Search Results

Search found 16417 results on 657 pages for 'computer linguist'.

Page 575/657 | < Previous Page | 571 572 573 574 575 576 577 578 579 580 581 582  | Next Page >

• BIOS not detecting working SATA hard drive.

  - by Evan

  Some time ago my power supply died. It's a long story from then till now, but the important bit is that I ended up with a new hard drive and a new power supply. I tested to see if my original hard drive was still alive, and it booted and worked perfectly until I turned it off. When I started it again it would not boot. I bought new SATA cables, assuming that the one I had was not seating properly (it was cheap and wobbly), but no dice. Upon start-up I am presented with a message telling me to insert boot media into the selected drive or add a drive and restart. Neither the new or the old drive is detected by BIOS, my Vista install disk, or from my bootable Linux USB drive. When I remove all of the RAM the computer ceases outputting visual information, and upon reinstalling the ram and starting up again gives me a "failed overclock" error. So, does anyone have an idea as to what might be going on? I'm completely lost at this point.

  Read the article

• Subdocument in Word won't save

  - by ChrisW

  Because I know Word has a history of not liking very large documents (my supervisor specifically told me not to use LaTeX... grr), I decided to learn the Master document / subdocument feature of Word when writing my PhD thesis. I have the title page / table of contents etc in the master document, and each chapter as a separate document. However, when I save the master document, it appears to save all the chapter documents apart from one (Chapter 4), for which it brings up the Save Document dialog box, helpfully with "Chapter4.docx" in the "Save as" box (n.b. Chpater4.dox is not open). Clicking save does nothing, and doesn't make the dialog box go away. Saving as a different document means that my changes aren't reflected in the same document. There must be some reason Word doesn't like this particular document but I've got no idea why - there's nothing special in it that isn't in any of the other chapters. I have tried closing all documents, renaming Chapter4.docx, opening the master document, expanding all documents, OKing the warning that Chapter4.dox does not exist, and inserting the 'new' document, but even when I save the master document it still won't save the new Chapter4 document. If anyone knows any reason why Word is acting like this (or if I'm doing anything stupid), I'll be eternally grateful (p.s. sorry for the long rambling message. It's late; I've been working on my PhD 4.5 years, I really really want to throw this computer out the window, and I hope people are kind enough not to downvote this question because of it's rambling nature!) Update With Word closed, I've tried to delete Chapter4.docx (having made a backup!) - but I get a warning that it can't be deleted because it's open in Microsoft Word... these files are on a network drive and the same problems are happening on 2 different computers. I could login to the filestore through ssh and force the file to be deleted, but I'm curious to know why this is happening!

  Read the article

• Fixing a typo in machine name

  - by justSteve

  When i installed windows i had a typo in the machine name that i corrected from the system's 'Computer Name/Domain Changes' - the workstation is a member of a workgroup not a domain. From everything i can see the renamed machine name is correct. Shift gears.... I'm importing SQL logins from my remote server to this, my development workstation and have used the script presented here - a script that generates a CREATE statement for each login found. While I was preparing to run this script's output (from the remote box) i needed to change the domain name from the remote to my local's name - so i ran the same script locally (in order to see what SQL things my domain name is. SQL has the original machine name - the one with the typo. However, the scripts are tossing errors if i try to create logins with that identifier. CREATE LOGIN [Setve\Admin] FROM WINDOWS WITH DEFAULT_DATABASE = [master] But works correctly if i use the updated machine name: CREATE LOGIN [Steve\Admin] FROM WINDOWS WITH DEFAULT_DATABASE = [master] So the problem is: do i have a problem i need to solve? Somewhere, deep in the guts of SQL Server, it has record of a Domain name that does not exist. Should i find and fix that discrepancy? thx

  Read the article

• Sharing a folder with Nautilus and NTFS external drive gets errors

  - by TheLQ

  I am trying to share a folder in Lubuntu over a network that's on an external NTFS drive. Due to the system that I have (rotating backup disks) this is probably the second time that the drive would of been mounted. Its manually mounted with a simple (for example) mount /dev/sdb1 /media/BACKUP On an internal NTFS disk I have successfully setup a network share and can access it. However on the external disk I can't from any other Windows computer. When setting up the share Nautilus said that it needs to change the other's permissions to allow for other users to write. However afterwords its still blank. Changing it to Read and Write just changes back to blank. Chowning the entire /media folder recursively and trying didn't work. Running PCManFM as root and changing didn't work. Adding "public=yes" to smb.conf and restarting didn't work. I'm out of idea's on what to do. What's weird is that it worked just fine on an internal NTFS disk, so why not the external one? Any solutions need to be able to managed inside of a gui (preferably Nautilus) as the person managing the machine isn't as tech savvy. Thanks

