Search Results

Search found 24931 results on 998 pages for 'information visualization'.

Page 570/998 | < Previous Page | 566 567 568 569 570 571 572 573 574 575 576 577  | Next Page >

• Cisco access list logging. Why is there a difference between IPv4 and IPv6?

  - by growse

  I've got a Cisco 877 router. I've got an IPv4 access list and an IPv6 access list set up and configured similar to this: interface Dialer1 ... ip access-group INTERET-IN ipv6 traffic-filter IPV6-IN Each of these access lists has a final rule of deny ip/ipv6 any any log. However, in my syslog I notice that there's a difference in formatting between the two types of entries. IPv4 will say: %SEC-6-IPACCESSLOGP: list INTERNET-IN denied udp 88.89.209.63(137) -> 1.2.3.4(137), 1 packet Whereas the IPv6 list will say %IPV6_ACL-6-ACCESSLOGNP: list IPV6-IN/240 denied 59 2001:0:5EF5:79FD:14F9:B773:3EBA:3EE3 (Dialer1) -> 2001:800:1000:0::1, 8 packets Both have broadly the same information, but the IPv6 log entry is missing the protocol type and port, both of which are very useful if I'm trying to troubleshoot connectivity. Why is this? How do I get IPv6 deny logs to display the protocol and port used, if any?

  Read the article

• Slow Inserts SQL Server 2005

  - by Achilles

  I'm researching an issue with the following information: We had a logging table with about 90k records in it that had inserts taking several seconds(approximately 10 to 20s) in extreme cases. One of the columns of the table stores XML as the XML datatype. The XML isn't being parsed during the insert, just stored. We tried truncating the table assuming that the issue was related the number of records(althought 90k seemed "normal") and the inserts still are performing poorly. While I know there are other issues that can cloud the issue, what would be some "check this first" ideas that could help me debug this issue? Thanks for any suggestions and help in advance.

  Read the article

• Kickstart Partitioning Configuration

  - by Flo

  I'be been trying to run a kickstart script with the following partition configuration: #Clear the masterboot record zerombr bootloader --location=mbr --driveorder=sda --append=" rhgb crashkernel=auto quiet" # Set up the partitions/logical volumes/logical groups clearpart --all part /boot --fstype=ext4 --asprimary --size=512 --ondisk=sda part swap --size=2048 --fstype=swap --ondisk=sda part pv.01 --fstype=ext4 --grow --size=200 --ondisk=sda part pv.02 --fstype=ext4 --grow --size=200 --ondisk=sdb volgroup VolGroup pv.01 pv.02 --pesize=32768 logvol /opt --fstype=ext4 --name=opt.fs --vgname=VolGroup --size=40000 logvol / --fstype=ext4 --name=root.fs --vgname=VolGroup --size=78000 I have two hard drives and it looks to me like its a really simple configuration. When I run the kickstart I keep getting all these errors that have to do with python files for configuring partitions. The only actual maybe useful piece of information is KeyError /dev/sda/ I tried a number of alterations of this configuration but nothing really worked. Any ideas?

  Read the article

• Software for a online collaborative bi/tri lingual dictionary [closed]

  - by user537488

  I am looking for a software which I can host in popular and general shared web hosting services(online softwares like wordpress, meidawiki, drupal etc.) which can do the following- allow users to create account allow users or anons to add words to the dictionary (there will be English as base language and other languages) easier way to import all the words from English dictionary users should be able to write the that language equivalent of the English word Every word should have it's own address and page like www.namesomething.com/word/en/software will contain the word software and the other language word for it search should be faster and should find nearer results it's should be able to list related words like if the user is looking at "software" then other words from s like "softcopy" etc should appear alphabetically in that page Any one should be able to comment on the word which is not seen in the main page but other page similar to the talk page in the wiki any one should be able to contribute clean interface unlike wiki (media wiki and all other) just for words only I tried media wiki and other wiki software but it overloaded and unclean. I am looking for interface similar to oed.com but clean, minimal as we are not going to have such more information. Just words in English and it's other language equivalent. Here we are talking about a language which has not yet been in the Internet. It's should be collaborative.

