Search Results

Search found 18700 results on 748 pages for 'isolated network'.

Page 571/748 | < Previous Page | 567 568 569 570 571 572 573 574 575 576 577 578  | Next Page >

• DNS Help: Move domain, not mailserver

  - by Preserved

  I'm in the middle of launching a new website for an already-in-use domain. The domain has a complicated email system so we'd like to move that over to the new server a bit later on. Currently the domain DNS is managed by the current webhost. I plan on moving the DNS management back to Network Solutions, then point the A record to the new website's IP. However, currently the DNS has the MX record the same as the A record. When NetworkSolutions is managing the DNS, and I point the A record to the new IP, then the MX record can't be the A record.. Right now: A Record mydomain.com points to IP address 198.198.198.198 MX record mydomain.com points to IP address 198.198.198.198 What I want: A Record mydomain.com points to IP address of new server MX record somehow points to current existing mailserver Does this even make sense?

  Read the article

• iPad revocable vpn access

  - by carpat

  I'm a programmer at my organization, but somehow got drafted into looking into some server stuff so forgive me of my ignorance: They want to give our sales people secure access to our internal sites using their iPads. This must be secure (obviously) but also revocable from the company's side (if someone quits they can no longer access our network). I see from http://support.apple.com/kb/HT1288 that the iPad supports "RSA SecurID", "CRYPTOCard", and "Kerberos" authentication methods. Will one of these do what we need? Are there any major differences between them?

  Read the article

• Router used as ethernet bridge wont show up

  - by user1255271

  I have a Netgear router in my living room that has the wireless signal. It is connected to a Powerline plug that goes up to my bedroom. That is plugged into another router that is used as an ethernet hub. It's cables go into my PS3 and my server. The second router shows up as a hidden network on my laptop, and I can connect to it. But it is not listed as an attached device on my main router, and my laptop says that it connects straight to the main router, not the second one. How can I connect to this router? Aside from swapping the two? Thanks in advance.

  Read the article

• Ubuntu, connecting to WLAN

  - by Holly

  Hello, I successfully installed Ubuntu onto my usb hard drive. However, I'm not sure what the issue is with my internet. I'm not familiar enough with ubuntu to know whether this is a problem with recognizing my wireless card or with my internet, etc. So I suppose my question is, how do I tell whether it's recognizing my wireless card? (Network manager isn't showing any wireless signals, though I wasn't sure if it was supposed to. ) And, if it's not working, how do I go about troubleshooting that issue? Thanks!

  Read the article

• Issue about mapping MAC address to Ipv6 address

  - by deepsky

  I know that the address in ipv6 with prefix range 001 to 111 should use a 64-bit interface identifier that follows the EUI-64 format, which translates the MAC to ipv6 as below. MAC:00-02-b3-1e-83-29 --> 02-02-b3-ff-fe-1e-83-29 --->ipv6 addr: fe80::202:b3ff:fe1e:8329 Then I checked my network status with ipconfig /all on my windows XP, but it seems my ipv6 address doesn't follow the above rule: MAC:00-24-81-XX-XX-XX ipv6 addr:2001:da8:8006:225:0:24:81XX:XXXX Obviously it doesn't follow the EUI-64 format. Instead it just directly use the MAC as the last 8 bytes. Anyone know the reason? Pls Correct me if I am wrong.

  Read the article

• Log highlighted lines to window in irssi

  - by Sebastian P.

  I usually keep an irssi session running on my server at all times. Often times it also takes me quite a while between remembering that I in fact have it running. Therefore I'd like to know if there's an easy way to log all lines that are highlighted to a custom window, such that I later, when I return, can see what people have said that was directed at me. Most useful would of course be if it logged both nickname, time and place (channel, network) of the message. I've been looking around, and haven't managed to get anything working which accomplishes this, so it would be splendid if such a thing existed.

  Read the article

• Debian crashed, file system is read-only and cannot backup - How Do I find/mount a USB drive?

