Search Results

Search found 6612 results on 265 pages for 'seconds'.

Page 57/265 | < Previous Page | 53 54 55 56 57 58 59 60 61 62 63 64  | Next Page >

• ASUS N56VZ-S4209P Screen saver, Screen dimming,sleep/hibernation mode not working according to power management settings

  - by Alto Roos

  I have a problem with my ASUS N56VZ-S4209P(Win8, I7-3630QM) laptop. If I use the fn+f7 command to turn off the screen it turns on by itself after a few seconds (the time varies between 1-10 seconds). In addition to this my screensaver doesn't activate at all and the laptop doesn't dim its screen after X minutes or goes into sleep/hibernation mode as specified in the power options when plugged in or on battery. As far as my knowledge goes it's not caused by the mouse or track pad at all since I can unplug my mouse and disable the track pad but the problem persist. I presume this is caused by the same problem? Does anyone know of a fix for this problem? It would be greatly appreciated. . . . I seem to have found a solution to the problem related to the screen that turns itself on again. The Power4Gear application has a setting which enables you to turn a "Presentation mode" "On" and "Off", if that setting is "Off" then it doesn't turn the screen on without any human interaction. Thus that part of the problem is fixed.

  Read the article

• Dell PE2950 - slow IO rates for writing and reading locally

  - by OrenM

  I'm having a serious issue with dell server PE2950. The server has really slow IO rates, so slow that I'm not able to use it anymore I tried few things to solve this: changing disks to new disks (configured them as raid1) changing perc card + perc cables reinstalling the OS of course, had to cause of changing of disks, centos 5.5 x64bit firmware update to everything virtual disks policy: No Read Ahead,Write Back, disk cache policy disabled. openmanage doesn't alert about anything, also i ran dell's diag tests, everything passed, also dell didn't see anything in deset log. dell offered to reseat everything, including the cpu, we did that as well, still io rates are slow I have several PE2950 servers, and I never had such a thing with any of those. All have similar or exact hardware as this one, all configured the same, with the same os centos 5.5 x64, same disks, same raid, same policy. Just for comparison: the problematic PE2950 server: [root@bad ~]# time sh -c "dd if=/dev/zero of=/tmp/ddfile bs=8k count=200000 && sync" 200000+0 records in 200000+0 records out 1638400000 bytes (1.6 GB) copied, 27.7946 seconds, 58.9 MB/s real 0m33.968s user 0m0.531s sys 0m26.000s good PE2950 server (with the exact same hardware): [root@good ~]# time sh -c "dd if=/dev/zero of=/tmp/ddfile bs=8k count=200000 && sync" 200000+0 records in 200000+0 records out 1638400000 bytes (1.6 GB) copied, 3.19999 seconds, 512 MB/s real 0m7.694s user 0m0.053s sys 0m4.057s Hopefully you will have an idea what can cause the problem.

  Read the article

• Puppet file transfer slow

  - by Noodles

  I have a puppet master and slaves in different datacenters. The latency between them is ~40ms. When I run "puppet agent --test" on a slave to apply the latest manifest it takes ~360 seconds to finish. After doing some digging I can see the main cause of the slow down is file transfers. It seems it's taking ~10 seconds to transfer each file. The files are only small (configuration files) so I can't understand why they would take so long. This is an example of a file in my manifest: file { "/etc/rsyncd.conf" : owner => "root", group => "root", mode => 644, source => "puppet:///files/rsyncd/rsyncd.conf" } Running puppet-profiler I see this: 10.21s - File[/etc/rsyncd.conf] It also seems I cannot update more than one server at once using puppet. If I run two servers at the same time then puppet takes twice as long. I have changed the puppet master from using webrick to mongrel, but this doesn't seem to help. This is making deploying changes painful. A simple config change can take an hour to roll out to all servers.

  Read the article

• Ubuntu 10.04 Server on Hyper-V Server R2 has sluggish install and command line

  - by Paul Hobart

  I've installed Ubuntu Server 10.04 (64 bit) on a Hyper-V Server R2. I've encountered two issues that I think are related: Very slow install Very slow command prompt The text-mode installer goes through a series of text-based prompt windows. It takes 7-10 seconds for each of these windows to draw on the screen. The end result is that every time I answer a prompt and hit enter I wait for 15 seconds while the screen redraws line by line. I can literally see each line of text being drawn (like the old 300 baud modems days). Once done installing, scrolling on the command line is super slow. For instance, if a simple command, like "ls", causes the screen to scroll, it will scroll very slowly. This happens on a fresh install. The server functions as a LAMP server and an OpenSSH server, but that's it (I don't even have any Virtual Hosts set up yet). AND this only happens on the Virtual Machine console. I access the console through Hyper-V Manager and don't have this problem on any of my other Virtual Machines. Also, this problem does NOT happen when accessing a shell through OpenSSH. How can I improve this performance issue?

