Search Results

Search found 15729 results on 630 pages for 'event'.

Page 576/630 | < Previous Page | 572 573 574 575 576 577 578 579 580 581 582 583  | Next Page >

• DPM 2010 "Disk failed or disk not found"

  - by SysAdmin

  I have an HP Proliant ML110 G5 server with Windows server 2008R2 only dedicated for DPM 2010. This server has a limit in HD of 8TB which has already been met. I'm now stuck in this situation where my disk keeps failing "Disk failed or Disk not found" in the disk management. Only after I reboot the system the disk comes back up. Today I was running my monthly tape backup on a certain protection group and the disk failed again while the tape job was running (so the job wasn't completed). This is the description of the error in the alerts: "The disk Disk 1 - Hitachi HDS722020ALA330 SCSI Disk Device cannot be detected or has stopped responding. All subsequent protection activities that use this disk will fail until the disk is brought back online. (ID 3120)". My backup system is becoming useless! I don't think that is a hardware issue (please correct me if I'm wrong) since the HD works fine for a certain period of time which is becoming shorter and shorter. I basically have no more option to fix this problem. I tried to fix any error that was coming up in the event viewer with no luck (included one regarding the SQL2008 compatibility issue). The disk keeps failing! Now I'm only trying to recover/migrate the data from the disk that is having problem but my issue now is that I cannot add any drives to my server since I already got installed the maximum storage capacity 8TB. I thought about 2 simple options. Please tell me what you guys think about it; Unplug one of the 2 storage pool disks (disk0, that one without problem) from the machine and install a new one in order to migrate the data with the Migration tool for DPM. Remove the defective disk (disk1), put back the disk0 and run the synchronization/consistency check on all the groups to recreate replicas and recovery points. Run diskpart.exe and clean up the disk (loosing all data) and hoping that he will work after I sync all the protection groups. Both solutions are not elegant but I have no better options at the moment. Please I need some help. Thanks for your time Angelo

  Read the article

• Using an SSD with no AHCI [ICH7 base] - Windows 7 hangs frequently

  - by h4xnoodle

  I have a Shuttle Intel G31 + ICH7 (base -- not M/R etc) system. I just bought an OCZ Vertex 3 120gb [VTX3-25SAT3-120G] which includes the Sandforce 2218 firmware. The ICH7 does not support AHCI. I understand that this can be a problem. What I don't understand, is if it's necessary to have the proper performance of this drive. I know that without AHCI I may get a limited read/write speed -- this is fine. What my concern is, is the constant freezing/hangs I'm getting with Windows 7 on any disk activity. The 'Highest Active Time' flip-flops from 0 to 100% every minute or so regardless of large or small files. EDIT: The threads/processes with the highest response time is the kernel. I've been reading about other people with Shuttle SG31G2s, and they seem to be using SSDs no problem. Is this the controller's fault? The fact that I do not have AHCI enabled? It makes sense to me that if this SSD requires AHCI features that it would cause Windows to hang, but I would like to fully determine my situation before returning things/reformatting. To initially have my drive recognise the SSD at all, I had to change the BIOS option to Force Gen II instead of Auto for the SATA controller. I then installed Windows with no problem. There were no errors in the event log related to disk usage, but watching the perfmon I could see the highest active time and the processes (usually pagefile.sys being written to, or chrome/firefox caching) which was correlated to the hanging. So now what I need answered is: should I be returning this SSD and getting one with a different controller, or returning the SSD all-together as it will never work out and I will continue to get these hangs. Posts I've read: Windows 7 New SSD SATA AHCI? -- suggests to use AHCI http://forums.anandtech.com/showthread.php?t=2189868 -- Sandforce issues Windows 7 freezes with SSD -- and attached posts Why does my Windows 7 PC / SSD drive keep freezing? -- this is not the controller I have, but still a related issue. Windows 7 hangs after longer inactivity of user -- also tried messing with power settings with no luck. It was already set to 'Never' for turning off HDDs.

  Read the article

• Access denied to mysql cause by invalid server hostname bind address

  - by Mark

  I cannot login to mysql using the terminal. [root@fst mysql]# mysql -h localhost -u admin -p Enter password: ERROR 1045 (28000): Access denied for user 'admin'@'localhost' (using password: YES) I am sure I have the correct password. The mysql is also running when I check status. The mysql database is also present in the directory /var/lib/mysql/. The host host.myi, host.myd and host.frm are present. By the way this a related to question on my previous problem MySQL server quit without updating PID file . Initially the problem arise when the root directory was full. To be able to login to directadmin and start mysql, I added a soft link of the /var/lib/mysql/ to /home/mysql. Since my database used up the most of the root directory. The root directory has 50Gb and /home has 1.5Gb. Somehow the /var/lib/mysql/idbdata1 is corrupted. So I move it to another location. Now, I can start the mysql server but I cannot login into it. Below are the contents from the myql logs. 121212 20:44:10 mysqld_safe mysqld from pid file /var/lib/mysql/fst.srv.net.pid ended 121212 20:44:10 mysqld_safe Starting mysqld daemon with databases from /var/lib/mysql 121212 20:44:10 [Note] Plugin 'FEDERATED' is disabled. 121212 20:44:10 InnoDB: The InnoDB memory heap is disabled 121212 20:44:10 InnoDB: Mutexes and rw_locks use GCC atomic builtins 121212 20:44:10 InnoDB: Compressed tables use zlib 1.2.3 121212 20:44:10 InnoDB: Using Linux native AIO 121212 20:44:10 InnoDB: Initializing buffer pool, size = 128.0M 121212 20:44:10 InnoDB: Completed initialization of buffer pool 121212 20:44:10 InnoDB: highest supported file format is Barracuda. 121212 20:44:11 InnoDB: Waiting for the background threads to start 121212 20:44:12 InnoDB: 1.1.8 started; log sequence number 1595675 121212 20:44:12 [Note] Server hostname (bind-address): '0.0.0.0'; port: 3306 121212 20:44:12 [Note] - '0.0.0.0' resolves to '0.0.0.0'; 121212 20:44:12 [Note] Server socket created on IP: '0.0.0.0'. 121212 20:44:12 [Note] Event Scheduler: Loaded 0 events 121212 20:44:12 [Note] /usr/sbin/mysqld: ready for connections. Version: '5.5.27-log' socket: '/var/lib/mysql/mysql.sock' port: 3306 MySQL Community Server (GPL) I guess there is something wrong with the bind address. How should I fix the problem?