  Read the article

• Host name change breaking http? Fedora

  - by Dave

  OK so I have been messing around on my development server. It has been a while since I have had my head in linux and I suspect I have broken something. I have SSH running and that is working fine. I also have HTTP and I had FTP running also. Earlier today I decided I wanted to rename the machine so I updated the /etc/hosts file and /etc/sysconfig/network. I also changed the server name in the httpd.conf. I rebooted the machine and reconnected to SSH fine. Later I was messing around with the FTP service (trying to tighten up the user security) and when i tried to connect remotely to FTP no joy, it said cannot connect. I thought that was weird but had planned to remove ftp as we will be using github so removed ftp and moved on. Then I tried to connect to the website but major fail. even connecting to the IP address is failing. I used lynx to connect to the localhost and there was my site so something going on at server level. I thought maybe something up with iptables but I have not changed them but tried adding http but still no joy. I have a - Fedora release 17 (Beefy Miracle) NAME=Fedora VERSION="17 (Beefy Miracle)" ID=fedora VERSION_ID=17 PRETTY_NAME="Fedora 17 (Beefy Miracle)" ANSI_COLOR="0;34" CPE_NAME="cpe:/o:fedoraproject:fedora:17" Fedora release 17 (Beefy Miracle) Fedora release 17 (Beefy Miracle) Linux version 3.3.4-5.fc17.x86_64 ([email protected]) (gcc version 4.7.0 20120504 (Red Hat 4.7.0-4) (GCC) ) #1 SMP Mon May 7 17:29:34 UTC 2012 This is my iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT icmp -- anywhere anywhere ACCEPT all -- anywhere anywhere ACCEPT tcp -- anywhere anywhere state NEW tcp dpt:ssh REJECT all -- anywhere anywhere reject-with icmp-host-prohibited Chain FORWARD (policy ACCEPT) target prot opt source destination REJECT all -- anywhere anywhere reject-with icmp-host-prohibited Chain OUTPUT (policy ACCEPT) target prot opt source destination Like I say I can use SSH no issue but http although running is a no go from a remote computer. Any ideas?

  Read the article

• I have enabled hidden administrator in Win 7 home, but programs still dont work.

  - by Angela

  I have Windows 7 Home Premium, and would like to do some maintenance tasks such as running Disk Defragmenter. However, this and other programs and applications that I'm accustomed to using are now blocked. For these programs, there is a shield icon next to their icons and nothing happens when I click on them. I notice that the screen blinks slightly, but I do not get prompted for a password and the program still does not run. It seems these programs may only be accessible through an Administrator account. However, right-clicking and selecting "Run As Administrator" does not work. After some research, I found a way to enable the hidden built-in Administrator account. I booted the computer into safe mode. In the command prompt, I typed net user administrator /active:yes. I gave the account a password. I rebooted the system. There is now an Administrator account on the home screen. However, the locked programs behave no differently for me when I use this account. What could cause this problem? How can I fix it?

  Read the article

• Windows 7 boots to black screen with blinking cursor

  - by murgatroid99

  I have an Alienware M17x that dual boots into Ubuntu 11.04 and Windows 7 Home Premium. Currently, the computer starts at the GRUB loader and will boot into Ubuntu, but if I try to boot into Windows, I immediately get a black screen with a blinking cursor in the upper left corner. The output of fdisk -l is Device Boot Start End Blocks Id System /dev/dm-0p1 1 5 40131 de Dell Utility Partition 1 does not start on physical sector boundary. /dev/dm-0p2 6 1918 15360000 7 HPFS/NTFS Partition 2 does not start on physical sector boundary. /dev/dm-0p3 * 1918 64772 504878877+ 7 HPFS/NTFS Partition 3 does not start on physical sector boundary. /dev/dm-0p4 64772 77827 104858625 5 Extended Partition 4 does not start on physical sector boundary. /dev/dm-0p5 64772 67204 19531008 83 Linux /dev/dm-0p6 67204 74498 58593536 83 Linux /dev/dm-0p7 74498 77577 24731648 83 Linux /dev/dm-0p8 77578 77827 2000128 82 Linux swap / Solaris I have used the Windows rescue CD, and run the automatic error fixer until it finds no errors. I have run chkdsk /R on both the main Windows 7 (/dev/dm-0p3) partition and the recovery partition (/dev/dm-0p2). I set the main Windows 7 partition to be active. I also tried running in the recovery console the commands bootrec /fixmbr bootrec /fixboot bootrec /rebuildbcd None of these helped and the last set of commands deletes grub, which I then have to reinstall from Ubuntu. I think the last thing I did in windows before this started was install the newest ATI driver for my video card. This would suggest using system restore, and I actually had a restore point earlier (after the problem started), but after whatever I did that restore point does not appear in the list on the recovery disk any more, so I cannot do a system restore. Is there anything else I can try to make Windows boot properly again? Edit: Running the suggested commands bootsect /nt60 c: bcdboot c:\windows /s c: was also ineffective.

