. 2. 0 / 51. 2. 0 Seems stream 0 codec frame rate differs from container frame rate: 59.94 (60000/1001) -> 29.97 (30000/1001) Input #0, mov,mp4,m4a,3gp,3g2,mj2, from 'XmasSailor720p60fps.MOV': Duration: 00:00:05.37, start: 0.000000, bitrate: 12021 kb/s Stream #0.0(eng): Video: h264, yuv420p, 1280x720 [PAR 1:1 DAR 16:9], 11994 kb/s, 29.97 tbr, 90k tbn, 59.94 tbc Stream #0.1(eng): Audio: aac, 48000 Hz, stereo, s16, 128 kb/s Metadata major_brand : qt minor_version : 0 compatible_brands: qt comment : KODAK Zi8 Pocket Video Camera comment-eng : KODAK Zi8 Pocket Video Camera [libx264 @ 0x99e1020]using SAR=1/1 [libx264 @ 0x99e1020]using cpu capabilities: MMX2 SSE2Fast SSSE3 FastShuffle SSE4.1 Cache64 [libx264 @ 0x99e1020]profile High, level 2.1 Output #0, mp4, to 'XmasSailor.mp4': Stream #0.0(eng): Video: libx264, yuv420p, 484x272 [PAR 1:1 DAR 121:68], q=10-51, 500 kb/s, 30k tbn, 29.97 tbc Stream #0.1(eng): Audio: aac, 48000 Hz, stereo, s16, 96 kb/s Metadata comment : Encoded with the Statusfirm Video Transcoder Stream mapping: Stream #0.0 -> #0.0 Stream #0.1 -> #0.1 Press [q] to stop encoding [h264 @ 0x99de950]B picture before any references, skipping [h264 @ 0x99de950]decode_slice_header error [h264 @ 0x99de950]no frame! Error while decoding stream #0.0 [h264 @ 0x99de950]B picture before any references, skipping [h264 @ 0x99de950]decode_slice_header error [h264 @ 0x99de950]no frame! Error while decoding stream #0.0 frame= 20 fps= 0 q=13797729.0 size= 0kB time=0.66 bitrate= 0.6kbits/s frame= 39 fps= 37 q=13797729.0 size= 0kB time=1.30 bitrate= 0.3kbits/s frame= 48 fps= 30 q=33.0 size= 11kB time=0.10 bitrate= 903.0kbits/s frame= 58 fps= 27 q=31.0 size= 22kB time=0.43 bitrate= 421.0kbits/s frame= 67 fps= 25 q=29.0 size= 41kB time=0.73 bitrate= 462.6kbits/s frame= 75 fps= 23 q=29.0 size= 59kB time=1.00 bitrate= 486.7kbits/s frame= 83 fps= 22 q=29.0 size= 81kB time=1.27 bitrate= 521.9kbits/s frame= 90 fps= 21 q=29.0 size= 97kB time=1.50 bitrate= 530.1kbits/s frame= 98 fps= 20 q=29.0 size= 114kB time=1.77 bitrate= 526.9kbits/s frame= 106 fps= 20 q=29.0 size= 134kB time=2.04 bitrate= 537.7kbits/s frame= 114 fps= 19 q=29.0 size= 150kB time=2.30 bitrate= 533.7kbits/s frame= 122 fps= 19 q=29.0 size= 172kB time=2.57 bitrate= 547.8kbits/s frame= 130 fps= 19 q=29.0 size= 193kB time=2.84 bitrate= 557.5kbits/s frame= 136 fps= 18 q=29.0 size= 211kB time=3.04 bitrate= 570.0kbits/s frame= 144 fps= 18 q=29.0 size= 242kB time=3.30 bitrate= 599.5kbits/s frame= 152 fps= 17 q=30.0 size= 261kB time=3.57 bitrate= 598.6kbits/s frame= 157 fps= 15 q=-1.0 Lsize= 368kB time=5.21 bitrate= 579.3kbits/s video:302kB audio:61kB global headers:0kB muxing overhead 1.416371% [libx264 @ 0x99e1020]frame I:1 Avg QP:27.22 size: 8720 [libx264 @ 0x99e1020]frame P:48 Avg QP:25.15 size: 3759 [libx264 @ 0x99e1020]frame B:108 Avg QP:30.10 size: 1105 [libx264 @ 0x99e1020]consecutive B-frames: 0.6% 11.5% 28.8% 59.0% [libx264 @ 0x99e1020]mb I I16..4: 28.5% 47.6% 23.9% [libx264 @ 0x99e1020]mb P I16..4: 0.8% 1.3% 0.5% P16..4: 50.6% 17.7% 13.1% 0.0% 0.0% skip:15.9% [libx264 @ 0x99e1020]mb B I16..4: 0.2% 0.3% 0.1% B16..8: 44.0% 1.2% 2.6% direct: 5.1% skip:46.5% L0:45.5% L1:51.0% BI: 3.5% [libx264 @ 0x99e1020]final ratefactor: 23.51 [libx264 @ 0x99e1020]8x8 transform intra:49.9% inter:67.9% [libx264 @ 0x99e1020]direct mvs spatial:98.1% temporal:1.9% [libx264 @ 0x99e1020]coded y,uvDC,uvAC intra: 54.7% 76.1% 41.4% inter: 17.1% 24.4% 7.8% [libx264 @ 0x99e1020]i16 v,h,dc,p: 18% 52% 5% 25% [libx264 @ 0x99e1020]i8 v,h,dc,ddl,ddr,vr,hd,vl,hu: 12% 22% 9% 7% 10% 10% 9% 8% 13% [libx264 @ 0x99e1020]i4 v,h,dc,ddl,ddr,vr,hd,vl,hu: 13% 18% 8% 8% 10% 13% 10% 9% 12% [libx264 @ 0x99e1020]Weighted P-Frames: Y:10.4% [libx264 @ 0x99e1020]ref P L0: 60.2% 15.3% 11.0% 7.6% 5.2% 0.7% [libx264 @ 0x99e1020]ref B L0: 72.6% 15.6% 11.8% [libx264 @ 0x99e1020]kb/s:471.17 Segmentation fault I'm wondering if anyone else has ran into similar issues. I wasn't able to find anything helpful via Google. Another question I have is if anyone knows of a company that offers paid support for FFMPEG. Thank you for your time.

  Read the article

• Why do some games randomly turn my screen a random solid color?

