Search Results

Search found 16587 results on 664 pages for 'virtual hardware'.

Page 576/664 | < Previous Page | 572 573 574 575 576 577 578 579 580 581 582 583  | Next Page >

  • why would resetting the Netgear N300 router fix my Win 7 laptop's slow wifi?

    - by rjnagle
    In the past day the wifi download speeds of my Win 7 HP 64 bit laptop have slowed considerably. I am trying to troubleshoot the problem and to figure out whether it's hardware related (i.e., is the Intel(R) Centrino(R) Wireless-N 2230 the problem?) or router related. I have a Netgear N300 router connected to my modem. I'm using Speedtest to measure my speed. First, during my problem state, my ipad can download and upload at normal speeds. It's only my Win 7 laptop which is having problems. Because my ipad downloads at normal speeds, that would tell me that the problem is specific to the laptop (either HW or SW). But when I restarted my Netgear router, the laptop wifi problems disappeared. That just doesn't make sense. If we know that one device can connect properly to the router, why would a laptop have problems? What are some possible reasons why this might happen? Also, during my problem state, I noticed that on my laptop upload speeds were faster than my download speeds. Anybody have a guess about what might cause upload speeds on one device to be faster than another? Is there any actions i could take (or options to enable) so this problem won't occur. (I initially thought my problem might be software related or memory related -- Norton AV or browser plugins. But even after I disabled everything and made sure memory footprint was minimal, the slowdown was still occurring -- and it solved itself altogether when the router was reset).

    Read the article

  • Latitude D600 USB port problem

    - by Moab
    Both USB ports stopped communicating on my D600, they have power, my optical mouse still lights up, no device works on the ports, everything is fine in Device manager in Dual boot XP and W7. Checked the bios, not much in there for USB. No usb device shows up when I use the F12 boot device menu either, so it must be some hardware issue. I have another hard drive with Ubuntu on it, popped it in and USB does not communicate with it either. Appears to have 5v but no communication, any Ideas besides another motherboard or USB card for the pcmcia slot (these don't work to well from my research)? I mostly use them for mass storage devices and pcmcia slots don't supply enough power for these devices. Thanks to all who answer with last ditch efforts. I hate to give up on it, its been good to me and still runs rather well for its vintage. EDIT: I did inspect the ports with a flashlight and did a partial disassembly of the laptop in an attempt to check the solder joints, but would require complete motherboard removal to see them, that is where I stopped. .

    Read the article

  • Ubuntu inside VirtualBox is slow

    - by Kapsh
    I am running an Ubuntu instance on VirtualBox inside XP. Here are the details: Host: Windows XP Pro Guest: Ubuntu 8.10 Total RAM: 3GB RAM For VM: 1GB Total Video Memory: 128MB Video Memory for VM: 40MB Hard Drive: 200GB Hard Drive for VM: 30GB Processor: 2.80GHz Core Duo The problem is that whenever I am inside the virtual machine, things seem so much slower in general. For example Firefox, Eclipse take longer to load, dragging windows show a lag etc. I have tried running Ubuntu before (not inside a VM) and it seemed fantastically fast. So I am disappointed to have to deal with this situation. But I need access to the XP partition without having to reboot and hence the attempt. I am surprised with the perceived slowness since the whole world seems to be doing virtualization and I cannot imagine everyone works on slow systems knowingly. My question is - is there something I should be doing to boost performance? Am I doing something wrong? This is my home machine and I am not sure if this is the right forum to ask. Thanks.

    Read the article

  • Obtaining clear cable signal with Hauppage 1191-950Q TV Tuner

    - by Kyle B.
    I bought a Hauppauge 1191 WinTV-HVR-950Q TV Tuner a while back, and I am attempting to use it to watch TV in Windows Media Center. I do not have cable TV, however I used to have Comcast. Through experimentation, I found that connecting my coax cable into my TV, I was able to view television (i.e. 2-1 = CBS, 5-1 = NBC, etc). This also works on a second TV I use in another room. When I connect the coax cable to my TV Tuner stick and scan TV channels in Windows Media Center, it only picks up 1 station (like 81 or something). My only conclusion on this is somehow the hardware in the television is decrypting a signal that the TV tuner stick is not able to. Is that possible? Should I try a different TV tuner? Any assistance would be appreciated. I also bought a Terk HD Indoor Antenna but my reception has been flakey, so I would rather go this route if possible.

