Search Results

Search found 6942 results on 278 pages for 'enabled'.

Page 57/278 | < Previous Page | 53 54 55 56 57 58 59 60 61 62 63 64  | Next Page >

• Issue booting Linux Mint from Live CD?

  - by Vee

  I had Windows 8 and Linux Mint 15 dual booted on my laptop. When I first installed Linux, I wasn't able to load into because the grub would not show. To fix this, I used boot-repair from a Live CD. This time, I updated to Windows 8.1 and it showed a watermark telling me my secure boot wasn't configured properly. I then went and enabled secure boot (BIOS) and I believe it was after that that the Grub would not show once again. I tried to boot from a Linux CD again but when I try, it gives me the following errors: error: failure reading sector 0x0 from 'hd1' error: you need to load the kernel first. Press any key to continue... Before, it was giving me an error with sector 0x6d200 or something instead of 0x0. I am completely unsure of what to do. I do not know what other details to give except that this my have happened after I enabled secure boot, and I actually clicked reset to default setting so I am unsure if any other settings were changed in the BIOS menu.

  Read the article

• Debian network bridge configuration - /etc/network/interfaces

  - by Mathias

  I'm running a Lenny Xen dom0 hosting multiple virtual machines in a routed IP setup. To get an additional private subnet, I created the bridge xenbr0 in the dom0 with the following commands: brctl addbr xenbr0 ifconfig xenbr0 10.0.0.1 netmask 255.255.255.0 ifconfig xenbr0 up This works as expected, and domU interfaces are added to the bridge by Xen on VM start. My only problem is: how the heck do i specify this configuration in /etc/network/interfaces that it remains permanent and the bridge is available after a reboot? I tried the following config as found on a lot of tutorials: auto xenbr0 iface xenbr0 inet static address 10.0.0.1 netmask 255.255.255.0 network 10.0.0.0 broadcast 10.0.0.255 bridge_stp no I get 2 different errors, depending on if the bridge already exists or not. If it doesn't exist: root@dom0:~# brctl show bridge name bridge id STP enabled interfaces root@dom0:~# /etc/init.d/networking restart Reconfiguring network interfaces...if-up.d/mountnfs[eth0]: waiting for interface xenbr0 before doing NFS mounts (warning). SIOCSIFADDR: No such device xenbr0: ERROR while getting interface flags: No such device SIOCSIFNETMASK: No such device SIOCSIFBRDADDR: No such device xenbr0: ERROR while getting interface flags: No such device xenbr0: ERROR while getting interface flags: No such device Failed to bring up xenbr0. done. And if it exists: root@dom0:~# brctl show bridge name bridge id STP enabled interfaces xenbr0 8000.000000000000 no root@dom0:~# /etc/init.d/networking restart Reconfiguring network interfaces...if-up.d/mountnfs[eth0]: waiting for interface xenbr0 before doing NFS mounts (warning). RTNETLINK answers: File exists Failed to bring up xenbr0. done. Could anyone point me in the right direction please? The bridge works fine when created manually, i just need the right config file entries. The most tutorials I found add some devices to the bridge in the config, is that maybe the problem why it is not working? I don't have any interfaces I want to add to the bridge on creation as they get added later on VM start... Thanks, Mathias

  Read the article

• Enable Soap for PHP 5.5.x on CentOS 6.5

  - by Chris Mancini

  Unfortunately I have to support soap on my server for the Fedex webservice. I recompiled PHP enabling support and it works via CLI but not PHP-fpm. They both point to the same ini file and both show the module loaded, but only CLI shows the configuration values. Output of php -i | grep -i soap Configuration File (php.ini) Path => /usr/local/etc Loaded Configuration File => /usr/local/etc/php.ini Configure Command => './configure' '--prefix=/usr/local' '--with-config-file-path=/usr/local/etc' '--with-config-file-scan-dir=/usr/local/etc/php_user/' '--enable-fpm' '--enable-ftp' '--enable-libxml' '--enable-mbstring' '--enable-pdo' '--enable-soap' '--enable-sockets=shared' '--enable-zip' '--with-curl' '--with-fpm-group=nginx' '--with-fpm-user=nginx' '--with-freetype-dir=/usr/lib64/' '--with-gd' '--with-jpeg-dir=/usr/lib64/' '--with-libdir=lib64' '--with-mcrypt' '--with-openssl' '--with-pdo-mysql' '--with-pear' '--with-readline' '--with-tidy' '--with-xsl' '--with-zlib' '--without-pdo-sqlite' '--without-sqlite3' soap Soap Client => enabled Soap Server => enabled soap.wsdl_cache => 1 => 1 soap.wsdl_cache_dir => /tmp => /tmp soap.wsdl_cache_enabled => 1 => 1 soap.wsdl_cache_limit => 5 => 5 soap.wsdl_cache_ttl => 86400 => 86400 Output from php-fpm phpinfo(): Configuration File (php.ini) Path /usr/local/etc Loaded Configuration File /usr/local/etc/php.ini SOAP Brad Lafountain, Shane Caraveo, Dmitry Stogov Please help, I have tried so many things...