  Read the article

• Apache 2.4 Prefork vs. PHP-FPM Event shows sig decrease in requests per second

  - by Mark

  On my Apache 2.4.2 server with a standard mod_php Prefork setup these are my server-status results Current Time: Wednesday, 24-Oct-2012 19:36:24 CDT Restart Time: Wednesday, 24-Oct-2012 01:27:30 CDT Parent Server Config. Generation: 1 Parent Server MPM Generation: 0 Server uptime: 18 hours 8 minutes 54 seconds Total accesses: 14304233 - Total Traffic: 342.3 GB CPU Usage: u12584.6 s721.93 cu.66 cs3.43 - 20.4% CPU load 219 requests/sec - 5.4 MB/second - 25.1 kB/request 507 requests currently being processed, 355 idle workers ______KKKKR_K______W_KKC___CKK_K_K_W__CC_KKK_KK._K_K_KK._KKKK_K_ K_____KK_KKKK_K_KK__K___KK_K___K_____CKKK_WK_K_____KCKK__K___K_K K_CK_K_K_____K__KKKK_K__K___K_KK_K_K_KKKCK____________KK_CK__KKK __C_KKKKKKK___CK___C_KKK_K__C__K_CK____KKK__K__K__K_K__KK_CK_K__ _KKKKK_K_W__KK______K___K__W___C_K__K____KKKKKKKK.KKKKKKKCK_K___ _C_KK_K_WK__K_KK__K__RK_KK___K____K_KK_K_K___RKC_KKKK___KKKC_K_W _C_KK_KK__W____KC__KKK__KKK___K___KKK_KK_K_KKW__K_KR_KK_KK__KKK_ R__KKK__KKKKKK__K_KKKKK_K__K_K___KKW_________KK_K___KKK___KK.K_C KKKKKKW_____K__K_KKC_KCKK_K_KK_K__KK__K___K__KK_KK__________KK__ __K___KK_K__K_C_KK_K___KK__KK__K__KCK_K__KK_________K_K_KK__.K__ K_CKK.CCRW__KKKKKKKKKKKC__W____K___KWK_KK_KKC______.K_K_KK_KKKC_ __KKK_W_KCKKK_K_K____CCCK__KC_KKKK_K____K_CK_K____K__K____KKK_KK KK___K_K_K__KW__KCKKKK____WKWK__K_KKRKK__C_K_KK_KK_K__KKCC_K__C_ KK_K___K_KK______K_____CKK_K_______KK_CKCK__KKKKK____K__K..K____ __KKWK_KW__KKK__K_KKK___K_KK_KKK__KK___KK___KK_KK___KK____KKWKKC KK_KKKK_................................` When I switch to a PHP-FPM setup with the Event MPM with no other variables changes, my requests/sec plummet and overall apache response is garbage. Current Time: Wednesday, 24-Oct-2012 19:51:21 CDT Restart Time: Wednesday, 24-Oct-2012 19:48:03 CDT Parent Server Config. Generation: 1 Parent Server MPM Generation: 0 Server uptime: 3 minutes 18 seconds Total accesses: 18720 - Total Traffic: 307.1 MB CPU Usage: u16.57 s4.74 cu0 cs0 - 10.8% CPU load 94.5 requests/sec - 1.6 MB/second - 16.8 kB/request 15 requests currently being processed, 49 idle workers PID Connections Threads Async connections total accepting busy idle writing keep-alive closing 11701 114 no 10 22 0 66 38 11702 134 no 5 27 0 81 48 Sum 248 15 49 0 147 86 __R_R__W___RRW________RR__R___W_W_______W_____W_____________R_R_ Is there any obvious reason anyone could think of why this would be the case. I can provide any other additional stats or server setup info to help out. Ive tried tweaking everything up and down and nothing really helps get the PHP-FPM setup anywhere near a baseic prefork/mod-php setup. Thanks!

  Read the article

• nVidia performance with newer X and newer driver abysmal with Compiz

  - by Nakedible

  I recently upgraded Debian to Xorg 2.9.4 and installed nvidia-glx from experimental, version 260.19.21. This was somewhat of an uphill battle as the dependencies for the experimental nvidia-glx package are still somewhat broken. I got it to work without forcing the installation of any packages and without modifying the packages. However, after the upgrade compiz performance has been abysmal. I am using the desktop wall plugin and switching viewports is really slow - takes a few seconds for each switch. In addition to this, every effect that compiz does, such as zoom animations for icons when launching applications, takes seconds. The viewport switching speed changes relative to the amount of windows on that virtual screen - empty screens switch almost at normal speed, single browser windows work almost decently, but just 4 rxvt terminals slows the switches down to a crawl. My compiz configuration should be pretty basic. Xorg is likewise configured without anything special - the only "custom" configuration is forcing the driver name to be "nvidia". I've fiddled around with the nvidia-settings and compizconfig trying different VSync settings, but none of those helped. My graphics card is: NVIDIA GPU NVS 3100M (GT218) at PCI:1:0:0 (GPU-0). This is laptop GPU that is from the Geforce GTX 200 series. Graphics card performance should naturally be no problem.