    Read the article

  • USB Device Not Recognized (Mac)

    - by Nargis
    Fortunately, my Mac-pro also made one of my USB storage devices inoperable. My data loss in that USB device but such as another USB device and USB keyboard are unaffected. I have heard that my friend usually trigger this problem by having at least two devices plugged in - typically thumb drives/USB flash drives, and then once a second flash drive is plugged in that become unrecognized. I have only two USB ports and first I think port loose when I connect two USB devices. But later I found these hidden files (“.Spotlight-V100”, “.TemporaryItems”, “.Trashes”, and “._.Trashes”) are created by Mac OS. And before unrecognized that USB device I have deleted these files and my friend had also done the same action. Now I don’t want to test for next USB device to become unrecognized and I won’t deleted any hidden system file inside the flash drives. But I really want to know why these problems happened. Can I delete these hidden files when I only connect to virtual machine (Vista), because I used to delete all useless hidden files from USB flash drives? Any suggestions or thoughts to prevent this or alternative suggestions to fix the problem that take lossless would be much appreciated.

    Read the article

  • Why does my Windows 8 Pro Hyper-V guest have no internet?

    - by Perplexed
    Trying to get this working on my Windows 8 Pro machine. I created an External Switch Assigned the newly available adapter to a Guest machine with Win 2008 os. My host has internet connection. Host can ping Guest, Guest cannot ping Host. Guest has no internet connection. Pasting the IP of both host and guest. HOST ========================== Ethernet adapter vEthernet (EXTSW01): Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Hyper-V Virtual Ethernet Adapter #2 Physical Address. . . . . . . . . : 9C-B7-0F-0F-D7-D0 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::5434:a9fd:8611:d207%54(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.0.15(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : Saturday, September 8, 2012 12:34:44 PM Lease Expires . . . . . . . . . . : Saturday, September 15, 2012 12:34:44 PM Default Gateway . . . . . . . . . : 192.168.0.1 DHCP Server . . . . . . . . . . . : 192.168.0.1 DHCPv6 IAID . . . . . . . . . . . : 916240141 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-17-DC-C9-2C-9C-B7-0D-0D-D7-D0 DNS Servers . . . . . . . . . . . : 64.71.255.999 NetBIOS over Tcpip. . . . . . . . : Enabled GUEST ========================== Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft Virtual Machine Bus Network Adapter Physical Address. . . . . . . . . : 00-15-5D-3F-0F-00 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::953f:ec5c:5d84:1b50%11(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.0.20(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 0.0.0.0 DHCPv6 IAID . . . . . . . . . . . : 234886493 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-17-DD-2F-29-0F-15-5E-00-0F-00 DNS Servers . . . . . . . . . . . : ::1 127.0.0.1 NetBIOS over Tcpip. . . . . . . . : Enabled

    Read the article

  • What is the max connections via remote desktop for a small server?

    - by Jay Wen
    I have a small server running MS Server 2012. The CPU is a Xeon E3-1230 V2 @ 3.30GHz, 4 Cores, 8 Logical Processors, 8 GB RAM. Main HD is a Samsung 840, and the big storage is a 4 disk WD Black Raid 10 Array in a Synology NAS enclusure. My question is: given this hardware, approximately how many users can the system support via "Remote Desktop Connection"? Assume there are no licensing limits. These are not admin users. I know there is a two admin limit. This boils down to: What resources does one remote connection require? RAM? % of the CPU? Networking bandwidth? I guess the base case would be for a conection where the user is inactive or simply browsing cnn. Once you know this, you know how many you could fit on the machine before something is maxed-out. In reality, users would be mostly on Excel (multi-MB spreadsheets). I know the approx. resources currently required by each copy of Excel.

    Read the article

  • Setup shared internet connection on virtualbox with fixed IP

    - by Tom
    I am a web developer and until recently I have been using ubuntu as my OS. For many reasons, I have switched back to windows. I still want to keep my server on linux platform, so I setup my local server as a virtual machine. Everything works great, but i have a little struggle with the networking. Since I am working in different places and going around clients, I connect to all sorts of network with different settings. That means the possible IP range is very dynamic which causes issues when I work on my local server. At the moment I have a dynamic IP on my host and static IP on my guest. That way I can access the server from my host (by adding record to hosts file). I also have internet connection on the guest. But once i change networks, it does not work (assuming the network has different configuration). My question is, how to setup host-guest networking, so no matter what network I connect to, I can keep my static IP on guest, which is registered in hosts file on my host so I can access the webserver and also I will have internet connection on the guest? Hope it make sense. Thank you

