Search Results

Search found 22281 results on 892 pages for 'password management'.

Page 574/892 | < Previous Page | 570 571 572 573 574 575 576 577 578 579 580 581  | Next Page >

• got VPN l2l connect between a site & HQ but not traffice using ASA5505 on both ends

  - by vinlata

  Hi, Could anyone see what did I do wrong here? this is one configuration of site1 to HQ on ASA5505, I can get connected but seems like no traffic going (allowed) between them, could it be a NAT issue? any helps would much be appreciated Thanks interface Vlan1 nameif inside security-level 100 ip address 172.30.205.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address pppoe setroute ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 shutdown ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 shutdown ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! passwd .dIuXDIYzD6RSHz7 encrypted ftp mode passive dns server-group DefaultDNS domain-name errg.net object-group network HQ network-object 172.22.0.0 255.255.0.0 network-object 172.22.0.0 255.255.128.0 network-object 172.22.0.0 255.255.255.128 network-object 172.22.1.0 255.255.255.128 network-object 172.22.1.0 255.255.255.0 access-list inside_access_in extended permit ip any any access-list outside_access_in extended permit icmp any any echo-reply access-list outside_20_cryptomap extended permit ip 172.30.205.0 255.255.255.0 o bject-group HQ access-list inside_nat0_outbound extended permit ip 172.30.205.0 255.255.255.0 o bject-group HQ access-list policy-nat extended permit ip 172.30.205.0 255.255.255.0 172.22.0.0 255.255.0.0 pager lines 24 logging asdm informational mtu inside 1500 mtu outside 1500 icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 nat-control global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) 172.30.205.0 access-list policy-nat access-group inside_access_in in interface inside access-group outside_access_in in interface outside timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout uauth 0:05:00 absolute username errgadmin password Os98gTdF8BZ0X2Px encrypted privilege 15 http server enable http 64.42.2.224 255.255.255.240 outside http 172.22.0.0 255.255.0.0 outside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto map outside_map 190 match address outside_20_cryptomap crypto map outside_map 190 set pfs crypto map outside_map 190 set peer 66.7.249.109 crypto map outside_map 190 set transform-set ESP-3DES-SHA crypto map outside_map 190 set phase1-mode aggressive crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 30 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 crypto isakmp policy 65535 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 crypto isakmp nat-traversal 190 crypto isakmp ipsec-over-tcp port 10000 tunnel-group 66.7.249.109 type ipsec-l2l tunnel-group 66.7.249.109 ipsec-attributes pre-shared-key * telnet timeout 5 ssh 172.30.205.0 255.255.255.0 inside ssh 172.22.0.0 255.255.0.0 outside ssh 64.42.2.224 255.255.255.240 outside ssh 172.25.0.0 255.255.128.0 outside ssh timeout 5 console timeout 0 management-access inside vpdn group PPPoEx request dialout pppoe vpdn group PPPoEx localname [email protected] vpdn group PPPoEx ppp authentication pap vpdn username [email protected] password ********* dhcpd address 172.30.205.100-172.30.205.131 inside dhcpd dns 172.22.0.133 68.94.156.1 interface inside dhcpd wins 172.22.0.133 interface inside dhcpd domain errg.net interface inside dhcpd enable inside ! ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect netbios inspect rsh inspect rtsp inspect skinny inspect esmtp inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp ! end

  Read the article

• Lockdown users on Windows Server 2012

  - by el.severo

  I set up a Active Directory on a server machine with Windows Server 2012 and I'd like to create some users with limitations like Windows Steady State does in Windows XP (locally). Seen already the Windows SteadyState Handbook (with Windows Server 2008), but I'd like to know if anyone has tried this before, the limitations are the following: 1. Prevent locked or roaming user profiles that cannot be found on the computer from logging on 2. Do not cache copies of locked or roaming user profiles for users who have previously logged on to this computer 3. Do not allow Windows to compute and store passwords using LAN Manager Hash values 4. Do not store usernames or passwords used to log on to the Windows Live ID or the domain 5. Prevent users from creating folders and files on drive C:\ 6. Lock profile to prevent the user from making permanent changes 7. Remove the Control Panel, Printer and Network Settings from the Classic Start menu 8. Remove the Favorites icon 9. Remove the My Network Places icon 10. Remove the Frequently Used Program list 11. Remove the Shared documents folder from My Computer 12. Remove control Panel icon 13. Remove the Set Program Access and Defaults icon 14. Remove the Network Connection(Connect To)icon 15. Remove the Printers and Faxes icon 16. Remove the Run icon 17. Prevent access to Windows Explorer features: Folder Options, Customize Toolbar, and the Notification Area 18. Prevent access to the taskbar 19. Prevent access to the command prompt 20. Prevent access to the registry editor 21. Prevent access to the Task Manager 22. Prevent access to Microsoft Management Console utilities 23. Prevent users from adding or removing printers 24. Prevent users from locking the computer 25. Prevent password changes (also requires the Control Panel icon to be removed) 26. Disable System Tools and other management programs 27. Prevent users from saving files to the desktop 28. Hide A Drive 29. Hide B Drive 30. Hide C Drive 31. Prevent changes to Internet Explorer registry settings 32. Empty the Temporary Internet Files folder when Internet Explorer is closed 33. Remove Internet Options 34. Remove General tab in Internet Options 35. Remove Security tab in Internet Options 36. Remove Privacy tab in Internet Options 37. Remove Content tab in Internet Options 38. Remove Connections tab in Internet Options 39. Remove Programs tab in Internet Options 40. Remove Advanced tab in Internet Options 41. Set a home page (Internet Explorer) 42. Restrict the possibility to change desktop image 43. Restrict the possibility to change wallpaper 44. Restrict usb flash drives Any suggestions for this? UPDATE: As @Dan suggested me I'd like to specify that would be applied to a educational scenario where students can login from a computer and want to add some restrictions to them.

  Read the article

• How To Start Your Own Professional Blog with WordPress

  - by Matthew Guay

  Would you like to start your own blog or website?  With a free WordPress  account, it’s free and easy to get started creating your own professional quality blog site. This is the first part in a series on how to create your own professional quality blog site. No, we’re not talking about some cheapo looking blog from Blogger or something on Facebook, but creating a quality blog you can be proud of and present to millions of readers online. WordPress is one of the most popular blogging platforms, powering hundreds of high-profile websites and blogs around the world.  It’s both powerful and easy to use, which makes it great whether you’re just starting out or are a blogging pro.  To start out with your blogging project WordPress is completely free, and you can use the online interface or install the WordPress software on your own server and blog from there. Getting Started You can start a blog in just a few minutes.  Head over to WordPress.com and click Sign up now on the right-hand side of the main page. Enter a username and password, check that you agree with the legal terms, select the “Gimme a blog” bullet, and click Next. WordPress may inform you that your username is already taken, simply choose a new one and try again. Next, choose a domain for your blog.  This will be the address for your site, and cannot be changed, so be sure to choose exactly what you want.  If you’d prefer your address to be yourname.com instead of yourname.wordpress.com, you can add your own domain for a fee after your blog is setup…but we’ll cover that later. Once you click signup, you will be sent a confirmation email.  While you wait for the email to arrive you can go ahead and enter in your name and a short bio about yourself. When you receive your confirmation email, click the link.  Congratulations; you now have your own blog! You can view your new blog immediately, though the default theme isn’t very interesting without your content and pictures. Back on the page you opened from the email, click Login to access your blog’s administration page and to start adding stuff to your blog.  You can also access your blog’s admin page anytime by from yourname.wordpress.com/admin, substituting your own blog name for yourname. Enter your username and password, then click Log in to get started. Adding Content to your WordPress.com Blog When you sign in to your WordPress blog, you’ll first see the WordPress Admin page.  Here you can see recent posts and comments, and you can see stats of how many people have visited your site.  You can also access all of your blog tools and settings right from this page. To add a new post to your blog, click the Posts link on the left, then click “Add New” either on the left menu or on the top of the Edit Posts page.  Or, if you want to edit the default first post, hover over it and select Edit. Or click the New Posts button on the top of the page.  This menu bar is always visible whenever you’re logged in, so it’s an easy way to add a post. The editor lets you easily write anything you want in a Microsoft Word-style editor.  You can format your text, add lists, links, quotes, and more.  When you’re ready to share your content with the world, click Publish on the right side. To add pictures or other files, click the picture icon beside “Upload/Insert”.  Your free blog account can store up to 3Gb of pictures and documents which will definitely give you a good start. Click Select Files, and then choose the pictures or documents you want to add to your post. When the pictures have uploaded, you can add a caption and choose how to position the picture.  When you’re finished, select “Insert into Post”.   Or, if you want to add a video, click the video button.  You have to add a paid upgrade to upload videos directly, but you can add YouTube and other online videos for free. Click the “From URL” tab, and then paste the link to the YouTube video and click Insert into post. If you’re a code geek, click the HTML tab in the editor and edit the HTML of your blog post the geeky way. Once you’ve added all your content and edited it the way you want, click the Publish button on the right of the editor.  Or, you can click Preview to make sure it looks right, and then click Publish. Here’s our blog with the new blog post containing a picture and video.  While you’re getting to know you’re way around the controls in WordPress, the Preview feature will be your best friend while you try to organize the content to your liking.   Conclusion It only takes a couple minutes to get started blogging at WordPress.com. Whether you want to write about your daily life, share pictures of your children, or review the latest books and gadgets, WordPress.com is a great place to get started for free.  But we’ve only covered a small portion of the WordPress features…but this should get you started. Check back for more WordPress and blogging coverage coming up soon! Links Signup for a free WordPress.com account Similar Articles Productive Geek Tips Add Social Bookmarking (Digg This!) Links to your Wordpress BlogHow-To Geek SoftwareProtecting Your WordPress Admin Panel From Hackers With .htaccessMake a Backup Copy of your Production Wordpress Blog on UbuntuLinux QuickTip: Downloading and Un-tarring in One Step TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Awe inspiring, inter-galactic theme (Win 7) Case Study – How to Optimize Popular Wordpress Sites Restore Hidden Updates in Windows 7 & Vista Iceland an Insurance Job? Find Downloads and Add-ins for Outlook Recycle !

  Read the article

• Integrate SharePoint 2010 with Team Foundation Server 2010

  - by Martin Hinshelwood

  Our client is using a brand new shiny installation of SharePoint 2010, so we need to integrate our upgraded Team Foundation Server 2010 instance into it. In order to do that you need to run the Team Foundation Server 2010 install on the SharePoint 2010 server and choose to install only the “Extensions for SharePoint Products and Technologies”. We want out upgraded Team Project Collection to create any new portal in this SharePoint 2010 server farm. There a number of goodies above and beyond a solution file that requires the install, with the main one being the TFS2010 client API. These goodies allow proper integration with the creation and viewing of Work Items from SharePoint a new feature with TFS 2010. This works in both SharePoint 2007 and SharePoint 2010 with the level of integration dependant on the version of SharePoint that you are running. There are three levels of integration with “SharePoint Services 3.0” or “SharePoint Foundation 2010” being the lowest. This level only offers reporting services framed integration for reporting along with Work Item Integration and document management. The highest is Microsoft Office SharePoint Services (MOSS) Enterprise with Excel Services integration providing some lovely dashboards. Figure: Dashboards take the guessing out of Project Planning and estimation. Plus writing these reports would be boring!   The Extensions that you need are on the same installation media as the main TFS install and the only difference is the options you pick during the install. Figure: Installing the TFS 2010 Extensions for SharePoint Products and Technologies onto SharePoint 2010   Annoyingly you may need to reboot a couple of times, but on this server the process was MUCH smother than on our internal server. I think this was mostly to do with this being a clean install. Once it is installed you need to run the configuration. This will add all of the Solution and Templates that are needed for SharePoint to work properly with TFS. Figure: This is where all the TFS 2010 goodies are added to your SharePoint 2010 server and the TFS 2010 object model is installed.   Figure: All done, you have everything installed, but you still need to configure it Now that we have the TFS 2010 SharePoint Extensions installed on our SharePoint 2010 server we need to configure them both so that they will talk happily to each other. Configuring the SharePoint 2010 Managed path for Team Foundation Server 2010 In order for TFS to automatically create your project portals you need a wildcard managed path setup. This is where TFS will create the portal during the creation of a new Team project. To find the managed paths page for any application you need to first select the “Managed web applications”  link from the SharePoint 2010 Central Administration screen. Figure: Find the “Manage web applications” link under the “Application Management” section. On you are there you will see that the “Managed Paths” are there, they are just greyed out and selecting one of the applications will enable it to be clicked. Figure: You need to select an application for the SharePoint 2010 ribbon to activate.   Figure: You need to select an application before you can get to the Managed Paths for that application. Now we need to add a managed path for TFS 2010 to create its portals under. I have gone for the obvious option of just calling the managed path “TFS02” as the TFS 2010 server is the second TFS server that the client has installed, TFS 2008 being the first. This links the location to the server name, and as you can’t have two projects of the same name in two separate project collections there is unlikely to be any conflicts. Figure: Add a “tfs02” wildcard inclusion path to your SharePoint site. Configure the Team Foundation Server 2010 connection to SharePoint 2010 In order to have you new TFS 2010 Server talk to and create sites in SharePoint 2010 you need to tell the TFS server where to put them. As this TFS 2010 server was installed in out-of-the-box mode it has a SharePoint Services 3.0 (the free one) server running on the same box. But we want to change that so we can use the external SharePoint 2010 instance. Just open the “Team Foundation Server Administration Console” and navigate to the “SharePoint Web Applications” section. Here you click “Add” and enter the details for the Managed path we just created. Figure: If you have special permissions on your SharePoint you may need to add accounts to the “Service Accounts” section.    Before we can se this new SharePoint 2010 instance to be the default for our upgraded Team Project Collection we need to configure SharePoint to take instructions from our TFS server. Configure SharePoint 2010 to connect to Team Foundation Server 2010 On your SharePoint 2010 server open the Team Foundation Server Administration Console and select the “Extensions for SharePoint Products and Technologies” node. Here we need to “grant access” for our TFS 2010 server to create sites. Click the “Grant access” link and  fill out the full URL to the  TFS server, for example http://servername.domain.com:8080/tfs, and if need be restrict the path that TFS sites can be created on. Remember that when the users create a new team project they can change the default and point it anywhere they like as long as it is an authorised SharePoint location. Figure: Grant access for your TFS 2010 server to create sites in SharePoint 2010 Now that we have an authorised location for our team project portals to be created we need to tell our Team Project Collection that this is where it should stick sites by default for any new Team Projects created. Configure the Team Foundation Server 2010 Team Project Collection to create new sites in SharePoint 2010 Back on out TFS 2010 server we need to setup the defaults for our upgraded Team Project Collection to the new SharePoint 2010 integration we have just set up. On the TFS 2010 server open up the “Team Foundation Server Administration Console” again and navigate to the “Team Project Collections” node. Once you are there you will see a list of all of your TPC’s and in our case we have a DefaultCollection as well as out named and Upgraded collection for TFS 2008. If you select the “SharePoint Site” tab we can see that it is not currently configured. Figure: Our new Upgrade TFS2008 Team Project Collection does not have SharePoint configured Select to “Edit Default Site Location” and select the new integration point that we just set up for SharePoint 2010. Once you have selected the “SharePoint Web Application” (the thing we just configured) then it will give you an example based on that configuration point and the name of the Team Project Collection that we are configuring. Figure: Set the default location for new Team Project Portals to be created for this Team Project Collection This is where the reason for configuring the Extensions on the SharePoint 2010 server before doing this last bit becomes apparent. TFS 2010 is going to create a site at our http://sharepointserver/tfs02/ location called http://sharepointserver/tfs02/[TeamProjectCollection], or whatever we had specified, and it would have had difficulty doing this if we had not given it permission first. Figure: If there is no Team Project Collection site at this location the TFS 2010 server is going to create one This will create a nice Team Project Collection parent site to contain the Portals for any new Team Projects that are created. It is with noting that it will not create portals for existing Team Projects as this process is run during the Team Project Creation wizard. Figure: Just a basic parent site to host all of your new Team Project Portals as sub sites   You will need to add all of the users that will be creating Team Projects to be Administrators of this site so that they will not get an error during the Project Creation Wizard. You may also want to customise this as a proper portal to your projects if you are going to be having lots of them, but it is really just a default placeholder so you have a top level site that you can backup and point at. You have now integrated SharePoint 2010 and team Foundation Server 2010! You can now go forth and multiple your Team Projects for this Team Project Collection or you can continue to add portals to your other Collections.   Technorati Tags: TFS 2010,Sharepoint 2010,VS ALM