  Read the article

• Fliping the video stream in Sony Vegas Studio!

  - by NoCanDo

  How do I flip a video stream, making it effectively appear to run backwards. For example, I've got a 6 second video stream. I cut it at 2, 4, 6, so I've got now 3 seperate streams with 2 seconds each. 1-2 ; 3-4; 5-6 - That how it'll be displayed normal. Now what I want to do in Sony Vegas is to copy/paste and flip a selected stream. Let say: 1-2; 3-4; 3'-4' (copy/pasted); 5-6 - Now I've got a video stream with 8 seconds. Now I want to flip this copy pasted making it effectively run backwards. 1-2; 3-4; 4'-3'; 5-6. The idea is I want something like a movie, it goes, and goes and goes, then a text appears "WAIT! What just happend?", then the movie goes back to second 3 (1-2-3-4-'WAIT, WHAT JUST HAPPEND?'-4-3-4-5-6. I hope you get what I want to do in Sony Vegas.

  Read the article

• Trying to build OpenSimulator.. nant fails

  - by Gary

  Output of nant is: Buildfile: file:///root/opensim-0.6.8-release/OpenSim.build Target framework: Mono 2.0 Profile Target(s) specified: build [echo] Using 'mono-2.0' Framework init: Debug: [echo] Platform unix build: [nant] /root/opensim-0.6.8-release/OpenSim/Framework/Servers/HttpServer/OpenSim.Framework.Servers.HttpServer.dll.build build Buildfile: file:///root/opensim-0.6.8-release/OpenSim/Framework/Servers/HttpServer/OpenSim.Framework.Servers.HttpServer.dll.build Target framework: Mono 2.0 Profile Target(s) specified: build build: [echo] Build Directory is /root/opensim-0.6.8-release/OpenSim/Framework/Servers/HttpServer/bin/Debug [csc] Compiling 29 files to '/root/opensim-0.6.8-release/OpenSim/Framework/Servers/HttpServer/bin/Debug/OpenSim.Framework.Servers.HttpServer.dll'. [csc] /root/opensim-0.6.8-release/OpenSim/Framework/Servers/HttpServer/AsynchronousRestObjectRequester.cs(103,41): error CS0246: The type or namespace name `TResponse' could not be found. Are you missing a using directive or an assembly reference? [csc] Compilation failed: 1 error(s), 0 warnings BUILD FAILED - 0 non-fatal error(s), 1 warning(s) /root/opensim-0.6.8-release/OpenSim/Framework/Servers/HttpServer/OpenSim.Framework.Servers.HttpServer.dll.build(14,6): External Program Failed: /usr/lib/pkgconfig/../../lib/mono/2.0/gmcs.exe (return code was 1) Total time: 1.2 seconds. BUILD FAILED Nested build failed. Refer to build log for exact reason. Total time: 1.3 seconds. OS is Fedora 7. Any ideas appreciated. :)

  Read the article

• Prolific USB-to-Serial Comm Port significantly slower under Windows 7 comparing to Windows XP

  - by Dmitry S

  Not sure if this question should be asked here or on SuperUser but if we get an answer here it may be useful for others here I am using a Prolific USB-to-Serial adapter based on the Prolific chip to use with a device on serial port. I have the latest version of the driver installed: 1.3.0 (2010-7-15). When I use my device with this adapter on my main Windows 7 (32bit) system it takes 8-9 seconds to send a command through to the device. However, when I do the same thing on a different Windows XP system (an old laptop I borrowed for testing) it only takes 2-3 seconds. I have made sure that the port settings and other variables are the same between systems. I also tested on a third laptop (also running Windows 7) and again got a significant delay. So the question is if anyone else experienced the same problem and found a solution. I would like to avoid moving to an XP system for what I need to achieve so that's my last option. Thanks in advance.

  Read the article

• Mainboard shuts itself off after half a second or so

  - by heishe

  Here's the problem: When I start the PC, the mainboard powers up, then stays that way maybe 0.2-0.5 seconds, and then shuts off again. I say mainboard, and not PC, because I removed all the parts from the system and disconnected everything but the mainboard power supply (the broad 12 pin thingy). When I have the other parts (cpu, graphics card, ram, etc.) installed and connected, the basic behaviour stays the same, but now the mainboard runs for about 6 or 7 seconds (this is a guess) before shutting off. This all started when my monitor wouldn't receive a video signal today, without giving POSTs, so I took the graphics card and the RAM out to see if it changes anything. It didn't, except that from that point on the mainboard would start to have this behavior where it just stays on for a very short time and then shuts off again. I already tested it with a backup PSU - same behavior. What could this be? I'm thinking it can't be on a physical level (transistors burned through or something like that), since then the mainboard either shouldn't start at all or it should detect hardware failures in non-essential parts of the syste and start beeping. Sorry, I forgot to mention. It's an MSI P67A-C43. I already checked the capacitors if someone popped, but I can't find anything. I also tried resetting the cmos, but that didn't change anything.