  - by Emlena.PhD

  When playing some games my computer will randomly have an error that I cannot fix without turning it off and back on again. The screen changes to one solid color, which varies (off the top of my head I can remember seeing solid green, magenta, etc..) and the sound blares a single tone. The sound sometimes briefly restores and I can still hear the game sounds and even hear and still be heard by people in my Mumble channel, but the screen doesn't right itself so I'm still blind. What's more is this happens in some games but not in others. While the game is actually running, not while I'm still in the menu. However, it does happen if I'm afk or idle but the game world is still rendering. Games where the error occurs: League of Legends World of Warcraft Trine The Sims 2 Dungeon Defenders Safe games: games where it has never occurred: Tribes: Ascend Star Wars: the Old Republic Battlefield 3 So relatively older games cause the problem while newer games do not? I cannot predict when it will happen, it just seems random. However, if it happens and I try playing the same game further after restart it does appear to occur more frequently after the first time. But if I switch to a safe game it doesn't continue happening. Both of my RAM sticks appear fine, flipped position or either one on their own and games still run, computer still boots. I would think over-heating, but then why not all games? ALso, sometimes it happens immediately after I start playing, within seconds of the 3D world booting up. I'm looking to upgrade very soon so I want to figure out what component or software is fubar and replace/repair it. Any suggestions or recommendations of tools would be helpful. Below is some system information. Dxdiag does not detect any problems. Operating System: Windows 7 Home Premium 64-bit (6.1, Build 7601) Service Pack 1 (7601.win7sp1_gdr.120305-1505) System Manufacturer: Gigabyte Technology Co., Ltd. System Model: EP45-UD3R BIOS: Award Modular BIOS v6.00PG Processor: Intel(R) Core(TM)2 Duo CPU E8500 @ 3.16GHz (2 CPUs), ~3.2GHz Memory: 4096MB RAM DirectX Version: DirectX 11 DxDiag Version: 6.01.7601.17514 64bit Unicode Graphics card name: NVIDIA GeForce GTX 285 Driver Version: 8.17.12.9610 (error has occurred w/several driver versions) Sound: I do not have a sound card, been using motherboard's built in sound)

  Read the article

• Why many applications close after opening a document or doing a specific actions?

  - by Mohsen Farjami

  I have some encrypted pdf files that have no problem and in my last windows, I could open them easily with Adobe Reader 9.2 and other pdf readers. But now, I can only open non-encrypted pdf files and one encrypted file with Adobe Reader. every time I open almost any encrypted pdf, it closes itself. Also, when I try to search a folder for a keyword with Foxit Reader, once it closed. This is not related to Adobe Reader, because I have the same problem with Word 2007. When I open a document, sometimes it closes instantly and sometimes it closes after a few seconds and sometimes it is stable. My windows is Fresh. I have installed it a few days ago. I have ESET Smart Security 5.2 and I have updated it today. OS: XP Pro SP3, RAM: 3 GB, CPU: 2 GHZ, HDD: 320 GB My installed applications: Adobe AIR Adobe Flash Player 11 ActiveX Adobe Flash Player 11 Plugin Adobe Photoshop CS4 Adobe Reader 9.2 Atheros Wireless LAN Client Adapter Babylon Bluetooth Stack for Windows by Toshiba CCleaner Conexant HD Audio Dell Touchpad ESET Smart Security Farsi (101) Custom Foxit Reader Framing Studio 3.27 Google Chrome Hard Disk Sentinel PRO HDAUDIO Soft Data Fax Modem with SmartCP Intel(R) Graphics Media Accelerator Driver IrfanView (remove only) Java(TM) 6 Update 18 K-Lite Mega Codec Pack 8.8.0 Microsoft .NET Framework 2.0 Service Pack 1 Microsoft .NET Framework 3.0 Service Pack 1 Microsoft .NET Framework 3.5 Microsoft Data Access Components KB870669 Microsoft Office 2007 Primary Interop Assemblies Microsoft Office Enterprise 2007 Microsoft User-Mode Driver Framework Feature Pack 1.0.0 (Pre-Release 5348) Mozilla Firefox 7.0.1 (x86 en-US) Notepad++ Office Tab FreeEdition 8.50 ParsQuran PerfectDisk 12 Professional Registry First Aid RICOH R5C83x/84x Flash Media Controller Driver Ver.3.54.06 Sahar Money Manager 2.5 Stickies 7.1d The KMPlayer (remove only) TurboLaunch 5.1.2 Unlocker 1.9.1 USB Safely Remove 4.2 Virastyar Visual Studio 2005 Tools for Office Second Edition Runtime Winamp Windows Internet Explorer 8 Windows Media Player 11.0.5358.4826 Windows XP Service Pack 3 WinRAR 4.11 (32-bit) WorkPause 1.2 Z Dictionary My startup applications: WorkPause USB Safely Remove TurboLaunch SunJavaUpdateSched Stickies rfagent Persistence ParsQuran Daily Verse ITSecMng IgfxTray HotKeysCmds Hard Disk Sentinel egui disable shift+delete CTFMON.EXE Bluetooth Manager Babylon Client Apoint AdobeCS4ServiceManager Adobe Reader Speed Launcher Adobe ARM What should I do to solve it? If you recommend installing Windows again, what guarantees that it won't happen again?

  Read the article

• windows 2008 R2 TS printer security - can't take owership

  - by Ian

  I have a Windows 2008 R2 server with Terminal server role installed. I'm seeing a problem with an ordinary user who is member of local printer operators group on the server. If the user opens a cmd window using ‘run as administrator’ they can run printmanager.msc without needing to enter their password again. In printmanager they can change the ownership of redirected (easy print) printers without problems. If, from the same cmd window, they use subinacl to try and change the onwership of the queue to themselves they get access denied: >subinacl.exe /printer "_#MyPrinter (2 redirected)" /setowner="MyDom\MyUsr" Elapsed Time: 00 00:00:00 Done: 1, Modified 0, Failed 1, Syntax errors 0 Last Done : _#MyPrinter (2 redirected) Last Failed: _#MyPrinter (2 redirected) - OpenPrinter Error : 5 Access denied so, same context, same action but one works and one doesn't. Any ideas for this odd behaviour? I'm using subinacl x86 on an x64 server as I can't find anything more up to date. I've tried with icacls and others but couldn't get them to do anything with printers. EDIT: added after Gregs comments regarding setacl below If I log into the TS server as Testusr and open Admin Tools Printer Admin (as administrator) and then type mydomain\testusr and the testusr's password, then I can change the ownership of the printer queue and set testusr as the owner. However if I open cmd as administrator and, again, type mydomain\testusr and the users password when I try to change the ownership of my redirected printer I get the following: C:\>setacl -on "Bullzip PDF Printer (12 redireccionado)" -ot prn -actn setowner -ownr n:mydom\testusr WARNING: Privilege 'Back up files and directories' could not be enabled. SetACL's powers are restricted. WARNING: Privilege 'Restore files and directories' could not be enabled. SetACL's powers are restricted. INFORMATION: Processing ACL of: <Bullzip PDF Printer (12 redireccionado)> ERROR: Enabling the privilege SeTakeOwnershipPrivilege failed with: No todos los privilegios o grupos a los que se hace referencia son asignados al llamador. [meaning not all referenced privs or groups are assigned to the caller] SetACL finished with error(s): SetACL error message: A privilege could not be enabled maybe I'm getting something wrong but if the built in windows tool can do it with just membership of the 'print operators' group then setacl should be able to as well, no? However setacl seems to depend on other privileges, which in reality are not required to do this.