  Read the article

• Can't get Monit to work

  - by Andrea

  I am trying to configure Monit on my local machine to get a taste at how it works, but I have some issues. What I am trying to do is to get any evidence that Monit is up and running correctly and is actually monitoring something. So my /etc/monit/monitrc looks like set daemon 60 set logfile /var/log/monit.log set idfile /var/lib/monit/id set statefile /var/lib/monit/state set eventqueue basedir /var/lib/monit/events slots 100 set httpd port 2812 and allow username:password check process apache2 with pidfile /usr/local/apache/logs/apache2.pid start program = "/etc/init.d/apache2 start" stop program = "/etc/init.d/apache2 stop" if failed port 6543 protocol http then exec "/usr/bin/touch /tmp/monit" If I understand correctly, since apache does not listen on port 6543 (it is just a random number) I should get an error, and as a consequence the file /tmp/monit should be created. So I start monit by sudo service monit start sudo monit monitor apache2 Unfortunately no such file is created. Instead the web console shows an error for apache - execution failed. The log says 'apache2' failed to start. What am I doing wrong? EDIT As suggested in the comments, I ran monit in verbose mode, by monit -vv monitor apache2 (the exact command suggested in the comments failed). The output is Runtime constants: Control file = /etc/monit/monitrc Log file = /var/log/monit.log Pid file = /var/run/monit.pid Debug = True Log = True Use syslog = False Is Daemon = True Use process engine = True Poll time = 60 seconds with start delay 0 seconds Expect buffer = 256 bytes Event queue = base directory /var/lib/monit/events with 100 slots Mail from = (not defined) Mail subject = (not defined) Mail message = (not defined) Start monit httpd = True httpd bind address = Any/All httpd portnumber = 2812 httpd signature = True Use ssl encryption = False httpd auth. style = Basic Authentication The service list contains the following entries: Process Name = apache2 Pid file = /usr/local/apache/logs/apache2.pid Monitoring mode = active Start program = '/etc/init.d/apache2 start' timeout 30 second(s) Stop program = '/etc/init.d/apache2 stop' timeout 30 second(s) Existence = if does not exist 1 times within 1 cycle(s) then restart else if succeeded 1 times within 1 cycle(s) then alert Pid = if changed 1 times within 1 cycle(s) then alert Ppid = if changed 1 times within 1 cycle(s) then alert Port = if failed localhost:6543 [HTTP via TCP] with timeout 5 seconds 1 times within 1 cycle(s) then exec '/usr/bin/touch /tmp/prova-monit' timeout 0 cycle(s) else if succeeded 1 times within 1 cycle(s) then alert System Name = system_andrea-Vostro-420-Series Monitoring mode = active

  Read the article

• Windows 7 x64 "upgrade" repair fails

  - by Polynomial

  I've been running into issues with Windows Update, which I can't seem to fix. The hotfixes don't work, nor does the Windows update readyness tool, or the manual SP1 upgrade. I get various esoteric errors which nobody seems to have a fix for. Looks like some of the update cache is corrupt and digital signatures seem to be broken on some packages / Windows Update components. Long story short, I have discovered the only option is to do a repair operation on the OS, to repair everything. It's so corrupt that only a complete replacement will fix it. According to various sources (including MSKB) one can perform a repair by running an in-place upgrade. I've got the Windows 7 Ultimate retail disc, which I've inserted into my machine. I ran setup.exe and went through in the following order: Install now Go online to get latest updates (I've also tried not getting updates) Wait for updates to be downloaded Select Windows 7 Ultimate (x64 architecture) and click next Accept the T&Cs, click next Click Upgrade At this point it spends a minute on the "checking compatibility" screen, after which I get the following error: The following issues are preventing Windows from upgrading. Cancel the upgrade, complete each task, and then restart the upgrade to continue. You can’t upgrade 64-bit Windows to a 32-bit version of Windows. To upgrade, obtain a 64-bit version of the installation disc, or go online to see how to install Windows 7 and keep your files and settings. 32-bit Windows cannot be upgraded to a 64-bit version of Windows. To upgrade, obtain a 32-bit version of the Windows installation disc. It also mentions a warning about potential conflicts with a storage driver and VS2010, but that doesn't seem to be the blocking issue. My currently installed version of Windows is Ultimate 64-bit (absolutely sure of this) and the disc is definitely a x86 / x64 combined Ultimate retail disc. There seem to be a few people who have run into this (e.g. this question), but I've not seen any answers. I've checked the event viewer, but can't spot anything in there that's related. Any idea how I can get this working? P.S: Just to pre-empt the inevitable "are you suuuuuuuuuuuuure it's x64 Ultimate?" questions:

  Read the article

• Cliq Wireless questions

  - by Nathan Adams

  Heres the deal: I am by no means a Linux expert, even less when it comes to the Android OS but lets see if we can't solve this problem. The problem I am having is that on the Cliq we have a broadcom chip. In order to use the wireless card you must first insert the module into the kernel. Fine: # insmod /system/lib/dhd.ko insmod /system/lib/dhd.ko # lsmod lsmod dhd 164936 0 - Live 0xbf000000 # BUT netcfg (or ifconfig in busybox) does not recognize that there is a wireless adapter there: # netcfg netcfg lo UP 127.0.0.1 255.0.0.0 0x00000049 dummy0 DOWN 0.0.0.0 0.0.0.0 0x00000082 rmnet0 UP 14.67.164.2 255.255.255.252 0x00001043 rmnet1 DOWN 0.0.0.0 0.0.0.0 0x00001002 rmnet2 DOWN 0.0.0.0 0.0.0.0 0x00001002 usb0 DOWN 0.0.0.0 0.0.0.0 0x00001002 # busybox ifconfig busybox ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:282 errors:0 dropped:0 overruns:0 frame:0 TX packets:282 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:18754 (18.3 KiB) TX bytes:18754 (18.3 KiB) rmnet0 Link encap:Ethernet HWaddr EE:83:E8:B4:4A:ED inet addr:14.x.x.x Bcast:14.67.164.3 Mask:255.255.255.252 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:7148 errors:0 dropped:0 overruns:0 frame:0 TX packets:7659 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2609236 (2.4 MiB) TX bytes:908575 (887.2 KiB) # For giggles if we attempt to launch wpa_supplicant anyways we get this: # wpa_supplicant -Dwext -ieth0 -c/data/misc/wifi/wpa_supplicant.conf wpa_supplicant -Dwext -ieth0 -c/data/misc/wifi/wpa_supplicant.conf ioctl[SIOCSIWPMKSA]: No such device ioctl[SIOCSIWMODE]: No such device Could not configure driver to use managed mode ioctl[SIOCGIFFLAGS]: No such device Could not set interface 'eth0' UP ioctl[SIOCGIWRANGE]: No such device ioctl[SIOCGIFINDEX]: No such device CTRL-EVENT-STATE-CHANGE id=-1 state=0 ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWAUTH]: No such device WEXT auth param 7 value 0x0 - Failed to disable WPA in the driver. ioctl[SIOCSIWAUTH]: No such device WEXT auth param 5 value 0x0 - ioctl[SIOCSIWAUTH]: No such device WEXT auth param 4 value 0x0 - ioctl[SIOCSIWAP]: No such device ioctl[SIOCGIFFLAGS]: No such device # In dmesg we get: <4>[18300.494065] dhd_oob_enable_intr : enable <4>[18305.019976] dhd_net_start failed bus is not ready <4>[18305.020278] dhdsdio_probe: dhd_net_start failed! Do I need to specify the firmware with insmod? Why are we trying to control the interface manually instead of through the Android API? The Android API doesn't support ad-hoc connections as far as I can tell. The card, I am sure, most certainly can.

  Read the article

• Why are emails sent from my applications being marked as spam?