  Read the article

• Request bursting from web application Load Tests

  - by MaseBase

  I'm migrating our web and database hosting to a new environment on all new machines. I've recently performed a Load Test using WAPT to generate load from multiple distributed clients. The server has plenty of room to handle the traffic load, but I'm seeing an odd pattern of incoming traffic during the load tests. Here is the gist of our setup: Firewall server running MS Forefront TMG 2010 on Win 2k8 server Request routing done by IIS Application Request Routing on firewall machine Web server is a Hyper-V VM on the Database server (which is the host OS) These machines are hefty with dual-CPU's with six cores (12 total procs) Web server running IIS 7.5 Web applications built in ASP.NET 2.0, with 1 ISAPI filter (Url Rewrite) in front What I'm seeing during the load tests is that the requests all come through in bursts. Even though I have 7 different distributed clients sending traffic loads, the requests come through about 300-500 requests at a time. The performance monitor shows nearly all of the counters moving through this pattern, where a burst of requests comes in the req/sec jumps to 70, the queued requests jumps to 500, the current requests jumps up, the CPU jumps up, everything. Then once it's handled that group of requests, it has a lull for nearly 10 seconds where nearly nothing is happening. 0-5 req/sec, 0 queued requests, minimal CPU usage. Then after 10 seconds of inactivity, another burst comes through, spiking all of the counters once again. What I can't figure out is why the requests are coming through in bursts when I know that the load being generated is not sent that way, especially considering the various load-generating clients sending traffic all in different intervals with random think time's between each request. Is there something in the layers between Hyper-V or perhaps in the hardware which might cause this coalesce of requests together? Here is what i'm looking at, the highlighted metric is Requests/sec, but the others critical counter go with it: Requests Queued (which I'd obviously like to keep as close to 0 as possible). Any ideas on this?

  Read the article

• Flipping the video stream in Sony Vegas Studio!

  - by NoCanDo

  How do I flip a video stream, making it effectively appear to run backwards? For example, I've got a 6 second video stream. I cut it at 2, 4, 6, so I've got now 3 seperate streams with 2 seconds each. 1-2 ; 3-4; 5-6 - That's how it'll be displayed normally. Now what I want to do in Sony Vegas is to copy/paste and flip a selected stream. Let say: 1-2; 3-4; 3'-4'; 5-6 - The second 3-4 is copy/pasted; now I've got a video stream with 8 seconds. Now I want to flip this copy pasted making it effectively run backwards. 1-2; 3-4; 4'-3'; 5-6. The idea is I want something like a movie, it goes, and goes and goes, then a text appears "WAIT! What just happend?", then the movie goes back to second 3. 1-2-3-4-'WAIT! What just happened?'-4-3-4-5-6. I hope you get what I want to do in Sony Vegas.

  Read the article

• Filtered Router Interface

  - by jviotti

  I'm having some problems with a Scientific-Atlanta DPR2320R2. In specific with the WIFI. A few months ago I changed its password and username and now I can't remember. So I tried cracking it with Hydra but it drove things worse. Content of webadmin was rendered partial, and threw lot of errors. I then reseted the router. I found myself abled to browse the web with ethernet-connected pc. Wifi is configured by registering the device's MAC Address, and indeed the router has been reseted and register MAC address were lost. No device could connect to wifi. In fact, the device does not even recognize the network. I tried the pointing to 192.168.0.1 to restablish the MAC's. But I couldn't connect to the router access point. Tried listing up hosts: $ nmap -sP 192.168.0.0/24 Starting Nmap 5.00 ( http://nmap.org ) at 2012-12-11 01:18 ART Host 192.168.0.1 is up (0.0018s latency). Host 192.168.0.11 is up (0.00025s latency). Nmap done: 256 IP addresses (2 hosts up) scanned in 59.62 seconds Then checked 192.168.0.1 was really up by sending pings. It responded to all my pings. I quick-scanned the access point: $ nmap 192.168.0.1 Starting Nmap 5.00 ( http://nmap.org ) at 2012-12-11 01:08 ART Interesting ports on 192.168.0.1: Not shown: 999 closed ports PORT STATE SERVICE 80/tcp filtered http Nmap done: 1 IP address (1 host up) scanned in 6.73 seconds Look the state of the port 80: FILTERED. I'm pretty confused now. Any suggestion would be appreciated. Thanks in advance.