  Read the article

• Installing Lubuntu 14.04.1 forcepae fails

  - by Rantanplan

  I tried to install Lubuntu 14.04.1 from a CD. First, I chose Try Lubuntu without installing which gave: ERROR: PAE is disabled on this Pentium M (PAE can potentially be enabled with kernel parameter "forcepae" ... Following the description on https://help.ubuntu.com/community/PAE, I used forcepae and tried Try Lubuntu without installing again. That worked fine. dmesg | grep -i pae showed: [ 0.000000] Kernel command line: file=/cdrom/preseed/lubuntu.seed boot=casper initrd=/casper/initrd.lz quiet splash -- forcepae [ 0.008118] PAE forced! On the live-CD session, I tried installing Lubuntu double clicking on the install button on the desktop. Here, the CD starts running but then stops running and nothing happens. Next, I rebooted and tried installing Lubuntu directly from the boot menu screen using forcepae again. After a while, I receive the following error message: The installer encountered an unrecoverable error. A desktop session will now be run so that you may investigate the problem or try installing again. Hitting Enter brings me to the desktop. For what errors should I search? And how? Finally, I rebooted once more and tried Check disc for defects with forcepae option; no errors have been found. Now, I am wondering how to find the error or whether it would be better to follow advice c in https://help.ubuntu.com/community/PAE: "Move the hard disk to a computer on which the processor has PAE capability and PAE flag (that is, almost everything else than a Banias). Install the system as usual but don't add restricted drivers. After the install move the disk back." Thanks for some hints! Perhaps some of the following can help: On Lubuntu 12.04: cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 13 model name : Intel(R) Pentium(R) M processor 1.50GHz stepping : 6 microcode : 0x17 cpu MHz : 600.000 cache size : 2048 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr mce cx8 mtrr pge mca cmov clflush dts acpi mmx fxsr sse sse2 ss tm pbe up bts est tm2 bogomips : 1284.76 clflush size : 64 cache_alignment : 64 address sizes : 32 bits physical, 32 bits virtual power management: uname -a Linux humboldt 3.2.0-67-generic #101-Ubuntu SMP Tue Jul 15 17:45:51 UTC 2014 i686 i686 i386 GNU/Linux lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 12.04.5 LTS Release: 12.04 Codename: precise cpuid eax in eax ebx ecx edx 00000000 00000002 756e6547 6c65746e 49656e69 00000001 000006d6 00000816 00000180 afe9f9bf 00000002 02b3b001 000000f0 00000000 2c04307d 80000000 80000004 00000000 00000000 00000000 80000001 00000000 00000000 00000000 00000000 80000002 20202020 20202020 65746e49 2952286c 80000003 6e655020 6d756974 20295228 7270204d 80000004 7365636f 20726f73 30352e31 007a4847 Vendor ID: "GenuineIntel"; CPUID level 2 Intel-specific functions: Version 000006d6: Type 0 - Original OEM Family 6 - Pentium Pro Model 13 - Stepping 6 Reserved 0 Brand index: 22 [not in table] Extended brand string: " Intel(R) Pentium(R) M processor 1.50GHz" CLFLUSH instruction cache line size: 8 Feature flags afe9f9bf: FPU Floating Point Unit VME Virtual 8086 Mode Enhancements DE Debugging Extensions PSE Page Size Extensions TSC Time Stamp Counter MSR Model Specific Registers MCE Machine Check Exception CX8 COMPXCHG8B Instruction SEP Fast System Call MTRR Memory Type Range Registers PGE PTE Global Flag MCA Machine Check Architecture CMOV Conditional Move and Compare Instructions FGPAT Page Attribute Table CLFSH CFLUSH instruction DS Debug store ACPI Thermal Monitor and Clock Ctrl MMX MMX instruction set FXSR Fast FP/MMX Streaming SIMD Extensions save/restore SSE Streaming SIMD Extensions instruction set SSE2 SSE2 extensions SS Self Snoop TM Thermal monitor 31 reserved TLB and cache info: b0: unknown TLB/cache descriptor b3: unknown TLB/cache descriptor 02: Instruction TLB: 4MB pages, 4-way set assoc, 2 entries f0: unknown TLB/cache descriptor 7d: unknown TLB/cache descriptor 30: unknown TLB/cache descriptor 04: Data TLB: 4MB pages, 4-way set assoc, 8 entries 2c: unknown TLB/cache descriptor On Lubuntu 14.04.1 live-CD with forcepae: cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 13 model name : Intel(R) Pentium(R) M processor 1.50GHz stepping : 6 microcode : 0x17 cpu MHz : 600.000 cache size : 2048 KB physical id : 0 siblings : 1 core id : 0 cpu cores : 1 apicid : 0 initial apicid : 0 fdiv_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov clflush dts acpi mmx fxsr sse sse2 ss tm pbe bts est tm2 bogomips : 1284.68 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 32 bits virtual power management: uname -a Linux lubuntu 3.13.0-32-generic #57-Ubuntu SMP Tue Jul 15 03:51:12 UTC 2014 i686 i686 i686 GNU/Linux lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 14.04.1 LTS Release: 14.04 Codename: trusty cpuid CPU 0: vendor_id = "GenuineIntel" version information (1/eax): processor type = primary processor (0) family = Intel Pentium Pro/II/III/Celeron/Core/Core 2/Atom, AMD Athlon/Duron, Cyrix M2, VIA C3 (6) model = 0xd (13) stepping id = 0x6 (6) extended family = 0x0 (0) extended model = 0x0 (0) (simple synth) = Intel Pentium M (Dothan B1) / Celeron M (Dothan B1), 90nm miscellaneous (1/ebx): process local APIC physical ID = 0x0 (0) cpu count = 0x0 (0) CLFLUSH line size = 0x8 (8) brand index = 0x16 (22) brand id = 0x16 (22): Intel Pentium M, .13um feature information (1/edx): x87 FPU on chip = true virtual-8086 mode enhancement = true debugging extensions = true page size extensions = true time stamp counter = true RDMSR and WRMSR support = true physical address extensions = false machine check exception = true CMPXCHG8B inst. = true APIC on chip = false SYSENTER and SYSEXIT = true memory type range registers = true PTE global bit = true machine check architecture = true conditional move/compare instruction = true page attribute table = true page size extension = false processor serial number = false CLFLUSH instruction = true debug store = true thermal monitor and clock ctrl = true MMX Technology = true FXSAVE/FXRSTOR = true SSE extensions = true SSE2 extensions = true self snoop = true hyper-threading / multi-core supported = false therm. monitor = true IA64 = false pending break event = true feature information (1/ecx): PNI/SSE3: Prescott New Instructions = false PCLMULDQ instruction = false 64-bit debug store = false MONITOR/MWAIT = false CPL-qualified debug store = false VMX: virtual machine extensions = false SMX: safer mode extensions = false Enhanced Intel SpeedStep Technology = true thermal monitor 2 = true SSSE3 extensions = false context ID: adaptive or shared L1 data = false FMA instruction = false CMPXCHG16B instruction = false xTPR disable = false perfmon and debug = false process context identifiers = false direct cache access = false SSE4.1 extensions = false SSE4.2 extensions = false extended xAPIC support = false MOVBE instruction = false POPCNT instruction = false time stamp counter deadline = false AES instruction = false XSAVE/XSTOR states = false OS-enabled XSAVE/XSTOR = false AVX: advanced vector extensions = false F16C half-precision convert instruction = false RDRAND instruction = false hypervisor guest status = false cache and TLB information (2): 0xb0: instruction TLB: 4K, 4-way, 128 entries 0xb3: data TLB: 4K, 4-way, 128 entries 0x02: instruction TLB: 4M pages, 4-way, 2 entries 0xf0: 64 byte prefetching 0x7d: L2 cache: 2M, 8-way, sectored, 64 byte lines 0x30: L1 cache: 32K, 8-way, 64 byte lines 0x04: data TLB: 4M pages, 4-way, 8 entries 0x2c: L1 data cache: 32K, 8-way, 64 byte lines extended feature flags (0x80000001/edx): SYSCALL and SYSRET instructions = false execution disable = false 1-GB large page support = false RDTSCP = false 64-bit extensions technology available = false Intel feature flags (0x80000001/ecx): LAHF/SAHF supported in 64-bit mode = false LZCNT advanced bit manipulation = false 3DNow! PREFETCH/PREFETCHW instructions = false brand = " Intel(R) Pentium(R) M processor 1.50GHz" (multi-processing synth): none (multi-processing method): Intel leaf 1 (synth) = Intel Pentium M (Dothan B1), 90nm

  Read the article

• Generating a twitter OAuth access key - the semi-manual way

  - by Piet

  [UPDATE] Apparently someone at Twitter was listening, or I’m going senile/blind. Let’s call it a combination of both. Instead of following all the steps below, you could just login with the Twitter account you want to use on http://dev.twitter.com, register your application and then click ‘Edit Details’ on the application overview page at http://dev.twitter.com/apps. Next click the ‘Application detail’ button on the right, followed by the ‘My Access Token’ button in order to get your Access Token and Access Token Secret. This makes the old post below rather obsolete. Clearly a case of me thinking everything is a nail and ruby is a hammer (don’t they usually say this about java coders?) [ORIGINAL POST] OAuth is great! OAuth allows your application to use your user’s data without the need to ask for their password. So Twitter made the API much safer for their and your users. Hurray! Free pizza for everyone! Unless of course you’re using the Twitter API for your own needs like running your own bot and don’t need access to other user’s data. In such cases a simple username/password combination is more than enough. I can understand however that the Twitter guys don’t really care that much about these exceptions(?). Most such uses for the API are probably rather spammy in nature. !!! If you have a twitter app that uses the API to access external user’s data: look for another solution. This solution is ONLY meant when you ONLY need access to your own account(s) through the API. Other Solutions Mr Dallas Devries posted a solution here which involves requesting and scraping a one-time PIN. But: I like to minimize the amount of calls I make to twitter’s API or pages to lessen my chances of meeting the fail whale. Also, as soon as the pin isn’t included in a div called ‘oauth_pin’ anymore, this will fail. However, mr Devries’ post was a starting point for my solution, so I’m much obliged to him posting his findings. Authenticating with the Twitter API: old vs new Acessing The Twitter API the old way: require ‘twitter’ httpauth = Twitter::HTTPAuth.new('my_account','my_secret_password') client = Twitter::Base.new(httpauth) client.update(‘Hurray!’) The OAuth way: require 'twitter' oauth = Twitter::OAuth.new('ve4whatafuzzksaMQKjoI', 'KliketyklikspQ6qYALcuNandsomemored8pQ6qYALIG7mbEQY') oauth.authorize_from_access('123-owhfmeyAgfozdyt5hDeprSevsWmPo5rVeroGfsthis', 'fGiinCdqtehMeehiddenymDeAsasaawgGeryye8amh') client = Twitter::Base.new(oauth) client.update(‘Hurray!’) In the above case, ve4whatafuzzksaMQKjoI is the ‘consumer key’ (sometimes also referred to as ‘consumer token’) and KliketyklikspQ6qYALcuNandsomemored8pQ6qYALIG7mbEQY is the ‘consumer secret’. You’ll get these from Twitter when you register your app. 123-owhfmeyAgfozdyt5hDeprSevsWmPo5rVeroGfsthis is the ‘access token’ and fGiinCdqtehMeehiddenymDeAsasaawgGeryye8amh is the ‘access secret’. This combination gives the registered application access to your account. I’ll show you how to obtain these by following the steps below. (Basically you’ll need a bunch of keys and you’ll have to jump a bit through hoops to obtain them for your server/bot. ) How to get these keys 1. Surf to the twitter apps registration page go to http://dev.twitter.com/apps to register your app. Login with your twitter account. 2. Register your application Enter something for Application name, Description, website,… as I said: they make you jump through hoops. If you plan on using the API to post tweets, Your application name and website will be used in the ‘5 minutes ago via…’ line below your tweet. You could use the this to point to a page with info about your bot, or maybe it’s useful for SEO purposes. For application type I choose ‘browser’ and entered http://www.hadermann.be/callback as a ‘Callback URL’. This url returns a 404 error, which is ideal because after giving our account access to our ‘application’ (step 6), it will redirect to this url with an ‘oauth_token’ and ‘oauth_verifier’ in the url. We need to get these from the url. It doesn’t really matter what you enter here though, you could leave it blank because you need to explicitely specify it when generating a request token. You probably want read&write access so set this at ‘Default Access type’. 3. Get your consumer key and consumer secret On the next page, copy/paste your ‘consumer key’ and ‘consumer secret’. You’ll need these later on. You also need these as part of the authentication in your script later on: oauth = Twitter::OAuth.new([consumer key], [consumer secret]) 4. Obtain your request token run the following in IRB to obtain your ‘request token’ Replace my fake consumer key and consumer secret with the one you obtained in step 3. And use something else instead http://www.hadermann.be/callback: although this will only give a 404, you shouldn’t trust me. irb(main):001:0> require 'oauth' irb(main):002:0> c = OAuth::Consumer.new('ve4whatafuzzksaMQKjoI', 'KliketyklikspQ6qYALcuNandsomemored8pQ6qYALIG7mbEQY', {:site => 'http://twitter.com'}) irb(main):003:0> request_token = c.get_request_token(:oauth_callback => 'http://www.hadermann.be/callback') irb(main):004:0> request_token.token => "UrperqaukeWsWt3IAlfbxzyBUFpwWIcWkHP94QH2C1" This (UrperqaukeWsWt3IAlfbxzyBUFpwWIcWkHP94QH2C1) is the request token: Copy/paste this token, you will need this next. 5. Authorize your application surf to https://api.twitter.com/oauth/authorize?oauth_token=[the above token], for example: https://api.twitter.com/oauth/authorize?oauth_token=UrperqaukeWsWt3IAlfbxzyBUFpwWIcWkHP94QH2C1 This will bring you to the ‘An application would like to connect to your account’- screen on Twitter where you can grant access to the app you just registered. If you aren’t still logged in, you need to login first. Click ‘Allow’. Unless you don’t trust yourself. 6. Get your oauth_verifier from the redirected url Your browser will be redirected to your callback url, with an oauth_token and oauth_verifier parameter appended. You’ll need the oauth_verifier. In my case the browser redirected to: http://www.hadermann.be/callback?oauth_token=UrperqaukeWsWt3IAlfbxzyBUFpwWIcWkHP94QH2C1&oauth_verifier=waoOhKo8orpaqvQe6rVi5fti4ejr8hPeZrTewyeag Which returned a 404, giving me the chance to copy/paste my oauth_verifier: waoOhKo8orpaqvQe6rVi5fti4ejr8hPeZrTewyeag 7. Request an access token Back to irb, use the oauth_verifier to request an access token, as follows: irb(main):005:0> at = request_token.get_access_token(:oauth_verifier => 'waoOhKo8orpaqvQe6rVi5fti4ejr8hPeZrTewyeag') irb(main):006:0> at.params[:oauth_token] => "123-owhfmeyAgfozdyt5hDeprSevsWmPo5rVeroGfsthis" irb(main):007:0> at.params[:oauth_token_secret] => "fGiinCdqtehMeehiddenymDeAsasaawgGeryye8amh" We’re there! 123-owhfmeyAgfozdyt5hDeprSevsWmPo5rVeroGfsthis is the access token. fGiinCdqtehMeehiddenymDeAsasaawgGeryye8amh is the access secret. Try it! Try the following to post an update: require 'twitter' oauth = Twitter::OAuth.new('ve4whatafuzzksaMQKjoI', 'KliketyklikspQ6qYALcuNandsomemored8pQ6qYALIG7mbEQY') oauth.authorize_from_access('123-owhfmeyAgfozdyt5hDeprSevsWmPo5rVeroGfsthis', 'fGiinCdqtehMeehiddenymDeAsasaawgGeryye8amh') client = Twitter::Base.new(oauth) client.update(‘Cowabunga!’) Now you can go to your twitter page and delete the tweet if you want to.

