Search Results

Search found 27016 results on 1081 pages for 'entry point'.

Page 572/1081 | < Previous Page | 568 569 570 571 572 573 574 575 576 577 578 579  | Next Page >

• apxs cannot install mod_cloudflare on centos

  - by Adam

  [ Linux - CentOS - Apache 2.2 - mod_cloudflare - apxs2 ] I have changed my nameservers to point to CloudFlare. The problem is that all the IP addresses are coming in as CloudFlare's. This is no good, because I have to monitor and block some specific traffic. mod_cloudflare is supposed to resolve this but I have been unable to get this installed. The command in the documentation uses apxs2. I can't figure out how to install this, or if it just means for 'apache 2.4'. I'm running 2.2.3, and I can use 'apxs'. When I run: apxs -aic mod_cloudflare.c I get the error apxs:Error: Command failed with rc=65536 Does this mean I need apxs2 or something else? How do I get mod_cloudflare working on my server? I appreciate any help, the documentation is vague and limited.

  Read the article

• Usage of two Routers on LAN

  - by brusilva

  I've currently own a Linksys E4200 and a Thomson 546v6. Because I have an IPTV service I must set the Thomson as the main router connected to the phone line so that I can distribute the video signal for 2 specific ports and the other two for LAN Access. The problem is that the Thomson doesn't like port forwards, it usually doesnt work and since I have a good router (linksys) currently only working as Access Point I would like to use it as a router itself. I don't want to do a NAT beyond NAT so my question is should I connect the E4200 and to thomson and set the E4200 as a DMZ machine and then control all trafic on the E4200 itself or is there any other option that could suit my needs better?

  Read the article

• Country specific content vs global content

  - by Ando

  I have a global product presentation website myproduct.com For certain countries I also own the country domain: myproduct.co.uk, myproduct.com.au, myproduct.es, myproduct.de, etc. The presentation website is translated in multiple languages and I set up redirects: myproduct.es will redirect to myproduct.com/es/, myproduct.de will redirect to myproduct.com/de/, etc. . The content so far is the same, just translated in different languages. The advantages are that it's easy to keep the content aligned - everything is managed from one centralized dashboard (I'm using Wordpress with qtranslate). Now I'm running into trouble as for different countries I want localized content - for UK I want to run different promotions and use a different reseller than for .com.au so I would like that users coming from myproduct.co.uk see something different than those coming from myproduct.com.au (and not be redirected to myproduct.com as they are right now). How can I achieve this? I could duplicate the whole main website and modify only certain parts but then I would have a lot of duplicate content (e.g. info about how the product works) and I would have pages that are likely to change (FAQ page) that I would have to keep updated over all websites. I can duplicate only partially the main website: on the localized website I would have only the pages that are different and then all other links would point to the .com site. This would solve the duplication problem but would cause confusion for the user as you would navigate from .co.uk to .com without noticing and then wonder how to get back. Other, better option?

  Read the article

• Handling FreeBSD package upgrades using pkg_add

  - by larsks

  I'm trying to use FreeBSD's pkg_add command to install and upgrade binary packages in a build-once-install-on-multiple-machines sort of scenario. It works well when installing a new package, but upgrades are baffling me. For example, if I want to upgrade a package that is depended on by another package, I can't just install it: # pkg_add /path/to/somepackage-2.0.tbz pkg_add: package 'somepackage' or its older version already installed At this point, I can delete the older version of the package if I pass -f to the pkg_delete command: # pkg_delete -f somepackage-1.0 pkg_delete: package 'somepackage-1.0' is required by these other packages and may not be deinstalled (but I'll delete it anyway): anotherpackage-1.0 But...and this is the killer...now the dependency information is gone! I can install the upgrade: # pkg_add /path/to/somepackage-2.0.tbz And now attempts to delete it will succeed without any errors: # pkg_delete somepackage-2.0 How do I handle this gracefully (whereby "gracefully" means "in a fashion that preserves dependency information without requiring me to rebuild/reinstall and entire dependency chain"). Thanks!

