Search Results

Search found 19480 results on 780 pages for 'do your own homework'.

Page 566/780 | < Previous Page | 562 563 564 565 566 567 568 569 570 571 572 573  | Next Page >

• Kernel panic while loading Mac OS X on VMWare

  - by Vladimir Gritsenko

  I have Mac OS X 10.6.3 and VMWare 7.1. Trying to run the OS X doesn't work - shortly after booting VMWare announces the machine's death with this pop-up message: The CPU has been disabled by the guest operating system. You will need to power off or reset the virtual machine at this point. The console has a more interesting announcement: The real-time clock was not properly initialized on your system! With a dump of the detected CPU speed (~2.9 GHz), FSB (~94 MHz) and bus ratio (31). Somehow, the code that panics is documented in an accidental .diff file here. Apparently, it commits seppuku if the bus ratio is greater than 30. I underclocked my E6500 to a slower speed, but this apparently didn't make any difference. I can think of two possibilities right now: The CPU info being read is constant, and defines the maximum ability of the CPU. In which case it appears I'm screwed. VMWare presents its own CPU info to the machine, which I can perhaps somehow change. If so, how? If these sound completely off, that's because I'm a real newbie in these matters. Here's hoping you guys can show me the light :-)

  Read the article

• How to install OS X *.TTC font on Windows? Error: "*.TTC does not appear to be a valid font"

  - by Chris W. Rea

  I own both a Mac running OS X 10.6 Snow Leopard, and a PC running Windows 7. On my Mac is a font called "AmericanTypewriter.ttc". I'd like to use that font on my PC, for a specific creative project. I was able to copy the actual font file over to the PC, but when I try to install it into the Windows Fonts folder I get the following error message: "Cannot install (FONTNAME).ttc - The file '(FONTNAME).ttc' does not appear to be a valid font." Can *.TTC format font files be installed on Windows? If so, how? Thanks! UPDATE: I downloaded the source code for a simple ttc2ttf utility (ttc2ttf_AA.tar.gz) found at this Japanese page and compiled it under cygwin via g++. The resulting executable extracted a single file, "AmericanTypewriter.ttf", from the TTC / True Type Collection. (Why have a collection with only one file!?) However, I still get an error message similar to the one above when I try to install the resulting AmericanTypewriter.ttf onto Windows. I'm stumped again. p.s. I no longer need this font on Windows, but now I'm determined to figure out why & how-to :-)

  Read the article

• Mounting an Azure blob container in a Linux VM Role

  - by djechelon

  I previously asked a question about this topic but now I prefer to rewrite it from scratch because I was very confused back then. I currently have a Linux XS VM Role in Azure. I basically want to create a self-managed and evoluted hosting service using VMs rather than Azure's more-expensive Web Roles. I also want to take advantage of load balancing (between VM Roles) and geo-replication (of Storage Roles), making sure that the "web files" of customers are located in a defined and manageable place. One way I found to "mount" a drive in Linux VM is described here and involves mounting a VHD onto the virtual machine. From what I could learn, the VHD is reliably-stored in a storage role, and is exclusively locked by the VM that uses it. Once the VM Role has its drive I can format the partition to any size I want. I don't want that!! I would like each hosted site to have its own blob directory, then each replicated/load-balanced VM Role to rw mount like in NFS that blob directory to read HTML and script files. The database is obviously courtesy of Microsoft :) My question is Is it possible to actually mount a blob storage into a directory in the Linux FS? Is it possible in Windows Server 2008?

  Read the article

• Updating Windows DNS records from a remote windows DNS server

  - by Luckyboy

  Does anyone know if it is possible for a windows 2003 DNS server to update the records for a domain so that it contains all the records of a domain of of a remotely based DNS server? Im almost certain that doesn't quite explain the problem so I shall illustrate with an example: We have two offices, both are based about 100 miles apart. One deals with IT (Intranet development etc.) while the other is a call centre that uses the Intranet systems. Currently each office has its own DNS server, with the IT office's and call centre's DNS servers containing entries for intranet site. The difference is that the IT DNS server records point to the various servers that host the Intranet sites (e.g. intranetsite1 - 192.168.1.10, intranetsite2 - 192.168.1.11) while all of the entries in the call centre's DNS point to the IT office's DNS server (intranetsite1 - [it office ip address], intranetsite2 - [it office ip address]). Is there any way that the call centre's DNS server could automatically add all DNS records hosted by the IT office's DNS, translating the IP addresses to the IP address of the IT office?

