Search Results

Search found 16417 results on 657 pages for 'computer linguist'.

Page 566/657 | < Previous Page | 562 563 564 565 566 567 568 569 570 571 572 573  | Next Page >

• windows 7: Event 55 The file system structure on the disk is corrupt and unusable

  - by Radio

  Here is a real bad one! Windows 7 RTM with SP1 installed [Version 6.1.7601]. Recently tried to delete some folder on my hard drive and Windows prompted "Error 0x80070570: The file or directory is corrupted and unreadable", and at the same time placed an Event 55 describing "The file system structure on the disk is corrupt and unusable. Please run the chkdsk utility on \Device\HarddiskVolume2." Ran chkdsk, first with /f option, then with /r option. Result in both cases was: no errors found, 0 bad sectors. No problems chkdsk found at all! Went through StackExchange, Google and spent over 6 hours on this. Still cannot figure out the problem. Re-installing/Re-Formatting is not an option! What did I try: Hotfix - Windows6.1-KB982927-x64.msu - gave me an error about incompatibility with my computer, however it totally matches my system. CRC of hotfix was ok. Windows Repair Console found startup errors and fixed those, but this didn't help an issue, even by running chkdsk c: /R from it. http://support.microsoft.com/kb/246026 does not promise anything good. sfc /scannow does not help too. Replaced hard drive by cloning an old one using True Image, repeated all steps above. At the same time, some minor glitches started to appear in my Windows, like side panel and notification area settings are getting reset. Goal is to delete the folder and get rid of Event 55. Sounds like NTFS bug. Please help. This is completely ridiculous.

  Read the article

• What do I need to consider when buying hardware to meet my needs?

  - by Darth Android

  I'm looking to build a new computer from the ground up. I'm not sure what to look out for and need guidance and help on how to pick the hardware needed to construct my new rig. How do I know what to buy? How do I find out if a given CPU will be enough for a certain game or application that I want to run? How do I find out if a given graphics card will be enough for a certain game or application? What is important when looking at motherboards? How much memory do I need? How do I know how much wattage I need for a power supply? What size case do I need? What relevant standards do I need to read up on and be aware of? PCI, PCIe, SATA, USB 2.0, USB 3.0, etc... What "gotchas" do I need to be on the lookout for? Please keep responses generation-agnostic to ensure they will be helpful to our future users. While Stack Exchange does not permit shopping recommendations, it doesn't provide any general advice to consider when buying hardware. So, instead of just telling those that ask what to buy that it's not allowed, let's tell them how to figure out what they need. This question was Super User Question of the Week #20 Read the June 20, 2011 blog entry for more details or submit your own Question of the Week.

  Read the article

• Building a PC for Work and play? [closed]

  - by Derek Organ

  Ok, Its been a long time since I build my own PC so I'm looking to get back into it again and build a new one. First off budget is about €800 excluding the monitor and windows 7 licence and mouse. (just bought a new g500) I plan on using my computer for work, lots of applications open at once but none particularly excessive (photoshop being the most demanding, mostly coding tools) I also use it for some gaming, e.g. COD, Starcraft etc. One thing I do want to do eventually is get a really good monitor with hight resolution and maybe 27" so the graphics card needs to be able to make best use of that. So a few questions 1) Is the bottle neck in performance mostly still the harddrives? 2) Aren't most processors e.g. i5 etc even i3 so far a head of other bottlenecks it makes litte difference the higher you go. Isn't the Graphics card dealing with heavy graphics so what really slows because of a slow CPU? So from this my thinking is to get a SSD drive as my primary drive for OS etc and have loads of memory e.g. 6-8GB and a decent mid level graphics card? It doesn't seem at my level worth spending much on CPU and any other parts really. I basic parts off the top of my head Case, Motherboard CPU SSD Drive SATA Drive Power Supply Memory Cooling (fan?) Graphics Card Network Card Keyboard DVD drive Mouse Windows Monitor Am I missing anything? Any helpful tips or general education much appreciated. Thanks, Derek

