Search Results

Search found 19969 results on 799 pages for 'nate bit'.

Page 578/799 | < Previous Page | 574 575 576 577 578 579 580 581 582 583 584 585  | Next Page >

• Apache /server-status/ gives a 404 not found

  - by kapshure

  I am trying to solve a problem where Apache stats aren't displaying correctly in Munin. I've ran through quite a bit of checks and tests regarding Munin setup, but I think my issue is related to Apache, but my skill set there is lacking. first, system info: monitored server CentOS 5.3 kernel 2.6.18-128.1.1.el5 Apache/2.2.3 "server-status" directive in httpd.conf (i've cross-compared this with another system that i did a successful parallel install of Munin on, correctly showing Apache stats, and the directive below is the same for both) ExtendedStatus On <Location /server-status> SetHandler server-status Order deny,allow Deny from all Allow from 127.0.0.1 </Location> ran lynx http://localhost/server-status got HTTP/1.1 404 taking a look at Apache access_log: 127.0.0.1 - - [13/Oct/2010:07:00:47 -0700] "GET /server-status HTTP/1.0" 404 11237 "-" "Lynx/2.8.5rel.1 libwww-FM/2.14 SSL-MM/1.4.1 OpenSSL/0.9.8e-fips-rhel5" mod_status is also loaded: % grep "mod_status" /etc/httpd/conf/httpd.conf LoadModule status_module modules/mod_status.so iptables is turned off also i did notice that the ownership status on httpd.conf on this system is root.root.. whereas the system that is displaying correctly is apache.www -- not certain that this matters?? its got to be permission issue, but i'm not certain where the permissions are messed up. any thoughts on why the test of server-status is giving me a 404?

  Read the article

• Building a Media Center PC with Comcast Cable...?

  - by Rob

  Alright - so this might be a stupid question but I've never been all that much into TV. I currently have Comcast cable. I've just got the 'basic' 2-60 package or whatever; I've just always plugged the cable into the back of my TV. I've never had a cable box. Recently, Comcast has been pulling channels off of my line-up. Most recently, the stole the TV Guide channel from me. I'm told this is part of a push to get customers to switch to their digital line-up. But, I'm also told it requires some sort of digital receiver for each TV you've got. I don't want to buy a bunch of these digital receivers and I don't want to pay the monthly rental fee...but I have heard of how awesome media center PCs are and some really cool things they can do. And, I've got loads of PC parts sitting around. So, can someone guide me through this a bit? Are there computer video cards or TV tuners that are going to work with Comcast's digital cable? What kind of price range are we looking at?

  Read the article

• /usr/bin/python (Python 2.4) was deleted on CentOS 5. I compiled from source but yum is still broken. How can I get everything back to the way it was?

  - by Maxwell

  I saw a lot of other questions like this but none of them answered the exact part I am having trouble with (actually installing the Python RPM). Someone on my system deleted /usr/bin/python and /usr/bin/python2.4 on my 64 bit CentOS 5.8 installation. I recompiled Python 2.4 from source, but now whenever I try to yum install anything I get the following error: [root@cerulean-OW1 ~]# yum install httpd There was a problem importing one of the Python modules required to run yum. The error leading to this problem was: No module named yum Please install a package which provides this module, or verify that the module is installed correctly. It's possible that the above module doesn't match the current version of Python, which is: 2.4 (#1, Dec 16 2012, 09:16:56) [GCC 4.1.2 20080704 (Red Hat 4.1.2-52)] If you cannot solve this problem yourself, please go to the yum faq at: http://wiki.linux.duke.edu/YumFaq I checked http://wiki.linux.duke.edu/YumFaq and it said the following: If you are getting a message that yum itself is the missing module then you probably installed it incorreclty (or installed the source rpm using make/make install). If possible, find a prebuilt rpm that will work for your system like one from Fedora or CentOS. Or, you can download the srpm and do a rpmbuild --rebuild yum*.src.rpm I tried going to http://rpm.pbone.net/index.php3/stat/4/idpl/17838875/dir/centos_5/com/python-2.4.3-46.el5.x86_64.rpm.html to install Python, which resulted in the following error: [root@cerulean-OW1 ~]# rpm -Uvh python-2.4.3-46.el5.x86_64.rpm error: Failed dependencies: python-libs-x86_64 = 2.4.3-46.el5 is needed by python-2.4.3-46.el5.x86_64 So I tried installing python-libs-x86_64, which resulted in the following: [root@cerulean-OW1 ~]# rpm -Uvh python-libs-2.4.3-46.el5_8.2.x86_64.rpm warning: python-libs-2.4.3-46.el5_8.2.x86_64.rpm: Header V3 DSA signature: NOKEY, key ID 192a7d7d Preparing... ########################################### [100%] package python-libs-2.4.3-46.el5_8.2.x86_64 is already installed file /usr/lib64/libpython2.4.so.1.0 from install of python-libs-2.4.3-46.el5_8.2.x86_64 conflicts with file from package python-libs-2.4.3-46.el5_8.2.x86_64