  Read the article

• OSX - User home directories shared via NFS

  - by Hugh

  Hi, I've run into some problems with how I've got user home directories set up on our system here. Our server is an XServe, using Open Directory to manage the user accounts. The majority of our workstations are OSX, but there are a few running Linux (Centos 5.3), and, as time goes on, we expect the proportion of Linux workstations to increase (at some point, we expect to move the server side over to Linux too, but for now we're running with what we've already got) To ensure that the Linux and OSX workstations both see user's home directories in the same place, I shared the home directories using NFS. On the server end, the home directories are stored in: /Volumes/data/company_users This is mounted on the workstations to: /mount/company_users This work fine on the Linux workstations, but there is some weirdness under OSX. For the user who is logged in through the GUI, it all works just fine. However, if a user tries to SSH into a machine that they are not the primary user on, they often have no access to their own home directory. It looks as though OSX is trying to do something else to the user home directories mount point when you log in through the GUI.... For example, on this machine (nv001), I (hugh) am logged into the GUI. Last login: Mon Mar 8 18:17:52 on ttys011 [nv001:~] hugh% ls -al /mount/company_users total 40 drwxrwxrwx 26 hugh wheel 840 27 Jan 19:09 . drwxr-xr-x 6 admin admin 204 19 Dec 18:36 .. drwx------+ 128 hugh staff 4308 27 Feb 23:36 hugh drwx------+ 26 matt staff 840 4 Dec 14:14 matt [nv001:~] hugh% So Matt's home directory is accessible to him. However, if I try to switch to him: [nv001:~] hugh% su - matt Password: su: no directory [nv001:~] hugh% Or: [nv001:~] hugh% su matt Password: tcsh: Permission denied tcsh: Trying to start from "/mount/company_users/matt" tcsh: Trying to start from "/" [nv001:/] matt% Does anyone have any idea why it might be doing this? It's causing me all sorts of problems at the moment... The only machine that I can successfully switch users at the moment is the server that the user directories are stored on, where /mount/company_users is actually just a symlink to /Volumes/data/company_users Thanks

  Read the article

• Linked server problem on SQL Server 2005

  - by BradyKelly

  I have a weird issue and I hope someone can steer me in the right direction for resolving this please. When I execute the following query against a linked server, I get the following error. I can connect to the server in SSMS as a separate server, and execute a similar query against its Deposits table. The nn.nn is my own replacement to avoid broadcasting our server addresses. The query: select td.Batch , td.DateTimeDeposited from Deposits cd left join [172.nn.nn.32\sqlexpress].Terminal.dbo.Deposits td on cd.DateTimeDeposited = td.DateTimeDeposited The error: OLE DB provider "SQLNCLI" for linked server "172.nn.nn.11\sqlexpress" returned message "Login timeout expired". OLE DB provider "SQLNCLI" for linked server "172.nn.nn.11\sqlexpress" returned message "An error has occurred while establishing a connection to the server. When connecting to SQL Server 2005, this failure may be caused by the fact that under the default settings SQL Server does not allow remote connections.". Msg 65535, Level 16, State 1, Line 0 SQL Network Interfaces: Error Locating Server/Instance Specified [xFFFFFFFF]. Notice how the error is about server 172.nn.nn.11 and not 172.nn.nn.32. SOLVED (STUPID ME): Somebody had added an extra bit to my query that was scrolled off-screen and was querying the 17.nn.nn.11 server.

  Read the article

• WebSphere MQ running under local account / group cannot read group memberships for Active Directory user. Workaround or alternative resolution?

  - by noahz

  I am developing an application that is using WebSphere MQ v6.0. WebSphere MQ is currently not working due to the following issue: WebSphere MQ service runs under local user "MUSR_MQADMIN" in the local group "mqm" I attempt to use the service using my own account, BIZ\noahz MUSR_MQADMIN needs to check if BIZ\noahz is in local group "mqm" MUSR_MQADMIN does not have permission to read the Active Directory group membership of BIZ\noahz The following error appears in the MQ log file: ----- amqzfubn.c : 3582 ------------------------------------------------------- 1/31/2011 18:51:32 - Process(704.1105) User(MUSR_MQADMIN) Program(amqzlaa0.exe) AMQ8079: Access was denied when attempting to retrieve group membership information for user 'noahz@biz'. EXPLANATION: WebSphere MQ, running with the authority of user 'musr_mqadmin@noahz-biz', was unable to retrieve group membership information for the specified user. ACTION: Ensure Active Directory access permissions allow user 'musr_mqadmin@noahz-biz' to read group memberships for user 'noahz@biz'. To retrieve group membership information for a domain user, MQ must run with the authority of a domain user. ----- amqzfubn.c : 3582 ------------------------------------------------------- I found more information is here on IBM's web site: http://publib.boulder.ibm.com/infocenter/wmqv7/v7r0/index.jsp?topic=/com.ibm.mq.amqtac.doc/wq10830_.htm I don't have Active Directory admin rights for my Windows machine, so my question is: Is there anything else I can do to resolve (or work-around) this issue and get WebSphere MQ working for me again? For example, can I disable this security check in WebSphere MQ?