  Read the article

• Procedural content (settlement) generation

  - by instancedName

  I have, lets say, something like a homework or assignment to do. Roughly said I need to write an algorithm (pseudo code is not necessary, just in depth description) of procedure that would generate settlements, environment and a people to populate it with, as part of some larger world generation procedure. The genre of game is not specified, it could be any genre (rpg, strategy, colony simulation etc.) where interacting with large and extensive world is central to the game. Procedure should be called once per settlement. At the time of calling, world generation procedure makes geography, culture and history input available. Output should be map of the village and it's immediate area, and various potential additional information like myths, history, demographic facts etc. Bonus would be quest ant similar stuff, but that not really my focus at the moment. I will leave quality of the output for later when I actually dig little deeper into this topic. I am free to change parameters as long as I have strong explanation for doing so. Setting of the game is undetermined so I am free to use anything that I like the most. Ok, so my actual question is: Can anyone who has some experience in this field of game design recommend me some good literature, or point me in the direction where I should look/reed/study? I'm somewhat experienced game programmer, but I've never been into game design till now so any help will be great. I want to do this assignment as good as I can. As for deadline, it's not strictly set, but lets say I don't want it to take longer then few weeks, one month at worst case.

  Read the article

• Augmenting functionality of subclasses without code duplication in C++

  - by Rob W

  I have to add common functionality to some classes that share the same superclass, preferably without bloating the superclass. The simplified inheritance chain looks like this: Element -> HTMLElement -> HTMLAnchorElement Element -> SVGElement -> SVGAlement The default doSomething() method on Element is no-op by default, but there are some subclasses that need an actual implementation that requires some extra overridden methods and instance members. I cannot put a full implementation of doSomething() in Element because 1) it is only relevant for some of the subclasses, 2) its implementation has a performance impact and 3) it depends on a method that could be overridden by a class in the inheritance chain between the superclass and a subclass, e.g. SVGElement in my example. Especially because of the third point, I wanted to solve the problem using a template class, as follows (it is a kind of decorator for classes): struct Element { virtual void doSomething() {} }; // T should be an instance of Element template<class T> struct AugmentedElement : public T { // doSomething is expensive and uses T virtual void doSomething() override {} // Used by doSomething virtual bool shouldDoSomething() = 0; }; class SVGElement : public Element { /* ... */ }; class SVGAElement : public AugmentedElement<SVGElement> { // some non-trivial check bool shouldDoSomething() { /* ... */ return true; } }; // Similarly for HTMLAElement and others I looked around (in the existing (huge) codebase and on the internet), but didn't find any similar code snippets, let alone an evaluation of the effectiveness and pitfalls of this approach. Is my design the right way to go, or is there a better way to add common functionality to some subclasses of a given superclass?

  Read the article

• Public IP shows strange characters and Facebook registers logged-in session to a different location

  - by Stuart Kershaw

  I'm encountering some IP strangeness today and hoping to find an explanation. In short, I'm based in Seattle, WA with my ISP being Comcast. While browsing Facebook's account settings, I noticed that my active session was located to Mount Laurel, NJ. At that point I ran a search in Google for 'my public IP', which returned an interesting result: a string of characters in the following format: 2601:8:b000:xxx:xxxx:xxxx:xxxx:xxxx Normally, a search for my IP returns something like: 67.xxx.xx.xxx A phone call to Comcast got me nowhere, but using Comcast's phone-menu debugging tools, I was able to send a 'refresh signal' to my modem. After that, the search for 'my public IP' yielded the expected result... for about 5 minutes, and then it returned to the new string of characters. Does anyone know of an explanation for this?

  Read the article

• Remote Working & Relocation

  - by James Burgess

  Sorry if this question is a duplicate, I did some extensive searching and found nothing on quite the same topic (though a couple on partially-overlapping topics). Recently, whilst on holiday in Munich, Germany, I was taken aback by the sheer number of programming-related posts available in the city that I easily qualify for (both in terms of knowledge, and experience). The advertised working environments seemed good and the pay seemed to be at least as good as what I'd expect here in the UK. Probably 80% of the advertisements I saw on the underground were for IT-related jobs, and a good 60% of those I was easily qualified for. At the moment, I work as a freelancer mostly on web and small software projects, but seeing the vast availability of jobs in Munich versus my local area has me thinking about remote working. I'm unable to relocate for a job for the next 3 years (my wife has a contract to continue being a doctor at her current hospital for that time) but would almost certainly be open to it after that (after all, my wife and I both love Munich). In the meanwhile, I would be very interested in remote-working. So, my question is thus do companies ever take on remote workers (even with semi-frequent trips to the office) from abroad, with a view to later relocation? And, if so, how do you go about broaching the topic with a recruiter when getting in contact about a job posting? Language isn't a barrier for me, here, as 90% of the jobs I've looked up in Munich don't require German speakers (seems they have a big recruiting market abroad). I'm also under no illusions about the disadvantages of remote working, but I'm more interested in the viability of the scenario rather than the intricacies (at least at this point). I'd really appreciate any contributions, especially from those who have experience with working in such a scenario!