  - by Spiros

  We have a Debian server (vm's) here at work and the server crashed after a power failure. I can only boot the system in maintenance mode, and the whole file system is set to read only. I can run fsck though maintenance mode, however I would like to get a backup of some files before I do. Problem: I cannot access the net since there is no network connectivity in maintenance mode, and for some reason I try to add a USB flash drive to the computer but I can't find it through the console. Question: how to you find/mount a usb drive on Debian? I have tried several resources from the internet but nothing worked. Is there any other way I could get a backup of my files? I cannot start networking since the filesystem is set to read only. Any help would be appreciated.

  Read the article

• Most secure way to have IPtables auto-loaded using Debian / Linux

  - by networkIT

  I'd like to know the safest way to load iptables using Debian. Of course, I can use a script that uses iptables-restore : #!/bin/sh iptables-restore < /etc/firewall.conf but : 1) where is the safest place to have it loaded ? /etc/network/if-up.d ? I'm concerned about the script being loaded early enough at boot time, and reliably enough when plugging/unplugging interfaces ... 2) is this script method using iptables-restore the most secure way ? 3) additionnally, how much does the answer validity stretch to other Linux distros ( Ubuntu, Fedora, CentOS ) ? Thanks ^^

  Read the article

• Lots of artifacts while streaming HD content with VLC 0.9.9 on CentOS

  - by Zsub

  I'm trying to stream (multicast) a x264 encoded file using VLC. This in itself succeeds, but the stream has a huge lot of artifacts. This seems to suggest that the data cannot be transported fast enough. If I check network usage, though, it's only using about 15 mbit. I have a similar SD stream which functions perfectly. I think I could improve stream performance by not streaming the raw data, but I cannot seem to get this working. It seems that on keyframes all artifacts are removed for a short while (less than a second). This is the command I use: vlc -vv hdtest.mkv --sout '#duplicate{dst=rtp{dst=ff02::1%eth1,mux=ts,port=5678,sap,group="Testgroup",name="TeststreamHD"}}' --loop Which is all one long line.

  Read the article

• NSD reply from unexpected source

  - by Ximik

  I have server with NSD. There are MAIN_IP and ADD_IP. When I try to get IP of my site from server I have right output dig @localhost my_site.com But when I try to make this from my PC, I have dig @my_ns_server.com my_site.com ;; reply from unexpected source: MAIN_IP#53, expected ADD_IP#53 (ADD_IP is IP of my_ns_server.com) What should I do? UPD: My interfaces conf auto eth2 allow-hotplug eth2 iface eth2 inet static address xxx.xxx.xxx.234 netmask 255.255.255.252 network xxx.xxx.xxx.232 broadcast xxx.xxx.xxx.235 gateway xxx.xxx.xxx.233 dns-nameservers MY_ISP_IP dns-search MY_ISP_DOMAIN auto eth2:0 iface eth2:0 inet static address xxx.xxx.xxx.124 netmask 255.255.255.0 xxx.xxx.xxx is the same for all IPs

  Read the article

• CentOS: OpsCenter does not see other node's agent

  - by Alice

  I'm new with Apache Cassandra. I am trying to install a little sample cluster using two CentOS server. I followed the documentation (Tarball installation) and the nodes are up. However, when I go to OpsCenter, the nodes cannot see each other's agent (there is always "1 of 2 agents connected"..I tried to fix, but nothing change). I tried both to disable and enable SSL, I tried to set the incoming_interface in opscenter.conf, I tried almost everything the network suggested to me, but the problem persisted. Now, I have SSL enabled, and agent log tell me: "There was an error when attempting to load stored rollups." Is there someone that could help me, please?