  Read the article

• How to set up simple VPN for secure Internet connections over unencrypted Wi-Fi on Windows?

  - by Senseful

  I'm looking for a solution similar to the one in this question, except that I don't have a linux computer. I have windows computers that could be set up to accept VPN connections. Preferably I want to set this up on either Windows Server 2003 or Windows XP. I'd like to connect different devices (e.g. iPhone, iPad, laptops, etc.) that are on open unsecure wireless networks (e.g. the one's you see at places like Starbucks) to this VPN to ensure that all my data is secure. I found an article that shows that you can enable VPN connections on Windows XP. After following those steps, though, I'm not sure what to do. Which ports do I open on my firewall? Which VPN settings do I use on my devices such as the iPhone? Do I use L2TP, PPTP, or IPSec? What's the difference between these? Are there any other steps missing in that tutorial? I'm hoping that since Windows has this built in feature, that it will be much simpler to set up rather than having to deal with setting up something such as OpenVPN. If I follow those settings and enable port forwarding on port 1723, and then use the following settings on the iPhone: PPTP (IP Address) RSA SecurID: Off Encryption Level: Auto Send All Traffic: On Proxy: Off It shows "Connecting..." then "Disconnecting..." and the following error message: VPN Configuration A connection could not be established to the PPP server. Try reconnecting. If the problem continues, verify your settings and contact your Administrator. I'm using a user account that I enabled privileges to in the VPN settings on the Windows machine.

  Read the article

• conflicting info about the running kernel version in FreeBSD

  - by John

  I asked a related question about uname before, now want to ask from another angle because the following simple yet obvious conflicting outputs may mean there is something many people did not think of (me included). I'm running FreeBSD 9 RELEASE, please see the following commands: # sysctl kern.bootfile kern.bootfile: /boot/kernel/kernel # strings /boot/kernel/kernel |grep RELEASE|grep 9 @(#)FreeBSD 9.2-RELEASE-p7 #0: Tue Jun 3 11:05:13 UTC 2014 FreeBSD 9.2-RELEASE-p7 #0: Tue Jun 3 11:05:13 UTC 2014 9.2-RELEASE-p7 The above kernel file suggests the running kernel is 9.2-RELEASE-p7. But... # dmesg Copyright (c) 1992-2012 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 9.1-RELEASE #0 r243825: Tue Dec 4 09:23:10 UTC 2012 ... # uname -a FreeBSD localhost.localdomain 9.1-RELEASE FreeBSD 9.1-RELEASE #0 r243825: Tue Dec 4 09:23:10 UTC 2012 [email protected]:/usr/obj/usr/src/sys/GENERIC amd64 So dmesg and uname says it's 9.1-RELEASE. I also did an extensive find / -type f -exec grep -l "9.1-RELEASE" {} \; but found no possible kernel file that contains 9.1-RELEASE. What could lead to the above conflict, and what kernel I am actually running? Please note I run RELEASE and ran freebsd-update to do binary update, so no compiled kernel is involved. And I have rebooted multiple times after freebsd-update. And the system is not in jail etc, just the only system on that computer.