  Read the article

• Nginx giving a lot of 502 errors

  - by Loki

  Since a while I have installed nginx and everything seemed to be working fine, recently I found out that about 20% of the time users are getting 502-errors. This is also noticable when Google tries to crawl my site in Webmaster Tools (from 10000 posts, approx. 2000 502 errors) At first I was thinking to disable nginx, but I'd really like to keep using it. I'm running it on a server with 2GB RAM and 4 Reserved CPU Cores. WHM/cPanel installed and Mod_Ruid2 enabled + DSO as a PHP Handler with APC caching installed. Is there anything I can change in the config, that can fix this? I have installed Nginx Admin in WHM and here is what's in the configuration editor screen: user nobody; worker_processes 4; error_log /var/log/nginx/error.log info; worker_rlimit_nofile 20480; events { worker_connections 10240; # increase for busier servers use epoll; # you should use epoll here for Linux kernels 2.6.x } http { server_name_in_redirect off; server_names_hash_max_size 10240; server_names_hash_bucket_size 1024; include mime.types; default_type application/octet-stream; server_tokens off; disable_symlinks if_not_owner; sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 5; gzip on; gzip_vary on; gzip_disable "MSIE [1-6]\."; gzip_proxied any; gzip_http_version 1.1; gzip_min_length 1000; gzip_comp_level 6; gzip_buffers 16 8k; text/plain text/xml text/css application/x-javascript application/xml image/png image/x-icon image/gif image/jpeg application/xml+rss text/javascript application/atom+xml; ignore_invalid_headers on; client_header_timeout 3m; client_body_timeout 3m; send_timeout 3m; reset_timedout_connection on; connection_pool_size 256; client_header_buffer_size 256k; large_client_header_buffers 4 256k; client_max_body_size 200M; client_body_buffer_size 128k; request_pool_size 32k; output_buffers 4 32k; postpone_output 1460; proxy_temp_path /tmp/nginx_proxy/; client_body_in_file_only on; log_format bytes_log "$msec $bytes_sent ."; include "/etc/nginx/vhosts/*"; } I hope someone can help me out. Thanks in advance!

  Read the article

• Google Chrome issues

  - by Ben Hooper

  I'm an avid user of Chrome and would defend it to the death but there is no denying that it has issues, and I've been experiencing a lot of them recently. Issues Stuck tabs Issue: Around 60% of the time (higher when the system has just started), when Chrome is launched, some or all of the pinned tabs and startup pages will get stuck in the counter-clockwise-rotating "contacting server" mode and never snap out of it. Fix: Quit and launch Chrome until they load properly (this really isn't good, as quitting and launching Chrome can and has cleared all pinned tabs). Extra Information: If you stop the loading and re-enter the URL then the page will load perfectly. The amount of pinned tabs or startup pages seems to be irrelevant, but I could be wrong.   "Downloaded/out of" Issue: Each item in the download bar has a downloaded status section, formatted as "downloaded/out of". Sometimes Chrome doesn't display the "out of" part.   Collapsed settings windows Issue: In Chrome version 19(ish)+, settings are configured via overlayed / popup windows. Sometimes, the window will open fully collapsed. Fix: Resize Chrome's window or open the developer tools. "Network Error" with large downloads Issue: Sometimes, when downloading large files (500MB+) Chrome will download the entire file, the download status will freeze (for example, "1 GB/1 GB") for a few minutes, report "Network error", and delete the .crdownload file. Extra Information: The same file from the same website on the same computer downloads perfectly in other browsers. The website and file type seem to be irrelevant.   Information: I've experienced some of these issues on my home PC and some on my work PC, both of which are Windows 7 Ultimate x64. The only things that link them are my Google account (all settings are synced). Updating Chrome hasn't worked. Most of these issues presented themselves around about version 17 and have continued right through to 21 (current). Uninstalling Chrome, deleting all data in %programFiles(x86)%\Google and %localAppData%\Google, and reinstalling hasn't worked. I have yet to see whether disabling all extensions would make a difference, but it's hard to diagnose as these issues don't occur 100% of the time.   In my case, I don't know if there's an actual solution. I'm just curious as to whether anyone else is having similar issues to those that I'm experiencing. At least then I'll know it's an issue with Chrome itself.

  Read the article

• WIndows 7 cannot boot - bootrec reports FS not found or corrupt

  - by purecharger

  For 3 days now I've been unable to boot into my Windows 7 partition, and all my research has been to no avail. I'm hoping someone here has more ideas on how to fix this. When I boot up now, I get the black screen with BCD error that says theres no valid file system or it may be corrupt (pardon my lack of detail, no copy/paste is available then). When I boot with the Windows 7 disc and go into repair tools, no operating system is found, and attempting to automatically repair the problem fails with Unknown Operating System (Unknown Disk) or something similar. When I drop into the command prompt, I am able to see and navigate my C:\ drive without issue. I attempt to use bootrec: C:\> bootrec /ScanOS Finds C:\Windows as a system partition. C:\> bootrec /RebuildBCD Fails with volume does not contain a recognized file system. please make sure that all required file system drivers are loaded and that the volume is not corrupted. So then I attempt to fix the bootsector: C:\> bootsect /nt60 C: /force Which completes successfully (sorry, no output..) Upon rebooting, I have the same problem. I've also tried all of the above after making my Windows partition active: C:\> diskpart DISKPART> select disk 1 DISKPART> select partition 1 DISKPART> active DISKPART> exit Then bootrec as above, both with and without a reboot after the DISKPART commands. Then I've also tried rebuilding the BCD store by hand: set systemdrive=C: set tempbcd=C:\boot\bcd.temp set tempfile=C:\boot\temp.txt bcdedit -createstore %tempbcd% bcdedit.exe -store %tempbcd% -create {bootmgr} -d "Windows Boot Manager" bcdedit -store %tempbcd% -create -d "Windows Vista" -application osloader>%tempfile% set /p winvistaguid= <%tempfile% set winvistaguid=%winvistaguid:~10,38% bcdedit -store %tempbcd% -set %winvistaguid% osdevice partition=%systemdrive% bcdedit -store %tempbcd% -set %winvistaguid% device partition=%systemdrive% bcdedit -store %tempbcd% -set %winvistaguid% path \Windows\system32\winload.exe bcdedit -store %tempbcd% -set %winvistaguid% systemroot \Windows bcdedit -import %tempbcd% However on the import, I get my familiar friendly message: volume does not contain a recognized file system. please make sure that all required file system drivers are loaded and that the volume is not corrupted I'm at my wits end here, and I cannot understand why Windows refuses to see this as a valid install. When I list the disk/partition in DISKPART, it shows up as NTFS and "Healthy", and I can navigate the directory structure from DOS with no problems. I really, really do not want to reformat and reinstall. I know this problem can be solved!

