Search Results

Search found 11077 results on 444 pages for 'ip'.

Page 57/444 | < Previous Page | 53 54 55 56 57 58 59 60 61 62 63 64  | Next Page >

• ASA 5540 v8.4(3) vpn to ASA 5505 v8.2(5), tunnel up but I cant ping from 5505 to IP on other side

  - by user223833

  I am having problems pinging from a 5505(remote) to IP 10.160.70.10 in the network behind the 5540(HQ side). 5505 inside IP: 10.56.0.1 Out: 71.43.109.226 5540 Inside: 10.1.0.8 out: 64.129.214.27 I Can ping from 5540 to 5505 inside 10.56.0.1. I also ran ASDM packet tracer in both directions, it is ok from 5540 to 5505, but drops the packet from 5505 to 5540. It gets through the ACL and dies at the NAT. Here is the 5505 config, I am sure it is something simple I am missing. ASA Version 8.2(5) ! hostname ASA-CITYSOUTHDEPOT domain-name rngint.net names ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 10.56.0.1 255.255.0.0 ! interface Vlan2 nameif outside security-level 0 ip address 71.43.109.226 255.255.255.252 ! banner motd ***ASA-CITYSOUTHDEPOT*** banner asdm CITY SOUTH DEPOT ASA5505 ftp mode passive clock timezone EST -5 clock summer-time EDT recurring dns server-group DefaultDNS domain-name rngint.net access-list outside_1_cryptomap extended permit ip host 71.43.109.226 host 10.1.0.125 access-list outside_1_cryptomap extended permit ip 10.56.0.0 255.255.0.0 10.0.0.0 255.0.0.0 access-list outside_1_cryptomap extended permit ip 10.56.0.0 255.255.0.0 10.106.70.0 255.255.255.0 access-list outside_1_cryptomap extended permit ip 10.56.0.0 255.255.0.0 10.106.130.0 255.255.255.0 access-list outside_1_cryptomap extended permit ip host 71.43.109.226 host 10.160.70.10 access-list inside_nat0_outbound extended permit ip host 71.43.109.226 host 10.1.0.125 access-list inside_nat0_outbound extended permit ip 10.56.0.0 255.255.0.0 10.0.0.0 255.0.0.0 access-list inside_nat0_outbound extended permit ip 10.56.0.0 255.255.0.0 10.106.130.0 255.255.255.0 access-list inside_nat0_outbound extended permit ip 10.56.0.0 255.255.0.0 10.106.70.0 255.255.255.0 access-list inside_nat0_outbound extended permit ip host 71.43.109.226 10.106.70.0 255.255.255.0 pager lines 24 logging enable logging buffer-size 25000 logging buffered informational logging asdm warnings mtu inside 1500 mtu outside 1500 icmp unreachable rate-limit 1 burst-size 1 icmp permit any inside no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 route outside 0.0.0.0 0.0.0.0 71.43.109.225 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy aaa-server TACACS+ protocol tacacs+ aaa-server TACACS+ (inside) host 10.106.70.36 key ***** aaa authentication http console LOCAL aaa authentication ssh console LOCAL aaa authorization exec authentication-server http server enable http 192.168.1.0 255.255.255.0 inside http 10.0.0.0 255.0.0.0 inside http 0.0.0.0 0.0.0.0 outside snmp-server host inside 10.106.70.7 community ***** no snmp-server location no snmp-server contact snmp-server community ***** snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto map outside_map 1 match address outside_1_cryptomap crypto map outside_map 1 set pfs group1 crypto map outside_map 1 set peer 64.129.214.27 crypto map outside_map 1 set transform-set ESP-3DES-SHA crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption des hash md5 group 2 lifetime 86400 telnet timeout 5 ssh 10.0.0.0 255.0.0.0 inside ssh 0.0.0.0 0.0.0.0 outside ssh timeout 5 console timeout 0 management-access inside dhcpd auto_config outside ! dhcpd address 10.56.0.100-10.56.0.121 inside dhcpd dns 10.1.0.125 interface inside dhcpd auto_config outside interface inside ! dhcprelay server 10.1.0.125 outside dhcprelay enable inside dhcprelay setroute inside dhcprelay timeout 60 threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept tftp-server inside 10.1.1.25 CITYSOUTHDEPOT-ASA-Confg webvpn tunnel-group 64.129.214.27 type ipsec-l2l tunnel-group 64.129.214.27 ipsec-attributes pre-shared-key ***** ! ! prompt hostname context

  Read the article

• WiFi Access Identification

  - by 100plus

  Is it possible for anyone to detect your IP address or particular location in a given area when you are accessing the Internet using their WiFi?

  Read the article

• Number of subnets for specific mask

  - by kutacz

  Question source Problem: Your company has been assigned the following IP address: 192.112.136.0 /27 Your group has been assigned the fourth subnet. Question 5: How many useable subnets are available for assignment? Why the answer is 6? I would shoot it's 8 , because 255/32 = 8. More generally - what is an correct algorithm to compute the number of available subnetworks for the same mask?