  Read the article

• Cisco ASA and SixXS IPv6 tunnel endpoint?

  - by Martijn Heemels

  I recently installed a Cisco ASA 5505 firewall on the edge of our LAN. The setup is simple: Internet <-- ASA <-- LAN I would like provide the hosts in the LAN with IPv6 connectivity by setting up a 6in4 tunnel to SixXS. It would be nice to have the ASA as tunnel endpoint so it can firewall both IPv4 and IPv6 traffic. Unfortunately the ASA apparently can't create a tunnel itself, and can't port-forward protocol 41 traffic, so I believe I would have to do one of the following instead: Set up a host with it's own IP outside the firewall, and have that function as tunnel-endpoint. The ASA can then firewall and route the v6 subnet to the LAN. Set up a host inside the firewall that functions as endpoint, separated via vlan or whatever, and loop the traffic back into the ASA where it can be firewalled and routed. This seems contrived, but would allow me to use a VM instead of a physical machine as endpoint. Any other way? What would you suggest is the optimal way to set this up? P.S. I do have a spare public IP address available if needed, and can spin up another VM in our VMware infrastructure.

  Read the article

• How do I leverage Bitlocker cmdlets?

  - by user1418882

  This article hints at being able to unlock a bitlocked drive using: Unlock-BitLocker -MountPoint -Password However, I know diddly squat about Powershell and how to use the Powershell cmdlets to do what I want to do. So, how do I do use the above to do something like the following? Unlock-BitLocker -MountPoint D:\ -Password "password" Currently about as much as I know how to do is start Powershell and that's it. I don't want to learn masses of Powershell to get to the point where I can do this. All that I need to know in enough to know how I can execute the commands that are pointed out in the first link. So far in the powershell prompt if I past in: Unlock-BitLocker -MountPoint D:\ -Password "password" I get the following error: The term 'Unlock-BitLocker' is not recognized as the name of a cmdlet, function, script file, or operable program. Chec k the spelling of the name, or if a path was included, verify that the path is correct and try again. At line:1 char:17 + Unlock-BitLocker <<<< -MountPoint D:\ -Password "password" + CategoryInfo : ObjectNotFound: (Unlock-BitLocker:String) [], CommandNotFoundException + FullyQualifiedErrorId : CommandNotFoundException This is most likely because I don't have any clue about how the commands on the initially linked page work in a powershell context. This is so that I can answer my own question here: Bitlocker and scheduled task (powershell) script to unlock non-system drive

  Read the article

• Office365 SPF record has too many lookups

  - by Sammitch

  For some utterly ridiculous administrative reasons we've got a split domain with one mailbox on Office365 which requires us to add include:outlook.com to our SPF record. The problem with this is that that rule alone requires nine DNS lookups of the maximum of 10. Seriously, it's horrible. Just look at it: v=spf1 include:spf-a.outlook.com include:spf-b.outlook.com ip4:157.55.9.128/25 include:spfa.bigfish.com include:spfb.bigfish.com include:spfc.bigfish.com include:spf-a.hotmail.com include:_spf-ssg-b.microsoft.com include:_spf-ssg-c.microsoft.com ~all Given that we have our own large-ish mail system we need to have rules for a, mx, include:_spf1.mydomain.com, and include:_spf2.mydomain.com which puts us at 13 DNS lookups which causes PERMERRORs with strict SPF validators, and completely unreliable/unpredictable validation with non-strict/badly implemented validators. Is it possible to somehow eliminate 3 of those include: rules from the bloated outlook.com record, but still cover the servers used by O365? Edit: Commentors have mentioned that we should simply use the shorter spf.protection.outlook.com record. While that is news to me, and it is shorter, it's only one record shorter: spf.protection.outlook.com include:spf-a.outlook.com include:spf-b.outlook.com include:spf-c.outlook.com include:spf.messaging.microsoft.com include:spfa.frontbridge.com include:spfb.frontbridge.com include:spfc.frontbridge.com Edit² I suppose we can technically pare this down to: v=spf1 a mx include:_spf1.mydomain.com include:_spf2.mydomain.com include:spf-a.outlook.com include:spf-b.outlook.com include:spf-c.outlook.com include:spfa.frontbridge.com include:spfb.frontbridge.com include:spfc.frontbridge.com ~all but the potential issues I see with this are: We need to keep abreast of any changes to the parent spf.protection.outlook.com and spf.messaging.microsoft.com records. If anything is changed or [god forbid] added we would have to manually update ours to reflect that. With our actual domain name the record's length is 260 chars, which would require 2 strings for the TXT record, and I honestly don't trust that all of the DNS clients and SPF resolvers out there will properly accept a TXT record longer than 255 bytes.