  Read the article

• Ubuntu 12.04 crash analysis - strange binary data on all open files at the moment of crash

  - by lanbo

  A couple of hours ago we got a system crash on Ubuntu 12.04. We checked all the log files and there is nothing suspicious to blame to. Last stuff that was logged was some dovecot activity. There are no kernel panic messages. Nothing. It is a new server (new hardware) we are testing before production. And because it is new hard, I'm suspicious the problem may be due to some faulty hardware. We already run memtester with no problem detected. I'll be happy to hear from other hardware testing tools (the machine has SSD). Anyway, the thing I wanted to ask you is a different one. The strange thing is on every open file at the moment of the crash we found the next sequence of symbols was written into them: "@^@^@^@^@^@^@...". For example, on the syslog log file we got: Apr 16 15:53:56 odyssey dovecot: pop3-login: Aborted login (auth failed, 1 attempts): user=<info>, method=PLAIN, rip=46.29.255.73, lip=5.9.58.177 ^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^ [these continues for about 1000 chars...] ^@^@^@^@Apr 16 15:55:12 odyssey kernel: imklog 5.8.6, log source = /proc/kmsg started. We got all these symbols in all open files. These include: syslog, mail.log, kern.log, ... But also on some logs that are output by php scripts run in CRONs from user accounts (not root). So, any idea why all open files got these characters written during the crash? This is pretty bad since the crash corrupted many files (we don't even know which other ones may be affected). We are suspicious that all open files (in write mode maybe) at the moment of the crash got all these symbols inserted. Why is that? BTW [in case it helps], the system automatically rebooted after the crash but Apache did not start. There were not traces in /var/apache2/*log why apache did not start. After running a "service apache2 start" it started with no problems. Also, we rebooted the machine manually and Apache also started on reboot. But it did not start after the crash and no errors were reported. Thanks guys!

  Read the article

• Radeon HD4850 serious issues when using DirectX 10

  - by ricsmania

  Hello, I have a problem with my video card. Whenever I run a DirectX 10 game, it works for a few seconds (10 or so) and then starts displaying nothing but big polygons. I have tested this with Crysis and Resident Evil 5, both have the same problems. The same games running under DirectX 9 work fine, except for some small black squares once in a while. I have the following specs: Asus P7P55D LE Intel Core i5 750 Sapphire Radeon HD4850 1GB 2x2GB Patriot Viper II Sector 5, DDR3 1600 MHz OCZ Stealth X Stream 500SXS 500W At first I thought it could be the video card overheating (it has stock cooling), but the game crashes even when it's running at 50 degrees C, and it's never been higher than 70. I also thought it could be the PSU, but as far as I know 500W is enough for this computer, especially because I haven't overclocked anything. My OS is Windows 7 X64 and I am using Catalyst 10.10, but I have also tried many older versions with no success. I don't think there is a problem with the card itself, or else it wouldn't run DirectX 9 games I believe. I have spent many hours searching for a solution but I couldn't, so any help is appreciated. Thank you. EDIT: I did some further investigation about the problem, and it seems taspeotis was right, it might be related to memory. I slightly underclocked the memory from 993 to 965 MHz and the problem went away completely. Both the black squares using DirectX 9 and the weird polygons using DirectX 10. I was using RE DirectX 10 Benchmark, as it consistently crashed around the same point, and now I can play the full benchmark with no artifacts at all. Unfortunately, the underclock has an obvious hit in performance. Although it's not critical, it's definitely noticeable. So, if the video memory test software showed no erros, but the card needs an underclock to work, what might be the problem? Temperature? Voltage? By the way, I couldn't find what the default voltage for this card is. And what is a good software to try and increase it? I tried Ati Tray Tools but it has a bug that increases the clock speed dramatically whenever I change something in the Overclock tab, so I'm afraid it might fry my card. Worst case scenario, if I don't find I solution I will try to slightly increase the GPU clock to compensate for the memory clock. Thank you again.

  Read the article

• WIndows 7 cannot boot - bootrec reports FS not found or corrupt

  - by purecharger

  For 3 days now I've been unable to boot into my Windows 7 partition, and all my research has been to no avail. I'm hoping someone here has more ideas on how to fix this. When I boot up now, I get the black screen with BCD error that says theres no valid file system or it may be corrupt (pardon my lack of detail, no copy/paste is available then). When I boot with the Windows 7 disc and go into repair tools, no operating system is found, and attempting to automatically repair the problem fails with Unknown Operating System (Unknown Disk) or something similar. When I drop into the command prompt, I am able to see and navigate my C:\ drive without issue. I attempt to use bootrec: C:\> bootrec /ScanOS Finds C:\Windows as a system partition. C:\> bootrec /RebuildBCD Fails with volume does not contain a recognized file system. please make sure that all required file system drivers are loaded and that the volume is not corrupted. So then I attempt to fix the bootsector: C:\> bootsect /nt60 C: /force Which completes successfully (sorry, no output..) Upon rebooting, I have the same problem. I've also tried all of the above after making my Windows partition active: C:\> diskpart DISKPART> select disk 1 DISKPART> select partition 1 DISKPART> active DISKPART> exit Then bootrec as above, both with and without a reboot after the DISKPART commands. Then I've also tried rebuilding the BCD store by hand: set systemdrive=C: set tempbcd=C:\boot\bcd.temp set tempfile=C:\boot\temp.txt bcdedit -createstore %tempbcd% bcdedit.exe -store %tempbcd% -create {bootmgr} -d "Windows Boot Manager" bcdedit -store %tempbcd% -create -d "Windows Vista" -application osloader>%tempfile% set /p winvistaguid= <%tempfile% set winvistaguid=%winvistaguid:~10,38% bcdedit -store %tempbcd% -set %winvistaguid% osdevice partition=%systemdrive% bcdedit -store %tempbcd% -set %winvistaguid% device partition=%systemdrive% bcdedit -store %tempbcd% -set %winvistaguid% path \Windows\system32\winload.exe bcdedit -store %tempbcd% -set %winvistaguid% systemroot \Windows bcdedit -import %tempbcd% However on the import, I get my familiar friendly message: volume does not contain a recognized file system. please make sure that all required file system drivers are loaded and that the volume is not corrupted I'm at my wits end here, and I cannot understand why Windows refuses to see this as a valid install. When I list the disk/partition in DISKPART, it shows up as NTFS and "Healthy", and I can navigate the directory structure from DOS with no problems. I really, really do not want to reformat and reinstall. I know this problem can be solved!