  Read the article

• How to access a port via OpenVpn only

  - by Andy M

  I've set up an openvpn server alongside an apache website that can only be accessed on port 8100 on the same machine. My /etc/openvpn/server.conf file looks like this: port 1194 proto tcp dev tun ca ./easy-rsa2/keys/ca.crt cert ./easy-rsa2/keys/server.crt key ./easy-rsa2/keys/server.key # This file should be kept secret dh ./easy-rsa2/keys/dh1024.pem # Diffie-Hellman parameter server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt # make sure clients can still connect to the internet push "redirect-gateway def1 bypass-dhcp" keepalive 10 120 comp-lzo persist-key persist-tun status openvpn-status.log verb 3 Now I tried to let only clients connected to the vpn network access the website on apache via port 8100. So I defined a few iptables rules: #!/bin/sh # My system IP/set ip address of server SERVER_IP="192.168.0.2" # Flushing all rules iptables -F iptables -X # Setting default filter policy iptables -P INPUT DROP iptables -P OUTPUT DROP iptables -P FORWARD DROP # Allow incoming access to port 8100 from OpenVPN 10.8.0.1 iptables -A INPUT -i tun0 -p tcp --dport 80 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o tun0 -p tcp --sport 80 -m state --state ESTABLISHED -j ACCEPT # outgoing http iptables -A OUTPUT -o tun0 -p tcp --dport 80 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A INPUT -i tun0 -p tcp --sport 80 -m state --state ESTABLISHED -j ACCEPT Now when I connect to the server from my client computer and try to access the website on 192.168.0.2:8100, my browser can't open it. Will I have to forward traffic from tun0 to eth0? Or is there anything else I'm missing?

  Read the article

• What could cause an 101 Error in WAMP under Windows 7 ?

  - by Brayn

  Hey, I'be been using WAMP for local development for quite a while now but lately I've been getting an Error 101 message when I browse localhost sites. It's possible for this to have appeared after the last WAMP update but I'm not 100% sure on this. If I try again and again, after several page refreshes it works but it's really annoying! The exact error message is: Error 101 (net::ERR_CONNECTION_RESET): Unknown error. This is my configuration: OS: Windows 7 Apache: 2.2.11 PHP: 5.2.9-2 WAMP: 2.0 Also the local scripts connect to a remote MySQL server, they don't use the local MySQL(I don't know if it matters, just though I let you know). I've been looking into the apache logs and I've found the following. It seems that the apache server keeps restarting and I can't figure why: [Wed Oct 14 13:52:30 2009] [notice] Parent: child process exited with status 255 -- Restarting. [Wed Oct 14 13:52:30 2009] [notice] Apache/2.2.11 (Win32) PHP/5.2.9-2 configured -- resuming normal operations [Wed Oct 14 13:52:30 2009] [notice] Server built: Dec 10 2008 00:10:06 [Wed Oct 14 13:52:30 2009] [notice] Parent: Created child process 6784 [Wed Oct 14 13:52:31 2009] [notice] Child 6784: Child process is running [Wed Oct 14 13:52:31 2009] [notice] Child 6784: Acquired the start mutex. [Wed Oct 14 13:52:31 2009] [notice] Child 6784: Starting 64 worker threads. [Wed Oct 14 13:52:31 2009] [notice] Child 6784: Starting thread to listen on port 80. [Wed Oct 14 13:52:32 2009] [notice] Parent: child process exited with status 255 -- Restarting. [Wed Oct 14 13:52:33 2009] [notice] Apache/2.2.11 (Win32) PHP/5.2.9-2 configured -- resuming normal operations [Wed Oct 14 13:52:33 2009] [notice] Server built: Dec 10 2008 00:10:06 [Wed Oct 14 13:52:33 2009] [notice] Parent: Created child process 3572 [Wed Oct 14 13:52:33 2009] [notice] Child 3572: Child process is running [Wed Oct 14 13:52:33 2009] [notice] Child 3572: Acquired the start mutex. [Wed Oct 14 13:52:33 2009] [notice] Child 3572: Starting 64 worker threads. [Wed Oct 14 13:52:33 2009] [notice] Child 3572: Starting thread to listen on port 80. Also I've checked Windows Firewall and disabled any other protection that I have on this computer with no improvement. Thanks!

  Read the article

• Can I connect a Playstation 3's HDMI output to my monitor's DVI-D input? [migrated]

  - by HankJDoomstorm

  I'm attempting to connect my Playstation 3 to my computer monitor. The monitor has a DVI-D (dual link) input, so before distinguishing between the different DVI varieties, I bought a DVI-I (dual link) to HDMI converter that won't fit into the port on the monitor (not only that, there isn't enough physical space in the back of the monitor to fit that much stuff before it hits the bottom of it). So I grabbed a DVI-D (single link) cable and got a female-to-female DVI-I coupler, and plugged the DVI-D cable into the monitor and the whole mess of converters. The end result was HDMI to DVI-D single link, but my monitor isn't receiving a signal on its digital channel. (For clarity's sake: DVI-D DL input on Monitor, DVI-D SL cable, DVI-I DL female-to-female coupler, DVI-I DL to HDMI converter, HDMI output on PS3) I don't know much about this stuff (obviously), but my educated guess is that the bandwidth of the PS3 is too high for the DVI-D Single Link cable, so nothing's getting through. Will replacing the single link cable with dual link resolve this? If not, is it possible at all? Oh, I should mention I'm aware I won't get audio through the monitor. I have an RCA to 3.5mm converter for that.

