Search Results

Search found 94919 results on 3797 pages for 'new folder'.

Page 566/3797 | < Previous Page | 562 563 564 565 566 567 568 569 570 571 572 573  | Next Page >

  • Mail server hammering

    - by Rodrigo
    I've noticed a quick increase on smtp connections coming to my server, investigating it further i figured out that there's a botnet hammering my smtp server. I've tried to stop it by adding a rule at iptables: -N SMTP-BLOCK -A SMTP-BLOCK -m limit --limit 1/m --limit-burst 3 -j LOG --log-level notice --log-prefix "iptables SMTP-BLOCK " -A SMTP-BLOCK -m recent --name SMTPBLOCK --set -j DROP -A INPUT -p tcp --dport 25 -m state --state NEW -m recent --name SMTPBLOCK --rcheck --seconds 360 -j SMTP-BLOCK -A INPUT -p tcp --dport 25 -m state --state NEW -m recent --name SMTP --set -A INPUT -p tcp --dport 25 -m state --state NEW -m recent --name SMTP --rcheck --seconds 60 --hitcount 3 -j SMTP-BLOCK -A INPUT -p tcp --dport 25 -m state --state NEW -j ACCEPT That would avoid them from hammering "too fast", however the problem still, there's like 5 tries per second, it's going insane, i had to incrase the maximum number of childs of sendmail/dovecot. There's too many ips to filter out manually and simply changing the smtp to another port is not practical since i got many other clients on that server. I'm using sendmail with dovecot, any ideas to have this filtered out more efficiently?

    Read the article

  • Basic Exchange Deployment Question

    - by charnley
    I have come into a situation where I need to deploy a new Exchange server at a small company. I haven't dealt with the newest version of Exchange (2010) yet, but am familiar with 2003 and 2007. The site is currently running one Exchange 2003 server, which hosts about 100 mailboxes. We have new hardware for an additional server, and this is where I need some advice. Should I install Exchange 2010 on the new hardware and leave the older server as-is? Do I upgrade the old server and use it as a bridgehead or replication partner (there is nothing wrong with it other than it is a few years old and running Win2003/Exchange2003)? Can I leave the older 2003 server alone with only the POP mailboxes on it, and will it peacefully co-exist with the new server? Any advice is very appreciated!

    Read the article

  • CIFS mounted drive setting "stick-bit" on all files, cannot change permissions or modify files

    - by mattmcmanus
    I have a folder mounted on an Ubuntu 8.10 sever through cifs that I simply cannot change the permissions on once mounted. Here is a breakdown of what's going on: All files within the mounted folder automatically have their permissions set to -rwxrwSrwx regardless of whether the file is create on the windows server or on the linux machine. I have the same directory mounted on two other linux servers (both running 9.10 instead of 8.10) with no problems at all. They all are using the same fstab options and the same credentials. //server/folder /media/backups cifs credentials=/etc/samba/.arcadia_cred,noexec,noserverino 0 0 I've I run a chmod command a million different ways, all of which report successfully changing the permissions. However it doesn't. The issue began after I updated from 8.04 to 8.10 Any idea why this may be happening on one machine? Since it started after an upgrade I'm not sure what is the bes thing to do. Any help you could give would great! None of my automated backup scripts are working because of this!

    Read the article

  • Amazon EBS for web site files

    - by MattB
    I'm new to the Amazon EC2/EBS system. I'm trying to figure out the "best practice" for hosting a web application (php, ASP.NET, etc.). The way I see it, I have 2 options: Have the instance hold my web files - Don't need to worry about attaching volume's etc.? Have EBS volume hold my web files - Easily update with new code without needing to recreate the AMI for new updates? How do others handle this?

    Read the article

  • Mount an additional Xserve volume with autofs on Linux

    - by daustin777
    A few years ago I setup autofs on a RH Linux box to mount volumes from four XServes. I need to add a couple new volumes from these same Xserves so that I can access files from the Linux box. I've completely forgotten how to do this and haven't been able to find a solution online. How do I add the new volumes? Do I need to add paths to the new volumes?