  Read the article

• howto configure mod_proxy for apache2, jetty

  - by Kaustubh P

  Hello, This is how I have setup my environment, atm. An apache2 instance on port 80. Jetty instance on the same server, on port 8090. Use-Case: When I visit foo.com, I should see the webapp, which is hosted on jetty, port 8090. If I put foo.com/blog, I should see the wordpress blog, which is hosted on apache. (I read howtos on the web, and installed it using AMP.) Below are my various configuration files: /etc/apache2/mods-enabled/proxy.conf: ProxyPass / http://foo.com:8090/ << this is the jetty server ProxyPass /blog http://foo.com/blog ProxyRequests On ProxyVia On <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPreserveHost On ProxyStatus On /etc/apache2/httpd.conf: LoadModule proxy_module /usr/lib/apache2/modules/mod_proxy.so LoadModule proxy_balancer_module /usr/lib/apache2/modules/mod_proxy_balancer.so LoadModule proxy_http_module /usr/lib/apache2/modules/mod_proxy_http.so LoadModule proxy_ajp_module /usr/lib/apache2/modules/mod_proxy_ajp.so I have not created any other files, in sites-available or sites-enabled. Current situation: If I goto foo.com, I see the webapp. If I goto foo.com/blog, I see a HTTP ERROR 404 Problem accessing /errors/404.html. Reason: NOT_FOUND powered by jetty:// If I comment out the first ProxyPass line, then on foo.com, I only see the homepage, without CSS applied, ie, only text.. .. and going to foo.com/blog gives me a this error: The proxy server received an invalid response from an upstream server. The proxy server could not handle the request GET /blog. Reason: Error reading from remote server I also cannot access /phpmyadmin, giving the same 404 NOT_FOUND error as above. I am running Debian squeeze on an Amazon EC2 Instance. Question: Where am I going wrong? What changes should I make in the proxy.conf (or another conf files) to be able to visit the blog?

  Read the article

• Configure an Azure VM for Dynamic DNS for Cloud Services

  - by Adam

  I am trying to setup an azure VM with proper DNS to allow multiple cloud services to communicate across cloud service boundaries. As I understand it, I need to provide my own DNS server. I do not have any on-premise infrastructure, so I am trying to configure an Azure VM to act as my DNS. This SO question (http://stackoverflow.com/questions/21858926/azure-how-to-connect-one-cloud-service-with-other-in-one-virtual-network) is very similar to my setup. This article (http://msdn.microsoft.com/en-us/library/windowsazure/jj156088.aspx) describes my particular case: Name resolution between virtual machines and role instances located in the same virtual network, but different cloud services Here is what I have done: Created Azure Virtual Network and declared subnets for each of my cloud services. Created an Azure VM (Windows 2012 R2) with DNS enabled RDP to the VM and enabled the DNS role and installed features Added the appropriate NetworkConfiguration xml section to each of my cloud services .csfg files Re-deployed my cloud services I have verified that I setup the virtual network and networkconfiguration properly because my cloud service hosts are able to communicate with each other if I use the internal ips. However, name resolution doesn't appear to be working, and it doesn't appear that my cloud service roles can communicate with my DNS server. How do I configure my VM so that my different cloud services roles register themselves with my DNS server? EDIT: I think I am 1 step closer to getting this to work. The cloud services that I was using are in an old affinity group which is not supported by VMs, so I was unable to add my VM into my virtual network. I created a new VNET in a new affinity group with my VM added into it. However, I still don't know how to configure the azure VM's DNS server so that the cloud services register themselves for name resolution. Also, an added bonus guaranteed to get a +1 would be to explain if it is possible to register a DNS entry for the VIP for an internal endpoint of my cloud services so we can get load balancing. Thanks!

  Read the article

• Installing SilverStripe on 000webhost.com (Free web host)?

  - by benwad

  Hi I'm trying to learn how to work Silverstripe so I extracted the tar file to my free hosting account. I then went on install.php and edited the permissions to meet the requirements set out in install.php but I still get two warnings from the 'webserver configuration' section: I can't tell what webserver you are running. Without Apache I can't tell if mod_rewrite is enabled. I can't tell whether mod_rewrite is running. You may need to configure a rewriting rule yourself. I looked in phpinfo() and mod_rewrite appears to be installed. I contacted the web host and they said it was to do with virtual directory paths, and I should add 'RewriteBase /' to the top of my .htaccess file in the public_html directory. However I did this and still had the same problem. The install.php script says that I can install it even with these warnings but when I press 'install' it brings me to a page with the following errors: Friendly URLs are not working. This is most likely because mod_rewrite isn't configuredcorrectly on your site. Please check the following things in your Apache configuration; you may need to get your web host or server administrator to do this for you: * mod_rewrite is enabled * AllowOverride All is set for your directory I also get this error message from the server: Warning: unlink(mysite/_config.php) [function.unlink]: Permission denied in /home/a2716553/public_html/install.php on line 701 000webhost.com says they have successfully installed Silverstripe on their user accounts without much configuration but I can't seem to find out how.