  Read the article

• Create a Bootable Ubuntu 9.10 USB Flash Drive

  - by Trevor Bekolay

  The Ubuntu Live CD isn’t just useful for trying out Ubuntu before you install it, you can also use it to maintain and repair your Windows PC. Even if you have no intention of installing Linux, every Windows user should have a bootable Ubuntu USB drive on hand in case something goes wrong in Windows. Creating a bootable USB flash drive is surprisingly easy with a small self-contained application called UNetbootin. It will even download Ubuntu for you! Note: Ubuntu will take up approximately 700 MB on your flash drive, so choose a flash drive with at least 1 GB of free space, formatted as FAT32. This process should not remove any existing files on the flash drive, but to be safe you should backup the files on your flash drive. Put Ubuntu on your flash drive UNetbootin doesn’t require installation; just download the application and run it. Select Ubuntu from the Distribution drop-down box, then 9.10_Live from the Version drop-down box. If you have a 64-bit machine, then select 9.10_Live_x64 for the Version. At the bottom of the screen, select the drive letter that corresponds to the USB drive that you want to put Ubuntu on. If you select USB Drive in the Type drop-down box, the only drive letters available will be USB flash drives. Click OK and UNetbootin will start doing its thing. First it will download the Ubuntu Live CD. Then, it will copy the files from the Ubuntu Live CD to your flash drive. The amount of time it takes will vary depending on your Internet speed, an when it’s done, click on Exit. You’re not planning on installing Ubuntu right now, so there’s no need to reboot. If you look at the USB drive now, you should see a bunch of new files and folders. If you had files on the drive before, they should still be present. You’re now ready to boot your computer into Ubuntu 9.10! How to boot into Ubuntu When the time comes that you have to boot into Ubuntu, or if you just want to test and make sure that your flash drive works properly, you will have to set your computer to boot off of the flash drive. The steps to do this will vary depending on your BIOS – which varies depending on your motherboard. To get detailed instructions on changing how your computer boots, search for your motherboard’s manual (or your laptop’s manual for a laptop). For general instructions, which will suffice for 99% of you, read on. Find the important keyboard keys When your computer boots up, a bunch of words and numbers flash across the screen, usually to be ignored. This time, you need to scan the boot-up screen for a few key words with some associated keys: Boot menu and Setup. Typically, these will show up at the bottom of the screen. If your BIOS has a Boot Menu, then read on. Otherwise, skip to the Hard: Using Setup section. Easy: Using the Boot Menu If your BIOS offers a Boot Menu, then during the boot-up process, press the button associated with the Boot Menu. In our case, this is ESC. Our example Boot Menu doesn’t have the ability to boot from USB, but your Boot Menu should have some options, such as USB-CDROM, USB-HDD, USB-FLOPPY, and others. Try the options that start with USB until you find one that works. Don’t worry if it doesn’t work – you can just restart and try again. Using the Boot Menu does not change the normal boot order on your system, so the next time you start up your computer it will boot from the hard drive as normal. Hard: Using Setup If your BIOS doesn’t offer a Boot Menu, then you will have to change the boot order in Setup. Note: There are some options in BIOS Setup that can affect the stability of your machine. Take care to only change the boot order options. Press the button associated with Setup. In our case, this is F2. If your BIOS Setup has a Boot tab, then switch to it and change the order such that one of the USB options occurs first. There may be several USB options, such as USB-CDROM, USB-HDD, USB-FLOPPY, and others; try them out to see which one works for you. If your BIOS does not have a boot tab, boot order is commonly found in Advanced CMOS Options. Note that this changes the boot order permanently until you change it back. If you plan on only plugging in a bootable flash drive when you want to boot from it, then you could leave the boot order as it is, but you may find it easier to switch the order back to the previous order when you reboot from Ubuntu. Booting into Ubuntu If you set the right boot option, then you should be greeted with the UNetbootin screen. Press enter to start Ubuntu with the default options, or wait 10 seconds for this to happen automatically. Ubuntu will start loading. It should go straight to the desktop with no need for a username or password. And that’s it! From this live desktop session, you can try out Ubuntu, and even install software that is not included in the live CD. Installed software will only last for the duration of your session – the next time you start up the live CD it will be back to its original state. Download UNetbootin from sourceforge.net Similar Articles Productive Geek Tips Create a Bootable Ubuntu USB Flash Drive the Easy WayReset Your Ubuntu Password Easily from the Live CDHow-To Geek on Lifehacker: Control Your Computer with Shortcuts & Speed Up Vista SetupHow To Setup a USB Flash Drive to Install Windows 7Speed up Your Windows Vista Computer with ReadyBoost TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional New Stinger from McAfee Helps Remove ‘FakeAlert’ Threats Google Apps Marketplace: Tools & Services For Google Apps Users Get News Quick and Precise With Newser Scan for Viruses in Ubuntu using ClamAV Replace Your Windows Task Manager With System Explorer Create Talking Photos using Fotobabble

  Read the article

• Getting Started with Boxee

  - by DigitalGeekery

  Boxee is a free Media PC application that runs on Windows, Mac, and Ubuntu Linux. With Boxee, you can integrate online video, music and pictures, with your own local media and social networking. Today we are going to take a closer look at Boxee and some of it’s features. Note: We used Windows 7 for this tutorial. Your experience on a Mac or Ubuntu Linux build may vary slightly. Hardware Requirements x86 (Intel/AMD processor) based system running at 1.0GHz or greater 512MB system memory (RAM) or more Video card capable of OpenGL 1.4, Direct X 9.0 Software Requirements Mac OS X 10.4+ (Intel based processor) Ubuntu Linux 9.04+ x86 only Windows XP / Vista / 7 (64 bit in Vista or 7) Installing Boxee Before downloading and installing Boxee, you’ll need to register for a free account. (See link below) Once your account is registered and verified, you’ll be able to log in and download the application. Installation is pretty straightforward…just take the defaults. Boxee will open in full screen mode and you’ll be prompted to login with your username and password. Before you login, you may want to take a moment to click on the “Guide” icon and learn a bit about navigating in Boxee. Some basic keyboard navigation is as follows. Move right, left, up, & down with the arrow keys. Hit “Enter” to make a selection, the forward slash key “\” to toggle between full screen and windowed mode, and “Esc” to go back to the previous screen. For Playback, the volume is controlled by plus & minus (+/-) keys, you can Play / Pause using the spacebar, and skip using the arrow keys. Boxee will also work with any infrared remote. If you have an iPhone or iPod Touch you can download software to enable them as a Boxee remote. If you’re using a mouse and keyboard, hover over the username and password boxes to enter your login credentials. If using a a remote, click your OK button and enter credentials with the on screen keyboard. Click “Done” when finished.   When you are ready to login, enter your credentials and click “Login.” On first login, you’ll be prompted to calibrate your screen. If you choose “Skip” you can always calibrate your screen later under Settings > Appearance > Screen. When Boxee opens, you’ll be greeted by the Home screen. To the left will be your Feeds. This will be any recommended content from friends on Boxee, and social networks such as Facebook and Twitter. Although, when you first login, it will mainly be info from the Boxee staff. You’ll have “Featured” content in the center and your Queue on the right. You’ll also have the Menu along the top.   Pop Up Menu The Pop Menu can be accessed by hitting the “Esc” key, or back on your remote. Depending on where you are located in Boxee, you may have to hit it a few time to “back out” to the Pop Up menu. From the Pop Up Menu, you can easily access any of the resources, settings, and favorites. Queue The Queue is your playlist of TV shows, movies, or Internet videos you wish to watch. When you find an offering you’d like to watch, select it and then click “Add to Queue.” The selected item will be added to your Queue and can be accessed at any time from the Menu. TV Show Library The TV Show library can contain files from your local hard drive or streaming content from the Web. Boxee pulls content from a variety of online locations such as Hulu and TV network sites. Click on the show to see which specific episodes are currently available. To search for your favorite shows, click on the yellow arrow to the left, or navigate to the left with your keyboard or remote. Enter your selection into the search box. My Apps By default, the “My Apps” section includes a list of the most popular apps, such as Netflix, Pandora, YouTube, and others. You can remove Apps from “My Apps,” or add new Apps from the Apps Library.   To access all the available Apps, click on the left arrow button, or click on the yellow arrow at the left, then select “App Library.” Choose an App from the Library and click it to open… … and then select “Add to My Apps.” Or, you can click start to play the App if you don’t wish to Add it to your “My Apps.”   Music, Pictures, and Movies Boxee will scan your PC for movies, pictures, and music. You can choose to scan specific folders by clicking on “Scan Media Folders…” … or from the Pop Up Menu, selecting Settings > Media, and then browsing for your media.   Conclusion Boxee to be a great way to integrate your local media with online streaming content. It can be run as an application on your home PC, or as a stand alone media PC. It should also be noted, however, that your access to online content will vary depending on your country. If you are a Windows Media Center user and and want to add the additional features of Boxee, check out our article on integrating Boxee with Windows 7 Media Center. Download Boxee Similar Articles Productive Geek Tips Integrate Boxee with Media Center in Windows 7Disable Fast User Switching on Windows XPOops! Sorry About the Feed ErrorsDisplay a list of Started Services from the Command Line (Windows)Feedburner to Google: Worst Transition Ever. TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Discover New Bundled Feeds in Google Reader Play Music in Chrome by Simply Dragging a File 15 Great Illustrations by Chow Hon Lam Easily Sync Files & Folders with Friends & Family Amazon Free Kindle for PC Download Stretch popurls.com with a Stylish Script (Firefox)

  Read the article

• Top Tweets SOA Partner Community – March 2012

  - by JuergenKress

  Send your tweets @soacommunity #soacommunity and follow us at http://twitter.com/soacommunity SOA Community ?SOA Community Newsletter February 2012 wp.me/p10C8u-o0 Marc ?Reading through the #OFM 11.1.1.6 , patchset 5 documentation. What is the best way to upgrade your whole dev…prd street. SOA Community Thanks for the successful and super interesting #sbidays ! Wonderful discussions around the Integration, case management and security tracks Torsten Winterberg Schon den neuen Opitz Technology-Blog gebookmarked? The Cattle Crew bit.ly/yLPwBD wird ab sofort regelmäßig Erkenntnisse posten. OTNArchBeat ? Unit Testing Asynchronous BPEL Processes Using soapUI | @DanielAmadei bit.ly/x9NsS9 Rolando Carrasco ?Video de Human Task en BPM 11g. Por @edwardo040. bit.ly/wki9CA cc @OracleBPM @OracleSOA @soacommunity View video Marcel Mertin SOA Security Hands-On by Dirk Krafzig and Mamoon Yunus at #sbidays is also great! SOA Community Workshop day #sbidays #BPMN2.0 by Volker Stiehl from #SAP great training – now I can model & execute in #bpmsuite #soacommunity Simone Geib ?Just updated our advanced #soasuite #otn page with a number of very interesting @orclateamsoa blog posts: bit.ly/advancedsoasui… OTNArchBeat ? Start Small, Grow Fast: SOA Best Practices article by @biemond, @rluttikhuizen, @demed bit.ly/yem9Zv Steffen Miller ? Nice new features in SOA Suite Business Rules #PS5 Testing rules with scenarios and output validation bit.ly/zj64Q3 @SOACOMMUNITY OTNArchBeat ? Reply SOA Blackbelt training by David Shaffer, April 30th–May 4th 2012 bit.ly/xGdC24 OTNArchBeat ? What have BPM, big data, social tools, and business models got in common? | Andy Mulholland bit.ly/xUkOGf SOA Community ? Live hacking at #sbidays – cheaper shopping, bias cracking, payment systems, secure your SOA! pic.twitter.com/y7YaIdug SOA Community Future #BPM & #ACM solutions can make use of ontology’s, based on #sqarql #sbidays pic.twitter.com/xLb1Z5zs Simone Geib ? @soacommunity: SOA Blackbelt training by David Shaffer, April 30th–May 4th 2012 wp.me/p10C8u-nX Biemond Changing your ADF Connections in Enterprise Manager with PS5: With Patch Set 5 of Fusion Middleware you can fina… bit.ly/zF7Rb1 Marc ? HUGE (!) CPU and Heap improvement on Oracle Fusion Middleware tinyurl.com/762drzp @wlscommunity @soacommunity #OSB #SOA #WLS SOA Community ?Networking @ SOA & BPM Partner Community blogs.oracle.com/soacommunity/e… #soacommunity #otn #opn #oracle SOA Community ?Published the SOA Partner Community newsletter February edition – READ it. Not yet a member? oracle.com/goto/emea/soa #soacommunity #otn #opn AMIS, Oracle & Java Blog by Lucas Jellema: "Book Review: Do More with SOA Integration: Best of Packt (december 2011, various authors)" bit.ly/wq633E Jon petter hjulstad @SOASimone Excellent summary! Lots of new features! Simone Geib ?Do you want to know what’s new in #soasuite #PS5? Go to bit.ly/xBX06f and let me know what you think SOA Community ? Unit Testing Asynchronous BPEL Processes Using soapUI oracle.com/technetwork/ar… #soacommunity #soa #otn #oracle #bpel Retweeted by SOA Community View media Retweeted by SOA Community Eric Elzinga ? Oracle Fusion Middleware Partner Community Forum Malage, The Overview, bit.ly/AA9BKd #ofmforum SOA&Cloud Symposium ? The February issue of the Service Technology Magazine is now published. servicetechmag.com SOA Community ? Oracle SOA Suite 11g Database Growth Management – must read! oracle.com/technetwork/da… #soacommunity #soa #purging demed ? Have you exposed internal processes to mobile devices using #oraclesoa? Interested in an article? DM me! #osb #rest #multichannel #mobile orclateamsoa ? A-Team SOA Blog: Enhanced version of Thread Dump Analyzer (TDA A-Team) ow.ly/1hpk7l SOA Community Reply BPM Suite #PS5 (11.1.1.6) available for download soacommunity.wordpress.com/2012/02/22/soa… Send us your feedback! #soacommunity #bpmsuite #opn SOA Community ? SOA Suite #PS5 (11.1.1.6) available for download soacommunity.wordpress.com/2012/02/22/soa… Send us your feedback! #soacommunity #soasuite SOA Community BPM Suite #PS5 1(1.1.1.6) available for download. List of new BPM features blogs.oracle.com/soacommunity/e… #soacommunity #bpm #bpmsuite #opn OracleBlogs BPM in Utilties Industry ow.ly/1hC3fp Retweeted by SOA Community OTNArchBeat ? Demystifying Oracle Enterprise Gateway | Naresh Persaud bit.ly/xtDNe2 OTNArchBeat ? Architect’s Guide to Big Data; Test BPEL Processes Using SoapUI; Development Debate bit.ly/xbDYSo Frank Nimphius ? Finished my book review of "Do More with SOA Integration: Best of Packt ". Here are my review comments: bit.ly/x2k9OZ Lucas Jellema ? That is my one stop-and-go download center for #PS5 : edelivery.oracle.com/EPD/Download/g… Lucas Jellema ? Interesting piece of documentation: Fusion Applications Extensibility Guide – docs.oracle.com/cd/E15586_01/f… source for design time @ run time inspira Lucas Jellema ? Strongly improved support for testing Business Rules at Design Time in #PS5 see docs.oracle.com/cd/E23943_01/u… Lucas Jellema ? SOA Suite 11gR1 PS5: new BPEL Component testing – docs.oracle.com/cd/E23943_01/d… Lucas Jellema ? PS5 available for CEP (Complex Event Processing) – a personal favorite of mine : oracle.com/technetwork/mi… Lucas Jellema ?What’s New in Fusion Developer’s Guide 11gR1 PS5: docs.oracle.com/cd/E23943_01/w… Lucas Jellema ? BPMN Correlation (FMW 11gR1 PS5): docs.oracle.com/cd/E23943_01/d… Lucas Jellema ? Modifying running BPM Process instances (FMW 11gR1 PS5): docs.oracle.com/cd/E23943_01/d… Lucas Jellema ? SOA Suite 11gR1 PS5 – new aggregation pattern: docs.oracle.com/cd/E23943_01/d… routing multiple messages to same instance Melvin van der Kuijl ? Automating Testing of SOA Composite Applications in PS5. docs.oracle.com/cd/E23943_01/d… Cato Aune ? SOA suite PS5 Enterprise Deployment Guide is available in ePub docs.oracle.com/cd/E23943_01/c… . Much better than pdf on Galaxy Note SOA Community ?JDeveloper 11.1.1.6 is available for download bit.ly/wGYrwE #soacommunity SOA Community ? Your first experience #PS5 – let us know @soacommunity – send us your tweets and blog posts! #soacommunity Jon petter hjulstad ? WLS 10.3.6 New features, ex better logging of jdbc use: docs.oracle.com/cd/E23943_01/w… Heidi Buelow ? Get it now! RT @soacommunity: BPM Suite PS5 11.1.1.6 available for download bit.ly/AgagT5 #bpm #soacommunity Jon petter hjulstad ?SOA Suite PS5 EDG contains OSB! docs.oracle.com/cd/E23943_01/c… Jon petter hjulstad ? Testing Oracle Rules from JDeveloper is easier in PS5: docs.oracle.com/cd/E23943_01/u… Biemond® ? What’s New in Oracle Service Bus 11.1.1.6.0 oracle.com/technetwork/mi… Jon petter hjulstad ? Adminguide New and Changed Features for PS5, ex GridLink data sources: docs.oracle.com/cd/E23943_01/c… Retweeted by SOA Community Andreas Koop ? Unbelievable! #OFM Doc Lib growth from 11gPS4->11gPS5 by 1.2G! View media SOA Community ?ODI PS5 is available oracle.com/technetwork/mi… #odi #soacommunity 22 Feb View media SOA Community Service Bus 11g Development Cookbook soacommunity.wordpress.com/2012/02/20/ser… #osb #soacommunity #ace #opn View media For regular information on Oracle SOA Suite become a member in the SOA Partner Community for registration please visit  www.oracle.com/goto/emea/soa (OPN account required) Blog Twitter LinkedIn Mix Forum Technorati Tags: soacommunity,twitter,Oracle,SOA Community,Jürgen Kress,OPN,SOA,BPM

