Search Results

Search found 2475 results on 99 pages for 'vmware vsphere'.

Page 57/99 | < Previous Page | 53 54 55 56 57 58 59 60 61 62 63 64  | Next Page >

  • Disk IO slow on ESXi, even slower on a VM (freeNAS + iSCSI)

    - by varesa
    I have a server with ESXi 5 and iSCSI attached network storage(4x1Tb Raid-Z on freenas 8.0.4). Those two machines are connected to each other with Gigabit ethernet. The raid-z volume is divided into three parts: two zvols, shared with iscsi, and one directly on top of zfs, shared with nfs and similar. I ssh'd into the freeNAS box, and did some testing on the disks. I used ddto test the third part of the disks (straight on top of ZFS). I copied a 4GB (2x the amount of RAM) block from /dev/zero to the disk, and the speed was 80MB/s. Other of the iSCSI shared zvols is a datastore for the ESXi. I did similar test with time dd .. there. Since the dd there did not give the speed, I divided the amount of data transfered by the time show by time. The result was around 30-40 MB/s. Thats about half of the speed from the freeNAS host! Then I tested the IO on a VM running on the same ESXi host. The VM was a light CentOS 6.0 machine, which was not really doing anything else at that time. There were no other VMs running on the server at the time, and the other two "parts" of the disk array were not used. A similar dd test gave me result of about 15-20 MB/s. That is again about half of the result on a lower level! Of course the is some overhead in raid-z - zfs - zvolume - iSCSI - VMFS - VM, but I don't expect it to be that big. I belive there must be something wrong in my system. I have heard about bad performance of freeNAS's iSCSI, is that it? I have not managed to get any other "big" SAN OS to run on the box (NexentaSTOR, openfiler). Can you see any obvious problems with my setup?