    Read the article

  • proxy pass domain FROM default apache port 80 TO nginx on another port

    - by user10580
    Im still learning server things so hope the title is descriptive enough. Basically i have sub.domain.com that i want to run on nginx at port 8090. I want to leave apache alone and have it catch all default traffic at port 80. so i am trying something with a virtual name host to proxy pass to sub.domain.com:8090, nothing working yet and go no idea what the right syntax could be. any ideas? most of what i found was to pass TO apache FROM nginx, but i want to the do the opposite. LoadModule proxy_module modules/mod_proxy.so LoadModule proxy_http_module modules/mod_proxy_http.so <VirtualHost sub.domain.com:80> ProxyPreserveHost On ProxyRequests Off ServerName sub.domain.com DocumentRoot /home/app/public ServerAlias sub.domain.com proxyPass / http://appname:8090/ (also tried localhost and sub.domain.com) ProxyPassReverse / http://appname:8090/ </VirtualHost> when i do this i get [warn] module proxy_module is already loaded, skippin [warn] module proxy_http_module is already loaded, skipping [error] (EAI 2)Name or service not known: Could not resolve host name sub.domain.com -- ignoring! and yes, the app is working (i have it running on port 80 with another subdomain) and it works at sub.domain.com:8090

    Read the article

  • Any ideas why Ettercap filters aren't seeing packet data?

    - by Bryan
    I'm using an Ettercap filter to detect a query response coming back from a particular service on a remote machine. When I see a response from the service, I'm searching through the data in the packet to see if an offset is a specific value, and if so I'm changing the value at another offset. Trouble is, when I try this on a new virtual machine I built my Ettercap filter's no longer getting any data in the DATA.data variable available to it. if(ip.proto == TCP && tcp.src == 17867) { msg("Response seen!\n"); if(DATA.data + 2 == "\0x01") { msg("Flag detected!\n"); DATA.data + 5 = 0x09; } } The filter's getting applied to the traffic because "Response seen!" messages get printed out by Ettercap. However, "Flag detected!" messages do not. I think DATA.data is indeed empty because if I change my second "if" statement to check for DATA.data == "" then the "Flag detected!" message gets printed. Any ideas why this may be happening?! Also, if this is the wrong site to be asking questions like this, please let me know. I wasn't sure if it fit better here or somewhere like superuser or serverfault. By the way, this is a cross-post from StackOverflow... I should have posted on this forum instead I think. :)

    Read the article

  • Display errors using VMWare Player and Remote Desktop on Windows XP

    - by Tim
    I've come up against a weird display issue that I can't seem to find any "fix" for. When I first boot up my computer, everything behaves normally. If I start to use VMWare Player and/or Remote Desktop, my desktop starts having some odd video issues. The frames for some windows aren't drawn at all, if I move windows around rapidly, the area under where the window used to be isn't cleared (still shows artifacts of the content of the window), etc. In some cases, the minimize / restore / maximize buttons aren't drawn (but are click-able if you can guess where they are). I've tried the usual stuff - current drivers all around, using a single monitor, etc.. none of it seems to have any bearing. If I try to disable hardware acceleration, it tends to crash the computer. As I said earlier, it's running Windows XP, dual monitors, an NVidia en8400GS video card, asus p7p55d motherboard. Not sure what other pertinent details are needed. I would appreciate any help or suggestions!