  Read the article

• Pre-startup segmentation fault with ptrace

  - by sfink

  I have somehow managed to mangle my computer so that any time I attempt to use something that uses ptrace to trace another process (eg strace, gdb), I get an immediate segmentation fault. For example: # strace /bin/true execve("/bin/true", ["/bin/true"], [/* 27 vars */]) = 0 --- SIGSEGV (Segmentation fault) @ 0 (0) --- +++ killed by SIGSEGV +++ or with gdb: # gdb /bin/true GNU gdb Fedora (6.8-27.el5) Copyright (C) 2008 Free Software Foundation, Inc. License GPLv3+: GNU GPL version 3 or later This is free software: you are free to change and redistribute it. There is NO WARRANTY, to the extent permitted by law. Type "show copying" and "show warranty" for details. This GDB was configured as "x86_64-redhat-linux-gnu"... (no debugging symbols found) (gdb) run Starting program: /bin/true Program terminated with signal SIGSEGV, Segmentation fault. The program no longer exists. You can't do that without a process to debug. rpm -V comes up clean on strace, gdb, and glibc. I do not have any LD_* variables set, and PATH has nothing special in it.

  Read the article

• Google Chrome doesn't delete my browsing history correctly

  - by Derfder

  I have deleted everything that I could from my browser history: chrome://settings/clearBrowserData I checked everything and select the begining of time Then when I access browsing history: chrome://history/ There is nothing (as I expected), or to be precise No history entries found. The problem is that I still see my specific search url with very specific query I have made a month ago, when I start typing the url of the website into chrome address bar. How is that possible? Where is Google stroing these data. How to get rid off them completely? I want to mention that my autosuggestion options look like this: So, what else should I delete to remove everything from autosuggestions? Right now it has some specific URLs (subpages, pages with very specific search query I have made in a month or so). I have tried restarting Chrome and restarting my computer, but the urls are still in the autosuggestion. Also I am unable to turn off the autosuggestion, even I have unchecked that option in settings. My Google Chrome version is: Version 27.0.1453.116 m (probably the latest) Btw. in Firefox deleting the history works as expected. So, I guess that this has nothing to do with the operating system I am using (Windows 7), but only it's an issue with Chrome itself.

  Read the article

• Western Digitial My Book: Can't access the data on the drive

  - by Bryan Denny

  My girlfriend has this external hard drive by Western Digital called a My Book. When the external drive is connected, it does not show it as an accessible disk drive on the computer. However, it shows up fine in Device Manager: I can also see it in Disk Management, but the volume is not mapped to a drive letter, nor can I change the drive letter: It only gives me access to Delete Volume: I would rather not lose the data on the drive if possible. What can I do from here to get to the data? Things I've tried/know: Uninstall drivers and re-install them Device does the same thing when attach to either her Win7 laptop or my Win8 laptop I don't think there's an issue with the HDD itself. No clicking noises, etc. I ran Western Digital Data LifeGuard Diangostics (DLGDIAG) and the SMART Status was a "PASS", all of the SMART Disk Information looked fine. I haven't had the time to run the diag tests yet but I do not believe it's a mechanical issue. The hard drive is inside of an enclosure, I have not attempted to pry the drive out yet. How can I get Windows to properly detect this drive?

  Read the article

• Resotre single users Exchange 2003 mailbox from backup

  - by Campo

  I take weekly backups of exchange in full. I also take complete weekly backups of the entire server. It is a Server 2003 R2 with AD and Exchange 2003 all on one box. One users inbox has disappeared. She has 19000+ junk items now. It is possible the inbox got mixed into the junk. Regardless it is such a huge mess she is not going to go through all of that.... I want to restore he mailbox from the backup. I followed this MS KB http://support.microsoft.com/kb/823176 I had to use Method 3. I have a VM of Server 2003 R2 with exchange but I am having failures on the restore from NT backup. The backup log just states to check the application log.... Application log points to backup log... Only info Is failed to restore Only thing different is the computer name... The only error I can find is in the Applicaiton log. Information Store Database not found All others just say that the backup failed. Any assistance is greatly appreciated.