  Read the article

• The canonical "blocking BitTorrent" question

  - by Aphex5

  How can one block, or severely slow down, BitTorrent and similar peer-to-peer (P2P) services on one's small home/office network? In searching Server Fault I wasn't able to find a question that served as a rallying point for the best technical ideas on this. The existing questions are all about specific situations, and the dominant answers are social/legal in nature. Those are valid approaches, but a purely technical discussion would be useful to a lot of people, I suspect. Let's assume that you don't have access to the machines on the network. With encryption use increasing in P2P traffic, it seems like stateful packet inspection is becoming a less workable solution. One idea that seems to make sense to me is simply throttling down heavy users by IP, regardless of what they're sending or receiving -- but it doesn't seem many routers support that functionality at the moment. What's your preferred method to throttle P2P/BitTorrent traffic? My apologies if this is a dupe.

  Read the article

• Handling UTF-8 with BOM in HTTP

  - by Alois Mahdal

  Say I have a script which at some point serves a plain text file as a content (right after "\n\n"). These files are provided by users, but I can expect they will be UTF-8. So I hard-wire Content-Type: text/plain; charset=UTF-8. But while I can teach users to save everything in UTF-8, I can't be very sure that the files will be without BOM ("\xEE\xBB\xBF"), as at least on Windows, this is not very clearly distinguished in common plain text editors and not every one of them uses the same default. So what about these files created on Windows, where they may/may not start with BOM? Should/will server or UA get rid of this debris for me? Or is it my task to prepare clean UTF-8, i.e. open each file and check whether BOM needs to be removed?

  Read the article

• Postfix configuration: different outgoing hosts based on sender

  - by Joe

  I've seen a few answers to this on the web, but nothing definitive nor any good examples. I relay all my mail out through Postfix, currently everything sent to my ISP's mail server. However, there are a few users with gmail accounts or gmail-hosted accounts; I'd like to route their outgoing mail through Google's servers (since it will then appear in their Gmail sent folder). All email NOT from one of these senders should go out through the default relayhost. I believe I need to use the "sender_dependent_default_transport_maps" configuration within Postfix, but can't find a good example on what this setup looks like. Can anyone point me at a specific setup?

  Read the article

• Simple Architecture Verification

  - by Jean Carlos Suárez Marranzini

  I just made an architecture for an application with the function of scoring, saving and loading tennis games. The architecture has 2 kinds of elements: components & layers. Components: Standalone elements that can be consumed by other components or by layers. They might also consume functionality from the model/bottom layer. Layers: Software components whose functionality rests on previous layers (except for the model layer). -Layers: -Models: Data and it's behavior. -Controllers: A layer that allows interaction between the views and the models. -Views: The presentation layer for interacting with the user. -Components: -Persistence: Makes sure the game data can be stored away for later retrieval. -Time Machine: Records changes in the game through time so it's possible to navigate the game back and forth. -Settings: Contains the settings that determine how some of the game logic will apply. -Game Engine: Contains all the game logic, which it applies to the game data to determine the path the game should take. This is an image of the architecture (I don't have enough rep to post images): http://i49.tinypic.com/35lt5a9.png The requierements which this architecture should satisfy are the following: Save & load games. Move through game history and see how the scoreboard changes as the game evolves. Tie-breaks must be properly managed. Games must be classified by hit-type. Every point can be modified. Match name and player names must be stored. Game logic must be configurable by the user. I would really appreciate any kind of advice or comments on this architecture. To see if it is well built and makes sense as a whole. I took the idea from this link. http://en.wikipedia.org/wiki/Model%E2%80%93view%E2%80%93controller

  Read the article

• MySQL mistake with grant option

  - by John Tate

  I am unsure reading the MySQL documentation if creating a user with the GRANT option will give them the power to create users and grant privileges, or change the privileges of other users databases. I have been creating databases for users like this CREATE DATABASE user; USE user; GRANT ALL PRIVILEGES ON *.* TO 'user'@'localhost' IDENTIFIED BY 'password' WITH GRANT OPTION; Is this the best way of doing it or have I just given my users too much control? They are people I am hosting sites for. Thankfully at this point they are trustworthy. I use quotas. Edit: I have realized I have been granting users access to all databases. This is obviously stupid I should be using this: GRANT ALL PRIVILEGES ON database.* to 'user'@localhost' IDENTIFIED BY 'password' What is the simplest way to revoke privileges for every user except root so I can quickly end this catastrophic rookie mistake?