  Read the article

• map subdomain to another subdomain via cname

  - by Stephen

  Question: I need to get DNS configured to point a subdomain from one domain (which I will generally not be controlling) to another subdomain on a different domain name. Testing this process using a simple CNAME entry keeps pointing to the primary domain and not the subdomain where it should be going. This is the scenario; (newdomain.com is in my control) cdn.xyz.com should display content from this subdomain subdomain.newdomain.com It is instead displaying content from newdomain.com (not the subdomain sub domain) cdn.xyz.com/page.htm displays content from newdomain.com/page.htm although what I need is it to display content from subdomain.newdomain.com/page.htm Other Background: setup is between two different servers with different IP ranges although DNS cluster is on between all servers the newdomain.com is set up with its own unique IP (which is on the A records for the subdomains, the subdomains work as expected/normal) the DNS entry is correct (cdn CNAME subdomain.newdomain.com.) ie the end period is included a DNS lookup on the CNAME externally reports back as subdomain.newdomain.com. as the record Does anyone know what DNS entries I am missing to get this working correctly ? Note: I do not want to just put a redirect between domains as I need the content of subdomain.newdomain.com/content.html to be visible via the URL of cdn.xyz.com/content.html also I can just use some redirects on newdomain.com to achieve what I am after but would prefer to just get the DNS correct. EDIT Current DNS cdn CNAME subdomain.newdomain.com. || CNAME entry for domain1 subdomain A XXX.XXX.XXX.XXX || A record entry for working subdomain pointing to unique IP What should happen is that cdn.domain1.com - subdomain.newdomain.com What is happening is cdn.domain1.com - newdomain.com (ie. the root not the subdomain) EDIT 2 Actually if its easier I am trying to emulate a simple cloud setup like Rackspace Containers (which I assume is similar to Buckets on AWS). although it is not for cloud storage Where a container has a url reference of hd62321678d323.rackspace.com (in truth they are much longer) so I can use a CNAME record of: cdn CNAME hd62321678d323.rackspace.com. so that http://cdn.mydomain.com/myfile.jpg displays content from http://hd62321678d323.rackspace.com/myfile.jpg

  Read the article

• How-To Configure Weblogic, Agile PLM and an F5 LTM

  - by Brian Dunbar

  Agile, Weblogic, and an F5 walk into a bar ... I've got this Agile PLM v 9.3 Running on WebLogic, two managed servers. An F5 BigIP LTM. We're upgrading from Agile v 9.2.1.4 running on OAS. The problem is that while the Windows client works fine the Java client does not. My setup is identical to one outlined in F5's doc: http://www.f5.com/pdf/deployment-guides/bea-bigip45-dg.pdf When I launch the java client it returns this error "Server is not valid or is unavailable." Oracle claims Agile PLM is setup correctly, but won't comment on the specifics of the load balancer. F5 reports the configuration is correct but can't comment on the specifics of the application. I am merely the guy in a vortex of finger-pointing who wants my application to work. It's that or give up on WLS and move back to OAS. Which has it's own problems but at least we know how it works. Any ideas?

  Read the article

• IIS 7.5, Multiple Application Pools, and URL Rewriting (403.18 -- Forbidden)

  - by Jerry Hewett

  Is there any way to configure IIS 7.5 to perform URL rewrites to different application pools on the same site without running into a 403.18 error? We're using Helicon ISAPI Rewrite 3 on IIS 6 and it's working like a charm. The root-level "application" is running under it's own application pool, and on IIS 6 we have no problems doing URL rewrites from that application pool to any one of the other four application pools. But when I copy the same server configuration information over to IIS 7.5 the URL rewrites to any of the other application pools fail with a "403.18 -- Forbidden" error. The weird bit is that the IIS 6 is not (at least as far as I can tell, by looking at the site Service configuration dialog) running under IIS 5 emulation mode, so somehow the rewrites aren't throwing 403.18 errors. So something must be different... but whatever it is, I sure haven't been able to figure it out. Btw, we're not married to Helicon ISAPI Rewrite. If there's another way to preserve our current rewrite configuration rules using another module or method I'd be more than happy to use it.