  Read the article

• Install Ubuntu Netbook Edition with Wubi Installer

  - by Matthew Guay

  Ubuntu is one of the most popular versions of Linux, and their Netbook Remix edition is especially attractive for netbook owners.  Here we’ll look at how you can easily try out Ubuntu on your netbook without a CD/DVD drive. Netbooks, along with the growing number of thin, full powered laptops, lack a CD/DVD drive.  Installing software isn’t much of a problem since most programs, whether free or for-pay, are available for download.  Operating systems, however, are usually installed from a disk.  You can easily install Windows 7 from a flash drive with our tutorial, but installing Ubuntu from a USB flash drive is more complicated.  However, using Wubi, a Windows installer for Ubuntu, you can easily install it directly on your netbook and even uninstall it with only a few clicks. Getting Started Download and run the Wubi installer for Ubuntu (link below).  In the installer, select the drive you where you wish to install Ubuntu, the size of the installation (this is the amount dedicated to Ubuntu; under 20Gb should be fine), language, username, and desired password.  Also, from the Desktop environment menu, select Ubuntu Netbook to install the netbook edition.  Click Install when your settings are correct. Wubi will automatically download the selected version of Ubuntu and install it on your computer. Windows Firewall may ask if you want to unblock Wubi; select your network and click Allow access. The download will take around an hour on broadband, depending on your internet connection speed.  Once the download is completed, it will automatically install to your computer.  If you’d prefer to have everything downloaded before you start the install, download the ISO of Ubuntu Netbook edition (link below) and save it in the same folder as Wubi. Then, when you run Wubi, select the netbook edition as before and click Install.  Wubi will verify that your download is valid, and will then proceed to install from the downloaded ISO.  This install will only take about 10 minutes. Once the install is finished you will be asked to reboot your computer.  Save anything else you’re working on, and then reboot to finish setting up Ubuntu on your netbook. When your computer reboots, select Ubuntu at the boot screen.  Wubi leaves the default OS as Windows 7, so if you don’t select anything it will boot into Windows 7 after a few seconds. Ubuntu will automatically finish the install when you boot into it the first time.  This took about 12 minutes in our test. When the setup is finished, your netbook will reboot one more time.  Remember again to select Ubuntu at the boot screen.  You’ll then see a second boot screen; press your Enter key to select the default.   Ubuntu only took less than a minute to boot in our test.  When you see the login screen, select your name and enter your password you setup in Wubi.  Now you’re ready to start exploring Ubuntu Netbook Remix. Using Ubuntu Netbook Remix Ubuntu Netbook Remix offers a simple, full-screen interface to take the best advantage of netbooks’ small screens.  Pre-installed applications are displayed in the application launcher, and are organized by category.  Click once to open an application. The first screen on the application launcher shows your favorite programs.  If you’d like to add another application to the favorites pane, click the plus sign beside its icon. Your files from Windows are still accessible from Ubuntu Netbook Remix.  From the home screen, select Files & Folders on the left menu, and then click the icon that says something like 100GB Filesystem under the Volumes section. Now you’ll be able to see all of your files from Windows.  Your user files such as documents, music, and pictures should be located in Documents and Settings in a folder with your user name. You can also easily install a variety of free applications via the Software Installer. Connecting to the internet is also easy, as Ubuntu Netbook Remix automatically recognized the WiFi adaptor on our test netbook, a Samsung N150.  To connect to a wireless network, click the wireless icon on the top right of the screen and select the network’s name from the list. And, if you’d like to customize your screen, right-click on the application launcher and select Change desktop background. Choose a background picture you’d like. Now you’ll see it through your application launcher.  Nice! Most applications are opened full-screen.  You can close them by clicking the x on the right of the program’s name. You can also switch to other applications from their icons on the top left.  Open the home screen by clicking the Ubuntu logo in the far left. Changing Boot Options By default, Wubi will leave Windows as the default operating system, and will give you 10 seconds at boot to choose to boot into Ubuntu.  To change this, boot into Windows and enter Advanced system settings in your start menu search. In this dialog, click Settings under Startup and Recovery. From this dialog, you can select the default operating system and the time to display list of operating systems.  You can enter a lower number to make the boot screen appear for less time. And if you’d rather make Ubuntu the default operating system, select it from the drop-down list.   Uninstalling Ubuntu Netbook Remix If you decide you don’t want to keep Ubuntu Netbook Remix on your computer, you can uninstall it just like you uninstall any normal application.  Boot your computer into Windows, open Control Panel, click Uninstall a Program, and enter ubuntu in the search box.  Select it, and click Uninstall. Click Uninstall at the prompt.  Ubuntu uninstalls very quickly, and removes the entry from the bootloader as well, so your computer is just like it was before you installed it.   Conclusion Ubuntu Netbook Remix offers an attractive Linux interface for netbooks.  We enjoyed trying it out, and found it much more user-friendly than most Linux distros.  And with the Wubi installer, you can install it risk-free and try it out on your netbook.  Or, if you’d like to try out another alternate netbook operating system, check out our article on Jolicloud, another new OS for netbooks. Links Download Wubi Installer for Windows Download Ubuntu Netbook Edition Similar Articles Productive Geek Tips Easily Install Ubuntu Linux with Windows Using the Wubi InstallerInstall VMware Tools on Ubuntu Edgy EftHow to install Spotify in Ubuntu 9.10 using WineInstalling PHP5 and Apache on UbuntuInstalling PHP4 and Apache on Ubuntu TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips VMware Workstation 7 Acronis Online Backup DVDFab 6 Revo Uninstaller Pro Explorer++ is a Worthy Windows Explorer Alternative Error Goblin Explains Windows Error Codes Twelve must-have Google Chrome plugins Cool Looking Skins for Windows Media Player 12 Move the Mouse Pointer With Your Face Movement Using eViacam Boot Windows Faster With Boot Performance Diagnostics

  Read the article

• 17 new features in Visual Studio 2010

  - by vik20000in

  Visual studio 2010 has been released to RTM a few days back. This release of Visual studio 2010 comes with a big number of improvements on many fronts. In this post I will try and point out some of the major improvements in Visual Studio 2010. 1)      Visual studio IDE Improvement. Visual studio IDE has been rewritten in WPF. The look and feel of the studio has been improved for improved readability. Start page has been redesigned and template so that anyone can change the start page as they wish. 2)      Multiple Monitor - Support for Multiple Monitor was already there in Visual studio. But in this edition it has been improved as much that we can now place the document, design and code window outside the IDE in another monitor. 3)      ZOOM in Code Editor – Making the editors in WPF has made significant improvement for them. The best one that I like is the ZOOM feature. We can now zoom in the code editor with the help of the ctrl + Mouse scroll. The zoom feature does not work on the Design surface or windows with icon like solution view and toolbox. 4)      Box Selection - Another Important improvement in the Visual studio 2010 is the box selection. We can select a rectangular by holding down the Alt Key and selecting with mouse.  Now in the rectangular selection we can insert text, Paste same code in different line etc. This is helpful if you want to convert a number of variables from public to private etc… 5)      New Improved Search – One of the best productivity improvements in Visual studio 2010 is its new search as you type support. This has been done in the Navigate To window which can be brought up by pressing (Ctrl + ,). The navigate To windows also take help of the Camel casing and will be able to search with the help of camel casing when character is entered in upper case. For example we can search AOH for AddOrederHeader. 6)      Call Hierarchy – This feature is only available to the Visual C# and Visual C++ editor. The call hierarchy windows displays the calls made to and from (yes both to and from) a selected method property or a constructor. The call hierarchy also shows the implementation of interface and the overrides of virtual or abstract methods. This window is very helpful in understanding the code flow, and evaluating the effect of making changes. The best part is it is available at design time and not at runtime only like a debugger. 7)      Highlighting references – One of the very cool stuff in Visual Studio 2010 is the fact if you select a variable then all the use of that variable will be highlighted alongside. This should work for all the result of symbols returned by Find all reference. This also works for Name of class, objects variable, properties and methods. We can also use the Ctrl + Shift + Down Arrow or Up Arror to move through them. 8)      Generate from usage - The Generate from usage feature lets you use classes and members before you define them. You can generate a stub for any undefined class, constructor, method, property, field, or enum that you want to use but have not yet defined. You can generate new types and members without leaving your current location in code, This minimizes interruption to your workflow.9)      IntelliSense Suggestion Mode - IntelliSense now provides two alternatives for IntelliSense statement completion, completion mode and suggestion mode. Use suggestion mode for situations where classes and members are used before they are defined. In suggestion mode, when you type in the editor and then commit the entry, the text you typed is inserted into the code. When you commit an entry in completion mode, the editor shows the entry that is highlighted on the members list. When an IntelliSense window is open, you can press CTRL+ALT+SPACEBAR to toggle between completion mode and suggestion mode. 10)   Application Lifecycle Management – A client application for management of application lifecycle like version control, work item tracking, build automation, team portal etc is available for free (this is not available for express edition.). 11)   Start Page – The start page has been redesigned with WPF for new functionality and look. Tabbed areas are provided for content from different source including MSDN. Once you open some project the start page closes automatically. The list of recent project also lets you remove project from the list. And above all the start page is customizable enough to be changed as per individual requirement. 12)   Extension Manager – Visual Studio 2010 has provided good ways to be extended. We can also use MEF to extend most of the features of Visual Studio. The new extension manager now can go the visual studio gallery and install the extension without even opening any explorer. 13)   Code snippets – Visual studio 2010 for HTML, Jscript and Asp.net also. 14)   Improved Intelligence for JavaScript has been improved vastly (around 2-5 times). Intelligence now also shows the XML documentation comment on the go. 15)   Web Deployment – Web Deployment has been vastly improved. We can package and publish the web application in one click. Three major supported deployment scenarios are Web packages, one click deployment and Web configuration Transformation. 16)   SharePoint - Visual Studio 2010 also brings vastly improved development experience for SharePoint. We can create, edit, debug, package, deploy and activate SharePoint project from within Visual Studio. Deployment of Site is as easy as hitting F5. 17)   Azure – Visual Studio 2010 also comes with handy improvement for developing on windows Azure environment. Vikram

  Read the article

• Tools to Help Post Content On Your WordPress Blog

  - by Matthew Guay

  Now that you’ve got a nice blog, you want to do more with it and start posting content.  Here we look at some tools that will allow you to post directly to your WordPress blog. Writing a new blog post is easy with WordPress as we saw in our previous post about Starting your own WordPress blog.  The web editor gives you a lot of features and even lets you edit your post’s source code if you enjoy hacking HTML.  There are other tools that will allow you to post content, here we look at how you can post with dedicated apps, browser plugins, and even by email. Windows Live Writer Windows Live Writer (part of the Windows Live Essentials Suite) is a great app for posting content to your blog.  This free program for Microsoft lets you post content to a variety of blogging services, including Blogger, Typepad, LiveJournal, and of course WordPress.  You can write blog posts directly from its Word-like editor, complete with pictures and advanced formatting.  Even if you’re offline, you can still write posts and save them for when you’re online again. For more information about installing Live writer, check out our article on how to Install Windows Live Essentials In Windows 7. Once Live Writer is installed, open it to add your blog.  If you already had Live Writer installed and configured for a blog, you can add your new blog, too.  Just click your blog’s name in the top right corner, and select “Add blog account”. Select “Other blog service” to add your WordPress blog to Writer, and click Next.   Enter your blog’s web address, and your username and password.  Check Remember my password so you don’t have to enter it every time you write something. Writer will analyze your blog and setup your account. During the setup process it may ask to post a temporary post.  This will let you preview blog posts using your blog’s real theme, which is helpful, so click Yes. Finally, add your Blog’s name, and click Finish. You can now use the rich editor to write and add content to a new blog post.   Select the Preview tab to see how your post will look on your blog… Or, if you’re a HTML geek, select the Source tab to edit the code of your blog post. From the bottom of the window, you can choose categories, insert tags, and even schedule the post to publish on a different day.  Live Writer is fully integrated with WordPress; you’re not missing anything by using the desktop editor. If you want to edit a post you’ve already published, click the Open button and select the post.  You can chose and edit any post, including ones you published via the web interface or other editors. Add Multimedia Content to your Posts with Live Writer Back in the Edit tab, you can add pictures, videos and more from the sidebar.  Select what you want to insert. Pictures If you insert a picture, you can add many nice borders and designs to it. Or, you can even add artistic effects from the Effects tab in the sidebar. Photo Gallery If you want to post several pictures, say some of your vacation shots, then inserting a picture gallery may be the best option.  Select Insert Photo Gallery in the sidebar, and then choose the pictures you want in the gallery. Once the gallery is inserted, you can choose from several styles to showcase your pictures. When you post the blog, you will be asked to sign in with your Windows Live ID as the gallery pictures will be stored in the free Skydrive storage service. Your blog readers can see the preview of your pictures directly on your blog, and then can view each individual picture, download them, or see a slideshow online via the link. Video If you want to add a video to your blog post, select Video from the sidebar as above.  You can select a video that’s already online, or you can choose a new video from file and upload it via YouTube directly from Windows Live Writer.   Note that you will have to sign in with your YouTube account to upload videos to YouTube, so if you’re not logged in you’ll be prompted to do so when you click Insert. Geek Tip:  If you ever want to copy your Live Writer settings to another computer, check out our article on how to Backup Your Windows Live Writer Settings. Microsoft Office Word Word 2007 and 2010 also let you post content directly to your blog.  This is especially nice if you’ve already typed up a document and think it would be good on your Blog as well.  Check out our in-depth tutorial on posting blog posts via Word 2007 using Word 2007 as a blogging tool. This works in Word 2010 too, except the Office Orb has been replaced by the new Backstage view.  So, in Word 2010, to start a new blog post, click File \ New then select Blog post.  Proceed as you would in Word 2007 to add your blog settings and post the content you want. Or, if you’ve already written a document and want to post it, select File \ Share (or Save and Send in the final version of Word 2010), and then click Publish as Blog Post.  If you haven’t setup your blog account yet, set it up as shown in the Word 2007 article. Post Via Email Most of us use email daily, and already have our favorite email app or service.  Whether on your desktop or mobile phone, it’s easy to create rich emails and add content.  WordPress lets you generate a unique email address that you can use to easily post content and email to your blog.  Just compose your email with the subject as the title of your post, and send it to this unique address.  Your new post will be up in minutes. To active this feature, click the My Account button in the top menu bar in your WordPress.com account, and select My Blogs. Click the Enable button under Post by Email beside your blog’s name.   Now you’ll have a private email you can use to post to your blog.  Anything you send to this email will be posted as a new post.  If you think your email may be compromised, click Regenerate to get a new publishing email address. Any email program or webapp now is a blog post editor.  Feel free to use rich formatting or insert pictures; it all comes through great.  This is also a great way to post to your blog from your mobile device.  Whether you’re using webmail or a dedicated email client on your phone, you can now blog from anywhere.   Mobile Applications WordPress also offer dedicated applications for blogging directly from your mobile device.  You can write new posts, edit existing ones, and manage comments all from your Smartphone.  Currently they offer apps for iPhone, Android, and Blackberry.  Check them out at the link below. Conclusion Whether you want to write from your browser or email a post to your blog, WordPress is flexible enough to work right along with your preferences.  However you post, you can be sure that it will look professional and be easily accessible with your WordPress blog. Download Windows Live Writer Download WordPress apps for your mobile device Similar Articles Productive Geek Tips Quick Tip: Set a Future Date for a Post in WordPressAdd Social Bookmarking (Digg This!) Links to your Wordpress BlogFuture Date a Post in Windows Live WriterHow To Start Your Own Professional Blog with WordPressUsing Word 2007 as a Blogging Tool TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Acronis Online Backup DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows Fun with 47 charts and graphs Tomorrow is Mother’s Day Check the Average Speed of YouTube Videos You’ve Watched OutlookStatView Scans and Displays General Usage Statistics How to Add Exceptions to the Windows Firewall Office 2010 reviewed in depth by Ed Bott

  Read the article

• Stream Music and Video Over the Internet with Windows Media Player 12

  - by DigitalGeekery

  A new feature in Windows Media Player 12, which is included with Windows 7, is being able to stream media over the web to other Windows 7 computers.  Today we will take a look at how to set it up and what you need to begin. Note: You will need to perform this process on each computer that you want to use. What You’ll Need Two computers running Windows 7 Home Premium, Professional, or Ultimate. The host, or home computer that you will be streaming the media from, cannot be on a public network or part of domain. Windows Live ID UPnP or Port Forwarding enabled on your home router Media files added to your Windows Media Player library Windows Live ID Sign up online for a Windows Live ID if you do not already have one. See the link below for a link to Windows Live.   Configuring the Windows 7 Computers Open Windows Media Player and go to the library section. Click on Stream and then “Allow Internet access to home media.”   The Internet Home Media Access pop up window will prompt you to link your Windows Live ID to a user account. Click “Link an online ID.” If you haven’t already installed the Windows Live ID Sign-In Assistant, you will be taken to Microsoft’s website and prompted to download it. Once you have completed the Windows Live download assistant install, you will see Windows Live ID online provider appear in the “Link Online IDs” window. Click on “Link Online ID.” Next, you’ll be prompted for a Windows Live ID and password. Enter your Windows Live ID and password and click “Sign In.” A pop up window will notify you that you have successfully allowed Internet access to home media. Now, you will have to repeat the exact same configuration on the 2nd Windows 7 computer. Once you have completed the same configuration on your 2nd computer, you might also need to configure your home router for port forwarding. If your router supports UPnP, you may not need to manually forward any ports on your router. So, this would be a good time to test your connection. Go to a nearby hotspot, or perhaps a neighbor’s house, and test to see if you can stream your media. If not, you’ll need to manually forward the ports. You can always choose to forward the ports anyway, just in case. Note: We tested on a Linksys WRT54GL router, which supports UPnP, and found we still needed to manually forward the ports. Finding the ports to forward on the router Open Windows Media Player and make sure you are in Library view. Click on “Stream” on the top menu, and select “Allow Internet access to home media.”   On the “Internet Home Media Access” window, click on “Diagnose connections.” The “Internet Streaming Diagnostic Tool” will pop up. Click on “Port forwarding information” near the bottom.   On the “Port Forwarding Information” window you will find both the Internal and External Port numbers you will need to forward on your router. The Internal port number should always be 10245. The external number will be different depending on your computer. Microsoft also recommends forwarding port 443. Configuring the Router Next, you’ll need to configure Port Forwarding on your home router. We will show you the steps for a Linksys WRT54GL router, however, the steps for port forwarding will vary from router to router. On the Linksys configuration page, click on the Administration Tab along the top, click the “Applications & Gaming Tab, and then the “Port Range Forward” tab below it. Under “Application,” type in a name. It can be any name you choose. In both the “Start” and “End” boxes, type the port number. Enter the IP address of your home computer in the IP address column. Click the check box under “Enable.” Do this for both the internal and external port numbers and port 443. When finished, click the “Save Settings” button. Note: It’s highly recommended that you configure your home computer with a static IP address When you’re ready to play your media over the Internet, open up Windows Media Player and look for your host computer and username listed under “Other Libraries.” Click on it expand the list to see your media libraries. Choose a library and a file to play. Now you can enjoy your streaming media over the Internet. Conclusion We found media streaming over the Internet to work fairly well. However, we did see a loss of quality with streaming video. Also, Recorded TV .wtv and dvr-ms files did not play at all. Check out our previous article to see how to stream media share and stream media between Windows 7 computers on your home network. Similar Articles Productive Geek Tips Enable Media Streaming in Windows Home Server to Windows Media PlayerFixing When Windows Media Player Library Won’t Let You Add FilesShare Digital Media With Other Computers on a Home Network with Windows 7Share and Stream Digital Media Between Windows 7 Machines On Your Home NetworkLearning Windows 7: Manage Your Music with Windows Media Player TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Stormpulse provides slick, real time weather data Geek Parents – Did you try Parental Controls in Windows 7? Change DNS servers on the fly with DNS Jumper Live PDF Searches PDF Files and Ebooks Converting Mp4 to Mp3 Easily Use Quick Translator to Translate Text in 50 Languages (Firefox)