  Read the article

• I have added a port to the public zone in firewalld but still can't access the port

  - by mikemaccana

  I've been using iptables for a long time, but have never used firewalld until recently. I have enabled port 3000 TCP via firewalld with the following command: # firewall-cmd --zone=public --add-port=3000/tcp --permanent However I can't access the server on port 3000. From an external box: telnet 178.62.16.244 3000 Trying 178.62.16.244... telnet: connect to address 178.62.16.244: Connection refused There are no routing issues: I have a separate rule for a port forward from port 80 to port 8000 which works fine externally. My app is definitely listening on the port too: Proto Recv-Q Send-Q Local Address Foreign Address State User Inode PID/Program name tcp 0 0 0.0.0.0:3000 0.0.0.0:* LISTEN 99 36797 18662/node firewall-cmd doesn't seem to show the port either - see how ports is empty. You can see the forward rule I mentioned earlier. # firewall-cmd --list-all public (default, active) interfaces: eth0 sources: services: dhcpv6-client ssh ports: masquerade: no forward-ports: port=80:proto=tcp:toport=8000:toaddr= icmp-blocks: rich rules: However I can see the rule in the XML config file: # cat /etc/firewalld/zones/public.xml <?xml version="1.0" encoding="utf-8"?> <zone> <short>Public</short> <description>For use in public areas. You do not trust the other computers on networks to not harm your computer. Only selected incoming connections are accepted.</description> <service name="dhcpv6-client"/> <service name="ssh"/> <port protocol="tcp" port="3000"/> <forward-port to-port="8000" protocol="tcp" port="80"/> </zone> What else do I need to do to allow access to my app on port 3000? Also: is adding access via a port the correct thing to do? Or should I make a firewalld 'service' for my app instead?

  Read the article

• Is it possible to provide a wired ethernet connection to external devices with an extra LAN card?

  - by Ben McCormack

  I'm trying to provide a wired ethernet connection (wireless is not an option for this device) to a device (Samsung blu-ray player) without running Cat5 cable all over the home. I have a PC sitting next to this device and the PC is connected to the network via a wireless USB adapter. Is it possible to provide a wired connection from the PC to the wired device using the (currently unused) ethernet port in the back of the computer? Here's how I envision the device getting connected to the internet via my network: Linksys WRT54G v8 Wireless Router | ``--> Windows 7 PC connected via wireless | ``--> Blu-ray player connected via wired connection to the ethernet port on the PC. If so, how is this done? Will I need a crossover cable? What settings will I need to change in Windows 7 so that the device can connect? NOTE: I'm trying to avoid having to buy a wireless bridge and/or hacking a router with an open-source firmware to get this to work. See my previous question for more details.

  Read the article

• Bypass proxy authentication [closed]

  - by Diego Queiroz

  My scenario: My network has a proxy that requires interative authentication. When I access any URL, an username and password is requested to enable navigation. I do have a valid username/password (this means I have permissions to access external content). I do not have access to the proxy server (any change to the proxy server is not an option). What I need: I need to bypass the interative authentication process and make it an automated authentication process. What I do NOT need/want: I do not need/want to hack the network. I do not need/want to access unauthorized content. In other words, I just need to find a way to "save" my password in the computer (security is not a problem) to allow application that does not support this kind of interative authentication to access the internet (like non-browser software that also uses HTTP port). My guess: My guess is to develop a new proxy server that will run in the local machine (eg, a proxy for the network proxy). This proxy server will access my network proxy, authenticate and forward the content. Of course this is a last resort. I prefer to not need to develop a proxy server. Does someone know other solution? (any operating system)

  Read the article

• Simple options for port forwarding to a different port?

  - by Nick

  I have three network printers at our local office, all of which listen on port 9100. Non of them offer the option of changing the listening port. We have a single public static IP address, and access to our main network is through a Linksys WRT-54G. We need to be able to print to these printers from outside the office. The problem is, with the 54G, I can only forward a port to the SAME port on a particular IP address. What I really need though is a way to forward to an ip address and a DIFFERENT port. I need to do this: In port Destination 9100 192.168.1.1 : 9100 9101 192.168.1.2 : 9100 9102 192.168.1.3 : 9100 So I'm looking for options. I could setup an old computer with two network cards and IPtables I suppose, but that seems like a lot of overhead for something relatively simple. Is there a way a virtual machine (read: one network card) could do the advanced port forwarding? Where I forward all traffic to it, and it forwards it on to the right printer? Or what about those mini Linux distros that replace the WRT-54G's firmware? Do any of those support what I need "out of the box"? I have a spare WRT- could I make it an IP tables router? Recommendations for mini distros? Or is there an off-the-shelf product that does this (cheap/local preferred)? Any advice / options appreciated. Thanks!