  Read the article

• Dual Monitor Setup with Ati Radeon Hd 5700 results in unusabledesktop win7

  - by NorthPole

  I have an ATI Radeon HD 5700 card which i've been using under fully updated windows 7 with its latest drivers. My monitor is a 2004 NEC LCD1703M which despite being pretty old runs fine. A friend gave me an IIYAMA ProLite E1900WS monitor (2009 or 20010 ). Both monitors are vga only. I've been using a DLDVI to VGA adapter to connect my old monitor and tested the same adapter to the new monitor and it worked fine. So I bought an HDMI to vga adapter with the purpose of having a dual monitor setup. But when both screens are connected to the card the following problem occurs: The monitor connected to the hdmi port cycles between sleep and a black screen while the other shows the operating system for about two seconds before getting black for another two seconds. I can "use" the computer (move the mouse,click,type e.t.c.) while this happens but its not something pleasant. I tried reinstalling the driver, booting with both screens connected (in which case the powerup messages and the bios are mirrored in both screens until I get to the login screen where everything falls apart) Funny thing is, everything works if I disconnect the ATI graphics card and use the onboard intel one. So, any suggestions as to what might be the problem and how I can fix it?

  Read the article

• Zabbix Proxy not collecting data

  - by syntaxcollector

  Hi All I have a working Zabbix 1.8.2 server collecting data for our office and our colo facility. However the link between the colo and office is flaky. What I'm trying to do is setup a proxy on the colo side to have a 1 hour cache and relay the data to our primary server at the office. Our zabbix server is compiled from source and uses a mysql database I've followed the instructions found in the zabbix documentation to compile the proxy using a sqlite3 database. I add the proxy to zabbix under Administration-DM-Proxies. The zabbix server "sees" the proxy because the "last seen" field is always under 60s. However when I assign a colo host to the proxy I stop receiving data from it. The colo host's zabbix_agentd.log file says this: 29343:20100622:124847 Timeout while answering request 29343:20100622:124847 Getting list of active checks failed. Will retry after 60 seconds The zabbix_proxy.log says this. 2041:20100622:123131.760 Deleted 0 records from history [0.000994 seconds] 2028:20100622:124131.671 Error while receiving answer from server [ZBX_TCP_READ() failed I also am unable to receive any SNMP data which is more important to me than the zabbix agent data. Has anyone had this problem before? Zabbix Server OS: CentOS5.4 Zabbix Server Build: 1.8.2 from source Zabbix Proxy OS: CentOS5.4 Zabbix Proxy Build: 1.8.2 from source P.S. The SQLite database on the zabbix proxy never gets any data written to it, it is identical to when I created it from the blank schema in zabbix-1.8.2/create/schema. (Yes I've checked the permissions)

  Read the article

• tail -f and then exit on matching string

  - by Patrick

  I am trying to configure a startup script which will startup tomcat, monitor the catalina.out for the string "Server startup", and then run another process. I have been trying various combinations of tail -f with grep and awk, but haven't got anything working yet. The main issue I am having seems to be with forcing the tail to die after grep or awk have matched the string. I have simplified to the following test case. test.sh is listed below: #!/bin/sh rm -f child.out ./child.sh > child.out & tail -f child.out | grep -q B child.sh is listed below: #!/bin/sh echo A sleep 20 echo B echo C sleep 40 echo D The behavior I am seeing is that grep exits after 20 seconds , however the tail will take a further 40 seconds to die. I understand why this is happening - tail will only notice that the pipe is gone when it writes to it which only happens when data gets appended to the file. This is compounded by the fact that tail is to be buffering the data and outputting the B and C characters as a single write (I confirmed this by strace). I have attempted to fix that with solutions I found elsewhere, such as using unbuffer command, but that didn't help. Anybody got any ideas for how to get this working how I expect it? Or ideas for waiting for successful Tomcat start (thinking about waiting for a TCP port to know it has started, but suspect that will become more complex that what I am trying to do now). I have managed to get it working with awk doing a "killall tail" on match, but I am not happy with that solution. Note I am trying to get this to work on RHEL4.

  Read the article

• Only one domains not resolving via Windows DNS server at multiple locations, but is at others

  - by Brett G

  I'm having quite a weird issue. Had mail delivery issues to a specific domain. After looking closer, I realized that the DNS for that domain isn't resolving via the in-house Windows 2003 SP2 DNS server. C:\>nslookup foodmix.net Server: DC.DOMAIN.com Address: 10.1.1.1 DNS request timed out. timeout was 2 seconds. DNS request timed out. timeout was 2 seconds. *** Request to DC.DOMAIN.com timed-out (DC.DOMAIN.com and 10.1.1.1 are generic values to replace the actual ones) Even if I run this nslookup from the DC.DOMAIN.com server, I get the same result. However, all other requests are working as they should. I tried it on severs at completely separate organizations on different networks(Windows 2003 AD servers). The weird thing is some of these were having the same exact issue. However using public DNS servers work. I have tried clearing the DNS cache, restarting the server, restarting the services, etc. Nothing has worked. One weird event I noticed in the DNS Server Event Logs that might be related is an event ID of 5504 with the following description: The DNS server encountered an invalid domain name in a packet from 192.33.4.12. The packet will be rejected. The event data contains the DNS packet. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. In the data section below, I can see the following mentioned: ns2.webhostingstar.com Which happens to be the nameserver for the domain in question. Several discussion threads and a MS KB have pointed to disabling EDNS. I have done this via "dnscmd /config /enableednsprobes 0" and it has not fixed the issue.