    Read the article

  • Unable to see a newly added virtual disk in Virtualbox

    - by uswaretech
    I am using virtualbox with Host: Ubuntu 9.10 Guest Win 7 My old virtual disk was filing up so I added a new virtual disk. After I restarted the guest, I can not see it in the My computer. I can see a new disk in the device manager though. The new disk was added as primary slave. What do I need to do to see it? I am guess I need to format the new virtual disk, but since I dont see any drive letter mapped to it, I am not sure of how to do this.

    Read the article

  • How to set JS source directory in apache2?

    - by highBandWidth
    I am trying to run a very basic webserver for development/debugging. The static HTML seems to be delivered correctly, but it seems that the JavaScript libraries are not being delivered to the browser. The page HTML says something like <html> <head> <script type='text/javascript' src="/lib/json.js"></script> ... Now, I have set up a link for /lib/ in my httpd.conf as: Scriptalias /lib/ "/SomeFolder/lib/" When I do this, it can't fetch the files because this is what I see in my apache error log: ... [error] [client ::1] client denied by server configuration: /SomeFolder/lib/json.js, referer: http://localhost/SomeSite It seems that apache is not allowing access to the folder, so I add this to httpd.conf: Directory "/SomeFolder/lib/"> Allow from all </Directory> After this, browsing the page still does not run the JS, instead I see the following error in my apache error log: [error] [client ::1] (13)Permission denied: exec of '/SomeFolder/lib/json.js' failed, referer: http://localhost/SomeSite So now, it seems that apache is trying to run the JS files on the server like a cgi script or something. But I have not made that folder a cgi-bin folder. The only lines where SomeFolder is mentioned by name is in these lines in httpd.conf: Scriptalias /lib/ "/SomeFolder/lib/" Directory "/SomeFolder/lib/"> Allow from all </Directory>

    Read the article

  • OS X, Chrome, and Spaces annoyance

    - by David Hollman
    Here's my problem: I use Google Chrome as my web browser on MacOS X Snow Leopard. I am a keyboard shortcut addict, and I use QuickSilver to create keyboard shortcuts for anything I can. One of the most common things that I do is to open a new web browser window. But I use Spaces frequently to partition my tasks that I am currently working on, and when I open a web browser or web page with a QuickSilver trigger, spaces switches to the last space that I used Chrome on and opens a new tab, which often distracts me for hours because it brings me to a different space and thus a different task. I can fix this by right-clicking on the Google Chrome icon and clicking the "New Window" option, which opens a new window on the current space. I have tried to compose an AppleScript to do something like this, with no success. It has become a serious problem. Back when I used Firefox, I solved the problem by changing a preference item that says "Always open pop-up links in a new window" or something like that, which was kind of a sledge hammer approach, but it worked. I can always go back to Firefox, but I thought I'd ask my question here first. Anyone with any ideas?

    Read the article

  • Recover an HP recovery partition from an offline drive

    - by eric.chartier
    I have a (semi)-dead hard drive with an HP recovery partition on it. My goal is to 1-Buy a new hard drive (checked) 2-Copy the recovery partition to a drive ( dd if=/dev/sdb1 of=~/recovery.bak ) 3-Make a new partition of 12000 mb with Windows 7 4-Copy back recovery partition to the new drive ( dd if=~/recovery.bak of=/dev/sdb1 ) Then press F11 when the laptop boots however it does NOT work. Any idea why? It seemed quite fool proof...