  Read the article

• Why is the Windows 8 recycle bin using more space than it is allocated?

  - by oldmankit

  I ran WinDirStat to scan the contents of my hard drive. I was surprised to see that the $RECYCLE.BIN folder on my D: drive takes 26 GB of space. I emptied the recycle bin, refreshed the folder in WinDirStat, but it still takes 26 GB of space. I reduced the Maximum size of the recycle bin for this drive to 10000 MB for the main user of this computer, and disabled the recycle bin for the other user, and refreshed the folder in WinDirStat, but it still takes 26 GB of space. I ran (in an elevated window) rd /s D:\$Recycle.bin, and refreshed the folder in WinDirStat, and finally it became empty. Why was it taking up space even after I emptied it? Why was it taking more space (26 GB) than the maximum allowed amount (10 GB)? Update: After six months of using Windows (no re-install and no changes of settings related to the Recycle Bin) I used WinDirStat to check how big D:\$RECYCLE.BIN has become. It is now 29 GB. In Recycle Bin Properties, I select drive D, and it is still a custom maximum size (10000 MB).

  Read the article

• Immediate logout after login with PAM, Kerberos, and LDAP

  - by Dylan Klomparens

  I've set up remote login on a computer using Kerberos and LDAP. I've also configured NFS to mount onto /home so that the user's home directory is the same wherever they login. Kerberos authentication seems to work fine. I can get a ticket using kinit user1 (assuming user1 is a remote user) and see the ticket with klist. I'm pretty sure LDAP is working because I see the proper output from getent passwd, which lists all the remote users. The contents of /home are present when I list the files. The problem is: when I try to login as a remote user the session is immediately ended. Why is it not letting me stay logged in? Here is the output from /var/log/messages after a login attempt: # /var/log/messages: Oct 9 10:57:53 tophat login[6472]: pam_krb5[6472]: authentication succeeds for 'user1' ([email protected]) Oct 9 10:57:53 tophat login[6472]: pam_krb5[6472]: pam_setcred (establish credential) called Oct 9 10:57:53 tophat login[6472]: pam_krb5[6472]: pam_setcred (delete credential) called EDIT: The distro is openSUSE. Here are the common-* files in /etc/pam.d:   # /etc/pam.d/common-account account required pam_unix.so   # /etc/pam.d/common-auth auth sufficient pam_krb5.so minimum_uid=1000 auth required pam_unix.so nullok_secure try_first_pass   # /etc/pam.d/common-session session optional pam_umask.so umask=002 session sufficient pam_krb5.so minimum_uid=1000 session required pam_unix.so There doesn't appear to be a /var/log/auth.log file nor a /var/log/secure file.

  Read the article

• Daisychain external USB drive to WD My Book World Edition (Blue rings)

  - by d03boy

  I recently bought a new My Book Essential 1TB (WDBACW0010HBK-NESN) to daisychain to my older My Book World Edition 500GB (blue rings) with one of the version 01.xx.xx firmwares. At first when I connected the USB drive to the MBWE, it showed up in the System Summary section of the administration page without any issue. I was able to set up a new share on the new drive. The administration website moved very, very slow though. The administration pages became nearly unresponsive during this setup process. Once the share was set up I could access the new share but again, it was very slow, now through Windows Explorer. I looked around the internet and it seems that this is caused by the USB drive being formatted with NTFS. I tried reformatting it (again, as NTFS) just to double check and the same problem occurred. I then tried FAT32 but realized it would only support files of approximately 2GB and that is not acceptable for me. I decided to try a firmware upgrade on the MBWE to version 02.00.19. The firmware upgrade completed successfully but now the MBWE does not display the USB drive in the System Summary like it did with the earlier firmware version. The USB drive works perfectly fine when connected directly to my computer. Is there a way to solve this issue?