    Read the article

  • Troubleshooting latency spikes on ESXi NFS datastores

    - by exo_cw
    I'm experiencing fsync latencies of around five seconds on NFS datastores in ESXi, triggered by certain VMs. I suspect this might be caused by VMs using NCQ/TCQ, as this does not happen with virtual IDE drives. This can be reproduced using fsync-tester (by Ted Ts'o) and ioping. For example using a Grml live system with a 8GB disk: Linux 2.6.33-grml64: root@dynip211 /mnt/sda # ./fsync-tester fsync time: 5.0391 fsync time: 5.0438 fsync time: 5.0300 fsync time: 0.0231 fsync time: 0.0243 fsync time: 5.0382 fsync time: 5.0400 [... goes on like this ...] That is 5 seconds, not milliseconds. This is even creating IO-latencies on a different VM running on the same host and datastore: root@grml /mnt/sda/ioping-0.5 # ./ioping -i 0.3 -p 20 . 4096 bytes from . (reiserfs /dev/sda): request=1 time=7.2 ms 4096 bytes from . (reiserfs /dev/sda): request=2 time=0.9 ms 4096 bytes from . (reiserfs /dev/sda): request=3 time=0.9 ms 4096 bytes from . (reiserfs /dev/sda): request=4 time=0.9 ms 4096 bytes from . (reiserfs /dev/sda): request=5 time=4809.0 ms 4096 bytes from . (reiserfs /dev/sda): request=6 time=1.0 ms 4096 bytes from . (reiserfs /dev/sda): request=7 time=1.2 ms 4096 bytes from . (reiserfs /dev/sda): request=8 time=1.1 ms 4096 bytes from . (reiserfs /dev/sda): request=9 time=1.3 ms 4096 bytes from . (reiserfs /dev/sda): request=10 time=1.2 ms 4096 bytes from . (reiserfs /dev/sda): request=11 time=1.0 ms 4096 bytes from . (reiserfs /dev/sda): request=12 time=4950.0 ms When I move the first VM to local storage it looks perfectly normal: root@dynip211 /mnt/sda # ./fsync-tester fsync time: 0.0191 fsync time: 0.0201 fsync time: 0.0203 fsync time: 0.0206 fsync time: 0.0192 fsync time: 0.0231 fsync time: 0.0201 [... tried that for one hour: no spike ...] Things I've tried that made no difference: Tested several ESXi Builds: 381591, 348481, 260247 Tested on different hardware, different Intel and AMD boxes Tested with different NFS servers, all show the same behavior: OpenIndiana b147 (ZFS sync always or disabled: no difference) OpenIndiana b148 (ZFS sync always or disabled: no difference) Linux 2.6.32 (sync or async: no difference) It makes no difference if the NFS server is on the same machine (as a virtual storage appliance) or on a different host Guest OS tested, showing problems: Windows 7 64 Bit (using CrystalDiskMark, latency spikes happen mostly during preparing phase) Linux 2.6.32 (fsync-tester + ioping) Linux 2.6.38 (fsync-tester + ioping) I could not reproduce this problem on Linux 2.6.18 VMs. Another workaround is to use virtual IDE disks (vs SCSI/SAS), but that is limiting performance and the number of drives per VM. Update 2011-06-30: The latency spikes seem to happen more often if the application writes in multiple small blocks before fsync. For example fsync-tester does this (strace output): pwrite(3, "aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa"..., 1048576, 0) = 1048576 fsync(3) = 0 ioping does this while preparing the file: [lots of pwrites] pwrite(3, "********************************"..., 4096, 1036288) = 4096 pwrite(3, "********************************"..., 4096, 1040384) = 4096 pwrite(3, "********************************"..., 4096, 1044480) = 4096 fsync(3) = 0 The setup phase of ioping almost always hangs, while fsync-tester sometimes works fine. Is someone capable of updating fsync-tester to write multiple small blocks? My C skills suck ;) Update 2011-07-02: This problem does not occur with iSCSI. I tried this with the OpenIndiana COMSTAR iSCSI server. But iSCSI does not give you easy access to the VMDK files so you can move them between hosts with snapshots and rsync. Update 2011-07-06: This is part of a wireshark capture, captured by a third VM on the same vSwitch. This all happens on the same host, no physical network involved. I've started ioping around time 20. There were no packets sent until the five second delay was over: No. Time Source Destination Protocol Info 1082 16.164096 192.168.250.10 192.168.250.20 NFS V3 WRITE Call (Reply In 1085), FH:0x3eb56466 Offset:0 Len:84 FILE_SYNC 1083 16.164112 192.168.250.10 192.168.250.20 NFS V3 WRITE Call (Reply In 1086), FH:0x3eb56f66 Offset:0 Len:84 FILE_SYNC 1084 16.166060 192.168.250.20 192.168.250.10 TCP nfs > iclcnet-locate [ACK] Seq=445 Ack=1057 Win=32806 Len=0 TSV=432016 TSER=769110 1085 16.167678 192.168.250.20 192.168.250.10 NFS V3 WRITE Reply (Call In 1082) Len:84 FILE_SYNC 1086 16.168280 192.168.250.20 192.168.250.10 NFS V3 WRITE Reply (Call In 1083) Len:84 FILE_SYNC 1087 16.168417 192.168.250.10 192.168.250.20 TCP iclcnet-locate > nfs [ACK] Seq=1057 Ack=773 Win=4163 Len=0 TSV=769110 TSER=432016 1088 23.163028 192.168.250.10 192.168.250.20 NFS V3 GETATTR Call (Reply In 1089), FH:0x0bb04963 1089 23.164541 192.168.250.20 192.168.250.10 NFS V3 GETATTR Reply (Call In 1088) Directory mode:0777 uid:0 gid:0 1090 23.274252 192.168.250.10 192.168.250.20 TCP iclcnet-locate > nfs [ACK] Seq=1185 Ack=889 Win=4163 Len=0 TSV=769821 TSER=432716 1091 24.924188 192.168.250.10 192.168.250.20 RPC Continuation 1092 24.924210 192.168.250.10 192.168.250.20 RPC Continuation 1093 24.924216 192.168.250.10 192.168.250.20 RPC Continuation 1094 24.924225 192.168.250.10 192.168.250.20 RPC Continuation 1095 24.924555 192.168.250.20 192.168.250.10 TCP nfs > iclcnet_svinfo [ACK] Seq=6893 Ack=1118613 Win=32625 Len=0 TSV=432892 TSER=769986 1096 24.924626 192.168.250.10 192.168.250.20 RPC Continuation 1097 24.924635 192.168.250.10 192.168.250.20 RPC Continuation 1098 24.924643 192.168.250.10 192.168.250.20 RPC Continuation 1099 24.924649 192.168.250.10 192.168.250.20 RPC Continuation 1100 24.924653 192.168.250.10 192.168.250.20 RPC Continuation 2nd Update 2011-07-06: There seems to be some influence from TCP window sizes. I was not able to reproduce this problem using FreeNAS (based on FreeBSD) as a NFS server. The wireshark captures showed TCP window updates to 29127 bytes in regular intervals. I did not see them with OpenIndiana, which uses larger window sizes by default. I can no longer reproduce this problem if I set the following options in OpenIndiana and restart the NFS server: ndd -set /dev/tcp tcp_recv_hiwat 8192 # default is 128000 ndd -set /dev/tcp tcp_max_buf 1048575 # default is 1048576 But this kills performance: Writing from /dev/zero to a file with dd_rescue goes from 170MB/s to 80MB/s. Update 2011-07-07: I've uploaded this tcpdump capture (can be analyzed with wireshark). In this case 192.168.250.2 is the NFS server (OpenIndiana b148) and 192.168.250.10 is the ESXi host. Things I've tested during this capture: Started "ioping -w 5 -i 0.2 ." at time 30, 5 second hang in setup, completed at time 40. Started "ioping -w 5 -i 0.2 ." at time 60, 5 second hang in setup, completed at time 70. Started "fsync-tester" at time 90, with the following output, stopped at time 120: fsync time: 0.0248 fsync time: 5.0197 fsync time: 5.0287 fsync time: 5.0242 fsync time: 5.0225 fsync time: 0.0209 2nd Update 2011-07-07: Tested another NFS server VM, this time NexentaStor 3.0.5 community edition: Shows the same problems. Update 2011-07-31: I can also reproduce this problem on the new ESXi build 4.1.0.433742.