  Read the article

• Firefox can't establish a connection to the server at www.google.com

  - by Tom

  My home page in Firefox [v4.0] and Internet Explorer [v9.0.8112.16421, Update Versions RTM (KB982861)] is currently set to Google but when I depress the quick start icon to start up either browser, I am getting the following immediate results: Unable to connect (In Firefox) Firefox can't establish a connection to the server at www.google.com. The site could be temporarily unavailable or too busy. Try again in a few moments. If you are unable to load any pages, check your computer's network connection. If your computer or network is protected by a firewall or proxy, make sure that Firefox is permitted to access the Web. Internet Explorer cannot display the webpage What you can try: Diagnose Connection Problems More information This problem can be caused by a variety of issues, including: Internet connectivity has been lost. The website is temporarily unavailable. The Domain Name Server (DNS) is not reachable. The Domain Name Server (DNS) does not have a listing for the website's domain. There might be a typing error in the address. If this is an HTTPS (secure) address, click Tools, click Internet Options, click Advanced, and check to be sure the SSL and TLS protocols are enabled under the security section. For offline users You can still view subscribed feeds and some recently viewed webpages. To view subscribed feeds: Click the Favorites button , click Feeds, and then click the feed you want to view. To view recently visited webpages (might not work on all pages): Press Alt, click File, and then click Work Offline. Click the Favorites button, click History, and then click the page you want to view. Thankfully, I am able to use one browser that I have installed on my computer (Mathon v3.0.20.5000) to search online for technical assistance in this matter. I have seen several WinSock error issues mentioned; but, they are pointing to Windows XP and I am using Windows 7 Pro and remain uncertain whether anything identified as a fix for one OS will work in another. Things I've tried: HiJackThis Complete scan with Avira AntiVirus Premium. What am I overlooking? What should I do to address this problem?

  Read the article

• New Exchange 2010 CAS cannot find domain controllers

  - by NorbyTheGeek

  I am experiencing problems migrating from Exchange 2003 to Exchange 2010. I am on the first step: installing a new 2010 Client Access Server role. The Active Directory domain functional level is 2003. All domain controllers are 2003 R2. The only existing Exchange 2003 server happens to be housed on one of the domain controllers. It is running Exchange 2003 Standard w/ SP2. IPv6 is enabled and working on all domain controllers, servers, and routers, including this new Exchange server. After installing the CAS role on a new 2008 R2 server (Hyper-V VM) I am receiving 2114 Events: Process MSEXCHANGEADTOPOLOGYSERVICE.EXE (PID=1600). Topology discovery failed, error 0x80040a02 (DSC_E_NO_SUITABLE_CDC). Look up the Lightweight Directory Access Protocol (LDAP) error code specified in the event description. To do this, use Microsoft Knowledge Base article 218185, "Microsoft LDAP Error Codes." Use the information in that article to learn more about the cause and resolution to this error. Use the Ping or PathPing command-line tools to test network connectivity to local domain controllers. Prior to each, I receive the following 2080 Event: Process MSEXCHANGEADTOPOLOGYSERVICE.EXE (PID=1600). Exchange Active Directory Provider has discovered the following servers with the following characteristics: (Server name | Roles | Enabled | Reachability | Synchronized | GC capable | PDC | SACL right | Critical Data | Netlogon | OS Version) In-site: b.company.intranet CDG 1 0 0 1 0 0 0 0 0 s.company.intranet CDG 1 0 0 1 0 0 0 0 0 Out-of-site: a.company.intranet CD- 1 0 0 0 0 0 0 0 0 o.company.intranet CD- 1 0 0 0 0 0 0 0 0 g.company.intranet CD- 1 0 0 0 0 0 0 0 0 Connectivity between the new Exchange server and all domain controllers via IPv4 and IPv6 are all working. I have verified that the new Exchange server is a member of the following groups: Exchange Servers Exchange Domain Servers Exchange Install Domain Servers Exchange Trusted Subsystem Heck, I even put the new Exchange server into Domain Admins just to see if it would help. It didn't. I can't find any evidence of Active Directory replication problems, all pre-setup Setup tasks (/PrepareLegacyExchangePermissions, /PrepareSchema, /PrepareAD, /PrepareDomain) completed successfully. The only problem so far that I haven't been able to resolve with my Active Directory is I am unable to get my IPv6 subnets into Sites and Services Where should I proceed from here?

  Read the article

• Any way to recover ext4 filesystems from a deleted LVM logical volume?

  - by Vegar Nilsen

  The other day I had a proper brain fart moment while expanding a disk on a Linux guest under Vmware. I stretched the Vmware disk file to the desired size and then I did what I usually do on Linux guests without LVM: I deleted the LVM partition and recreated it, starting in the same spot as the old one, but extended to the new size of the disk. (Which will be followed by fsck and resize2fs.) And then I realized that LVM doesn't behave the same way as ext2/3/4 on raw partitions... After restoring the Linux guest from the most recent backup (taken only five hours earlier, luckily) I'm now curious on how I could have recovered from the following scenario. It's after all virtually guaranteed that I'll be a dumb ass in the future as well. Virtual Linux guest with one disk, partitioned into one /boot (primary) partition (/dev/sda1) of 256MB, and the rest in a logical, extended partition (/dev/sda5). /dev/sda5 is then setup as a physical volume with pvcreate, and one volume group (vgroup00) created on top of it with the usual vgcreate command. vgroup00 is then split into two logical volumes root and swap, which are used for / and swap, logically. / is an ext4 file system. Since I had backups of the broken guest I was able to recreate the volume group with vgcfgrestore from the backup LVM setup found under /etc/lvm/backup, with the same UUID for the physical volume and all that. After running this I had two logical volumes with the same size as earlier, with 4GB free space where I had stretched the disk. However, when I tried to run "fsck /dev/mapper/vgroup00-root" it complained about a broken superblock. I tried to locate backup superblocks by running "mke2fs -n /dev/mapper/vgroup00-root" but none of those worked either. Then I tried to run TestDisk but when I asked it to find superblocks it only gave an error about not being able to open the file system due to a broken file system. So, with the default allocation policy for LVM2 in Ubuntu Server 10.04 64-bit, is it possible that the logical volumes are allocated from the end of the volume group? That would definitely explain why the restored logical volumes didn't contain the expected data. Could I have recovered by recreating /dev/sda5 with exactly the same size and disk position as earlier? Are there any other tools I could have used to find and recover the file system? (And clearly, the question is not whether or not I should have done this in a different way from the start, I know that. This is a question about what to do when shit has already hit the fan.)