  Read the article

• Postgres - could not create any TCP/IP sockets

  - by Jacka

  I'm running a rails app in development with postgresql 9.3. When I tried to start passenger server today, I got: PG::ConnectionBad - could not connect to server: Connection refused Is the server running on host "localhost" (217.74.65.145) and accepting TCP/IP connections on port 5432? No big deal I thought, that happened before. Restarting postgres always solved the problem. So I ran sudo service postgresql restart and got: * Restarting PostgreSQL 9.3 database server * The PostgreSQL server failed to start. Please check the log output: 2014-06-11 10:32:41 CEST LOG: could not bind IPv4 socket: Cannot assign requested address 2014-06-11 10:32:41 CEST HINT: Is another postmaster already running on port 5432? If not, wait a few seconds and retry. 2014-06-11 10:32:41 CEST WARNING: could not create listen socket for "localhost" 2014-06-11 10:32:41 CEST FATAL: could not create any TCP/IP sockets ...fail! My postgresql.conf points to the defaults: localhost and port 5432. I tried changing the port but the error message is the same (except the port change). Both ps aux | grep postgresql and ps aux | grep postmaster return nothing. EDIT: In postgresql.conf I changed listen_addresses to 127.0.0.1 instead of localhost and it did the trick, server restarted. I also had to edit my applications' db config and point to 127.0.0.1 instead of localhost. However, the question is now, why is localhost considered to be 217.74.65.145 and not 127.0.0.1? That's my /etc/hosts: 127.0.0.1 local 127.0.1.1 jacek-X501A1 127.0.0.1 something.name.non.example.com 127.0.0.1 company.something.name.non.example.com

  Read the article

• Bind ADFS 2.0 service to a specific IP address

  - by ccellar

  I have one server with ADFS-2.0 and a few websites on it. One of the websites is Dynamics CRM which listens on a specific IP address on port 443. Dynamics CRM provides a metadata file for configuration purposes which could be used to configure a relaying party trust with ADFS. It is accessible with the URL https://auth.contoso.com/FederationMetadata/2007-06/federationmetadata.xml The problem is that ADFS-2.0 installs a service which registers following urlacl https://+:443/FederationMetadata/2007-06/ This means the result of accessing the URL https://auth.contoso.com/FederationMetadata/2007-06/federationmetadata.xml is the metadata file of ADFS, not the one of Dynamics CRM. I've tried to delete the default urlacl and added (one of them at a time) https://192.168.1.2:443/FederationMetadata/2007-06/ https://adfs.mydomain.com:443/FederationMetadata/2007-06/ but neither of them worked. Instead the ADFS-service failed to startup complete. Is there any way to bind this service to a IP address? At the moment I see only two alternatives Bind the service to a non standard port. This leads to problems because this means that also the ADFS website has to use a non-standard HTTPS-port. Install ADFS-2.0 on a different server (this is my favorite alternative - however it is not possible in every situation...)

  Read the article

• Mac OS X 10.6 assign mapped IP to Windows 7 VM in Parallels

  - by Alex

  I'm trying to assign a mapped IP address to a Windows 7 VM. I have setup running in Parallels 5 in wireless bridged networking mode. The problem I am having is that it looks like the VM is actually broadcasting the MAC address of the host machine and thus causing a clash of IP addresses on the network. This is my current setup: Macbook Pro :~ ifconfig -a lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 inet6 ::1 prefixlen 128 inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1 inet 127.0.0.1 netmask 0xff000000 gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280 stf0: flags=0<> mtu 1280 en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 ether 00:26:b0:df:31:b4 media: autoselect status: inactive supported media: none autoselect 10baseT/UTP <half-duplex> 10baseT/UTP <full-duplex> 10baseT/UTP <full-duplex,flow-control> 10baseT/UTP <full-duplex,hw-loopback> 100baseTX <half-duplex> 100baseTX <full-duplex> 100baseTX <full-duplex,flow-control> 100baseTX <full-duplex,hw-loopback> 1000baseT <full-duplex> 1000baseT <full-duplex,flow-control> 1000baseT <full-duplex,hw-loopback> fw0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 4078 lladdr 00:26:b0:ff:fe:df:31:b4 media: autoselect <full-duplex> status: inactive supported media: autoselect <full-duplex> en1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 inet6 fe80::226:bbff:fe0a:59a1%en1 prefixlen 64 scopeid 0x6 inet 192.168.1.97 netmask 0xffffff00 broadcast 192.168.1.255 ether 00:26:bb:0a:59:a1 media: autoselect status: active supported media: autoselect vnic0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 inet 192.168.1.81 netmask 0xffffff00 broadcast 192.168.1.255 ether 00:1c:42:00:00:08 media: autoselect status: active supported media: autoselect vnic1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 inet 10.37.129.2 netmask 0xffffff00 broadcast 10.37.129.255 ether 00:1c:42:00:00:09 media: autoselect status: active supported media: autoselect Windows 7: :~ ipconfig -all Windows IP Configuration Host Name . . . . . . . . . . . . : Alex-PC Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Parallels Ethernet Adapter Physical Address. . . . . . . . . : 00-1C-42-B8-E7-B4 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Tunnel adapter Teredo Tunneling Pseudo-Interface: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft Teredo Tunneling Adapter Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Tunnel adapter isatap.{ACAC7EBB-5E5F-4F53-AFD9-E6EAEEA0FEE2}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft ISATAP Adapter #3 Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Billion Bipac 7200 modem router: In DHCP server settings have the following two mapping entries. alex-macbook-win7 00:1c:42:00:00:08 192.168.1.98 alex-macbook 00:26:bb:0a:59:a1 192.168.1.97 The problem I have is that when the VM starts up it gets assigned the 192.168.1.97 address instead of the .98 address and thus networking on the host stops working as it says there is a clash. I have tried removing the mapping for "alex-macbook" which results in the guest machine being assigned a normal DHCP address and NOT the one that is in the mapping of the router.