  Read the article

• Proportional speed movement between mouse and cube

  - by user1350772

  Hi i´m trying to move a cube with the freeglut mouse "glutMotionFunc(processMouseActiveMotion)" callback, my problem is that the movement is not proportional between the mouse speed movement and the cube movement. MouseButton function: #define MOVE_STEP 0.04 float g_x=0.0f; glutMouseFunc(MouseButton); glutMotionFunc(processMouseActiveMotion); void MouseButton(int button, int state, int x, int y){ if(button == GLUT_LEFT_BUTTON && state== GLUT_DOWN){ initial_x=x; } } When the left button gets clicked the x cordinate is stored in initial_x variable. void processMouseActiveMotion(int x,int y){ if(x>initial_x){ g_x-= MOVE_STEP; }else{ g_x+= MOVE_STEP; } initial_x=x; } When I move the mouse I look in which way it moves comparing the mouse new x coordinate with the initial_x variable, if xinitial_x the cube moves to the right, if not it moves to the left. Any idea how can i move the cube according to the mouse movement speed? Thanks EDIT 1 The idea is that when you click on any point of the screen and you drag to the left/right the cube moves proportionally of the mouse mouvement speed.

  Read the article

• How do I get my graphic card to work properly?

  - by Lucas

  I been having some problems with my graphic card for a time now. But I had enough when I did'nt get Oil Rush to work on my HP Pavilion g6. The system has suggested hardware drivers for me, but the first time I installed them they pretty much fucked up the graphics. After some time I managed to get the computere to work properly (I thought) again. When the game did'nt work I tried to the hardware drivers for the graphic card anyway. First of all there was to possible choices insted of one, as the last time I installed the drivers (when it did'nt work out so good). The choices are: ATI/AMDs proprietary video drivers FGLRX (update for edition) and Proprietary FGLRX-video drivers for ATI/AMD I realized the drivers probebly are pretty much the same, so I tried the first one. But this did'nt work. Instead I was asked to "Look in to /usr/var/log/jockey.log". This did'nt helped me much. Instead I choiced the other one, wich was installed and after reboot there where some changes. First of all there was a lot more details for Unity that was'nt there before and some shortkeys are now working that did'nt before (like Ctrl + T and the Prt Sc-button). But overall everything doesn't work as it used to. Like when you browse between the workspaces it doesn't look the same. To get to the point: it doesn't work well right now even if I got some things better and now will not Oil Rush (as I mentioned in the beginning) even start. SO! Can someone give me any advice with this? I'm stuck. Can't manage to see whats wrong right now. Any help? My graphic card is AMD Radeon HD 6470M.

  Read the article

• Route an IP from WAN to a host on LAN on OpenWRT

  - by Zsub

  EDIT: I know how to use NAT, I specifically want the server to be reachable on two IP's, one private, one public, with the firewall of the OpenWRT in between, if feasible. At the office we have recieved a /29 from our ISP. The first address is reserved for their endpoint, so I'm free to use five addresses. We run a local network, so of course there is a router in between running OpenWRT to provide all hosts with (W)LAN (dhcp from a private range). However, we also have a server running OS X Server 10.6 (Snow Leopard) and I'd like that server to be accessible both from the LAN using a private IP as well as from the WAN on it's own public IP. Point of note is that the server only has one network port, so multiple NICs is not an option, unfortunately. How would I go about doing this?

