Search Results

Search found 19703 results on 789 pages for 'virtual ip'.

Page 569/789 | < Previous Page | 565 566 567 568 569 570 571 572 573 574 575 576  | Next Page >

• DNS point to server on ISP and keep shared host too?

  - by Dwayne

  I know this is probably quite easy to do, but I might just have the right search sorted out... so here is the situation: We have example.com set up as a hosted server along with app1.example.com, app2.example.com and a few others. What I would like to do is set up the right zone file to also make our internal server addressable from the outside world as internalapp.example.com. This server sits behind a firewall (pfsense) and is hooked up to the world via a cable modem that is technically on DHCP from our ISP, but has had the same external IP for the past 15 months so far. What would be the best way to set this up?

  Read the article

• Is Samba "remote browse sync" possible across OpenVPN tunnel?

  - by John Reynolds

  I'm connecting 2 TomatoUSB (Shibby build on WNR3500L v2) routers with an OpenVPN routed connection: ----------------------- ----------------------- | Router 1, subnet 20 | <--tunnel--> | Router 2, subnet 21 | ----------------------- ----------------------- Router 1 is the OpenVPN server and Router 2 is a client. Clients attached to the routers on both subnets can ping clients on the other subnet, so the tunnel and routing works. I've enabled file sharing on both, in order to get their Samba WINS servers running. Is it possible to get name resolution across the tunnel? I've tried remote browse sync = 192.168.21.1 in /etc/smb.conf on the server side, to no avail. Also tried using the IP adress that the client gets from the OpenVPN address pool (usually 10.8.0.something), but still no joy.

  Read the article

• Windows 2008 server unaccessible without traces in the event log

  - by Rob

  I am trying to figure out why a Windows 2008 server became inaccessible in terms of RDP and access to a web application. The server was turned off and then on. Look at the event log at the time it went offline, I can't find anything. And looking at misc application logs, the system was running like normal after it went offline. It has to be said that by mistake the firewall was switched off earlier, so a lot of attempts had been done to access the SQL Server with the sa user as well as RDP login. But the attempts has been going on for days, so nothing new about that. Besides the event logs, is there anywhere else I can go to examine the cause of this? I am also in doubt whether or not a DOS attack or similar would show up in the event log. From a log for a backup application running on this server I can see that an attempt was done to access a remote IP after the server went offline, but got no connection.

  Read the article

• Using nginx as a reverse proxy for tomcat results in new jsessionids for every ssl request

  - by user439407

  I am using nginx as a reverse proxy for a tomcat setup, and everything works fine for the MOST part, the only issue I am having is that every request to an http address results in a new JSESSION ID being created(this doesn't happen in http), here is the relevant part of the NGINX configuration: location / { proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-Proto https; proxy_redirect off; proxy_connect_timeout 240; proxy_send_timeout 240; proxy_read_timeout 240; proxy_pass http://localhost:8080; } Any idea why I am constantly genning new jsessionids?

  Read the article

• How to failover to local account on a cisco switch/router if radius server fails?

  - by 3d1l

  I have the following configuration on a switch that I testing for RADIUS authentication: aaa new-model aaa authenticaton login default group radius local aaa authentication enable default group radius enable aaa authorization exec default group radius local enable secret 5 XXXXXXXXX ! username admin secret 5 XXXXXXXXX ! ip radius source-interface FastEthernet0/1 radius-server host XXX.XXX.XXX.XXX auth-port 1812 acct-port 1813 key XXXXXXXXX radius-server retransmit 3 ! line con 0 line vty 5 15 Radius authentication is working just fine but if the server is not available I can not log into the router with the ADMIN account. What's wrong there? Thanks!

  Read the article

• Lan DNS not working after reinstall of Ubuntu 13.10

  - by DrorCohen

  I upgrade my Ubuntu desktop to 13.10. When I say upgrade I mean installed on a new partition from scratch (old partition is available if To the problem: I'm trying to ping a host (Drobo-FS server) by it's host name. I get "Unknown Host". However pinging from another computer on the same lan - works fine (a laptop with 12.04 lts). for that matter every ping from the 13.10 to the local lan by hostname fails, ping with ip works. I don't have a local DNS server but somehow all the other computers in the network find each other by host name - only this new one fails... help appreciated...