  Read the article

• Can ping IP address and nslookup hostname but cannot ping hostname

  - by Puddingfox

  I have a DNS server set up on one of my machines using BIND 9.7 Everything works fine with it. On my Windows 7 desktop, I have statically-assigned all network values. I have one DNS server set -- my DNS server. On my desktop, I can ping a third machine by IP fine. I can nslookup the hostname of the third machine fine. When I ping the hostname, it says it cannot find the host. / C:\Users\James>nslookup icecream Server: cake.my.domain Address: xxx.xxx.6.3 Name: icecream.my.domain Address: xxx.xxx.6.9 C:\Users\James>ping xxx.xxx.6.9 Pinging xxx.xxx.6.9 with 32 bytes of data: Reply from xxx.xxx.6.9: bytes=32 time<1ms TTL=255 Reply from xxx.xxx.6.9: bytes=32 time<1ms TTL=255 Reply from xxx.xxx.6.9: bytes=32 time<1ms TTL=255 Reply from xxx.xxx.6.9: bytes=32 time<1ms TTL=255 Ping statistics for xxx.xxx.6.9: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms C:\Users\James>ping icecream Ping request could not find host icecream. Please check the name and try again. I have also specified the search domain as my.domain xxx.xxx and my.domain substituted for security Why can I not ping by hostname? I also can not ping using the FQDN. The problem is that this problem is shared by all applications that resolve hostnames. I cannot use PuTTY to SSH to my machines by hostname; only by IP

  Read the article

• Can ping IP address and nslookup hostname but cannot ping hostname

  - by jao

  On a windows 2003 server I can nslookup www.google.com which returns Server: localhost Address: 127.0.0.1 Non-authoritative answer: Name: www.l.google.com Addresses: 74.125.79.104, 74.125.79.147, 74.125.79.99 Aliases: www.google.com I can then ping 74.125.79.104: Pinging 74.125.79.104 with 32 bytes of data: Reply from 74.125.79.104: bytes=32 time=16ms TTL=54 Reply from 74.125.79.104: bytes=32 time=32ms TTL=54 Reply from 74.125.79.104: bytes=32 time=15ms TTL=54 Reply from 74.125.79.104: bytes=32 time=15ms TTL=54 Ping statistics for 74.125.79.104: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 15ms, Maximum = 32ms, Average = 19ms But I cannot ping www.google.com: Ping request could not find host www.google.com. Please check the name and try again. (this one is different from the other question in that this one has a TLD, it is not a local domain.) Update: I am running a dns server at localhost (127.0.0.1). Even when I change it to use for example opendns, it still can nslookup hostname and ping ip address, but not ping hostname. So what is wrong? Update 2: here is the ipconfig /all result: Windows IP Configuration Host Name . . . . . . . . . . . . : SERVER Primary Dns Suffix . . . . . . . : NETWORK.local Node Type . . . . . . . . . . . . : Unknown IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : NETWORK.local Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet #2 Physical Address. . . . . . . . . : 00-0F-1F-56-3B-AA DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.7.2 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.7.1 DNS Servers . . . . . . . . . . . : 127.0.0.1 Update 3: Thanks everyone for their help and suggestions. I appreciate that. Ipconfig /flushdns returns: Sucessfully flushed the DNS resolver cache Ipconfig /displaydns returns: 2.7.168.192.in-addr.arpa ---------------------------------------- Record Name . . . . . : 2.7.168.192.in-addr.arpa. Record Type . . . . . : 12 Time To Live . . . . : 0 Data Length . . . . . : 4 Section . . . . . . . : Answer PTR Record . . . . . : webserver.mydomainname.com 1.0.0.127.in-addr.arpa ---------------------------------------- Record Name . . . . . : 1.0.0.127.in-addr.arpa. Record Type . . . . . : 12 Time To Live . . . . : 0 Data Length . . . . . : 4 Section . . . . . . . : Answer PTR Record . . . . . : localhost Update 4: Wireshark shows the following: 3 11.540542 208.67.220.220 192.168.7.2 DNS Standard query response A 74.125.79.99 A 74.125.79.104 A 74.125.79.147 6 42.056794 192.168.7.2 192.168.7.255 NBNS Name query NB WWW.GOOGLE.COM<00> which is weird: when I ping, it sends a packet to 192.168.7.255 instead of asking the DNS server for an address