  Read the article

• Losing partitions after every reboot

  - by Winston Smith

  I have an Acer laptop with one hard disk, which up until yesterday had 4 partitions: Recovery Partition (13GB) C: (140GB) D: (130GB) OEM Partition (10GB) I read that the OEM partition has all the stuff needed to restore the laptop to the factory settings, but since I'd already created restore disks and I needed the space, I wanted to get rid of it. Yesterday, I used diskpart to do that. In diskpart, I selected the OEM partition and issued the delete partition override command which removed it. Then I extended the D: partition into the unused space using windows disk management. Everything worked fine, until I rebooted my laptop, at which point the D: drive vanished. Looking in windows disk management again, I can see that there's an OEM partition of 140GB, which is obviously my D: drive. So I used EASEUS Partition Master and assigned a drive letter to the 'OEM' partition and I was able to access my files again. However, every time I reboot, it reverts back. How do I fix this permanently?

  Read the article

• Where Twitter Stands Heading Into 2013

  - by Mike Stiles

  As Twitter continued throughout 2012 to be a stage on which global politics and culture played itself out, the company itself underwent some adjustments that give us a good indication of what users and brands can expect from the platform in 2013. The power of the network did anything but fade. Celebrities continued to use it to connect one-on-one. Even the Pope signed on this year. It continued to fuel revolutions. It played an exponentially large factor in this US Presidential election. And around the world, the freedom to speak was challenged as users were fired, sued, sometimes even jailed for their tweets. Expect more of the same in 2013, as Twitter has entrenched itself, for individuals, causes and brands, as the fastest, easiest, most efficient way to message the masses so some measure of impact can come from it. It’s changed everything, and it’s not finished. These fun facts reveal the position of strength with which Twitter enters 2013: It now generates a billion tweets every 2.5 days It has 500 million+ users The average Twitter user has tweeted 307 times 32% of everyone using the Internet uses Twitter It’s expected to bring in $540 million in ad revenue by 2014 11 new accounts are created every second High-level Executive Summary: people love it, people use it, and they’re going to keep loving and using it. Whether or not outside developers love it is a different matter. 2012 marked a shift from welcoming the third party support that played at least some role in Twitter being so warmly embraced, to discouraging anything that replicates what Twitter can do itself…or plans to do itself. It’s not the open playground it once was. Now Twitter must spend 2013 proving it can innovate in-house and keep us just as entranced. Likewise, Twitter is distancing itself from Facebook. Images from the #1 platform’s Instagram don’t work on Twitter anymore, and Twitter’s rolling out their own photo filter product. Where the two have lived in a “plenty of room for everybody” symbiosis up to now, 2013 could see the giants ramping up a full-on rivalry. Twitter is exhibiting a deliberate strategy. Updates have centered on more visually appealing search results, and making finding and sharing content easier. Deals have been cut with some media entities so their content stands out. CEO Dick Costolo has said tweets aren’t the attraction, they’re what leads you to content. Twitter aims to be a key distributor of media and info. Add the addition of former News Corp. President Peter Chernin to the board, and their hashtag landing page experience for events, and their media behemoth ambitions get pretty clear. There are challenges ahead and Costolo has also laid those out; entry into China, figuring out how to have Twitter deliver both comprehensive and relevant, targeted experiences, and the visualization of big data. What does this mean for corporations? They can expect a more media-rich evolution and growing emphases on imagery. They can expect more opportunities to create great media content and leverage Twitter for its distribution. And they can expect new ways to surface in searches. Are brands diving in? 56% of customer tweets to companies get completely and totally ignored. Ugh. A study Twitter recently conducted with Compete shows people who see tweets from retailers are more likely to buy a product. And, the more retailer tweets they see, the more likely they are to purchase on the retail site. As more of those tweets point to engaging media content from the brand, the results should get even better. Twitter appears ready for 2013. Enterprise brands have some work to do. @mikestilesPhoto Stuart Miles, freedigitalphotos.net

  Read the article

• Running a home mail server using dynamic dns [closed]

  - by Anand

  Hi, Is it possible to run an email server on my home box using dynamic dns? The scenario is, I want to auto cc all incoming and outgoing emails from my one account to another, from some server side config instead of configuring email clients for rules. I have tried Google Apps Mail but it doesn't allow auto cc of outgoing emails. After having read tons of blogs, forum messages etc (hope I have been reading the correct info :) ) the only option to achieve what I am needing is to setup my own mail server, but the cost of getting a static IP doesn't fit my budget. Please can someone point me in the correct direction. Platform doesn't matter, I can setup a Windows or Linux server. Many Thanks

  Read the article

• Android: how do I switch between game scenes in a game? Any tutorials?