  Read the article

• Ipsec reload fails to load ipsec.conf Strongswan 5.0

  - by Quentin Swain

  I am having trouble configuring a connection to an Android device using a fedora 17 linux machine and strongSwanv5.0.1dr2. I have made some progress but when I try adding the configuration to support xauth authentication I receive an error when I try to reload the configuration file. I get a similar error for the value ikev1 for the keyexchange setting , and whenever i try to set a value for rightauth. Has anyone else had this problem The man page for ipsec.conf and the documentation on the strongswan wiki both indicated that these settings and values should be fine in 5.0.x.x. I could try setting authby but that is deprecated according to the documentation i read and the xauthpsk value isn't working. Any help is much appreciated thanks. can not load config '/etc/ipsec.conf': /etc/ipsec.conf:25: syntax error, unexpected STRING [leftauth] # /etc/ipsec.conf - Openswan IPsec configuration file # # Manual: ipsec.conf.5 # # Please place your own config files in /etc/ipsec.d/ ending in .conf version 2.0 # conforms to second version of ipsec.conf specification # basic configuration config setup # For Red Hat Enterprise Linux and Fedora, leave protostack=netkey protostack=netkey # Enable this if you see "failed to find any available worker" # nhelpers=0 plutodebug=all conn %default ikelifetime=240m #keylifetime=20m keyingtries=3 ikev2=no conn android left=10.1.12.212 right=10.1.12.140 leftxauthserver=yes leftauth=psk rightauth=xauth keyexchange=ikev1 type=tunnel pfs=no rekey=no auto=start ike=aes256-md5;modp1024 phase2=esp ikev2=no #You may put your configuration (.conf) file in the "/etc/ipsec.d/" #include /etc/ipsec.d/*.conf

  Read the article

• How to configure fastcgi to work with ligttpd in ubuntu

  - by michael

  I am able to run lighttpd on ubuntu 9.10. But when i tried to setup fastcgi with lighttpd by putting this in the ligttpd.conf file: #### fastcgi module fastcgi.server = ( "/fastcgi_scripts/" => (( "host" => "127.0.0.1", "port" => "9098", "check-local" => "disable", "bin-path" => "/usr/local/bin/cgi-fcgi", "docroot" => "/" # remote server may use # it's own docroot )) ) This is what I get in the error.log in ligttpd: 2010-03-07 21:00:11: (log.c.166) server started 2010-03-07 21:00:11: (mod_fastcgi.c.1104) the fastcgi-backend /usr/local/bin/cgi-fcgi failed to start: 2010-03-07 21:00:11: (mod_fastcgi.c.1108) child exited with status 1 /usr/local/bin/cgi-fcgi 2010-03-07 21:00:11: (mod_fastcgi.c.1111) If you're trying to run your app as a FastCGI backend, make sure you're using the FastCGI-enabled version. If this is PHP on Gentoo, add 'fastcgi' to the USE flags. 2010-03-07 21:00:11: (mod_fastcgi.c.1399) [ERROR]: spawning fcgi failed. 2010-03-07 21:00:11: (server.c.931) Configuration of plugins failed. Going down. I do have cgi-fcgi in /usr/local/bin: $ which cgi-fcgi /usr/local/bin/cgi-fcgi Thank you for your help.

  Read the article

• LDAP authentication issue with Kerio Connect

  - by djk

  We have Kerio Connect (mail server) running on a Windows Server 2003 server on a domain. In the webmail client, users are able to change their domain password. This functionality used to work fine until a user tried to change their password a few days ago, when every password they'd try would result in the webmail client claiming their password was "invalid". I spoke to Kerio about this and they claim that this error is returned by the domain controller, which supports my initial investigations. The error that the DC is logging when an attempt is made to change the password is this: "80090308: LdapErr: DSID-0C090334, comment: AcceptSecurityContext error, data 52e, vece" The "data 52e" part indicates that this is an "invalid credentials" error. I don't see how this can be as I've tried (in the Kerio Connect configuration) various accounts that have privileges to modify accounts, including my own as I am a domain admin. I have ran 'dcdiag' (all tests) on the DC and it came back passing every single one of them. I've searched high and low for an answer to this and came up empty. Does anyone have any idea why this may have suddenly started happening? Thanks! Edit: I should mention that the passwords we are changing to do comply with the complexity policy.