  Read the article

• Starting VMs with an executable with as low overhead as possible

  - by Robert Koritnik

  Is there a solution to create a virtual machine and start it by having an executable file, that will start the machine? If possible to start as quickly as possible. Strange situation? Not at all. Read on... Real life scenario Since we can't have domain controller on a non-server OS it would be nice to have domain controller in an as thin as possible machine (possibly Samba or similar because we'd like to make it startup as quickly as possible - in a matter of a few seconds) packed in a single executable. We could then configure our non-server OS to run the executable when it starts and before user logs in. This would make it possible to login into a domain.

  Read the article

• VPN Configuration

  - by Josh

  How can I allow incoming connections on a Windows 7 machine that is connected to VPN? I have some services listening on certain ports that I have forwarded from my router. When the VPN is disconnected, I can connect to these services from my internal network as well as from the Internet without issue. When I connect my VPN however, I am still able to access the ports from my internal network, but not remotely. I think I need a split tunnel setup, and there is an option in the VPN settings to Use Default Gateway on remote network. I want this option enabled so all my traffic is routed through the VPN, but I want incoming connections to be allowed on my internal network IP from the Internet. Is there some hybrid way to set this up with routing?

  Read the article

• Can't see a Windows XP computer on the network

  - by user56614

  I have two PC's connected to the same router. One is running Vista Home Premium and the other is running XP Pro. I'm trying to reach the shares of second PC from the first PC. I've enabled file sharing on the XP PC, I've disabled firewall and defender, and I can successfully ping it from the Vista PC. Both computers are set to the same workgroup "WORKGROUP". However, if I try to type "\\192.168.1.2" in Windows Explorer (192.168.1.2 being the IP address of the XP PC), I get a message: "Windows can't access \\192.168.1.2... Error code: 0x80004005 Unspecified error". And If I type "net view \\192.168.1.2" in command prompt, I get "System error 53 has occurred. The network path was not found." Am I missing something trivial?

  Read the article

• Workaround for API limits [closed]

  - by blunders

  Problem: Planning on building out a client services company that requires access to APIs. Most APIs are limited based on user, IP, etc. - and even though the API calls would be on a per client basis, there's no way to get usage not tied to IPs. (Theoretical) Solution: Have each client install on their network a proxy/VPN that would allow my systems to connect and use their assigned usage. So, it's possible there's a better solution than the one I've thought of, but it's the only one I've been able to come up with.

  Read the article

• IIRF - Redirecting all traffic to the http equivalent

  - by GordonB

  I'm using IIRF and having some trouble getting it to redirect all traffic to the secure version of my sites. So... I have a website with about 20 apps in virtual directories in IIS6. The website takes 80 and 443 traffic. I want to use IIRF to redirect all port 80 traffic EG; http://myserver/app1/page1/param1 http://myserver/app2/ http://myserver To the secure equivalent (https). Here's my config so far; # Iirf.ini # # ini file for IIRF # RewriteLogLevel 1 RewriteLog D:\Websites\Apptemetry\IirfLogs RewriteEngine ON StatusInquiry ON IterationLimit 5 RewriteLogLevel 3 RewriteCond %{HTTPS} off RewriteCond %{SERVER_PORT} ^80$ RedirectRule ^http(.*)$ https$1 Can anyone advise the correct configuration to use, to redirect all traffic?

  Read the article

• Running 32 bit SQL Server 2005 on 64 bit Windows Server?

  - by TooFat

  If I have a 32 bit version of SQL Server 2005 running on a 64 bit Windows Server does the max amount of memory avail. the SQL Server process increase from 2gb to 4gb. In reading this blog entry by Mark Russinovich in which he states that "All Microsoft server products and data intensive executables in Windows are marked with the large address space awareness flag" and "Because the address space on 64-bit Windows is much larger than 4GB, something I’ll describe shortly, Windows can give 32-bit processes the maximum 4GB that they can address and use the rest for the operating system’s virtual memory." which leads me to believe that the answer is "yes" but I not totally confident.

  Read the article

• User for Public Network

  - by user71604

  my computer can catch the signal for many Access Points for the same network, while the network has problem with internet connection in some APs and it's working in others "all APs have the same SSID" Please advice if as i user i can force my computer to connect with specific AP neither than to go with the one with higher power (through MAC adress or IP)?. I am sure that my computer catch more than 10 signals for APs"All with same SSID". I am using windows 7 home primume 64 bit. as a user i dont have access to the AP config.