  Read the article

• Ubuntu hard disk getting SATA errors

  - by Henadzy

  I am getting "UNC" errors on a hard disk on Ubuntu 9.10. It slows down my system, applications have not been responding for a long time. But when I mount the filesystem on another computer, it works properly. disk: SAMSUNG HD161HJ (SATA) syslog: Apr 25 00:28:25 vare6gin kernel: [ 885.773839] ata3.00: exception Emask 0x1 SAct 0x1e SErr 0x0 action 0x6 frozen Apr 25 00:28:25 vare6gin kernel: [ 885.773845] ata3.00: Ata error. fis:0x21 Apr 25 00:28:25 vare6gin kernel: [ 885.773861] ata3.00: cmd 60/08:08:3f:00:ad/00:00:10:00:00/40 tag 1 ncq 4096 in Apr 25 00:28:25 vare6gin kernel: [ 885.773864] res 51/40:24:67:c8:91/40:00:05:00:00/40 Emask 0x9 (media error) Apr 25 00:28:25 vare6gin kernel: [ 885.773871] ata3.00: status: { DRDY ERR } Apr 25 00:28:25 vare6gin kernel: [ 885.773877] ata3.00: error: { UNC } [...snip 3 similar repeats of last 4 lines; see revision history for full log...] Apr 25 00:28:25 vare6gin kernel: [ 885.773970] ata3: hard resetting link Apr 25 00:28:25 vare6gin kernel: [ 885.773974] ata3: nv: skipping hardreset on occupied port Apr 25 00:28:25 vare6gin kernel: [ 886.240073] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Apr 25 00:28:25 vare6gin kernel: [ 886.256277] ata3.00: configured for UDMA/133 Apr 25 00:28:25 vare6gin kernel: [ 886.256305] ata3: EH complete Apr 25 00:28:27 vare6gin kernel: [ 888.176088] ata3: EH in SWNCQ mode,QC:qc_active 0xF sactive 0xF Apr 25 00:28:27 vare6gin kernel: [ 888.176099] ata3: SWNCQ:qc_active 0xF defer_bits 0x0 last_issue_tag 0x3 Apr 25 00:28:27 vare6gin kernel: [ 888.176102] dhfis 0xF dmafis 0x1 sdbfis 0x0 Apr 25 00:28:27 vare6gin kernel: [ 888.176109] ata3: ATA_REG 0x51 ERR_REG 0x40 Apr 25 00:28:27 vare6gin kernel: [ 888.176113] ata3: tag : dhfis dmafis sdbfis sacitve Apr 25 00:28:27 vare6gin kernel: [ 888.176120] ata3: tag 0x0: 1 1 0 1 Apr 25 00:28:27 vare6gin kernel: [ 888.176126] ata3: tag 0x1: 1 0 0 1 Apr 25 00:28:27 vare6gin kernel: [ 888.176131] ata3: tag 0x2: 1 0 0 1 Apr 25 00:28:27 vare6gin kernel: [ 888.176136] ata3: tag 0x3: 1 0 0 1

  Read the article

• Windows 2008 R2 RDS - Double Login

  - by colo_joe

  Issue: Double logins when connecting to RemoteApps or Remote Desktop Environment: Gateway = 1 server 2008 R2 - Roles = Gateway, Session Broker, Connection Mgr, Session Host Configuration server Session hosts = 2 servers 2008 R2 - Roles = App Manager and Session host configuration Testing: I can get to the url http://RDS.domain.com/rdweb - I get prompted for authentication (1) Pass authentication, get list of remote apps. Click on remoteapps or remote desktop, get prompted for authentication again (2). Pass authentication, I get access to app or RDP. Done so far. On session host Signed rdp files with cert. Added the following to the custom RDP settings: Authenticaton level:i:0 = If server authentication fails, connect to the computer without warning (Connect and don’t warn me). prompt for credentials on client:i:1 = RDC will prompt for credentials when connecting to a server that does not support server authentication. enablecredsspsupport:i:1 = RDP will use CredSSP, if the operating system supports CredSSP. Edited the javascript file as found in http://support.microsoft.com/kb/977507 Added Connection ID, and added Web Access server to TS Web Access Computers group on the Session host servers, and Signed apps as found in hxxp://blogs.msdn.com/b/rds/archive/2009/08/11/introducing-web-single-sign-on-for-remoteapp-and-desktop-connections.aspx Note: This double login happens internally and externally.

  Read the article

• Two different subwoofers aren't working on my machine or my phone

  - by Philluminati

  I have speakers that come with my computer. Two small desktop speakers and a subwoofer with a base volume control on the back. It's worked for years. I was listening to Spotify on my speakers as loud they would possibly go and with the base turned up to max and suddenly the subwoofer stopped working. I've plugged the speakers into my Android HTC Desire Z handset and again, the desktop speakers play music but the subwoofer doesn't (even after fiddling with the volume control). So I figured I'd broken it. I went to Amazon and bought a replacement one. I bought this one: http://www.amazon.co.uk/dp/B002N46YD8/ref=pe_217191_31005151_dp_1 but it doesn't work either, on either my desktop nor my Android phone. I had a play with alsamixer and the LFE and center controls are switched on and the speakers are okay... but still no base. Am I unlucky enough to bought a new subwoofer which is already broken out of the box or is there something else which is wrong and I could look into please? Are there any other tests which I could perform to see if the problem is me or not?