  Read the article

• ipvsadm lists a few hosts by IP only, rest by name

  - by dmourati

  We use keepalived to manage our Linux Virtual Server (LVS) load balancer. The LVS VIPs are setup to use a FWMARK as configured in iptables. virtual_server fwmark 300000 { delay_loop 10 lb_algo wrr lb_kind NAT persistence_timeout 180 protocol TCP real_server 10.10.35.31 { weight 24 MISC_CHECK { misc_path "/usr/local/sbin/check_php_wrapper.sh 10.10.35.31" misc_timeout 30 } } real_server 10.10.35.32 { weight 24 MISC_CHECK { misc_path "/usr/local/sbin/check_php_wrapper.sh 10.10.35.32" misc_timeout 30 } } real_server 10.10.35.33 { weight 24 MISC_CHECK { misc_path "/usr/local/sbin/check_php_wrapper.sh 10.10.35.33" misc_timeout 30 } } real_server 10.10.35.34 { weight 24 MISC_CHECK { misc_path "/usr/local/sbin/check_php_wrapper.sh 10.10.35.34" misc_timeout 30 } } } http://www.austintek.com/LVS/LVS-HOWTO/HOWTO/LVS-HOWTO.fwmark.html [root@lb1 ~]# iptables -L -n -v -t mangle Chain PREROUTING (policy ACCEPT 182G packets, 114T bytes) 190M 167G MARK tcp -- * * 0.0.0.0/0 w1.x1.y1.4 multiport dports 80,443 MARK set 0x493e0 62M 58G MARK tcp -- * * 0.0.0.0/0 w1.x1.y2.4 multiport dports 80,443 MARK set 0x493e0 [root@lb1 ~]# ipvsadm -L IP Virtual Server version 1.2.1 (size=4096) Prot LocalAddress:Port Scheduler Flags -> RemoteAddress:Port Forward Weight ActiveConn InActConn FWM 300000 wrr persistent 180 -> 10.10.35.31:0 Masq 24 1 0 -> dis2.domain.com:0 Masq 24 3 231 -> 10.10.35.33:0 Masq 24 0 208 -> 10.10.35.34:0 Masq 24 0 0 At the time the realservers were setup, there was a misconfigured dns for some hosts in the 10.10.35.0/24 network. Thereafter, we fixed the DNS. However, the hosts continue to show up as only their IP numbers (10.10.35.31,10.10.35.33,10.10.35.34) above. [root@lb1 ~]# host 10.10.35.31 31.35.10.10.in-addr.arpa domain name pointer dis1.domain.com. OS is CentOS 6.3. Ipvsadm is ipvsadm-1.25-10.el6.x86_64. kernel is kernel-2.6.32-71.el6.x86_64. Keepalived is keepalived-1.2.7-1.el6.x86_64. How can we get ipvsadm -L to list all realservers by their proper hostnames?

  Read the article

• Changing externally visible IP on a multi-IP router?

  - by AlternateZ

  I work at a public library and I'm trying to configure OCLC's EzProxy software. I've run into a problem and I think it's related to our network config. I'm punching above my weight here a little so I need some help. I think I'm trying to configure a 1:1 NAT, but not sure how or if our hardware supports it. The EzProxy machine is on an internet line which supports multiple external IPs. Our router is a Billion BiGuard30. There's another server on this line, let's say its IP is x.x.x.9. The EzProxy machine is x.x.x.11 I've set up port forwarding from x.x.x.11 on the http ports to the EzProxy machine. Trying to browse to x.x.x.11 from an external PC works fine - we get to the EzProxy page we are serving. However, if we go to something like WhatIsMyIP from the EzProxy machine, it says that its IP is x.x.x.9. This causes problems with our user authentication software. How do we make the rest of the internet see that the machine is x.x.x.11? There doesnt seem to be any "outbound port forwarding" on the Billion router, nor is there any "1:1 NAT" options in its config webpage. The EzProxy machine is running Ubuntu 12.04, if that helps.

  Read the article

• Distribute IP packets accross different NIC queues with MSI (Message Signalled Interrupts)

  - by Ansis Atteka

  NetXtreme II BCM5709 Gigabit Ethernet NIC supports MSI feature (Message Signaled Interrupts) and it has 8 queues. Each queue has its own Interrupt handler in /proc/interrupts. What I am trying to accomplish is to tell NIC which packets should go to which queue. Questions: Is it possible to manually specify which IP packets should go to which queue by encapsulated protocol type (e.g. IPsec packets go in one queue, while TCP packets go in another queue)? If it is possible - how can I do it under Linux? If it is not possible - should I look at MSI-X capable NIC cards to solve this problem? More details: We have one Interface that is terminating IPSec and forwarding/terminating TCP connections. The IPSec packet decryption is inlined (this means that decryption is done under the same ksoftirqd/X context). We are trying to find out if we will be able to improve total performance if IPSec packets will be scheduled on another CPU than TCP packets. One more limitation is that IPSec code is not MP-safe, hence I can not run it under more than one ksoftirqd/X. By default it seems that packets are distributed/hashed by source IP over the 8 NIC queues. The bottleneck is IPSec that chokes out TCP traffic while it is decrypting/encrypting IPSec packets at ~100% CPU. OS is Ubuntu 10.10 (2.6.32-27-server) and NIC is Broadcom BCM5709.

