Search Results

Search found 18121 results on 725 pages for 'support esemenyek'.

Page 578/725 | < Previous Page | 574 575 576 577 578 579 580 581 582 583 584 585  | Next Page >

  • Data recovery on a corrupted 3TB disk

    - by Mark K Cowan
    Short version I probably need software to run a deep-scan recovery (ideally on Linux) to find files on NTFS filesystem. The file data is intact, but the references are no longer present. Analogous to recovering data from a "quick-formatted" partition. Hopefully there is a smarter way available than deep-scan, one which would recover filenames and possibly paths. Long version I have a 3TB disk containing a load of backups. Windows 7 SP1 refused to detect the disk when plugged in directly via SATA, so I put it on a USB/SATA adaptor which seemed to work at first. The SATA/USB adaptor probably does not support disks over 2.2TB though. Windows first asked me if I wanted to 'format' the disk, then later showed me most of the contents but some folder were inaccessible. I stupidly decided to run a CHKDSK on my backup disk, which made the folders accessible but also left them empty. I connected this disk via SATA to my main PC (Arch Linux). I tried: testdisk ntfsundelete ntfsfix --no-action (to look for diagnostically relevant faults, disk was "OK" though) to no avail as the files references in the tables had presumably been zeroed out by CHKDSK, rather than using a typical journal'd deletion). If it is useful at all, a majority of the files that I want to recover are JPEG, Photoshop PSD, and MPEG-3/MPEG-4/AVI/MKV files. If worst comes to worst, I'll just design my own sector scanner and use some simple heuristic-driven analysis to recover raw binary blocks of data from the disk which appears to match the structures of the above file types. I am unfamiliar with the exact workings of NTFS but used to be proficient at recovering FAT32 systems with just a hex-editor, so I can provide any useful diagnostic information if you let me know how to find it! My priorities in ascending order of importance for choosing the accepted answer: Restores directory structure Recovers many filenames in addition to the file data Is free / very cheap Runs on Linux Recovers a majority of file data The last point is the most important, but the more of the higher points you match the more rep you'll probably get :)

    Read the article

  • How do I make dnsmasq serve IP addresses via IPoIB?

    - by Matt
    I have a cluster farm that I'm setting up. The nodes (computers in the farm) are connected via ethernet & IP over Infiniband. I'm needing to netboot the nodes and thought dnsmasq would fit well as it provides all the features including support for DHCP over IB and it works great for our ethernet setup. However, I can't seem to get it to provide IP addresses to the infiniband adaptors on the nodes. Each node is running an Ubuntu desktop 12.04 LTS. The dnsmasq server is running on ubuntu server 12.04LTS and has the following test config: dhcp-authoritative domain-needed bogus-priv expand-hosts no-hosts domain=local dhcp-range=eth0,10.0.0.10,10.0.0.255,12h dhcp-option=eth0,3,10.0.0.1 dhcp-range=ib0,10.1.1.10,10.1.1.255,12h dhcp-option=ib0,3,10.1.1.1 log-queries log-dhcp IPoIB works between nodes when configured statically but not with dhcp. On the nodes the file /etc/network/interfaces contains auto lo iface lo inet loopback auto ib0 iface ib0 inet dhcp #iface ib0 inet static #address 10.1.1.5 #netmask 255.0.0.0 up echo connected >`find /sys -name mode | grep ib0` Is there something I need to do on the client or server end to make this work?

    Read the article

  • Why is windows 7 rejecting my key?

    - by acidzombie24
    I'm extremely confused. I have a genuine key and CD (I can take photos) and I am trying to install windows on my new tower. I believe this would be the 3rd PC i installed it (old, laptop now new tower). However i did change the HDD once but i doubt windows would think its a different computer bc of that. After going through phone activation it said i installed it on to many pcs..... i'm extremely confused. I'll be happy to deactivate it off my old tower if i knew how. I already grabbed all the files off of it. I tried to look up the amount of boxes i can install windows home premium on and found this http://en.wikipedia.org/wiki/Windows_7_editions What stuck out was this Maximum physical CPUs supported[40] 1 1 1 2 2 2 My new tower has 4cores (its the intel i7) but has two threads each so it sees 8. Does that have anything to do with this? But apparently ultimate supports '2'. I'm sure windows support more than 2 cpus so... what gives? Actually its physically one CPU so i guess the number of cores doesn't matter? Why is windows 7 rejecting my key?