    Read the article

  • using svnadmin in a php script

    - by fabjoa
    Howdie Scenario: Allow developers to submit new application packages to a market server. Developers run a bash script which contains a cURL call to market server (localhost/market/submit/$app-name). The submit script on the server creates a new folder in existing svn server with the name of the submitted app. Script on dev side waits for HTTP to issue a success message and then do a svn checkout in dev local machine. Problem: The submit script on the market server failed to create new svn directory through code: echo `svnadmin mkdir -m 'added new package $package' http://localhost/market/packages/$package`; this does not echo nothing and when I go on http://localhost/market/packages, the folder has not been added and the revision number has not been incremented. I've tried from a terminal in market server chown root:www-data /usr/bin/svnadmin but still no luck. Somebody has come acrosss similar problem? Any solutions? Thanks! Profile: Linux/Ubuntu, apache subversion

    Read the article

  • download management

    - by Jonathan
    I download many files, usually 2 or 3 a day, often 10ish. Some of them are duplicates because I just can't be bothered to find the original in my downloads folder. I have previously tried DAP and used that to create a new subfolder for each day's download. yet I have found this insufficient as sometimes I wish to find files by name/file type or I have multiple parts of downloads over more than one day. Another problem I have found is zips/rars/etc after downloading them and extracting them I then have the zip and the folder. I like it like on a Mac where it automatically extracts the zip after it has been downloaded and removes the zip. What I'd like to be able to do is sort the downloads by date, but dynamically so they are just in the big downloads folder, but I can just press a button and it will show me all the files from a particular site, or from a particular day or by a certain file type. Is there any software that will do this? I use Chrome as a browser but also have Firefox and like that. Jonathan

    Read the article

  • Windows XP error message: "Windows cannot find 'explorer.exe'"

    - by Meysam
    In Windows XP I can open "My Computer" and see all the hard drives. I can also see the explorer.exe process running among other processes in Task Manager. But after opening "My Computer", when I double click on one of the drives to open it, I get the following error message: Windows cannot find 'explorer.exe'. Make sure you typed the name correctly, and then try again. To search for a file, click the start button, and then click search. Although I could detect and remove several suspicious files using Malwarebytes & Microsoft Security Essentials, the problem still remains. The interesting point is that if I right click on one folder and select Open or Explore from the menu bar, I can open the folder! but if I double click on the folder, it does not open and I get the above error message. How can I fix this problem? Any advice would be appreciated! Update: I formatted the C: drive (NTFS), a deep format, and installed a fresh Windows XP on it. I am not getting this error when I double click on C drive icon anymore. But the same error appears when I double click on other drive names. Maybe I should format them too!

    Read the article

  • Upgrade MS Sql Report Server 08 for Dundas charts

    - by hadi
    Hi, We have ms sql server 2008, however the new dundas charts are not available on the report server. How do I upgrade the report server so it gets the new dundas charts as well. Dundas charts are a part of Microsoft charts now in the new version of the report server. Your help would be greatly appreciated

    Read the article

  • Cannot access drive in Windows 7 after scandisk lockup, but can in safe mode....

    - by Matt Thompson
    I ran scandisk on my external USB drive due to the inability to delete a few files. Windows asked me if I wanted to unmount the drive before the scan, warning me that it would be unusable until the scan was finished, and I said yes. During the scan, my machine locked up, and I was forced to reboot the machine. When it came up, I was unable to access the drive, getting an error that "L:is not accessible, access is denied". Comupter Management sees the drive, and has the proper amount of disk space filled. I booted into safe mode, and can access the drive with no problems, and I noticed that in explorer, all the folders have locks on them. I booted back into windows, but still could not access the drive, getting the same error as above. Hovever, if I right click on the drive, select properties, and go to Customize, in the folder pictures ares, I select Choose File, and a window open up, that shows the root of the directory, with all the folder able to be accessed, but again, the icon is the folder icon with a lock on it. I can even copy files from the drive to another. So, the files are not gone, windows can obviously access the drive no matter what it thinks, so there has to be a problem with the flag windows put on the drive when it ran the original scan that failed. I was able to run a scan both in safe mode with no problems, and in windows. In windows, I received the cannot access error the first time I run scan disk on it, but if I try again, it works fine. Any ideas on how to clear the flag that windows set, so I can access the drive normally again?