  Read the article

• Can't connect to Internet through WiFi, but can with cable

  - by aldy505

  I'm using Windows 7 32-bit, Toshiba Portege laptop. I want to connect to the WiFi, usually I can do that easily. But, I don't know.. maybe when I tried to install a Microsoft Research: Mesh Virtual WiFi that could connect more than 2 wireless networks. I wanna try in connecting both Wireless router and my personal Ad-Hoc. Now, my laptop don't recognize my WiFi, well, I can connect to the WiFi but it says: "Limited access" and doesn't really connect to the internet. But when I plug the LAN cable, it works. I know the problem is in the laptop's wireless connection or in the properties. Any help for this? UPDATE: The IP and DNS settings, I set to automatic, and when I ran diagnostic, Windows tells me that the wireless network adapter is the problem, but they told me to insert the LAN cable, so how to fix the wireless? They didn't tell me how to fix that.

  Read the article

• Copy Ubuntu distro with all settings from one computer to a different one

  - by theFisher86

  I'd like to copy my exact setup from my computer at work to my computer at home. I'm trying to figure out how to go about doing that. So far I've figured this much out. On the source computer run dpkg --get-selections > installed-software and backup the installed-software file Backup /etc/apt/sources.list Backup /usr/share/applications/ to save all my custom Quicklists Backup /etc/fstab to save all my network mounts Backup /usr/share/themes/ to save the customization I've done to my themes I'm also going to backup my entire HOME directory. Once I get to the destination computer I'm going to first do just a fresh install of 11.10 Then I'll copy over my HOME directory, /etc/apt/sources.list, /usr/share/appications, /etc/fstab and /usr/share/themes/ Then I'm going to run dpkg --set-selections < installed-software Followed by dselect That should install all of my apps for me. I'm wondering if there's a way/need to backup dconf and gconf settings from the source computer? I guess that's my ultimate question. I'd also like any notes on anything else that might need backed up as well before I undertake this project. I hope this post is legit, I figured other people would be interested in knowing this process and I don't see any other questions that seem to really document this on here. I'd also like to further this project and have each computer routinely backup all the necessary files so that both computer are basically identical at all times. That's stage 2 though...

  Read the article

• Win Server 2003 - Task Scheduler - Tasks with GUI and Services

  - by august_month

  I need to run excel macro daily. I scheduled it with Windows Scheduler and it worked fine until I had to change my password. I wonder if it's possible to have a task scheduled without a password? As alternative we have third party scheduling software, but this software cannot launch excel. The tech support said that since excel has gui and scheduling software runs as service with "Allow to interact to Desktop" disabled, it cannot launch excel. Also tech support mentioned that "Allow to interact to Desktop" is not supported as of Vista. I totally trust tech support guy, I just need a work around that would make my network administrator and me happy. Regards.

  Read the article

• AR242x / AR542x wireless card not working

  - by Pipan87

  My wifi worked perfect until I updated to the latest version of Ubuntu. Now I don't find any wireless connections at all. I have tried lots of guides on the internet but I can't get it to work. I did however start to work once after writing something I don't remember in Terminal, but after rebooting it stopped working again. Some info (don't know if you need more to help): 01:00.0 Ethernet controller: Atheros Communications AR8121/AR8113/AR8114 Gigabit or Fast Ethernet (rev b0) Subsystem: Acer Incorporated [ALI] Device 022c Flags: bus master, fast devsel, latency 0, IRQ 44 Memory at 55200000 (64-bit, non-prefetchable) [size=256K] I/O ports at 3000 [size=128] Capabilities: [40] Power Management version 2 Capabilities: [48] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [58] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [180] Device Serial Number ff-93-2e-de-00-23-8b-ff Kernel driver in use: ATL1E Kernel modules: atl1e 02:00.0 Ethernet controller: Atheros Communications Inc. AR242x / AR542x Wireless Network Adapter (PCI-Express) (rev 01) Subsystem: Foxconn International, Inc. Device e00d Flags: bus master, fast devsel, latency 0, IRQ 18 Memory at 54100000 (64-bit, non-prefetchable) [size=64K] Capabilities: [40] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [60] Express Legacy Endpoint, MSI 00 Capabilities: [90] MSI-X: Enable- Count=1 Masked- Capabilities: [100] Advanced Error Reporting Capabilities: [140] Virtual Channel Kernel driver in use: ath5k Kernel modules: ath5k

  Read the article

• Which is the best internet security + Antivirus solution for Windows?