  Read the article

• Powershell and DfsrConfigurationFromAD - how to check all servers are updated?

  - by user57792

  I have two Win2012R2 servers (SERVER1 and SERVER2) that uses DFS Replication for keeping a couple of folders synchronized. Using the following Powershell-script that i run on SERVER1 I disconnect it from the group: Set-DfsrConnection -GroupName "Group1" -SourceComputerName "SERVER1" -DestinationComputerName "SERVER2" -DisableConnection $True; And to update both the servers with the configuration I run the command: Update-DfsrConfigurationFromAD -ComputerName "SERVER1","SERVER2" Now the question is, how can check on SERVER1 that SERVER2 has gotten the updated information from the AD so that I can be sure that the connection has been disabled? Usually it takes around 10-30 seconds after the Update-DfsrConfigurationFromAD command has been run before the DFS Management on SERVER2 gets updated but I need some kind of a "check and sleep loop" in my code. I've tried checking event logs and using Invoke-Command {Get-DfsrConnection} from PM-SERVER01 but nothing seems to work.

  Read the article

• What is a 'good number' of exceptions to implement for my library?

  - by Fuzz

  I've always wondered how many different exception classes I should implement and throw for various pieces of my software. My particular development is usually C++/C#/Java related, but I believe this is a question for all languages. I want to understand what is a good number of different exceptions to throw, and what the developer community expect of a good library. The trade-offs I see include: More exception classes can allow very fine grain levels of error handling for API users (prone to user configuration or data errors, or files not being found) More exception classes allows error specific information to be embedded in the exception, rather than just a string message or error code More exception classes can mean more code maintenance More exception classes can mean the API is less approachable to users The scenarios I wish to understand exception usage in include: During 'configuration' stage, which might include loading files or setting parameters During an 'operation' type phase where the library might be running tasks and doing some work, perhaps in another thread Other patterns of error reporting without using exceptions, or less exceptions (as a comparison) might include: Less exceptions, but embedding an error code that can be used as a lookup Returning error codes and flags directly from functions (sometimes not possible from threads) Implemented an event or callback system upon error (avoids stack unwinding) As developers, what do you prefer to see? If there are MANY exceptions, do you bother error handling them separately anyway? Do you have a preference for error handling types depending on the stage of operation?

  Read the article

• Is this table replicated?

  - by fatherjack

  Another in the potentially quite sporadic series of I need to do ... but I cant find it on the internet. I have a table that I think might be involved in replication but I don't know which publication its in... We know the table name - 'MyTable' We have replication running on our server and its replicating our database, or part of it - 'MyDatabase'. We need to know if the table is replicated and if so which publication is going to need to be reviewed if we make changes to the table. How? USE MyDatabase GO /* Lots of info about our table but not much that's relevant to our current requirements*/ SELECT * FROM sysobjects WHERE NAME = 'MyTable' -- mmmm, getting there /* To quote BOL - "Contains one row for each merge article defined in the local database. This table is stored in the publication database.replication" interesting column is [pubid] */ SELECT * FROM dbo.sysmergearticles AS s WHERE NAME = 'MyTable' -- really close now /* the sysmergepublications table - Contains one row for each merge publication defined in the database. This table is stored in the publication and subscription databases. so this would be where we get the publication details */ SELECT * FROM dbo.sysmergepublications AS s WHERE s.pubid = '2876BBD8-3D4E-4ED8-88F3-581A659E8144' -- DONE IT. /* Combine the two tables above and we get the information we need */ SELECT s.[name] AS [Publication name] FROM dbo.sysmergepublications AS s INNER JOIN dbo.sysmergearticles AS s2 ON s.pubid = s2.pubid WHERE s2.NAME = 'MyTable' So I now know which