    Read the article

  • Windows Server 2008 R2 install reboots unexpectedly during "Completing installation" phase

    - by knda
    I am attempting to install Windows Server 2008 R2 onto a Cisco UCS C201 M2 rack mounted server but am having major difficulties and wondering if anyone has some insight or items they could recommend for me to look at to get this one resolved. Installation is being attempted via the Cisco remote console (using CIMC's Virtual dvd-rom).. following the first phase of Setup where the installation files are copied to the target hard drive, then a reboot occurs to load Setup from the HDD, mid-way in the "Completing Installation" phase the system then reboots unexpectedly. System configuration Cisco UCS C201 M2 (2RU rack mounted server) 16GB RAM, 2x 73GB 15K SAS, 4x 300GB 10k SAS Add-on cards - Intel quad-port GigE card (no fibre channel cards) Storage - LSI MegaRAID SAS 9261-8i. onboard SATA is disabled (no SATA drives connected) KVM - Belkin No physical DVD-ROM.. :( I have... Run memtest86+, no RAM faults Disabled/enabled SATA support (BIOS) Attempted install from USB DVD-ROM, no effect Attempted unattended install scripted via Cisco Configuration Manager DVD provided Removed Belkin KVM in case that was causing drama Discovered that the Cisco website is "awesome" for searching for PDFs/Drivers cough, reverted back to Google Downloaded latest LSI drivers from LSI's site and used during Server 2008 install checked Windows ISO against checksum's from MS site checked Windows ISO by using it for an install in a VM Running out of ways to troubleshoot this as I am not sure how to enable any sort of 'verbose' mode during the setup process. Next step I have planned is to remove the Intel NIC and try the installation again.. Edit: Problem was the "Cisco INTEL QUAD PT GBE" (1000/PT) .. will have to see if this card is faulty or if it's just drivers.. thanks for the help.

    Read the article

  • Mac OS X printing to CUPS - More intuitive authentication failure?

    - by Moduspwnens
    We have a network-wide CUPS server that offers authenticated printer access to all our campus users. We've been pretty disappointed with the way Mac clients handle bad printing authentication, though. In any other authentication dialog, when a user types in a bad username or password, the window shakes briefly, allowing the user to re-enter. With printers, this isn't the case. It'll happily accept (and even save to the keychain, if specified) bad credentials. The authentication dialog is dismissed, and the user then has to deal with the print jobs showing up as "On hold (authentication required)". To get their job printed, they need to select it in the printer's queue, click "Resume", then re-enter appropriate credentials. Is there a way to get failed printing authentication to work more intuitively for Mac OS X clients? We're trying to support a BYOD environment, but our end users have been really confused by this. It's made even worse by the way it pre-populates the user's full login name (e.g. "Smith, John"), which tends to make them think to use their local machine passwords.

    Read the article

  • Keep-Alive header not sent from Tomcat 5.5 http connector?

    - by Codek
    We're currently using a hardware load balancer, which then goes to Apache and that then goes to Tomcat 5.5 via the AJP connector. We've decided to dump apache for various reasons - In our current system it doesnt provide any advantage. However when I look at the headers sent when we do this, the "Keep-Alive: timeout=15 max=96" header doesnt get sent when you use the tomcat http connector Interestingly, i can find no documentiation on "keepalivetimeout" for tomcat5.5, but i can for tomcat6. But neither can i find evidence that tomcat5.5 doesnt support this setting. here's my connector: <Connector port="8090" maxHttpHeaderSize="8192" maxThreads="400" minSpareThreads="150" maxSpareThreads="300" enableLookups="false" connectionTimeout="2" maxKeepAliveRequests="400" disableUploadTimeout="true" /> So; Is there any way I can specify the keepalive timeout if we use the http connector with tomcat 5.5, and force this header entry to be sent? Just to be clear - the exact header entry i see back from the server is this with apache: Keep-Alive: timeout=2, max=100 But nothing from tomcat/coyote. I've looked at this some more, and I dont think the Keep-Alive header entry really matters. The problem seems to be that keep-alives are simply not supported in tomcat 5.5 http connector? They do seem to work in tomcat6 (+java 6). Thanks, Dan

