Search Results

Search found 14924 results on 597 pages for 'kernel mode'.

Page 57/597 | < Previous Page | 53 54 55 56 57 58 59 60 61 62 63 64  | Next Page >

• PC to USB transfer slow

  - by Vipin Ms

  I'm having trouble with USB transfer,not with external hard disk. Transfer starts with like, for the transfer of 700MB file it starts with 30mb/s and towards the end it stops at 0s and stays put for like 3-4 mins to transfer the last bit. I have tried different USB devices, but no luck. Is it a bug? Another important point is, in Kubuntu there is no such issue. So is it something related to Gnome? I'm using Ubuntu 11.10 64bit. Somebody please help, it's really annoying. Here are the details. PC all of my drives are in ext4. USB I tried ext3,ntfs and fat32. All having the same problem. Here are my USB controllers details: root@LAB:~# lspci|grep USB 00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) Here is an example of one transfer. I connected one of my 4GB usb device. Nov 24 12:01:25 LAB kernel: [ 1175.082175] userif-2: sent link up event. Nov 24 12:01:25 LAB kernel: [ 1695.684158] usb 2-2: new high speed USB device number 3 using ehci_hcd Nov 24 12:01:25 LAB mtp-probe: checking bus 2, device 3: "/sys/devices/pci0000:00/0000:00:1d.7/usb2/2-2" Nov 24 12:01:26 LAB mtp-probe: bus: 2, device: 3 was not an MTP device Nov 24 12:01:26 LAB kernel: [ 1696.132680] usbcore: registered new interface driver uas Nov 24 12:01:26 LAB kernel: [ 1696.142528] Initializing USB Mass Storage driver... Nov 24 12:01:26 LAB kernel: [ 1696.142919] scsi4 : usb-storage 2-2:1.0 Nov 24 12:01:26 LAB kernel: [ 1696.143146] usbcore: registered new interface driver usb-storage Nov 24 12:01:26 LAB kernel: [ 1696.143150] USB Mass Storage support registered. Nov 24 12:01:27 LAB kernel: [ 1697.141657] scsi 4:0:0:0: Direct-Access SanDisk U3 Cruzer Micro 8.02 PQ: 0 ANSI: 0 CCS Nov 24 12:01:27 LAB kernel: [ 1697.168827] sd 4:0:0:0: Attached scsi generic sg2 type 0 Nov 24 12:01:27 LAB kernel: [ 1697.169262] sd 4:0:0:0: [sdb] 7856127 512-byte logical blocks: (4.02 GB/3.74 GiB) Nov 24 12:01:27 LAB kernel: [ 1697.169762] sd 4:0:0:0: [sdb] Write Protect is off Nov 24 12:01:27 LAB kernel: [ 1697.169767] sd 4:0:0:0: [sdb] Mode Sense: 45 00 00 08 Nov 24 12:01:27 LAB kernel: [ 1697.171386] sd 4:0:0:0: [sdb] No Caching mode page present Nov 24 12:01:27 LAB kernel: [ 1697.171391] sd 4:0:0:0: [sdb] Assuming drive cache: write through Nov 24 12:01:27 LAB kernel: [ 1697.173503] sd 4:0:0:0: [sdb] No Caching mode page present Nov 24 12:01:27 LAB kernel: [ 1697.173510] sd 4:0:0:0: [sdb] Assuming drive cache: write through Nov 24 12:01:27 LAB kernel: [ 1697.175337] sdb: sdb1 After that I initiated one transfer. lsof -p 3575|tail -2 mv 3575 root 3r REG 8,8 1719599104 4325379 /media/Misc/The Tree of Life (2011) DVDRip XviD-MAXSPEED/The Tree of Life (2011) DVDRip XviD-MAXSPEED www.torentz.3xforum.ro.avi mv 3575 root 4w REG 8,17 1046347776 15 /media/SREE/The Tree of Life (2011) DVDRip XviD-MAXSPEED/The Tree of Life (2011) DVDRip XviD-MAXSPEED www.torentz.3xforum.ro.avi Here are the total time spent on that transfer. root@LAB:/media/SREE# time mv /media/Misc/The\ Tree\ of\ Life\ \(2011\)\ DVDRip\ XviD-MAXSPEED/ /media/SREE/ real 11m49.334s user 0m0.008s sys 0m5.260s root@LAB:/media/SREE# df -T|tail -2 /dev/sdb1 vfat 3918344 1679308 2239036 43% /media/SREE /dev/sda8 ext4 110110576 60096904 50013672 55% /media/Misc Do you think this is normal?? Approximately 12 minutes for 1.6Gb transfer? Thanks.