  - by Brian

  Hi. I have 2 web apps running on the same server. The first is www.nimikri.com and the other is www.hourjar.com. Both apps share the same IP address (75.127.100.175). My server is through a shared hosting company. I've been testing my apps, and at first all my emails were being delivered to me just fine. Then a few days ago every email from both apps got dumped into my spam box (in gmail and google apps). So far the apps have just been sending emails to me and nobody else, so I know people aren't manually flagging them as spam. I did a reverse DNS lookup for my IP and the results I got were these: 100.127.75.in-addr.arpa NS DNS2.GNAX.NET. 100.127.75.in-addr.arpa NS DNS1.GNAX.NET. Should the reverse DNS lookup point to nimikri.com and hourjar.com, or are they set up fine the way they are? I noticed in the email header these 2 lines: Received: from nimikri.nimikri.com From: Hour Jar <[email protected]> Would the different domain names be causing gmail to think this is spam? Here is the header from one of the emails. Please let me know if any of this looks like a red flag for spam. Thanks. Delivered-To: [email protected] Received: by 10.231.157.85 with SMTP id a21cs54749ibx; Sun, 25 Apr 2010 10:03:14 -0700 (PDT) Received: by 10.151.130.18 with SMTP id h18mr3056714ybn.186.1272214992196; Sun, 25 Apr 2010 10:03:12 -0700 (PDT) Return-Path: <[email protected]> Received: from nimikri.nimikri.com ([75.127.100.175]) by mx.google.com with ESMTP id 28si4358025gxk.44.2010.04.25.10.03.11; Sun, 25 Apr 2010 10:03:11 -0700 (PDT) Received-SPF: neutral (google.com: 75.127.100.175 is neither permitted nor denied by best guess record for domain of [email protected]) client-ip=75.127.100.175; Authentication-Results: mx.google.com; spf=neutral (google.com: 75.127.100.175 is neither permitted nor denied by best guess record for domain of [email protected]) [email protected] Received: from nimikri.nimikri.com (localhost.localdomain [127.0.0.1]) by nimikri.nimikri.com (8.14.3/8.14.3) with ESMTP id o3PH3A7a029986 for <[email protected]>; Sun, 25 Apr 2010 12:03:11 -0500 Date: Sun, 25 Apr 2010 12:03:10 -0500 From: Hour Jar <[email protected]> To: [email protected] Message-ID: <[email protected]> Subject: [email protected] has invited you to New Event MIME-Version: 1.0 Content-Type: text/html; charset=us-ascii Content-Transfer-Encoding: 7bit

  Read the article

• !! 0xc01a00d !! aka Vista won't boot

  - by Chris

  Answer: Parts of the hard drive are corrupted. All of my user's code was checked in, so I'm just going to format the box. One of my users has an HP DV5-1235dx laptop running Windows Vista Professional x64. Last night, our WSUS server pushed out a few updates including "Security Update for Windows Vista for x64-based Systems (KB960859)". When we try to boot the laptop today, a black screen with white text comes up displaying: xxx/169894 (something) Where xxx increments rapidly and something is some dll or registry key. Eventually that stops and the screen displays !! 0xc01a00d !! 35566/169894 (\Registry\Machine\COMPONENTS\DerivedDat...) No other computers that received this update are displaying the same error. So far I've tried running CHKDSK off of HBCD. It repaired a thing or two, but the computer still doesn't boot. I tried repairing the Windows install from the Vista CD, but I get a black screen with white text displaying something along the lines of: 0 No Emulation System Type 00 1 No Emulation System Type 00 Select one of the above Booting in Last Known Good Configuration doesn't work. Booting in Safe Mode freezes at Loading Windows Files [snip] Loaded: \windows\system32\drivers\crcdisk.sys Please wait... My next step is trying to boot Safe Mode with Command Prompt and try to run rstrui.exe. While I do that, does anybody have any guidance? Edit: Booting into Safe Mode with Command Prompt will not work. See Booting in Safe Mode above. Edit 2: I managed to boot from the Vista DVD. I ran the system repair, and now I get a black screen with white text saying: !! 0xc0000034 !! 290/169894 (_0000000000000000.cdf-ms) Edit 3: I ran the system repair again, and it attempted to repair my hard drive. It failed. Problem Signature: Problem Event Name: Startup Repair V2 Problem Signature 01: External Media Problem Signature 02: 6.0.6001.18000.6.0.6001.18000 Problem Signature 03: 4 Problem Signature 04: 196611 Problem Signature 05: CorruptVolume Problem Signature 06: NoBootFailure Problem Signature 07: 0 Problem Signature 08: 0 Problem Signature 09: unknown Problem Signature 10: 1168 OS Version: 6.0.6002.2.2.0.256.1 Locale ID: 1033 Answer: Parts of the hard drive are corrupted. All of my user's code was checked in, so I'm just going to format the box.

  Read the article

• SSH: Connection Reset by Peer

  - by hopeless

  I have a Solaris 10 server on another network. I can ping it and telnet to it, but ssh doesn't connect. PuTTY log contains nothing of interest (they both negotiate to ssh v2) and then I get "Event Log: Network error: Software caused connection abort". ssh is defintely running: svcs -a | grep ssh online 12:12:04 svc:/network/ssh:default Here's an extract from the server's /var/adm/messages (anonymised) Jun 8 19:51:05 ******* sshd[26391]: [ID 800047 auth.crit] fatal: Read from socket failed: Connection reset by peer However, if I telnet to the box, I can login to ssh locally. I can also ssh to other (non-Solaris) machines on that network fine so I don't believe that it's a network issue (though, since I'm a few hundred miles away, I can't be sure). The server's firewall is disabled, so that shouldn't be a problem root@******** # svcs -a | grep -i ipf disabled Apr_27 svc:/network/ipfilter:default Any ideas what I should start checking? Update: Based on the feedback below, I've run sshd in debug mode. Here's the client output: $ ssh -vvv root@machine -p 32222 OpenSSH_5.0p1, OpenSSL 0.9.8h 28 May 2008 debug2: ssh_connect: needpriv 0 debug1: Connecting to machine [X.X.X.X] port 32222. debug1: Connection established. debug1: identity file /home/lawrencj/.ssh/identity type -1 debug1: identity file /home/lawrencj/.ssh/id_rsa type -1 debug1: identity file /home/lawrencj/.ssh/id_dsa type -1 debug1: Remote protocol version 2.0, remote software version Sun_SSH_1.1 debug1: no match: Sun_SSH_1.1 debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.0 debug2: fd 3 setting O_NONBLOCK debug1: SSH2_MSG_KEXINIT sent Read from socket failed: Connection reset by peer And here's the server output: root@machine # /usr/lib/ssh/sshd -d -p 32222 debug1: sshd version Sun_SSH_1.1 debug1: read PEM private key done: type RSA debug1: private host key: #0 type 1 RSA debug1: read PEM private key done: type DSA debug1: private host key: #1 type 2 DSA debug1: Bind to port 32222 on ::. Server listening on :: port 32222. debug1: Bind to port 32222 on 0.0.0.0. Server listening on 0.0.0.0 port 32222. debug1: Server will not fork when running in debugging mode. Connection from 1.2.3.4 port 2652 debug1: Client protocol version 2.0; client software version OpenSSH_5.0 debug1: match: OpenSSH_5.0 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-Sun_SSH_1.1 debug1: list_hostkey_types: ssh-rsa,ssh-dss debug1: Failed to acquire GSS-API credentials for any mechanisms (No credentials were supplied, or the credentials were unavailable or inaccessible Unknown code 0 ) debug1: SSH2_MSG_KEXINIT sent Read from socket failed: Connection reset by peer debug1: Calling cleanup 0x4584c(0x0) This line seems a likely candidate: debug1: Failed to acquire GSS-API credentials for any mechanisms (No credentials were supplied, or the credentials were unavailable or inaccessible