  Read the article

• Remote Desktop Problem on Windows Server 2008 R2

  - by lukiffer

  Revised this question to be more concise, consolidating several revisions. Symptoms: From a domain-member Windows 7 Client: Domain credentials to a domain controller = success Domain credentials to a member server (by hostname or FQDN) = success Domain credentials to a member server (by IP) = fail Local credentials to a member server (by either) = success From a non-domain-member Windows 7 Client: Domain credentials to a domain controller = success Domain credentials to a member server = fail Local credentials to a member server = success (Identical behavior from a Mac RDC 2.1 client) Server Configuration Details: Windows 2008 R2 Datacenter w/ SP1 The domain in question is a subdomain of a Windows 2008 domain (forest root). Root has DCs in both Site A and Site B, subdomain only has DCs in Site B. RDP is operating normally on all root member-servers and DCs. No remote desktop settings are defined by GPOs. Network level authentication is enabled; all clients are compatible and the certificate exchange/SSL handshake completes successfully. Not catching any errors in netlogon log.

  Read the article

• Setting up a transparent proxy with only one box.

  - by Scott Chamberlain

  I am playing around with transparent proxies, unfortunately I do not have two machines to test it out with. The current way I am doing things is the program makes a request to a computer on port 80, I use iptables -t nat -A OUTPUT -p tcp --destination-port 80 -j REDIRECT --to-port 1234 to redirect to my proxy that I am playing with. the proxy will send out a request to port 81 (as all outbound port 80 are being fed back in to the proxy so I want to do something like iptables -t nat -A OUTPUT -p tcp --destination-port 81 -j DNAT --to-destination xxxx:80 The problem lies with the xxxx part. How do I change the destination port without changing changing the destination ip? Or am I doing this setup completely wrong, I am learning after all and constructive criticism is definitely appreciated. The machine I am using is pretty low end so I would like not not have to create a VM with a second box unless absolutely necessary.

  Read the article

• Access Configuration Page of Modem (in bridge mode) through router

  - by Ujjwal Singh

  Given the Network Configuration: Internet (121.243.x.y/27) | (121.243.x.z) Static : Public Global IP Modem Bridge Mode | WiMAX (192.168.1.1/24) +169.254.1.1/24 : Modem Configuration Page | (192.168.1.2) Router DLink DIR 615 | Ethernet + WiFi (192.168.0.1/24) | Local network (192.168.0.2) Workstation Ethernet | no WiFi Is there any way, maybe using Routing Tables, to access the Modem configuration page at 169.254.1.1 from my local network, using a Windows 7 PC? Note that the modem is currently able to display its configuration page at 169.254.1.1, i.e. even while it is in bridge mode.

  Read the article

• Moved VM doesnt work correctly on my Ubuntu machine

  - by tinny

  Hi I have a Windows 7 VM that I have moved onto my Ubuntu 64bit host machine that is running VMware player 3.1.0. I think the VM was created on a Windows host. The problem I have is that when I login to this VM the screen goes blank and stays that way. The login screen is fine, but the desktop never correctly appears and sort of shows some strange pixelation that is all distorted. Seems like a virtual video card issue? If I boot into safe mode the desktop appears fine. Any ideas? Thanks

  Read the article

• When load balancing, must all copies of static web page be exactly the same?

  - by Gilles Blanchette

  I am used to get answers for everything on the web, but not this time... Yesterday I enable Amazon DNS weight functionally to load balance 7 websites between two different IP addresses (split 50%-50%). Both servers run IIS 8.5, sites runs well on both sides. Today I found out that Google WebMasterTools is reporting fails error with file robots.txt, all close to 50% of access try errors. The robots.txt file is ok and accessible (even via Google testing URL page) on both servers. Lets say current version of static web pages are on the first computer and the updated version of the same web pages are on the second computer. Can it be the problem? When load balancing, can static web pages be slightly different from one host server to the other? Thank you for your help

  Read the article

• Cannot access Samba Share that is on Linux

  - by doug

  I have 3 virtual machines; Windows Server 2012, Windows 8, and CentOS Linux. The Server is configured with active domain. The CentOS VM has a Samba Share which has rights for the domain Administrator. Now, the Windows Server 2012 DC can successfully locate the share, but cannot access it (with Admin) ? Is it not possible for the Server to have access to it has Domain Client Admin, not Server Admin ? Hope this is clear? Thanks

  Read the article

• iptables: How to create a rule for a single website that does not apply to other websites?