  Read the article

• How do I set up nvidia graphics adapter to put out 1080p, it seems to be using interlace mode>

  - by keepitsimpleengineer

  After upgrading to 12.04, my mythbuntu client/server seems to be running in 1080i, the clue comes from: [ 1176.117] (II) NVIDIA(0): Setting mode "1920x1080_60i" [ 1231.340] (II) NVIDIA(0): Setting mode "DFP-1:1920x1080_60@1920x1080+0+0" This is from Xorg.0.log. This whole thing started from video tearing when watching Mythtv recordings. It didn't happen in 10.10. Should I use "TVStandard" "HD1080p" in the screen section since this is a dedicated HTPC? It only connects to an HDTV (1080p) via hdmi. Here is the current xorg.conf file: # nvidia-settings: X configuration file generated by nvidia-settings # nvidia-settings: version 270.29 (buildd@allspice) Fri Feb 25 14:42:07 UTC 2011 Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" 0 0 # commented out by update-manager, HAL is now used and auto-detects devices # Keyboard settings are now read from /etc/default/console-setup # InputDevice "Keyboard0" "CoreKeyboard" # commented out by update-manager, HAL is now used and auto-detects devices # Keyboard settings are now read from /etc/default/console-setup # InputDevice "Mouse0" "CorePointer" Option "Xinerama" "0" EndSection Section "Files" FontPath "unix/:7100" EndSection # commented out by update-manager, HAL is now used and auto-detects devices # Keyboard settings are now read from /etc/default/console-setup #Section "InputDevice" # # generated from default # Identifier "Mouse0" # Driver "mouse" # Option "Protocol" "auto" # Option "Device" "/dev/psaux" # Option "Emulate3Buttons" "no" # Option "ZAxisMapping" "4 5" #EndSection # commented out by update-manager, HAL is now used and auto-detects devices # Keyboard settings are now read from /etc/default/console-setup #Section "InputDevice" # # generated from default # Identifier "Keyboard0" # Driver "kbd" #EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor0" VendorName "Unknown" ModelName "SAMSUNG" HorizSync 26.0 - 81.0 VertRefresh 24.0 - 75.0 Option "DPMS" EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce GT 240" Option "TripleBuffer" "1" EndSection Section "Screen" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "TwinView" "0" Option "metamodes" "DFP: nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection After a little digging, the question changes slightly, to wit... Per Chapter 19 of nvidia README... "If the EDID for the display device reported a preferred mode timing, and that mode timing is considered a valid mode, then that mode is used as the "nvidia-auto-select" mode." The EDID for my HDMI connected LCD monitor says use first device as preferred. Prefer first detailed timing : Yes Also: (--) NVIDIA(0): EDID maximum pixel clock : 230.0 MHz The list: (from startx -- -verbose 6 ) (--) NVIDIA(0): Detailed Timings: (--) NVIDIA(0): 1920 x 1080 @ 60 Hz (--) NVIDIA(0): Pixel Clock : 148.50 MHz (--) NVIDIA(0): HRes, HSyncStart : 1920, 2008 (--) NVIDIA(0): HSyncEnd, HTotal : 2052, 2200 (--) NVIDIA(0): VRes, VSyncStart : 1080, 1084 (--) NVIDIA(0): VSyncEnd, VTotal : 1089, 1125 (--) NVIDIA(0): H/V Polarity : +/+ This is the actual mode selected: (from xorg.0.log) (--) NVIDIA(0): 1920 x 1080 @ 60 Hz (--) NVIDIA(0): Pixel Clock : 74.18 MHz (--) NVIDIA(0): HRes, HSyncStart : 1920, 2008 (--) NVIDIA(0): HSyncEnd, HTotal : 2052, 2200 (--) NVIDIA(0): VRes, VSyncStart : 1080, 1084 (--) NVIDIA(0): VSyncEnd, VTotal : 1094, 1124 (--) NVIDIA(0): H/V Polarity : +/+ (--) NVIDIA(0): Extra : Interlaced (--) NVIDIA(0): CEA Format : 5 So my HTPC is down-converting to 1080i and then the Monitor is up-converting to 1080p How can I fix this, please?