    Read the article

  • VMXNET3 nic loses the ability to update ARP table after N hours

    - by Peter
    I have a fedora 18 VM that stops updating the arp table on eth1 after running for a number of hours to days. There are other VMs on the same hypervisor that can access all of the same networks without issue. A tcpdump of the offending NIC shows only ARP broadcasts but no responses. None of the other VMs on the vDS see the ARP broadcasts from the offending NIC. The only way I can currently solve the problem is to reboot the VM and then everything works for a while. I've tried changing the port on the vDS and even flipping the network configurations after I lose eth1's ARP table, but the ARP problem follows eth1 but I can access the machines that were originally on eth1. If I statically add the arp entries for machines on the same subnet I have no problems with connectivity. The Hypervisor is an HP BL49X series with flex-10 network modules. Has anyone seen anything like this before?

    Read the article

  • Is it possible to boot from a passthrough lsi2008 under esxi?

    - by Kurt
    I currently have Solaris 11 Express running on bare metal. I'd like to convert the machine to an ESXI host and run the existing os as a virtual machine. I have ESXI setup, the virtual machine made, if I boot the vm from the recovery disk the drives and lsi2008 controller is visible. Everything looks like it should work, but the vm bios does not seem to try and boot from the controller. Is this just impossible?

    Read the article

  • Executing Secondary Applications

    - by JooBlow
    I have an application I am attempting to make "portable". The application contains a lot of secondary utility functions that I would like to execute on external files(from the app). I tried adding them in the build process but I didn't get any "Executables" for them(just the main one and a few others). Is there a way to get these to excute? They are basically command line utility functions to process some text files but use large files in the distribution and are also used by the main application. Thanks

    Read the article

  • acessing a subnetwork from within a vm

    - by yan bellavance
    I have a pc running windows 7. I have vmwareplayer running RHEL5 I have 1 physical ethernet connection. this ethernet connection is wired to a hub. there is another device on that hub that needs to be in a certain subnetwork (192.168.0.xxx)(lets call him device X) but the general network is 192.168.1.xxx How can I configure the network adapters so that I can ping device X from RHEL5 in the vm. Originally I could ping google from both windows and rhel (I was in the .1 network) but not device X since he is on a different subnetwork address. Now that I have put it on the .0 I can ping device X from windows but not from rhel5 and cannot access the web. I did this by manually setting the IP address.

    Read the article

  • How-to make "ghost" of existing user in lab manager?

    - by clevi
    We have an automation process which undeploys specific configuration on LM every night. this process also deploy the configuration at morning. The problem is that this process works as admin so all this configs deployed by admin, which means sometimes they deployed on "reserved" resources pool. I want to try to impersonate a user on Lab Manager so the configuration will be deployed by the user owned this machine, and not by admin. does anyone has any idea how to do so?