  Read the article

• Exchange 2010: Find Move Request Log after move request completes

  - by gravyface

  EDIT: significantly changed my question here to streamline it a bit. I've gone ahead and used 100 as my corrupted item count and ran it from the Exchange Shell. So the trail of tears continues with my SBS 2003 to 2011 migration: all the mailboxes have moved mailbox store from OLDSERVER to NEWSERVER, with the Local Move Requests completing successfully, except for one. What I'd like to do now is review the previous move request log files: when they were in progress, I could right-click Properties Log View Log File, but now that they're completed, that's not available. Nor can I use: Get-MoveRequestStatistics <user> -includereport | fl MoveReport ...as the move request has now completed and it errors out with "couldn't find a move request that corresponds...". Basically what I'd like to do is present the list of baditems to the user so that they're aware of what items didn't come across and if anything important was lost, be able to check their current OST, an archive.pst, etc. to recover it if possible. If this all needs to be wrapped up in a batch Exchange power shell command to pipe the output to log files on disk somewhere, I'm all ears, and would appreciate it for the next migration we do.

  Read the article

• How do I run a stable Windows XP kvm guest on Ubuntu 10.04?

  - by Jean-Paul Calderone

  I have three Windows XP guests running on a recently upgraded 64-bit Ubuntu 10.04 system. Occasionally (on the order of once every few days), one of the guests will become non-responsive and the kvm process on the host which is running that guest will start consuming 100% CPU. It will continue to do so until it is killed. When restarted, it will be fine for a while, and then the issue repeats. The kvm command line used to run all three guests is this: /usr/bin/kvm -S -M pc-0.12 -enable-kvm -m 1024 -smp 1 -name bigdog21vmxp1 \ -uuid ea47ff84-125b-16f7-9a4d-a6d0d8bab46a \ -chardev socket,id=monitor,path=/var/lib/libvirt/qemu/bigdog21vmxp1.monitor,server,nowait \ -monitor chardev:monitor \ -localtime \ -boot c \ -drive file=/var/lib/libvirt/images/windowsxp-1.qcow2,if=ide,index=0,boot=on,format=qcow2 \ -net nic,macaddr=54:52:00:02:06:0e,vlan=0,name=nic.0 \ -net tap,fd=58,vlan=0,name=tap.0 \ -chardev pty,id=serial0 \ -serial chardev:serial0 \ -parallel none \ -usb \ -usbdevice tablet \ -vnc 127.0.0.1:1 \ -k en-us \ -vga cirrus \ -soundhw es1370 Why do the systems misbehave this way sometimes? And what configuration can I change in order to fix it? Or, if the problem is due to a bug in kvm, what is the process for isolating a kvm failure so that the developers have a chance of fixing it?

  Read the article

• SATA HDD stuttering on reads (LED on)

  - by jdehaan

  I hope I can get some new ideas to solve the issue. What I have: AMD Phenom II X4 905e Box, Sockel AM3 Gigabyte GA-MA790XTA-UD4, AMD 790X, AM3 ATX WD Caviar GreenPower 1,5TB SATA II 4GB Kit OCZ DDR3 PC3-10666 Platinum Low-Voltage CL7 HIS HD 4670 iSilence4 DDR3 1024MB Native HDMI Dual-DVI, PCI-Express Behavior: Everything works normally excepting the HDD accesses. The drive seems to get stuck in reading data (LED drive by Mainboard is on for a while) then recovers and goes on. There is a delay of more than 30s sometimes. Often it is a matter of 5-10s. This does not seem related to the workload of the disk. What I tried so far: Use different SATA port: I switched from the SATA3 to SATA2 then the SATA driven by the CPU, no difference. Turned AHCI off, drove the SATA in IDE mode, same behavior, now I felt like the HDD has problems Deactivated energy saving settings (BeQuiet, ...), disabled 3 CPUs (msconfig) supposing some race condition or trouble with changing freqs, same trouble With Windows7 Professional 64Bit, I installed the hotfix http://support.microsoft.com/?scid=kb%3Ben-us%3B976418&x=8&y=9 with no success. The problem description matches what I experienced, so I felt lucky but was quite in a sad mood after being deceived. Burned the DLG 5.04f DataLifeGuard CD from WD to check the drive. All tests passed, to my surprise! Installed an Ubuntu on the same drive i386 flavour. Drive still in IDE mode, exactly the same behavior. So the OS does not matter. What I did not try yet: http://www.gigabyte.eu/Support/Motherboard/BIOS_Model.aspx?ProductID=3263 I have a F2 BIOS and there is a F3a Beta, did someone have similar issues that were solved by this update? It is a beta so I fear upgrading a bit and I could find no release notes at all on the net, not really serious work maybe they had issues translating from Chinese??? Using another HDD drive Does someone have other hints or a similar issue? Maybe it is neither the HDD nor the Mainboard/BIOS?