  Read the article

• domain2.com redirects to domain1.com in Apache

  - by Dmitry Mikhaylov

  I created new virtual host, but when I try to request it, Apache redirects me to another virtual host. What could cause this problem? <VirtualHost XXX.XXX.XXX.XXX:80 > ServerName domain1.com AddDefaultCharset utf-8 CustomLog /var/www/httpd-logs/domain1.com.access.log combined DocumentRoot /home/user/www/domain1.com ErrorLog /var/www/httpd-logs/domain1.com.error.log ServerAdmin [email protected] ServerAlias www.domain1.com SuexecUserGroup user user AddType application/x-httpd-php .php .php3 .php4 .php5 .phtml AddType application/x-httpd-php-source .phps php_admin_value open_basedir "/home/user:." php_admin_value sendmail_path "/usr/sbin/sendmail -t -i -f [email protected]" php_admin_value upload_tmp_dir "/home/user/mod-tmp" php_admin_value session.save_path "/home/user/mod-tmp" ScriptAlias /cgi-bin/ /home/user/www/domain1.com/cgi-bin/ </VirtualHost> <VirtualHost XXX.XXX.XXX.XXX:80 > ServerName domain2.com CustomLog /dev/null combined DocumentRoot /home/user/www/domain2.com ErrorLog /dev/null ServerAdmin [email protected] ServerAlias www.domain2.com SuexecUserGroup user user AddType application/x-httpd-php .php .php3 .php4 .php5 .phtml AddType application/x-httpd-php-source .phps php_admin_value open_basedir "/home/user:." php_admin_value sendmail_path "/usr/sbin/sendmail -t -i -f [email protected]" php_admin_value upload_tmp_dir "/home/user/mod-tmp" php_admin_value session.save_path "/home/user/mod-tmp" </VirtualHost> "apache2ctl -S" output: VirtualHost configuration: XXX.XXX.XXX.XXX:80 is a NameVirtualHost default server domain1.com (/etc/apache2/apache2.conf:266) port 80 namevhost domain1.com (/etc/apache2/apache2.conf:266) port 80 namevhost domain2.com (/etc/apache2/apache2.conf:284) XXX.XXX.XXX.XXX:443 is a NameVirtualHost default server domain1.com (/etc/apache2/apache2.conf:246) port 443 namevhost domain1.com (/etc/apache2/apache2.conf:246) wildcard NameVirtualHosts and _default_ servers: *:443 is a NameVirtualHost default server www.example.com (/etc/apache2/apache2.conf:239) port 443 namevhost www.example.com (/etc/apache2/apache2.conf:239) *:80 is a NameVirtualHost default server domain1.com (/etc/apache2/sites-enabled/000-default:1) port 80 namevhost domain1.com (/etc/apache2/sites-enabled/000-default:1)

  Read the article

• reverse proxy not rewriting to https

  - by polishpt

  I need your help. I'm having problems with reverse proxy rewriting to https: I have an alfresco app running on top of tomcat and as a front and an Apache server - it's site-enabled looks like that: <VirtualHost *:80> ServerName alfresco JkMount /* ajp13_worker <Directory /var/www/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined ServerSignature Off </VirtualHost> I also have a reverse proxy server running on second machine and i want it to rewrite queries to https. It's site-enabled looks like that: <VirtualHost 192.168.251.50:80> ServerName alfresco DocumentRoot /var/www/ RewriteEngine on RewriteRule (.*) https://alfresco/ [R] LogLevel warn ErrorLog /var/log/apache2/alfresco-80-error.log CustomLog /var/log/apache2/alfresco-80-access.log combined ServerSignature Off </VirtualHost> <VirtualHost 192.168.251.50:443> ServerName alfresco DocumentRoot /var/www/ SSLEngine On SSLProxyEngine On SSLCertificateFile /etc/ssl/certs/alfresco.pem SSLCertificateKeyFile /etc/ssl/private/alfresco.key SetEnvIf User-Agent ".*MSIE.*" nokeepalive ssl-unclean-shutdown \ downgrade-1.0 force-response-1.0 ProxyRequests Off ProxyPreserveHost On <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPass /alfresco http://192.168.251.50:8080/alfresco ProxyPassReverse /alfresco http://192.168.251.50:8080/alfresco LogLevel warn ErrorLog /var/log/apache2/alfresco-443-error.log CustomLog /var/log/apache2/alfresco-443-access.log combined ServerSignature Off </VirtualHost> Now, ProxyPass works, when I go to alfresco/alfrsco in a browser application opens, but rewriting to https doesn't work. Plese help. Regards when I go to 192.168.251.50 Tomcat configuration page shows up. When I go to 192.268.251.50:8080 - the same as above when I go to 192.168.251.50:8080/alfresco - alfresco app page shows app when I go to alfresco/alfresco - same as above when i go to https://alfresco or https://alfresco i get an error connecting to a server

  Read the article

• X11 performance problem after upgrading from Centos3 to Centos5 with an ATI Rage XL