  Read the article

• Windows 7 shows a drive as full in summary but files shown on drive are very small

  - by Rob

  I have a drive partitioned so it is seen by Windows as 2 drives: C:\ and D:\ Windows 7 shows D:\ as full up in the graphical summary in 'My Computer' summary of all the drives, e.g. the bar graph indicates full and nearly all of the drive's capacity, 108Gb, is full. So I go into the D:\ drive to look at the files, I see several folders. I select them all and the right-click menu Properties to count their size, expecting the value to be about the same as what Windows reports in the summary, i.e. nearly 108Gb. But the properties window shows the files are very small, Kbs and Mbs, nowhere near 108Gbs. One of the folders is a backup, but its size is very small. I've checked the folder options to show all system files and hidden files too - and counted these in the properties. Something invisible is holding the space. What is happening here? I'm afraid to delete anything if it removes valuable backups. Have I got huge backups here? Why can't I see them? How do I see them?

  Read the article

• Not able to access external Hard disk

  - by Jash Jacob

  I have a 1TB External Hard drive which I'm currently not able to access. When I open the External drive in Finder, It shows it's empty. When I use the option to "Get Info", I get the dialog box stating it has about 300GB Free. Tried to get into the External Drive using Terminal, I had no luck. Checking in Disk Utility, It showed that I have many number of files but ZERO folder. I tried to "repair disk", in the process the external Drive got unmounted in between the process. I checked this drive on Windows. I was able to open almost all the folders but I wasn't able to copy anything onto the external drive. One folder caused my windows computer to hang, So i connected the drive back onto my MacBook Pro and tried to access the drive through terminal (this time it worked!) and then I tried to delete the folder with rm command, I got an "input/output error" What should i do to recover the files in that folder? How can i access my external drive on my mac

  Read the article

• Domain Trust 2008 to 2003

  - by nick3216

  I'm having trouble setting up the trust relationship between a Windows Server 2003 and a Windows Server 2008 AD. Domain a is Windows Server 2003 Forest functional level. Domain b is a Windows Server 2008 Forest functional level. I can set up the incoming side of the trust relationship on domain "a" so that it trusts domain "b". Try as I might on domain "b" I can't set up the outgoing side of the trust relationship to domain "a". The GUI interface gives an unhelpful 'The request is not supported'. I'm not sure netdom is being more or less helpful as it refers me to FilterSIDs netdom trust /add b /uo:b\admin /po:* /d:a /ud:a\admin /pd:* /oneside:trusting To improve the security of this external trust, security identifier (SID) filtering is enabled, however, if users have been migrated to the trusted domain and their SID histories have been preserved, you may choose to turn off this feature. For more information about SID filtering and how to turn it off, see the help for netdom trust /FilterSids or see Help and Support. The request is not supported. The command failed to complete succesfully. I say 'less helpful' because Windows Server 2008 doesn't support the /FilterSIDs option. How can we force creation of this trust? Edit: Just to clarify I've checked that the [Computer Configuration\Windows Settings\Security Settings\Local Policies\Security Options] "Network access: Allow anonymous SID/Name translation” is enabled on both sides of the trust as per http://social.technet.microsoft.com/Forums/en/winserverDS/thread/cc61fc25-3569-4413-bbfd-92390eb31118

  Read the article

• What is the quickest and safest way to test new software and revert all changes, if needed?

  - by calbar

  I'm looking for Windows software that will allow me to quickly create a "checkpoint", do whatever I might need to do to my computer - install programs/drivers/updates, create/delete personal files, reboot the system multiple times, open questionable attachments - and then revert the entire system back to when the checkpoint was created. Essentially I want Windows Restore Points that save my personal files and partitions, too. It sounds like disk imaging might be the ticket, but creating them is much too slow and the restore process too involved... I'm hoping to sacrifice full disaster recovery for speed. Creating a checkpoint should be as close to one-click as possible, and rolling back should be a matter of selecting a restore point and rebooting. Ding! I'm familiar with Sandboxie, True Image Home "Try and Decide", Returnil, and a number of other "virtual system" apps that actively "catch" changes and allow you to commit or reject them. I'm not interested in these for a number of reasons - I prefer the "cut and dry" restore point approach. Finally, I'll note that I've just recently become aware of Comodo Time Machine. It sounds absolutely perfect, however, a quick skim through the user forums show more than a few horror stories of corrupted, unbootable systems. Any positive personal experience with the software to suppress my superstitions, or suggestions for more established alternatives would be greatly appreciated - Comodo Time Machine seems relatively new. Thanks for your help!