  Read the article

• Quick guide to Oracle IRM 11g: Creating your first sealed document

  - by Simon Thorpe

  Quick guide to Oracle IRM 11g indexThe previous articles in this guide have detailed how to install, configure and secure your Oracle IRM 11g service. This article walks you through the process of now creating your first context and securing a document against it. I should mention that it would be worth reviewing the following to ensure your installation is ready for that all important first document. Ensure you have correctly configured the keystore for the IRM wrapper keys. If this is not correctly configured, creating the context below will fail. Make sure the IRM server URL correctly resolves and uses the right protocol (HTTP or HTTPS) ContentsCreate the first contextInstall the Oracle IRM Desktop Seal your first document Create the first contextIn Oracle 11g there is a built in classification and rights system called the "standard rights model" which is based on 10 years of customer use cases and innovation. It is a system which enables IRM to scale massively whilst retaining the ability to balance security and usability and also separate duties by allowing contacts in the business to own classifications. The final article in this guide goes into detail on this inbuilt classification model, but for the purposes of this current article all we need to do is create at least one context to test our system out.With a new IRM server there are a set of predefined context templates and roles which again are setup in a way which reflects the most common use we've learned from our customers. We will use these out of the box configurations as they are to create the first context against which we will seal some content.First login to your Oracle IRM Management Website located at https://irm.company.com/irm_rights/. Currently the system is only configured to use the built in LDAP for users, so use the only account we have at the moment, which by default is weblogic. Once logged in switch to the Contexts tab. Click on the New Context icon () in the menu bar on the left. In the resulting dialog select the Standard context template and enter in a name for the context. Then just hit finish, the weblogic account will automatically be made the manager. You'll now see your brand new context ready for users to be assigned. Now click on the Assign Role icon () in the menu bar and in the resulting dialog search for your only user account, weblogic, and add to the list on the right. Now select a role for this user. Because we need to create a document with this user we must select contributor, as this is the only role which allows for the ability to seal. Finally hit next and then finish. We now have a context with a user that has the rights to create a document. The next step is to configure the IRM Desktop to get these rights from the server. Install the Oracle IRM Desktop Before we can seal a document we need the client software installed. Oracle IRM has a very small, lightweight client called the Oracle IRM Desktop which can be freely downloaded in 27 languages from here. Double click on the installer and click on next... Next again... And finally on install... Very easy. You may get a warning about closing Outlook, Word or another application and most of the time no reboots are required. Once it is installed you will see the IRM Desktop icon running in your tool tray, bottom right of the desktop. Seal your first document Finally the prize is within reach, creating your first sealed document. The server is running, we've got a context ready, a user assigned a role in the context but there is the simple and obvious hoop left to jump through. To seal a document we need to have the users rights cached to the local machine. For this to take place, the IRM Desktop needs to know where the Oracle IRM server is on the network so we can synchronize these rights and then be able to seal a document. The usual way for the IRM Desktop to know about the IRM server is it learns automatically when you open an existing piece of content that someone has sent you... ack. Bit of a chicken or the egg dilemma. The solution is to manually tell the IRM Desktop the location of the IRM Server and then force a synchronization of rights. Right click on the Oracle IRM Desktop icon in the system tray and select Options.... Then switch to the Servers tab in the resulting dialog. There are no servers in the list because you've never opened any content. This list is usually populated automatically but we are going to add a server manually, so click on New.... Into the dialog enter in the full URL to the IRM server. Note that this time you use the path /irm_desktop/ and not /irm_rights/. You can see an example from the image below. Click on the validate button and you'll be asked to authenticate. Enter in your weblogic username and password and also check the Remember my password check box. Click OK and the IRM Desktop will confirm a successful connection to the server. OK all the dialogs and we are ready to Synchronize this users rights to the desktop. Right click once more on the Oracle IRM Desktop icon in the system tray. Now the Synchronize menu option is available. Select this and the IRM Desktop will now talk to the IRM server, authenticate using your weblogic account and get your rights to the context we created. Because this is the first time this users has communicated with the IRM server the IRM Desktop presents a privacy policy dialog. This is a chance for the business to ask users to agree to any policy about the use of IRM before opening secured documents. In our guide we've not bothered to setup this URL so just click on the check box and hit Accept. The IRM Desktop will then talk to the server, get your rights and display a success dialog. Lets protect a documentNow we are ready to seal a piece of content. In my guide i'm going to protect a Microsoft Word document. This mean's I have to have copy of Office installed, in this guide i'm using Microsoft Office 2007. You could also seal a PDF document, you'll need to download and install Adobe Acrobat Reader. A very simple test could be to seal a GIF/JPG/PNG or piece of HTML because this is rendered using Internet Explorer. But as I say, i'm going to protect a Word document. The following example demonstrates choosing a file in Windows Explorer, there are many ways to seal a file and you can watch a few in this video.Open a copy of Windows Explorer and locate the file you wish to seal. Right click on the document and select Seal To -> Context You are now presented with the Select Context dialog. You'll now have a sealed copy of the document sat in the same location. Double click on this document and it will open, again using the credentials you've already provided. That is it, now you just need to add more users, more documents, more classifications and start exploring the different roles and experiment with different offline periods etc. You may wish to setup the server against an existing LDAP or Active Directory environment instead of using the built in WebLogic LDAP store. You can read how to use your corporate directory here. But before we finish this guide, there is one more article and arguably the most important article of all. Next I discuss the all important decision making surrounding the actually implementation of Oracle IRM inside your business. Who has rights to what? How do you map contexts to your existing business practices? It is the next article which actually ensures you deploy a successful IRM solution by looking at the business and understanding how they use your sensitive information and then configuring Oracle IRM to reflect their use.

  Read the article

• Agile Awakenings and the Rules of Agile

  - by Robert May

  For those that care, you can read my history of management and technology to understand why I think I’m qualified to talk about this at all.  It’s boring, so feel free to skip it. Awakenings I first started to play around with the idea of “agile” in 2004 or 2005.  I found a book on the Rational Unified Process that I thought was good, and attempted to implement parts of it.  I thought I was agile, but really, it wasn’t.   I still didn’t understand the concept of a team.  I still wanted to tell the team what to do and how to get it done.  I still thought I was smarter than the team. After that job, I started work on another project and began helping that team.  The first few months were really rough.  We were implementing Scrum, which was relatively new to everyone on the team, and, quite frankly, I was doing a poor job of it.  I was trying to micro-manage every aspect of the teams work, and we were all miserable. The moment of change came when the senior architect bailed on the project.  His comment to me was: “This isn’t Agile.  Where are the stand-ups?  Where are the stories?”  He was dead on, and I finally woke up.  I finally realized that I was the problem!  I wasn’t trusting the team.  I wasn’t helping the team.  I was being a manager. Like many (most?), I was claiming to be Agile and use Scrum, but I wasn’t in fact following the rules Scrum.  Since then, I’ve done a lot of studying, hands on practice, coaching of many different teams, and other learning around Scrum, and I have discovered that Scrum has some rules that must be followed for success, even though the process is about continuous improvement. I’ve been practicing Scrum right for about 4 years now and have helped multiple teams implement it successfully, so what you’re about to get is based on experience, rather than just theory. The Rules of Scrum In my experience, what I’ve found is that most companies that claim to be doing Scrum or Agile are actually NOT doing either.  This stems largely because they think that they can “adopt the rules of Agile that fit their organization.”  Sadly, many of them think that this means they can adopt iterations (sprints) and not much else.  Either that, or they think they can do whatever they want, or were doing before, and call it Scrum.  This is simply not true. Here are some rules that must be followed for you to really be doing Scrum.  I’ll go into detail on each one of these posts in future blog posts and update links here.  My intent is that this will help other teams implementing scrum to see more success. Agile does not allow you to do whatever you want A Product Owner is required A ScrumMaster is required The team must function as a Team, and QA must be part of the team Support from upper management is required A prioritized product backlog is required A prioritized sprint backlog is required Release planning is required Complete spring planning is required Showcases are required Velocity must be measured Retrospectives are required Daily stand-ups are required Visibility is absolutely required For now, I think that’s enough, although I reserve the right to add more.  If you’re breaking any of these rules, you’re probably not doing Scrum.  There are exceptions to these rules, but until you have practiced Scrum for a while, you don’t know what those exceptions are. Breaking the Rules Many teams break these rules because they are the ones that expose the most pain.  Scrum is not Advil.  It’s not intended to mask the pain, its intended to cure it.  Let me explain that analogy a bit more.  Recently, my 7 year old son broke his arm, quite severely (see the X-Ray to the right).  That caused him a great deal of pain.  We went first to one doctor, and after viewing the X-Ray, they determined that there was no way that they’d cast the arm at their location.  It was simply too bad of a break for them to deal with.  They did, however, give him some Advil for the pain and put a splint on his arm to stabilize the broken bones.  Within minutes, he was feeling much better.  Had we been stupid, we could have gone home and he’d have been just as happy as ever . . . until the pain medication wore off or one of his siblings touched the splint.  Then, all of that pain would come right back to the top.  Sure, he could make it go away by just taking more Advil and moving the splint out of the way, but that wasn’t going to fix the problem permanently. We ended up in an emergency room with a doctor who could fix his arm.  However, we were warned that the fix was going to be VERY painful, and it was.  Even with heavy sedation (Propofol), my son was in enough pain that he squirmed and wiggled trying to get his arm away from the doctor.  He had to endure this pain in order to have a functional arm. But the setting wasn’t the end.  He had to have several casts, had to have it re-broken once, since the first setting didn’t take and finally was given a clean bill of health. Agile implementation is much like this story.  Agile was developed as a result of people recognizing that the development methodologies that were currently in place simply were ineffective.  However, the fix to the broken development that’s been festering for many years is not painless.  Many people start Agile thinking that things will be wonderful.  They won’t!  Agile is about visibility, and often, it brings great pain to surface.  It causes all of the missed deadlines, the cowboy coders, the coasters, the micro-managers, the lazy, and all of the other problems that are really part of your development process now to become painfully visible to EVERYONE.  Many people don’t like this exposure.  Agile will make the pain better, but not if you remove the cast (the rules above) prematurely and start breaking the rules that expose the most pain.  The healing will take time and is not instant (like Advil).  Figuring out what the true source of pain and fixing it is very valuable to you, your team, and your company.  Remember as you’re doing this that Agile isn’t the source of the pain, it’s really just exposing it.  Find the source. My recommendation is that ALL of these rules are followed for a minimum of six months, and preferably for an entire year, before you decide to break any of these rules.  Get a few good releases under your belt.  Figure out what your velocity is and start firing as a team.  Chances are, after you see agile really in action, you won’t want to break the rules because you’ll see their value. More Reading Jean Tabaka recently published a list of 78 Things I Have Learned in 6 Years of Agile Coaching.  Highly recommended. Technorati Tags: Agile,Scrum,Rules

  Read the article

• Building services with the .NET framework Cont’d

  - by Allan Rwakatungu

  In my previous blog I wrote an introductory post on services and how you can build services using the .NET frameworks Windows Communication Foundation (WCF) In this post I will show how to develop a real world application using WCF The problem During the last meeting we realized developers in Uganda are not so cool – they don’t use twitter so may not get the latest news and updates from the technology world. We also noticed they mostly use kabiriti phones (jokes). With their kabiriti phones they are unable to access the twitter web client or alternative twitter mobile clients like tweetdeck , twirl or tweetie. However, the kabiriti phones support SMS (Yeeeeeeei). So what we going to do to make these developers cool and keep them updated is by enabling them to receive tweets via SMS. We shall also enable them to develop their own applications that can extend this functionality Analysis Thanks to services and open API’s solving our problem is going to be easy.  1. To get tweets we can use the twitter service for FREE 2. To send SMS we shall use www.clickatell.com/ as they can send SMS to any country in the world. Besides we could not find any local service that offers API's for sending SMS :(. 3. To enable developers to integrate with our application so that they can extend it and build even cooler applications we use WCF. In addittion , because connectivity might be an issue we decided to use WCF because if has a inbuilt queing features. We also choose WCF because this is a post about .NET and WCF :). The Code Accessing the tweets To consume twitters REST API we shall use the WCF REST starter kit. Like it name indicates , the REST starter kit is a set of .NET framework classes that enable developers to create and access REST style services ( like the twitter service). Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin-top:0in; mso-para-margin-right:0in; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0in; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} using System; using System.Collections.Generic; using System.Linq; using System.Text; using Microsoft.Http; using System.Net; using System.Xml.Linq;   namespace UG.Demo {     public class TwitterService     {         public IList<TwitterStatus> SomeMethodName()         {             //Connect to the twitter service (HttpClient is part of the REST startkit classes)             HttpClient cl = new HttpClient("http://api.twitter.com/1/statuses/friends_timeline.xml");             //Supply your basic authentication credentials             cl.TransportSettings.Credentials = new NetworkCredential("ourusername", "ourpassword");             //issue an http             HttpResponseMessage resp = cl.Get();             //ensure we got reponse 200             resp.EnsureStatusIsSuccessful();             //use XLinq to parse the REST XML             var statuses = from r in resp.Content.ReadAsXElement().Descendants("status")                            select new TwitterStatus                            {                                User = r.Element("user").Element("screen_name").Value,                                Status = r.Element("text").Value                            };             return statuses.ToList();         }     }     public class TwitterStatus     {         public string User { get; set; }         public string Status { get; set; }     } }  Sending SMS Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin-top:0in; mso-para-margin-right:0in; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0in; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} public class SMSService     {         public void Send(string phone, string message)         {                         HttpClient cl1 = new HttpClient();              //the clickatell XML format for sending SMS             string xml = String.Format("<clickAPI><sendMsg><api_id>3239621</api_id><user>ourusername</user><password>ourpassword</password><to>{0}</to><text>{1}</text></sendMsg></clickAPI>",phone,message);             //Post form data             HttpUrlEncodedForm form = new HttpUrlEncodedForm();             form.Add("data", xml);             System.Net.ServicePointManager.Expect100Continue = false;             string uri = @"http://api.clickatell.com/xml/xml";             HttpResponseMessage resp = cl1.Post(uri, form.CreateHttpContent());             resp.EnsureStatusIsSuccessful();         }     }