  Read the article

• CentOS 6 - Make system aware of custom lib paths and missing base links

  - by Mike Purcell

  I am trying to compile libmemcached (1.0.7) on CentOS6, and keep getting the following warning: ... checking for event.h... no configure: WARNING: Unable to find libevent ... I manually compiled libevent (2.0.19) and built it using the following configure line: OPTIONS="--prefix=/usr/local/_custom/app/libevent" Everything compiled and installed fine, but I couldn't figure out how to make the system aware that the lib files are in the custom /usr/local/_custom/app/libevent/libdir. I stumbled upon an article and read that I can make the system aware of custom lib paths by adding a custom file to /etc/ld.so.conf.d/ directory: # /etc/ld.so.conf.d/customApp.conf /usr/local/_custom/app/libevent/lib Then I issued the ldconfig command and was able to confirm that libevent was included by issuing this command: ldconfig -p | ack -i libevent Seeing that libevent was now included in the ldconfig output, I figured I would be able to compile libmemcached and satisfy the aforementioned warning. Unfortunately it did not. So I took another look at the ldconfig output and noticed this: libevent_pthreads-2.0.so.5 (libc6,x86-64) => /usr/local/_custom/app/libevent/lib/libevent_pthreads-2.0.so.5 libevent_openssl-2.0.so.5 (libc6,x86-64) => /usr/local/_custom/app/libevent/lib/libevent_openssl-2.0.so.5 libevent_extra-2.0.so.5 (libc6,x86-64) => /usr/local/_custom/app/libevent/lib/libevent_extra-2.0.so.5 libevent_core-2.0.so.5 (libc6,x86-64) => /usr/local/_custom/app/libevent/lib/libevent_core-2.0.so.5 libevent-2.0.so.5 (libc6,x86-64) => /usr/local/_custom/app/libevent/lib/libevent-2.0.so.5 There are no references to the base links, for example, I would expect to see links to these (ls -la /usr/local/_custom/app/libevent/lib): libevent.so -> libevent-2.0.so.5.1.7 libevent_openssl.so -> libevent_openssl-2.0.so.5.1.7 libevent_core.so -> libevent_core-2.0.so.5.1.7 So either I am doing something wrong, or the system still does not know where to look to find libevent.so. -- Update #1 -- I wasn't able to get libmemcached to compile without the warning notice, even after trying to compile using the following configure command: ./configure --prefix=/usr/local/_custom/app/libmemcached CFLAGS="-I/usr/local/_custom/app/libevent/include" LDFLAGS="-L/usr/local/_custom/app/libevent/lib" I thought for sure this would work because I am directly passing the include and lib directories to the configure command. But it did not.

  Read the article

• Safer RAID5 rebuilds using partially failed disks?

  - by arcticmac

  There have been lots of articles posted recently about how RAID5 is dangerous because of long resilver times, and in particular because of increasing chances of encountering a URE during the resilver. Obviously this is a significant concern. However, it seems that in many cases of interest (as long as you're keeping some kind of eye on your disks), when it comes time to rebuild the array, the disk that I'm replacing is still mostly readable. If you try to explain this predicament to the average layperson, they are typically very confused as to why you have two almost completely functional disks but can't produce one working array. It seems to me that there ought to be some way to take advantage of this to make rebuilds safer, as long as I'm willing to have the RAID5 be read-only for a couple of days while it rebuilds. Conceptually, what I have in mind looks something like this: When a disk fails, immediately take the RAID5 offline or mount it read-only Attach a new disk (either in a spare bay, or externally via eSATA) and begin rebuilding it to replace the failed one. If known, perhaps start with the stripes in which the failure occurred, to minimize the chances of losing those if another disk fails. In the event that a second disk experiences a URE or other failure during the rebuild, try to source that data from the disk that is being replaced. Presumably if this happens, more rebuilding would be necessary. When complete, shut down the server, swap the replacement drive into the original bay if desired, and bring the array back up. Obviously such a process would not be appropriate for applications where uptime is critical or data loss cannot be tolerated, but it seems to me that this could help considerably to improve the reliability of RAID5. I assume that there's not a good way to implement a recovery like this at present, given that I haven't seen any indication of tools that are designed to do this, and that it seems like it would be rather obtuse to work out manually. Are there also technical issues with it that I haven't thought of (I'm still fairly new to RAID stuff)? Any thoughts on how hard something like this would be to implement (e.g. in linux md raid)?

  Read the article

• WinXP - Having trouble sharing internet with 3G USB modem via ICS

  - by Carlos Nunez

  all! I've been banging my head against a wall with this issue for a few days now and am hoping someone can help out. I recently signed up for T-Mobile's webConnect 3G/4G service to replace the faltering (and slow) DSL connection in my apartment. The goal was to put the SIM in one of my old phones and use its built-in WLAN tethering feature to share Internet out to rest of my computers. I quickly found out that webConnect-provisioned SIMs do not work with regular smartphones, so I was forced to either buy a 4G-compatible router or tether one of my old laptops to my wireless router and share out that way. I chose the latter, and it's sharpening my inner masochistic self by the day. Here's the setup: GSM USB modem (via hub), ICS host - 10/100 Mbps Ethernet NIC, ICS "guest" - WAN port of my SMC WGBR14N wireless router in bridged mode (i.e. wireless access point). Ideally, this would make my laptop the DHCP server and internet gateway with the WAP giving everyone wireless coverage. I can browse internet on the host laptop fine. However, when clients try to connect, they get a DHCP-assigned IP from the laptop and are able to use the Internet for a few minutes before completely dying. After that happens, they are able to re-associate with the WAP and get IP addresses, but are unable to use Internet or resolve IP addresses until the laptop and router are restarted. If they do get access, it's very, very slow. After running Wireshark on the host machine, it turns out that this is because every TCP connection keeps getting RST. DNS seems to work. I would normally think the firewall is the culprit here, but when it drops packets, it drops them completely. The fact that TCP connections are being ACK'ed by the destination rules that out. Of course, none of the event Log isn't saying anything about what's going on. I also tried disabling power management on the NIC, since that's caused problems in the past; that didn't help either. I finally disabled receive-side scaling as per a Microsoft KB (that applied to Windows Server 2003, SP2) to no avail. I'm thinking of trying it with a different NIC (will be tough; don't have a spare Ethernet NIC around for the laptop), but I'm getting the impression that this simply doesn't work. Can anyone please advise? I apologise for the length of this post; all contributions are much appreciated! -Carlos.