  Read the article

• Any way to move Office Starter To-Go to a non-flash drive?

  - by Scott Bussinger

  Microsoft's Office Starter edition has an interesting option to create a portable version on a USB flash drive using the "Microsoft Office Starter To-Go Device Manager". This creates a portable version of the Word and Excel starter editions (limited versions of the normal applications that include ads). This would be great for use in Virtual Machines since it requires no registration and has a perpetual license. But I want to copy the files off of the flash drive and just store them in the VHD. The problem is that it appears when you try to run the office.exe executable from anywhere but the USB drive you get the error "Microsoft Office Starter To-Go cannot be launched because it is installed on an unsupported device." Any ideas what it is objecting to and is there a legal workaround for this? A limited but legal and portable version of Word and Excel is a great idea. But tying it specifically to a USB flash drive seems a bit odd. They don't seem to care how many of those flash drives you create so it's not clear what the restrictions are about.

  Read the article

• Trouble installing SSL Certificate on Apache

  - by jahufar

  We have a dedicated server with GoDaddy running Plesk that requires SSL. I've generated the certificate files and I created a vhost_ssl.conf (since I can't edit the default plesk apache configuration http.include, vhost_ssl.conf gets Included to httpd.include) that tells apache where to find the certificate files: SSLCertificateFile /usr/local/psa/var/certificates/domain.com.crt SSLCertificateKeyFile /usr/local/psa/var/certificates/domain.com.key SSLCertificateChainFile /usr/local/psa/var/certificates/sub.class1.server.ca.pem When I stop/start apache, it refuses to start up. The error_log does not have anything on it either (which is strange). Then I opened up httpd.include and found this bit: <VirtualHost 208.xxx.xxx.xxx:443> ServerName domain.com:443 ServerAlias www.domain.com UseCanonicalName Off SSLEngine on SSLVerifyClient none SSLCertificateFile /usr/local/psa/var/certificates/certagC9054 Include /var/www/vhosts/domain.com/conf/vhost_ssl.conf Then I commented out SSLCertificateFile /usr/local/psa/var/certificates/certagC9054 (which is plesk's SSL certificate) and restarted apache and it worked perfectly fine. It seems that Apache does not like multiple SSLCertificateFile within the same VirtualHost directive? As anyone who worked with plesk knows, I can't just remove SSLCertificateFile directive in httpd.include as plesk will overwrite my changes when someone uses it - which is why it's in vhost_ssl.conf. So I'm stuck and this is beyond my meager admin skills. Would appreciate someone who knows what (s)he's doing to tell me whats going on. Thanks in advance.

  Read the article

• Page pool memory

  - by legiwei

  I'm currently using Windows XP SP3 32 bit, using C2D E6320 with 2GB RAM. When I am playing Starcraft 2, I encounter an error where it says my system is running low on page pool memory. Starcraft graphic settings suggested a high settings for me. I do not think it has to do with my GC but with my RAM. I then made a search to try to rectify the problem. Apparently, it's something to do with my virtual memory. I then proceed to try to the suggested solution which is to temper the registry and limit the page pool memory to 384MB. However, having done so, I still could not achieved it. I've seen screenshot settings of windows XP with 2GB having 384MB of page pool memory. My default settings puts it at 195MB whereas when I try to increase the pool limit, it can only go to a max of 229MB. I tried increasing my RAM capacity to 3GB but the pool limit still remains. I like to know how to increase my page pool memory. I've tried searching for solution but to no avail other than the one that I've mentioned above (which didn't solve my problem completely).