  Read the article

• IIS8 behind a VPN + Windows Server 2012 - how to properly bind IP+Port

  - by ryugen

  This is my first question so I hope I'm going to give you enough information. I'm running Windows Server 2012 within the Hyper-V environment of my Windows 8 machine. Within Windows Server 2012 I'm running a VPN tool based on openVPN to hide my real IP. When I run IIS8 with the VPN disconnected it works flawlessly through the Internet (port 80 forwarded correctly). But as soon as I connect to the VPN I can't reach my site through the domain anymore. Now I tried basically everything I know which is why I'm asking you guys. I tried binding IIS8 to the IP of my virtual ethernet card. I tried changing the priority of the NIC through the "Network and sharing center" via the advanced tab. I used ipconfig /flushdns in case there was something wrong in the DNS handling. Hell, I even turned off the Windows firewall. I also used a port scanner to verify the problem. The webserver is reachable on port 80 with VPN disconnected and immediately gets unreachable on connect. Theoretically both IPs (my regular one AND the VPN) should be reachable or at least not impair the other one right? Do you have any other suggestion? Do I have to route something somewhere somehow?

  Read the article

• Apache 403 Forbidden Error when accessing local web server using local IP address

  - by amjo324

  I have an odd problem when attempting to browse to pages stored on a local web server (Apache 2.2). The pages are served as expected when I browse to localhost or 127.0.0.1 on port 80. Yet when I attempt to browse to the same pages by referencing the local IP address (192.168.x.x), I receive a HTTP 403 (Forbidden) error. In essence, http://localhost:80 works but 192.168.x.x:80 doesn't even though I'm specifying the IP of the local machine. You may be thinking "who cares? just use localhost". However, this is the first step in troubleshooting why I cannot remotely access these pages from different hosts on my LAN. I'm presuming this can't be a firewall issue as I'm only connecting to the local machine. Even so, I verified there was no iptables rules that could be having an effect. I've checked the Apache error logs and the corresponding line of relevance is: [Sat Oct 19 07:38:35 2013] [error] [client 192.168.x.x] client denied by server configuration: /var/www/ I've inspected most of the apache config files and they don't appear to differ from what you would expect with a default install. I can't see anything in apache2.conf that would be a problem and httpd.conf is an empty file. This is an excerpt from /etc/apache2/sites-enabled/000-default: <VirtualHost *:80> ServerAdmin webmaster@localhost DocumentRoot /var/www <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/> Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> Any insight as to where I can look next to find a solution ? Thanks in advance.

  Read the article

• VPN - local and remote networks IP collision

  - by Guido García

  I have created a VPN connection in Windows using the New Network Connection wizard that comes with Windows. It works without problems in most places, but there is one concrete place where, despite the connection to the remote public IP works fine, it is not able to validate the login/password and establish the VPN connection. In this place, the network is 10.0.0.x (the same I use in other places where I am able to connect). The remote network is 192.168.x.x, so I suspect there is some kind of IP collision, because before connecting, a traceroute to i.e. 192.168.0.40 does not fail. 1 4 ms 1 ms 1 ms LINKSYS [10.0.0.1] 2 5 ms 1 ms 1 ms 172.26.27.1 3 4 ms 5 ms 3 ms 192.168.1.100 ... (more) I can't modify the local network further than the first router (10.0.0.1). That is the only different I've found so far. Any idea about how to solve it? Thank you.

  Read the article

• Kickstart CentOS 6 prompting for TCP/IP with network set to DHCP

  - by Andy Shinn

  I am trying to stop my kickstart CentOS install prompting me for TCP/IP information. After I click through this prompt (keeping IPv4 and IPv6 to their defaults) the installation continues and completes just fine. Below is my kickstart file: # Andy's super awesome VM kickstart file install url --url=http://mirrors.kernel.org/centos/6/os/x86_64 lang en_US.UTF-8 keyboard us text %include /tmp/network.ks rootpw --iscrypted $6$RA8DyrNTsVJkGIgY$ohZ62HHiOjNnn1yDMZlIu3lQ63D3plGPcbVZtPKE8Oq6Z.IGUgN.kNLkxs/ZymZuluRDWsW2eey5zLOl2G3mp. firewall --service=ssh authconfig --enableshadow --passalgo=sha512 selinux --disabled timezone America/Los_Angeles bootloader --location=mbr --driveorder=vda --append="crashkernel=auto rhgb quiet" # The following is the partition information you requested # Note that any partitions you deleted are not expressed # here so unless you clear all partitions first, this is # not guaranteed to work zerombr clearpart --all --drives=vda --initlabel part /boot --fstype=ext4 --size=500 part pv.253002 --grow --size=1 volgroup vg1 --pesize=4096 pv.253002 logvol / --fstype=ext4 --name=lv_root --vgname=vg1 --grow --size=1024 --maxsize=51200 logvol swap --name=lv_swap --vgname=vg1 --grow --size=4032 --maxsize=4032 repo --name="CentOS" --baseurl=http://mirrors.kernel.org/centos/6/os/x86_64 --cost=100 repo --name="Puppet Labs Products" --baseurl=http://yum.puppetlabs.com/el/6/products/x86_64 repo --name="Puppet Labs Dependencies" --baseurl=http://yum.puppetlabs.com/el/6/dependencies/x86_64 repo --name="EyeFi" --baseurl=http://flexo.eye.fi/6/eye-fi-api %packages @core @server-policy puppet facter %end %pre --erroronfail #!/bin/bash for x in `cat /proc/cmdline`; do case $x in SERVERNAME*) eval $x echo "network --onboot yes --device eth0 --bootproto dhcp --hostname ${SERVERNAME}.eye.fi" /tmp/network.ks ;; esac; done %end %post puppet agent --waitforcert 10 --onetime --no-daemon --pluginsync --server puppet.eye.fi %end reboot My kernel arguments are in this following virt-install command that I use to start the install: virt-install -n zabbix -r 2048 --vcpus=2 -l http://mirrors.kernel.org/centos/6/os/x86_64 --disk /dev/vg_inf1/zabbix --network bridge=br85 --initrd-inject=/home/ashinn/vm_kickstart --extra-args "ks=file:/vm_kickstart SERVERNAME=zabbix" --autostart During the install, I can pull up a console on the second terminal and verify the contents of /tmp/network.ks are: network --onboot=yes --bootproto=dhcp --ipv6=auto --hostname=jenkins2.mydomain.com Why might Anaconda be prompting for the TCP/IP settings when they are already set to DHCP?