  Read the article

• Forms authentication failed between web server and sql server

  - by Matt Bear

  I've actually found the solution, but I'm trying to understand why it failed, and why my solution fixed the problem. We have an application that uses forms authentication between a web server and sql server, web server runs server 2008, sql server runs 2008 r2, and sql server 2008. In august the sql server was patched with .net 3.5.1, the web server was untouched, and the forms authentication continued to work. 1 week ago we virtualized the web server onto our vSphere server because of failing hardware. Afterwards the form authentication failed with event code 4005, detail code 50201, The ticket supplied was invalid (on the sql server). In fact the sql server started generating Schannel errors and began blue screening 3-4 times a day. At this point I touched the sql server for the first time(ever), the errors were non specific, any reference to them I could find had to do with either zone alarm(which we don't run), or memory errors. So I applied service pack 1, which stopped the blue screening, but did not fix the forms authentication. At this point we had a work around, so we put it on the back burner while we completed another project, and I was able to get back on it last night. First thing was to adjust some code in the webconfig file on the sql server, nothing, next was regenerate and change out the machine key, still no change. Update the DNS servers, no change. Finally I went through and installed all windows updates, two reboots, (over RDP installed a network card driver which failed, and did not have my server room key, that was fun). After that, forms authentication was working again. And the sql server stopped generating as many errors, I've gotten two schannel errors since then. In short, forms authentication began failing when the web server was cloned onto a virtual machine, which caused the sql server to blue sceen? and forms authentication to fail. And could only be fixed by applying patches to the sql server?(I'm wishing I had patched the servers one at a time so I could know for sure which patch on which server fixed it). My question is why did it fail, and why did patching fix it? I hate fixing something without fully understanding the why and how.

  Read the article

• SSD Fresh Does Not Start

  - by Jim Fell

  I recently installed a new 60GB SSD as my primary hard drive and re-installed Windows 7 Professional 64-bit. I then installed SSD Fress from Abelssoft to optimize Windows to run on the SSD. It seemed to install okay, but when I try to run the utility, its splash screen appears briefly before it quietly closes. No errors are displayed; the utility just fails to launch. I have run SSD Fresh on another SSD-equipped Windows 7 Pro x64 computer in the past without any problems. Does anyone know what might be preventing the program from running? I tried shutting down the Spybot Resident and disabling the firewall and virus scanner with no luck. I also tried running the tool as administrator; I even tried reinstalling it, running the installer as administrator. No luck. Every time I try to launch the program the Event Viewer logs this same set of errors: Error 4/2/2012 11:35:44 PM Application Error 1000 (100) Error 4/2/2012 11:35:43 PM .NET Runtime 1026 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None For those who are interested, here is my system configuration: ASRock M3A770DE AM3 AMD 770 ATX AMD Motherboard AMD Athlon II X3 455 Rana 3.3GHz Socket AM3 95W Triple-Core Desktop Processor ADX455WFGMBOX G.SKILL Value Series 8GB (2 x 4GB) 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10600) Desktop Memory Model F3-10600CL9D-8GBNT Mushkin Enhanced Chronos Deluxe MKNSSDCR60GB-DX 2.5" 60GB SATA III Synchronous MLC Internal Solid State Drive (SSD) (Primary/Boot HD) Western Digital Caviar Blue RFHWD1600AAJS 160GB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive -Bare Drive (Secondary HD) Sony Optiarc CD/DVD Burner Black SATA Model AD-7261S-0B LightScribe Support RAIDMAX RX-850AE 850W ATX12V v2.3 / EPS12V SLI Certified CrossFire Ready 80 PLUS GOLD Certified Modular Active PFC Power Supply ASUS HD7850-DC2-2GD5 Radeon HD 7850 2GB 256-bit GDDR5 PCI Express 3.0 x16 HDCP Ready CrossFireX Support Video Card Asus ML228H 21.5" Full HD LED BackLight LED Monitor Slim Design (x3)

  Read the article

• 401 - Unauthorized On Server 2008 R2 IIS 7.5

  - by mxmissile

  I have a web application deployed to Server 2008 IIS 7.5 box. From remote it gives this error: 401 - Unauthorized: Access is denied due to invalid credentials. (remote = desktops on the same LAN) Have tried several remote clients using different browsers, all the same result. (IE, FF, and Chrome) Hitting the application from the desktop of the server itself works flawlessly. However I have not tried Firebug on the server desktop. I would assume it's still issuing a 401 status code yet returning the content anyway. See Update #2. The application is using Anonymous Authentication. The application is written in .NET 4.0 Asp.Net using the MVC framework. Static content works fine, example: http://server.com/content/image.jpg Sysinternals procmon returns these 2 results for each request: FAST IO DISALLOWED and PATH NOT FOUND. I have 2 other MVC apps running fine on the same server. I have checked the security on the folders and they all match. App runs fine on a Server 2008 IIS 7.0 box. Nothing shows up in the Event log on the server related to this. Pulling my hair out here, any troubleshooting tips? UPDATE #1: This just get's more WTF as I dig. If I click on the Application in IIS Manager - Error Pages - Edit Feature Settings select Detailed Errors, the app works remotely. Not leaving this on, so problem is not solved yet, its just more confusing. UPDATE #2: Using Firebug, I see that the Status is still 401 Unauthorized, but the Response is returning the application's correct HTML. UPDATE #3 Playing around with Failed Request Tracing, here is the WARNING Request Trace that is causing the 401: ModuleName ManagedPipelineHandler Notification 128 HttpStatus 401 HttpReason Unauthorized HttpSubStatus 0 ErrorCode 0 ConfigExceptionInfo Notification EXECUTE_REQUEST_HANDLER ErrorCode The operation completed successfully. (0x0) Update #4 Regular IIS log is showing this: #Software: Microsoft Internet Information Services 7.5 #Version: 1.0 #Date: 2010-07-20 19:17:22 #Fields: date time s-ip cs-method cs-uri-stem cs-uri-query s-port cs-username c-ip cs(User-Agent) sc-status sc-substatus sc-win32-status time-taken 2010-07-20 19:17:22 10.10.1.10 GET /Purchasing/Home - 80 - 10.10.1.12 Mozilla/5.0+(Windows;+U;+Windows+NT+6.1;+en-US;+rv:1.9.2.6)+Gecko/20100625+Firefox/3.6.6 401 0 0 4414