  Read the article

• Need to Remove Exchange 2003 Server That Crashed During Transition to 2010

  - by ThaKidd

  As the title stated, we were running an Exchange 2003 server that we knew was going down soon so we purchased a second server and installed Exchange 2010 into the AD. We managed to move all of the mailboxes off of 2003 and also managed to get the Offline Address Book setup on 2010. At this point the 2003 server bit the dust and will no longer boot. Therefore we were unable to properly uninstall Exchange and remove the last 2003 server so it still exists in AD. As far as the clients are concerned, everything is working properly. However, when I run the Microsoft Exchange Profile Analyzer, I still see the old server and its Administrative Group. I am going to guess that since the old server is showing up in AD, I will not be able to raise Exchange or AD functionality (as the 2003 server was also the only AD DC) levels. I have forced the 2003 DC out of AD so that is no longer an issue. Old Setup: Windows 2003 Server Enterprise & Exchange 2003 Standard New Setup: Windows 2010 Server Enterprise & Exchange 2010 Standard Two Questions: How do you go about manually forcing the 2003 server and its administrative group out of AD? When that is finished, where do you raise the Exchange mode (can't find this for the life of me)?

  Read the article

• Route traffic from one VPN to a second VPN

  - by Dominic

  I have set up an OpenVPN server on my windows 7 64-bit PC. I also have a subscription to a VPN service. My aim is to be able to connect my android phone to the VPN server on my PC, and then route all traffic through the VPN service. I have a NetGear WPN824 router. I can get it working if I my phone is on my local network. Then I can connect my phone to the VPN server using the local IP address of my PC. In Network Connection in the control panel, I share the connection used by the VPN service with the connection used by the VPN server. Then when I browse the internet on my phone, all traffic goes through the VPN service. Very nice. But if my phone is outside my local network, so I have to connect my phone to the local VPN using my PC's external IP address, then this method doesn't work. If I connect my PC to the VPN service and then try to connect my phone to my own VPN, it just doesn't connect (the initial TLS handshake times out). If I connect my phone to the local VPN first, then this connection is lost as soon as I connect my PC to the VPN service. Does anybody know how I can get this working? Many thanks Dominic

  Read the article

• Port Forwarding(?) TD-W8961nd

  - by rich

  I have a bit of a weird internet setup. I am connected via a decent WiFi connection (from work) which I pick up using a Buffalo Airstation Wireless-G box. This simply picks up the signal and gives me 4 ethernet ports to connect to. That's all fine and works as it should. I also have a TP LINK TD-W8961nd router which used to be connected to the Airstation via an ethernet cable so I could essentially have WiFi access in my house. To cut a long story short I can't remember how the hell I got it to work and I can't find the notes I scribbled down on how to do it. I'm pretty sure I need to tell the router what ip to pick up the internet connection from and have the local wifi as a seperate network. How the hell I do that I have no idea right now. Can anyone give me some advice on this? If you need more information ask and I will be able to do so. Cheers in advance. edit I'm in work at the moment so I can't give 100% details but I will be able to later on.

  Read the article

• Slow File Copy observed copying 40GB files across network to iSCSI device

  - by Rick

  Here's a curious ones for the gurus: Setup: Source Machine: Windows Server 2003 R2 machine with local hard drive. VHD file of 40GB. 1 x 1Gbps network card, Cat6 cable, switch. Target Machine: Windows Server 2008 R2 machine with iSCSI connection to iSCSI target on separate machine (1TB, RAID5). 1 x 1Gbps network card, Cat6 cable, connected to same switch as for Source Machine. Second 1Gbps network card, Cat6 cable, connected via isolated switch to the iSCSI target. Switches are Netgear JGS524 model (web managed). If I copy from the Win2003R2 machine to Win2008R2 machine local drive I get 40GB in 45 minutes, 36 seconds. If I copy from the Win2008R2 machine to the iSCSI target (local drive to iSCSI target) I get 40GB in 37 minutes 56 seconds. If I copy from the Win2003R2 machine to the iSCSI target via the Win2008R2 machine I get 40GB in 3 hours, 50 minutes, 24 seconds. All copies were done via the following command issued on the Win2008R2 box: XCOPY <source> <target> /J XCOPY /J - Copies using unbuffered I/O. Recommended for very large files. So, what's the bit I'm missing here? Why does a back-to-back copy take in total 1 hour, 23 minutes, 32 seconds when a "straight through" copy take almost 3 times as long? Switches show no errors, network hovers around the 3% utilisation mark for the duration of the copy (whereas the "back-to-back" copies are around the 25% utilisation mark). What have I missed?