  - by Marcelo Santos

  After upgrading a computer from Centos3 to Centos5 an application that does a lot of scrolling took a very high performance hit. top tells me that X is using a lot of CPU and that was not happening before. The machine has an ATI Rage XL with 8MB and X is using the ati driver as there is no proprietary ATI driver for this board on linux. The xorg.conf: Section "Device" Identifier "Videocard0" Driver "ati" EndSection Section "Screen" Identifier "Screen0" Device "Videocard0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 Modes "1024x768" "800x600" "640x480" EndSubSection EndSection Section "DRI" Group 0 Mode 0666 EndSection A similar machine that still has Centos3 installed is able to start DRI on the X server while this one is not, this is the Xorg.0.log for the Centos5 machine: drmOpenDevice: node name is /dev/dri/card0 drmOpenDevice: open result is -1, (No such device or address) drmOpenDevice: open result is -1, (No such device or address) drmOpenDevice: Open failed drmOpenDevice: node name is /dev/dri/card0 drmOpenDevice: open result is -1, (No such device or address) drmOpenDevice: open result is -1, (No such device or address) drmOpenDevice: Open failed [drm] failed to load kernel module "mach64" (II) ATI(0): [drm] drmOpen failed (EE) ATI(0): [dri] DRIScreenInit Failed (II) ATI(0): Largest offscreen areas (with overlaps): (II) ATI(0): 1024 x 1279 rectangle at 0,768 (II) ATI(0): 768 x 1280 rectangle at 0,768 (II) ATI(0): Using XFree86 Acceleration Architecture (XAA) Screen to screen bit blits Solid filled rectangles 8x8 mono pattern filled rectangles Indirect CPU to Screen color expansion Solid Lines Offscreen Pixmaps Setting up tile and stipple cache: 32 128x128 slots 10 256x256 slots (==) ATI(0): Backing store disabled (==) ATI(0): Silken mouse enabled (II) ATI(0): Direct rendering disabled (==) RandR enabled I also tried using EXA instead of XAA and setting: Option "AccelMethod" "XAA" Option "XAANoOffscreenPixmaps" "true" uname -a Linux sir5.erg.inpe.br 2.6.18-128.7.1.el5 #1 SMP Mon Aug 24 08:20:55 EDT 2009 i686 i686 i386 GNU/Linux rpm -qa | grep xorg-x11-server xorg-x11-server-utils-7.1-4.fc6 xorg-x11-server-sdk-1.1.1-48.52.el5 xorg-x11-server-Xvfb-1.1.1-48.52.el5 xorg-x11-server-Xnest-1.1.1-48.52.el5 xorg-x11-server-Xorg-1.1.1-48.52.el5 The drmOpenDevice error continues when using the suggested Option "AIGLX" "true".

  Read the article

• apache2: ssl_error_rx_record_too_long when visiting port 80?

  - by John

  Hi, I have an Ubuntu 10 x64 server edition machine. I got a second IP and configured /etc/network/interfaces like so (actual IPs and gateways removed): auto lo iface lo inet loopback #iface eth0 inet dhcp auto eth0 auto eth0:0 iface eth0 inet static address [ my first IP ] netmask 255.255.255.0 gateway [ my first gateway ] iface eth0:0 inet static address [ my second IP ] netmask 255.255.255.0 gateway [ my second gateway ] /etc/apache2/ports.conf: Listen 80 NameVirtualHost [ my first IP ]:80 NameVirtualHost [ my second IP ]:80 <IfModule mod_ssl.c> # If you add NameVirtualHost *:443 here, you will also have to change # the VirtualHost statement in /etc/apache2/sites-available/default-ssl # to <VirtualHost *:443> # Server Name Indication for SSL named virtual hosts is currently not # supported by MSIE on Windows XP. Listen 443 NameVirtualHost [ my first IP - some site is running SSL successfully using it ]:443 </IfModule> <IfModule mod_gnutls.c> Listen 443 </IfModule> /etc/apache2/sites-enabled/mysite.conf: <VirtualHost [my second IP ]:80> ServerName mysite.com Include /var/www/mysite.com/djangoproject/apache/django.conf </VirtualHost> Then when visiting http[mysite].com:80 or http[mysite].com (:// removed because serverfault doesn't allow me to post hyperlinks), I get: An error occurred during a connection to [mysite].com. SSL received a record that exceeded the maximum permissible length. (Error code: ssl_error_rx_record_too_long) My guess is that the configuration file is not being picked up, and apache is therefore looking for the default-ssl file, which is not in conf-enabled. If I were to configure that file properly, it seems I would successfully connect to whatever default directory is specified in the default-ssl file. But I want to connect to my website. Any ideas? Thanks in advance!