  Read the article

• Hyper-V Machine drifts time all over, even with NTP

  - by MichaelGG

  Resolved The problem was Hyper-V on that machine. I removed Hyper-V, installed VMware Server, ran the same VM. Time sync issues went away (< 100ms difference after a day). My setup is like this: HYV1 - HyperV machine (non domain) - sync irrelevant AD1 - VM AD server on HYV1, sync'd to time.nist.gov. HyperV time sync off. S1 - Physical machine, sync'd to domain. S2 - Physical machine running HyperV, sync'd to domain. V1 - Linux VM machine on S2, sync'd to AD1. No HyperV integration. AD1 and S1 have fine sync -- stripchart shows less than 100ms difference. S2 drifts like crazy. Here's a bit of the stripchart against AD1: 18:33:22 d:+00.0010138s o:+05.4101899s 18:33:24 d:+00.0010138s o:+05.4319765s 18:33:26 d:+00.0000000s o:+05.4788429s 18:33:28 d:+00.0000000s o:+05.6089942s 18:33:30 d:+00.0010138s o:+05.7240269s 18:33:32 d:+00.0000000s o:+06.0421911s 18:33:34 d:+00.0081104s o:+06.5613708s 18:33:37 d:+00.0000000s o:+06.9096594s 18:33:39 d:+00.0000000s o:+06.8867838s 18:33:41 d:+00.0010127s o:+06.8936401s In 20 seconds, it drifted over a second. If I manually reset it to within 1s, within a few minutes it'll be back drifting about 2 seconds. Overnight it went from ~2s to ~5s. The Linux VM inside S2 has perfect sync with AD1. Here's the config: C:\Users\mgg>w32tm /dumpreg /subkey:Parameters Value Name Value Type Value Data ------------------------------------------------------------ ServiceDll REG_EXPAND_SZ %systemroot%\system32\w32time.dll ServiceMain REG_SZ SvchostEntry_W32Time ServiceDllUnloadOnStop REG_DWORD 1 Type REG_SZ NT5DS NtpServer REG_SZ ad01.mydomain ad02.mydomain C:\Users\mgg>w32tm /dumpreg /subkey:Config Value Name Value Type Value Data ----------------------------------------------------------- FrequencyCorrectRate REG_DWORD 4 PollAdjustFactor REG_DWORD 5 LargePhaseOffset REG_DWORD 50000000 SpikeWatchPeriod REG_DWORD 900 LocalClockDispersion REG_DWORD 9 HoldPeriod REG_DWORD 5 PhaseCorrectRate REG_DWORD 1 UpdateInterval REG_DWORD 30000 EventLogFlags REG_DWORD 2 AnnounceFlags REG_DWORD 5 TimeJumpAuditOffset REG_DWORD 28800 MinPollInterval REG_DWORD 2 MaxPollInterval REG_DWORD 8 MaxNegPhaseCorrection REG_DWORD -1 MaxPosPhaseCorrection REG_DWORD -1 MaxAllowedPhaseOffset REG_DWORD 300 I looked at the event log, and apart from warnings about sync (after it gets way out of sync), there's no other warnings. How can I go about troubleshooting this? It's the only machine that is having this problem. All the other machines (physical and virtual) are doing fine. Edit: To clarify: The VM (AD1) has integration turned off and syncs to time.nist.gov. AD1 is fine. It's the physical machine S1 that can't sync to AD1 and drifts all over. All the other physical servers are able to sync to AD1 just fine. Update So, it appears to be an issue of running the VM. The clock slips slowly with the VM off. Turned on, it immediately starts losing seconds. I swt the VM to only use half the resources, and that seems to have slightly mitigated it, for now. Thanks!

  Read the article

• Skyrim: Heavy Performance Issues after a couple of location changes

  - by Derija

  Okay, I've tried different solutions: ENB Series, removing certain mods, checking my FPS Rate, monitoring my resources, .ini tweaks. It's all just fine, I don't see what I'm missing. A couple of days ago, I bought Skyrim. Before I bought the game, I admit I had a pirated copy because my girlfriend actually wanted to buy me the game as a present, then said she didn't have enough money. Sick of waiting, I decided to buy the game by myself. The ridiculous part is, it worked better cracked than it does now uncracked. As the title suggests, after entering and leaving houses a couple of times, my performance obviously drops extremely. My build is just fine, Intel i5 quad core processor, NVIDIA GTX 560 Ti from Gigabyte, actually stock-OC, but manually downclocked to usual settings using appropriate Gigabyte software. This fixed the CTD issues I had before with both Skyrim and BF3. I have 4GB RAM. A website about Game Tweaks suggested that my HDD may be too slow. A screenshot of a Windows Performance Index sample with the subscription "This is likely to cause issues" showed the HDD with a performance index of 5.9, the exact same mine has, so I was playing with the thought to purchase an SSD instead, load games onto it that really need it like Skyrim, and hope it'd do the trick. Unfortunately, SSDs are likewise expensive, compared to "normal" HDDs... I'm really getting desperate about it. My save is gone because the patches made it impossible to load saves of the unpatched version and I already saved more than 80 times despite being only level 8, just because every time I interact with a door leading me to another location I'm scared the game will drop again. I can't even play for 30 mins straight anymore, it's just no fun at all. I've researched for a couple of days before I decided to post my question here. Any help is appreciated, I don't want to regret having bought the game... Since it actually is the best game I've played possibly for ever. Sincerely. P.S.: I don't think it's necessary to say, but still, of course I'm playing on PC. P.P.S.: After monitoring both my PC resources including CPU usage and HDD usage as well as the GPU usage, I don't see any changes even after the said event. P.P.P.S.: Original question posted here where I've been advised to ask here.

  Read the article

• Moving from single-site to multi-site Active Directory has broken OWA proxying

  - by messick

  Originally we had the following setup: OfficeExch01 has Mailbox Role and CAS Role OfficeExch01 is in the office. CoLoExch01 had just CAS Role. CoLoExch01 is internet facing and in a CoLo. Three AD domain controllers in the default site. Users could go to https://webmail.whatever.com/owa, get proxyed to OfficeExch01 and everything was great. Well, we recently setup a separate AD site and put a domain controller and the ColoExch01 server in the new site. I also made that remote DC be a Global Catalog. Now, users get the following error: Outlook Web Access is not available. If the problem continues, contact technical support for your organization and tell them the following: There is no Microsoft Exchange Client Access server that has the necessary configuration in the Active Directory site where the mailbox is stored. I also see event 41 errors in the logs: The Client Access server "https://webmail.xxxxxxx.com/owa" attempted to proxy Outlook Web Access traffic for mailbox "/o=XXXXX/ou=Exchange Administrative Group (FYDIBOHF23SPDLT)/cn=Recipients/cn=xxxxxxk". This failed because no Client Access server with an Outlook Web Access virtual directory configured for Kerberos authentication could be found in the Active Directory site of the mailbox. The simplest way to configure an Outlook Web Access virtual directory for Kerberos authentication is to set it to use Integrated Windows authentication by using the Set-OwaVirtualDirectory cmdlet in the Exchange Management Shell, or by using the Exchange Management Console. If you already have a Client Access server deployed in the target Active Directory site with an Outlook Web Access virtual directory configured for Kerberos authentication, the proxying Client Access server may not be finding that target Client Access server because it does not have an internalUrl parameter configured. You can configure the internalUrl parameter for the Outlook Web Access virtual directory on the Client Access server in the target Active Directory site by using the Set-OwaVirtualDirectory cmdlet. Looking this up I see a lot talk about ExternalURL and InternalURL settings. However, everything worked great until we made the new AD site. I also made sure the internal CAS server's /owa virtual directory is set to use Integrated Authentication. Is there something I need to do to allow Exchange to see that I've made these AD changes?