  Read the article

• Fault Handling Slides and Q&A by Vennester

  - by JuergenKress

  Fault Handling It is one thing to architect, design, and code the “happy flow” of your automated business processes and services. It is another thing to deal with situations you do not want or expect to occur in your processes and services. This session dives into fault handling in Oracle Service Bus 11g and Oracle SOA Suite 11g, based on an order-to-cash business process. Faults can be divided into business faults, technical faults, programming errors, and faulty user input. Each type of fault needs a different approach to prevent them from occurring or to deal with them. For example, apply User Experience (UX) techniques to improve the quality of your application so that faulty user input can be prevented as much as possible. This session shows and demos what patterns and techniques can be used in Oracle Service Bus and Oracle SOA Suite to prevent and handle technical faults as well as business faults. Q&A This section lists answers to the questions that were raised during the preview event. Q: Where can retries be configured in Oracle Service Bus? The retry mechanism is used to prevent faults caused by temporary glitches such as short network interruptions. A faulted message is resend (retried) and might succeed this time since the glitch has passed. Retries are an out-of-the-box feature that can be used in Oracle Service Bus and Oracle SOA Suite using the Fault Policy framework. By default, retries are disabled in Oracle Service Bus. Read the full article. SOA & BPM Partner Community For regular information on Oracle SOA Suite become a member in the SOA & BPM Partner Community for registration please visit  www.oracle.com/goto/emea/soa (OPN account required) If you need support with your account please contact the Oracle Partner Business Center. Blog Twitter LinkedIn Mix Forum Technorati Tags: fault handling,vennester,SOA Community,Oracle SOA,Oracle BPM,Community,OPN,Jürgen Kress

  Read the article

• SFTP: How to keep data out of the DMZ

  - by ChronoFish

  We are investigating solutions to the following problem: We have external (Internet) users who need access to sensitive information. We could offer it to them via SFTP which would offer a secure transport method. However, we don't want to maintain the data on server as it would then reside in the DMZ. Is there an SFTP server that has "copy on access" such that if the box in the DMZ were to be compromised, no actual data resided on that box? I am envisioning an SFTP Proxy or SFTP passthrough. Does such a product exist currently?

  Read the article

• Create samba shortcut from command line

  - by neurolysis

  I'm currently wanting to deploy a setup to around 300 Macs. I have most of it scripted, but I'm having trouble creating a working alias to a samba share from the command line. I tried copying it from one Mac to another, but it loses its status as an alias, and instead OSX opens it in TextEdit. From a hexdump, it also looks like it has machine-specific information. So, say I wanted to create an alias to 'smb://server/share' on the desktop from the command line, how would I do that? I have also tried a tell in AppleScript, but it complained about the syntax (specifically, too many slashes, seemingly taking about smb://). Thanks.

  Read the article

• Javascript widgets: do links count as SEO backlinks? [closed]

  - by j0nes

  Possible Duplicate: How good is it for SEO if you have a widget that lives on other sites? On my website I offer an option to let users embed information from my site with some kind of "homepage widget". If a user wants to embed it in his website, he basically has to add one line of Javascript to his HTML files like this: <script src="http://mysite.com/myscript.php?some_options_here"></script> Inside the widget, I export some content from my website and of course create a link back to my website. This is done in Javascript with document.write. document.writeln("My great exported content"); document.writeln('<a href="http://mysite.com?ref=widget>Check mysite.com</a>'); I have Google Analytics set up to track whether the links in there get clicked, and they do. Now I am asking myself if Google recognizes these links as valid backlinks from the embedding domain. I know that Googlebot can parse and execute Javascript, but I have not found any references whether these links also count as "normal" backlinks.

  Read the article

• When copying VM filesystem over netcat, dd copies double the disk size

  - by JivanAmara

  I'm attempting to copy the disk of a working headless virtualbox VM (VM1) on one server to a new VM (VM2) on a vCloud server. I don't have access to the host of VM2. The OS is Windows Server 2003 (32-bit) I start both VMs with a live Knoppix image. I run 'nc -l | dd of=/dev/sda bs=512' on VM2 I run 'dd if=/dev/sda bs=512 | nc ' on VM1 I previously did this with another windows VM and it worked fine. VM1 has a disk of size ~70GB (verified with fdisk); however, the amount of data dd reports read/written is ~139GB. Of course the target machine doesn't work properly. I get a Windows splash screen, then blue error screen with general 'system not working' information. I'm at a loss what could cause this. Any ideas?

