Search Results

Search found 18214 results on 729 pages for 'computer industry'.

Page 562/729 | < Previous Page | 558 559 560 561 562 563 564 565 566 567 568 569  | Next Page >

• TrueCrypt - "Warning! Password locked: Fixed disk0" error message on boot

  - by Tibi

  TrueCrypt - "Warning! Password locked: Fixed disk0" error message on boot. When i start my laptop (Acer TravelMate 2410). after the starting memory check, the screen goes full black, and a message appears for about 3 seconds: Warning! Password locked: Fixed disk0 and after that, disappears, and next message comes out: Operating System Not Found and all stops here. Windows Xp was installed on it, before this came. TrueCrypt cd (witch was made during the process of full encryption) is not working, not in restoring MBR, no even in decrypting my drive - completely useless. Note: I detected some short of boot sector errors (i dont know the amount) on my drive before this happened. Please, i would greatfully thank every comment, or suggestion, because my computer is unusable now. The HDD is a Samsung HDD, 160Gb. Other preferences: Acer TravelMate 2410 Notebook, 2 Gb RAM, 1500 Mhz Intel Celeron M processor. Regards

  Read the article

• Vertically resize two windows at same time?

  - by Guy

  I love the new feature in Windows 7 where I can grab the title bar and "slam" a window against the right edge of the computer and it will size that window to the right half of the screen. I can then grab another window and do the same against the left side of the screen. Once I've done that I often find that one of those windows needs a bit more horizontal space and the other can do with less. So I grab the edge in the middle of each window and resize that window so I can most efficiently use my screen space. Problem is that I have to do this twice, once for each window. Is there a way to grab the inside vertical edge of both windows at the same time so that I can make one wider and the other smaller at the same time?

  Read the article

• Setup IPv4 local on IPv6 VPS

  - by A.D.

  I have a dedicated server running multiple IPv6 only OpenVZ containers. I want them to be able to communicate with the IPv4 internet, but I realized that isn't going to be possible with IPv6 only. So they need to have an IPv4 address as well, not sure if a local address will work for it, but pretty sure it should. I added 169.254.1.100 in the container .conf file, but when I try to start it, I get this : Adding IP address(es): (the IPv6 address) 169.254.1.100 arpsend: 169.254.1.100 is detected on another computer : 00:04:9b:f2:b0:00 vps-net_add WARNING: arpsend -c 1 -w 1 -D -e 169.254.1.100 eth0 FAILED I did a lot of research, and searched serverfault before posting this, but found nothing relating to this.

  Read the article

• Cannot connect to FTP server from external host

  - by h3.

  I have a FTP server (vsftpd) setuped on a Linux box (Ubuntu server). When I try to connect with a computer on the same network everything works fine as expected. But as soon the IP is external it won't connect.. I first assumed the port was blocked, but then: localserver:$ sudo tail -f /var/log/vsftpd.log Wed Jan 13 14:21:17 2010 [pid 2407] CONNECT: Client "xxx.xxx.107.4" remotemachine:$ netcat svn-motion.no-ip.biz 21 220 FTP Server And it hangs there. Do any ports other than 21 need to be open?

  Read the article

• Problem deleting files in Windows 7

  - by Alex Yan

  Happens sometimes but frequently enough to be a pain in the bum. I press Del or Shift + Del but the file stays there. Then when I try to delete it again, it says that I need permission from the Admin. For it to be deleted, usually I have to restart my computer List of things I've tried: I have admin privileges Hasn't happened since I reinstalled Windows and another form of this happened in my install before the last one I tried takeown in cmd but it says ERROR: Access is denied The files sometimes disappear by themselves after 2 mins or so Refreshing the folder doesn't do anything Unlocker doesn't work either. It asks me if I want to delete it the next boot Windows 7 x64 Pro HDD: Fujitsu MHZ2320BH G2 ATA 320 GB 8MB Buffer 5400 RPM

  Read the article

• Remote HTTP to FTP

  - by jamd12

  I am on a very slow download with the internet that I have and unfortunately I only have access to expensive and slow wireless or satelite. I have set up an FTP with a computer supplier locally who has a nice 2 Mbps speed and am trying to set up a way of adding links remotely (Hotfile, rapidshare, Fileserve, etc.) so that they can be downloaded onto the FTP and then transfered a few times a week manually onto a portable HDD. On my home PC I use Internet download manager for all my downloads. Is there a simple way that I can add links remotely to Internet Download Manager on the FTP or perhaps another solution? The OS on the FTP is Linux - I use Windows XP SP3 and Windows 7. I have not used FTP very much before so any suggestions on how best to do this would be much appreciated.

