Search Results

Search found 20284 results on 812 pages for 'internet archives'.

Page 57/812 | < Previous Page | 53 54 55 56 57 58 59 60 61 62 63 64  | Next Page >

• Two NIC's 2 Internet Connections, 1 Windows Server 2008 RC2, Routing help required

  - by PJZ

  Hello, I have a Windows 2008 server and 4 other client machines on my home network. I have two internet connections. The main connection is setup with a home router and DHCP on that for all the clients on the network. The secondary connection is just a cable modem which is plugged directly into the server. Local Area Connection: This NIC has an external IP and is connected to the Cable Modem. Local Area Connection 2: This NIC has an internal IP (192.168.0.102) and allows access to all the internal computers. It also has internet access via the local router. So here lies the problem, I want to use the Cable connection on the server for the internet traffic (so that the traffic for server/clients are seperated) but I also need to maintain local access. I am wondering how to make it so that all the internet traffic goes via that NIC because at the moment it goes through the local NIC. As a secondary problem I would also like to forward the connection of one application used by the clients via the server and the cable/server internet because of poor routing for it on the main connection. This perhaps is something for another question though. Thanks for any help you can offer me. Regards PJ

  Read the article

• VPN Network intermittantly fails to provide internet: What could be possible causes

  - by Jake M

  We have a small office with our own VPN setup. We occasionally experience failures in our internet connection where we cannot access the internet. Most of the time the internet connection will resume by itself(without me doing anything) after a period of time(10 mins). Would you be able to suggest possible causes of the connection failure so I can then go and run some tests? Our network architecture is like so: A 'Billion' brand router that is connected to the internet via phone cable and then connected to our Cisco Switch A Cisco Switch/Bus which is connected to all our office nodes, our external harddrive and also to our router as stated above. All connections are via ethernet cable A series of work computers(nodes) connected via ethernet cable to the Cisco switch. Our ISP is TPG Australia We have a Virtual Private Network All the ethernet cables are about 3 years old Do you think that the causes of our intermittant connection problems could be due to the following: Data collisions in the ethernet cables Old/Faulty ethernet cables Our ISP has bad service Can you think of any other causes of the problem?

  Read the article

• downloading a file from the internet

  - by eugene

  when iam downloading a file from the internet it stops after some time usually around 14%

  Read the article

• downloading a file from the internet

  - by eugene

  when iam downloading a file from the internet it stops after some time usually around 14%

  Read the article

• Internet not working on a VirtualBox Linux machine

  - by mtahmed

  I installed VirtualBox on a Windows 7 PC and installed Xubuntu (Ubuntu with XFCE) on it. Now on the Windows, I am connected to the internet through a LAN which automatically authenticates to connect to the network(because its my work computer). I have also installed the guest additions on this virtual machine (Xubuntu). I tried both NAT and bridging to set up internet connection but I still cannot connect to the internet. For NAT: The browser doesn't say website not found but it keeps trying to load it forever and the network status monitor (the one provided by VirtualBox) doesn't show any green light (no incoming packets). For Bridging: Same as for NAT but the network status monitor shows incoming packets and outgoing packets. But internet still doesn't work. I tried a lot of different things but none worked.

  Read the article

• Restrict programs from accessing the Internet

  - by n0v1c3c0d3r

  I have a 256 kbit/s Internet connection. Most often, I find that the browsing speed is too slow. I have to use TCPView (SysInternals) to find out which program is accessing the Internet without my knowledge and terminate it. Previously I was using ZoneAlarm to control Internet access by installed programs. But as it doesn't work for Windows 7, I'm left with no option. Is there any other tool which serves the purpose?

  Read the article

• Internet is a series of tubes?

  - by Zoredache

  Almost all of use have heard of Ted Stevens trying to describe the Internet with the analogy that it is a series of tubes (mp3). I believe that it likely that some tech person somewhere tried to describe the Internet to him and this was the best analogy they could come up with. What analogy would you use to describe the Internet, and issues related to bandwidth, latency, etc, to your grandmother or someone else with no IT experience.

  Read the article

• Sharing internet connection over VPN in Windows XP

  - by Nigel Hawthorne

  How can I share my internet connection with VPN clients using the Windows XP built-in VPN server? I want to be able to use my home internet connection (on an XP machine) from my anywhere using my laptop (Windows 7 machine). The built-in VPN server in XP and the VPN client in Windows 7 seem to do a great job of giving me access to both machines securely over the internet, but I cannot find a way to use ICS in conjunction with the incoming connection to give access to my home internet connection to my laptop remotely. Is there a way to do this? or is there an alternative VPN server software that is not limited to only local access?