  - by Flavio

  I am trying to create a simple game using the Android SDK without using AndEngine (or any other game engine). I have plenty of experience designing games from the past, but I'm having lots of trouble trying to use the Android SDK to make my game. By far my biggest hurdle right now is switching between views. That is, for example, going from the menu to the first level, etc. I am using a traditional model I learned (I think it's called a scene stack or something?) in which you push the current scene onto a stack and the game's main loop runs the top item of the stack. This model seems non-trivial to implement in the Android SDK, mostly because Android seems to be picky about which thread instantiates which view. My issue is that I want the first level to show up when you press a button on the main menu, but when I instantiate the first level (the level class extends SurfaceView and implements SurfaceHolder.Callback) I get a runtime error complaining that the thread that runs the main menu can't instantiate this class. Something about calling Looper.prepare(). I figured at this point I was probably doing things wrong. I'm not sure how to specifically phrase my issue into a question, so maybe I should leave it as either 1) Does anybody know a good way (or the 'proper' way) to switch between scenes in an Android game? or 2) Are there any tutorials out there which show how to create a game that doesn't take place entirely in one scene? (I have googled for a while to no avail... maybe someone else knows of one?) Thanks!

  Read the article

• How to handle Real Time Data from a database perspective?

  - by balexandre

  I have an idea in mind, but it still confuses me the database area. Imagine that I want to show real time data, and using one of the latest browser technologies (web sockets - even using older browsers) it is very easy to show to all observables (user browser) what everyone is doing. Remy Sharp has an example about the simplicity about this. But I still don't get the database part, how would I feed, let's imagine (using Remy game Tron) that I want to save the path for each connected user in a database and if a client wants to see what is going on with a 5 sec delay, he will see that, not only the 5 sec until that moment but the continuation in time ... how can I query a DB like that? SELECT x, y FROM run WHERE time >= DATEADD(second, -5, rundate); is not the recommended path right? and pulling this x in x time ... this is not real data feed correct? If can someone help me understand the Database point of view, I would greatly appreciate.

  Read the article

• Are there currently any modern, standardized, aptitude test for software engineering?

  - by Matthew Patrick Cashatt

  Background I am a working software engineer who is in the midst of seeking out a new contract for the next year or so. In my search, I am enduring several absurd technical interviews as indicated by this popular question I asked earlier today. Even if the questions I was being asked weren't almost always absurd, I would be tired nonetheless of answering them many times over for various contract opportunities. So this got me thinking that having a standardized exam that working software professionals could take would provide a common scorecard that could be referenced by interviewers in lieu of absurd technical interview questions (i.e. nerd hazing). Question Is there a standardized software engineering aptitude test (SEAT??) available for working professionals to take? If there isn't a such an exam out there, what questions or topics should be covered? An additional thought Please keep in mind, if suggesting a question or topic, to focus on questions or topics that would be relevant to contemporary development practices and realistic needs in the workforce as that would be the point of a standard aptitude test. In other words, no clown traversal questions.