  Read the article

• Authenticated User Impersonation in Classic ASP under IIS7

  - by user52663

  I've recently moved one of our servers from Server 2003 and IIS6 to Server 2008 R2 and IIS7 (technically IIS7.5 I suppose). In doing so I am transitioning a small account management tool written in classic ASP and have run into a problem with user impersonation. Extensive searching hasn't been much help so far. Under IIS6, the site was configured to impersonate the logged-in user. Thus, if a domain admin logged in, he was able to run commands to create user directories, adjust permissions, etc. Using Procmon you can see the processes executing as that user. This worked fine. However, with the same code under IIS7, I am unable to get this behavior. I have enabled Basic Authentication, disabled Anonymous Auth, enabled impersonation and have changed the app pool to classic instead of integrated pipelining. Everything seems to be configured correctly, however, all the processes launched by the classic ASP site continue to run as the default AppPool identity and not the logged-in user. If it matters, programs are being launched with code such as: set Wsh = Server.CreateObject("WScript.Shell") Wsh.Run("cmd.exe /C mkdir D:\users\foo") Monitoring via Procmon shows cmd.exe being run as either "Classic .NET AppPool" or "DefaultAppPool" depending on the pipeline mode. Any suggestions on how to get the classic ASP site to impersonate and execute as the authenticated user would be great. Thanks!

  Read the article

• How can adding a server to a domain cause Remote Desktop to stop working?

  - by Adrian Grigore

  I have two dedicated with Windows 2008 R2 servers which I am using for Web hosting. One Server A is a domain controller, Server B should simply be added to the domain controlled by Server A. So I RDP'd into Server B and changed the system settings so that Server B is part of that domain. I entered my domain admin credentials, was welcomed to the domain and asked to reboot the server. So far everything seemed to work smoothly After rebooting, I could not open an RDP connection to Server B anymore: Remote Desktop can’t connect to the remote computer for one of these reasons: 1) Remote access to the server is not enabled 2) The remote computer is turned off 3) The remote computer is not available on the network Make sure the remote computer is turned on and connected to the network, and that remote access is enabled. I restored an older backup of Server B and switched off the firewall before adding the server to my domain. But the problem reoccurred just the same. What could be the reason for this? The domain is brandnew and I did not change any of the default settings. Could this be some kind of domain-wide default policy that shuts down RDP on any domain clients? Or perhaps it has to do with the fact that Server B is virtual? Thanks for your help, Adrian

  Read the article

• pgpoolAdmin keeps going straight back to it's login page

  - by user705142

  I'm trying to run pgpoolAdmin through nginx - it seems to be working properly, at least initially. I've gone through the initial set-up, which works fine, but now after logging in every link takes me straight back to the login page. It also shows japanese text instead of english, despite picking english in the installation. It seems to me just as if it was unable to save any user data, session information etc. I have javascript/cookies enabled, so it's not that. The ownership of the folder is nginx, and so too is pgmgt.conf.php, so it shouldn't be a problem with permissions. One potential issue is that I can't seem to see any confirmation that php postgresql support is enabled in the php info screen, despite the correct package installed and in the config line. Any ideas as to what's happening here? The nginx rules are pretty standard: server { # pg-pool admin listen 997; server_name localhost; root /opt/pgpooladmin; index index.php; location ~ .php$ { fastcgi_pass_header Set-Cookie; fastcgi_pass 127.0.0.1:9000; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_param PATH_INFO $fastcgi_script_name; fastcgi_index index.php; include fastcgi_params; } }

  Read the article

• Debugging a Drobo that chokes Windows 7x64 When Plugged In

  - by Pridkett

  I've had a love hate relationship with my Drobo for a long time. After two years of using it on a Linux box, I moved it over to a Windows 7 machine where it seemed to work just fine for a long time, but it was under very light usage. Mainly backups that never actually happened. Recently I began using it for additional backup services (through CrashPlan, which is great). This means the Drobo gets a lot more usage. Also it means that something interesting happens, the Drobo can choke my system on startup. Here's what I mean: Start computer without Drobo plugged in, CrashPlan and Drobo Dashboard services disabled: 105s Start computer with Drobo plugged in Crashplan disabled, Drobo Dashboard enabled: 250s (and 1 cpu at 100% for a very long time, drobo churning) Start computer with Drobo plugged in, CrashPlan and Drobo Dashboard disabled: 250s (1 cpu at 100% for a very long time, drobo churning) Start computer with Drobo plugged in, Crashplan and Drobo Dashboard enabled: 300s (1 cpu at 100% for a very long time, drobo churning) If I yank the USB plug on the Drobo the CPU usage goes down to nothing very quickly. The slow startup in the fourth scenario is because CrashPlan is trying desperately to load stuff up on the H: drive before it gives up, so I've disabled it for the time being. So here's my question: What the heck is going on when I plug the drobo in? I've fired up Process Explorer and see that the System process is hogging the CPU, specifically it's an ntoskrnl.exe/KdPollBreakIn thread that's going ape. Is this something that's wrong with Drobo? Windows? Any idea on how to find out? If it matters, here's tech info: Athlon 64x2 4400, 2GB RAM, Win7 Ultimate, Drobo USB (2x1TB, 2x320GB)