  Read the article

• ssh can't connect after server ip changed

  - by Kery

  I have a server with ubuntu installed. After I change the network configuration and restart server, ssh client can't connect server any more. But in the server I can use ssh client to connect itself and the netstat command shows that sshd is listening port 22. And in my computer (win7) ping command is OK to server's new IP. The configuration in /etc/network/interfaces is: auto eth0 iface eth0 inet static address 10.80.x.x netmask 255.255.255.0 gateway 10.80.x.1 I'm very confused about this. Hope somebody can give me some idea. Thank you in advance!!!

  Read the article

• How do I reinforce compression options?

  - by Gooberpatrol66

  Shortly after I got my computer, I enabled NTFS compression on it, selecting the option to compress "all files and subfolders". I recently noticed that several folders on my PC are not compressed anymore, including "Program Files" and "Windows". I suspect this happened when I installed Windows 8.1. The problem is, the only way I can think of to fix this would be to uncheck the tick box under "Properties" for my drive, thus decompressing everything on my drive, and then re-check it with the "all files and subfolders" option. Is there a way to compress all the uncompressed folders without first decompressing the compressed folders?

  Read the article

• Bug: unable to handle kernel NULL pointer dereference at

  - by maria

  I have recently installed new system on my disc, Ubuntu 12.04. Installation proceeded without problems, I started installing additional software and put data from other discs. I had already two times bug report, it was quite long, and I have no idea how to acces to log file (which probably is somewhere saved) and since I had to switch off the computer using the button, anything else was possible, here is just a small part of it (what I've noted on paper) could not write bytes: Broken pipe speach dicpatcher disabled: edit etc/default/speach-dispatcher saned disabled: edit .... and than: BUG: unable to handle kernel NULL pointer dereference at 0000009c I've run Memory test in GRUB, everything is fine. First time it occured when I was using rsync, second time when I was trying to install texlive. Should I install whole system once again? Or can it be hardware problem? Or something else? If there is any hardware details which may be relevant, please ask, since I have no idea what is happening, I don't know what kind of information could be useful. Thanks P.S. dmesg output:

  Read the article

• Windows 7 - Static DHCP server address with dynamic IP Address

  - by mkstreet

  Is this possible? On my LAN, I would like to setup the network properties such that the DHCP server's address is static. However, I want that server to hand out the IP Addresses and DNS addresses dynamically. The reason is that some devices on the LAN will try to behave like a DHCP server. For example, we use software to push images to computers on the LAN (our computer software configurations are centrally managed). When that imaging distribution software happens to be running, the machines being imaged will get confused as to which device is the DHCP -- the real one or the machine that is sending them the image. So, to remove the confusion, I would like to setup my Windows 7 images such that the DHCP server address is statically assigned. And then that server would assign the IP Addresses and the DNS addresses dynamically.

  Read the article

• Why won't Windows use the other CPU cores?

  - by revloc02

  In Windows Task Manager the Performance tab shows the first CPU maxed out, the other 7 just idling along with the occasional spike. What gives? More info: I've got 8GB and only 4.5GB are being used. The Processes tab has no indication of any process hogging processing power. In fact System Idle Process is 98-99. When I program stuff and have like 8 to 12 applications going (several directly unrelated to programming of course) my computer slows to a crawl. Sysyem Info: Intel Core i7-2600K Processor (quad-core with hyper-threading), 8GB RAM, Intel BOXDZ68BC LGA 1155 Motherboard, 500GB HDD

  Read the article

• Do I have a bad SD card?