  Read the article

• Cloud MBaaS : The Next Big Thing in Enterprise Mobility

  - by shiju

  In this blog post, I will take a look at Cloud Mobile Backend as a Service (MBaaS) and how we can leverage Cloud based Mobile Backend as a Service for building enterprise mobile apps. Today, mobile apps are incredibly significant in both consumer and enterprise space and the demand for the mobile apps is unbelievably increasing in day to day business. An enterprise can’t survive in business without a proper mobility strategy. A better mobility strategy and faster delivery of your mobile apps will give you an extra mileage for your business and IT strategy. So organizations and mobile developers are looking for different strategy for meeting this demand and adopting different development strategy for their mobile apps. Some developers are adopting hybrid mobile app development platforms, for delivering their products for multiple platforms, for fast time-to-market. Others are adopting a Mobile enterprise application platform (MEAP) such as Kony for their enterprise mobile apps for fast time-to-market and better business integration. The Challenges of Enterprise Mobility The real challenge of enterprise mobile apps, is not about creating the front-end environment or developing front-end for multiple platforms. The most important thing of enterprise mobile apps is to expose your enterprise data to mobile devices where the real pain is your business data might be residing in lot of different systems including legacy systems, ERP systems etc., and these systems will be deployed with lot of security restrictions. Exposing your data from the on-premises servers, is not a easy thing for most of the business organizations. Many organizations are spending too much time for their front-end development strategy, but they are really lacking for building a strategy on their back-end for exposing the business data to mobile apps. So building a REST services layer and mobile back-end services, on the top of legacy systems and existing middleware systems, is the key part of most of the enterprise mobile apps, where multiple mobile platforms can easily consume these REST services and other mobile back-end services for building mobile apps. For some mobile apps, we can’t predict its user base, especially for products where customers can gradually increase at any time. And for today’s mobile apps, faster time-to-market is very critical so that spending too much time for mobile app’s scalability, will not be worth. The real power of Cloud is the agility and on-demand scalability, where we can scale-up and scale-down our applications very easily. It would be great if we could use the power of Cloud to mobile apps. So using Cloud for mobile apps is a natural fit, where we can use Cloud as the storage for mobile apps and hosting mechanism for mobile back-end services, where we can enjoy the full power of Cloud with greater level of on-demand scalability and operational agility. So Cloud based Mobile Backend as a Service is great choice for building enterprise mobile apps, where enterprises can enjoy the massive scalability power of their mobile apps, provided by public cloud vendors such as Microsoft Windows Azure. Mobile Backend as a Service (MBaaS) We have discussed the key challenges of enterprise mobile apps and how we can leverage Cloud for hosting mobile backend services. MBaaS is a set of cloud-based, server-side mobile services for multiple mobile platforms and HTML5 platform, which can be used as a backend for your mobile apps with the scalability power of Cloud. The information below provides the key features of a typical MBaaS platform: Cloud based storage for your application data. Automatic REST API services on the application data, for CRUD operations. Native push notification services with massive scalability power. User management services for authenticate users. User authentication via Social accounts such as Facebook, Google, Microsoft, and Twitter. Scheduler services for periodically sending data to mobile devices. Native SDKs for multiple mobile platforms such as Windows Phone and Windows Store, Android, Apple iOS, and HTML5, for easily accessing the mobile services from mobile apps, with better security.  Typically, a MBaaS platform will provide native SDKs for multiple mobile platforms so that we can easily consume the server-side mobile services. MBaaS based REST APIs can use for integrating to enterprise backend systems. We can use the same mobile services for multiple platform so hat we can reuse the application logic to multiple mobile platforms. Public cloud vendors are building the mobile services on the top of their PaaS offerings. Windows Azure Mobile Services is a great platform for a MBaaS offering that is leveraging Windows Azure Cloud platform’s PaaS capabilities. Hybrid mobile development platform Titanium provides their own MBaaS services. LoopBack is a new MBaaS service provided by Node.js consulting firm StrongLoop, which can be hosted on multiple cloud platforms and also for on-premises servers. The Challenges of MBaaS Solutions If you are building your mobile apps with a new data storage, it will be very easy, since there is not any integration challenges you have to face. But most of the use cases, you have to extract your application data in which stored in on-premises servers which might be under VPNs and firewalls. So exposing these data to your MBaaS solution with a proper security would be a big challenge. The capability of your MBaaS vendor is very important as you have to interact with your legacy systems for many enterprise mobile apps. So you should be very careful about choosing for MBaaS vendor. At the same time, you should have a proper strategy for mobilizing your application data which stored in on-premises legacy systems, where your solution architecture and strategy is more important than platforms and tools.  Windows Azure Mobile Services Windows Azure Mobile Services is an MBaaS offerings from Windows Azure cloud platform. IMHO, Microsoft Windows Azure is the best PaaS platform in the Cloud space. Windows Azure Mobile Services extends the PaaS capabilities of Windows Azure, to mobile devices, which can be used as a cloud backend for your mobile apps, which will provide global availability and reach for your mobile apps. Windows Azure Mobile Services provides storage services, user management with social network integration, push notification services and scheduler services and provides native SDKs for all major mobile platforms and HTML5. In Windows Azure Mobile Services, you can write server-side scripts in Node.js where you can enjoy the full power of Node.js including the use of NPM modules for your server-side scripts. In the previous section, we had discussed some challenges of MBaaS solutions. You can leverage Windows Azure Cloud platform for solving many challenges regarding with enterprise mobility. The entire Windows Azure platform can play a key role for working as the backend for your mobile apps where you can leverage the entire Windows Azure platform for your mobile apps. With Windows Azure, you can easily connect to your on-premises systems which is a key thing for mobile backend solutions. Another key point is that Windows Azure provides better integration with services like Active Directory, which makes Windows Azure as the de facto platform for enterprise mobility, for enterprises, who have been leveraging Microsoft ecosystem for their application and IT infrastructure. Windows Azure Mobile Services  is going to next evolution where you can expect some exciting features in near future. One area, where Windows Azure Mobile Services should definitely need an improvement, is about the default storage mechanism in which currently it is depends on SQL Server. IMHO, developers should be able to choose multiple default storage option when creating a new mobile service instance. Let’s say, there should be a different storage providers such as SQL Server storage provider and Table storage provider where developers should be able to choose their choice of storage provider when creating a new mobile services project. I have been used Windows Azure and Windows Azure Mobile Services as the backend for production apps for mobile, where it performed very well. MBaaS Over MEAP Recently, many larger enterprises has been adopted Mobile enterprise application platform (MEAP) for their mobile apps. I haven’t worked on any production MEAP solution, but I heard that developers are really struggling with MEAP in different way. The learning curve for a proprietary MEAP platform is very high. I am completely against for using larger proprietary ecosystem for mobile apps. For enterprise mobile apps, I highly recommend to use native iOS/Android/Windows Phone or HTML5  for front-end with a cloud hosted MBaaS solution as the middleware. A MBaaS service can be consumed from multiple mobile apps where REST APIs are using to integrating with enterprise backend systems. Enterprise mobility should start with exposing REST APIs on the enterprise backend systems and these REST APIs can host on Cloud where we can enjoy the power of Cloud for our services. If you are having REST APIs for your enterprise data, then you can easily build mobile frontends for multiple platforms.   You can follow me on Twitter @shijucv

  Read the article

• SSH new connection begins to hang (not reject or terminate) after a day or so on Ubuntu 13.04 server

  - by kross

  Recently we upgraded the server from 12.04 LTS server to 13.04. All was well, including after a reboot. With all packages updated we began to see a strange issue, ssh works for a day or so (unclear on timing) then a later request for SSH hangs (cannot ctrl+c, nothing). It is up and serving webserver traffic etc. Port 22 is open (ips etc altered slightly for posting): nmap -T4 -A x.acme.com Starting Nmap 6.40 ( http://nmap.org ) at 2013-09-12 16:01 CDT Nmap scan report for x.acme.com (69.137.56.18) Host is up (0.026s latency). rDNS record for 69.137.56.18: c-69-137-56-18.hsd1.tn.provider.net Not shown: 998 filtered ports PORT STATE SERVICE VERSION 22/tcp open ssh OpenSSH 6.1p1 Debian 4 (protocol 2.0) | ssh-hostkey: 1024 54:d3:e3:38:44:f4:20:a4:e7:42:49:d0:a7:f1:3e:21 (DSA) | 2048 dc:21:77:3b:f4:4e:74:d0:87:33:14:40:04:68:33:a6 (RSA) |_256 45:69:10:79:5a:9f:0b:f0:66:15:39:87:b9:a1:37:f7 (ECDSA) 80/tcp open http Jetty 7.6.2.v20120308 | http-title: Log in as a Bamboo user - Atlassian Bamboo |_Requested resource was http://x.acme.com/userlogin!default.action;jsessionid=19v135zn8cl1tgso28fse4d50?os_destination=%2Fstart.action Service Info: OS: Linux; CPE: cpe:/o:linux:linux_kernel Service detection performed. Please report any incorrect results at http://nmap.org/submit/ . Nmap done: 1 IP address (1 host up) scanned in 12.89 seconds Here is the ssh -vvv: ssh -vvv x.acme.com OpenSSH_5.9p1, OpenSSL 0.9.8x 10 May 2012 debug1: Reading configuration data /Users/tfergeson/.ssh/config debug1: Reading configuration data /etc/ssh_config debug1: /etc/ssh_config line 20: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to x.acme.com [69.137.56.18] port 22. debug1: Connection established. debug3: Incorrect RSA1 identifier debug3: Could not load "/Users/tfergeson/.ssh/id_rsa" as a RSA1 public key debug1: identity file /Users/tfergeson/.ssh/id_rsa type 1 debug1: identity file /Users/tfergeson/.ssh/id_rsa-cert type -1 debug1: identity file /Users/tfergeson/.ssh/id_dsa type -1 debug1: identity file /Users/tfergeson/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_6.1p1 Debian-4 debug1: match: OpenSSH_6.1p1 Debian-4 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.9 debug2: fd 3 setting O_NONBLOCK debug3: load_hostkeys: loading entries for host "x.acme.com" from file "/Users/tfergeson/.ssh/known_hosts" debug3: load_hostkeys: found key type RSA in file /Users/tfergeson/.ssh/known_hosts:10 debug3: load_hostkeys: loaded 1 keys debug3: order_hostkeyalgs: prefer hostkeyalgs: [email protected],[email protected],ssh-rsa debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: [email protected],[email protected],ssh-rsa,[email protected],[email protected],ssh-dss debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-sha2-256,hmac-sha2-256-96,hmac-sha2-512,hmac-sha2-512-96,hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-sha2-256,hmac-sha2-256-96,hmac-sha2-512,hmac-sha2-512-96,hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: kex_parse_kexinit: ecdh-sha2-nistp256,ecdh-sha2-nistp384,ecdh-sha2-nistp521,diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: ssh-rsa,ssh-dss,ecdsa-sha2-nistp256 debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-sha2-256,hmac-sha2-512,hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-sha2-256,hmac-sha2-512,hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: mac_setup: found hmac-md5 debug1: kex: server->client aes128-ctr hmac-md5 none debug2: mac_setup: found hmac-md5 debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug2: dh_gen_key: priv key bits set: 130/256 debug2: bits set: 503/1024 debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA dc:21:77:3b:f4:4e:74:d0:87:33:14:40:04:68:33:a6 debug3: load_hostkeys: loading entries for host "x.acme.com" from file "/Users/tfergeson/.ssh/known_hosts" debug3: load_hostkeys: found key type RSA in file /Users/tfergeson/.ssh/known_hosts:10 debug3: load_hostkeys: loaded 1 keys debug3: load_hostkeys: loading entries for host "69.137.56.18" from file "/Users/tfergeson/.ssh/known_hosts" debug3: load_hostkeys: found key type RSA in file /Users/tfergeson/.ssh/known_hosts:6 debug3: load_hostkeys: loaded 1 keys debug1: Host 'x.acme.com' is known and matches the RSA host key. debug1: Found key in /Users/tfergeson/.ssh/known_hosts:10 debug2: bits set: 493/1024 debug1: ssh_rsa_verify: signature correct debug2: kex_derive_keys debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /Users/tfergeson/.ssh/id_rsa (0x7ff189c1d7d0) debug2: key: /Users/tfergeson/.ssh/id_dsa (0x0) debug1: Authentications that can continue: publickey debug3: start over, passed a different list publickey debug3: preferred publickey,keyboard-interactive,password debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive,password debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Offering RSA public key: /Users/tfergeson/.ssh/id_rsa debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug1: Server accepts key: pkalg ssh-rsa blen 277 debug2: input_userauth_pk_ok: fp 3c:e5:29:6c:9d:27:d1:7d:e8:09:a2:e8:8e:6e:af:6f debug3: sign_and_send_pubkey: RSA 3c:e5:29:6c:9d:27:d1:7d:e8:09:a2:e8:8e:6e:af:6f debug1: read PEM private key done: type RSA debug1: Authentication succeeded (publickey). Authenticated to x.acme.com ([69.137.56.18]:22). debug1: channel 0: new [client-session] debug3: ssh_session2_open: channel_new: 0 debug2: channel 0: send open debug1: Requesting [email protected] debug1: Entering interactive session. debug2: callback start debug2: client_session2_setup: id 0 debug2: fd 3 setting TCP_NODELAY debug2: channel 0: request pty-req confirm 1 debug1: Sending environment. debug3: Ignored env ATLAS_OPTS debug3: Ignored env rvm_bin_path debug3: Ignored env TERM_PROGRAM debug3: Ignored env GEM_HOME debug3: Ignored env SHELL debug3: Ignored env TERM debug3: Ignored env CLICOLOR debug3: Ignored env IRBRC debug3: Ignored env TMPDIR debug3: Ignored env Apple_PubSub_Socket_Render debug3: Ignored env TERM_PROGRAM_VERSION debug3: Ignored env MY_RUBY_HOME debug3: Ignored env TERM_SESSION_ID debug3: Ignored env USER debug3: Ignored env COMMAND_MODE debug3: Ignored env rvm_path debug3: Ignored env COM_GOOGLE_CHROME_FRAMEWORK_SERVICE_PROCESS/USERS/tfergeson/LIBRARY/APPLICATION_SUPPORT/GOOGLE/CHROME_SOCKET debug3: Ignored env JPDA_ADDRESS debug3: Ignored env APDK_HOME debug3: Ignored env SSH_AUTH_SOCK debug3: Ignored env Apple_Ubiquity_Message debug3: Ignored env __CF_USER_TEXT_ENCODING debug3: Ignored env rvm_sticky_flag debug3: Ignored env MAVEN_OPTS debug3: Ignored env LSCOLORS debug3: Ignored env rvm_prefix debug3: Ignored env PATH debug3: Ignored env PWD debug3: Ignored env JAVA_HOME debug1: Sending env LANG = en_US.UTF-8 debug2: channel 0: request env confirm 0 debug3: Ignored env JPDA_TRANSPORT debug3: Ignored env rvm_version debug3: Ignored env M2_HOME debug3: Ignored env HOME debug3: Ignored env SHLVL debug3: Ignored env rvm_ruby_string debug3: Ignored env LOGNAME debug3: Ignored env M2_REPO debug3: Ignored env GEM_PATH debug3: Ignored env AWS_RDS_HOME debug3: Ignored env rvm_delete_flag debug3: Ignored env EC2_PRIVATE_KEY debug3: Ignored env RUBY_VERSION debug3: Ignored env SECURITYSESSIONID debug3: Ignored env EC2_CERT debug3: Ignored env _ debug2: channel 0: request shell confirm 1 debug2: callback done debug2: channel 0: open confirm rwindow 0 rmax 32768 I can hard reboot (only mac monitors at that location) and it will again be accessible. This now happens every single time. It is imperative that I get it sorted. The strange thing is that it behaves initially then starts to hang after several hours. I perused logs previously and nothing stood out. From the auth.log, I can see that it has allowed me in, but still I get nothing back on the client side: Sep 20 12:47:50 cbear sshd[25376]: Accepted publickey for tfergeson from 10.1.10.14 port 54631 ssh2 Sep 20 12:47:50 cbear sshd[25376]: pam_unix(sshd:session): session opened for user tfergeson by (uid=0) UPDATES: Still occurring even after setting UseDNS no and commenting out #session optional pam_mail.so standard noenv This does not appear to be a network/dns related issue, as all services running on the machine are as responsive and accessible as ever, with the exception of sshd. Any thoughts on where to start?