  Read the article

• Kernel Panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) after apt-get upgrade

  - by Edward

  I'm using Ubuntu 9.1 server edition, I get this error during boot time after I ran sudo apt-get upgrade when checking my kernel version, uname -r returns 2.6.31-14-generic but when i run dpkg -l 'linux-image*' | grep ^.i I cannot find 2.6.31-14 (only contains 2.6.32*) Following the solution in the thread: Kernel Panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) doesn't work for me I'm running the commands inside the Rescue mode by booting from the Ubuntu 9.1 Installation Disc Do I need to update my kernel and run update-initramfs + update-grub again? If so, how can I update the kernel? apt-get install any linux-headers/image cannot change the uname -r value Thanks!

  Read the article

• 12.04 How to go back to command line only ubuntu

  - by Ne0

  I was attempting to install a command line only version of Ubuntu and followed the instructions here. I downloaded the alternate CD and went through the installation, but never got an "Install a command-line system." option. 12.04 is now up and running, though i don't need the desktop GUI. From what i have read i can set it back into text mode using grub, but what packages should i remove that i don't need any more?

  Read the article

• Can realtek 8192cu usb wireless card be used in ubuntu 12.04 with kernel 3.2.0?

  - by waterloo2005

  I do like the post RTL8188CUS Wireless USB Dongle doesn't work unless I disable wireless security . But when I plug my 8192cu usb wireless card, my computer screen is off. At that time I even can not use Alt SysRq k or Alt SysRq + reisub. I compile the latest driver of 8192cu on ubuntu 12.04 with kernel 3.2.0-34. In RealTek site, I download 8192cu drive which is for Linux Kernel 2.6.18~2.6.38 and Kernel 3.0.8. But now in Ubuntu12.04 my kernel is 3.2.0-34. Every time I plug the usb 8192cu wireless card my system halts. Now I try to blacklist both the system's rtl8192cu driver and the new 8192cu driver I compile, but the system still halts when I plug the usb driver. What about you ? Thanks!

  Read the article

• How can I export emacs documents in 13.04?

  - by Whippy

  When I try to export a document from org-mode in emacs, c-X, c-E now results in 'Can't find library org' whereas in 10.04 it opened the export dialog allowing me to produce html, pdf etc. from the source org file. Searching with Google, I found this bug for redhat which looks closely related. The trouble is I don't know how to get hold of the emacs-el package it talks about in ubuntu in order to try its workaround so I'm currently stuck.

  Read the article

• Flush kernel's TCP buffer with `MSG_MORE`-flagged packets

  - by timn

  send()'s man page reveals the MSG_MORE flag which is asserted to act like TCP_CORK. I have a wrapper function around send(): int SocketConnection_Write(SocketConnection *this, void *buf, int len) { errno = 0; int sent = send(this->fd, buf, len, MSG_NOSIGNAL); if (errno == EPIPE || errno == ENOTCONN) { throw(exc, &SocketConnection_NotConnectedException); } else if (errno == ECONNRESET) { throw(exc, &SocketConnection_ConnectionResetException); } else if (sent != len) { throw(exc, &SocketConnection_LengthMismatchException); } return sent; } Assuming I want to use the kernel buffer, I could go with TCP_CORK, enable whenever it is necessary and then disable it to flush the buffer. But on the other hand, thereby the need for an additional system call arises. Thus, the usage of MSG_MORE seems more appropriate to me. I'd simply change the above send() line to: int sent = send(this->fd, buf, len, MSG_NOSIGNAL | MSG_MORE); According to lwm.net, packets will be flushed automatically if they are large enough: If an application sets that option on a socket, the kernel will not send out short packets. Instead, it will wait until enough data has shown up to fill a maximum-size packet, then send it. When TCP_CORK is turned off, any remaining data will go out on the wire. But this section only refers to TCP_CORK. Now, what is the proper way to flush MSG_MORE packets? I can only think of two possibilities: Call send() with an empty buffer and without MSG_MORE being set Re-apply the TCP_CORK option as described on this page Unfortunately the whole topic is very poorly documented and I couldn't find much on the Internet. I am also wondering how to check that everything works as expected? Obviously running the server through strace' is not an option. So the only simplest way would be to usenetcat' and then look at its `strace' output? Or will the kernel handle traffic differently transmitted over a loopback interface?