  Read the article

• Blocking an IP from connecting

  - by Sam W.

  I have a problem with my Apache webserver where there's and IP than connecting to my server, using alot of connection and wont die which eventually making my webserver timeout. The connection will stay as SYN_SENT state if I check using netstat -netapu I even flush my iptables and use the basic rules and it still doesn't work. The IP will get connected when I start my Apache Basic rules that I use: iptables -A INPUT -i lo -j ACCEPT iptables -A INPUT ! -i lo -d 127.0.0.0/8 -j REJECT iptables -A INPUT -s 89.149.244.117 -j REJECT iptables -A OUTPUT -s 89.149.244.117 -j REJECT iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A OUTPUT -j ACCEPT iptables -A INPUT -p tcp --dport 80 -j ACCEPT iptables -A INPUT -p tcp --dport 443 -j ACCEPT iptables -A INPUT -p tcp --dport 21 -j ACCEPT iptables -A INPUT -p icmp -m icmp --icmp-type 8 -j ACCEPT iptables -A INPUT -j REJECT iptables -A FORWARD -j REJECT The bold part is rule in question. Not sure this is related but tcp_syncookies value is 1. Can someone point out my mistake? Is there a way to block it for good. Thank you

  Read the article

• kvm-over-ip, multiple machines per cable run

  - by Sirex

  I'm looking at getting a kvm-over-ip setup for a server room. Typically these devices have 16 or so cat5 leads that come out of them and then a convertor that converts each cat5 into a vga & ps2 pair. Can you run one cable from the unit into a switch, and then leads from the switch into each machine ? I have several machines on the other side of the server room that i'd like to have avaliable but i dont want to run 16 cables to them. I'm thinking this should be possible being IP layer and all, but as each device normally has its own cable out the back of the kvm unit i'm not certain. Perhaps the kvm's rear ports act essentially like a switch anyway in which case it should work, or perhaps if i run all 16 cables into a seperate switch right next to it and aggregate the ports together, run one cable to a switch on the other side of the room with similar number of ports agregated together, then use that switch to plug each macine into ? I'm fairly sure this is possible, but i just want to check before i shell out the cash as i've never tried it.

  Read the article

• IP tables blocking access to most hosts but some accesses being logged

  - by epo

  What am I getting wrong? A while back I locked down my web hosting service while hardening it or at least trying to. Apache listens on port 80 only and I set up iptables using the following: IPS="list of IPs" iptables --new-chain webtest # Accept all established connections iptables -A INPUT --protocol tcp --dport 80 --jump webtest iptables -A INPUT --match state --state ESTABLISHED,RELATED --jump ACCEPT iptables -A webtest --match state --state ESTABLISHED,RELATED --jump ACCEPT for ip in $IPS; do iptables -A webtest --match state --state NEW --source $ip --jump ACCEPT done iptables -A webtest --jump DROP However looking at my apache logs I notice various log entries in access_log, e.g. 221.192.199.35 - - [16/May/2010:13:04:31 +0100] "GET http://www.wantsfly.com/prx2.php?hash=926DE27C156B40E55E4CFC8F005053E2D81E6D688AF0 HTTP/1.0" 404 206 "-" "Mozilla/ 4.0 (compatible; MSIE 6.0; Windows NT 5.0)" 201.228.144.124 - - [16/May/2010:11:54:16 +0100] "GET /w00tw00t.at.ISC.SANS.DFind:) HTTP/1.1" 400 226 "-" "-" 207.46.195.224 - - [16/May/2010:04:06:48 +0100] "GET /robots.txt HTTP/1.1" 200 311 "-" "msnbot/2.0b (+http://search.msn.com/msnbot.htm)" How are these slipping through? I don't mind the indexing bots (though I am a little surprised to see them get through). I suppose they must be getting through using the ESTABLISHED,RELATED rules. And no, I can't for the life of me remember why the first match state rule is there So 2 questions: is there a better way to set up iptables to restrict access to specified hosts? How exactly are these 3 examples slipping through?