  Read the article

• server 2008 r2 stuck on installing updates

  - by volody

  I have 2008 r2 64bit server that is stuck on installing updates. It shows message "Please do not power off or unplug your machine. Installing 57 of 61.." This message is shown for 3 hours now. I was trying to connect to this server using mmc. runas /user:AdministratorAccountName@ComputerName "mmc %windir%\system32\compmgmt.msc" RUNAS ERROR: Unable to run - mmc C:\Windows\system32\compmgmt.msc 1311: There are currently no logon servers available to service the logon request. What else can I do? Update: Remote Desktop does not work. It just disappear after entering username and password from Win7-64 computer Update: I have disconected server. Now Server Manager in Roles Summary shows message "Unexpected error refreshing Server Manager: The remote procedure call failed." Event log shows Could not discover the state of the system. An unexpected exception was found: System.Runtime.InteropServices.COMException (0x800706BE): The remote procedure call failed. (Exception from HRESULT: 0x800706BE) at System.Runtime.InteropServices.Marshal.ThrowExceptionForHRInternal(Int32 errorCode, IntPtr errorInfo) at Microsoft.Windows.ServerManager.ComponentInstaller.ThrowHResult(Int32 hr) at Microsoft.Windows.ServerManager.ComponentInstaller.CreateSessionAndPackage(IntPtr& session, IntPtr& package) at Microsoft.Windows.ServerManager.ComponentInstaller.InitializeUpdateInfo() at Microsoft.Windows.ServerManager.ComponentInstaller.Initialize() at Microsoft.Windows.ServerManager.Common.Provider.RefreshDiscovery() at Microsoft.Windows.ServerManager.LocalResult.PerformDiscovery() at Microsoft.Windows.ServerManager.ServerManagerModel.CreateLocalResult(RefreshType refreshType) at Microsoft.Windows.ServerManager.ServerManagerModel.InternalRefreshModelResult(Object state) Update: Manual update hangs on (Installing update 58 of 62...) Seurity Update for Windows Server 2008 R2 x64 Edition (KB979309) Update: It could be an issue with that admin user was renamed

  Read the article

• Connection to Google, Yahoo, Bing, Ask, etc. compromised via all devices on my home network - How?

  - by jt0dd

  I'm a very computer savvy guy (although not very networking savvy), and I may still be wrong about this, but I think my home network may be compromised somehow. I'd like to know if it's possible for someone to have hijacked my network's connection to Google.com and other popular websites. Update: The issue seems to take effect with all popular websites. I can connect to small (non-popular) websites without issue, but Facebook, Google, Yahoo, and Bing cannot be accessed by any device on my home network. On all devices using my home network, I'm being shown http://www.google.com WARNING! Internet Explorer is currently out of date. Please update to continue. when I attempt to connect to google.com. I wouldn't be surprised by this at all if it were just the laptop. It's the fact that this is happening on all devices on my network that confuses me. Here's the screenshot from my iPhone, for reference. Can my home network be compromised? Is that even possible? How can something like this happen across all platforms on all devices in the same way? I wouldn't imagine every device / platform on the network would get the same virus. Should I assume that my network's security is totally compromised? Update: All mobile devices and laptops on my home network are experiencing the same alert when attempting to connect to google.com.

  Read the article

• Windows 7 loses correct time zone upon reboot

  - by Android Eve

  I have a standard PC running Windows 7 Ultimate (64-bit). For some reason, it refuses to keep the correct time zone (the BIOS battery is OK) when restarted. Note (1): The Time zone is correct. The "Internet Time" tab also shows "this computer is set to automatically synchronize with 'time.windows.com'. When I click the 'Change settings...' button, the 'Synchronize with an Internet time server' checkbox is checked. Still, upon reboot, the time is skewed by 6 hours... and doesn't correct itself even after waiting hours for this "automatically synchronize" to occur. Note (2): The BIOS time is set to local (i.e. not UTC). When I restart Windows 7 without booting to the other OS installed in dual-boot config (Ubuntu Linux), it seems to correctly remember the time. This may explain immediate time upon reboot, but it doesn't explain why Windows 7 won't automatically 'Synchronize with an Internet time server' even after an hour. Why is this happening and how do I correct this?

  Read the article

< Previous Page | 571 572 573 574 575 576 577 578 579 580 581 582  | Next Page >