  Read the article

• My kernel only works in block (0,0)

  - by ZeroDivide

  I am trying to write a simple matrixMultiplication application that multiplies two square matrices using CUDA. I am having a problem where my kernel is only computing correctly in block (0,0) of the grid. This is my invocation code: dim3 dimBlock(4,4,1); dim3 dimGrid(4,4,1); //Launch the kernel; MatrixMulKernel<<<dimGrid,dimBlock>>>(Md,Nd,Pd,Width); This is my Kernel function __global__ void MatrixMulKernel(int* Md, int* Nd, int* Pd, int Width) { const int tx = threadIdx.x; const int ty = threadIdx.y; const int bx = blockIdx.x; const int by = blockIdx.y; const int row = (by * blockDim.y + ty); const int col = (bx * blockDim.x + tx); //Pvalue stores the Pd element that is computed by the thread int Pvalue = 0; for (int k = 0; k < Width; k++) { Pvalue += Md[row * Width + k] * Nd[k * Width + col]; } __syncthreads(); //Write the matrix to device memory each thread writes one element Pd[row * Width + col] = Pvalue; } I think the problem may have something to do with memory but I'm a bit lost. What should I do to make this code work across several blocks?

  Read the article

• Using a 64bit Linux kernel, can't see more than 4GB of RAM in /proc/meminfo

  - by Chris Huang-Leaver

  I'm running my new computer which has 8GB of RAM installed, which is visable from BIOS page, does not show in /proc/meminfo uname -a Linux localhost 3.0.6-gentoo #2 SMP PREEMPT Sat Nov 19 10:45:22 GMT-- x86_64 AMD Phenom(tm) II X4 955 Processor AuthenticAMD GNU/Linux The result of /proc/meminfo is as follows: (thans Andrey) MemTotal: 4021348 kB MemFree: 1440280 kB Buffers: 23696 kB Cached: 1710828 kB SwapCached: 4956 kB Active: 1389904 kB Inactive: 841364 kB Active(anon): 1337812 kB Inactive(anon): 714060 kB Active(file): 52092 kB Inactive(file): 127304 kB Unevictable: 32 kB Mlocked: 32 kB SwapTotal: 8388604 kB SwapFree: 8047900 kB Dirty: 0 kB Writeback: 0 kB AnonPages: 492732 kB Mapped: 47528 kB Shmem: 1555120 kB Slab: 267724 kB SReclaimable: 177464 kB SUnreclaim: 90260 kB KernelStack: 1176 kB PageTables: 12148 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 10399276 kB Committed_AS: 3293896 kB VmallocTotal: 34359738367 kB VmallocUsed: 317008 kB VmallocChunk: 34359398908 kB AnonHugePages: 120832 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 2048 kB DirectMap4k: 23552 kB DirectMap2M: 3088384 kB DirectMap1G: 1048576 kB I have tried using mem=8G as a kernel boot parameter, I read a post about setting HIGHMEM64G to yes, before realising that only applies to 32bit kernels. Trying dmindecode -t memory SMBIOS 2.7 present. Handle 0x0026, DMI type 16, 23 bytes Physical Memory Array Location: System Board Or Motherboard Use: System Memory Error Correction Type: Multi-bit ECC Maximum Capacity: 32 GB Error Information Handle: Not Provided Number Of Devices: 4 Handle 0x0028, DMI type 17, 34 bytes Memory Device Array Handle: 0x0026 Error Information Handle: Not Provided Total Width: 64 bits Data Width: 64 bits Size: 4096 MB Form Factor: DIMM Set: None Locator: DIMM0 Bank Locator: BANK0 Type: <OUT OF SPEC> Type Detail: Synchronous Speed: 1333 MHz Manufacturer: Manufacturer0 Serial Number: SerNum0 Asset Tag: AssetTagNum0 Part Number: Array1_PartNumber0 Rank: Unknown Handle 0x002A, DMI type 17, 34 bytes Memory Device Array Handle: 0x0026 Error Information Handle: Not Provided Total Width: Unknown Data Width: 64 bits Size: No Module Installed Form Factor: DIMM Set: None Locator: DIMM1 Bank Locator: BANK1 Type: Unknown Type Detail: Synchronous Speed: Unknown Manufacturer: Manufacturer1 Serial Number: SerNum1 Asset Tag: AssetTagNum1 Part Number: Array1_PartNumber1 Rank: Unknown Handle 0x002C, DMI type 17, 34 bytes Memory Device Array Handle: 0x0026 Error Information Handle: Not Provided Total Width: 64 bits Data Width: 64 bits Size: 4096 MB Form Factor: DIMM Set: None Locator: DIMM2 Bank Locator: BANK2 Type: <OUT OF SPEC> Type Detail: Synchronous Speed: 1333 MHz Manufacturer: Manufacturer2 Serial Number: SerNum2 Asset Tag: AssetTagNum2 Part Number: Array1_PartNumber2 Rank: Unknown Handle 0x002E, DMI type 17, 34 bytes Memory Device Array Handle: 0x0026 Error Information Handle: Not Provided Total Width: Unknown Data Width: 64 bits Size: No Module Installed Form Factor: DIMM Set: None Locator: DIMM3 Bank Locator: BANK3 Type: Unknown Type Detail: Synchronous Speed: Unknown Manufacturer: Manufacturer3 Serial Number: SerNum3 Asset Tag: AssetTagNum3 Part Number: Array1_PartNumber3 Rank: Unknown