  Read the article

• IIS 7.5, Multiple Application Pools, and URL Rewriting (403.18 -- Forbidden)

  - by Jerry Hewett

  Is there any way to configure IIS 7.5 to perform URL rewrites to different application pools on the same site without running into a 403.18 error? We're using Helicon ISAPI Rewrite 3 on IIS 6 and it's working like a charm. The root-level "application" is running under it's own application pool, and on IIS 6 we have no problems doing URL rewrites from that application pool to any one of the other four application pools. But when I copy the same server configuration information over to IIS 7.5 the URL rewrites to any of the other application pools fail with a "403.18 -- Forbidden" error. The weird bit is that the IIS 6 is not (at least as far as I can tell, by looking at the site Service configuration dialog) running under IIS 5 emulation mode, so somehow the rewrites aren't throwing 403.18 errors. So something must be different... but whatever it is, I sure haven't been able to figure it out. Btw, we're not married to Helicon ISAPI Rewrite. If there's another way to preserve our current rewrite configuration rules using another module or method I'd be more than happy to use it.

  Read the article

• OpenLDAP mirror mode replication failing with TLS behind a load balancer

  - by Lynn Owens

  I have two OpenLDAP servers that are both running TLS. They are: ldap1.mydomain.com ldap2.mydomain.com I also have a load balancer cluster with a dns name of it's own: ldap.mydomain.com The SSL certificate has a CN of ldap.mydomain.com, with SANs of ldap1.mydomain.com and ldap2.mydomain.com. Everything works... Except mirror mode replication. My mirror mode replication is setup like this: ldap.conf TLS_REQCERT allow cn=config.ldif olcServerID: 1 ldap://ldap1.mydomain.com olcServerID: 2 ldap://ldap2.mydomain.com On ldap1, olcDatabase{1}hdb.ldif olcMirrorMode: TRUE olcSyncrepl: {0}rid=001 provider=ldap://ldap2.mydomain.com bindmethod=simple bindmethod=simple binddn="cn=me,dc=mydomain,dc=com" credentials="REDACTED" starttls=yes searchbase="dc=mydomain,dc=com" schemachecking=on type=refreshAndPersist retry="60 +" On ldap2, olcDatabase{1}hdb.ldif olcMirrorMode: TRUE olcSyncrepl: {0}rid=001 provider=ldap://ldap1.mydomain.com bindmethod=simple bindmethod=simple binddn="cn=me,dc=mydomain,dc=com" credentials="REDACTED" starttls=yes searchbase="dc=mydomain,dc=com" schemachecking=on type=refreshAndPersist retry="60 +" Here's the errors I'm getting in syslog: Dec 1 21:05:01 ldap1 slapd[6800]: slap_client_connect: URI=ldap://ldap2.mydomain.com DN="cn=me,dc=mydomain,dc=com" ldap_sasl_bind_s failed (-1) Dec 1 21:05:01 ldap1 slapd[6800]: do_syncrepl: rid=001 rc -1 retrying Dec 1 21:05:08 ldap1 slapd[6800]: conn=1111 fd=20 ACCEPT from IP=ldap.mydomain.com:2295 (IP=ldap1.mydomain.com:636) Dec 1 21:05:08 ldap1 slapd[6800]: conn=1111 fd=20 closed (TLS negotiation failure) Any ideas? I've been working on OpenLdap for way too long now.

  Read the article

• Windows 7 wont boot from any boot loader except for 'Windows Boot Manager' after partition resize

  - by user2468327

  I have a triple boot system on a single SSD. OSX, Windows 7, and Ubuntu. I use Chimera (basically another version of Chameleon) as my boot loader. Usually I can boot all 3 without any issue, but after using GParted to make my Ubuntu partition 2 Gigs larger, Windows 7 throws me an error when trying to boot to it from either Chimera or Grub. The error is consistently: 0xc000000e "cant find \Boot\BCD" (slightly paraphrased). However, I can still get into Windows by selecting "Windows Boot Manager" from the boot options in my bios. I've already tried several known fixes for similar issues, including bootrec /rebuildbcd (and variations), and BootRec.exe/fixMBR + BootRec.exe/fixBoot. Ive also tried Chkdsk. At best this has made it so Windows 7 boots on it's own by default (making me have to reinstall Chimera and change back my boot settings in the bios). At worst this made it so Windows wont boot period. Now I'm back full circle where I started. A detail that might be useful is that bootrec /rebuildbcd says that the number of found Windows installations is 0. How do I get it back so I can boot Win7 through another boot loader so I don't have to manually select it in the bios? Preferably without a reinstall.