    Read the article

  • Installing ubuntu via VMWare Player

    - by c0mrade
    Hi everyone, I've just installed the latest 32bit ubuntu on a WMware Player and I was prompted for username/password I wrote mine , now I've been asked ubuntu login I keep missing I get error message Login incorrect with I login and password I use from the setup, is there a default password out there, what do I do now ?

    Read the article

  • diskpart on RDM's ...

    - by karnash
    HI, We have ESXi cluster which is attached to clariion CX4 We have windows 2008 R2 as the guest OS. Attahed to this vm is 2 x 1.95T RDM's I select disk 1 create partition primary size=1 (1MB) then list partition Partition ### Type Size Offset * Partition 1 Primary 1024 KB 1024 KB Then I do the same for the other disk and offset is 1024KB I need to present 4T disk to this vm so I right click on disk 1 convert to simple volume then extend it by adding the second disk now when I do list partition, I see the off set is set to 31k. Can anyone please guide me. Thanks

    Read the article

  • multiple VM vs multiple named instance

    - by thushya
    Hi , I am looking for some comparison or data for sql 2008 deployment , what are the advantages and disadvantages installing multiple VM vs multiple named instance ? How can i save license cost using VMs vs physical server for sql 2008 ? is there a way to find out what is maximum number of connections to database at any time or in the past - need to calculate needed CAL license ? Thanks.

    Read the article

  • Why the OS in VM always blue screen by chance ?

    - by Foolish
    it always has this error :driver_irql_not_less_or_equal And as i searched over the internet, I found it might because of the bridged network card problem, it would be OK if i changed to NAT.(but I am not sure) And after I reduce the memory allocated to the VM, the error didn't occurs till now Is there any solution?

    Read the article

  • Issues with creating a snapshot

    - by Andy Welcomer
    Hello everyone, We have a strange issue when attempting to create a snapshot in one of our regional environments. We have 4 VMs, 2 of them have mulitple VMDKs spread onto different datastores. When a snapshot is created, all the VMDKs (except for the first), seem to vanish. If you look at the properties of the VM, the path to the VMDKS points to the datastore where the primary VMDK is, and the file name is some random garbage. If the snapshot is deleted everything returns to normal. Has anyone ever seen this? I'm using ESX3.5 Thank you in advance. Andy ==============UPDATE============== Here is some more information. I just created a test machine with 7 VMDKs. 1 for the OS. and 6 others for data. All of the VMDKs are in seperate datastores. I take a snapshot of the machine, all of the 6 VMDKs loose their reference to the actual VMDK files. The all point to 64KB VMDK files in the datastore where the OS VMDK is located. These 64KB vmdks didn't exist until the snapshot was taken. When the snapshot is deleted, everything goes back to normal.

    Read the article

  • Where can I download copies of a Windows XP ISO image with Internet Explorer 6 or Internet Explorer 7 for VirtualBox?

    - by Andrew Arrow
    I have Windows 7 Professional hosting Ubuntu inside VirtualBox for my development machine. To test my site, I run Internet Explorer and hit my Ubuntu box. This works great for Internet Explorer 8, the default browser on this Windows machine. I also want to run another VM with a copy of Windows XP with Internet Explorer 6 or Internet Explorer 7. Where can I download ISO image files of old copies of Windows XP? I've looked in Internet Explorer Application Compatibility VPC Image and these only run in Virtual PC/XP Mode which won't run while VirtualBox is running. If I have to run VirtualBox (can't work without Ubuntu running the site), is there any way to test Internet Explorer 6, Internet Explorer 7, and Internet Explorer 8 from the same Windows 7 machine?

    Read the article

  • Fusion 2 - blank screen - no start button

    - by KDK2010
    I have Fusion 2 on my MacBook. It was working fine until this morning. Logged on and it took too long to log my personal settings to load. I shut it down. Shut down the MacBook and restarted. Logged onto Fusion and now I only get the windows screen with no icons or Start Button. I don't want to uninstall in fear of loosing all of my work including Quickbooks! Anyone have a solution?