  Read the article

• Apache2 Virtualhost practice config issue

  - by sisko

  I am practicing virtualhost configuration. In my /var/www directory I have created 3 directories called test1, test2 and test3 each of which has a simple index.php script in it. I:E test1/index.php etc. In /etc/apache2/sites-available/test1 I have the following configuration: <VirtualHost *:80> ServerAdmin webmaster@localhost ServerName test1 DocumentRoot /var/www/test1 <Directory /> Options FollowSymLinks AllowOverride All </Directory> <Directory /var/www/test1/> Options -Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> ErrorLog ${APACHE_LOG_DIR}/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog ${APACHE_LOG_DIR}/access.log combined </VirtualHost> All the other sites have a similar virtualHost definition. I have enabled the site(the symlink appears in sites-enabled) and I have restarted apache. However, when I visit localhost/test1, I get a 404 Error. My error log show the following message: [Wed Oct 23 06:22:52 2013] [error] [client 127.0.0.1] File does not exist: /var/www/test1/test1 I don't know why I get the double test1/test1 in the error logs. I'm trying to find the right virtualHost setup which will allow all 3 test websites to be served from their URLs I:E test1/index.php, test2/index.php and test3/index.php. Can anyone help me out, please?

  Read the article

• Reduce power consumption of gaming computer while idle

  - by White Phoenix

  This is my current build: EVGA X58 (first generation) motherboard Intel i7 965 clocked @ 3.3 Ghz 3x DDR3-1600 Corsair RAM at stock timings and voltages Corsair AX750 80 Plus Gold PSU 1 Optical Drive 1 Seagate 7200.10 500 GB drive 2x Western Digital Caviar Black 1 TB drives OCZ Vertex 1 60 GB EVGA GTX 460 oc'd at 800/1600/1850 Antec 1200 case HT-Omega Striker 7.1 Sound Card Windows 7 32-bit Professional (PAE Enabled) I've already seen this post Reduce power use on computer and this post How do I lower power consumption of my computer and while useful, I'm looking for answers specific to my build and OS. I'm pretty sure this build is a energy-intensive build by default, but I want to try to reduce the amount of energy my build uses when I leave it idle (when I go to bed or go out, etc). The first requirement for this machine is that I need to leave it on, so I cannot turn it off while it's being unused. I run it as a file server for personal reasons and I also leave it on in case people leave me messages on various IM services and chat clients (IRC, MSN, Steam, XFire, Pidgin, etc). I'm also unable to replace the parts in my computer with a cheaper "greener" part. What are some ways to minimize the amount of power the machine uses? I'm already using a high efficiency power supply (80 Plus Gold), but I imagine there's other things that can be done in the BIOS and Windows' power settings to reduce power usage while I'm not using the computer. From what I can tell, I can't use Sleep since that'll disable network access (whole reason why I leave the computer on in the first place). I already turn off my monitor when it's not in use. I enabled Intel SpeedStep within the BIOS (I know, I have a 965 and why am I enabling SpeedStep?) Should I bring the graphics card back to stock speeds and lower the clock on the processor even more? Main reason why I'm asking is I think this computer alone is the reason why my power bill is high, so I want to reduce its consumption to as low as possible without having to shut the thing down.

  Read the article

• Setting "Run WWW service in IIS 5.0 isolation mode" does not persist in IIS 6

  - by Saul Dolgin

  Our IIS server was recently patched with the latest Microsoft Security Updates and since then, I am unable to enable the "Run WWW service in IIS 5.0 isolation mode" setting. This setting was enabled prior to patching and somehow changed during the updates. I have tried both using the IIS Manager console and the adsutil.vbs approach to change it. Either way, after resetting IIS for the change to take effect, when I go to verify that the isolation mode setting is enabled (true) I find that is reverts back to being disabled (false). Now... The patches have already been rolled back, however the setting still does not persist when I enable it. While I am trying to research the patches that were applied to see if there is a known issue (or perhaps a change in this setting's behavior) I was hoping someone else might have come across the same problem. Any help towards a workaround would be greatly appreciated! >cscript adsutil.vbs set W3SVC/IIs5IsolationModeEnabled TRUE IIs5IsolationModeEnabled : (BOOLEAN) True >iisreset Attempting stop... Internet services successfully stopped Attempting start... Internet services successfully restarted >cscript adsutil.vbs get W3SVC/IIs5IsolationModeEnabled IIs5IsolationModeEnabled : (BOOLEAN) False

  Read the article

• Why Virtual Box won't give me option to create 64 bits guests?