  Read the article

• Using %v in Apache LogFormat definition matches ServerName instead of specific vhost requested

  - by Graeme Donaldson

  We have an application which uses a DNS wildcard, i.e. *.app.example.com. We're using Apache 2.2 on Ubuntu Hardy. The relevant parts of the Apache config are as follows. In /etc/apache2/httpd.conf: LogFormat "%v %h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" vlog In /etc/apache2/sites-enabled/app.example.com: ServerName app.example.com ServerAlias *.app.example.com ... CustomLog "|/usr/sbin/vlogger -s access.log /var/log/apache2/vlogger" vlog Clients access this application using their own URL, e.g. company1.app.example.com, company2.app.example.com, etc. Previously, the %v in the LogFormat directive would match the hostname of the client request, and we'd get several subdirectories under /var/log/apache2/vlogger corresponding to the various client URLs in use. Now, %v appears to be matching the ServerName value, so we only get one log under /var/log/apache2/vlogger/app.example.com. This breaks our logfile analysis because the log file has no indication of which client the log relates to. I can fix this easily by changing the LogFormat to this: LogFormat "%{Host}i %h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" vlog This will use the HTTP Host: header to tell vlogger which subdirectory to create the logs in and everything will be fine. The only concern I have is that this has worked in the past and I can't find any indication that this has changed recently. Is anyone else using a similar config, i.e. wildcard + vlogger and using %v? Is it working fine?

  Read the article

• Replacing DropBox with: Amazon S3 + SSL + GPG/TrueCrypt + Mounting on OSX ??

  - by Matt Rogish

  So, right now we're using DropBox to share various data files around between approximately 10 Mac OS X systems. However, we already have an S3 account and everyone on the lowest DropBox plan of $10/mo seems too expensive. We'd like to avoid any kind of local storage (share a disk on a desktop or something) since we're a geographically distributed team). So, I am contemplating something that would allow us to replace DropBox with our own home-grown solution. We are all fairly technical people and/or smart enough to follow some steps, so if it's not as "user friendly" as DropBox we're all comfortable with that. There are plenty of docs out there that have bits and pieces of what I want but some of the tools don't seem to fit the requirements: Transport security via SSL to the bucket Encryption of bucket contents Bi-directional syncing Most of the scripts I can find on the internet use "duplicity" which appears to fail #1 (it doesn't look like duplicity supports SSL to S3 - the docs don't state but the protocol looks plain old http http://www.nongnu.org/duplicity/duplicity.1.html#sect6 ) Many scripts use gpg to encrypt files. This seems like it could work, however I have to make sure that each OSX client is able to use the same key to encrypt and decrypt files (key management is left to me to manage). FTP and other client-based apps don't seem to support this at all. Finally, most of the scripts use one-way replication, e.g. using Amazon S3 as a simple backup store. As we'd be using Amazon S3 as the "repository" they fail this one. Whew. So, I'd love a single tool that does this but after an exhaustive search I don't think one exists. In my mind, the magical tool would be some combination of TrueCrypt and rsync. I'd be happy just knowing which tools out there can fulfill my 3 requirements, after that I can stitch together the rest. Any thoughts? THANKS!

  Read the article

• Basic 301 Redirection Help

  - by Marc

  I am trying to learn redirection for a WordPress site of my own. I am testing the concept of redirecting a single WordPress post by using a dummy site. However, it doesn't seem to be working for me. I am trying to redirect www.perfectmatchmaker[dot]org/finding-the-right-matchmaker to www.perfectmatchmaker[dot]org/finding-the-perfect-matchmaker I read that using the following is how to do this: Redirect 301 /old.html http://www.you[dot]com/new.html So this is what my .htaccess file currently looks like: # Use PHP5 as default AddHandler application/x-httpd-php5 .php # BEGIN WordPress <IfModule mod_rewrite.c> RewriteEngine On RewriteBase / RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule . /index.php [L] </IfModule> # END WordPress Redirect 301 /finding-the-right-matchmaker.html http://www.perfectmatchmaker.org/finding-the-perfect-matchmaker.html I've also tried removing the ".html". The redirection of the URL is finally working, but the URL shows no posts available. If I try to redirect the other post on the site by adding the following on the next line of the .htaccess file, I get an error that there is a "redirect loop" occurring. redirect 301 /find-love-and-your-perfect-match-through-the-use-of-a-match-maker http://www.perfectmatchmaker.org/find-love-and-your-perfect-match Any help you can provide me would be much appreciated. Thanks! Marc