  - by User1

  I'm trying to copy data from my computer to an SD card. After a few hundred megs, I keep getting the following errors in dmesg: [34542.836192] end_request: I/O error, dev mmcblk0, sector 855936 [34542.836284] FAT: unable to read inode block for updating (i_pos 13694981) [34542.836306] MMC: killing requests for dead queue [34542.836310] end_request: I/O error, dev mmcblk0, sector 9280 [34542.837035] FAT: unable to read inode block for updating (i_pos 148486) [34542.837062] MMC: killing requests for dead queue [34542.837066] end_request: I/O error, dev mmcblk0, sector 1 [34542.837074] FAT: bread failed in fat_clusters_flush [34542.837085] MMC: killing requests for dead queue These were all files I copied from a smaller SD card. I just want to transfer them to my new, larger card for my phone. I tried the same experiment with different files on a different machine and the card failed again. Reading data from the old card went fine. My systems are older and the new SD card is new (16GB Class 4). Could this be that my computers are too old? Is there a definitive test to verify if my SD card is bad?

  Read the article

• Ubuntu 11.04 64bits Keeps Randomly Freezing

  - by user971602

  This has been a real headache for me since the number of freezes has increase from twice a week to about 1 or twice a day. The system just halts and nothing can be done but hitting the restart button. At the beginning I thought it was related to Flash since I was getting random freezes when playing full screen flash videos online. I also thought it could be the wireless pci card. But the system has freezed using browsing around GNOME. The truth is, the freezes are really random and strange. I checked this thread Ubuntu keeps randomly freezing and try to ssh my computer using another one, but I could not ssh since it was really totally frozen. NumLock or CapsLock wasn't responding or blinking. Since I could not ssh I, also ignored this article https://wiki.ubuntu.com/X/Troubleshooting/Freeze According to my wife, the system has also halted under Win7 Pro 64bit but with less frequency. Here is my system configuration Intel Core i7 2600k ASRock Z68 Extreme3 gen3 Motherboard Crucial M4 128GB CT128M4SSD2 SSD WD Caviar Green WD10EADS 1TB SATA II G.SKILL Ripjaws X Series 8GB (2 x 4GB) DDR2 OCZ ModXStream 600W Power Supply Rosewill RNX-N300X PCI Wireless Adapter No external Graphics Card I remove the Wireless card and used Ethernet to see if the problem was the that, but I got a freeze after doing that. I also ran memtest86 and everything was ok. The only other thing I might suspect of is the SSD. I will try to clone the SSD to a HDD to see if that solve the problem. At this point I am stuck with the freezes. Do anyone have a clue of why this is happening and how can i solve this?

  Read the article

• Backup folder on sometimes attached external usb harddrive

  - by ctrler

  My girlfriend no longer has space her laptops drive to store her photos. The drive she has now is 750GB, so to go to a bigger drive would be expensive, as there isn't many 1.5tb 2.5 inch 9.5mm hdd on the market (as of now, there is only one). Because of that, I am thinking of moving her pictures to a cheap external usb hdd. As of now, I'm automatically backing up her important folders (My Documents, Pictures, etc.) using Windows 7 default backup software to a network drive. My problem is that I don't know of a good solution to automatically backup a folder residing on an usb disk. The usb disk won't be attached to the computer all the time, so I can't just treat it as a normal backup folder. Sometimes the backup would run and the folder would not be there! Anyone knows any software or methodology to backup folders on external usb hard drives that are not always present? Thanks

  Read the article

• Suggestions for hosted file sharing services

  - by Jon

  Before I pose my question, I will give some insight as per my scenario: I work for a small business (cost is an important factor) Our bandwidth is limited and would not support an in-house FTP server We need to share files (mostly pdf, inDesign, Illustrator documents) to our clients, and as we expand, we are finding that our current locally-hosted FTP solution is too slow and is becoming a detriment to our sales team. What we need is a remotely hosted solution to share files with our clients, specifically with the following features: Greater than 100gb of secure storage The Ability to distribute unique log in credentials to clients, granting access to a personalized directory or folder, while limiting access to other files on the server. A relatively simple web-based UI for clients with limited computer knowledge We have considered a dedicated remote server, and web-based services (box.net, yousendit.com, onehub.com, filesanywhere.com) but I am unsure as per the direction we should be taking - have I left another solution out? What would you suggest? Thanks in advance.