    Read the article

  • cisco 2900xl - SNMP - Get mac address of device connected to an interface

    - by ankit
    Hello all, Basically what i want to do is to find out what is the mac address of a device plugged in to an interface on the switch (FastEthernet0/1 for example) reading through the switch documentaion i found out that i can configure snmp trap on it to make it notify of any new mac address the switch detects by using the command snmp-server enable traps mac-notifiction but for some reason my switch does not support this feature. the only options i see are CORE_SWITCH(config)#snmp-server enable traps ? c2900 Enable SNMP c2900 traps cluster Enable Cluster traps config Enable SNMP config traps entity Enable SNMP entity traps hsrp Enable SNMP HSRP traps snmp Enable SNMP traps vlan-membership Enable VLAN Membership traps vtp Enable SNMP VTP traps <cr> so the other way would be for me to run a cronjon on my gateway to poll the switch periodically using snmp to get new mac addresses i have looked everywhere but cant seem to find the OID that would provide me this information. any help i can get would me very much appreciated ! here's the output from "show version" on my switch Cisco Internetwork Operating System Software IOS (tm) C2900XL Software (C2900XL-C3H2S-M), Version 12.0(5.4)WC(1), MAINTENANCE INTERIM SOFTWARE Copyright (c) 1986-2001 by cisco Systems, Inc. Compiled Tue 10-Jul-01 11:52 by devgoyal Image text-base: 0x00003000, data-base: 0x00333CD8 ROM: Bootstrap program is C2900XL boot loader CORE_SWITCH uptime is 1 hour, 24 minutes System returned to ROM by power-on System image file is "flash:c2900XL-c3h2s-mz.120-5.4.WC.1.bin" cisco WS-C2912-XL (PowerPC403GA) processor (revision 0x11) with 8192K/1024K bytes of memory. Processor board ID FAB0409X1WS, with hardware revision 0x01 Last reset from power-on Processor is running Enterprise Edition Software Cluster command switch capable Cluster member switch capable 12 FastEthernet/IEEE 802.3 interface(s) 32K bytes of flash-simulated non-volatile configuration memory. Base ethernet MAC Address: 00:01:42:D0:67:00 Motherboard assembly number: 73-3397-08 Power supply part number: 34-0834-01 Motherboard serial number: FAB040843G4 Power supply serial number: DAB05030HR8 Model revision number: A0 Motherboard revision number: C0 Model number: WS-C2912-XL-EN System serial number: FAB0409X1WS Configuration register is 0xF thanks, -ankit

    Read the article

  • Which IP should I use for my nameserver

    - by Luke Bream
    Sorry to ask whats probably very obvious question. I have just got a new server that is fantastically cheap but unfortunatly doesnt come with any technical support and Im very out of my depth ! My hosting company has provided the following information... Below you will find your additional IP addresses added to the server 5.9.36.51 Please note that you can use the subnet only for this server. IP: 5.9.225.64 /27 Mask: 255.255.255.224 Broadcast: 5.9.225.95 Useable IP addresses: 5.9.225.65 to 5.9.225.94 It has cPanel with WHM and im going through the setup... I have a number of questions... my domian is purchased from godaddy and I want to use it as the name server. Question 1: Which IP or IP's do I enter into the godaddy interface for ns1.mydomian.com ns2.mydomain.com Question 2: In the WHM nameserver setup what do I enter for... Please enter an IP address for each of your nameservers. ns1.mydomain.com ?????? ns2.mydomain.com ?????? Add "A Entries" for Hostname IP for Entry: ????????? Thanks for aany help you can give Luke

    Read the article

  • Cheapest iSCSI SAN for Windows 2008/SQL Server clustering?

    - by MichaelGG
    Are there any production-quality iSCSI SANs suitable for use with Windows Server 2008/SQL Server for failover clustering? So far, I've only seen Dell's MD3000i, and HP's MSA 2000 (2012i), which both are around $6K with a minimal disk configuration. Buffalo (yea, I know), has a $1000 device with iSCSI support, but they say it will not work for 2008 failover clustering. I'm interested in seeing something suitable for failover in a production environment, but with very low IO requirements. (Clustering, say, a 30GB DB.) As for using software: On Windows, StarWind seems to have a great solution. But it's actually more money than buying a hardware SAN. (As I understand, only the enterprise edition supports having replicas, and that's $3000 a license.) I was thinking I could use Linux, something like DRBD + an iSCSI target would be fine. However, I haven't seen any free or low-cost iSCSI software that supports SCSI-3 persistent reservations, which Windows 2008 needs for failover clustering. I know $6K isn't much at all, just curious to see if there are practical cheaper solutions out there. And finally, yes, the software is expensive, but many small business get MS BizSpark, so the Windows 2008 Enterprise / SQL 2008 licenses are completely free.