    Read the article

  • TrueCrypt & upgrading your hard drive?

    - by Danielb
    I currently use TrueCrypt to encrypt the hard drive in a Win7 laptop (everything in a single partition). I am looking to upgrade the hard drive to a model with significantly more storage capacity. I've had a look through the documentation but I couldn't see anything about this particular scenario. I assume I need to do something like the following: Remove the encryption from the existing drive. Clone the existing drive image onto the new hard drive. Physically install the new drive into the laptop. Resize the single partition to use all the space in the new drive. Encrypt all of the new bigger drive with TrueCrypt.

    Read the article

  • Email forwarding via spf record

    - by Y.G.J
    I have old-domain.co.il with several emails and a new-domain.co.il with the same email addresses. I don't want to connect my domain to a server via mx to make that transfer via email server. Is it possible to have a SPF record that get an email like [email protected] and transfer it to [email protected]? The new domain is on google apps and the old domain can be connected to the same apps, but how to do it, so emails will arrive only to the new one?

    Read the article

  • Using GUI ftp on Win7 and Vista without additional software

    - by Stephen Jones
    Goal: provide a 'no-software' method for 'less technical' users to access password protect ftp location from Win7 and Vista (existing approach for WinXP works). 'No software' method to mean without installing additional software (e.g. FileZilla, WinSCP) - the solution is supplied to external non-technical users. WinXP (works): Using Windows Explorer, WinXP supports non-technical ftp access by pasting: ftp://username:[email protected] into the address bar. The remote ftp site's files / directory structure becomes available and can be copied to / from easily (in the style of local file copy / paste) by a 'less technical' user. Win7 / Vista (doesn't work): Pasting the same URL into the Windows Explorer on Win7 or Vista causes an error: An error occurred opening that folder on the FTP server. Make sure you have permission to access that folder. Details: The connection with the server was reset. Notes: a) The same username/password/server typed from the (DOS) command line achieves access to the server, but this is a more 'technical' solution than desired. I am looking for a WinXP equivalent solution. b) Under 'Control Panel' / 'Internet options' / 'Advanced' tab - the boxes for 'Enable FTP folder view' and 'Use Passive FTP' are ticked (enabled) c) Adding an inbound firewall rule for local port 20 (TCP) was attempted with no difference in results (i.e. failure)

    Read the article

  • Enable FTP on OS X 10.8 Mountain Lion Server

    - by Oleg Trakhman
    There is a LAN comprising several mac machines (iMac, Mac Pro, macbook etc.), Airport Express router and Mac Mini Server running OS X Server 10.8 (Mountain Lion Server). I need to share a folder on Mac Mini Server by FTP. What did I try so far: Made special partition for FTP Access, call it "Reports" So shared folder would be "/Volumes/Reports" Gave access every user and group in system, and also enabled guest access. I checked posix acl, which is "rwxrwxrwx", I checked sharing settings in "Preferences.app" and "Server.app" Checked that users have access to FTP service Enabled FTP in Server.app I tried access to shared folder (by FTP): via Cyberduck via Finder via shell: ftp server.local And what I got: $ ftp [email protected] Trying 10.0.2.2... Connected to server.local. 220 10.0.2.2 FTP server (tnftpd 20100324+GSSAPI) ready. 331 User ftpuser accepted, provide password. Password: 530 User ftpuser may not use FTP. and $ ftp [email protected] Trying 10.0.2.2... Connected to server.local. 220 10.0.2.2 FTP server (tnftpd 20100324+GSSAPI) ready. 331 User admin accepted, provide password. Password: 530 User admin denied by SACL. ftp: Login failed ftp> (admin is administrator account , ftpuser is special user account made to access ftp) What I'm doing wrong? Getting really tired of this...