  Read the article

• CPU-adaptive compression

  - by liori

  Hello, Let assume I need to send some data from one computer to another, over a pretty fast network... for example standard 100Mbit connection (~10MB/s). My disk drives are standard HDD, so their speed is somewhere between 30MB/s and 100MB/s. So I guess that compressing the data on the fly could help. But... I don't want to be limited by CPU. If I choose an algorithm that is intensive on CPU, the transfer will actually go slower than without compression. This is difficult with compressors like GZIP and BZIP2 because you usually set the compression strength once for the whole transfer, and my data streams are sometimes easy, sometimes hard to compress--this makes the process suboptimal because sometimes I do not use full CPU, and sometimes the bandwidth is underutilized. Is there a compression program that would adapt to current CPU/bandwidth and hit the sweet spot so that the transfer will be optimal? Ideally for Linux, but I am still curious about all solutions. I'd love to see something compatible with GZIP/BZIP2 decompressors, but this is not necessary. So I'd like to optimize total transfer time, not simply amount of bytes to send. Also I don't need real time decompression... real time compression is enough. The destination host can process the data later in its spare time. I know this doesn't change much (compression is usually much more CPU-intensive than decompression), but if there's a solution that could use this fact, all the better. Each time I am transferring different data, and I really want to make these one-time transfers as quick as possible. So I won't benefit from getting multiple transfers faster due to stronger compression. Thanks,

  Read the article

• Laptop Acer Travelmate 4050 takes over 10 Mins to POST

  - by Belliez

  Hi, I am a computer tech and have received a laptop for repair. I noticed when I turned it on the laptop would not do anything for a min or two (the fan would run up and stop, power led would shine and some cd rom activity then stop). It would sit there with a black screen. Suddenly after a random number of minutes (between 1-20mins!) the Acer BIOS screen would display and POST would happen before booting into Windows XP. It has frozen in XP at various times and pointed towards a CPU fault and over heating. The fan was on its last legs, sounded like a car engine, so I replaced this. Still same issues. I next replaced the CPU like for like. Same problems. Also applied new thermal paste between the cpu and heatsink, when running the fan kicks in occasionally (not as often as I thought it would) and I left it playing mp3, online radio and updating to service pack 3 and it wouldnt freeze. shutting down ok, cold start, not ok. Waits again before showing the BIOS screen. The hard disk was also making a screaming noise (SMART test and chkdsk passed) but I also replaced this. The laptop powers up with and without the battery so dont think its a battery issue. Running out of ideas and wondered if anyone had any advice. Thanks

  Read the article

• How to tell which process is hogging my CPU when they don't add up to 100%?

  - by endolith

  Ubuntu's System Monitor applet shows 100% CPU usage continuously. If I click it, the resources tab shows it at 100% continuously, too. If I go to processes, though, to find out which process is the culprit, there is nothing above 10%. If I run top there is nothing above 10%. The individual processes do not add up to 100%. I try killing lots of processes, but the overall usage continues to be 100%. How can I find out what's hogging the CPU? This is an unusual situation on a computer I use daily, which is never anywhere near 100% CPU unless I'm doing something that requires it (like loading 32 Firefox tabs), after which it goes back to a normal idle level. It's not a new install or anything. There is no reason the processor should be maxed out. I'm not sure when it started or if I changed something that caused it to happen. Normally I would use top or System Monitor and find the process that had gone out of control, but I can't find anything with those tools this time. It persists after reboots and everything. And the processor is obviously hot, so it's not an erroneous reading. Update: I tried killing every process, one at a time, until the problem went away, and killing vino-server finally fixed it, even though that process never went above 5%. I had enabled Remote Desktop a few days ago (and have obviously now disabled it). But the question remains: How did a single process manage to use 100% CPU while top only showed that process at 5%? How do I identify culprits like this in the future? Looks like I'm not the only one who's had this problem: Still a problem in both jaunty & karmic. Interestingly, both System Monitor & htop do not show the sum of individual processes being anywhere near 100% cpu.

  Read the article

• How do I remove a USB drive's write protection?