    Read the article

  • Router intermittently failing

    - by nomen
    My old Asus router died a few weeks ago, so I thought I'd set up my Debian box to deal with routing my home network. I have a few complications, but I adapted my configuration from a previously working configuration, and I don't see why I am having intermittent problems. But I am having them! Every so often, my SSH connections to the router (and to the Xen virtual machines hosted by the router) just drop. I am unable to use the router's dns server. I can't ping the router. Etc. All of these things work most of the time, but break down intermittently, for a few minutes at a time. (I can provide more details, but I'm not sure what will be helpful) /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # Gigabit ethernet, internal network auto eth0 allow-hotplug eth0 iface eth0 inet manual # USB ethernet, internet auto eth1 allow-hotplug eth1 iface eth1 inet dhcp # Xen Bridge auto xlan0 iface xlan0 inet static bridge_ports eth0 address 10.47.94.1 netmask 255.255.255.0 As I understand it, this is sufficient to create the network interfaces, and even do some switching between Xen hosts and my eth0 interface. I installed and configured Shorewall to manage routing between the bridge and my internet-facing interface: /etc/shorewall/zones fw firewall net ipv4 lan ipv4 /etc/shorewall/interfaces net eth1 detect dhcp,tcpflags,nosmurfs,routefilter,logmartians lan xlan0 detect dhcp,tcpflags,nosmurfs,routefilter,logmartians,routeback,bridge /etc/shorewall/policy net all DROP info fw net ACCEPT info all all REJECT info /etc/shorewall/rules DNS(ACCEPT) fw net DNS(ACCEPT) lan fw Ping(ACCEPT) lan fw ... and so on, these all work, when the router is accepting traffic at all. /etc/shorewall/masq eth1 10.47.94.0/24 Also, the router is currently "working", and I checked on a problematic client: arp infrastructure infrastructure.mydomain (10.47.94.1) at 0:23:54:bb:7d:ce on en0 ifscope [ethernet] I tried it when the router was down, and I (eventually) got the same response. It took about 30 seconds to return, though.

    Read the article

  • Installed Windows 7 Ultimate on D Drive and previous Windows 7 Enterprise on C Drive has stopped starting up

    - by teenup
    Please please help! I have installed Windows 7 Ultimate on same hard drive on D Drive on my laptop and the previous Windows 7 Enterprise which was installed on C Drive is not booting up now. When I turn on my laptop, I see two Windows 7 on the screen, when I select newer one, it starts, but when I select older one which is Enterprise edition, system won't start and I get the DOS black screen with this error message: Windows Boot Manager Windows failed to start. A recent hardware or software change might be the cause. To fix the problem: Insert your Windows installation disc and restart your computer. Choose your language settings, and then click "Next." Click "repair your computer." Info: The boot selection failed because a required device is inaccessible. I notice that when I run the newer OS installed, the previous OS's drive (Which is D: now instead of C:) has become unusable and when I double click it, it asks me to format the drive. The data, that I had on my D Drive (Which is now C Drive for new OS), I had copied it to a network path and it is available. It was containing Windows 7 Users folder which I copied at that time when installing new windows. I have copied that Users folder again to the new OS's C Drive thinking it would run again, but of no use. Please please please...if someone can help...It is extremely required for me. Thanks a lot in advance.

    Read the article

  • Microsoft Deployment Toolkit 2012 Error

    - by Jacob Schaer
    I just started with MDT2012 recently in hopes of eventually getting away with using Ghost to deploy all of our department computers. When I test deploy in VirtualBox, it deploys the OS properly, but stops because of a network driver failure (it gets the "could not allocate resources" issue). On physical hardware (Latitude E6500, Optiplex 980, and an older Latitude) it gets through the multicast and stops immediately after with: "Setup was unable to create a new system partition or locate an existing system partition. See the Setup log files for more information" I've looked at the logs and never see anything really of note. Originally I was using DriverPacks from DriverPacks.net, but thinking it was a driver issue, I switched over to using Dell's cab driver packs. Still the same issue. I check and it did the HDD is all fine - it was properly partitioned, set to bootable, and was loaded with all the proper OS installer files. I'm using a flash drive to do the install - when I make changes to the deployment share I rebuild and copy the ISO to the drive, then use YUMI multiboot to start the ISO (probably irrelevant).

    Read the article

  • Limit access on Apache 2.4 to ldap group

    - by jakobbg
    I've upgraded from Ubuntu 12.04 LTS to 14.04 LTS, and suddenly, my Apache 2.4 (previous: Apache 2.2) now lets everybody in to my virtual host, which is unfortunate :-). What am I doing wrong? Anything with the Order/Allow lines? Any help is greatly appreciated! Here's my current config; <VirtualHost *:443> DavLockDB /etc/apache2/var/DavLock ServerAdmin [email protected] ServerName foo.mydomain.com DocumentRoot /srv/www/foo Include ssl-vhosts.conf <Directory /srv/www/foo> Order allow,deny Allow from all Dav On Options FollowSymLinks Indexes AllowOverride None AuthBasicProvider ldap AuthType Basic AuthName "Domain foo" AuthLDAPURL "ldap://localhost:389/dc=mydomain,dc=com?uid" NONE AuthLDAPBindDN "cn=searchUser, dc=mydomain, dc=com" AuthLDAPBindPassword "ThisIsThePwd" require ldap-group cn=users,dc=mydomain,dc=com <FilesMatch '^\.[Dd][Ss]_[Ss]'> Order allow,deny Deny from all </FilesMatch> <FilesMatch '\.[Dd][Bb]'> Order allow,deny Deny from all </FilesMatch> </Directory> ErrorLog /var/log/apache2/error-foo.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access-foo.log combined </VirtualHost>