  Read the article

• Configuring MPI on 2 nodes

  - by Wysek

  I'm trying to create really simple "cluster" from 2 multicore computers using openmpi. My problem is that I can't find any tutorials on that matter. I don't want to use torque because it's not necessary in my case nevertheless all tutorials give configuration details either about torque or mpd (which doesn't exist in openmpi implementation). Could you give me some tips or links to appropriate manuals? Steps I've already completed: - openmpi installation - network configuration (computers see each other) - ssh password-less login to second computer I tried using machinefiles without further configuration and with just 2 IPs in it. But jobs don't seem to start at all after initialization part. (MPI seems to work because I'm able to scatter jobs on multiple cores of both computers without communication between them).

  Read the article

• Not recognized as operating system on startup

  - by mastabruce

  I am new to Ubuntu and just decided to install it in (on my new lenovo thinkpad) in addition to my windows 7 operating system. Now, whenever I reboot the computer, it only runs window 7. I went (in windows) to Control Pannel ? System ? Advanced Settings ? Startup and Ubuntu is not even listed as a choice for operating system. I tried installing ubuntu again, but now it wants to partition the already partitioned windows folder. I can't figure out how to get Ubuntu, which seems to be installed, to run. I saw on another question here that I could be able to edit my mrb settings using EasyBCD but I can not figure out how to choose ubuntu as an operating system. My disk is already partitioned (seen from the attempted second install) so I'm pretty sure it is on the disk. Basically, how can I get ubuntu to run when I can't choose it as an operating system? Thank you for your help.

  Read the article

• after BIOS splash, will not boot -- asks me to select an OS, but it just reboots

  - by user92040

  I'm running Linux Mint 13 MATE 64-bit. Everything has been working for several weeks. Yesterday, when I tried to boot up my computer, after the BIOS screen flashes I reach a screen with a black background that reads at the top: GNU GRUB version1.99-21ubuntu3.4 Then there is a box in which I can select from the following lines: Linux Mint 13 MATE 64-bit, 3.2.0-31-generic (/dev/sdb2) Linux Mint 13 MATE 64-bit, 3.2.0-31-generic (/dev/sdb2) -- recovery mode Previous Linux versions Memory test (memtest86+) Memory test (memtest86+, serial console 115200) At the bottom it reads: Use the ? and ? keys to select which entry is highlighed. Press enter to boot the selected OS, 'e' to edit the commands before booting or 'c' for a command-line. I have no idea why it started doing this and, worse, I have no idea how to get out of here. No matter which option I select, I can't get it to boot the OS. If I select either of the first two, it reboots to splash the BIOS and then I'm right back where I started. If I choose "Previous Linux versions" I get essentially the same screen with only two choices (which are the same as the first two choices listed above, Linux 13 MATE and the recovery mode). Again, choosing either one of those results in a reboot. If I try to run either of the memtest options, it reads: error: unknown command 'linux16', Press any key to continue... Then it brings me back to the same screen Can anyone help me please? Intel Core i5-2500 ASUS P8Z68-V LX Intel Motherboard G. Skill Ripjaws series F3-12800CL9D-8GBRL (4GB x2) Plextor 128GB M5S Series SSD

  Read the article

• Sysprep.exe completely missing on both of my Windows 7 64bit machines. How should I find a workaround?

  - by Zoltán Tamási

  The sysprep.exe file is simply missing on my Windows 7 64bit machine. I tried to find it on another computer, but it wasn't found there either. I can't understand it, because on a lot of forums and even in the official articles there are a lot of references to this tool. I've checked system, system32, sysWOW64 folders, and even made a full search with Total Commander. I only found a sysprep folder in the system32 folder, but inside was only an en-US subfolder, which was empty. Then I thought I will give my Windows PE bootdisk a try, which I've created a while ago. No result, only the same empty en-US folder is present there as well. Please if anyone knows what's happening, point me to the right direction. I need to clone my system and I'm stuck right at the first step...

  Read the article

• How can I view a .eml file from command line in Windows Vista?