  - by nate

  I have a SanDisk Cruser Blade USB stick that suddenly seems to be write protected. I tried running DiskPart but after I write the command "attributes disk clear readonly" it displays this: Microsoft DiskPart version 5.1.3565 ADD - Add a mirror to a simple volume. ACTIVE - Marks the current basic partition as an active boot partition. ASSIGN - Assign a drive letter or mount point to the selected volume. BREAK - Break a mirror set. CLEAN - Clear the configuration information, or all information, off the disk. CONVERT - Converts between different disk formats. CREATE - Create a volume or partition. DELETE - Delete an object. DETAIL - Provide details about an object. EXIT - Exit DiskPart EXTEND - Extend a volume. HELP - Prints a list of commands. IMPORT - Imports a disk group. LIST - Prints out a list of objects. INACTIVE - Marks the current basic partition as an inactive partition. ONLINE - Online a disk that is currently marked as offline. REM - Does nothing. Used to comment scripts. REMOVE - Remove a drive letter or mount point assignment. REPAIR - Repair a RAID-5 volume. RESCAN - Rescan the computer looking for disks and volumes. RETAIN - Place a retainer partition under a simple volume. SELECT - Move the focus to an object. It's like when you type help at the DiskPart prompt, so how do I get past this? This problem started when I plugged the stick into a laptop which had viruses, if that's any help.

  Read the article

• SATA Blu-Ray drive not detected via USB adapter

  - by LTR

  I'm using an SATA blu-ray drive (Lite-On IHOS104), connected via a USB adapter to my Windows 7 (32-bit) notebook. The first time I plugged the adapter in, it worked perfectly. The drive appeared in Explorer, and my player software was able to play an encrypted Blu-Ray disc just fine. After the first reboot, it never worked again. Now it shows up as "removable media" with a size of 0 bytes, irregardless of whether a disk is inserted or not. The drive does not show up under the green "eject USB device" icon in the taskbar. The adapter is powered using a separate power adapter. I have tried: disconnecting all other USB devices testing with a DVD instead of a Blu-Ray disc letting Windows search for updated drivers for the drive - there are none using the same drive and adapter on another Win7 (but x64) computer. They work perfectly. using other USB ports on the same notebook - tried them all. using a different SATA/USB-adapter What else can I do to diagnose this problem?

  Read the article

• Epson Artisan 800 on Ubuntu/Linux

  - by Tim Lytle

  Update for Ubuntu 10.04: Printing should work 'out-of-box', scanning still needs the newer sane backend. Looking for a known good way to setup an Epson Artisan 800 on Ubuntu specifically or any linux box in general. It is a printer/scanner with ethernet/wifi/usb. I'd like to use it as a network printer/scanner being able to do both from my Windows and Ubuntu machines; however, if it needs to be physically connected to a computer (preferably the Ubuntu machine) that is doable (again, then sharing print/scan functions to the network). Basically, I'm looking for someone who has used this printer/scanner (or similar) in a multi-platform environment to share how the set it up and how well it worked. Updated: A little more information, like most printers (I expect) the documentation for the printer basically says, "don't use plug-n-play, run our setup CD from your Windows/Mac system", to do anything (set it up for network use even). I guess that's to make it easy for anyone else to setup, but when you're looking to use it with an unsupported (by Epson's documentation) OS, you're just stuck on your own. What I was hoping for was someone who could say, "Forget the bundled software, do [this] to set it up on wifi manually, install [this] to connect to the scanner from [os], printing works with [this] driver - at least that's how I set it up." I'll will (and have so far) use the information here, and post my own setup when I'm done, if there's no one else out there with that experience.

  Read the article

• Valid IP address but can't surf without rebooting

  - by Kat

  I periodically lose internet and router connection at home. When this happens, others are using the router just fine. I am connecting directly through a wired connection to a Belkin router. I can release and renew the IP (and the IP addresses change to 0.0.0.0 and to an IP in my router's range beginning with 192.168.2. as they should) but still can't surf, can't access the router interface. Cycling the router doesn't help, and again, others are able to access the router fine at this time. Only rebooting the computer resolves the issue, and everything is wonderful for a few hours- and then I lose connection again. I have several ideas where to go from here, but I'd like to get some advice first. (Using Windows XP SP3, hardwired connection) Update As stated in the originally, releasing and renewing doesn't solve the issue. However, I have an update. I can ping localhost and my router IP with no problem at all when the issue occurs. However, repairing the network connection does not help. I AM able to get back on by disabling and then re-enabling the network connection in XP. What does that tell us?