  Read the article

• NFS high CPU usage

  - by user269836

  Hello, I have a very strange issue. I have next server: Intel(R) Xeon(TM) MP CPU 3.16GHz cat /proc/cpuinfo | grep proce | wc -l 8 free -m total used free shared buffers cached Mem: 28203 27606 596 0 10789 9714 -/+ buffers/cache: 7103 21100 Swap: 24695 0 24695 RAID card *-storage description: RAID bus controller product: MegaRAID vendor: LSI Logic / Symbios Logic physical id: 7 bus info: pci@0000:13:07.0 logical name: scsi2 version: 01 width: 32 bits clock: 66MHz capabilities: storage pm bus_master cap_list rom configuration: driver=megaraid latency=32 resources: irq:134 memory:d8ff0000-d8ffffff(prefetchable) memory:df600000-df60ffff(prefetchable) HDD: 10x148Gb SCSI U320 15k - RAID5 /dev/sdb1 807G 674G 93G 88% /storage /dev/sdb1 /storage ext4 defaults,usrjquota=aquota.user,grpjquota=aquota.group,jqfmt=vfsv0,noatime,nodiratime,noacl,errors=remount-ro 0 1 network cards ethtool -i eth0 driver: tg3 version: 3.116 firmware-version: 5704-v3.36, ASFIPMIc v2.36 bus-info: 0000:10:02.0 ethtool -i eth1 driver: tg3 version: 3.116 firmware-version: 5704-v3.36, ASFIPMIc v2.36 bus-info: 0000:10:02.0 ifconfig bond0 Link encap:Ethernet HWaddr 00:0f:1f:ff:d6:4d inet addr:192.168.15.71 Bcast:192.168.15.255 Mask:255.255.255.0 inet6 addr: fe80::20f:1fff:feff:d64d/64 Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:1062818202 errors:0 dropped:3918 overruns:0 frame:0 TX packets:1041317321 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:10000 RX bytes:258867684559 (241.0 GiB) TX bytes:396569192650 (369.3 GiB) this server running only nfs-kernel-server uname -a Linux nas2-backup 2.6.32-5-amd64 #1 SMP Sun Sep 23 10:07:46 UTC 2012 x86_64 GNU/Linux Debian 6. What do I have, once per day or two, LA goes up, it can be reached around LA: 40 but if I do: nfs-kernel-server restart. Every thing is OK. But on the next day or a little bit later, LA goes up again. Servers are connected to d-link dgs 1016d with 24 GBits ports. I have tried everything to find out what the problem is. Why it's happening, but still I can not resolve this issue. Any ideas on what is happening here?

  Read the article

• Use Mac OS X Server As Development Environment

  - by macinjosh

  I've installed Mac OS X Server 10.6.3 on my laptop to use as my normal OS. I do a lot of web development and thought it would be handy to run OS X Server so I could more easily manage my local development environment (Apache Virtual Hosts, Hostnames for each local site, etc). I'm really enjoying the new setup except for one problem. DNS. My ideal situation would be to add a site (some-site.local) in the Web Service and then go to the DNS Service and add a primary record for the new site. I actually got this working at one point but after a reboot it stopped working! The records look the same as they did before the reboot but the site doesn't come up in Safari. Here is a list of my needs: Need to be able to add new domains at a whim Domains always map to a site on the same box's Web Service Local & External IPs often change It would nice if it worked on any network (i.e. WiFi at the airport or coffee shop) Sites only need to be accessible locally Configuration should stay put even after rebooting I've done some googling and used this as a bit of guide. In the past I've used MAMP and then just a local Apache/PHP/MySQL install with a manually managed hosts file. I'd rather not go back.

  Read the article

• Windows XP laptop doesn't appear in WSUS All computers list

  - by George

  I have this one laptop that doesn't appear in WSUS all computers list. We have about 23-25 PCs/laptops/servers in the network, all, but one are listed in WSUS. This is what I have done so far: 1) Changing Updates on local PC: Go to your Windows XP client and start a new Microsoft Management Console (MMC). At Start, Run, type MMC. Use Ctrl+M to add a new snap-in. Click Add, and then add the Group Policy Object Editor for the Local Computer. Click Close, and then click OK. Expand the Local Computer Policy. Under Computer Configuration, go to Administrative Templates, Windows Components, Windows Update. In the right-hand pane, double-click Specify intranet Microsoft update service location. Configure the settings to reflect my WSUS server. Click OK and then close the MMC without saving it. executed wuauclt.exe /detectnow 2) Edited registry key to be pushed to the PCs using GPO [HKEY_LOCAL_MACHINE\SOFTWARE\Policies\Microsoft\Windows\WindowsUpdate] "WUServer"=http://wsusserver "TargetGroupEnabled"=dword:00000001 "TargetGroup"="WINXP" "WUStatusServer"=http://wsuswerver 3) executed wuauclt /resetauthorization /detectnow 4)Synchronised and refreshed the group I am running out of ideas here. The client is running Windows XP pro, WSUS version is 3.0 and is running on Windows 2008 R2 64-bit. Please, help! Thanks! EDIT 13.IX.2012 @ 15.40 I should have also mentioned that we do have a Windows Update GPO for workstations group and that laptop is a part of that group.