  - by Nosrettap

  Ok, so my parent's computer crashed (horribly - corruptedRegistry) and I'm trying to access one of their e-mail files that is saved locally on the hard drive. I can't launch Windows itself so right now I am in a "bootup command prompt". I've navigated to where the e-mail appear to be stored C:Users\[userName]\AppData\Local\Microsoft\Windows Mail\Local Folders\Inbox and it shows a list of what appear to be the files. The problem is, they are .eml files and I can't seem to be able to open them. I've tried 'vim' and 'vi' commands but it tells me that 'vim is not recognized as an internal or external command. Does anyone know how I can view .eml files from command line? Thanks

  Read the article

• Let a program (called by other program) run as admin without prompt

  - by DarkGhostHunter

  As you may know, Steam doesn't like no-admin accounts for installing games or whatsoever. In my case, I have a user in my computer that usually install a lot of games and every time I have to put my password to successfully play them. Blame, /bin/SteamService.exe. I came up with a solution: using RunAs to make Steam run as the admin user. But that is a potential security risk. So instead of that, I'm asking if is possible to do the following: Hot to run SteamService.exe with high trust levels (or admin privileges) automatically when Steam calls it? That way he can play and install games in Steam leaving the rest of the system alone. I don't mind if the user has to click "yes or no", but without prompt its better because some games asks every time they're executed.

  Read the article

• Can't connect to server from certain machines

  - by Joel Coel

  On a small college campus we have a VLAN setup for the computer labs. These machines get assigned IP addresses in the 192.168.7.xxx range. In the server room, all of the server are on the default VLAN and assigned an IP address in the 10.1.1.xxx range. For the most part this works, but the lab machines are unable to connect to one of the servers. They can't even ping it. They can talk to other servers on the same switch as this server just fine. At first I thought it might be a vlan issue, but I changed the server port vlan to match other known-working ports with no effect. Any ideas?

  Read the article

• Documenting software-updates semi-automatically in MacOS X by parsing log files?

  - by Martin

  I'd like to document changes I made to my computer (running MacOS 10.6.8) to be able to identify the sources of eventual problems. Mostly I install updates when a software notifies me about a newer version and offers me a dialog to download and install the update. Currently I'm documenting those updates "by hand" by noting in a text file, when I have e. g. installed a Flash-Player update or updated another 3rd party software ... I wonder if I could achieve that easier and semi-automatically by parsing system logfiles for certain texts like "install" and that way directly get the relevant information: what has been installed (Software and version) when has been installed where has it been installed/what has changed Is there a way to extract such information by a script from the existing logfiles?

  Read the article

• Redirecting HTTP traffic from a local server on the web

  - by MrJackV

  Here is the situation: I have a webserver (let's call it C1) that is running an apache/php server and it is port forwarded so that I can access it anywhere. However there is another computer within the webserver LAN that has a apache server too (let's call it C2). I cannot change the port forwarding nor I can change the apache server (a.k.a. install custom modules). My question is: is there a way to access C2 within a directory of C1? (e.g. going to www.website.org/random_dir will allow me to browse the root of C2 apache server.) I am trying to change as little as possible of the config/other (e.g. activating modules etc.) Is there a possible solution? Thanks in advance.

  Read the article

• Tile sizes in 2D games

  - by Ephismen

  While developing a small game using tile-mapping method a question came to my mind: I would develop the game on Windows but wouldn't exclude adapting it to another platform. What size(in pixels) would you recommend using for creating the tiles of a tile-mapped game(ie: RPG) with the following requirements? Have an acceptable level of detail without having too many tiles. Having a decent map size. Allow adaptation of the game on a handheld(ie: PSP), smartphone or a computer without too much loss of detail or slowdowns. Allow more or less important zoom-in / zoom-out. Have a resolution of tile that permits either pixel-perfect collision or block-collision. Anything from a good explanation to a game example is useful as long as it can fit the requirements. This question may seem a bit simplistic, but I noticed that many Indies game developer were using inappropriate scales scenery. Also sorry for the poor syntax and the lack of vocabulary of my question, being a non-native English speaker doesn't help when talking about computers programming.

  Read the article

< Previous Page | 558 559 560 561 562 563 564 565 566 567 568 569  | Next Page >