  Read the article

• Download JDK onto a remote server

  - by itsadok

  I want to get the latest JDK onto a server in a remote location. Downloading the JDK from Sun's website requires jumping through all kinds of hoops until you actually get the file. I'm not sure exactly if they use cookies or my IP address, but simply copying the file URL and trying wget on the server doesn't work. Googling for mirrors of the JDK, I could only find old versions. Right now I'm left with the option of downloading it into my computer, then uploading it to the server. This feels slow and stupid. Anyone got a better idea? EDIT: Thanks for all the replies. Just to clarify, as I'm writing this I'm rsyncing the 78MB file to my server. It should be done in about an hour, so it's not such a big deal. However, since this is not the first time I'm doing this, I was hoping for a better solution for next time. Solution: What I ended up doing was sudo aptitude install lynx-cur www-browser http://java.sun.com/javase/downloads/ From there it's mostly using the arrow and enter keys, and answering "Yes" to a lot of lynx security questions (about cookies and certificates). Thanks to resonator.

  Read the article

• Getting old bluetooth headset out of standby on Windows 7

  - by luagh45

  I think this is the problem, and if not, I'm open to suggestions. I have an old Jabra BT200 that I used to use on my phone. When a phone call was coming in it would beep using its own noises (meaning the phone never rang inside the headset) and then I could push the 'answer/hang up' button and sound and mic would start working. I have now paired it with Windows 7, and it looks good. Under the playback menu I have 'Bluetooth Hands free Audio / Jabra BT200 (Mono Audio) / Ready', and under the recording menu I have 'Bluetooth Audio Input Device / Jabra BT200 (Mono Audio) / Ready'. However when I try to test the speakers Windows sends a sound, but I never hear it, and when I talk in the mic, Windows never hears me. If I right click either the Bluetooth mic or speakers there's an option to 'Connect', but it's grayed out and I cannot click it. As the final piece of knowledge I have, my headset blinks once every 3 seconds when it's in standby and I can't get that to change. If everything was working it should blink once every second at which point I think all of my problems would be fixed. Hence my issue: I can't seem to get my headset out of standby. On my headset I've tried sending it test noises and then pressing the 'Answer' button, but still nothing. The headset beeps when I press it, so it works, it just doesn't ever come out of standby. Is there maybe some way to trick my headset into thinking it's getting a phone call from my computer?

  Read the article

• Windows 7 restarts while being idle

  - by Ondrej Slinták

  My Windows 7 almost always restarts when I keep it idle for ~20-30mins. It happened randomly before, but lately, if I leave the computer I can be sure it's gonna restart after those 30mins. It never happens when I play games or work tho, just when it's idle. It's a fresh install of Windows 7 64bit. I had also problems while installing it, it always crashed while finalizing the install and I had to reinstall again. Eventually it installed on 3rd or 4th try after I deleted all of my partitions and added them again. I thought it might have been a hardware problem, but temperatures seem to be okay and I have no idea how to track what might have been causing it. Any ideas? I'm running Windows 7 64bit on: Gigabyte EX58-UD4P Intel(R) Core(TM) i7 CPU 920 @ 2.67GHz NVIDIA GeForce GTX 260 6GB of DDR3 1066Mhz RAM WDC WD1001FALS-00J7B0 1TB SATA II I have a very bad feeling it might be something with HDD and its compatibility with Windows 7 as I haven't had those problems for 1 year while I had Vista.

  Read the article

• Macbook Battery Charging Troubles

  - by bobber205

  Problem: Occasionally, my macbook's battery will say it's charging and actually won't be. It stays at 0% for a long time. Other info: I thought it was my battery (laptop was 3 years old). Got a new battery. Issue did not go away. Got a new power supply. Did not go away. Ended up getting a unibody macbook pro. :) (We even ended up moving to a new house). Now still having the issue. The only thing I can think of is my power strip, which is the only thing that has stayed constant. Is it possible for the strip to be affecting the amount of watts my macbook(s) are getting and preventing it from properly charing the battery. I think it goes in and out, the battery picks up the slack and once it's empty the computer shuts down b/c there's no power at all for a second or two. Funny thing is I have a desktop PC on this same strip and it has never had issues with power. Thanks! :)

  Read the article

• Digitize video?