  Read the article

• Badwidth-Hogging Linux Server Causing Trouble

  - by BlairHippo

  We have a Linux server (2.6.28-11-generic #42-Ubuntu) that's misbehaving on a client site, gobbling up an entirely unacceptable percentage of the client's bandwidth, and we're trying to figure out what the heck it's doing. And the guy who had the sysadmin skillset has yet to be replaced. We're at a loss for what could be causing all that network traffic, and need to figure it out SOON. What log files should I be looking at to find this information? What analysis tools would you recommend for this task? Please note that I'm not looking for a tool that will allow me to analyze FUTURE traffic. The client is on the verge of shutting the machine off entirely; I need to figure out what it's been doing with the data I already have, if that's at all possible. My thanks in advance for helping a development monkey play sysadmin.

  Read the article

• Cannot add Windows 7 client to SBS 2008

  - by Sandokan

  I have just installed SBS 2008 R2 Standard on VMware Workstation 9 along with Windows 7 Pro N. Both are activated and running fine. I have followed the steps to configure SBS 2008 and am now at the point where I'm to add a computer to the domain. Here is where the problem begins. I have gone through the steps of using the webinterface. On the client I downloaded Launcher.exe. I then run it and get the error "Check computer requirements - Failed" (translated from swedish): "This computer doesn't reach the requirements for connecting to the network." "The computer doesn't reach the maximum requirements for the operating system with regards to connect to the network" The provided link for More information only leads to a general supportpage and doesn't handle this specific error. I have also checked the time settings and they are correct. Any clue as to what this problem could be?

  Read the article

• Can I recover a lost text file in Windows 7?

  - by Marcus Johnson

  How can I recover a lost text file in Windows 7?? It has very important information in it and of course, it is gone because of the stupid Windows Update thing....it just automatically closed all of my stuff and restarted my computer!! Would the text file possibly be in the Temp folder in my computer?? I don't know much about this stuff...but I need it. I didn't save the file which makes me think I can never get it back...but I want to make sure. Thanks. I was using notepad.

  Read the article

• Force Windows to output only mono sound

  - by J. Polfer

  So, the 'right' half of my pair of headphones broke (the transducer+wire are fine, but the earpiece broke on the headband and so the earpiece won't sit over my ear). So now the right channel is being broadcast to my cube neighbors when I wear my headphones. Yes, they look very silly. Is there a way to ensure, in Windows XP (or Windows Media Player), that all stereo sound is downmixed to the left channel only (ie, in mono) so my neighbors don't hear my music? I know that I can setup the mixer to set the balance to 100% left, but information in the right channel won't be heard.

  Read the article

• Free Webinar: A faster, cheaper, better IT Department with Azure

  - by Herve Roggero

  Join me for a free Webinar on Wednesday October 17th at 1:30PM, Eastern Time. I will discuss the benefits of cloud computing with the Azure platform. There isn’t a company out there that would say “No” to reduced IT costs and unlimited scaling bandwidth. This webinar will focus on the specific benefits of the Microsoft Azure cloud platform and will convince you on the sound business rationale behind moving to the cloud. From Infrastructure as a Service (Iaas) to Platform as a Service (Paas), Azure supports quick deployments, virtual machines, native SQL Databases and much more. Topics that will be discussed: - Why use Azure for your Cloud Computing needs - Iaas and Paas Offerings - Differing project approaches to Cloud computing - How Azure’s agility and reduced costs lead to better solutions Attendees of this webinar will also be eligible to receive the following: Free Two Hour Consultation which can include: - Review of Your Cloud Strategy - Cloud Roadmap Review - Review of Data-mart strategies - Review of Mobility Strategies Click Here to Register Now. About Herve Roggero Hervé Roggero, Azure MVP, is the founder of Blue Syntax Consulting, a company specialized in cloud computing products and services. Hervé's experience includes software development, architecture, database administration and senior management with both global corporations and startup companies. Hervé holds multiple certifications, including an MCDBA, MCSE, MCSD. He also holds a Master's degree in Business Administration from Indiana University. Hervé is the co-author of "PRO SQL Azure" from Apress. For more information, visit www.bluesyntax.net.