  Read the article

• Is there any limit to AIX 5.3 pipe size ?

  - by snowflake

  Hello, I'm in trouble while performing cat/tail/head operation on large files on Aix 5.3. When asking for a cat of several 1Go file redirected to another one: cat file1 file2 file3 > outputfile The outputfile is limited to 2Go (cat: output error and result file is 2147483647 bytes) Filesystem is jfs2. I successfully uploaded through ftp 10Go files on the filesystem without problem. I found nothing relevant in etc/security/limits: default: fsize = -1 core = 2097151 cpu = -1 data = 262144 rss = 65536 stack = 65536 nofiles = 20000 ulimit -a core file size (blocks) unlimited data seg size (kbytes) 245759 file size (blocks) unlimited max memory size (kbytes) unlimited open files 2000 pipe size (512 bytes) 64 stack size (kbytes) 32768 cpu time (seconds) unlimited max user processes 2048 virtual memory (kbytes) 278527 The problem does not occur on another AIX 5.3 server, I'm just looking for a different configuration that might be the source of the problem. /etc/security/limits on the server without the problem: default: fsize = -1 core = 2097151 cpu = -1 data = 262144 rss = 65536 stack = 65536 nofiles = 20000 ulimit -a on the server without the problem: core file size (blocks, -c) 1048575 data seg size (kbytes, -d) 131072 file size (blocks, -f) unlimited max memory size (kbytes, -m) 32768 open files (-n) 20000 pipe size (512 bytes, -p) 64 stack size (kbytes, -s) 32768 cpu time (seconds, -t) unlimited max user processes (-u) 262144 virtual memory (kbytes, -v) unlimited

  Read the article

• Windows 7 machine, can't connect remotely until after ping

  - by rjohnston

  I have a Windows 7 (Home Premium) machine that doubles as a media centre and subversion server. There's a couple of problems with this setup, when connecting to the server from an XP (SP3) machine: Firstly, the machine won't respond to it's machine name until after it's IP address has been pinged. Here's an example: Microsoft Windows XP [Version 5.1.2600] (C) Copyright 1985-2001 Microsoft Corp. C:\Documents and Settings\Rob>ping damascus Ping request could not find host damascus. Please check the name and try again. C:\Documents and Settings\Rob>ping 192.168.1.17 Pinging 192.168.1.17 with 32 bytes of data: Reply from 192.168.1.17: bytes=32 time=2ms TTL=128 ... Ping statistics for 192.168.1.17: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 1ms, Maximum = 2ms, Average = 1ms C:\Documents and Settings\Rob>ping damascus Pinging damascus [192.168.1.17] with 32 bytes of data: Reply from 192.168.1.17: bytes=32 time<1ms TTL=128 .... Ping statistics for 192.168.1.17: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 1ms, Average = 0ms C:\Documents and Settings\Rob> Likewise, subversion commands with either the machine name or IP address will fail until the machine's IP address is pinged. Occasionally, the machine won't respond to pings on it's IP address, it'll just come back with "Request timed out". The svn server is VisualSVN, if that helps... Any ideas?

  Read the article

• How do I fix a custom Event Viewer Log that merges automatically with the Application log?

  - by NightOwl888

  I am trying to create a custom event log for a Windows Service on Windows Server 2003. I would like to name the custom log "(ML) Startup Commands". However, when I add a registry key with that name to HKLM\SYSTEM\CurrentControlSet\Services\Eventlog\, it adds a log but shows the exact same events that are in the Application log when looking in the event viewer. If I add a registry key with the name "(ML) Startup Commands 2" to the event log, it shows a blank event log as expected. In fact, any other name will work correctly except for the one I want. I have searched through the registry for other keys with the string "(ML)" and removed all other references to this key name, however I continue to get merged results in the viewer when I create a key with this name. My question is, how can I fix the server so I can create a custom event log with this name that shows only the events from my application, not the events from the default Application event log that is installed with Windows? Update: I rebooted the server and woudn't you know it, the log started acting normally. I got a strange error message in the Application log: The EventSystem sub system is suppressing duplicate event log entries for a duration of 86400 seconds. The suppression timeout can be controlled by a REG_DWORD value named SuppressDuplicateDuration under the following registry key: HKLM\Software\Microsoft\EventSystem\EventLog. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. I can only hope this error doesn't mean the problem will come back after 86400 seconds. I guess I will have to wait and see.