  Read the article

• Problem with several USB devices on Windows XP. How to diagnose USB device?

  - by Lukasz Baran

  Hello All, Recently I've bought some electronic devices (like e.g. Sony Ebook reader PRS-600 or HP PDA IPaq) which are connected to PC using USB ports. These devices have own batteries and they are recharged using USB. However, I am experiencing a problem with Ebook Reader and the similiar thing happens with my PDA (but in this case it's more rare). Sometimes, I am unable to make it start recharging, when it's connected to USB port. The LCD diode on my Reader lights up and the icon in the system tray appears. They both indicate that the device has been connected. However, the device should start recharching and it should appear on Windows XP as a 'explorable' device (just like pendrive it offers some HDDs). None of these happens:( This problem appears on two PCs - desktop and laptop. Both have Windows XP SP3 installed. And what's interesting and surprising to me is the fact that these devices sometimes work without any problems. I mean, I just plug them in and they work properly. Besides that, there are some computers (I have tested a variety of possible conditions) on which the problem does not appear! I am confused and, on the other hand, determined to find out what is the real cause of such strange behavior. Maybe I'm wrong but I always assumed that I'm using deterministic machines, but the described situation makes me feel like I was dreaming:) And that's why I'm asking you here. Are there any tools that could help me diagnose USB ports? Or maybe anyone knows the solution? I have a lot experience with low level programming (mostly from the times of MS-DOS applications), but I'm not an expert when it comes to WinXP technology. If this was a problem with network connection, I would know what to do - I know how to track network traffic, but with USB ports I feel powerless. I have a feeling that the problem may lie in a way WinXP handles USB devices. Personally, I hate auto-discovery and P'n'P features available in Windows. I know that some of may suggest to move to Linux or other *Nix system. Unfortunately, I have to use WinXP in my professional life, so it's rather impossible. Besides that, I don't consider XP as a total disaster. Any help from you will be appreciated!

  Read the article

• System failure - need diagnostic recommendation

  - by Ladislav Mrnka

  I have big problem with my computer. Configuration is: Intel i7 + 6x2GB OCZ DDR3 Motheboard: Asus P6T Deluxe V2, HDD controller configured to AHCI Main drive: OCZ Vertex 2 (SSD) - contains all installed programs and system Second drive: Samsung SpinPoint - contains User profiles, ProgramData, virtual machines and databases Third drive: Samsung SpinPoint - data drive + backups OS: Windows 7 Ultimate x64 I have never had any problem with this computer until now. During weekend my computer completely crashed without any reason. Each time I tried to boot to Windows I got BSOD with message BAD_SYSTEM_CONFIG_INFO and automatic restart (I didn't install any new SW or HW). But after restart main OCZ drive was disconnected (not detected by BIOS). When I turned off and on computer, the drive was again connected. It also happend every single time I tried to repair installation somehow. It ended with some error and after restart drive was disconnected. The only thing which worked was format + fresh install. After installing almost everything I wanted to install Visual Studio 2010 Ultimate (complete installation without SQL Server Express). During installation of VS itself I always get BSOD - it is too fast so I'm not able to read description. After restart it searches for all disk drives for really long time and sometimes it changes boot drive so the system is not able to start - Bootmgr not found. After reconfiguring BIOS the system starts. There is no event describing the failure in Event viewer. Installing VS 2010 is absolutely necessary for me. I need help with diagnostic. I need to find where is the problem - I expect that the problem is in OCZ drive or in HDD controller on motherboard but I don't know how to find it. All components still have valid warranty. Can you recommend me some approach or tools to find the problem? Edit: I'm still looking for source of the problem. New information is that Windows are not able to perform check disk (Chkdsk) on the SSD system drive. After restarting it always starts checking drive and in part where files are checked it fails with BSOD - BAD_SYSTEM_CONFIG_INFO. After next restart and skipping check disk tests the system runs.

  Read the article

• When upgrading from Vista to Windows 7 on a DELL laptop, how do I know which drivers to reinstall an

  - by msorens

  According to Dell's upgrade page for Vista to Windows 7, after using the upgrade assistant the final step is to install drivers. They refer to this page for the order of driver installation, listing 9 items. From there I go to the Dell Drivers and Downloads page, enter my system tag, and get a list of the downloads available for my specific box. That page, by the way, has a link to driver install instructions that lists 10 rather than 9 items. Going to Drivers Help in the side panel and clicking on "In what order should drivers be installed?" shows yet a third list, this one containing 13 items. Not surprisingly, the order of these 3 lists of drivers are not quite the same for the common items! Furthermore, of the 26 files Dell's site recommends for my machine, there are several not shown on any of the 3 lists! I can make determinations for some of these: 6 of them are "applications" so I know which of those I want and that they could probably be safely installed after all drivers. BIOS: I would think this should be unaffected by an OS upgrade so could be skipped. Two tools in the diagnostics category: could probably be done after all drivers. That leaves just a CD/DVD driver and a webcam driver unaccounted for. So my two related questions are these: How critical is the driver installation order and which one do I follow? (Keep in mind this is for an upgrade, not a fresh install.) Where in the order do I insert the CD/DVD and the webcam drivers (if needed) ? Dell's driver download page provides (in theory) the list of all downloads relevant to my specific machine, via the service tag. But do I actually need to reinstall all of them? some? none? How does one determine this? They do label each with Recommended or Optional, so do I need to reinstall all the recommended ones? (Part of the reason for my perplexed frown is that I wonder why I would need to reinstall a CD/DVD driver since I would already be using the drive to install the OS!)