  Read the article

• Dir and Findstr commands taking a long time to complete in Batch File

  - by user2405934

  dir %DRIVE_NAME%: /S /C /A-D /Q /T:C | findstr ".zip$ .doc$ .xls$ .xpt$ .cpt$ .cpo$ .xlsx$ .pdf$ .dat$ .txt$ .docx$ .csv$" >> file.info I am using above command to list all information in file, as below: 03/27/2013 01:02 PM 86,280 uusr\fr02 h123_frf67_rk_20140327.txt 03/27/2013 01:02 PM 5,513 usr\fr02 h123_frf67_rk_20140328.txt %DRIVE_NAME%: is mapped drive. Folders will be the same; not more than 100 folders and their sub-folders, and there will only be 2 or 3 files at time in any one of the folders. Now the issues is that for one folder it works perfect, but for 80 to 90 folders it is taking too much time. I think it's because of findstr and the different extensions used. Is there any way to make it faster?

  Read the article

• Browser which shows what's been downloaded so far regardless of formatting and layout ?

  - by Mick

  Every now and then a website becomes super-slow (but not broken) because there are too many people looking at it at the same time. When I try and view such a site, say with Firefox, I can see that it is downloading all sorts of components of the site because of the progress information printed at the bottom of the window and I'm sitting there thinking "If only the browser would show me what it's got so far. I don't care if its a jumbled mess, I just want to see what you've got". Does any browser offer such an option?

  Read the article

• china and gmail attachs -

  - by doug

  "We have evidence to suggest that a primary goal of the attackers was accessing the Gmail accounts of Chinese human rights activists. Based on our investigation to date we believe their attack did not achieve that objective. Only two Gmail accounts appear to have been accessed, and that activity was limited to account information (such as the date the account was created) and subject line, rather than the content of emails themselves.” [source] I don't know much about how internet works, but as long the chines gov has access to the chines internet providers servers, why do they need to hack gmail accounts? I assume that i don't understand how submitting/writing a message(from user to gmail servers) works, in order to be sent later to the other email address. Who can tell me how submitting a message to a web form works?

  Read the article

• Rsync : execute permission required

  - by user651488

  I'm using rsync between two servers to transfer files. The problem is some files are not transferred. I get this error : rsync: readlink "/var/www/index.html" failed: Permission denied (13) So I check permissions on the server and after make tests, I notice a file is transferred only if it has these permissions : R-W ! If the file have these permissions : R--, Rsync can't download it !? Command: /usr/bin/rsync -avzr -e "/usr/bin/ssh -i /home/replication/thishost-rsync-key" [email protected]:/var/www/index.html ./ Is it a bug with Rsync ? I find any information about this problem. Thanks for your help Debian Etch 2.6.30 Rsync 2.6.9 protocol version 29

  Read the article

• Downloading file from FTP using cURL

  - by Josiah

  I'm trying to use a cURL command to download a file from an FTP server to a local drive on my computer. I've tried curl "ftp://myftpsite" --user name:password -Q "CWD /users/myfolder/" -O "myfile.raw" But it returns an error that says: curl: Remote file name has no length! curl: try 'curl --help' or 'curl --manual' for more information curl: (6) Could not resolve host: myfile.raw; No data record of requested type I've tried some other methods, but nothing seems to work. Also, I'm not quite sure how to specify which folder I want the file to be downloaded to. How would I do that?