  Read the article

• Two servers, two domains, one ip. mod_proxy beginner

  - by Gutsav

  I run two virtual web servers (both running apache2 on debian). I have just one external IP, but two domains, and I want a domain going to each of the servers. I've understood that I need a Reverse Proxy, and I enabled both the mod_proxy and the mod_proxy_http modules on the "primary server". Do I need to enable anything on the "secondary server"? I also understood that I need to write some things in a virtual host file, but what? On the primary server, I have a virtual host file for one of the domains, and some for subdomains. I want domain1.tld to go to the primary server (port 80 is forwarded to it, so that works) and domain2.tld to go to the other server (internal ip 192.168.0.x). No ports needs to be forwarded to it, right? So, what to add and in which virtual host file? Or a new one? Other questions suggest adding ProxyPass and ProxyPassReverse, but I'm lost anyway, and I just don't understand the apache documentation. Thanks in advance

  Read the article

• IP address numbers in MySQL subquery

  - by Iain Collins

  I have a problem with a subquery involving IPV4 addresses stored in MySQL (MySQL 5.0). The IP addresses are stored in two tables, both in network number format - e.g. the format output by MySQL's INET_ATON(). The first table ('events') contains lots of rows with IP addresses associated with them, the second table ('network_providers') contains a list of provider information for given netblocks. events table (~4,000,000 rows): event_id (int) event_name (varchar) ip_address (unsigned 4 byte int) network_providers table (~60,000 rows): ip_start (unsigned 4 byte int) ip_end (unsigned 4 byte int) provider_name (varchar) Simplified for the purposes of the problem I'm having, the goal is to create an export along the lines of: event_id,event_name,ip_address,provider_name If do a query along the lines of either of the following, I get the result I expect: SELECT provider_name FROM network_providers WHERE INET_ATON('192.168.0.1') >= network_providers.ip_start ORDER BY network_providers.ip_start DESC LIMIT 1 SELECT provider_name FROM network_providers WHERE 3232235521 >= network_providers.ip_start ORDER BY network_providers.ip_start DESC LIMIT 1 That is to say, it returns the correct provider_name for whatever IP I look up (of course I'm not really using 192.168.0.1 in my queries). However, when performing this same query as a subquery, in the following manner, it doesn't yield the result I would expect: SELECT event.id, event.event_name, (SELECT provider_name FROM network_providers WHERE event.ip_address >= network_providers.ip_start ORDER BY network_providers.ip_start DESC LIMIT 1) as provider FROM events Instead the a different (incorrect) value for network_provider is returned - over 90% (but curiously not all) values returned in the provider column contain the wrong provider information for that IP. Using event.ip_address in a subquery just to echo out the value confirms it contains the value I'd expect and that the subquery can parse it. Replacing event.ip_address with an actual network number also works, just using it dynamically in the subquery in this manner that doesn't work for me. I suspect the problem is there is something fundamental and important about subqueries in MySQL that I don't get. I've worked with IP addresses like this in MySQL quite a bit before, but haven't previously done lookups for them using a subquery. The question: I'd really appreciate an example of how I could get the output I want, and if someone here knows, some enlightenment as to why what I'm doing doesn't work so I can avoid making this mistake again. Notes: The actual real-world usage I'm trying to do is considerably more complicated (involving joining two or three tables). This is a simplified version, to avoid overly complicating the question. Additionally, I know I'm not using a between on ip_start & ip_end - that's intentional (the DB's can be out of date, and such cases the owner in the DB is almost always in the next specified range and 'best guess' is fine in this context) however I'm grateful for any suggestions for improvement that relate to the question. Efficiency is always nice, but in this case absolutely not essential - any help appreciated.

  Read the article

• VPN - local and remote networks IP collision

  - by Guido García

  I have created a VPN connection in Windows using the New Network Connection wizard that comes with Windows. It works without problems in most places, but there is one concrete place where, despite the connection to the remote public IP works fine, it is not able to validate the login/password and establish the VPN connection. In this place, the network is 10.0.0.x (the same I use in other places where I am able to connect). The remote network is 192.168.x.x, so I suspect there is some kind of IP collision, because before connecting, a traceroute to i.e. 192.168.0.40 does not fail. 1 4 ms 1 ms 1 ms LINKSYS [10.0.0.1] 2 5 ms 1 ms 1 ms 172.26.27.1 3 4 ms 5 ms 3 ms 192.168.1.100 ... (more) I can't modify the local network further than the first router (10.0.0.1). That is the only different I've found so far. Any idea about how to solve it? Thank you.

  Read the article

• IP tables blocking access to most hosts but some accesses being logged

  - by epo

  What am I getting wrong? A while back I locked down my web hosting service while hardening it or at least trying to. Apache listens on port 80 only and I set up iptables using the following: IPS="list of IPs" iptables --new-chain webtest # Accept all established connections iptables -A INPUT --protocol tcp --dport 80 --jump webtest iptables -A INPUT --match state --state ESTABLISHED,RELATED --jump ACCEPT iptables -A webtest --match state --state ESTABLISHED,RELATED --jump ACCEPT for ip in $IPS; do iptables -A webtest --match state --state NEW --source $ip --jump ACCEPT done iptables -A webtest --jump DROP However looking at my apache logs I notice various log entries in access_log, e.g. 221.192.199.35 - - [16/May/2010:13:04:31 +0100] "GET http://www.wantsfly.com/prx2.php?hash=926DE27C156B40E55E4CFC8F005053E2D81E6D688AF0 HTTP/1.0" 404 206 "-" "Mozilla/ 4.0 (compatible; MSIE 6.0; Windows NT 5.0)" 201.228.144.124 - - [16/May/2010:11:54:16 +0100] "GET /w00tw00t.at.ISC.SANS.DFind:) HTTP/1.1" 400 226 "-" "-" 207.46.195.224 - - [16/May/2010:04:06:48 +0100] "GET /robots.txt HTTP/1.1" 200 311 "-" "msnbot/2.0b (+http://search.msn.com/msnbot.htm)" How are these slipping through? I don't mind the indexing bots (though I am a little surprised to see them get through). I suppose they must be getting through using the ESTABLISHED,RELATED rules. And no, I can't for the life of me remember why the first match state rule is there So 2 questions: is there a better way to set up iptables to restrict access to specified hosts? How exactly are these 3 examples slipping through?