    Read the article

  • File Not Found error launching Guest OS in a non-administrator user account

    - by ToreTrygg
    Hi, I am running Fusion 2.0.6 (196839) on an iMac running 10.6.2 with 3 user accounts (1 Administrator). I have Fusion set up to share the Guest OS, and it's been working splendidly for nearly a year. Within the Guest OS (Windows XP PRO), there are also 3 user accounts (1 Administrator). Last night I went to back up my VM to an external drive, and to minimize the file size and transfer time, I deleted all Snapshots but the most-recent one. I then backed up the VM externally (28.23 GB). Today, one of my users tried to launch the Guest OS from within her user account, and received the following error message: "File Not Found: Windows XP Pro-000006.vmdk "This file is required to power on this virtual machine. If this file was moved, please provide its new location." My two choices are Cancel and Browse. When I browse, I can locate the Windows XP Pro-000006.vmdk file, which appears to be contained within the VM file (Windows XP Pro.vmwarevm). However, it still won't launch from a non-Admin user account. If I view the package contents of the VM file from the user account, the above file is present and appears to be created upon each launch of the Guest OS. If I go back to my Administrator account on the Mac and then launch Fusion, the Guest OS works perfectly for all 3 user accounts within XP Pro. I have tried to delete the Guest OS from Fusion's Library within the problem user account, then re-connect it to that Library, but the result is the same. The Guest OS data integrity is 100% -- but is accessible only from the OS X Administrator account. This problem only surfaced after deleting several older Snapshots. Again, the data is there, the Guest OS powers up normally in the Mac's Administrator account, but persistently returns the above error when attempting to power on from a non-Admin account on the Mac. I'm not sure how this is affecting the error, but when I look at Hard Disk Settings, the "unable-to-locate" file is the filename of the virtual HD. I don't want to make any changes to my (working) VM without any advice from the knowledgeable people on this forum. Any help will be greatly appreciated, thanks!

    Read the article

  • Service Console Logs

    - by Anky123
    Hi, i have been workin on ESX3 and 3.5 but never came accross these logs. Now i want to know how to read such logs and what are the different logs i can see from /var/logs i tried to read "messages" logs for service console, but could not recollect much. Also at what point these different logs are useful for common problems on ESX where we can refer thses logs. Please let me know...

    Read the article

  • ESXi 4.0 Licensing Limits

    - by Ramsey
    From what I understand, the software is free and you just need to register to remove the 60-day limitation. Does this mean I have to register every time I install ESXi on a new machine? Or can I use the same key for different ESXi 4.0 installations?

    Read the article

  • Small Business HP Virtualisation and iSCSI SAN Options

    - by Robin Day
    We are a small business that hosts our core product on a number of HP servers. Our core production setup is 1x HP DL380, high powered for a SQL Server Database 1x HP DL360, mid powered for our core application server 6x HP DL320, low powered for our front ends We run our training / testing / support systems on a similar setup, the servers are just older and less powerful. Unfortunately this is now causing us issues as the system has grown beyond the capabilities of these older servers. Upgrading these servers would be expensive and we believe that virtualisation is probably the way to go for the future. Locally we run a number of test / dev environments on ESXi using Direct Storoage on a couple of high powered DL360's and these are performing fairly well. We're thinking that instead of replacing all of our test servers that we can implement an iSCSI SAN and one or two high powered hosts. Hopefully looking that when it comes to replace our live servers as well that we can just expand the virual environment to cope. So my question is... Can anyone offer any advice on some suitable options? We have generally always been extremely happy with HP servers, all of our kit is currently HP, therefore our preference would be to stick with HP, however, I'm always happy to hear about other options. I'm hoping that initially a budget of around 15-25k (GBP) would be suitable, this could potentially be increased if I had confidence that the system would pave the way for a cost effective upgrade of our live systems in the future as well. I am new to SAN's and my only real experience is playing with OpenFiler on some old desktops. I think iSCSI should be suitable, but I've not done any research into how SQL server may perform. I've had a browser through HP's sites and see plenty of information about EVA, MSA, LeftHand, etc. However, from looking at all that, I don't see which options would be best and more importantly I don't know exactly what I would need to buy. Any help, links, opinions would be much appreciated. Thanks

    Read the article

  • Cannot increase Datastore

    - by k4w4zz
    Hello, We have an ESX 4.0 cluster with 2 hosts, EMC Clarion SAN storage with 10 LUNs. We have added 2 new 400 GB LUNs. All the LUNs are visible from both hosts. I have extended an existing 500 GB datastore with one of these 400 GB LUNs - the new datastore size is now 900 GB. I'd like to do the same operation with the second 400 GB LUN to extend another existing datastore but I'm not able to do it. The LUN is available to create a brand new datastore but is not visible to extend an existing one. I don't understand why everything was fine with the other one and why can't I do the same exact operation with this LUN. The result is the same on both hosts. The SAN admin have erased and re-created several times this LUN. I have rescan the HBA each time. In attachment you can find the result of the esxcfg-mpath -l and fdisk -l commands on both servers. Does somebody have an idea please?