  Read the article

• PostgreSQL lots of writes

  - by strife911

  Hi, I am using postgreSQL for a scientific application (unsupervised clustering). The python program is multi-threaded so that each thread manages its own postmaster process (one per core). Hence, their is a lot of concurrency. Each thread-process loop infinitely though two SQL queries. The first is for reading, the second is for writing. The read operation considers 500 time the amount of rows the write operation considers. Here is the output of dstat: ----total-cpu-usage---- ------memory-usage----- -dsk/total- --paging-- --io/total- usr sys idl wai hiq siq| used buff cach free| read writ| in out | read writ 4 0 32 64 0 0|3599M 63M 57G 1893M|1524k 16M| 0 0 | 98 2046 1 0 35 64 0 0|3599M 63M 57G 1892M|1204k 17M| 0 0 | 68 2062 2 0 32 66 0 0|3599M 63M 57G 1890M|1132k 17M| 0 0 | 62 2033 2 1 32 65 0 0|3599M 63M 57G 1904M|1236k 18M| 0 0 | 80 1994 2 0 31 67 0 0|3599M 63M 57G 1903M|1312k 16M| 0 0 | 70 1900 2 0 37 60 0 0|3599M 63M 57G 1899M|1116k 15M| 0 0 | 71 1594 2 1 37 60 0 0|3599M 63M 57G 1898M| 448k 17M| 0 0 | 39 2001 2 0 25 72 0 0|3599M 63M 57G 1896M|1192k 17M| 0 0 | 78 1946 1 0 40 58 0 0|3599M 63M 57G 1895M| 432k 15M| 0 0 | 38 1937 I am pretty sure I could write more often than that for I have seen it write up to 110-140M on dstat. How can I optimize this process?

  Read the article

• Screen scraping software that will traverse pages

  - by nilbus

  We're creating a mashup site that pulls information from many sources all over the web. Many of these sites don't provide RSS feeds or APIs to access the information they provide. This leaves us with screen scraping as our method for collecting the data. There are many scripting tools out there written in different scripting languages for screen scraping that require you to write scraping scripts in the language the scraper was written in. Scrapy, scrAPI, and scrubyt are a few written in Ruby and Python. There are other web-based tools I've seen like Dapper that create XML or RSS feeds based on a webpage. It has a beautiful web-based interface that requires no scripting skills to use. This would be a great tool, if it were able to traverse multiple pages to gather data from hundreds pages of results. We need something that will scrape information from paginated web sites, much like scrubyt, but with a user interface that a non-programmer could use. We'll script up our own solution if we need to, probably using scrubyt, but if there's a better solution out there, we want to use it. Does anything like this exist?

  Read the article

• Can I subnet a subnet?

  - by Portman

  Apologies in advance for the botched terminology. I have read the Server Fault Subnet Wiki but this is more of an ISP question. I currently have a /27 block of public IPs. I use give my router the first address in this pool and then use 1-to-1 NAT for all the servers behind the firewall, so that they each get their own public IP. The router/firewall is currently using (actual addresses removed to protect the guilty): IP Address: XXX.XXX.XXX.164 Subnet mask: 255.255.255.224 Gateway: XXX.XXX.XXX.161 What I would like to do is break out my subnet into two separate /28 subnets. And do this in a way that is transparent to the ISP (i.e., they see me as continuing to operate a single /27). Currently, my topology looks like: ISP | [Router/Firewall] | [Managed Ethernet Switch] / \ \ [Server1] [Server2] [Server3] (etc) Instead, I would like it to look like: ISP | [Switch] / \ [Router1] [Router2] | | | | [S1] [S2] [S3] [S4] (etc) As you can see, this would partition me into two separate networks. I'm struggling with what the correct IP settings would be on Router1 and Router2. Here's what I have right now: Router1 Router2 IP Address: XXX.XXX.XXX.164 XXX.XXX.XXX.180 Subnet mask: 255.255.255.240 255.255.255.240 Gateway: XXX.XXX.XXX.161 XXX.XXX.XXX.161 Note that normally you would expect Router2 to have a gateway of .177, but I'm trying to get them both to use the gateway originally given to me by the ISP. Is subnetting like this in fact possible, or am I completely botching the most basic concepts?

  Read the article

< Previous Page | 562 563 564 565 566 567 568 569 570 571 572 573  | Next Page >