  - by Eduardo Born

  My host is x64 bits Windows 8.1. I downloaded the latest Virtual Box (4.3) and I'm trying to create a VM with a 64 bits Ubuntu OS (ubuntu-12.04.3-desktop-amd64). When I go to New VM wizard, it doesn't give me option to select "Ubuntu (x64)" as I have seen in other people's screenshots, only just "Ubuntu". As a result, the ISO can't boot. I tried in another PC and Virtual Box gives the x64 variants to most listed OS... Control Panel shows x64 OS, x64 processor. My host laptop is a Sony Vaio VPCZ22UGX/N, Intel® Core™ i7-2640M processor. CPUz shows Vx-t is available on my processor, of course. Here is what I tried so far: I enabled IO APIC as required in the docs. I have virtualization enabled in the BIOS. It works fine in VMware. Check that Hyper-V is not running or even installed on my Windows. Same for VMware. I also tried running the command: VBoxManage modifyvm [vmname] --longmode on for that VM, but no change.. I think the issue is really that I can't select x64 variant of the Ubuntu OS for that VM. Other people seem to indicate that's a requirement, but I don't get that option for some reason. I spent a lot of time and can't find what's wrong... Anyone knows what could be missing here? Thank you very much!! Eduardo

  Read the article

• Orphan IBM JVM process

  - by Nicholas Key

  Hi people, I have this issue about orphan IBM JVM process being created in the process tree: For example: C:\Program Files\IBM\WebSphere\AppServer\bin>wsadmin -lang jython -f "C:\Hello.py" Hello.py has the simple implementation: import time i = 0 while (1): i = i + 1 print "Hello World " + str(i) time.sleep(3.0) My machine has such JVM information: C:\Program Files\WebSphere\java\bin>java -verbose:sizes -version -Xmca32K RAM class segment increment -Xmco128K ROM class segment increment -Xmns0K initial new space size -Xmnx0K maximum new space size -Xms4M initial memory size -Xmos4M initial old space size -Xmox1624995K maximum old space size -Xmx1624995K memory maximum -Xmr16K remembered set size -Xlp4K large page size available large page sizes: 4K 4M -Xmso256K operating system thread stack size -Xiss2K java thread stack initial size -Xssi16K java thread stack increment -Xss256K java thread stack maximum size java version "1.6.0" Java(TM) SE Runtime Environment (build pwi3260sr6ifix-20091015_01(SR6+152211+155930+156106)) IBM J9 VM (build 2.4, JRE 1.6.0 IBM J9 2.4 Windows Server 2003 x86-32 jvmwi3260sr6-20091001_43491 (JIT enabled, AOT enabled) J9VM - 20091001_043491 JIT - r9_20090902_1330ifx1 GC - 20090817_AA) JCL - 20091006_01 While the program is running, I tried to kill it and subsequently I found an orphan IBM JVM process in the process tree. Is there a way to fix this issue? Why is there an orphan process in the first place? Is there something wrong with my code? I really don't believe that my simplistic code is wrongly implemented. Any suggestions?

  Read the article

• What does this error mean in my IIS7 Failed Request Tracing report?

  - by Pure.Krome

  Hi folks, when I attempt to goto any page in my web application (i'm migrating the code from an asp.net web site to web application, and now testing it) .. i keep getting some not authenticated error(s) . So, i've turned on FREB and this is what it says... I'm not sure what that means? Secondly, i've also made sure that my site (or at least the default document which has been setup to be default.aspx) has anonymous on and the rest off. Proof: - C:\Windows\System32\inetsrv>appcmd list config "My Web App/default.aspx" -section:anonymousAuthentication <system.webServer> <security> <authentication> <anonymousAuthentication enabled="true" userName="IUSR" /> </authentication> </security> </system.webServer> C:\Windows\System32\inetsrv>appcmd list config "My Web App" -section:anonymousAuthentication <system.webServer> <security> <authentication> <anonymousAuthentication enabled="true" userName="IUSR" /> </authentication> </security> </system.webServer> Can someone please help?

  Read the article

• PHP enable sqlite phpinfo states --without-sqlite

  - by Jahmic

  I've seen similar questions but none that address my situation adequately. I'm running Apache and PHP 5.3.6 on a amazon cloud server. phpinfo keeps stating that sqlite is disabled. At least that what it seems from the configure line: './configure' ... '--without-sqlite' In other parts of phpinfo() output: PDO PDO drivers mysql, sqlite PDO Driver for SQLite 3.x enabled SQLite Library 3.6.20 sqlite3 SQLite3 support enabled SQLite3 module version 0.7-dev SQLite Library 3.6.20 Directive Local Value Master Value sqlite3.extension_dir no value no value and at least one the following PHP commands fail: if (!extension_loaded('SQLite') OR !function_exists('sqlite_open')) Yum install states that both sqlite and pdo-lite are already installed. I've tried to enable sqlite by editing my local php.ini by adding: ; Enable sqlite3 extension module extension=sqlite3.so I've checked the main php.ini (/etc/php.ini) and there is nothing specific about disabling it. In fact, there is a sub-conig file loaded in php.d that also specifies this extension as well as another for the pdo-sqlite I'm running of things to look for or try. Any suggestions. How do I find where the PHP configure is stated? Thanks