    Read the article

  • Windows 2008 Standard upgrade to Windows 2008 Enterprise failure

    - by Archit Baweja
    Sidestory, I was in the process of setting up a second Exchange 2010 server for DAG support, when I realized that my box needed Windows 2008 Enterprise edition. The box currently has Windows 2008 Standard Windows update including SP2 Exchange 2010 with CAS, HT, Mailbox roles Domain Services role File Services role. When I try to upgrade to Windows 2008 Enterprise, I initially got a "your current version of windows is more recent than the intallation media", something to that effect. My first guess was it may be SP2 related, so I uninstalled SP2, restarted and tried again. This time it gave me an error to the effect Windows could not configure one or more windows components. Please restart and try the update again. This was at the last stage of the Windows 2008 Enterprise install when it says "Completing installation". So I removed Domain Services role (including demoting it as a DC). However I get the same error again. Anyone see something like this before and have any suggestions? Also , is there a log file the windows upgrade program spits out that I can consult to see what component exactly is interfering? Update 1 Based on some googling I finally found the setup log file, and it seems that Windows setup had an issue determining the .Net 3.0 "feature" being installed or uninstalled. So based of of a win7/vista technet article I'm going to retry the upgrade after removing the .Net 3.0 feature.

    Read the article

  • Hyperic HQ- Monitor process statistics for 50+ processes on Linux machine

    - by Chris
    Is there an easy way to get metrics on all processes that start with the letters XYZ? I have about 80 processes that I have to monitor individually that all start with the prefix XYZ. I have created a query using the sigar shell: ps State.Name.sw=XYZ, which will give me a list of the processes that I want. What I need to do is define this list of processes through said query and collect and track statistics from the Process service: http://support.hyperic.com/display/hypcomm/Process+service What I need is 3 or 4 key statistics for each of the XYZ processes defined by my query to show up as graphs in the web front end. Note: Hyperic HQ server is installed on a windows machine and I'm monitoring a Linux box via an agent. Thanks, Chris Edit: Here is my try at a plugin that may give me what I want, but it's not being inventoried/detected by the Hyperic web UI. Simply pointing me to one of Hyperic's tutorials won't do. Thanks. <!DOCTYPE plugin [ <!ENTITY process-metrics SYSTEM "/pdk/plugins/process-metrics.xml">]> <plugin> <server name="ABCStats"> <config> <option name="process.query" description="Process Query" default="State.Name.sw=XYZ"/> </config> <metric name="Availability" alias="Availability" template="sigar:Type=ProcState,Arg=%process.query%:State" category="AVAILABILITY" indicator="true" units="percentage" collectionType="dynamic"/> &process-metrics; <plugin type="autoinventory"/> <plugin type="measurement" class="org.hyperic.hq.product.MeasurementPlugin"/> </server> </plugin>

    Read the article

  • setting up a proxy to mirror an SSH SOCKS connection

    - by aresnick
    I have two remote machines, remote1 and remote2. remote2 is only running sshd, and I can't run anything else on it. remote1 is a full-fledged server to which I have complete access. I can run a SOCKS proxy on remote2 via ssh -f -N -D *:8080 me@remote2 which lets me expose a SOCKS proxy on port 8080 on remote1. I'd like to authenticate this so that the proxy isn't sitting open. How can I do this? It seems like I should be able to use delegate, but I can't even seem to get its HTTP proxy functionality working. When I run delegated -r -P8081 SERVER=http PERMIT="*:*:*" REMITTABLE="*" I can't even get it to work on port 8081. Anyway, I was hoping someone could point me in the right direction to let me authenticate access to the SOCKS proxy connection? That is, I want to be able to point my browser's proxy at remote1 and browse the internet through the SSH SOCKS proxy/tunnel to remote2. squid doesn't support a SOCKS parent =( Thanks!