  Read the article

• Jet Brains release WebStorm 5.0

  - by TATWORTH

  At http://www.jetbrains.com/webstorm/whatsnew/index.html?WS50ROW, Jet Brains have announced the release of WebStorm 5.0, an IDE that brings the ease of code writing in VB.NET and C# that you get with ReSharper, to JavaScript, CSS and LESS. (There are some more details in http://blog.jetbrains.com/webide/2012/08/liveedit-plugin-features-in-detail/)Code completion in JavaScript, CSS and LESS is a very welcome feature. I look forward to trying out Web Storm. The download at http://www.jetbrains.com/webstorm/download/index.html comes with a free 30-day trial).Price information is at http://www.jetbrains.com/webstorm/buy/index.jsp - you should note that if you are an open-source developer, you can apply for a free license. The price of a personal license at £23 + VAT is a no-brainer. The price of a Commercial license would have been paid for in a few days of the increased productivity that this tool brings.Web Storm currently requires Google Chrome to run. Like ReSharper it appears to be a very able tool. It includes tools such as:XSLT debuggingJSLint for checking for JavaScript errorsJavaScript debuggingJavaScript unit testing (including code coverage)JavaScript folding regionsCoffeeScript supportWell I suggest that you try WebStorm 5.0

  Read the article

• Should I use a separate 'admin' user as my "root sudo" or grant sudo to my 'app' user?

  - by AJB

  I'm still wrapping my brain around the Ubuntu 'nullify root' user management philosophy (and Linux in general) and I'm wondering if I should 'replace' my root user with a user called 'admin' (which basically has all the powers of the root, when using sudo) and create another user called 'app' that will be the primary user for my app. Here's the context: I'll be running a LNMP stack on Ubuntu 12.04 Server LTS. There will be only one app running on the server. The 'app' user needs to have SUPER privileges for MySQL. PHP will need to be able to exec() shell commands. The 'app' user will need to be able to transfer files via SFTP. And I'm thinking this would be the best approach: nullify 'root' user create a user called 'admin' that will be a full sudoer of root, this will be the new "root" user of NGINX, PHP, and MySQL (and all system software) grant SUPER privileges to 'app' in MySQL Grant SFTP privileges to only the 'app' user. As I'm new to this, and the information I've found in researching it tends to be of a more general nature, I'm wondering if this is a solid approach, or if it's unorthodox in a way that would cause issues down the road. Thanks in advance for any help.

  Read the article

• What are some good tips for a developer trying to design a scalable MySQL database?

  - by CFL_Jeff

  As the question states, I am a developer, not a DBA. I have experience with designing good ER schemas and am fairly knowledgeable about normalization and good schema design. I have also worked with data warehouses that use dimensional modeling with fact tables and dim tables. However, all of the database-driven applications I've developed at previous jobs have been internal applications on the company's intranet, never receiving "real-world traffic". Furthermore, at previous jobs, I have always had a DBA or someone who knew much more than me about these things. At this new job I just started, I've been asked to develop a public-facing application with a MySQL backend and the data stored by this application is expected to grow very rapidly. Oh, and we don't have a DBA. Well, I guess I am the DBA. ;) As far as designing a database to be scalable, I don't even know where to start. Does anyone have any good tips or know of any good educational materials for a developer who has been sort of shoved into a DBA/database designer role and has been tasked with designing a scalable database to support an application like this? Have any other developers been through this sort of thing? What did you do to quickly become good at this role? I've found some good slides on the subject here but it's hard to glean details from slides. Wish I could've attended that guy's talk. I also found a good blog entry called 5 Ways to Boost MySQL Scalability which had some good information, though some of it was over my head. tl;dr I just want to make sure the database doesn't have to be completely redesigned when it scales up, and I'm looking for tips to get it right the first time. The answer I'm looking for is a "list of things every developer should know about making a scalable MySQL database so your application doesn't perform like crap when the data gets huge".

  Read the article

< Previous Page | 566 567 568 569 570 571 572 573 574 575 576 577  | Next Page >