  Read the article

• java.lang.OutOfMemoryError: unable to create new native thread

  - by Brad

  I consistently get this exception when trying to run my Junit tests on my mac: java.lang.OutOfMemoryError: unable to create new native thread at java.lang.Thread.start0(Native Method) at java.lang.Thread.start(Thread.java:658) at java.util.concurrent.ThreadPoolExecutor.addIfUnderMaximumPoolSize(ThreadPoolExecutor.java:727) at java.util.concurrent.ThreadPoolExecutor.execute(ThreadPoolExecutor.java:657) at java.util.concurrent.AbstractExecutorService.submit(AbstractExecutorService.java:92) at com.google.appengine.tools.development.ApiProxyLocalImpl$PrivilegedApiAction.run(ApiProxyLocalImpl.java:197) at com.google.appengine.tools.development.ApiProxyLocalImpl$PrivilegedApiAction.run(ApiProxyLocalImpl.java:184) at java.security.AccessController.doPrivileged(Native Method) at com.google.appengine.tools.development.ApiProxyLocalImpl.doAsyncCall(ApiProxyLocalImpl.java:172) at com.google.appengine.tools.development.ApiProxyLocalImpl.makeAsyncCall(ApiProxyLocalImpl.java:138) The same set of unit tests pass perfectly fine on ubuntu and windows. Some information about my system resources on the mac: $ ulimit -a core file size (blocks, -c) 0 data seg size (kbytes, -d) unlimited file size (blocks, -f) unlimited max locked memory (kbytes, -l) unlimited max memory size (kbytes, -m) unlimited open files (-n) 1024 pipe size (512 bytes, -p) 1 stack size (kbytes, -s) 8192 cpu time (seconds, -t) unlimited max user processes (-u) 266 virtual memory (kbytes, -v) unlimited $ java -version java version "1.6.0_24" Java(TM) SE Runtime Environment (build 1.6.0_24-b07-334-10M3326) Java HotSpot(TM) 64-Bit Server VM (build 19.1-b02-334, mixed mode) The reason I dont think this is an application issue is because the same tests pass in different environments. I have tried setting heap to 1024m, 512m and setting the stack to 64k and 128k (and each of these combinations) with no luck. My open files was originally 256 and I have bumped this to 1024. I have been googling around for a bit and all posts say to decrease heap size and increase stack size but that doesnt seem to help. Anyone have anymore ideas? EDIT: Here are is some environment information on my ubuntu box: $ ulimit -a core file size (blocks, -c) 0 data seg size (kbytes, -d) unlimited scheduling priority (-e) 20 file size (blocks, -f) unlimited pending signals (-i) 16382 max locked memory (kbytes, -l) 64 max memory size (kbytes, -m) unlimited open files (-n) 1024 pipe size (512 bytes, -p) 8 POSIX message queues (bytes, -q) 819200 real-time priority (-r) 0 stack size (kbytes, -s) 8192 cpu time (seconds, -t) unlimited max user processes (-u) unlimited virtual memory (kbytes, -v) unlimited file locks (-x) unlimited $ java -version java version "1.6.0_24" Java(TM) SE Runtime Environment (build 1.6.0_24-b07) Java HotSpot(TM) 64-Bit Server VM (build 19.1-b02, mixed mode)

  Read the article

• Comparing Nginx+PHP-FPM to Apache-mod_php

  - by Rushi

  I'm running Drupal and trying to figure out the best stack to serve it. Apache + mod_php or Nginx + PHP-FPM I used ApacheBench (ab) and Siege to test both setups and I'm seeing Apache performing better. This surprises me a little bit since I've heard a lot of good things about Nginx + PHP-FPM. My current Nginx setup is something that is a bit out of the box, and the same goes for PHP-FPM What optimizations I can make to speed up the Nginx + PHP-FPM combo over Apache and mo_php ? In my tests using ab, Apache is outperforming Nginx significantly (higher requets/second and finishing tests much faster) I've googled around a bit, but since I've never using Nginx, PHP-FPM or FastCGI, I don't exactly know where to start PHP v5.2.13, Drupal v6, latest PHP-FPM and Nginx compiled from source. Apache v2.0.63 ApacheBench Nginx + PHP-FPM Server Software: nginx/0.7.67 Server Hostname: test2.com Server Port: 80 Concurrency Level: 25 ---> Time taken for tests: 158.510008 seconds Complete requests: 1000 Failed requests: 0 Write errors: 0 ---> Requests per second: 6.31 [#/sec] (mean) Time per request: 3962.750 [ms] (mean) Time per request: 158.510 [ms] (mean, across all concurrent requests) Transfer rate: 181.38 [Kbytes/sec] received ApacheBench Apache using mod_php Server Software: Apache/2.0.63 Server Hostname: test1.com Server Port: 80 Concurrency Level: 25 --> Time taken for tests: 63.556663 seconds Complete requests: 1000 Failed requests: 0 Write errors: 0 --> Requests per second: 15.73 [#/sec] (mean) Time per request: 1588.917 [ms] (mean) Time per request: 63.557 [ms] (mean, across all concurrent requests) Transfer rate: 103.94 [Kbytes/sec] received