    Read the article

  • Can't get an IBM xSeries 345 server to load Windows Server 2003 using ServerGuide utility

    - by Kyle Noland
    I have a client that has an IBM xSeries 345 eServer. Per the IBM support website, I have downloaded the ServerGuide Setup 7.4.17 installation ISO and burned a bootable CD. The CD boots fine and loads the utility. I walk through the following screens without any issue: Set the date and Time Detect the IBM ServeRAID card and install the latest firmware Clear the hard disks Set up the RAID array The next step is format the NOS partition. I select my partition size and the utility goes through the following steps: Creating NOS partition Formatting NOS partition (NTFS) Copying W32 files The copying W32 files takes about 10 minutes. I see the CD drive and disks working hard. When the copying is complete, I'm taken to a blank page just NOS Partitioning at the top. At the bottom of the screen are the familiar Back and Exit buttons. I see the place where the Next button should be, and if I click on it I can tell there is something there, but the space is empty. No button is displayed and clicking the empty spot doesn't ever take me to the next screen. I can't load the OS until I get past this part. I have already tried: Burning multiple copies and versions of the ServerGuide CD Letting the final screen just sit there over the weekend thinking it might advance after syncing the drives or something Has anybody else seen this? I'm really at a loss here.

    Read the article

  • How to disable auto insert notification in Windows 7?

    - by White Phoenix
    Alright, here's the problem. My hard drive activity light on my custom built PC is blinking exactly once every second. Microsoft has this to say on the issue: http://support.microsoft.com/kb/138598 There has been discussion on this issue several months ago: Why does my hard drive LED light blink every second? The problem seems to stem from primarily Windows 7 polling the CD-ROM/DVD drive every second to see if something is inserted. The Windows 7 users in the thread that was linked in the superuser question, https://social.technet.microsoft.com/Forums/fi-FI/w7itprohardware/thread/4f6f63b3-4b58-4154-9298-1566100f9d00, have confirmed that this IS a known issue with Windows 7. Some people point at the motherboard circuitry causing the CD-ROM and SATA activity to both be linked to that hard drive activity, but whatever the case, the temporary solution seems to be to disable the CD/DVD-ROM drive in Device Manager. In fact, disabling the CD/DVD-ROM does stop the blinking, but of course this solution is counterproductive, because I shouldn't have to entirely disable a device to fix this problem. I've done the following suggestions in that thread: Change the autorun registry entry to 0 Completely disable autoplay in the autoplay control panel Disable autoplay in the Local Group Policy Editor. None of these stop the blinking from happening - apparently these solutions work for both XP and Vista, but it seems to be different in Windows 7. So I'm wondering if anyone has found out how to completely disable the polling in Windows 7, or if this will just have to be an issue we will have to deal with. There's no option to disable the auto insert notification when you go to the device within device manager (there was in XP), so I got no idea where this option is hidden, or if there's a registry key entry I could change to stop the polling. Anyone have any idea?

    Read the article

  • Two large, linked Excel files take 30 minutes to save, except in VMWare environment

    - by Gerald L
    I support some tax consultants who love to use Excel when they should probably be using Access. Anyway, they have created two Excel files, A and B. File B has cells linked to file A. File A is 27 MB and file B is 16 MB. One worksheet has roughly 1 million rows and there is another worksheet doing a whole bunch of SUMIF on the 1 million rows. Not the best idea, but whatever. Both Excel files open and recalculate within a reasonable amount of time (1-2 minutes). For a files that large, this is acceptable. Here is the problem: Once you change a cell, and save the file B, it takes a solid 30 minutes to save the file, and the processors are going full speed. I've tried this on 6 different machines, all running Windows XP SP3 with Office 2007 SP2 and all patches. The specs vary from one machine with 512 MB or RAM to a machine with 4 GB of RAM and quad processors. Same result every time. Here is the clincher: If I do this same save operation on a VMWare virtual machine, the file gets saved in 1 minute. I've tried this with my ESX servers at the office, my Mac Fusion at home, and VMWare workstation at the office. It does not matter how much RAM the virtual machine has... it saves in about 1 minute every time. Does anybody have any idea why this is happening and how to fix?