    Read the article

  • PC in POST loop

    - by Antony Scott
    Hi, I have a custom built PC using a Gigabyte GA-EP35-DS3P motherboard with a Q6600 CPU. For the last 2 days it has got itself stuck into a POST loop. Saying that, I don't think it actually got in to the BIOS. It repeatedly lit up the LEDs and then not much more. Sometimes I could see the CPU fan twitch. Today I re-seated the DIMMs and it powered up straight away. Could this be a sign of an impending hardware failure? The PC is hooked up to a UPS, so I don't think it's a power spike or anything like that, as I have 2 other PCs on the same UPS and they're both fine. Yesterday, the first time this happened, I was getting a message which I think said "Scanning BIOS image on hard drive". I've been building and using PCs for well over 25 years and that's a new one on me! I don't think it's an over heating problem, as when the PC does finally boot up the CPU is running at 35-40C. Any help or suggestions would be greatly appreciated.

    Read the article

  • Matched or unmatched drives for RAID arrays?

    - by Will
    Looking around there is conflciting information on this, with some strongly suggesting one or the other. From my understanding the issue with matched drives is that the wear on both drives is more or less the same, so the potential for the second drive failing with or very soon after the first is pretty high. People also claim matched drives give substianatally higher performance however assuming the unmatched drives are more or less the same (eg 2, 1 TB STATA II 7200rpm drives with 32MB cache), would the minor differences between say a Seagate and a Western Digital one (say one has a 128MB/s read rate, and the other a 150MB/s read rate, as well as I guess various other minor differences) actually cause any notable performance loss, ie potentialy worse than two matched 128MB/s drives, or does RAID not really care and give you essentially an optimal solution (eg upto 278MB/s total read speed for RAID 0 and 1) and similar for other RAID with more "unmatched" drives (5 and 1+0 come to mind as possibilities)? Also I couldnt find much info on how this is different on different RAID setups, eg RAID 0 or RAID 1, software or hardware RAID, etc. I'm assuming such things have an effect, and thats it's not all the same for RAID in general?

    Read the article

  • Dual hard drive Windows 7 system, modified the registry to get programs to install on second drive, now IE doesn't work

    - by paul
    I have a dual hard drive Windows 7 system, Windows is installed on an SSD (C:) and I modified the registry to try to force programs to install on second HDD drive (another letter). The registry edits are pretty simple, just a few keys in HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion to change the drive letter. For the most part the system is very fast and works great, but IE doesn't work anymore. With IE10, it opens for a flash with a white window then closes. I tried installed IE11 which opens a white window for a few seconds, doesn't respond, then crashes. I've tried all the solutions I could find. This includes resetting the IE settings, "uninstalling" and re-installing IE, which is just turning it on and off in "Turn Windows Features on or off", copying the Program Files\Internet Explorer files onto both/either drives, changing the registry keys back to use C:, lots of rebooting, and safe mode. Nothing has worked. I don't see errors in the event viewer, but I might not know what to look for. Any ideas on how to get IE running? I don't need IE for daily browsing, I just need it for cross-browser testing on sites I build and on the rare occasion a page only works in IE. I don't really want to use a virtual machine, but would be ok with something standalone like tredosoft's, but I'm not aware of something like that for current versions of IE.

    Read the article

  • Apache2 doesn't serve PHP-scripts correctly [closed]