  Read the article

• iotop for Linux kernel 2.6.18

  - by Lightsauce

  So it has to come to my attention that iotop isn't availalbe for 2.6.18 since it's less than 2.6.20 and requires Python 2.6+. I've done some research and came across this article: http://lserinol.blogspot.com/2009/09/io-usage-per-process-on-linux.html According to this, if these process have io stats in /proc/pid#/io (where pid# is the process #) it's doable regardless of the kernel version. So, in reality, I could upgrade Python to 2.6 and test out iotop. However, my flavor of Linux, CentOS release 5.5 (Final), only supports Python 2.4.3-44.el5 currently. If I were to do uninstall from yum, it doesn't look so pretty. It ends up wanting to uninstall 235 packages, most of which are very important! I read in one place, online (I forget the URL from yesterday), that you can install Python 2.6+ parallel to this one, and have the rpm install for iotop use that. Well, I didn't choose that route. I figured, what the heck, lets write iotop (not copying it, but reverse engineering it without actually looking at it's code/it in use) in bash. I thought it would just grab the /proc/pid#/io file and parse stats. So I wrote a script to grab the top 10 rchar, wchar, read_bytes, and write_bytes by collecting all these stats from all the /proc/pid#/io files, sorting them by each metric, then grabbing the top 10 highest values. The conclusion, the data seems completely useless. Does anybody know any resources for advanced Linux where I can figure out how to take these /proc/pid#/ directories and figure out what the heck they are doing with io on the disk? My main goal is to figure out what exactly is causing high load on my disk. I just know it's on the / partition (/dev/sda2 in this case), and I'm not really sure how to narrow it down without the help of iotop. If I run iostat to grab metrics for 1 minute, every second, the first result it gives me shows a high 'kB_read/s', so that makes me think, it's reading mostly. However, if I watch the update it gives me every second, it's actually just showing values for kB_wrtn/s. This makes me think the initial value iostat gives me is misleading.

  Read the article

• Is there a way to hide the Primefaces fileUpload progress bar and buttons in advanced mode and auto mode?

  - by Joe Roberts

  Is there a way to hide the Primefaces fileUpload progress bar and buttons in advanced mode and auto mode? Here is the code that I am using: <p:fileUpload id="scriptUpload" widgetVar="importDevicesWidget" fileUploadListener="#{scriptUploadBean.handleFileUpload}" auto="true" label="Choose.." mode="advanced" update=":infoMessages" sizeLimit="8192" allowTypes="/(\.|\/)(txt)$/" onstart="clearInvalidFileMsg();$('#progress').show();" oncomplete="clearInvalidFileMsg();$('#progress').hide();importDevicesDialogWidget.hide()"/> The problem is that it makes no sense for the buttons that appear next to the progress bar for each file to be there as the mode is auto so the upload already started! Here is a screen shot:

  Read the article

• HAProxy not passing SSL traffic in TCP mode (unknown protocol)

  - by David

  Hi, I've got a HAProxy LB solution setup and working correctly. All HTTP traffic on port 80 is being passed through succesfully. I'm now trying to get SSL traffic to work (in TCP mode and on just one server for now) however I keep getting the following error when testing via openssl: 26396:error:140770FC:SSL routines:SSL23_GET_SERVER_HELLO:unknown protocol:s23_clnt.c:588: However, when I try the same test (openssl s_client -connect) on the web servers IP address and hostname, everything seems to look OK. I can setup a hosts record locally and confirm that the browsers are picking up the SSL certificate succesfully for the domain. I guess this has led me to the conclusion that there is a problem at the HAProxy setup I have, so would really appreciate some advice here. frontend https-c-in bind 178.79.xxx.xxx:443 mode tcp default_backend c-https backend c-https balance source option ssl-hello-chk option httpclose server c-web-01 192.168.xxx.xxx:443 check inter 2000 rise 2 fall 5

  Read the article

• Optional parameters with PHP SoapClient class on wsdl mode

  - by Maraino

  With the SoapClient class on PHP5.x and working against a SOAP web service that has optional parameters in its methods, you won't have any problem if you use the non-wsdl mode. But, at least by default, with the wsdl mode, if you don't fill all the parameters you will get an error like: SOAP-ERROR: Encoding: object hasn't 'xxx' property Is there any way to avoid that error without working with the non-wsdl mode and without filling all the parameters?