    Read the article

  • Join ActiveDirectory (Win 2k8R2) to OpenDirectory(Snow Leopard)

    - by Tom O'Connor
    The vast majority of questions and so on regarding the interoperability of Active and Open directories involves getting Mac clients to see an AD and auth against it. What we'd like to do is get a Windows 7 workstation to auth completely against Open Directory. We tried setting it up as an NT4 type PDC, and that doesn't work satisfactorily. We tried using pGina and the LDAP backend, which allows Authentication, but has no support for Authorization, and as a result, if we mount an NFS Share, the user has the rights to do anything they damn well please. Not ideal for security (Totally bloody unacceptable, actually). We tried using a Samba server (newer version than on the Open Directory Server) as an intermediate, so that it knows about the LDAP server on the OD Server, but uses Samba 4 instead of v3. That didn't work either. We could login, but couldn't mount, and if we did, we had the same rights as with pGina. If we right-click the mounted drive in Windows, and have a look at NFS UID, it returns -2, not the correct (mapped) UID. So the final plan I've got is to use an Active Directory, inside a Windows 2008R2 Virtual Machine. What I want to achieve is to have the Active Directory sync it's user data from OpenDirectory (read-only would be fine). That way, we'd have the ability to connect Windows 7 clients to a "virtual domain" which would actually just grab information from OD's LDAP. All the information I've found is about how to go the other way. Does anyone know how we can do this?

    Read the article

  • samba4 dc "network location cannot be reached"

    - by mitchell babies peters
    to clear the air centos 6.4? (maybe 6.3) as the server, running samba 4.0.10, trying to add a windows 7 client that has connectivity to the server. this is what windows shouts as me as it mocks my dependence on network infrastructure. "the network location cannot be reached." i have access to the domain contoller (dc) im using the dc as the domain name server (dns) already, and the name is correctly resolving, and it is correctly forwarding outbound traffic. i have nothing but self taught experience with active directory(ad) so if i am missing something obvious, please shout it out, but keep the verbal abuse to a minimum. i checked samba4DC + my error and found nothing relevant to my issue, if i missed something please point me in that direction. the weekend is just starting as i write this so i probably wont be back on to check this post for a day or three, but i might because this mystery is killing me. i followed the samba4 as a dc guide here and i supplimented gaps with this i have tested kerberos, ntp, and set my DC as the clock to sync to in my windows client and it appears to be a very small fraction of a second off so that shouldn't be it. also, firewall and selinux are both off for testing. i have also tried disabling ipv6, and cleared the registry of ipv6 records (allegedly the default samba4 as a DC runs as windows server 2003 which allegedly does not support or tolerate the existence of ipv6, fair warning, i heard this on the internet so it is probably a lie) i have tried a few other things that i have forgotten because i have been doing this for a day and a half now. ideas welcome. suggestions for alternatives are also welcome, as long as they are free. i was given a budget of $0 dollars and told to implement active directory (no prior knowledge of active directory at that point).

    Read the article

  • NetApp NDMP backup with BE 2010 R2 works, restore fails

    - by uuwe
    Hi, I'm having some issues with a new Backup Exec 2010 R2 installation. I configured a NetApp FAS2020 as an NDMP device and want to backup files from the NAS to a tape drive connected to my backup server. I set up ndmpd according to this document (http://www.symantec.com/business/support/index?page=content&id=TECH48957) and created a separate backup user (http://filers.blogspot.com/2006/09/setting-veritas-netbackup-with-non.html). Backup works perfectly, but restoring any file gives me an authentication failed error. The NDMP device has a "global" ndmp user configured in the device tab (tried this with the newly created ndmpd backup user and the netapp root) and I can also configure separate resource credentials in the BE restore job. I have tried setting the same accounts for the "global" ndmp device and the restore credentials and have also tried setting different accounts for them. NDMP debug level is at 5 and this is what shows up in /etc/messages. The session is closed immediately after it has been granted. 16:12:07 PST [Java_Thread:info]: ndmpdserver: ndmpd.access allowed for version = 4, sessionId = 51, from src ip = 192.168.11.17, dst ip = FAS2020-1/192.168.11.75, src port = 50857, dst port = 10000 16:12:07 PST [Java_Thread:info]: Ndmpd51: ndmpd session closed successfully for version = 4, sessionId = 51, from src ip = 192.168.11.17, dst ip = FAS2020-1/192.168.11.75, src port = 50857, dst port = 10000 Running wireshark on the backup server doesn't produce much. It shows a SYN - SYN/ACK - NDMP CONNECT_CLOSE Request from the backup server. The Resource Credentials for the restore job behave very oddly. If I enter NDMP credentials and do "Test All" it fails. If I use my regular domain backup account, it is successful. There are no failed or succeeded logons in the NetApp ndmp log and tracing this check shows that it doesn't even connect to the NAS. This makes me think that this is more likely flaky BE behaviour rather than misconfiguration of the NAS. Here is the options ndmp output: FAS2020-1 options ndmp ndmpd.access all ndmpd.authtype challenge ndmpd.connectlog.enabled on ndmpd.enable on ndmpd.ignore_ctime.enabled off ndmpd.offset_map.enable on ndmpd.password_length 16 ndmpd.preferred_interface disable ndmpd.tcpnodelay.enable off