  Read the article

• IPTABLE & IP-routed netwok solution for HOST net and VM's subnet

  - by Daniel

  I've got ProxmoxVE2.1 ruled KVM node on Debian and bunch of VM's guests machine. That is how my networking looks like: # network interface settings auto lo iface lo inet loopback # device: eth0 auto eth0 iface eth0 inet static address 175.219.59.209 gateway 175.219.59.193 netmask 255.255.255.224 post-up echo 1 > /proc/sys/net/ipv4/conf/eth0/proxy_arp And I've got two working subnet solution auto vmbr0 iface vmbr0 inet static address 10.10.0.1 netmask 255.255.0.0 bridge_ports none bridge_stp off bridge_fd 0 post-up ip route add 10.10.0.1/24 dev vmbr0 This way I can reach internet, to resolve outside hosts, update and download everything I need but can't reach one guest VM out of any other VM's inside my network. The second solution allows me to communicate between VM's: auto vmbr1 iface vmbr1 inet static address 10.10.0.1 netmask 255.255.255.0 bridge_ports none bridge_stp off bridge_fd 0 post-up echo 1 > /proc/sys/net/ipv4/ip_forward post-up iptables -t nat -A POSTROUTING -s '10.10.0.0/24' -o vmbr1 -j MASQUERADE post-down iptables -t nat -D POSTROUTING -s '10.10.0.0/24' -o vmbr1 -j MASQUERADE I can even NAT internal addresses: -t nat -I PREROUTING -p tcp --dport 789 -j DNAT --to-destination 10.10.0.220:345 My inexperienced mind is ready to double VM's net adapters: one for the first solution and another - for second (with slightly different adresses) but I'm pretty sure that it's a dumb way to resolve the problem and everything can be resolved via iptables/ip route rules that I can't create. I've tried a dozen of "wizard manuals" and "howto's" to mix both solution but without success. Looking for an advice (and good reading links for networking begginers).

  Read the article

• Linux port-based routing using iptables/ip route

  - by user42055

  I have the following setup: 192.168.0.4 192.168.0.6 192.168.0.1 +-----------+ +---------+ +----------+ |WORKSTATION|------| LINUX |------| GATEWAY | +-----------+ +---------+ +----------+ 192.168.150.10 | 192.168.150.9 +---------+ | VPN | +---------+ 192.168.150.1 WORKSTATION has a default route of 192.168.0.6 LINUX has a default route of 192.168.0.1 I am trying to use the gateway as the default route, but route port 80 traffic via the VPN. Based on what I read at http://www.linuxhorizon.ro/iproute2.html I have tried this: echo "1 VPN" >> /etc/iproute2/rt_tables sysctl net.ipv4.conf.eth0.rp_filter = 0 sysctl net.ipv4.conf.tun0.rp_filter = 0 sysctl net.ipv4.conf.all.rp_filter = 0 iptables -A PREROUTING -t mangle -i eth0 -p tcp --dport 80 -j MARK --set-mark 0x1 ip route add default via 192.168.150.9 dev tun0 table VPN ip rule add from all fwmark 0x1 table VPN When I run "tcpdump -i eth0 port 80" on LINUX, and open a webpage on WORKSTATION, I don't see the traffic go through LINUX at all. When I run a ping from WORKSTATION, I get this back from some packets: 92 bytes from 192.168.0.6: Redirect Host(New addr: 192.168.0.1) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 de91 0 0000 3f 01 4ed3 192.168.0.4 139.134.2.18 Is this why my routing is not working ? Do I need to put GATEWAY and LINUX on different subnets to prevent WORKSTATION being redirected to GATEWAY ? Do I need to use NAT at all, or can I do this with routing alone (which is what I want) ?

  Read the article

• Find routers IP address on the other side

  - by corsiKa

  Here's the basic setup of my network In this diagram: 1: The internet c: cable 2: Wireless router w: wireless connection 3: A win7 box with internet connection sharing enabled 4: A wireless router, but I'm only using its LAN capabilities to connect box 5 to the internet. 5: A win7 box, the computer I'm using to make this post. So its internet works just fine. Now if I'm on box 5, and I ping 192.168.1.1, I hit 4. If I'm on box 3 and I ping 192.168.1.1, I hit 2. Now obviously box 3 does not think 4's IP address is 192.168.1.1, or I wouldn't be able to connect to the internet. Okay, now that you know as much as I do about my network, here's my question: If I was on box 3, how would I determine the IP address of 4? Basically I'm running a webserver on box 5 and want to access this webserver on box 3 and other boxes. So that's the end goal. If there's other information there that can help, I'd appreciate it. Thanks!

  Read the article

< Previous Page | 53 54 55 56 57 58 59 60 61 62 63 64  | Next Page >