  Read the article

• 'skb rides the rocket' on Xen VM

  - by Kye

  I've just set up Ubuntu 13.10 server as a VM on my Ubuntu/Xen server, and I'm getting these weird lines in my syslog. Nov 12 10:26:32 human kernel: [130782.315333] xennet: skb rides the rocket: 19 slots Nov 12 10:26:32 human kernel: [130782.362405] xennet: skb rides the rocket: 20 slots Nov 12 10:26:32 human kernel: [130782.408458] xennet: skb rides the rocket: 19 slots Nov 12 10:26:32 human kernel: [130782.490260] xennet: skb rides the rocket: 20 slots Nov 12 10:26:32 human kernel: [130782.541931] xennet: skb rides the rocket: 19 slots Nov 12 10:26:35 human kernel: [130785.226635] xennet: skb rides the rocket: 19 slots Nov 12 10:26:35 human kernel: [130785.261026] xennet: skb rides the rocket: 21 slots Nov 12 10:26:35 human kernel: [130785.469306] xennet: skb rides the rocket: 19 slots Nov 12 10:26:36 human kernel: [130786.552730] xennet: skb rides the rocket: 21 slots Nov 12 10:26:38 human kernel: [130788.212747] xennet: skb rides the rocket: 20 slots Nov 12 10:26:38 human kernel: [130788.257544] xennet: skb rides the rocket: 19 slots Nov 12 10:26:38 human kernel: [130788.903841] xennet: skb rides the rocket: 19 slots Unsure of what they mean, and Google has nothing meaningful. Any help is appreciated.

  Read the article

• Debuging CUDA kernels called from .NET code in VS2008, emulation mode

  - by Danny Varod

  CUDA has an option to compile code in emulation mode, which is supported in the .rules file they provide. I have C# .NET 3.5 SP1 code that calls a native dll, using DllImport, the native dll is compiled via VS2008 using nvcc and its function is to transfer memory from and to CUDA and to invoke CUDA kernels. When the CUDA kernels are correct, everything runs fine, but when there is a bug, I can only step in to the code until the title of the kernels and see the parameters they receive. (I enabled debugging native code in the startup-project's debug options.) I have tried compiling with emulation mode, however I get the CUDA error "mixed device execution" when calling the CUDA memcopy host--device. I tried switching the alloc+dealloc+memcopy with their equivalent non-CUDA versions, but then the same error occurs when invoking the kernels. What did I do wrong in my attempt to using the debug-emulation mode? P.S. I tried this on Vista x64 SP1 + VS2008, with the same solution complied in both x86 and x64, neither worked in emulation mode, both worked in non-emulation mode.

  Read the article

• Unable to run openoffice in headless mode

  - by uswaretech

  I want to automoate some PPT - PDF conversions, so I want to run openoffice in headless mode for scripting. On my machine with X running I can start opemoffice in headless mode via soffice -accept="socket,port=8100;urp;" -headless This doesn't seem to work on a server with X not running. $ soffice -accept="socket,port=8100;urp;" -headless /usr/lib/openoffice/program/soffice.bin X11 error: Can't open display: Set DISPLAY environment variable, use -display option or check permissions of your X-Server (See "man X" resp. "man xhost" for details) $ The error doesnt seem to make sense as well, as the point of specifying -headless was so that I do not need X, while this command seems to look for X.

  Read the article

• Pre-built UI components for displaying SSRS Local Mode Parameters

  - by namenlos

  BACKGROUND Am writing a WinForm app that uses the SSRS Report Viewer control to render reports in local mode - there is no SSRS server involved at all I can successully create and execute reports in local mode What I want to do is add Parameters to the report THE PROBLEM When the Report Viewer control executes a report in local mode it does not provide any UI that allows the user to enter values for parameters defined in the report This is in contrast to to when the Report Viewer control is running a server report - parameters are shown. MY QUESTION Are there pre-built components or even sample code I can use that would provide a reasonble parameter user experience for this scenario (scenario = SSRS + Report Viewer Control + Local Mode)? Yes, I could write this UI code myself - what I am looking for is existing code to avoid having to implement this UI because I'd rather spend my time making the content of the report work well NOTES Switching to another reporting engine besides SSRS is not an option. Switching to server side reports is not an option.