  - by Kris

  Virtual Dedicated Server hosts 10 websites. 1 firewall made with iptables If one of those 10 websites gets hit by too many ping requests coming from one IP address, how do I limit or drop it without dropping it for the other 9 websites? Do I create a firewall for every website ? If so, how? Or is it better to change my rules? If so, how? Thank you. Original question was posted here iptables: what's best practice when there're several websites but you want to use a rule for a single website? but it was too vague. Let me know if more info is needed.

  Read the article

• How to install libcrypt-ssleay-perl in Ubuntu?

  - by Deqing

  When I tried to install libcrypt-ssleay-perl, it says: $ sudo apt-get install libcrypt-ssleay-perl Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: libcrypt-ssleay-perl : Depends: perlapi-5.12.4 but it is not installable E: Unable to correct problems, you have held broken packages. This perlapi-5.12.4 is actually a virtual package provided by perl-base, which I had already installed: $ dpkg -l|grep perl-base ii perl-base 5.14.2-6ubuntu2.1 minimal Perl system So what should I do to install libcrypt-ssleay-perl now?

  Read the article

• Make exact copy of USB stick [closed]

  - by Andrius Palivonas

  There's this school software on a USB drive. It only runs, when the stick they gave is plugged in. Cloning the drive with dd command didn't work. I'm guessing it checks the hardware ID of the flash drive. Is there any way to change drives information? I guess not, but is it possible to create a virtual flash drive with exactly same hardware id and all other read-only information that the software is most probably checking. EDIT: The paper math books we have dont' have answers. So when I'm doing homework I have no idea if did it right. The electronic version does have the answers. The publisher didn't put them into paper version because of simple reason - money. They would have to republish the book if some answers are found to be wrong. So I feel no shame trying to pirate that software, because publishers are ruining our math education.

  Read the article

• Permission denied on network share

  - by Philipp

  i have a Windows 8 host system running a virtual(hyper-v) Debian6 client with an lamp environment. My development environment runs under Windows and I mapped the folder with my php files to a network drive so Apache has access to them.(mount.cifs //pc/share /var/share/) This far no problems - I see my app on windows in the browser. The problem is, I can't write stuff in php to the share folder - everytime i got a permission denied message in my error logs. For testing purpose i tried to change the directory permissions of /var/share with chmod -R 777 /var/share without success. Now Iam a little bit stumped.. has anyone an idea how to solve this?

  Read the article

• How can I launch a GUI session on a remote Ubuntu Desktop via SSH from a non-GUI Linux shell?

  - by Vihung

  I am setting up a test environment, made up of various Linux boxes, and I have the need to launch an instance of Firefox on a remote machine via ssh. The remote machine has Ubuntu Desktop (11) and Firefox installed. The source machine is a Continuous Integration server and it creates an ssh session to the remote machine from a non-GUI environment. It then runs a script, which tries to launch Firefox on the remote machine. However, since the ssh session is a from a non-GUI environment, there is no display. Is it possible to have a headless X-windows display? i.e. a virtual display in the remote environment for Firefox to run in? What options do I have?

  Read the article

• SSL issues with puppet agent at openSUSE

  - by Roman Grazhdan

  I have a master running at my vps, and it has a simple helloworld manifest which works fine with any ubuntu machine I have. It connects, exchanges keys and creates test file allright, so I'm sure it's not server issue. The agent which is running at a virtual machine with openSUSE says: err: Could not request certificate: SSL_connect returned=1 errno=0 state=SSLv3 read server certificate B: certificate verify failed. This is often because the time is out of sync on the server or client I believe it's probably a broken or missing lib, since the package is not built very accurately - it wouldn't start out of the box because of wrong path to lockfile, for example. So how do I figure out what exactly is wrong here? The time is allright, I've checked it. I probably could do without SSL if it's possible, since that SUSE machines are just for training, but it's the last opportunity.

  Read the article

< Previous Page | 565 566 567 568 569 570 571 572 573 574 575 576  | Next Page >