  Read the article

• Getting Windows (VMware) to load from OSX's localhost without an Internet Connection

  - by Jonah Goldstein

  I'm using MAMP to host my local sites, and VirtualHostX so that I can access sites during local development via a convenient URL like mysite.dev I'm also running Windows XP via VirtualBox, and it would be great to be able to load up any of my local sites within windows while offline as currently often working without access, on the move, unfortunately. I know that I can append my IP and a nice domain name to the host file in C:/WINDOWS/system32/drivers/etc ... and i can find my IP simply through terminal with "ifconfig" while I'm online. The problem is that when I'm not online, there's no IP. Even if there is an IP (when i have a connection), I still have grab it and update the windows hosts' file all the time, since I'm developing from a laptop and have a new IP at the drop of a dime. I found a tutorial where the author is able to get a permanent IP. He uses VMware Fusion as his VMachine, which is the only difference between his setup and mine. By running the terminal command "ifconfig vmnet1" he gets: a secret IP the virtual machine uses to talk to OSX And that doesn't change - which is awesome. I'm assuming it exists even if he's offline. His tutorial is here, http://bit.ly/U2lq It would be pretty fantabulous if I could replicate this with virtualBox. Anyone have ideas? Thanks:)

  Read the article

• SVNParentPath directory authorization

  - by James

  The question is a bit stupid but I can't get it sorted. I have a server with SVN that uses the SVNPath directive in httpd.conf and all works fine with path authorizations. Now I'm installing a second serer where I'm going to use SVNParentPath directive and I've got it all running except I can't get the authorization part quite right. From what I understand it's the same as when you use SVNPath but you need to specificy the repo name before the folder name.. My SVNParentPath is /srv/svn/ and I created a directory /srv/svn/testproj and then ran svnadmin create /srv/svn/testproj Now i'm configuring my authorization file: [/] * = svnadmin = rw adusgi = rw [testproj:/svn/testproj] demada = rw degari = rw scarja = rw Now if I try to commit /svn/testproj using user svnadmin or adusgi all is fine. If I try for example demada it doesn't work... (I've run the htpasswd2 commands for the user obviously. The directory is correct or atleast thats how I use the directory with the SVNPath server thats already running, the part I think I'm getting wrong is the repo name, I just used the directory name but what am I really supposed to put there?? Thank you, James

  Read the article

• Active directory Kerberos OSX problems

  - by Temotodochi

  I'll try to keep this short, but informative. I'm currently unable to bind OSX lion (10.7.4) machines to our AD. OSX kerberos (heimdal) is unable to locate the KDC service. However i can bind linux & windows machines to the AD without any problems in the same network AD controls the domain DNS and all the relevant _kerberos._tcp.x.domain.com and _kpasswd SRV DNS records are there and resolve fine when tried from OSX machines. Defined ports are open for service and manually accessible from OSX. When i try kinit in the OSX, i can get the first auth through (wrong passwords fail instantly), but when supplied with correct password, kinit fails after some waiting with "unable to reach KDC". All machines run NTP and have correct time. During testing, network is not firewalled between the machines Linux and windows machines have no problems whatsoever I have tried with and without /etc/krb5.conf - OSX by default does not need it in the krb5.conf i used a working config from one of our linux machines. dsconfigad fails with simple "connection failed to the directory server" I'm a bit baffled with this. OSX is like the KDC is nowhere to be found and at the same time my test machines with windows 7 and some linux (centos 6 & debian 6) machines have no problems whatsoever. Same network, same configurations. I'm missing some vital piece of configuration somewhere, and i can't find out what it is.

  Read the article

• X11 performance problem after upgrading from Centos3 to Centos5 with an ATI Rage XL