    Read the article

  • Why maximum 1.0 Gbit Ethernet connection an old notebook, and only 100 Mbit on newer faster computer

    - by Sam
    Strange problem about Ethernet speed: recently we bought an i7 core computer running Win7 64 bit with an onboard Gigabit Ethernet controller (Realtek PCIe Gbit Ethernet Family controller). Connecting this new fast pc directly to our brand new ASUS Gigabit Ethernet router via CAT6 cable(!) shows up the adapter status (see picture attached) only 100mbit, while the router is capable of 1000 mbit. More facts: Connecting an 8 year old IBM notebook with gigabit ethernet to the same cable end shows 1.0 Gbit connection in its adapter status. Speedtest.net shows 35 mbit/s down on the new computer Speedtest.net shows 78 mbit/s down on the old rusty IBM notebook. We have an 120 mbit down internet connection, which we we truly receive on another pc (also directly connected to the router) How to get the 1.0 Gbit going in the new pc ?

    Read the article

  • What's the best way to migrate SELECT applications and data from an old Mac to a one?

    - by jaydles
    I know I can make an easy transfer of everything using time machine, but I'm trying to transfer the minimum necessary to the new computer (applications I currently use, Aperture database, etc.) in order to keep the new machine as clean as possible, and avoid starting out with any legacy problems with permissions, etc. Clearly, I can copy individual apps and databases to an external drive and then install them on the new machine, but I'm trying to find an easier way.

    Read the article

  • Replacing all disks in a non-OS RAID 5 volume

    - by molecule
    Hi all, We currently have a server with 8 x HDD slots. It is a HP DL380G5 with a P400 controller. 2 x HDD are in a RAID 1+0 config and this hosts the OS. 6 x HDD are in a RAID 5 config and holds an Oracle DB. Basically the RAID 5 volume is running out of space and we would like to swap all 6 with higher capacity disks. Excuse my ignorance as I am pretty new to this... I believe we will need to backup the data, delete the RAID volume, insert the new disks, recreate the volume, and restore the data. 2 questions: Do we need to worry about the OS partition or is it completely independent so we can simply take out the 6 and insert 6 new disks and get the controller to recognize the 6 new disks and form a new RAID 5 volume? We should not need to reinstall OS or Oracle correct? Since we are going to restore the data on the volume from another source (our vendor will take care of this) but we would like to keep the existing data on the 6 disks just in case we run into issues and want to fall back, is this possible? Thanks in advance.