  Read the article

• I get "An error occurred while Windows was synchronizing with [name of time server]." when trying t

  - by ChrisF

  Prompted by the answers to this question I decided to give the Windows built in time synchronisation another go. However, no matter what time server I use I get this error: "An error occurred while Windows was synchronizing with [name of time server]." The help suggests the following as reasons for failure: You are not connected to the Internet. Establish an Internet connection before you attempt to synchronize your clock. Your personal or network firewall prevents clock synchronization. Most corporate and organizational firewalls will block time synchronization, as do some personal firewalls. Home users should read the firewall documentation for information about unblocking network time protocol (NTP). You should be able to synchronize your clock if you switch to Windows Firewall. The Internet time server is too busy or is temporarily unavailable. If this is the case, try synchronizing your clock later, or update it manually by double-clicking the clock on the taskbar. You can also try using a different time server. The time shown on your computer is too different from the current time on the Internet time server. Internet time servers might not synchronize your clock if your computer's time is off by more than 15 hours. To synchronize the time properly, ensure that the date and time settings are set close to your current time in the Date and Time Properties in Control Panel. Now the first reason is clearly wrong - I am connected to the internet. I can see the 2nd being the most likely cause. I have Sygate Personal Firewall running, but it normally asks if something it trying to connect for the first time. Does anyone know I can unblock the NTP protocol - or at least check if it is blocked?. I don't think it's #3 or #4 as I've tried a number of different servers including the one currently used by Atomic Clock Sync. Though if someone knows the address of a UK time server I can double check this.

  Read the article

• Fedora 15: em1 recently dissapeared and hostapd no longer serves internet to wirelessly connected devices

  - by Daniel K

  I have a laptop running hostapd, phpd, and mysql. This laptop uses an Ethernet connection to connect to the internet and acts as a wireless access point for my workplace's wifi devices. After installing some software and reconnecting my Ethernet elsewhere, my "em1" device is no longer present and wirelessly connected devices can no longer reach the internet. The software I recently installed is: pptp, pptpd, and updated some fedora libraries. I have also recently moved my desk and laptop to another location and thus had to reconnect the Ethernet elsewhere. Wifi devices no longer have access to the internet. Wirelessly connected devices are able to successfully log into the laptop, showing full strength, correct SSID, and uses the proper password. However, when I tried to connect to a site like google, the request times out. The device "em1" also no longer appears on my machine. Running: # ifup em1 will give me the following output: ERROR : [/etc/sysconfig/network-scripts/ifup-eth] Device em1 does not seem to be present, delaying initialization. And running: # dhclient em1 has the following output: Cannot find device "em1" When I run # dmesg|grep renamed, I get the following: renamed network interface eth0 to p4p1. I've tried to connect to the internet through p4p1 directly from the laptop and was successful. However, my wireless devices connected to my laptop are not able to connect to the internet. I have uninstalled pptp and pptpd using # yum erase ... but the problem still persists. To install pptp I used: # yum install pptp To install pptpd I did the following: # rpm -Uvh http://poptop.sourceforge.net/yum/stable/fc15/pptp-release-current.noarch.rpm # yum install pptpd To update my fedora libraries I used: # yum check-update # yum update EDIT: Running # route produces the following results: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 10.11.200.1 0.0.0.0 UG 0 0 0 p4p1 10.11.200.0 * 255.255.252.0 U 0 0 0 p4p1 172.16.100.0 * 255.255.255.0 U 0 0 0 wlan0

  Read the article

• Configure ubuntu 12.10 to share internet through second NIC with subnetwork

  - by Dan Smith

  I have an Ubuntu 12.10 box with 2 NICs. eth0 is connected to my 192.168.1.X network, which is connected to my home router and out to the internet. I want the other interface, eth1,to support 10.0.0.x and allow devices on that network to access the internet through my ubuntu box. I do not need dhcp on the 10.0.0.x network. Here's a schematic: Internet --- home router ---- ubuntu[eth0:192.168.1.x, eth1:10.0.0.x] --- [10.0.0.x device] How do I configure the ubuntu box to share the internet with devices on that subnetwork? Thanks!

  Read the article

• DIR-615 lose internet connection after 3 minutes

  - by Sirber

  I got a new DLink DIR-615 routeur. DSL model connects fine. Connected PCs connects to the internet fine (wireless, wired) fine too. After ~3 minutes, connected PCs cannot go to the internet. Web pages goes timeout, sometimes google talk stays on (working). From the router admin page, pings works correctly (on google.ca), so the connection is active. pc -- routeur -- internet: fail pc -- router: ok router -- internet: ok could it be firewall related? I've read there's a SPI firewall enabled.

  Read the article

• DIR-615 lose internet connection after 3 minutes

  - by user31375

  I got a new DLink DIR-615 routeur. DSL model connects fine. Connected PCs connects to the internet fine (wireless, wired) fine too. After ~3 minutes, connected PCs cannot go to the internet. Web pages goes timeout, sometimes google talk stays on (working). From the router admin page, pings works correctly (on google.ca), so the connection is active. pc -- routeur -- internet: fail pc -- router: ok router -- internet: ok could it be firewall related? I've read there's a SPI firewall enabled.