  Read the article

• Kernel Mode Rootkit

  - by Pajarito

  On the other 3 computers in my family, I believe that we have a kernel-mode rootkit for windows. It appears that the same rootkit is on all of them. We think. We changed all the important passwords from my computer, running linux right now. On all of the infected computers is Symantic Endpoint Protection, because it's free from the university where my mom and dad work. In my opinion symantec is a piece of crap, seeing as it didn't even manager to delete the tracking cookies it found when I tried it on my own computer. The Computers and their set-ups: Computer A: Vista Business; symantec antivirus. runs it as admin, no password. IE8. no other security software other than what comes with windows. IE8 security settings the default Computer B: XP Home Premium; symantec antivirus. runs as normal user, no password, admin account with weak password, spybot, uses IE8 with default settings, sometimes Firefox Computer C: XP Home Premium; symantec antivirus. runs as normal user, no password, admin account with weak password, uses IE8 with default settings, no other security programs except what came with windows This is what's happening. Cut and pasted from my dad's forum post. -- When I scanned my laptop (Dell XPS M1330 with Windows Vista Small Business), Symantec Endpoint Protection hangs for a while, perhaps 10 seconds or so, on some of the following files 9129837.exe, hide_evr2.sys, VirusRemoval.vbs, NewVirusRemoval.vbs, dll.dll, alsmt.ext, and _epnt.sys. It does this if a run a scan that I set up to run on a new thumbnail drive and it does this even if the thumbnail is not plugged in. It doesn't seem to do this if I scan only the C: drive. I've check for problems with symantec endpoint protection and also with Microsoft Security Essentials and Malwarebytes Anti-Malware. They found nothing and I can't find anything by searching for hidden files. Next I tried microsoft's rootkitrevealer. It (rootkitrevealer) finds 279660 (or so) discrepancies and the interface is so glitchy after that I can't really figure out what is going on. The screen is squirrely. The rootkitrevealer pulls up many files in the folder \programdata\applicationdata and there are numberous appended \applicationdata on the end of that as well. -- As you can see, what we did was install MSE and MBAM and scan with both of them. Nothing but a tracking cookie. Then I took over and ran rootkitrevealer.exe from MicroSoft from a flash drive. It found a bunch of discrepancies, but only about 20 or so where security related, the rest being files that you just couldn't see from Windows Explorer. I couldn't see whether of not the files list above, the ones that the scan was hanging on, where in the list. The other thing is, I have no idea what to do about the things the scan comes up with. Then we checked the other computers and they do the same thing when you scan with Symantec. The people at the university seen to think that dad might not have a virus, but 2 of the computers slowed down noticably AND IE8 started acting all funny. None of my family is very computer oriented, and 2 of the possible causes for the rootkit are: -My dad bought a new flash drive, which shipped with a data security executable on it -My dad has to download lots of articles for his work Those are the only things that stand out, but it could have been anything. We are currently backing up our data, and I'll post again after trying IceSword 1.22. I just looked at my dad's forum topic, and someone recommended GMER. I'll try that too.

  Read the article

• Configure IIS 7.0 to enable webservices in classic mode

  - by intermension

  What are the configuration file settings to enable webservices on IIS 7.0 in classic mode? The site has to be in a classic mode application pool because the Report Viewer controls crash when running in Integrated Mode. However in a classic mode application pool, webservices produce the following error message: The requested content appears to be script and will not be served by the static file handler. •If you want to serve this content as a static file, add an explicit MIME map EDIT - Additional Error Message Info: HTTP Error 404.17 - Not Found Module: StaticFileModule Notification: ExecuteRequestHandler Handler: StaticFile Error Code: 0x80070032 Note: This particular instance of the application will be running in a customers account on a shared hosting enviroment so access to IIS UI is not/will not be available. Specifically seeking configuration file adjustments.