    Read the article

  • Problem upgrading kernel on debian 3.1

    - by exhuma
    Hi, I have a quite old box in a remote server farm. So I have no direct access. Only remote SSH (and via SSH to a serial console). I haven't updated this box in ages. Now, whenever I want to install a new package, a dependency to glibc appears. Unfortunately, the install of glibc depends on a 2.6 kernel and I am running a venerable 2.4 kernel (one more reason to upgrade). The problem is, that the install of a new kernel has an indirect (over locales) dependency to glibc. So, to install glibc, I need a new kernel. For a new kernel, I need to upgrade glibc. Essentially I am blocked. What's the best way to proceed considering I have no "hardware" access? Here's a quick transcript of the upgrade process: [green:~]% sudo aptitude install linux-image-686 Reading Package Lists... Done Building Dependency Tree Reading extended state information Initializing package states... Done Reading task descriptions... Done The following packages are unused and will be REMOVED: gcc-4.3-base The following NEW packages will be automatically installed: dash libc6-i686 libparse-recdescent-perl linux-image-2.6-686 linux-image-2.6.18-6-686 module-init-tools yaird The following packages have been kept back: adduser apache2 apache2-mpm-prefork apache2-utils apache2.2-common apt apt-utils aptitude autoconf autotools-dev awstats base-files base-passwd [...snip...] util-linux vacation vim vim-common wamerican wbritish wget whiptail whois wwwconfig-common zlib1g The following NEW packages will be installed: dash libc6-i686 libparse-recdescent-perl linux-image-2.6-686 linux-image-2.6.18-6-686 linux-image-686 module-init-tools yaird The following packages will be upgraded: hotplug libc6 2 packages upgraded, 8 newly installed, 1 to remove and 277 not upgraded. Need to get 0B/22.7MB of archives. After unpacking 52.1MB will be used. Do you want to continue? [Y/n/?] Writing extended state information... Done Preconfiguring packages ... (Reading database ... 34065 files and directories currently installed.) Preparing to replace libc6 2.3.6.ds1-13 (using .../libc6_2.7-18lenny2_i386.deb) ... Checking for services that may need to be restarted... Checking init scripts... WARNING: init script for postgresql not found. [ --- libc6 config screen appears here --- ] WARNING: POSIX threads library NPTL requires kernel version 2.6.8 or later. If you use a kernel 2.4, please upgrade it before installing glibc. The installation of a 2.6 kernel _could_ ask you to install a new libc first, this is NOT a bug, and should *NOT* be reported. In that case, please add etch sources to your /etc/apt/sources.list and run: apt-get install -t etch linux-image-2.6 Then reboot into this new kernel, and proceed with your upgrade dpkg: error processing /var/cache/apt/archives/libc6_2.7-18lenny2_i386.deb (--unpack): subprocess pre-installation script returned error exit status 1 Errors were encountered while processing: /var/cache/apt/archives/libc6_2.7-18lenny2_i386.deb E: Sub-process /usr/bin/dpkg returned an error code (1) Ack! Something bad happened while installing packages. Trying to recover: dpkg: dependency problems prevent configuration of locales: locales depends on glibc-2.7-1; however: Package glibc-2.7-1 is not installed. dpkg: error processing locales (--configure): dependency problems - leaving unconfigured Errors were encountered while processing: locales Reading Package Lists... Done Building Dependency Tree Reading extended state information Initializing package states... Done Reading task descriptions... Done Now, if I follow the instrunctions as promted I get the following. Note that I am using aptitude instead of apt-get to benefit from the better dependency tracking. I did try with apt-get first. But that let me to the same problem. [green:~]% sudo aptitude install -t etch linux-image-2.6.26-2-686 Reading Package Lists... Done Building Dependency Tree Reading extended state information Initializing package states... Done Reading task descriptions... Done E: Unable to correct problems, you have held broken packages. E: Unable to correct dependencies, some packages cannot be installed E: Unable to resolve some dependencies! Some packages had unmet dependencies. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following packages have unmet dependencies: linux-image-2.6.26-2-686: Depends: initramfs-tools (>= 0.55) but it is not installable or yaird (>= 0.0.13) but it is not installable or linux-initramfs-tool which is a virtual package. Any ideas?

    Read the article

  • Windows Media Center doesn't see my movies

    - by DrJekyll
    I am trying to configure my Windows Media Center (Windows 7 Ultimate). I selected folder with my movies and added it to the library, but when I went to the movies library, it says "There are no items in this library yet - Windows Media Center is searching for media files in the background...". I have all necessary codecs installed, Windows Media Player opens those movies correctly. When I right click on the file - Open with - Windows Media Center it also plays them without any problem. Any ideas why they don't appear in the libraries? Edit: Movies are coded with divx and xvid codecs and they have ".avi" extension. Windows doesn't have problems playing them. I told Media Center where the files are. I even pointed Windows Media Center to a folder with only one .avi file it still couldn't find anything there. (I have given it quiet some time, even though searching in the directory with only one file shouldn't take more than a few seconds.) When I add a folder with a lot of movies, I get a dialog box "You can wait while media is added or select OK to continue using Windows Media Center.".                                                                        At the end it says it added about 90 movies, but when I go to the libraries, it's still empty.

    Read the article

< Previous Page | 562 563 564 565 566 567 568 569 570 571 572 573  | Next Page >