  Read the article

• Routing Traffic on Ubuntu to give Raspberry PI Internet Access

  - by Scruffers

  I'm hoping someone can point me in the right direction for setting up my Linux (Ubuntu 12.04) box to route traffic from eth0 to wlan0. I'll try and explain the problem I am trying to solve: I currently have two separate networks: [RaspberryPi/eth0] 192.168.2.2 / 255.255.255.0 ^ | v [Ubuntu/eth0] 192.168.2.1 / 255.255.255.0 And: [Ubuntu/wlan0] 192.168.1.100 / 255.255.255.0 ^ | v [ADSL router] 192.168.1.1 / 255.255.255.0 So currently if I want to access the RaspberryPI I can SSH from the Ubuntu box to the PI. And if I want to use the Internet, I have full access from the Ubuntu box, but nothing from the RaspberryPI - the two networks are partitioned. What I would like to do is configure things so that the RaspberryPI has Internet access via the Ubuntu box and out to the Internet. I tried to create a bridge, but got the message "wlan0: operation not supported" (wireless chipset is Ralink RT3062). I'm sure giving the Raspberry PI Internet access should be easy to do in this configuration, but I am a bit lost - can someone point me in the right direction please?

  Read the article

• Allowing a private subnet EC2 access to the internet - Amazon AWS

  - by Xavier Hutchinson

  I have a VPC "VPC with Public and Private Subnets" created via the VPC wizard which should include NAT for the private subnet VPCs however it's not working. They are unable to browse the internet, resolve internet names and ping internet IPs. This is a stock standard conf, I am very sure of that so I am unsure why it's not working. Perhaps there was something additional I am supposed to do that I don't know about? Thank you, Xavier.

  Read the article

• bridge to share WiFi internet connection over eth0

  - by rubo77

  In this script there is implemented that you create a mesh network and connect other machines to your device to serve an internet connection with dhcp: echo "starting bridge to share internet connection over eth0" ifconfig eth0 up promisc brctl addbr br-freifunk brctl addif br-freifunk bat0 brctl addif br-freifunk eth0 echo "internet starting, this may take some minutes due to latency..." echo "(use" echo "tail -f /var/log/syslog" echo "in another window for debugging)" echo echo dhclient br-freifunk echo "The error 'Rather than invoking init scripts through /etc/init.d...' can be ignored:" dhclient br-freifunk # without bridge: dhclient bat0 This works fine with the freifunk-mesh network. But how can I serve internet in a normal case? I would like to connect to any open Wifi I find with my network-manager or wicd (yes, with the graphical GUI) and then start a small script that creates a bridge to my network-out on my laptop I use Ubuntu and my networkcards are eth0 and wlan0

  Read the article

• Javascript onclick event is not working in internet explorer 8.

  - by Mallika Iyer

  Hi, I have the following line of code that works fine in Firefox, Chrome and Safari, but not in internet explorer 8. <a href="javascript:void(0);" onclick="showHide('reading','type_r','r');">Show me the example</a> The function simply shows and hides a div on clicking the hyperlink. Is there anything I'm missing here? This is the showHide function: function showHide(elementId,parentId,qtype) { if (document.getElementById && !document.all) { var elementParent = document.getElementById(parentId); var element = document.getElementById(elementId); var upArrowId = 'up-arrow-'+qtype; var downArrowId = 'down-arrow-'+qtype; if(element.style.visibility == 'hidden'){ elementParent.style.height = 'auto'; element.style.visibility = 'visible'; document.getElementById(upArrowId).style.visibility = 'visible'; document.getElementById(downArrowId).style.visibility = 'hidden'; } else if(element.style.visibility == 'visible'){ element.style.visibility = 'hidden'; elementParent.style.height = '50px'; document.getElementById(upArrowId).style.visibility = 'hidden'; document.getElementById(downArrowId).style.visibility = 'visible'; } } } Thanks.

  Read the article

• Multiple Wi-Fi cards and Internet connections on Windows 7

  - by Dpp

  I have two Wi-Fi cards and two separate Internet connections. I connect to the Internet with both of them but one does all of the Internet transactions (and I have not seen any place where I can specify which one I would prefer to use!) What I would like to do is use one of them for the browser and Skype only, and the other one for stock exchange software for instance. Is this is possible?

  Read the article

• [solved] Why can't I dynamically add lines to a HTML table using JavaScript in Internet Explorer?