    Read the article

  • IBM X3200 M2 upgrade and VT-x / usb passthrough for esxi

    - by enzo
    Hi, I have an IBM server x3200 m2 4368-k1g. Only to understand, simply because on IBM support does not exist no more upgrades kit on sale... if I buy a xeon processor, for example x3330 (4core @ 2.6ghz), and put it on my motherboard... 1) it works? 2) on the bios (where now there is no trace about...) will compare a VT-x menu to select and enable? 3) with esxi, once the VT-x is on... I'll be able to have usb passthrough ? Thank you in advance for your reply

    Read the article

  • What does this mean: "SATP VMW_SATP_LOCAL does not support device configuration"?

    - by Jason Tan
    Can anyone tell me what this means in ESXi 5.1?: SATP VMW_SATP_LOCAL does not support device configuration I've googled it and I get a lot of results, but as yet all the pages that contain the string are discussing other matters. The storage array is a HDS HUS-VM and the hosts are HP b460c G8 blades with flex fabric and flex fabric VCs which I am in the process of commissioning and would like to get it started on the right foot - i.e. error and warning free! naa.600508b1001c56ee3d70da65f071da23 Device Display Name: HP Serial Attached SCSI Disk (naa.600508b1001c56ee3d70da65f071da23) Storage Array Type: VMW_SATP_LOCAL Storage Array Type Device Config: SATP VMW_SATP_LOCAL does not support device configuration. Path Selection Policy: VMW_PSP_FIXED Path Selection Policy Device Config: {preferred=vmhba0:C0:T0:L1;current=vmhba0:C0:T0:L1} Path Selection Policy Device Custom Config: Working Paths: vmhba0:C0:T0:L1 Is Local SAS Device: true Is Boot USB Device: false This is the same LUN: ~ # esxcli storage core device list -d naa.60060e80132757005020275700000016 naa.60060e80132757005020275700000016 Display Name: HITACHI Fibre Channel Disk (naa.60060e80132757005020275700000016) Has Settable Display Name: true Size: 204800 Device Type: Direct-Access Multipath Plugin: NMP Devfs Path: /vmfs/devices/disks/naa.60060e80132757005020275700000016 Vendor: HITACHI Model: OPEN-V Revision: 5001 SCSI Level: 2 Is Pseudo: false Status: degraded Is RDM Capable: true Is Local: false Is Removable: false Is SSD: false Is Offline: false Is Perennially Reserved: false Queue Full Sample Size: 0 Queue Full Threshold: 0 Thin Provisioning Status: unknown Attached Filters: VAAI_FILTER VAAI Status: supported Other UIDs: vml.020001000060060e801327570050202757000000164f50454e2d56 Is Local SAS Device: false Is Boot USB Device: false ~ #

    Read the article

  • re-point LM to a new vCenter (share same database)

    - by CapiZikus
    1) I'm planning to create a new vCenter server which database point to the same db as current vCenter (the one LM pointing to atm), Then I'm planning to repoint the LM to a new vCenter, ( the new one will see the same esx host, datastore, etc) Is LM will be okay if I do this? 2) The currect VC is a dediated server and a new vCenter will be VM, the current vCenter has database installed on local machine (inc update manager as well) I'm planning to move the local db to cluster db then point the current vCenter to this new cluster and make sure everything is working before promote a new one. Update manager will also has it own VM and point to a new db cluster. Is anythingelse I miss out or need to pay more attention on? thanks

    Read the article

  • Recovery files from a damage VM?

    - by ejlml
    After search and search again, my VM still can't recovery. Does somebody know how to retrieve the files from the VM? My VM is XP, it can't boot up anymore after my forced quit. In the Mac OS 10.6.2, I try to "get info" the VM file, I can see it is still using 25G space. I try to mount it with VMDK mounter (just right click the VM file and chose open with), it can mount but nothing inside. I also try to use filesalvage to recovery the files after mounted the VM, it can recovery many many files, but the files name and some document become to be symbol. What can I do now? Pls help me, thanks!

    Read the article

< Previous Page | 53 54 55 56 57 58 59 60 61 62 63 64  | Next Page >