  Read the article

• CodePlex Daily Summary for Thursday, July 31, 2014

  CodePlex Daily Summary for Thursday, July 31, 2014Popular ReleasesDbEntry.Net (Leafing Framework): DbEntry.Net 4.2: DbEntry.Net is a lightweight Object Relational Mapping (ORM) database access compnent for .Net 4.0+. It has clearly and easily programing interface for ORM and sql directly, and supoorted Access, Sql Server, MySql, SQLite, Firebird, PostgreSQL and Oracle. It also provide a Ruby On Rails style MVC framework. Asp.Net DataSource and a simple IoC. DbEntry.Net.v4.2.Setup.zip include the setup package. DbEntry.Net.v4.2.Src.zip include source files and unit tests. DbEntry.Net.v4.2.Samples.zip ...Recaptcha for .NET: Recaptcha for .NET v1.5: What's NewMinor bug fixes Support for legacy .NET framework 4.0 and ASP.NET MVC 4. Support for .NET Framework 4.5.1.Azure Storage Explorer: Azure Storage Explorer 6 Preview 1: Welcome to Azure Storage Explorer 6 Preview 1 This is the first release of the latest Azure Storage Explorer, code-named Phoenix. What's New?Here are some important things to know about version 6: Open Source Now being run as a full open source project. Full source code on CodePlex. Collaboration encouraged! Updated Code Base Brand-new code base (WPF/C#/.NET 4.5) Visual Studio 2013 solution (previously VS2010) Uses the Task Parallel Library (TPL) for asynchronous background operat...Wsus Package Publisher: release v1.3.1407.29: Updated WPP to recognize the very latest console version. Some files was missing into the latest release of WPP which lead to crash when trying to make a custom update. Add a workaround to avoid clipboard modification when double-clicking on a label when creating a custom update. Add the ability to publish detectoids. (This feature is still in a BETA phase. Packages relying on these detectoids to determine which computers need to be updated, may apply to all computers).VG-Ripper & PG-Ripper: PG-Ripper 1.4.32: changes NEW: Added Support for 'ImgMega.com' links NEW: Added Support for 'ImgCandy.net' links NEW: Added Support for 'ImgPit.com' links NEW: Added Support for 'Img.yt' links FIXED: 'Radikal.ru' links FIXED: 'ImageTeam.org' links FIXED: 'ImgSee.com' links FIXED: 'Img.yt' linksDynamics AX Development tools: Version 1.0.0: Alpha release of the package. I am just combining greate community tools into a package. I have not go through testing every function of the tools. However, feel free to point out if you found any bugs!Asp.Net MVC-4,Entity Framework and JQGrid Demo with Todo List WebApplication: Asp.Net MVC-4,Entity Framework and JQGrid Demo: Asp.Net MVC-4,Entity Framework and JQGrid Demo with simple Todo List WebApplication, Overview TodoList is a simple web application to create, store and modify Todo tasks to be maintained by the users, which comprises of following fields to the user (Task Name, Task Description, Severity, Target Date, Task Status). TodoList web application is created using MVC - 4 architecture, code-first Entity Framework (ORM) and Jqgrid for displaying the data.Waterfox: Waterfox 31.0 Portable: New features in Waterfox 31.0: Added support for Unicode 7.0 Experimental support for WebCL New features in Firefox 31.0:New Add the search field to the new tab page Support of Prefer:Safe http header for parental control mozilla::pkix as default certificate verifier Block malware from downloaded files Block malware from downloaded files audio/video .ogg and .pdf files handled by Firefox if no application specified Changed Removal of the CAPS infrastructure for specifying site-sp...SuperSocket, an extensible socket server framework: SuperSocket 1.6.3: The changes below are included in this release: fixed an exception when collect a server's status but it has been stopped fixed a bug that can cause an exception in case of sending data when the connection dropped already fixed the log4net missing issue for a QuickStart project fixed a warning in a QuickStart projectYnote Classic: Ynote Classic 2.8.5 Beta: Several Changes - Multiple Carets and Multiple Selections - Improved Startup Time - Improved Syntax Highlighting - Search Improvements - Shell Command - Improved StabilityHead First C#: The Quest: The Quest: Stable release of "The Quest" game ( Lab 2 from Head First C#, 3rd edition)TCP/IP Adapter BizTalk 2013: TCPIP Adapter for BizTalk 2013 - Version 1.0: Version 1.0 This is an updated version of the BizTalk 2010 TCP/IP adapter. References have been updated and a new setup (ISLE) has been used. Follow the installation instructions below to install the adapter. Still want to automate step 4, but haven't got to it yet. Installation instructions Make sure to close the BizTalk Administration Console. Just to make sure everything gets refreshed after installation. Download and install the setup. The setup makes sure the adapter will be regis...gicon: gicon HTTP service v1.0.0: core: 1.0.0.26592 service: 1.0.0.27190 Github: http://rynnwang.github.io/gicon/ Github.io: http://rynnwang.github.io/gicon/ Codeplex: http://gicon.codeplex.com .NET required: 2.0 or above. Installation notes: 1. You need to run intallutil command to install ifunction.GuidIconHttpService.exe file as Windows Service 2. You need to update ifunction.GuidIconHttpService.exe.config file in the folder to set correct HTTP URI prefixes. In release zip by default, it is set as http://localhost:20000...TEBookConverter: 1.2: Fixed: Could not start convertion in some cases Fixed: Progress show during convertion was truncated Fixed: Stopping convertion didn't reset program titlenewmail_OutlookCOM: newmail_OutlookCOM: First Stable ReleaseSharePoint - Data View Web Part Documenter: Data View Web Part Documenter 1.0: .NET Framework 4 Client Profile required for this to run on your PC. Please see the documentation for running the tool.LOL zmena skinu klienta: LOL jednoduchý menic skinu klienta: Jednoduchý prográmek, který ušetrí cas pri zmene klienta. Nemusí se proklikáva18541855 adresáru :)SSRS Plus+: Latest - SSRS Plus Application and Source Code: This release contains the Beta version with significant changes in comparison to the old release which I am keeping for legacy reasons. At some point a changeover will be made once it has been confirmed that my branch is stable and Mr Bagwan is in agreement also.CS-Script Source: Release v3.8.4: CSScript.Evaluator is migrated to Mono v3.3.0 Added aggregating //css_ignore_ns from the imported scripts cs-script.7z - CS-Script Suite (binaries, documentation, samples) cs-script.ExtensionPack.7z - CS-Script Extension Pack (additional binaries and samples) cs-scriptDocs.7z - CS-Script DocumentationDotSpatial: DotSpatial 1.7: DotSpatial.Full - includes all DotSpatial libraries, extensions and DemoMap application DotSpatial.Core - includes only DotSpatial core libraries Entire list of changes see in the issue tracker. Main changes: Improved common stability, optimized memory and speed when loading and rendering shapefiles, fixed some memory leaks in rasters and shape layers. Simplified plugin infrastructure. Now there are predefined implementations for all required components (IStatusControl, IDockManager, IHead...New ProjectsBrilliantORM: ????ORM??，??SQL?????????。???????????。Crafter: ?????? ??? ????Dotnetnuke xblog // Blog, Article, Events, Documents: xBlog is a blog program based on DNN, it has powerful functions and unique design style. In addition to article management function which common blog module hasIn Plain Sight: Embedding plain text into an image so one can hide the text "In Plain Sight". A cursory view into the world of Steganography.JS Koans Visual Studio Friendly Version: A Version of JS koans loaded into Visual StudioMy Troop First: just adding to the siteOFX Parser: Biblioteca desenvolvida em C# que traduz arquivos OFX e gera a instância de uma classe que representa o arquivo. Um exemplo de uso está disponível, assim como aOrchard Custom Code module: This module adds a very simple tool to add custom code in front-end pages head and foot.SPB Export to KeePass Import Conversion: A simple script to convert the .xml-file by konste's "SPB Wallet Export" (https://spbwalletexport.codeplex.com/) into an import format accepted by KeePass 2The unTroublemaker: The unTroublemaker is a troubleshooter program that helps your project quickly find and fix missing dependency issues using simple XML-based specifications.