  - by karlthorwald

  After many hours of debugging I am tired, maybe you can help me now to solve this: In a new Firefox it works, in my Internet Explorer 6 or 7 it doesn't: <html> <head> <script type="text/javascript"> function newLine() { var tdmod = document.createElement('td'); tdmod.appendChild(document.createTextNode("dynamic")); var tr = document.createElement('tr'); tr.appendChild(tdmod); var tt = document.getElementById("t1"); tt.appendChild(tr); } </script> </head> <body> <a href="#" onclick="newLine()">newLine</a> <table id="t1" border="1"> <tr> <td> static </td> </tr> </table> </body> You can klick on the link and new lines should be added to the table. Try it here: http://dl.dropbox.com/u/1508092/iejs.html#

  Read the article

• Unable to share internet by using HOSTEDNETWORK after installing AVAST recently

  - by Shanks

  I was able to share my laptop's internet with my smartphone by using this command "netsh wlan start hostednetwork". But when I installed Avast in my Windows 8 OS, I am able to start the hostednetwork as before and my smartphone also finds the virtual AP but still I can't use internet on the smartphone. It's like the internet sharing has been disabled by the Antivirus. How do I tell Avast that its okay to use the hostednetwork?

  Read the article

• No internet access on Windows 7 - part 2

  - by Vnuk

  This is a continuation of my previous question. The problems started when I turned on my wireless connection for the first time. Since then, every time I boot my Windows 7, my LAN connection does not have internet access. In my previous question, I got a key answer (route delete). Now my procedure to get LAN internet connectivity (local network works fine) when I boot looks like this: Power on WLAN Disconnect LAN cable Power off WLAN Execute route delete 0.0.0.0 if 11 Connect LAN cable Now my LAN connection has internet access. Another behavior that I can't explain - while my LAN connection has no internet access, Network and Sharing center refers to it as Unknown network, with a public icon. When I go through the fore mentioned procedure, it is referred to with my home WLAN network name, with status connected, and the Unknown network disappears.

  Read the article

• Windows Server 2003: Router, DHCP, Looses internet connection

  - by jM2.me

  I have following setup: a windows server 2003 dedicated server with tho nics. One is connected to internet (no modem/router), and second one is connected to private network. Server has DHCP server installed on it and internet nic is being shared for internet access. The problem is sometimes server looses connection to the internet, so same happens to private network. So far I can manually fix it by releasing and renewing IP address. What could be the cause of this problem? DHCP lease from ISP? Thanks

  Read the article

• Windows Server 2003: Router, DHCP, Loses internet connection

  - by jM2.me

  I have following setup: a windows server 2003 dedicated server with tho nics. One is connected to internet (no modem/router), and second one is connected to private network. Server has DHCP server installed on it and internet nic is being shared for internet access. The problem is sometimes server loses connection to the internet, so same happens to private network. So far I can manually fix it by releasing and renewing IP address. What could be the cause of this problem? DHCP lease from ISP? Thanks

  Read the article

• Multiple wifi cards and Internet connections on Win-7

  - by Dpp

  Hello, I have two wifi cards and two separated internet connections. I connect to the Internet with both of them but one does all of the internet transactions (and I have not seen any place where I can specify which one I would prefer to use!) What I would like to do is use one of them for the browser and skype only, and the other one for stock exchange software for instance. Any idea if it is possible?

  Read the article

• How to resolve 'No internet connectivity issues' with a Virtualised 2008 R2 Server using Forefront UAG

  - by user684589

  I have spent some considerable time reading up on as many possible blogs and articles as I can to help me solve why my VM (Running on Hyper-V) for DirectAccess has suddenly stopped being able to access the internet. The VM setup shares the same internet connection on which I have written and submitted this question so I know that the actual underlying internet connection is fully functional. Previous to last week the DirectAccess was fully functional and had no issues. This is a recent problem which was led up to by a number of consistent crashes on the DA machine when access was attempted. Upon reboot all seemed well until recently. I am not certain whether it is relevant, but previously to this I had a number of power issues where the entire VM host shutdown unexpectedly leaving around 8 VM's in a bad way. Upon restart, the UAG DirectAccess machine was unable to access its configuration service (although the service was started) but this seemed to relate to the Light-Weight Active Directory Service AD LDS which had a corrupted database. Having repaired this database, I restarted the service and could subsequently reconnect to the configuration service again. For good measure I re-bound the network adapters (virtualised through Hyper-V) and DirectAccess claimed to be all happy again. However as it stands my machine is still unable to access the internet showing the "No internet connectivity" exclamation mark for the external facing NIC. I have also tried removing the adapters, disabling, re-enabling and the problem persists. The intranet part of the VM CorpNet seems to be fully functional as before and I'm running out of ideas. Any input would be greatly appreciated. I am not an advanced Domain Administrator so please be gentle.

  Read the article

< Previous Page | 53 54 55 56 57 58 59 60 61 62 63 64  | Next Page >