  Read the article

• Enable FTP on OS X 10.8 Mountain Lion Server

  - by Oleg Trakhman

  There is a LAN comprising several mac machines (iMac, Mac Pro, macbook etc.), Airport Express router and Mac Mini Server running OS X Server 10.8 (Mountain Lion Server). I need to share a folder on Mac Mini Server by FTP. What did I try so far: Made special partition for FTP Access, call it "Reports" So shared folder would be "/Volumes/Reports" Gave access every user and group in system, and also enabled guest access. I checked posix acl, which is "rwxrwxrwx", I checked sharing settings in "Preferences.app" and "Server.app" Checked that users have access to FTP service Enabled FTP in Server.app I tried access to shared folder (by FTP): via Cyberduck via Finder via shell: ftp server.local And what I got: $ ftp [email protected] Trying 10.0.2.2... Connected to server.local. 220 10.0.2.2 FTP server (tnftpd 20100324+GSSAPI) ready. 331 User ftpuser accepted, provide password. Password: 530 User ftpuser may not use FTP. and $ ftp [email protected] Trying 10.0.2.2... Connected to server.local. 220 10.0.2.2 FTP server (tnftpd 20100324+GSSAPI) ready. 331 User admin accepted, provide password. Password: 530 User admin denied by SACL. ftp: Login failed ftp> (admin is administrator account , ftpuser is special user account made to access ftp) What I'm doing wrong? Getting really tired of this...

  Read the article

• Bad font anti-aliasing in Ubuntu

  - by Juliano

  I'm switching from Fedora 8 to Ubuntu 9.04, and I can't seem to get it to get a good font anti-aliasing to work. It seems that Ubuntu's fontconfig tries to keep characters in integral pixel widths. This makes text more difficult to read, when 1 pixel is too thin and 2 pixels is too thick. Check the image below. In Fedora, when fontconfig anti-aliasing is enabled, fonts have their thickness proportional to the font size. Below, the thickness is different for 8, 9 and 10pt sizes. In Ubuntu, on the other hand, even when anti-aliasing is enabled, all 8, 9 and 10pt sizes have 1 pixel thickness. This makes reading larges amount of text difficult. I'm using the very same home directory, and I already checked that X resources are the same in both systems: ~% xrdb -query | grep Xft Xft.antialias: 1 Xft.dpi: 96 Xft.hinting: 1 Xft.hintstyle: hintfull Xft.rgba: none GNOME settings: ~% gconftool-2 -a /desktop/gnome/font_rendering antialiasing = grayscale hinting = full dpi = 96 rgba_order = rgb So, the question is: What should I change in the new box (Ubuntu) in order to get anti-aliasing like in the old box (Fedora)?

  Read the article

• Poor SSL performance with vsftpd

  - by petrus

  I'm trying to tweak vsftpd to achieve maximum performance for my usage: I have only one or two clients that connect to the server. File size is between ~15MB and 1GB. Typical transfer batch represent between 1 and 2GB of data. For testing purposes, I'm using a tmpfs on both sides (thus eliminating any disks bottleneck) with a single 1GB file. When SSL is disabled, performance is good, with a transfer rate at ~120MB/s (reaching the limits of gigabit networking). With SSL enabled only for control traffic (and not data traffic), performance drops at about 112MB/s, which is still within the acceptable limits. However, when SSL is enabled for data flows, the transfer speed drops dramatically: 6.7MB/s using 3DES & SHA (ssl_ciphers=DES-CBC3-SHA in vsftpd.conf) 16MB/s using DES & SHA (ssl_ciphers=DES-CBC-SHA) I didn't tested other ciphers, but from what I can see from the CPU usage during the transfer, it seems that vsftpd is only using a single cpu/core per client. While this can fit for large ftp sites with hundreds of clients, I'd like to avoid this behavior and use more ressources on the server. On a side note, if you have any ideas regarding other openssl ciphers...

  Read the article

• httpd 2.2.15 + suPHP + suExec + php5 = permission and information ?

  - by Prix

  Hi, i am currently playing around with suexec, suphp, php5 on my apache on slackware 13.1. Everything is installed and working properly but now i did like to got further into the directory permissions and at suphp settings and options available. initially i was planning to leave suphp disabled unless a virtualhost has it specified to be enabled but it does not seem to work, see sample: mod_php.conf which is included in my httpd.conf # # mod_php & mod_suPHP - PHP Hypertext Preprocessor module # # Load the PHP module: LoadModule php5_module lib/httpd/modules/libphp5.so # Load the suPHP module: LoadModule suphp_module lib/httpd/modules/mod_suphp.so <IfModule mod_php5.c> # Tell Apache to feed all *.php files through PHP. If you'd like to # parse PHP embedded in files with different extensions, comment out # these lines and see the example below. <FilesMatch \.php$> SetHandler application/x-httpd-php </FilesMatch> </IfModule> <IfModule mod_suphp.c> # This option tells mod_suphp if a PHP-script requested on this server (or # VirtualHost) should be run with the PHP-interpreter or returned to the # browser "as it is". suPHP_Engine off </IfModule> With the above first sample it makes suPHP and PHP not work if i comment out the php5 stuff but the module it will run just fine ... So my first question is, how could i possible make this setup work ? Leave suPHP disabled using php5 by default and if a virtualhost has suPHP enabled it will disable php5 and use suPHP. if any information is lacked here please let me know and i will update with any additional information you may need. Thanks in advance.

  Read the article

< Previous Page | 53 54 55 56 57 58 59 60 61 62 63 64  | Next Page >