  - by metal gear solid

  Which is the best internet security + Antivirus solution for Windows? free/opensource or commercial it doesn't matter I need best solution. Is Kaspersky best ? or any other? http://www.kaspersky.com/kaspersky_internet_security Award-winning technologies in Kaspersky Internet Security 2010 protect you from cybercrime and a wide range of IT threats: * Viruses, Trojans, worms and other malware, spyware and adware * Rootkits, bootkits and other complex threats * Identity theft by keyloggers, screen capture malware or phishing scams * Botnets and various illegal methods of taking control of your PC or Netbook * Zero-day attacks, new fast emerging and unknown threats * Drive-by download infections, network attacks and intrusions * Unwanted, offensive web content and spam

  Read the article

• WLC 4400. Get IP

  - by Edward Connelly

  I have three SSID. one is a guest network and I'm having problems with lease times. Its set for web authentication so it passes IPs out even if someone doesn't try and authenticate. Is there a way to get that IP back and not hand another to that mac for a period of time? Poor planning and we didn't allocate enough address space, and we are sandwitched. We could go with another address, but we would have to reconfig lots. since its guest its vlan'd with no access to anthing but the firewalls. would have to change ACLs and routes and interfaces. if it isn't possible we will just have to go that route, just thought there might be an easier solution. session timeout is enabled with 1 hr lease time is set to 4 hrs. no helper DHCP and internal DHCP is set with the space split across three WLCs (60 waps split across those as well).

  Read the article

• 'DNS service isn't responding' in windows 7

  - by pradeeptp

  Hi All, I bought a brand new Dell Studio 1558 just last week. It has windows 7 home premium 64-bit installed on it. My friend who is occupying the adjacent room has a laptop with windows XP. Both of us are connecting to the same wireless router of the hotel. My friend is able to connect to the wireless network without any trouble, but when I try to connect, I get the error "DNS service isn't responding". I met two more people in the same hotel with win XP laptop and they too dont have any problem. I have gone to possibly all the forums and website but I haven't been able to fix this error :(. I have done all the basic troubleshooting but I have no luck yet. Pls help. Following is one forum where the problem seem to have been trouble shooted but not for all. http://social.technet.microsoft.com/Forums/en/w7itpronetworking/thread/eeb84518-903d-46d1-9398-80cf211878d7

  Read the article

• Computer Invisible On Domain

  - by Giawa

  Good afternoon, I'm sorry that this isn't a programming question specifically, but stackoverflow has been great at answering questions in the past, so I thought I'd give it a shot. One of our Linux users attempted to install Cygwin on our Windows Server 2008 Domain Controller. Now it is no longer possible to browse the domain and see all of the computers. For example, \\my_domain_name will just bring up a username/password dialog box (that will not accept any username or password, even the domain administrator) and no computers will ever be listed. However, I can still connect to computers based on their name or IP address. So \\eridanus or \\192.168.1.85 still work to connect to the shared directories of computers on our network. Does anyone know where I can find these settings? and how I can fix this problem? Thanks, Giawa

  Read the article

• How do I connect a laptop running Windows 7 to an Android phone using WiFi Direct?

  - by user130768

  From where I am sitting, Windows 7 does not appear to support WiFi Direct connections to Android mobile devices. Specifically, turning on WiFi Direct on my Samsung Galaxy S II does not make the device visible as a potential WiFi network connection. Windows 8 is said to support WiFi Direct, but I have no desire to upgrade at this time. I have successfully set up ad hoc WiFi connections between the S II and my laptop before, but as you may be aware, these are not the same as WiFi Direct. Before posting this question, I searched [ "Windows 7" "WiFi Direct" ] and variations thereof, and dutifully slogged through dozens of lame or irrelevant responses on various forums, badly made YouTube videos, and probable Trojan horse distribution sites. If someone out there knows how to do this, it's buried in the noise.