    - by cmbrnt
    I've run into a problem with my Apache 2.2.16 configuration, running on Debian Squeeze. The problem is that it stopped serving PHP5-scripts completely. When I try to access the sites with Google Chrome, it instead downloads a file called "download", which contains the contents of the script. This is of course not a good thing. It does serve common html-files perfectly... I've been at this for quite a while now, and after all the googling and troubleshooting, I thought it would be a good time to ask you guys. Here's what I've got: The php5 and libapache2-mod-php5 packages are installed /etc/apache2/mods-available contains both php5.load and php5.conf, and these are symlinked from the mods-enabled directory The /etc/php5/ directory is left untouched since the installation. Here's the contents of /etc/apache2/mods-available/php.load: LoadModule php5_module /usr/lib/apache2/modules/libphp5.so And /etc/apache2/mods-available/php.conf: <IfModule mod_php5.c> <FilesMatch "\.ph(p3?|tml)$"> SetHandler application/x-httpd-php </FilesMatch> <FilesMatch "\.phps$"> SetHandler application/x-httpd-php-source </FilesMatch> <IfModule mod_userdir.c> <Directory /home/*/public_html> php_admin_value engine Off </Directory> </IfModule> </IfModule> What am I missing? This is a server with modified virtual hosts and the like, so I might have changed some settings which causes this problem, but simply purging and reinstalling is not an option so far, since the configuration is quite extensive. Any help would be great. Thanks.

    Read the article

  • How to set up Windows 7 Professional as a NAS

    - by Enyalius
    I searched and didn't find any answers, so please forgive me if this is a repeat. Anyway, I have an older computer that I'm using as an HTPC, and I was hoping that I could use it as a NAS/multimedia server, as well. My primary uses would include accessing content on my PS3 (same LAN), accessing content from other computers on my home network and (if I can) accessing content from my Android phone over the internet. I have used SubSonic to stream music to my Android phone and other computers before, but I would really like to find a way to do this natively if possible. I know that I can buy external hard disk cases that can plug in the USB port of my router, that I can get a Drobo or other network storage solution, but I would really just rather not spend the money (especially considering that I already have a computer that I should be able to use). Hardware involved: Apple AirPort Extreme base station router (most recent revision) Home Theater Personal Computer: Core 2 Duo @ 2.4GHz, 8GB DDR2 RAM, ~3.5TB hard drive space Sony Playstaiton 3 Thin 120GB HTC Thunderbolt (I have 4G coverage) rooted and running Android 2.2.1 Various Apple laptops Various Windows 7 desktops/laptops Thanks in advance! Note- I have looked at open source NAS software but I would like to preserve the Windows Media Center functionality in Windows 7, so other NAS software is not an option for me currently. .

    Read the article

  • Pull network or power? (for contianing a rooted server)

    - by Aleksandr Levchuk
    When a server gets rooted (e.g. a situation like this), one of the first things that you may decide to do is containment. Some security specialists advise not to enter remediation immediately and to keep the server online until forensics are completed. Those advises are usually for APT. It's different if you have occasional Script kiddie breaches. However, you may decide to remediate (fix things) early and one of the steps in remediation is containment of the server. Quoting from Robert Moir's Answer - "disconnect the victim from its muggers". A server can be contained by pulling the network cable or the power cable. Which method is better? Taking into consideration the need for: Protecting victims from further damage Executing successful forensics (Possibly) Protecting valuable data on the server Edit: 5 assumptions Assuming: You detected early: 24 hours. You want to recover early: 3 days of 1 systems admin on the job (forensics and recovery). The server is not a Virtual Machine or a Container able to take a snapshot capturing the contents of the servers memory. You decide not to attempt prosecuting. You suspect that the attacker may be using some form of software (possibly sophisticated) and this software is still running on the server.

    Read the article

  • Onboard Ethernet suddenly stopped working to router

    - by AfterschoolHobbist
    Hey guys, yesterday I have a sudden problem of my Ethernet connection to my router. My computer is a Pendium 4 with Window XP SP3 running on it and it was working fine earlier in the day, but yesterday night was the start of the problem. My computer is unable to ping to the router and to any other website and unable to get internet connection. As beside it was connected to a hub, I directly connected it to the router directly and the same problem occurred, being unable to ping to the router (and connecting to it) and still no internet access. My directly connected to the modem and the problem still persisted. For each connection, I connected it to my computer and my laptop and my laptop was able to connect, while my desktop computer was unable. I wondered if it was a OS issue and ran a live Ubuntu CD to see if Ubuntu was able to connect to the internet, but the issue persisted and I was unable to get internet access. I then set my router's lease time to 1 hour and waited. After 1 hour, the lease for my computer was removed and I hoped this worked, but it didn't work, but something strange is acting up. My desktop computer is still unable to ping to the router or connect to the internet, but for some reason, my router and desktop computer is still able to contact each other by providing a lease of an local ip address. The router record of a lease to my desktop computer, and when I do ipconfig, my desktop also recognize that it has been provided a local ip address. I have concluded that this is a hardware issue and the only solution to fix this is to by a network card adapter, but I am wondering if anyone has any solutions that could explain why this happen, why my mac address is 01-23-45-67-89-ab, and is there any way to fix it without buying a new network card? Thanks in advance.