  Read the article

• Backing Up vs. Redundancy

  - by TK Kocheran

  I'm currently in stage 2 of 3 of building my home workstation. What this means is that my RAID-0 array of solid state disks will be backed up nightly to a RAID-5 or RAID-6 array of traditional spinning hard disks. However, it recently dawned on me that redundancy is not backup. The main reason for setting up a RAID array with redundancy was to protect myself in the event of a drive failure to serve as an effective backup solution. Wait. What if a bolt of lightning finds a way to travel into my house, through my surge-protector, into my power supply and physically destroys all of my hard disks and SSDs? Well, in that case, I guess I'd be fine because I generally keep most important files (music, pictures, videos) stored in multiple places like on my laptop, my wife's laptop, and an encrypted USB hard drive. Wait. What if a giant hedgehog meteor attacks my house from space traveling at mach 3 and all machines and hard disks are blown to smithereens. Well, I guess I could find a way to do ridiculously slow and cumbersome rsyncs or backups to Amazon's Glacier. Wait. What if there's a nuclear apocalypse... and at this point I start laughing hysterically. At what point does backing up become irrelevant? I completely understand situation one (mechanical drive failure), situation two (workstation compromised or destroyed somehow), possibly even situation three (all machines and disks destroyed), but situation four? There's no questioning the need for backups. None. However, there are three questions I'd really like addressed: To what level should one backup? I definitely understand the merits of physical disk redundancy. I also believe in keeping important files on multiple machines and thinning out the possibility of losing all of my files. Online backups make sense, but they beg the following question. What should I be backing up remotely and how often? It's no problem storage-wise to back up important files (music, pictures, videos) and even configuration and temporal data for all of the machines in my network (all Linux based)... albeit locally. Transferring to the cloud is another story. Worst-case scenario, if I lost all of my configuration for my individual computers, the reality is that I probably lost the machines too. The cloud is a long way away from here; I can run backups over CAT-6 here and see 100MB/s easily, but I'm afraid that I'm only going to see 2MB/s at best when transferring up to the cloud.

  Read the article

• Why is my new Phenom II 965 BE not significantly faster than my old Athlon 64 X2 4600+?

  - by Software Monkey

  I recently rebuilt my 5 year old computer. I upgraded all core components, in particular from an Athlon 64 X2 4600+ at 2.4 GHz with DDR2 800 to a Phenom II 965 BE (quad core) at 3.6 GHz with DDR3 1333 (actually 1600, but testing consistently detected memory errors at 1600). The motherboard is also much newer and better. The HDD's (x3), DVD writer and card reader are the same. The BIOS memory config is auto-everything except the base timing which I overrode to 1T instead of 2T. The BIOS CPU multiplier is slightly over-clocked to 3.6 GHz from the stock 3.4 GHz. I noticed compiling Java is slower than I expected. As it happens I have some (single-threaded) Java pattern-matching code which is CPU and memory bound and for which I have performance numbers recorded on a number of hardware platforms, including my old system. So I did a test run on the new equipment and was stunned to find that the numbers are only slightly better than my old system, about 25%. The data set it is operating on is a 148,975 character array, which should easily fit in caches, but in any event the new CPU has larger caches all around. The system was, of course, otherwise idle for the test and the test run is a timed 10 seconds to eliminate scheduling anomalies. A long while ago, when I upgraded only memory from DD2 667 to DDR2 800 there was no change in performance of this test, which subjectively supports that the test cycle does not need to (significantly) access main memory, but yes it is creating and garbage collecting a large number of objects in the process of this test (low millions of matches are found for the pattern set). I am about 99.999% certain the code hasn't changed since I last ran it on 2009-03-17 - but I can't easily retest the old hardware, because it is currently in pieces on my work-bench waiting to be built into a new computer for my kids. Note that Windows (XP) reports a CPU speed of 795 MHz unless I have some thing running. With stuff running it seems to jump all over the place each time I use ALT-Pause to display the system properties, everywhere from 795 MHz to 3.4 Ghz. So why might my shiny new hardware under-performing so badly? EDIT: The old memory was Mushkin DDR2 800 with timings set for auto which should have been 5-5-5-12. The new memory is Corsair DDR3 1600, running at 1333 with timings also auto which are 9-9-9-21. In both cases they are a paired set of dual channel DIMMs. I was waiting to ensure my system was stable before tweaking with memory timings.

  Read the article

• Write STDOUT & STDERR to a logfile, also write STDERR to screen

  - by Stefan Lasiewski

  I would like to run several commands, and capture all output to a logfile. I also want to print any errors to the screen (or optionally mail the output to someone). Here's an example. The following command will run three commands, and will write all output (STDOUT and STDERR) into a single logfile. { command1 && command2 && command3 ; } > logfile.log 2>&1 Here is what I want to do with the output of these commands: STDERR and STDOUT for all commands goes to a logfile, in case I need it later--- I usually won't look in here unless there are problems. Print STDERR to the screen (or optionally, pipe to /bin/mail), so that any error stands out and doesn't get ignored. It would be nice if the return codes were still usable, so that I could do some error handling. Maybe I want to send email if there was an error, like this: { command1 && command2 && command3 ; } logfile.log 2&1 || mailx -s "There was an error" [email protected] The problem I run into is that STDERR loses context during I/O redirection. A '2&1' will convert STDERR into STDOUT, and therefore I cannot view errors if I do 2 error.log Here are a couple juicier examples. Let's pretend that I am running some familiar build commands, but I don't want the entire build to stop just because of one error so I use the '--keep-going' flag. { ./configure && make --keep-going && make install ; } > build.log 2>&1 Or, here's a simple (And perhaps sloppy) build and deploy script, which will keep going in the event of an error. { ./configure && make --keep-going && make install && rsync -av --keep-going /foo devhost:/foo} > build-and-deploy.log 2>&1 I think what I want involves some sort of Bash I/O Redirection, but I can't figure this out.

  Read the article

• System Requirements of a write-heavy applications serving hundreds of requests per second

  - by Rolando Cruz

  NOTE: I am a self-taught PHP developer who has little to none experience managing web and database servers. I am about to write a web-based attendance system for a very large userbase. I expect around 1000 to 1500 users logged-in at the same time making at least 1 request every 10 seconds or so for a span of 30 minutes a day, 3 times a week. So it's more or less 100 requests per second, or at the very worst 1000 requests in a second (average of 16 concurrent requests? But it could be higher given the short timeframe that users will make these requests. crosses fingers to avoid 100 concurrent requests). I expect two types of transactions, a local (not referring to a local network) and a foreign transaction. local transactions basically download userdata in their locality and cache it for 1 - 2 weeks. Attendance equests will probably be two numeric strings only: userid and eventid. foreign transactions are for attendance of those do not belong in the current locality. This will pass in the following data instead: (numeric) locality_id, (string) full_name. Both requests are done in Ajax so no HTML data included, only JSON. Both type of requests expect at the very least a single numeric response from the server. I think there will be a 50-50 split on the frequency of local and foreign transactions, but there's only a few bytes of difference anyways in the sizes of these transactions. As of this moment the userid may only reach 6 digits and eventid are 4 to 5-digit integers too. I expect my users table to have at least 400k rows, and the event table to have as many as 10k rows, a locality table with at least 1500 rows, and my main attendance table to increase by 400k rows (based on the number of users in the users table) a day for 3 days a week (1.2M rows a week). For me, this sounds big. But is this really that big? Or can this be handled by a single server (not sure about the server specs yet since I'll probably avail of a VPS from ServInt or others)? I tried to read on multiple server setups Heatbeat, DRBD, master-slave setups. But I wonder if they're really necessary. the users table will add around 500 1k rows a week. If this can't be handled by a single server, then if I am to choose a MySQL replication topology, what would be the best setup for this case? Sorry, if I sound vague or the question is too wide. I just don't know what to ask or what do you want to know at this point.