  Read the article

• Windows 7 + Deep Freeze - I'm stuck in an endless reboot loop

  - by myermian

  I have the following setup: Windows 7 Ultimate Deep Freeze I "thawed" my machine last night and performed a Windows Update. The update is having issues (it gets stuck at 32%, fails, and restarts my machine). When it reboots it attempts it again, and again, and again, etc. (Endless loop). I looked online and found some solutions, but none of them seem to be working: When I run Safe Mode, Safe Mode w/ Network, or Safe Mode w/ Command Prompt it attempts to revert the Windows Update changes. However, the problem is with Deep Freeze on (and now in "Frozen" mode) the reverted changes don't stay, and I'm back into the loop of death. Oh, and side note: "Safe Mode w/ Command Prompt" does not actually take me to a command prompt window? Perhaps because it is attempting to complete the Windows Update changes first? I have tried to select the option to NOT restart when an windows error occurs, but it still does. I tried the remainder of all the other options in the F8 screen. The only other option left is to find my Windows 7 Media Disc (I can't find it right now) and use it to repair windows (because for some reason the repair option does not show up in the F8 screen). Is there a way to disable Deep Freeze from loading? When I selected "Safe Mode w/ Command Prompt" I noticed that it loads the DpFrz.sys file. I know that when I'm in the Windows Boot Manager if I press F10 instead of F8 (while highlighting Windows 7) it takes me to an "Edit Boot Options" screen: Edit Windows boot options for: Windows 7 Path: \Windows\system32\winload.exe Partition: 2 Hard Disk: 8e90e329 [ /NOEXECUTE=OPTIN (I CAN EDIT THIS LINE) ] Update: I found my Windows 7 Media Disk and it did not help out. The laptop had the "System Restore" as a partition on the HDD. I later received (in the mail) a Windows 7 Upgrade Disc from Sony to upgrade my system from Windows Vista to Windows 7 Ultimate. I placed the disc into the DVD drive and it does not come up as a "bootable" disc. I'm going to try to find an alternative disc to see if I can get into Command Prompt. Update 2: I got a Windows Repair disc and got into a command prompt window. I got into the registry and disabled Deep Freeze. Also: I renamed the Pending.xml file to Pending.old I cleared out the Windows Temp directory I still am stuck in the loop (though, it isn't an issue with DeepFreeze anymore because I can make changes to the hard drive and they persist). Not sure what to do at this point? Update 3: I ran the repair option and it couldn't repair, but it did point me to something. It says the error was due to a driver that was failing. I have a feeling it is my UPEK Fingerprint scanner.

  Read the article

• DOS/Command Prompt Power Mode

  - by King

  from where can i get a Bootable or Executable Power Mode DOS/Command Prompt.

  Read the article

• VM can’t connect to outside in bridged mode

  - by Kamal

  Hi Guys, I am not able to ping any machine(not even the host) from Guest VM in bridged mode. But I got an IP which is on the same subnet as host. I can ping my guest VM from the host and can use ssh to connect to the guest. I am using Vmware workstation 6.5. Guest VM is a centos VM and host is windows xp. Every thing works fine in NAT mode. Any clues as to what could be happening. I tried disabling all the firewalls I have. My virtual network editor shows that my ethernet adapter(the one my host uses) is used for bridging. It is connected. I don't understand how I can get an IP address from DHCP server. I can't ping any of the DNS servers in generated /etc/resolv.conf which are the same as that of my host

  Read the article

• Intellij + GWT 2: Development Mode ignores changes to static content

  - by Kaffeine Coma

  The new Development Mode in GWT 2 is awesome, but unfortunately as launched from Intellij IDEA 9, it does not seem to notice changes made to static files such as html, css, etc. It immediately see changes in *.java files, but not the static ones. If I make a change in a static file I need to quite the Development Mode tool and re-launch it. This is painfully slow, and negates much of the point of using dev mode in the first place I assume this is some artifact resulting from the way the Intellij runner launches it- it creates an out/artifacts/project_war_exploded directory with the static content and class files. How can I get Intellij Dev Mode tool to follow changes made to the original static source files?

  Read the article

• IE9 Kiosk Mode scheduled task opens behind taskbar

  - by greg27

  I've set up a scheduled task in Windows 7 Pro to open up Internet Explorer 9 (x86 version) in kiosk mode. The scheduled task executes when a certain user logs in, and this user is logged in automatically when Windows starts. This is the command I'm using to start IE: "C:\Program Files (x86)\Internet Explorer\iexplore.exe" -k http://example.com So far so good - the computer boots up, the user gets logged in, and IE opens up in kiosk mode. The problem is that IE seems to open behind the taskbar - so the taskbar (start menu, pinned programs, etc.) appears at the bottom of the window, and the bottom of the IE window is visible through the taskbar (since the taskbar is translucent). Is there anything I can do, preferably without installing any third party programs (although I will go for that option if none other is available), to ensure that the IE9 kiosk window always opens in front of the taskbar?

  Read the article

• VM can't connect to outside in bridged mode

  - by Kamal

  I am not able to ping any machine(not even the host) from Guest VM in bridged mode. But I got an IP which is on the same subnet as host. I can ping my guest VM from the host and can use ssh to connect to the guest. I am using Vmware workstation 6.5. Guest VM is a centos VM and host is windows xp. Every thing works fine in NAT mode. Any clues as to what could be happening. I tried disabling all the firewalls I have.

  Read the article

< Previous Page | 53 54 55 56 57 58 59 60 61 62 63 64  | Next Page >