  Read the article

• Monitor your Hard Drive’s Health with Acronis Drive Monitor

  - by Matthew Guay

  Are you worried that your computer’s hard drive could die without any warning?  Here’s how you can keep tabs on it and get the first warning signs of potential problems before you actually lose your critical data. Hard drive failures are one of the most common ways people lose important data from their computers.  As more of our memories and important documents are stored digitally, a hard drive failure can mean the loss of years of work.  Acronis Drive Monitor helps you avert these disasters by warning you at the first signs your hard drive may be having trouble.  It monitors many indicators, including heat, read/write errors, total lifespan, and more. It then notifies you via a taskbar popup or email that problems have been detected.  This early warning lets you know ahead of time that you may need to purchase a new hard drive and migrate your data before it’s too late. Getting Started Head over to the Acronis site to download Drive Monitor (link below).  You’ll need to enter your name and email, and then you can download this free tool. Also, note that the download page may ask if you want to include a trial of their for-pay backup program.  If you wish to simply install the Drive Monitor utility, click Continue without adding. Run the installer when the download is finished.  Follow the prompts and install as normal. Once it’s installed, you can quickly get an overview of your hard drives’ health.  Note that it shows 3 categories: Disk problems, Acronis backup, and Critical Events.  On our computer, we had Seagate DiskWizard, an image backup utility based on Acronis Backup, installed, and Acronis detected it. Drive Monitor stays running in your tray even when the application window is closed.  It will keep monitoring your hard drives, and will alert you if there’s a problem. Find Detailed Information About Your Hard Drives Acronis’ simple interface lets you quickly see an overview of how the drives on your computer are performing.  If you’d like more information, click the link under the description.  Here we see that one of our drives have overheated, so click Show disks to get more information. Now you can select each of your drives and see more information about them.  From the Disk overview tab that opens by default, we see that our drive is being monitored, has been running for a total of 368 days, and that it’s health is good.  However, it is running at 113F, which is over the recommended max of 107F.   The S.M.A.R.T. parameters tab gives us more detailed information about our drive.  Most users wouldn’t know what an accepted value would be, so it also shows the status.  If the value is within the accepted parameters, it will report OK; otherwise, it will show that has a problem in this area. One very interesting piece of information we can see is the total number of Power-On Hours, Start/Stop Count, and Power Cycle Count.  These could be useful indicators to check if you’re considering purchasing a second hand computer.  Simply load this program, and you’ll get a better view of how long it’s been in use. Finally, the Events tab shows each time the program gave a warning.  We can see that our drive, which had been acting flaky already, is routinely overheating even when our other hard drive was running in normal temperature ranges. Monitor Acronis Backups And Critical Errors In addition to monitoring critical stats of your hard drives, Acronis Drive Monitor also keeps up with the status of your backup software and critical events reported by Windows.  You can access these from the front page, or via the links on the left hand sidebar.  If you have any edition of any Acronis Backup product installed, it will show that it was detected.  Note that it can only monitor the backup status of the newest versions of Acronis Backup and True Image. If no Acronis backup software was installed, it will show a warning that the drive may be unprotected and will give you a link to download Acronis backup software.   If you have another backup utility installed that you wish to monitor yourself, click Configure backup monitoring, and then disable monitoring on the drives you’re monitoring yourself. Finally, you can view any detected Critical events from the Critical events tab on the left. Get Emailed When There’s a Problem One of Drive Monitor’s best features is the ability to send you an email whenever there’s a problem.  Since this program can run on any version of Windows, including the Server and Home Server editions, you can use this feature to stay on top of your hard drives’ health even when you’re not nearby.  To set this up, click Options in the top left corner. Select Alerts on the left, and then click the Change settings link to setup your email account. Enter the email address which you wish to receive alerts, and a name for the program.  Then, enter the outgoing mail server settings for your email.  If you have a Gmail account, enter the following information: Outgoing mail server (SMTP): smtp.gmail.com Port: 587 Username and Password: Your gmail address and password Check the Use encryption box, and then select TLS from the encryption options.   It will now send a test message to your email account, so check and make sure it sent ok. Now you can choose to have the program automatically email you when warnings and critical alerts appear, and also to have it send regular disk status reports.   Conclusion Whether you’ve got a brand new hard drive or one that’s seen better days, knowing the real health of your it is one of the best ways to be prepared before disaster strikes.  It’s no substitute for regular backups, but can help you avert problems.  Acronis Drive Monitor is a nice tool for this, and although we wish it wasn’t so centered around their backup offerings, we still found it a nice tool. Link Download Acronis Drive Monitor (registration required) Similar Articles Productive Geek Tips Quick Tip: Change Monitor Timeout From Command LineAnalyze and Manage Hard Drive Space with WinDirStatMonitor CPU, Memory, and Disk IO In Windows 7 with Taskbar MetersDefrag Multiple Hard Drives At Once In WindowsFind Your Missing USB Drive on Windows XP TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips HippoRemote Pro 2.2 Xobni Plus for Outlook All My Movies 5.9 CloudBerry Online Backup 1.5 for Windows Home Server Windows 7’s WordPad is Actually Good Greate Image Viewing and Management with Zoner Photo Studio Free Windows Media Player Plus! – Cool WMP Enhancer Get Your Team’s World Cup Schedule In Google Calendar Backup Drivers With Driver Magician TubeSort: YouTube Playlist Organizer

  Read the article

• Using a "white list" for extracting terms for Text Mining

  - by [email protected]

  In Part 1 of my post on "Generating cluster names from a document clustering model" (part 1, part 2, part 3), I showed how to build a clustering model from text documents using Oracle Data Miner, which automates preparing data for text mining. In this process we specified a custom stoplist and lexer and relied on Oracle Text to identify important terms.  However, there is an alternative approach, the white list, which uses a thesaurus object with the Oracle Text CTXRULE index to allow you to specify the important terms. INTRODUCTIONA stoplist is used to exclude, i.e., black list, specific words in your documents from being indexed. For example, words like a, if, and, or, and but normally add no value when text mining. Other words can also be excluded if they do not help to differentiate documents, e.g., the word Oracle is ubiquitous in the Oracle product literature. One problem with stoplists is determining which words to specify. This usually requires inspecting the terms that are extracted, manually identifying which ones you don't want, and then re-indexing the documents to determine if you missed any. Since a corpus of documents could contain thousands of words, this could be a tedious exercise. Moreover, since every word is considered as an individual token, a term excluded in one context may be needed to help identify a term in another context. For example, in our Oracle product literature example, the words "Oracle Data Mining" taken individually are not particular helpful. The term "Oracle" may be found in nearly all documents, as with the term "Data." The term "Mining" is more unique, but could also refer to the Mining industry. If we exclude "Oracle" and "Data" by specifying them in the stoplist, we lose valuable information. But it we include them, they may introduce too much noise. Still, when you have a broad vocabulary or don't have a list of specific terms of interest, you rely on the text engine to identify important terms, often by computing the term frequency - inverse document frequency metric. (This is effectively a weight associated with each term indicating its relative importance in a document within a collection of documents. We'll revisit this later.) The results using this technique is often quite valuable. As noted above, an alternative to the subtractive nature of the stoplist is to specify a white list, or a list of terms--perhaps multi-word--that we want to extract and use for data mining. The obvious downside to this approach is the need to specify the set of terms of interest. However, this may not be as daunting a task as it seems. For example, in a given domain (Oracle product literature), there is often a recognized glossary, or a list of keywords and phrases (Oracle product names, industry names, product categories, etc.). Being able to identify multi-word terms, e.g., "Oracle Data Mining" or "Customer Relationship Management" as a single token can greatly increase the quality of the data mining results. The remainder of this post and subsequent posts will focus on how to produce a dataset that contains white list terms, suitable for mining. CREATING A WHITE LIST We'll leverage the thesaurus capability of Oracle Text. Using a thesaurus, we create a set of rules that are in effect our mapping from single and multi-word terms to the tokens used to represent those terms. For example, "Oracle Data Mining" becomes "ORACLEDATAMINING." First, we'll create and populate a mapping table called my_term_token_map. All text has been converted to upper case and values in the TERM column are intended to be mapped to the token in the TOKEN column. TERM                                TOKEN DATA MINING                         DATAMINING ORACLE DATA MINING                  ORACLEDATAMINING 11G                                 ORACLE11G JAVA                                JAVA CRM                                 CRM CUSTOMER RELATIONSHIP MANAGEMENT    CRM ... Next, we'll create a thesaurus object my_thesaurus and a rules table my_thesaurus_rules: CTX_THES.CREATE_THESAURUS('my_thesaurus', FALSE); CREATE TABLE my_thesaurus_rules (main_term     VARCHAR2(100),                                  query_string  VARCHAR2(400)); We next populate the thesaurus object and rules table using the term token map. A cursor is defined over my_term_token_map. As we iterate over  the rows, we insert a synonym relationship 'SYN' into the thesaurus. We also insert into the table my_thesaurus_rules the main term, and the corresponding query string, which specifies synonyms for the token in the thesaurus. DECLARE   cursor c2 is     select token, term     from my_term_token_map; BEGIN   for r_c2 in c2 loop     CTX_THES.CREATE_RELATION('my_thesaurus',r_c2.token,'SYN',r_c2.term);     EXECUTE IMMEDIATE 'insert into my_thesaurus_rules values                        (:1,''SYN(' || r_c2.token || ', my_thesaurus)'')'     using r_c2.token;   end loop; END; We are effectively inserting the token to return and the corresponding query that will look up synonyms in our thesaurus into the my_thesaurus_rules table, for example:     'ORACLEDATAMINING'        SYN ('ORACLEDATAMINING', my_thesaurus)At this point, we create a CTXRULE index on the my_thesaurus_rules table: create index my_thesaurus_rules_idx on        my_thesaurus_rules(query_string)        indextype is ctxsys.ctxrule; In my next post, this index will be used to extract the tokens that match each of the rules specified. We'll then compute the tf-idf weights for each of the terms and create a nested table suitable for mining.

  Read the article

• Migrating SQL Server Databases – The DBA’s Checklist (Part 1)

  - by Sadequl Hussain

  It is a fact of life: SQL Server databases change homes. They move from one instance to another, from one version to the next, from old servers to new ones.  They move around as an organisation’s data grows, applications are enhanced or new versions of the database software are released. If not anything else, servers become old and unreliable and databases eventually need to find a new home. Consider the following scenarios: 1.     A new  database application is rolled out in a production server from the development or test environment 2.     A copy of the production database needs to be installed in a test server for troubleshooting purposes 3.     A copy of the development database is regularly refreshed in a test server during the system development life cycle 4.     A SQL Server is upgraded to a newer version. This can be an in-place upgrade or a side-by-side migration 5.     One or more databases need to be moved between different instances as part of a consolidation strategy. The instances can be running the same or different version of SQL Server 6.     A database has to be restored from a backup file provided by a third party application vendor 7.     A backup of the database is restored in the same or different instance for disaster recovery 8.     A database needs to be migrated within the same instance: a.     Files are moved from direct attached storage to storage area network b.    The same database is copied under a different name for another application Migrating SQL Server database applications is a complex topic in itself. There are a number of components that can be involved: jobs, DTS or SSIS packages, logins or linked servers are only few pieces of the puzzle. However, in this article we will focus only on the central part of migration: the installation of the database itself. Unless it is an in-place upgrade, typically the database is taken from a source server and installed in a destination instance.  Most of the time, a full backup file is used for the rollout. The backup file is either provided to the DBA or the DBA takes the backup and restores it in the target server. Sometimes the database is detached from the source and the files are copied to and attached in the destination. Regardless of the method of copying, moving, refreshing, restoring or upgrading the physical database, there are a number of steps the DBA should follow before and after it has been installed in the destination. It is these post database installation steps we are going to discuss below. Some of these steps apply in almost every scenario described above while some will depend on the type of objects contained within the database.  Also, the principles hold regardless of the number of databases involved. Step 1:  Make a copy of data and log files when attaching and detaching When detaching and attaching databases, ensure you have made copies of the data and log files if the destination is running a newer version of SQL Server. This is because once attached to a newer version, the database cannot be detached and attached back to an older version. Trying to do so will give you a message like the following: Server: Msg 602, Level 21, State 50, Line 1 Could not find row in sysindexes for database ID 6, object ID 1, index ID 1. Run DBCC CHECKTABLE on sysindexes. Connection Broken If you try to backup the attached database and restore it in the source, it will still fail. Similarly, if you are restoring the database in a newer version, it cannot be backed up or detached and put back in an older version of SQL. Unlike detach and attach method though, you do not lose the backup file or the original database here. When detaching and attaching a database, it is important you keep all the log files available along with the data files. It is possible to attach a database without a log file and SQL Server can be instructed to create a new log file, however this does not work if the database was detached when the primary file group was read-only. You will need all the log files in such cases. Step 2: Change database compatibility level Once the database has been restored or attached to a newer version of SQL Server, change the database compatibility level to reflect the newer version unless there is a compelling reason not to do so. When attaching or restoring from a previous version of SQL, the database retains the older version’s compatibility level.  The only time you would want to keep a database with an older compatibility level is when the code within your database is no longer supported by SQL Server. For example, outer joins with *= or the =* operators were still possible in SQL 2000 (with a warning message), but not in SQL 2005 anymore. If your stored procedures or triggers are using this form of join, you would want to keep the database with an older compatibility level.  For a list of compatibility issues between older and newer versions of SQL Server databases, refer to the Books Online under the sp_dbcmptlevel topic. Application developers and architects can help you in deciding whether you should change the compatibility level or not. You can always change the compatibility mode from the newest to an older version if necessary. To change the compatibility level, you can either use the database’s property from the SQL Server Management Studio or use the sp_dbcmptlevel stored procedure.   Bear in mind that you cannot run the built-in reports for databases from SQL Server Management Studio if you keep the database with an older compatibility level. The following figure shows the error message I received when trying to run the “Disk Usage by Top Tables” report against a database. This database was hosted in a SQL Server 2005 system and still had a compatibility mode 80 (SQL 2000).     Continues…

  Read the article

• CodePlex Daily Summary for Sunday, May 30, 2010

  CodePlex Daily Summary for Sunday, May 30, 2010New ProjectsAviva Solutions C# Coding Guidelines: A set of C# coding guidelines, coding standards, layout rules, FxCop rulesets and (upcoming) custom FxCop and StyleCop rules for improving the over...BKWork: private project.classbook: du an trong vong 10 ngay. Nhom (Do Bao Linh, Phan Thanh Tai, Nguyen Dang Loc)Du an - 01: Du an mon thay LuongEndNote助手: EndNote Helper is a assistant tool for EndNote, which make your task of reference management more convinent. EndNote 助手是一个用于辅助EndNote进行文献管理的小工具，它可...Evoucher: Simple Evoucher Sales SystemFiddler Delayed Responses Extension: A fiddler extension that help developers delay the delivery of HTML Responses to applications. Some delay user stories: - Delivery of css to HTML ...Generic Entity Model 2: GEM2 is lightweight entity framework for building custom business solutions. It enables rapid approach to entity logic design, while offering out o...GY06: 这个是长大工院于2009年发起的项目，因为种种原因没有完成。JoshDOS: JoshDOS is a command line operating system kernel based off COSMOS. It can be booted from actual hardware and built in Visual Studio using .NET la...PhysicsFMUDeluxe.NET: Este projeto é desenvolvido com o intuíto de treinar o desenvolvimento de aplicações em C#. Ele contém ferramentas para cálculos de física e matemá...Reactor Services Platform: Reactor is a service composition and deployment grid that streamlines developing, composing, deploying and managing services. Reactor Services are ...SerafinApartment: Simple MVC 2 application for apartment rental. It is multingual booking system, that allows users to register, book and subscribe for notifications...Silverlight Audio Effect Box: This is a C# Silverlight 4 sample application which process audio sample in near real time. It allows to capture the default audio input device and...Smart Voice: Smart Voice let's you control Skype using your voice. It allows you to write messages, issue phone calls, etc. This application was developed think...WebDotNet - The minimalist web framework inspired by web.py: WebDotNet is an experiment in web frameworks. Inspired by the python web framework, web.py, it is an exercise in extreme minimalism in a framework...New ReleasesAcies: Acies - Alpha Build 0.0.7: Alpha release. Requires Microsoft XNA Framework Redistributable 3.1 (http://www.microsoft.com/downloads/details.aspx?FamilyID=53867a2a-e249-4560-...AdventureWorksLT 2008 Sample Database Script: AdventureWorksLT 2008 R2 DB Script: This script is based on latest download from the Sample database for SQL Server 2008 R2. The original download from the sample is approx 84 MB and ...ASP.NET Wiki Control: Release 1.3.1: - Removed ASP.NET Session dependency. BreadCrumbs will now work with sessions disabled. Can now also share a URL and have the breadcrumb appropriat...Aviva Solutions C# Coding Guidelines: Visual Studio 2010 Rule Sets: Rule Sets targetting different styles of projects.bvcms - Bellevue Church Management System: Source: This source was used to build the latest {church}.bvcms.comCC.Yacht: CC.Yacht 1.0.10.529: This is the initial release of CC.Yacht. Marked as beta since I don't have any testing/feedback beyond that of myself and my wife.Community Forums NNTP bridge: Community Forums NNTP Bridge V14: Release of the Community Forums NNTP Bridge to access the social and anwsers MS forums with a single, open source NNTP bridge. This release has add...Community Forums NNTP bridge: Community Forums NNTP Bridge V15: Release of the Community Forums NNTP Bridge to access the social and anwsers MS forums with a single, open source NNTP bridge. This release has add...Coronasoft Cryostasis scripting engine: CCSE v0.0.1.0 BETA: This is the 0.0.1.0 Beta Release. If you find any bugs Post them as a comment or in the Discussions tabEndNote助手: EndNote助手2.1.0..0: 去除了注册验证机制。Fiddler Delayed Responses Extension: v0.1: Version 0.1 of Fiddler Delayed Responses Extension. See ChangeLog for more information.Generic Entity Model 2: GEM2 build 52510: This is first BETA release of GEM2! Following implementation is still missing from initial plan: Detailed documentation MySQL operational databa...JoshDOS: JoshDOS Souce: This is the souce for the JoshDOS 1.0 OS kernel. You need the COSMOS user kit to use.JoshDOS: Shell Version 1.0: Whats in this download *JoshDOS user kit *JoshDOS VStudio starter kit *JoshDOS documentation Note: You will need the COSMOS user kit to start deve...miniTodo: mini Todo version 0.3: Todo完了時に音が出なかったのを修正Model Virtual Casting - ASPItalia.com: Model Virtual Casting 0.2: Model Virtual Casting 0.2Questa seconda release di ModelVC è corrispondente a quella mostrata in occasione della Real Code Conference 4.0 tenutasi ...PhysicsFMUDeluxe.NET: PhysicsFMUDeluxe.NET - Setup: Primeira versão pública do PhysicsFMUDeluxe.NETSilverlight Audio Effect Box: Echo Box 1.0: First realease - zip contains : web page + xap file :Smart Voice: Smart Voice 0.1: Here is the first alpha release of Smart Voice. Please remember this was done for a curricular unit project at my university and i understand that ...StyleCop Contrib: Custom rules v0.2: This release of the custom rules target StyleCop 4.3.3. Included rules are: Spacing Rules - NoTrailingWhiteSpace - IndentUsingTabs Ordering Rules ...System.ComponentModel.DataAnnotations Contrib: 0.2.46280.0: Built with Visual Studio 2010/.Net 4.0. Compiled from source code changeset 46280.VB Styler: VB Styler Suite V 1.3.0.0: This is the newest version of the VB Styler. Here are the new features. New Imaging ColorPicker A template for getting colors via sliders ColorR...VCC: Latest build, v2.1.30529.0: Automatic drop of latest buildWPF Application Framework (WAF): WPF Application Framework (WAF) 1.0.0.90 RC: Version: 1.0.0.90 (Release Candidate): This release contains the source code of the WPF Application Framework (WAF) and the sample applications. ...XNA Collision Detection: XNA Collision Detection Sample Program: I have coded a compact program which shows the collision detection working, and provides a camera class for rendering and moving the "player." Agai...Most Popular ProjectsRawrWBFS ManagerAJAX Control ToolkitMicrosoft SQL Server Product Samples: DatabaseSilverlight ToolkitWindows Presentation Foundation (WPF)patterns & practices – Enterprise LibraryMicrosoft SQL Server Community & SamplesPHPExcelASP.NETMost Active ProjectsAStar.netpatterns & practices – Enterprise LibraryCommunity Forums NNTP bridgeBlogEngine.NETGMap.NET - Great Maps for Windows Forms & PresentationIonics Isapi Rewrite FilterRawrCustomer Portal Accelerator for Microsoft Dynamics CRMFacebook Developer ToolkitPAP