  Read the article

• Fill a table from a RAND based formula in Excel 2010

  - by Greg Reynolds

  I am trying to do a Monte Carlo simulation using Excel, but a lot of the tutorials I have found are either for older versions of the product, or are not quite what I am after. A simple example of the kind of think I am after is: Cell A1 contains the formula to simulate (for example int(6*rand())+1 to simulate rolling a dice). I have 10 rows of "Trials". What I want is to somehow point each row at a different calculation of the formula in A1. So I would end up with something like Trial Value 1 2 2 5 3 6 4 2 5 1 6 3 7 2 8 4 9 2 10 1 I have tried playing with some of the "What-if Analysis" tools, but I am a bit lost.

  Read the article

• Output to TV only works if monitor is plugged in

  - by Greg Sansom

  I am trying to use my TV as the sole output for a computer. The computer has a graphics card with 2 outputs - one RGB and one DVI. I have the RGB output going to the TV, and when the DVI output is connected to a monitor, display works fine on both the monitor and the TV. If I turn off the monitor, or even turn off power to the monitor, the TV continues to display the desktop. If I unplug the DVI cable from the monitor (remember that the monitor doesn't have any power at this point), the TV stops presenting the desktop and displays a "Not Accepted" message. When starting up the computer, the TV displays fine, but stops working at the "press ctrl-alt-delete" screen unless the monitor is connected. How can I make the TV show the display without the monitor? The TV is an LG RT-42PZ45V. The graphics card is an ATI Radeon series HD4350 512MB GDDR2. The computer is running Windows Server 2008 r2.

  Read the article

< Previous Page | 568 569 570 571 572 573 574 575 576 577 578 579  | Next Page >