  Read the article

• how do i install intermediate certificate

  - by getmizanur

  I have installed private key (pem encoded) and public key certificate (pem encoded) on amazon load balancer however when i check the ssl with site test tool (http://www.networking4all.com/en/support/tools/site+check/), i get the following error Error while checking the SSL Certificate!! Unable to get the local issuer of the certificate. The issuer of a locally looked up certificate could not be found. Normally this indicates that not all intermediate certificates are installed on the server. i converted crt file to pem using these command from this tutorial openssl x509 -in input.crt -out input.der -outform DER openssl x509 -in input.der -inform DER -out output.pem -outform PEM during setting up of amazon load balancer only option i left out was certificate chain (pem encoded) however this was optional. could this be cause of my issue? and if so i how do i create certificate chain? for the last question i have tried googling however i'm getting more confused than before. please help many thanks in advance. UPDATE @all thanks for the helpful advice. if you make request to verisign they will give you a certificate chain however this chain includes public crt, intermediate crt and root crt. make sure to remove the public crt from your certificate chain (which is the top most certificate) before adding it to your certification chain box of your amazon load balancer. if you are making https request from an android app then above instruction may not work for older android os such as 2.1 and 2.2. to make it work on older android os [https://knowledge.verisign.com/support/ssl-certificates-support/index?page=content&id=AR657&actp=LIST&viewlocale=en_US]. on this link click on "retail ssl" tab and then click on "secure site" "CA Bundle for Apache Server". copy and past these intermediate certs into certificate chain box. just incase if you have not found it here is the direct link [https://knowledge.verisign.com/support/ssl-certificates-support/index?page=content&id=AR1409] if you are using geo trust certificates then solution is much the same for android devices however you need to copy and past their intermediate certs for android. PS: sorry for the long urls however "new users can only post a maximum of two hyperlinks"

  Read the article

• Frequent and weird wifi disconnections

  - by Sidou

  How would you explain, troubleshoot (and solve) the following problem? Wifi ADSL modem router D-link 2640R installed in living room at about 1.8m height. Working fine, synchronising and getting/serving stable internet connection. First situation: -Laptop 01 in other end of the house, let's say in room01 southern to the living room, distant by about 15m. Getting stable signal of good to very good quality. No disconnection. -Laptop 02 in room02 opposite to room01 (5m West) which makes it almost at the same distance and direction from the router located 15m North. Getting stable signal of good to very good quality. No disconnection. Second situation: -Laptop 01 moved to room03 Northern to the living room (actually just 3m behind the wall where the router lies). Getting stable signal of excellent quality. No disconnection. -Laptop 02 still in room02 but now experiences frequent disconnections (actually almost impossible to get the Internet even though the signal level is still very good. Either no Internet with the wifi icon appearing connected to access point or no connection established at all which happens every 2 minutes and that means virtually no Internet at all as I can just get a timeframe of 1 minute or so to load any website or even get to the router's web based control panel. If Laptop 01 is completely shut down or its wifi adapters shut down or even still working but its wifi MAC address forbidden, then Laptop 02 has no problem at all. If Laptop 02 is moved to a nearer location to the router, in the living room for instance, then no connection problem occurs even if Laptop 01 is also connected. And also if we move back Laptop 01 to its original location (room 01), then no problem as well. I'm completely lost and don't know how to address this issue. I tried to change the Wifi channel and even tried the auto channel scan but that didn't solve it. I know that the problem is probably coming from Laptop 01 being in its new location or some sort of interference as the problem occurs only under the described condition but I have no idea how to solve it! I also scanned the neighborhood for wifi jam using InSSIDer, there are few other access points but they don't seem to affect the situation. Any ideas about the steps to follow or tools to use ?

  Read the article

• Well....a ghost lives in my server...

  - by tsgiannis

  Hello to every body and greetings from Greece I have a rather unusual situation and i am running out of ideas. I have this old server (IBM x205 - P4 2.4Ghz,3xSCSI 36gb) and i was about a year ago i decided to use it as an additional domain controller,fax & file server...for this task i had a Delock 70154 SATA card along with 2x320 SATA II HDDs Everything was going super smoothly until about 3 weeks ago. I was on a trip and i was informermed when i got back that the server was found frozen...well i considered it was a glitch since a simple powerdown power up fixed everything.Again 2 weeks ago another freeze situation....it got suspicious but again power down power up everything was running.... Last again it frozen and when i power it up it came with a message that the Domain services could not start due to NTDS corruption....booting in safe mode revealed that there was an issue with the SATA Raid (degraded). After a lot of searching i degraded the server...cleaned Active Directory and pulled both HDDs out (one of these was really BAD ) and recovered my files (i had some problems with ho Delock handles the redudant HDD). Right now my server is vanilla simple...with only what the factory installed and here is where the fun begins. Everyday when i arrive at the office i find this particular machine dead..and i mean total dead...just a black screen and nothing else...the cpu fan is working ,the psu is working .keyboard and mouse are dead(they also lock my kvm) ...network is dead.... the machine is DEAD. I power it down forcilly ...i power it up and for the 8 hours i am in the office it works,either idling or running some kind of diagnostic...when i leave the office after some time..it maybe half an hour ...it maybe 4 hours the machine dies...at least this is the information the event log shows (" the previous shutdown at xx:xx:xx was unexpected) Well i must admit i am runnig out of ideas.... I have tried Memtest....nothing Passmark burn in test.....nothing Carefull study of the event log.....nothing Set Instead of restart..BSOD....nothing Power sceheme to sleep...all set to never. i know there are a lot of other tools that heavily stress a machine like occt but .... the machine is old...today i will give them a try nevertheless ..... One idea is to reformat it...but ... i really like to find what is causing this because i could get to a situation that everything is working for a while and kaboom...one day again is dying.. I really need a helping hand and every opinion / idea is well welcomed.... iknow the obvious solution is to never leave the office but....i have a life...sory server...:) P.S this situation with the machine dying some time after is going on for about one week...everyday i would set either the RAID to rebuild....or to copy/recover files and while everythig was working

  Read the article

• How can I remove old log entries from a log file and archive them somewhere else in Linux?