  - by kire

  I got some movies on a VCR that i want to move to my computer somehow. (for personal use) I have a video capture card and all hardware required. I'm looking for the software - programs, codecs etc. I like the format that most torrents come in and got some of these i'd like to use as reference for comparison. How can i see what codec, bitrate, etc a movie is using so i can pick this and know that it will work and look good. For AVI-files the bitrate is visible in explorer but it doesn't mention the codec used and i also have a lot of MKV-files that explorer can't handle. All kinds of tips, tricks and other suggestions are welcome. This is completely new to me. How do I avoid that video/audio gets out of sync for example, many movies you download have audio out of sync so i guess this can happen quite easily. The encoding-program has to run on windows and for playback the movies should work on at least VLC for windows.

  Read the article

• Reducing video mode switching during Linux boot

  - by Zack

  When I boot up my desktop computer, which only has Linux on it, the video mode and/or console font gets switched four times: When GRUB starts, it switches from 80x25 text to a graphical mode so it can draw a pretty background behind its menu; GRUB then goes back to 80x25 text after I pick something from the menu; When the KMS driver for my video card loads, it switches to a much higher-resolution text mode (I don't know if this is a hardware text mode or not); Finally X starts and it goes graphics and stays that way. I think this last switch does not change the resolution of the video mode, only the graphicalness. I'd like to get rid of as many of these mode switches as possible. Ideally, when GRUB takes over from the BIOS it would go directly to the same high-resolution text mode that the KMS driver selects, and the display would stay in that mode till X starts and brings up graphics. I am under the impression that this is possible by mucking with the kernel command line and/or the GRUB console module load parameters, but I don't know the details. GRUB 1.98+20100706, kernel 2.6.32.15 using Nouveau video drivers. Distro is Debian unstable. Please no answers that involve recompiling anything or cobbling together bleeding-edge kernel/driver combinations, I don't care enough about this to go to that much trouble. EDIT: Tobu suggests setting GRUB_GFXMODE to the full pixel resolution of the monitor, and GRUB_GFXPAYLOAD_LINUX=keep to avoid the mode switch after the menu goes away. This does part of what I want, but winds up being worse overall. There's no mode switch after the menu, but there's still a painfully-slow screen repaint (I should probably just give up on GRUB's gfxmode, it's waaaay too slow at 1920x1200). More seriously, there's now a double mode switch when nouveaufb loads, along with fun-looking error messages in dmesg [ 5.923798] [drm] nouveau 0000:02:00.0: allocated 1920x1200 fb: 0x40250000, bo ffff8801ba5f4600 [ 5.923802] fb: conflicting fb hw usage nouveaufb vs EFI VGA - removing generic driver [ 5.923821] [drm] nouveau 0000:02:00.0: PFIFO_INTR 0x00000010 - Ch 1 ("PFIFO_INTR" message repeats 400+ times) [ 5.925609] Console: switching to colour dummy device 80x25 [ 5.925802] Console: switching to colour frame buffer device 240x75

  Read the article

• With no password expire notification at logon in Windows 7, how are you configuring password expire

  - by J. L.

  To my understanding, Windows 7 users do not receive password expiration notification during the logon process - it occurs strictly from the system tray. We currently have tray balloon notifications disabled to lessen user distraction, and I expect the password change process is a smoother one during the logon process rather than in an existing session. As a result, users will get prompted to change their passwords at expiration. The users also connect to Terminal Services boxes, but receive the advanced notification for password expiration there. So, Windows 7 is not notifying, but TS/RDS and XP boxes are. Any guidance on configuring this? Personally, I would turn off all expiration notices, but I understand most users would prefer to see the notification. Thoughts? Any GPO or other settings I might be overlooking? The interactive logon setting below is already enabled for our Win7 workstation GPO. My thought is balloon notifications will get turned back on for Windows 7, but I wanted to see if anyone was aware of alternatives. Thanks. Computer Configuration\Windows Settings\Security Settings\Local Policies - Security Options Interactive logon: Prompt user to change password before expiration

  Read the article

< Previous Page | 562 563 564 565 566 567 568 569 570 571 572 573  | Next Page >