    Read the article

  • Apache forwarding to tomcat shows a blank page

    - by MNS
    I have an application running on tomcat at http ://www.example.com:9090/mycontext. The host name in server.xml points to www .example.com. I do not have localhost anymore. I am using apache to forward requests to tomcat using mod_proxy. Things work fine as long as the ProxyPath is /mycontext. The server name setup in virtual host is www .abc.com and http ://www.abc.com/mycontext works fine. However I would like to ignore the context path and simply use http://www.abc.com/ to forward requests to http://www.example.com:9090/mycontext. When I do this, apache shows me a blank page. What am I missing here? I have not changed anything in server.xml except the default host to www .example.com. <VirtualHost *:80> ServerName www.abc.com ProxyRequests Off ProxyPreserveHost On <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPass / http://www.example.com:9090/mycontext ProxyPassReverse / http://www.example.com:9090/mycontext </VirtualHost> Thanks

    Read the article

  • How can I make my Super keys (Windows Key) behave more like Ctrl/Alt/Shift in Linux

    - by deltaray
    After using the Ctrl + "arrow keys" for 13 years to switch virtual desktops in X windows, I've been convinced recently to change to using the Super keys instead (the windows key and the context menu key, which I've remapped). This all works fine for the most part. However, something is still picking up the key events that these keys are sending as if they are a normal alphanumeric like key. For example, I first noticed this in Google Docs spreadsheet that if I press the windows key alone over top of a cell, that it starts editing that cell. It doesn't insert anything, it just sends a key event that Firefox sees and starts editing the cell. This caused problems on a collaborative document I was working on as the way Google docs works, it led to me accidentally erasing the data in a few fields before I realised what was going on. I like using the super keys, but I want them to behave more like a Ctrl or Alt key does in that its a modifier key and doesn't send anything until a second key is pressed. My setup is the following: Ubuntu 10.10 XFCE 4 Microsoft Natural Ergo 4000 keyboard (with the logo scratched out) The following is my .Xmodmap file: remove Lock = Caps_Lock keycode 66 = Escape ! The below maps my other windows context menu key. keycode 135 = Super_R Edit: As requested, here is the relevant output from xev for a keypress and keyrelease of my Super_L (left windows key) KeyPress event, serial 34, synthetic NO, window 0x8200001, root 0x15d, subw 0x0, time 2428849342, (177,174), root:(182,228), state 0x10, keycode 133 (keysym 0xffeb, Super_L), same_screen YES, XLookupString gives 0 bytes: XmbLookupString gives 0 bytes: XFilterEvent returns: False KeyRelease event, serial 34, synthetic NO, window 0x8200001, root 0x15d, subw 0x0, time 2428849430, (177,174), root:(182,228), state 0x50, keycode 133 (keysym 0xffeb, Super_L), same_screen YES, XLookupString gives 0 bytes: XFilterEvent returns: False

    Read the article

  • What sound cards are there besides Creative's that offer benefits for gaming?

    - by Vilx-
    Many years (6? 7?) ago I bought an Audigy sound card to replace the onboard sound and was astonished at the improvement in games. It was a completely different sound, the whole experience became way more immersive. As the time has passed however the card has become old. The support for the latest Windows versions is declining and newer technologies have definitely been developed. So I was starting to wonder - what newer hardware exists? Sure, there is the Sound Blaster X-Fi, but that's quite expensive and I'm not entirely thrilled by past policies of Creative either (like the whole affair with Daniel_K). But are there any alternatives? EAX is a patent by Creative, so it's doubtful that any other manufacturer has implemented it. And I haven't heard of any competing standards either. To clarify, what I would like is something like a "sound accelerator". A sound card that would offload sound processing from my CPU while at the same time giving astounding effects that would be impractical to do on CPU in the first place. I'm not interested in absurd sampling rates (for the most time I can't tell MP3 and a CD apart) or uncountable channels (I'm using stereo headphones). But I am interested in special effects in games. Are there any alternatives or is Creative a monopoly in this market?

    Read the article

< Previous Page | 572 573 574 575 576 577 578 579 580 581 582 583  | Next Page >