  - by Mike B

  CentOS 4.x I apologize in advance if this is not the appropriate place to ask this question. It pertains to a linux server / IT admin task. I've got a log file on an old CentOS 4.x server and I want to remove log entries older than a certain date and place them in a new file for archive. Here's an example of the log format: 2012-06-07 22:32:01,289 ABC:0|Foo|Foo2|4.4|1234|Some Event|123|blah blah blah 2012-06-07 22:32:03,289 ABC:0|Foo|Foo2|4.4|1234|Some Event|123|blah blah blah 2012-06-07 22:32:04,289 ABC:0|Foo|Foo2|4.4|1234|Some Event|123| 2012-06-07 22:32:10,289 ABC:0|Foo|Foo2|4.4|1234|Some Event|123|blah blah blah 2012-06-07 22:32:12,289 ABC:0|Foo|Foo2|4.4|1234|Some Event|123|blah blah blah 2012-06-07 22:32:15,289 ABC:0|Foo|Foo2|4.4|1234|Some Event|123| 2012-06-07 22:32:40,289 ABC:0|Foo|Foo2|4.4|1234|Some Event|123|blah blah blah 2012-06-07 22:32:58,289 ABC:0|Foo|Foo2|4.4|1234|Some Event|123|blah blah blah 2012-06-07 22:33:01,289 ABC:0|Foo|Foo2|4.4|1234|Some Event|123| 2012-06-07 22:33:01,289 ABC:0|Foo|Foo2|4.4|1234|Some Event|123|blah blah blah 2012-06-07 22:33:02,289 ABC:0|Foo|Foo2|4.4|1234|Some Event|123| Essentially, I'm looking for a one-liner that will do the following: Find any events older than a provided YYYY-MM-DD and remove them from the primary log file. Take the deleted events from step 1 and put them in a new log file (Optional) Compress the new archive log file holding the deleted events. I'm aware that there are log rotate tools that do this but this should just be a one-time task so I'd prefer not to set that up. Additional notes: If the date part it tricky or too resource intensive, an alternative would be to just keep the last X number of lines and move the rest. I was originally thinking of something like tail -n 10000 > newfile.txt but that would mean moving the "good" logs to a new file and then doing a name swap... and then I'd still need to remove the "good" entries from the archive. This particular log file is pretty large (1 GB) so I'd prefer the task to be as resource and time efficient as possible. The extra pipes in the log concern me and I'm not sure if I'd need extra protection in the commands to avoid that from causing problems.

  Read the article

• FTP server questions

  - by Brad

  I'm currently trying to set up a home FTP server using debian and proftpd and I've run into a problem that has me confused. I have most things set up already, I believe, but I cannot access my ftp server using my external ip. I've forwarded the correct port on my router and I've checked http://www.yougetsignal.com/tools/open-ports/ to be sure that it is, in fact, opened. I've used telnet locally on my server to check that the port accepts connections. I am able to use ftp via LAN. But, I still cannot access anything externally. I'm thinking that there's still some router configuration to be done in order to fix this, such as routing all connections on my ftp port to my server via the internal ip, but I can't find any option on my router to do this. Is this a necessary step? There is an option to use DMZ hosting, but I'd rather avoid it if possible. I can provide additional information as requested, please let me know any information that you think could help at all. Thanks. -Brad PS - I have a Telus Actiontec Modem/Router Update - !! Trying my ftp server out at work, worked! I guess I did set it up correctly after all. What is confusing me, though, is why doesn't the server allow me to connect locally anymore? That seems very weird to me. Also, I don't really understand why I am denied outright if I attempt to connect from the same network using the external address. I'll look into it more when I get home, but thank you guys for your help. Update 2 - I found the problem with not being able to connect locally anymore. I was setting the masquerade address to my external IP and for some reason that was causing it to hang on MLSD when I connected using my LAN address. I've removed the masquerade address and I'm going to check if I need it at work tomorrow. I'll update this page if I find anything.

  Read the article

• Dlink search is hijacking my browser

  - by James

  For months now "DLink search" has been hijacking my search engines. I use google chrome, and I have organized my search engines in the handy dandy "manage search engines" tool about a TRILLION times. It never even says D-link is hacking my search engines. It does not show up! I have read many posts on this forum and others saying that to fix this problem from internet explorer: Setup, internet options, yadayada, magical fairies, and you are solved, but my browser is google chrome! How am I supposed to do this from there! I do not know how to re-setup my Dlink router, which is the cause of the problem! HOW? In those posts with the magical fairies fixing it, HUNDREDS responded saying, "yep, those fairies definitely fixed it right. :)" These people were so satisfied. IT WORKED FOR THEM, WHY NOT ME. I look at it and go ":(" because it does not help me. There are no options for anything to do with this in GOOGLE chrome. PLEASE EXPLAIN and HELP. I see no "SETUP" option, no "Internet Options" button, no anything. BTW the exact posts are these: "Uncheck Advanced DNS in the router internet setup. This will take care of it. I had this problem with my DLink router before." "I had this issue with my DIR-655 and unchecking the Advanced DNS setting in Setup - Internet - Manual Internet Connection Setup fixed it." "If this is just internet explorer, you can go to Tools Internet Options or Internet Options in Control Panel. From here, go to the advanced tab and click the Reset button." "I would set the router's DNS to a site like OpenDNS, and I would ensure the machines are set to get their DNS settings via DHCP or set the machine's DNS setting to OpenDNS. If the router's DNS looks like it was messed with, some bad software know the default passwords for routers and could have changed it. If you don't already I would make sure the password to the router is not default or easy to guess. I've had spyware change a machine's DNS, but the fact it is happening on all machines makes me wonder if it is the router." "Something got into your router and changed the dns server most likely, do a hard reset of the router and then change the password to something strong. Also check for a firmware update for the router and apply it as soon as possible."

  Read the article

• New harddrives failing within weeks.

  - by Jason Kealey

  I've experienced 8 hard disk failures in 3 months and have tried many things to solve the issue permanently but I have failed. I would like to know if you have any advice for me. System was running Win XP on an Asus P5W-DH Deluxe. I have setup a RAID-1 array. I started out with 2 x 500 GB 7200RPM Western Digital drives. One died. I took it out to RMA it. On the same day, the router was fried. Assumed a power surge occurred; connected an older UPS to protect the system. Once I got my hands on an identical disk, I installed it. The RAID array was rebuilt. A few days later, the other one died. Assumed the rebuild caused it to fail. Took it out for RMA. Before the other one arrived, the remaining one died. I then discovered I could re-enable them using the Intel Matrix Storage Manager. I re-enabled both and the system seemed fine for a week, until both died again. I got two new 1.5 TB 7200RPM Seagate drives and re-installed Windows 7. Also replaced the UPS and power supply. They both died again. The voltage on the plug is stable between 120 and 122V as per the UPS. None of the other devices have had any problems (monitors, etc.). At this point, I see two options: a) electrical issue in the house that was, for some reason, not blocked by the UPS. b) something else inside the system causing surges? motherboard? onboard raid controller? Failures happen fairly quickly, between 2 and 14 days after I fix the previous issue. I just gotten a new computer (Core i7) to replace it. If it is stable, I can determine that b) was the problem. If it fries its hard drive again, I can determine that it is an electrical issue in the house. Do you have any other thoughts? Any tools I can run on the drives that failed to get more information about the original SMART event history?

  Read the article

< Previous Page | 557 558 559 560 561 562 563 564 565 566 567 568  | Next Page >