  Read the article

• Life Technologies: Making Life Easier to Manage

  - by Michael Snow

  12.00 Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-family:"Calibri","sans-serif"; mso-bidi-font-family:"Times New Roman";} When we’re thinking about customer engagement, we’re acutely aware of all the forces at play competing for our customer’s attention. Solutions that make life easier for our customers draw attention to themselves. We tend to engage more when there is a distinct benefit and we can take a deep breath and accept that there is hope in the world and everything isn’t designed to frustrate us and make our lives miserable. (sigh…) When products are designed to automate processes that were consuming hours of our time with no relief in sight, they deserve to be recognized. One of our recent Oracle Fusion Middleware Innovation Award Winners in the WebCenter category, Life Technologies, has recently posted a video promoting their “award winning” solution. The Oracle Innovation Awards are part of the overall Oracle Excellence awards given to customers for innovation with Oracle products. More info here. Their award nomination included this description: Life Technologies delivered the My Life Service Portal as part of a larger Digital Hub strategy. This Portal is the first of its kind in the biotechnology service providing industry. The Portal provides access to Life Technologies cloud based service monitoring system where all customer deployed instruments can be remotely monitored and proactively repaired. The portal provides alerts from these cloud based monitoring services directly to the customer and to Life Technologies Field Engineers. The Portal provides insight into the instruments and services customers purchased for the purpose of analyzing and anticipating future customer needs and creating targeted sales and service programs. This portal not only provides benefits for Life Technologies internal sales and service teams but provides customers a central place to track all pertinent instrument information including: instrument service history instrument status and previous activities instrument performance analytics planned service visits warranty/contract information discussion forums social networks for lab management and collaboration alerts and notifications on all of the above team scheduling for instrument usage promote optional reagents required to keep instruments performing From their website The Life Technologies Instruments & Services Portal Helps You Save Time and Gain Peace of Mind Introducing the new, award-winning, free online tool that enables easier management of your instrument use and care, faster response to requests for service or service quotes, and instant sharing of key instrument and service information with your colleagues. Now – this unto itself is obviously beneficial for their customers who were previously burdened with having to do all of these tasks separately, manually and inconsistently by nature. Now – all in one place and free to their customers – a portal that ties it all together. They now have built the platform to give their customers yet another reason to do business with them – Their headline on their product page says it all: “Life is now easier to manage - All your instrument use and care in one place – the no-cost, no-hassle Instruments and Services Portal.” Of course – it’s very convenient that the company name includes “Life” and now can also promote to their clients and prospects that doing business with them is easy and their sophisticated lab equipment is easy to manage. In an industry full of PhD’s – “Easy” isn’t usually the first word that comes to mind, but Life Technologies has now tied the word to their brand in a very eloquent way. Between our work lives and family or personal lives, getting any mono-focused minutes of dedicated attention has become such a rare occurrence in our current era of multi-tasking that those moments of focus are highly prized. So – when something is done really well – so well that it becomes captivating and urges sharing impulses – I take notice and dig deeper and most of the time I discover other gems not so hidden below the surface. And then I share with those I know would enjoy and understand. In the spirit of full disclosure, I must admit here that the first person I shared the videos below with was my daughter. She’s in her senior year of high school in the midst of her college search. She’s passionate about her academics and has already decided that she wants to study Neuroscience in college and like her mother will be in for the long haul to a PhD eventually. In a summer science program at Smith College 2 summers ago – she sent the family famous text to me – “I just dissected a sheep’s brain – wicked cool!” – This was followed by an equally memorable text this past summer in a research mentorship in Neuroscience at UConn – “Just sliced up some rat brain. Reminded me of a deli slicer at the supermarket… sorry I forgot to call last night…” So… needless to say – I knew I had an audience that would enjoy and understand these videos below and are now being shared among her science classmates and faculty. And evidently - so does Life Technologies! They’ve done a great job on these making them fun and something that will easily be shared among their customers social networks. They’ve created a neuro-archetypal character, “Ph.Diddy” and know that their world of clients in academics, research, and other institutions would understand and enjoy the “edutainment” value in this series of videos on their YouTube channel that pokes fun at the stereotypes while also promoting their products at the same time. They use their Facebook page for additional engagement with their clients and as another venue to promote these videos. Enjoy this one as well! More to be found here: http://www.youtube.com/lifetechnologies Stay tuned to this Oracle WebCenter blog channel. Tomorrow we'll be taking a look at another winner of the Innovation Awards, LADWP - helping to keep the citizens of Los Angeles engaged with their Water and Power provider.

  Read the article

• Why won't fetchmail work all of a sudden?

  - by SirCharlo

  I ran a chmod 777 * on my home folder. (I know, I know. I'll never do it again.) Ever since then, fetchmail seems to be broken. I use it to fetch mail from an Exchange 2003 mailbox through DAVMail and OWA. The problem is that fetchmail complains about an "expunge mismatch" whenever I get a new message. It deletes the message from the Exchange mailbox, yet it never forwards it. There seems to be a problem somwhere along the mail processing, but I haven't been able to pinpoint where. Any help would be appreciated. Here are the relevant config files. ~/fetchmailrc: set no bouncemail defaults: antispam -1 batchlimit 100 poll localhost with protocol imap and port 1143 user domain\\user password Password is root no rewrite mda "/usr/bin/procmail -f %F -d %T"; ~/procmailrc: :0 * ^Subject.*ack | expand | sed -e 's/[ ]*$//g' | sed -e 's/^/ /' > /usr/local/nagios/libexec/mail_acknowledgement ~/.forward: | "/usr/bin/procmail" And here is the output when I run fetchmail -f /root/.fetchmailrc -vv: fetchmail: WARNING: Running as root is discouraged. Old UID list from localhost: <empty> Scratch list of UIDs: <empty> fetchmail: 6.3.19 querying localhost (protocol IMAP) at Tue 03 Jul 2012 09:46:36 AM EDT: poll started Trying to connect to 127.0.0.1/1143...connected. fetchmail: IMAP< * OK [CAPABILITY IMAP4REV1 AUTH=LOGIN] IMAP4rev1 DavMail 3.9.7-1870 server ready fetchmail: IMAP> A0001 CAPABILITY fetchmail: IMAP< * CAPABILITY IMAP4REV1 AUTH=LOGIN fetchmail: IMAP< A0001 OK CAPABILITY completed fetchmail: Protocol identified as IMAP4 rev 1 fetchmail: GSSAPI error gss_inquire_cred: Unspecified GSS failure. Minor code may provide more information fetchmail: GSSAPI error gss_inquire_cred: fetchmail: No suitable GSSAPI credentials found. Skipping GSSAPI authentication. fetchmail: If you want to use GSSAPI, you need credentials first, possibly from kinit. fetchmail: IMAP> A0002 LOGIN "domain\\user" * fetchmail: IMAP< A0002 OK Authenticated fetchmail: selecting or re-polling default folder fetchmail: IMAP> A0003 SELECT "INBOX" fetchmail: IMAP< * 1 EXISTS fetchmail: IMAP< * 1 RECENT fetchmail: IMAP< * OK [UIDVALIDITY 1] fetchmail: IMAP< * OK [UIDNEXT 344] fetchmail: IMAP< * FLAGS (\Answered \Deleted \Draft \Flagged \Seen $Forwarded Junk) fetchmail: IMAP< * OK [PERMANENTFLAGS (\Answered \Deleted \Draft \Flagged \Seen $Forwarded Junk)] fetchmail: IMAP< A0003 OK [READ-WRITE] SELECT completed fetchmail: 1 message waiting after first poll fetchmail: IMAP> A0004 EXPUNGE fetchmail: IMAP< A0004 OK EXPUNGE completed fetchmail: 1 message waiting after expunge fetchmail: IMAP> A0005 SEARCH UNSEEN fetchmail: IMAP< * SEARCH 1 fetchmail: 1 is unseen fetchmail: IMAP< A0005 OK SEARCH completed fetchmail: 1 is first unseen 1 message for domain\user at localhost. fetchmail: IMAP> A0006 FETCH 1 RFC822.SIZE fetchmail: IMAP< * 1 FETCH (UID 343 RFC822.SIZE 1350) fetchmail: IMAP< A0006 OK FETCH completed fetchmail: IMAP> A0007 FETCH 1 RFC822.HEADER fetchmail: IMAP< * 1 FETCH (UID 343 RFC822.HEADER {1350} reading message domain\user@localhost:1 of 1 (1350 header octets) fetchmail: about to deliver with: /usr/bin/procmail -f '[email protected]' -d 'root' # fetchmail: IMAP< fetchmail: IMAP< fetchmail: IMAP< Bonne journ=E9e.. fetchmail: IMAP< fetchmail: IMAP< Company Name fetchmail: IMAP< My Name fetchmail: IMAP< IT fetchmail: IMAP< Tel: (XXX) XXX-XXXX xXXX fetchmail: IMAP< www.domain.com=20 fetchmail: IMAP< fetchmail: IMAP< fetchmail: IMAP< -----Message d'origine----- fetchmail: IMAP< De=A0: User [mailto:[email protected]]=20 fetchmail: IMAP< Envoy=E9=A0: 2 juillet 2012 15:50 fetchmail: IMAP< =C0=A0: Informatique fetchmail: IMAP< Objet=A0: PROBLEM: photo fetchmail: IMAP< fetchmail: IMAP< Notification Type: PROBLEM fetchmail: IMAP< Author:=20 fetchmail: IMAP< Comment:=20 fetchmail: IMAP< fetchmail: IMAP< Host: Photos fetchmail: IMAP< Hostname: photo fetchmail: IMAP< State: DOWN fetchmail: IMAP< Address: XXX.XX.X.XX fetchmail: IMAP< fetchmail: IMAP< Date/Time: Mon Jul 2 15:49:38 EDT 2012 fetchmail: IMAP< fetchmail: IMAP< Info: CRITICAL - XXX.XX.X.XX: rta nan, lost 100% fetchmail: IMAP< fetchmail: IMAP< fetchmail: IMAP< ) fetchmail: IMAP< A0007 OK FETCH completed fetchmail: IMAP> A0008 FETCH 1 BODY.PEEK[TEXT] fetchmail: IMAP< * 1 FETCH (UID 343 BODY[TEXT] {539} (539 body octets) ******************************* fetchmail: IMAP< ) fetchmail: IMAP< A0008 OK FETCH completed flushed fetchmail: IMAP> A0009 STORE 1 +FLAGS (\Seen \Deleted) fetchmail: IMAP< * 1 FETCH (UID 343 FLAGS (\Seen \Deleted)) fetchmail: IMAP< * 1 EXPUNGE fetchmail: IMAP< A0009 OK STORE completed fetchmail: IMAP> A0010 EXPUNGE fetchmail: IMAP< A0010 OK EXPUNGE completed fetchmail: mail expunge mismatch (0 actual != 1 expected) fetchmail: IMAP> A0011 LOGOUT fetchmail: IMAP< * BYE Closing connection fetchmail: IMAP< A0011 OK LOGOUT completed fetchmail: client/server synchronization error while fetching from domain\user@localhost fetchmail: 6.3.19 querying localhost (protocol IMAP) at Tue 03 Jul 2012 09:46:36 AM EDT: poll completed Merged UID list from localhost: <empty> fetchmail: Query status=7 (ERROR) fetchmail: normal termination, status 7

  Read the article

• Career development as a Software Developer without becoming a manager.

  - by albertpascual

  I’m a developer, I like to write new exciting code everyday, my perfect day at work is a day that when I wake up, I know that I have to write some code that I haven’t done before or to use a new framework/language/platform that is unknown to me. The best days in the office is when a project is waiting for me to architect or write. In my 15 years in the development field, I had to in order to get a better salary to manage people, not just to lead developers, to actually manage people. Something that I found out when I get into a management position is that I’m not that good at managing people, and not afraid to say it. I do not enjoy that part of the job, the worse one, takes time away from what I really like. Leading developers and managing people are very different things. I do like teaching and leading developers in a project. Yet most people believe, and is true in most companies, the way to get a better salary is to be promoted to a manager position. In order to advance in your career you need to let go of the everyday writing code and become a supervisor or manager. This is the path for developers after they become senior developers. As you get older and your family grows, the only way to hit your salary requirements is to advance your career to become a manager and get that manager salary. That path is the common in most companies, the most intelligent companies out there, have learned that promoting good developers mean getting a crappy manager and losing a good resource. Now scratch everything I said, because as I previously stated, I don’t see myself going to the office everyday and just managing people until is time to go home. I like to spend hours working in some code to accomplish a task, learning new platforms and languages or patterns to existing languages. Being interrupted every 15 minutes by emails or people stopping by my office to resolve their problems, is not something I could enjoy. All the sudden riding my motorcycle to work one cold morning over the Redlands Canyon and listening to .NET Rocks podcast, Michael “Doc” Norton explaining how to take control of your development career without necessary going to the manager’s track. I know, I should not have headphones under my helmet when riding a motorcycle in California. His conversation with Carl Franklin and Richard Campbell was just confirming everything I have ever did with actually more details and assuring that there are other paths. His method was simple yet most of us, already do many of those steps, Mr. Michael “Doc” Norton believe that it pays off on the long run, that finally companies prefer to pay higher salaries to those developers, yet I would actually think that many companies do not see developers that way, this is not true for bigger companies. However I do believe the value of those developers increase and most of the time, changing companies could increase their salary instead of staying in the same one. In short without even trying to get into the shadow of Mr. Norton and without following the steps in the order; you should love to learn new technologies, and then teach them to other geeks. I personally have learn many technologies and I haven’t stop doing that, I am a professor at UCR where I teach ASP.NET and Silverlight. Mr Norton continues that after than, you want to be involve in the development community, user groups, online forums, open source projects. I personally talk to user groups, I’m very active in forums asking and answering questions as well as for those I got awarded the Microsoft MVP for ASP.NET. After you accomplish all those, you should also expose yourself for what you know and what you do not know, learning a new language will make you humble again as well as extremely happy. There is no better feeling that learning a new language or pattern in your daily job. If you love your job everyday and what you do, I really recommend you to follow Michael’s presentation that he kindly share it on the link below. His confirmation is a refreshing, knowing that my future is not behind a desk where the computer screen is on my right hand side instead of in front of me. Where I don’t have to spent the days filling up performance forms for people and the new platforms that I haven’t been using yet are just at my fingertips. Presentation here. http://www.slideshare.net/LeanDog/take-control-of-your-development-career-michael-doc-norton?from=share_email_logout3 Take Control of Your Development Career Welcome! Michael “Doc” Norton @DocOnDev http://docondev.blogspot.com/ [email protected] Recovering Post Technical I love to learn I love to teach I love to work in teams I love to write code I really love to write code What about YOU? Do you love your job? Do you love your Employer? Do you love your Boss? What do you love? What do you really love? Take Control Take Control • Get Noticed • Get Together • Get Your Mojo • Get Naked • Get Schooled Get Noticed Get Noticed Know Your Business Get Noticed Get Noticed Understand Management Get Noticed Get Noticed Do Your Existing Job Get Noticed Get Noticed Make Yourself Expendable Get Together Get Together Join a User Group Get Together Help Run a User Group Get Together Start a User Group Get Your Mojo Get Your Mojo Kata Get Your Mojo Koans Get Your Mojo Breakable Toys Get Your Mojo Open Source Get Naked Get Naked Run with Group A Get Naked Do Something Different Get Naked Own Your Mistakes Get Naked Admit You Don’t Know Get Schooled Get Schooled Choose a Mentor Get Schooled Attend Conferences Get Schooled Teach a New Subject Get Started Read These (Again) Take Control of Your Development Career Thank You! Michael “Doc” Norton @DocOnDev http://docondev.blogspot.com/ [email protected] In a short summary, I recommend any developer to check his blog and more important his presentation, I haven’t been lucky enough to watch him live, I’m looking forward the day I have the opportunity. He is giving us hope in the future of developers, when I see some of my geek friends moving to position that in short years they begin to regret, I get more unsure of my future doing what I love. I would say that now is looking at the spectrum of companies that understand and appreciate developers. There are a few there, hopefully with time code sweat shops will start disappearing and being a developer will feed a family of 4. Cheers Al tweetmeme_url = 'http://weblogs.asp.net/albertpascual/archive/2010/12/07/career-development-as-a-software-developer-without-becoming-a-manager.aspx'; tweetmeme_source = 'alpascual';

  Read the article

< Previous Page | 570 571 572 573 574 575 576 577 578 579 580 581  | Next Page >