  - by Marcelo Santos

  After upgrading a computer from Centos3 to Centos5 an application that does a lot of scrolling took a very high performance hit. top tells me that X is using a lot of CPU and that was not happening before. The machine has an ATI Rage XL with 8MB and X is using the ati driver as there is no proprietary ATI driver for this board on linux. The xorg.conf: Section "Device" Identifier "Videocard0" Driver "ati" EndSection Section "Screen" Identifier "Screen0" Device "Videocard0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 Modes "1024x768" "800x600" "640x480" EndSubSection EndSection Section "DRI" Group 0 Mode 0666 EndSection A similar machine that still has Centos3 installed is able to start DRI on the X server while this one is not, this is the Xorg.0.log for the Centos5 machine: drmOpenDevice: node name is /dev/dri/card0 drmOpenDevice: open result is -1, (No such device or address) drmOpenDevice: open result is -1, (No such device or address) drmOpenDevice: Open failed drmOpenDevice: node name is /dev/dri/card0 drmOpenDevice: open result is -1, (No such device or address) drmOpenDevice: open result is -1, (No such device or address) drmOpenDevice: Open failed [drm] failed to load kernel module "mach64" (II) ATI(0): [drm] drmOpen failed (EE) ATI(0): [dri] DRIScreenInit Failed (II) ATI(0): Largest offscreen areas (with overlaps): (II) ATI(0): 1024 x 1279 rectangle at 0,768 (II) ATI(0): 768 x 1280 rectangle at 0,768 (II) ATI(0): Using XFree86 Acceleration Architecture (XAA) Screen to screen bit blits Solid filled rectangles 8x8 mono pattern filled rectangles Indirect CPU to Screen color expansion Solid Lines Offscreen Pixmaps Setting up tile and stipple cache: 32 128x128 slots 10 256x256 slots (==) ATI(0): Backing store disabled (==) ATI(0): Silken mouse enabled (II) ATI(0): Direct rendering disabled (==) RandR enabled I also tried using EXA instead of XAA and setting: Option "AccelMethod" "XAA" Option "XAANoOffscreenPixmaps" "true" uname -a Linux sir5.erg.inpe.br 2.6.18-128.7.1.el5 #1 SMP Mon Aug 24 08:20:55 EDT 2009 i686 i686 i386 GNU/Linux rpm -qa | grep xorg-x11-server xorg-x11-server-utils-7.1-4.fc6 xorg-x11-server-sdk-1.1.1-48.52.el5 xorg-x11-server-Xvfb-1.1.1-48.52.el5 xorg-x11-server-Xnest-1.1.1-48.52.el5 xorg-x11-server-Xorg-1.1.1-48.52.el5 The drmOpenDevice error continues when using the suggested Option "AIGLX" "true".

  Read the article

• Why do I get a DegradedArray event with mdadm

  - by azera

  Hello Just so we're clear on what's happening: I bought 4 new sata 2 drives, with the intent of using them in a raid5 all drive are fully recognised by both my bios and my linux box (gentoo) I created a raid5 array, fiddled a bit with it to understand how it works, how to monitor ect At some point, this triggered a degradedarray event, even though the array is brand new. I tried to stopping the array and recreating a new array with the same drive but the new array starts degraded too. here is what I used to create it mdadm --create -l5 -n4 /dev/md/md0-r5 /dev/sdb /dev/sdd /dev/sde /dev/sdf here are the output from my /proc/mdstat and mdadm --detail --scan **mdstat** Personalities : [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md127 : active raid5 sdf[4] sde[2] sdd[1] sdb[0] 4395415488 blocks level 5, 64k chunk, algorithm 2 [4/3] [UUU_] [>....................] recovery = 2.8% (41689732/1465138496) finish=890.3min speed=26645K/sec unused devices: <none> **detail** ARRAY /dev/md/md0-r5 metadata=0.90 spares=1 UUID=453e2833:81f22a74:64188b84:66721085 As such I have a couple questions: does a raid5 array always start in degraded mode at first ? why does sdf have the number 4 between bracket instead of 3, why does it see a spare disk and why is the 4th drive marked with _ instead of U ? (bad configuration ?) How can I recreate the array from scratch, do i have to format each drive on its own before recreating it ? Thanks for any help, I'm not sure about what I should do at the moment

  Read the article

• Passenger not booting Rails App

  - by firecall

  I'm at the end of ability, so time to ask for help. My hosting company are moving me to a new server. I've got my own VPS. It's a fresh CentOS 5 install with Plesk 9.5.2 Essentially Passenger just doesnt seem to be booting the Rails app. It's like it doesnt see it's a Rails app to be booted. I've got Rails 3.0 install with Ruby 1.9.2 built from source. I can run Bundle Install and that works. I've currently got Passenger 3 RC1 installed as per here, but have tried v2 as well. My conf/vhost.conf file looks like this: DocumentRoot /var/www/vhosts/foosite.com.au/httpdocs/public/ RackEnv development #Options Indexes I've got a /etc/httpd/conf.d/passenger.conf file which looks like this: LoadModule passenger_module /usr/local/lib/ruby/gems/1.9.1/gems/passenger-3.0.0.pre4/ext/apache2/mod_passenger.so PassengerRoot /usr/local/lib/ruby/gems/1.9.1/gems/passenger-3.0.0.pre4 PassengerRuby /usr/local/bin/ruby PassengerLogLevel 2 and all I get is a 403 forbidden or the directory listing if I enable Indexes. I dont know what else to do! Yikes. There's nothing in the Apache error log that I can see. The new server admin isnt much help as I think he's a bit junior and says he doesnt know about Rails... sigh :/ I'm a programmer and server admin isnt my bag :(