  Read the article

• Computer Comparison - which is "better"

  - by David Murdoch

  A company I work with recently replaced their old server and gave it to me. Their old server is a Dell PowerEdge 2600. I've been playing with the machine and even installed Windows Server 2008 on it...and it seems to run it pretty well. Here are the specs for the two machines: Dev Machine: AMD Athlon64 3000+ 2.38 GHz (overclocked from 1.8GHz [@ 280x8.5] - it is stable-ish) Memory (RAM): 1x1GB OCZ PC3200 (Dual-Channel) 300GB HD OS: Windows XP Pro (32bit) SuperPi 1M digit test: 40 seconds Dell PowerEdge 2600 Server: Intel Xeon CPU 2.8GHz 2.8GHz Memory (RAM): 512MBx2 (PC2700, not dual channel) 68GB HD (RAID 5) OS: Windows Server 2000 (32bit) SuperPi 1M digit test: 56 seconds [using 1 processor] (Themes and Aero-Flass UI turned off, of course) I use my computer to regularly run Photoshop CS5, Illustrator CS5, Flash CS5, 5 browsers (Chrome, FF, IE, Safari, Opera), iTunes, Visual Studio 2010, and Kaspersky Internet Security 2010 [sometimes simultaneously :-) ]. The SuperPi test has my dev machine coming in about 30% faster than the Server machine...though this could be due to the server running "Vista" with background processes prioritized. Do you think it would be realistic/advantageous for me to move from my dev machine to the Dell PowerEdge 2600? Is it possible to install additional DVD drives/burners on the server? Can I install my internal 300 GB hard drive on the server? Can I add some USB 2.0 ports? Note: I'll probably install Win XP Pro on the dev machine if I do switch. If not, are there any creative and useful way for me to take advantage of this server (with the goal of faster computing)?

  Read the article

• How to monitor changes in the frequency of network latency spikes over time?

  - by dequis

  I'm currently trying to troubleshoot an issue with my network in which I get latency spikes up to 200 seconds (normally around 50 secs) in an apparently random way at apparently random moments of the day. While trying to find what part of my messy network needs to be blamed (outside of the scope of this question - discussed a bit on chat), I realized I have no reliable way to confirm that a change actually improved anything. So far, the main way in which i notice this is that irssi shows [Lag: 15 (??)] in the statusbar, increasing every 5 seconds, and all other connections seem to be affected too. Since this depends on my observations, it's not a very reliable method to know how often it really happens. Note that just sending ICMP pings is probably not enough, but that's just my guess. It might be a "bufferbloat" issue, it might be packet loss, it might only apply to persistent connections. I suspect this because a few months ago, when the issue started, I had a "ping" command running in background and it didn't show anything weird at all during the latency spikes. This seems to have changed now (pings don't go through), but still, I'd prefer something more robust.

  Read the article

• MS DNS lookup issue

  - by 3molo

  Hi, Got two AD/DNS servers, and on the secondary I can't seem to lookup the external site www.iis.se (or any other hostname that their name servers control). The central firewall at this office allows any any outbound, tcp and udp. The DNS server has no local firewall nor antivirus. My windows client, located in the same subnet as the DNS server can do the lookup by asking the nameservers that are in control of www.iis.se. 'dig NS iis.se' shows iis.se. 2517 IN NS ns2.nic.se. iis.se. 2517 IN NS ns.nic.se. iis.se. 2517 IN NS ns3.nic.se. on AD/DNS server C:\Users\Administratornslookup www.iis.se 212.247.7.228 Server: UnKnown Address: 212.247.7.228 Name: www.iis.se Addresses: 2a00:801:f0:80::80 212.247.7.221 C:\Users\Administratornslookup www.iis.se 194.17.45.54 Server: UnKnown Address: 194.17.45.54 Name: www.iis.se Addresses: 2a00:801:f0:80::80 212.247.7.221 C:\Users\Administratornslookup www.iis.se 212.247.3.83 Server: UnKnown Address: 212.247.3.83 Name: www.iis.se Addresses: 2a00:801:f0:80::80 212.247.7.221 And still: C:\Users\administratornslookup www.iis.se Server: UnKnown Address: 127.0.0.1 DNS request timed out. timeout was 2 seconds. DNS request timed out. timeout was 2 seconds. * Request to UnKnown timed-out

  Read the article

< Previous Page | 53 54 55 56 57 58 59 60 61 62 63 64  | Next Page >