  Read the article

• NAT : understanding about interconnection

  - by PITCHY

  English version below J'ai 2 routeurs A et B relié en série avec les ip respectives ( 10.0.0.1/30 10.0.0.2/30) sur le routeur A j'ai activé la fonction NAT avec un pool (200.0.0.1 - 200.0.0.15/28). Lorsque je sors je prends donc un ip du pool par exemple 200.0.0.10. Comment ça fonctionne sachant que ma nouvelle ip (200.0.0.10) ne se trouve pas sur le meme réseau que mon interface de destination (10.0.0.2)? English: I have 2 routers A and B, interconnected with a serial connection, with the ip's 10.0.0.1/30 for A and 10.0.0.2/30 for B. On router A NAT was activated with the pool 200.0.0.1 - 200.0.0.15/28. When connection to this router, I get an ip from the pool, for example 200.0.0.10. Knowing my new ip is 200.0.0.10, which is not on the same network as my destination interface (10.0.0.2), how can this work?

  Read the article

• Is it possible to get a google voice number without already having a phone number?

  - by boost

  I'm sorry if this is the wrong place to post this, but I couldn't find a more suitable website in the stackexchange network. I currently have no phone number; I can make outgoing calls via the widget in gmail, but I cannot receive calls (as far as I know). I know that you can set up a google voice number to forward to google chat, and this is exactly what I want. The problem is, I can't get a google voice number in the first place, because it first requires that I have an existing phone number, even if I wouldn't use it. So, it is possible to skip providing an existing phone number, and just get a google voice number that forwards to google chat? Alternatively, is there any free phone service that can be used without a phone and lets you receive calls from any number? I realize I'm kind of asking for free candy, but, if it's out there, I'd be a fool

  Read the article

• Is it possible to host a web server from behind a NAT

  - by iamrohitbanga

  My PC is behind a NAT router that has a public IP address. If I want to host a website then I believe I need a domain name which I can purchase from some site which would pledge to resolve all DNS requests for that domain name and send the IP address of my NAT router (assuming I do not want to host my domain name on their servers). Now I want to host a web server on my computer. What changes should be done to the NAT router's configuration to forward all HTTP requests for example.com to my PC in the internal network. Is the above strategy correct? Is it commonly used?

  Read the article

• How to make ip Address static (eth0)

  - by Jordan Angelucci

  I'm having a really hard time configuring ubuntu 13.04 to have a static ip address. I have tried multiple solutions but everytime I reboot (can't do the network reset command because ubuntu freezes) I end up with no connection. Here is what I get when i type ifconfig into the terminal: eth0 Link encap:Ethernet HWaddr 10:bf:48:bc:07:cb inet addr:192.168.0.8 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::12bf:48ff:febc:7cb/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1763067 errors:0 dropped:0 overruns:0 frame:0 TX packets:1024326 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2284491220 (2.2 GB) TX bytes:136809317 (136.8 MB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:1840 errors:0 dropped:0 overruns:0 frame:0 TX packets:1840 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:185688 (185.6 KB) TX bytes:185688 (185.6 KB) I have also tried this: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.0.160 netmask 255.255.255.0 broadcast 192.168.0.255 gateway 192.168.0.1 dns-nameservers 24.222.0.94 dns-nameservers 24.222.0.95 If anyone could help me it would be very much appreciated.

  Read the article

• Broadcasted networks appear cached with netsh? [on hold]

  - by Joe

  We have a company mandate to hide certain windows functions. I'm working on a company application which will allow my users to configure WiFi networks. The app is scanning broadcasted networks using: "netsh wlan show networks" it will return networks that have been turned off. For example: I will run the command and then unplug my wireless router with the SSID "Netgear". For several minutes after turning off the network, the show networks command will continue to return "Netgear". Does anyone know where this gets cached, how to clear it out, or how to force a fresh scan of "netsh wlan show networks"? Thanks all, J

  Read the article

< Previous Page | 567 568 569 570 571 572 573 574 575 576 577 578  | Next Page >