  Read the article

• External USB HD issues with a twist (works on Windows7 but not XP)

  - by Eruditass

  I have this older external USB HD, 160 GB. I was using it to copy my Steam games to another computer. On the source computer, Windows 7 64-bit, everything worked fine. Drive reported no errors, had no hiccups, etc. Plugging it into the Windows XP 32-bit computer, it worked fine for looking through the files, moving files around on it (no real reading/writing, just modifying the filesystem table). However, when copying files from it to my internal HD, after a couple seconds to tens of minutes (seemingly random times), the USB device becomes unrecognized and it reports a delayed write error. Events in system log go like this, chronologically: (number times displayed)xSource (Event ID): "message" 2xdisk (51): An error was detected on device \Device\Harddisk1\D during a paging operation. 1xftdisk (57): The system failed to flush data to the transaction log. Corruption may occur. 1xApplication popup (26): Windows - Delayed Write Failed : Windows was unable to save all the data for the file E:\$Mft. The data has been lost. This error may be caused by a failure of your computer hardware or network connection. Please try to save this file elsewhere. 1xntfs (50): {Delayed Write Failed} Windows was unable to save all the data for the file . The data has been lost. This error may be caused by a failure of your computer hardware or network connection. Please try to save this file elsewhere. These repeat for a while, then there is 10+ disk messages or ftdisk messages. Other notes: This occurs on random files at random times. This problem cannot be replicated on the Windows 7 source machine when copying from the HD to a different location on its local disk chkdsk /f was run and found no errors. chkdsk /f/r has the delayed write issue. drive was set to quick removal. Setting to performance in device manager yielded same result I am not writing anything to the USB external drive, so I am not sure why there is even a delayed write error (writing file access times?) local Windows XP was chkdsk'd without problems Windows XP machine has no problems with other USB HD's Various USB ports were attempted Rebooting did not help Occurs with SyncToy as well as windows explorer SMART status is good on both local drive and the external one Lack of gaming is making me cranky

  Read the article

• APC ups es 700 randomly overload

  - by Matteo Mosca

  First of all, I live in Italy, Europe, so keep this in mind for Volt/Watt considerations. Standard voltage in Italian apartments is 220V. In my living room I have 2 APC ups, one being an ES-550 and the other an ES-700 They each have 4 slots for surge protection only, and 4 slots for surge protection + battery backup. Just to give all the information, they both got their battery replaced less than one month ago. The ES-550 works fine, without any problem. On the battery I have connected: Pc Monitor Sony Bravia 46'' 4th slot is empty The ES-700 has the following on battery: Xbox 360 Ps3 (standby when not used) Wii (standby when not used) Netgear 8 port switch (always on) Here's what happens: the ES-700, randomly, but mostly at night when I'm sleeping, goes like "overload", with the constant beep. If I try to shut it off keeping the power button pressed, nothing happens. The only thing that works is unplugging random stuff (sometimes unplugging 1 console works, other times I have to unplug all 4 devices). Every time this happens the problem is "real", meaning the 4 devices become unpowered, so it's not just an "alarm no working properly" problem. While I'm sleeping, of course, the power usage is what described on the list, 2 devices on standy, 1 off and 1 on. Today it happened again while I was playing with my Ps3. I unplugged it, problem went away. I plugged it again, and it kept working fine. I just can't figure out what's the problem. The only additional info I can provide is that this behaviour started after a big power outage last december 26 (a blackout that lasted almost all day) but the "surge protection" part of those UPS should be there for those problems, to leverage peaks when power goes away or gets restored. Another funny thing is, althought it might not be related, for a couple of days after that event the Wii was unable to power on, I thought its power transformer was broken, but then it suddenly started working again. I can be sure it's not the Wii overloading the UPS because the overload happens even if I leave the Wii unplugged. Any suggestion is really appreciated, and I can provide any additional info, if needed, that didn't come to mind right now. Thanks.

  Read the article

• Do RAID controllers commonly have SATA drive brand compatibility issues?

  - by Jeff Atwood

  We've struggled with the RAID controller in our database server, a Lenovo ThinkServer RD120. It is a rebranded Adaptec that Lenovo / IBM dubs the ServeRAID 8k. We have patched this ServeRAID 8k up to the very latest and greatest: RAID bios version RAID backplane bios version Windows Server 2008 driver This RAID controller has had multiple critical BIOS updates even in the short 4 month time we've owned it, and the change history is just.. well, scary. We've tried both write-back and write-through strategies on the logical RAID drives. We still get intermittent I/O errors under heavy disk activity. They are not common, but serious when they happen, as they cause SQL Server 2008 I/O timeouts and sometimes failure of SQL connection pools. We were at the end of our rope troubleshooting this problem. Short of hardcore stuff like replacing the entire server, or replacing the RAID hardware, we were getting desperate. When I first got the server, I had a problem where drive bay #6 wasn't recognized. Switching out hard drives to a different brand, strangely, fixed this -- and updating the RAID BIOS (for the first of many times) fixed it permanently, so I was able to use the original "incompatible" drive in bay 6. On a hunch, I began to assume that the Western Digital SATA hard drives I chose were somehow incompatible with the ServeRAID 8k controller. Buying 6 new hard drives was one of the cheaper options on the table, so I went for 6 Hitachi (aka IBM, aka Lenovo) hard drives under the theory that an IBM/Lenovo RAID controller is more likely to work with the drives it's typically sold with. Looks like that hunch paid off -- we've been through three of our heaviest load days (mon,tue,wed) without a single I/O error of any kind. Prior to this we regularly had at least one I/O "event" in this time frame. It sure looks like switching brands of hard drive has fixed our intermittent RAID I/O problems! While I understand that IBM/Lenovo probably tests their RAID controller exclusively with their own brand of hard drives, I'm disturbed that a RAID controller would have such subtle I/O problems with particular brands of hard drives. So my question is, is this sort of SATA drive incompatibility common with RAID controllers? Are there some brands of drives that work better than others, or are "validated" against particular RAID controller? I had sort of assumed that all commodity SATA hard drives were alike and would work reasonably well in any given RAID controller (of sufficient quality).

  Read the article

< Previous Page | 572 573 574 575 576 577 578 579 580 581 582 583  | Next Page >