  Read the article

• Sniffing at work- How to detect

  - by coffeeaddict

  Because of the place I work has some real issues (people) especially in IT and the owner, I wonder if we are being sniffed. Is there any way to tell if on a Vista 64-bit machine: 1) In system logs some identification that would tell me that someone might log into my PC such as an Admin 2) Something in the logs that would give me a flag about maybe I'm being monitored some other way? 3) How can I be sure that my gmail, hotmail, and chat is not being sniffed. I know there are things like Simp, etc. I'm talking about specific hidden system signs either in registry or logs. Obviously I'm not going to raise any suspicion by me asking our network admin. I don't trust anyone at this company. is there a good way to basically monitor for this as an end user? Could someone log in and basically watch me work and if so, would there be any goodies left behind for me to find out if this has happened other than visual signs which would not be present...maybe some running processes?

  Read the article

• How to get gigabit network speeds on Windows XP?

  - by JB

  We've just installed gigabit switches at work, and things on the Linux side are going well. Our linux boxes, which use a Intel Corporation 82566DM-2 Gigabit nic (according to lspci), consistently get over 900 mbits/sec: iperf -c ipserver ------------------------------------------------------------ Client connecting to ipserver, TCP port 5001 TCP window size: 16.0 KByte (default) ------------------------------------------------------------ [ 3] local 192.168.40.9 port 39823 connected with 192.168.1.115 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 1.08 GBytes 929 Mbits/sec We have a bunch of Windows XP 64-bit machines that use Broadcom NetXtreme 57xx cards. I spent around a day trying to get equivalent speeds on them, but couldn't get above 200 Mbits/sec. I noticed the Windows iperf tests said that the TCP window size was 8 Kb by default (as opposed to 16 Kb on Linux, so I modified my test to reflect that. Still no love. I went to Broadcom's site, downloaded the latest drivers for the card and installed. Still no love. However, finally, I tried a 64 Kb window size with the new drivers, and finally an improvement! $ iperf -c ipserver -w64k ------------------------------------------------------------ Client connecting to ipserver, TCP port 5001 TCP window size: 64.0 KByte ------------------------------------------------------------ [ 3] local 192.168.40.214 port 1848 connected with 192.168.1.115 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 933 MBytes 782 Mbits/sec Much better, but still not really taking advantage of the full capabilities of the network. If the Linux box can reach 950 Mbits/sec consistently, this box should be able to as well. Also, if you're wondering about the medium, this is over the same cable...I'm switching back and forth. Any suggestion or ideas would be really welcome. Thanks!

  Read the article

• Failed to su after making a chroot jail

  - by arepo21

  On a 64 bit CentOS host I am using script make_chroot_jail.sh to put a user in a jail, not permitting it to see anything expect it's home at /home/jail/home/user1. I did it typing this: sudo ./make_chroot_jail.sh user1 after, when trying to connect to user1 first i was getting an error like: /bin/su: user guest does not exist i have fixed this by copying some missed libraries: sudo cp /lib64/libnss_compat.so.2 /lib64/libnss_files.so.2 /lib64/libnss_dns.so.2 /lib64/libxcrypt.so.2 /home/jail/lib64/ sudo cp -r /lib64/security/ /home/jail/lib64/ But now, when trying to connect to user1 typing su user1 and then typing it's password, i am getting this error: could not open session So the question is how to connect to user1 in this situation? P.S. Here are the permissions of some files, this might be helpful in order to provide a solution: -rwsr-xr-x 1 root root /home/jail/bin/su drwxr-xr-x 4 root root /home/jail/etc -rw-r--r-- 1 root root /home/jail/etc/pam.d/su -rw-r--r-- 1 root root /home/jail/etc/passwd -rw------- 1 root root /home/jail/etc/shadow UPDATE1 After some modifications i managed to connect to user1, but the session closes immediately! I guess this a PAM issue, however cant find a way to fix it. Here the log entry for close action from /val/log/secure: Oct 6 15:19:42 localhost su: pam_unix(su:session): session closed for user user1 What makes the session to exit immediately after launching?

  Read the article

< Previous Page | 574 575 576 577 578 579 580 581 582 583 584 585  | Next Page >