    Read the article

  • Apache wont start after attempting to install SSL

    - by yummm
    Below is what my VirtualHosts look like in httpd.conf <VirtualHost *:80> # Admin email, Server Name (domain name) and any aliases ServerAdmin [email protected] ServerName mydomain.com ServerAlias www.mydomain.com # Index file and Document Root (where the public files are located) DirectoryIndex index.php DocumentRoot /home/mydomain/public_html/mydomain.com/public # Custom log file locations LogLevel warn ErrorLog /home/mydomain/public_html/mydomain.com/log/error.log CustomLog /home/mydomain/public_html/mydomain.com/log/access.log combined </VirtualHost> <VirtualHost *:443> SSLEngine on SSLCertificateFile /etc/httpd/conf/ssl.crt/mydomain.com.crt SSLCertificateKeyFile /etc/httpd/conf/ssl.key/mydomain.com.key ServerName mydomain.com DirectoryIndex index.php DocumentRoot /home/mydomain/public_html/mydomain.com/public </VirtualHost> I'm using the latest version of Apache on CentOS and there isn't any error being generated. Apache just will not start. Any ideas what I'm doing wrong? UPDATE - Found these messages in the error log: [Tue Mar 16 02:07:57 2010] [error] Init: Private key not found [Tue Mar 16 02:07:57 2010] [error] SSL Library Error: 218710120 error:0D094068:asn1 encoding routines:d2i_ASN1_SET:bad tag [Tue Mar 16 02:07:57 2010] [error] SSL Library Error: 218529960 error:0D0680A8:asn1 encoding routines:ASN1_CHECK_TLEN:wrong tag [Tue Mar 16 02:07:57 2010] [error] SSL Library Error: 218595386 error:0D07803A:asn1 encoding routines:ASN1_ITEM_EX_D2I:nested asn1 error [Tue Mar 16 02:07:57 2010] [error] SSL Library Error: 218734605 error:0D09A00D:asn1 encoding routines:d2i_PrivateKey:ASN1 lib

    Read the article

  • Yum installing wrong MySQL version on CentOS 5 (Amazon)

    - by Marius Stuparu
    I'm having trouble with a CentOS server running on AWS. This is CentOS 5.6 i386 from RightImage, but the problem was the same on all RightScale AMIs. When issuing the following command: yum install mysql mysql-server mysql-devel the only packages proposed by yum are MySQL-devel-community and MySQL-server-community. Which would't be a problem, except this package is old/incomplete, because it does not create a "mysqld" service, only a /etc/init.d/mysql (notice the missing d). That would't be a problem, I can start the service by doing ./etc/init.d/mysql start, and it starts OK, but there is no "mysql" (or other mysql*) command available. If I try to force a different version (yum install mysql50-server...) I get this yum error: mysql-5.0.77-4.el5_6.6.i386 from updates has depsolving problems --> mysql conflicts with MySQL-server-community (even when I don't have MySQL-server-community installed). I have tried this before and after yum update, in a fresh image. How can I install a working version of MySQL? I'm stuck on CentOS 5 because I want to install Kloxo (which does not yet support CentOS 6). I'm not interested in Webmin, and I can't afford cPanel. Thanks!

    Read the article

  • BGP Multipath & return routes

    - by Dennis van der Stelt
    I'm probably a complete n00b concerning serverfault related questions, but our IT department makes a bold statement I wish to verify. I've searched the internet, but can find nothing related to my question, so I come here. We have Threat Management Gateway 2010 and we used to just route the request to IIS and it contained the ip address so we could see where it was coming from. But now they turned on "Requests apear to come the TMG server" so ip addresses aren't forwarded anymore. Every request has the ip of the TMG server. Now the idea behind this is that because of multipath bgp routes, the incoming request goes over RouteA, but the acknowledgement messages could return over RouteB. The claim is that because the request doesn't come from the first known source, our proxy, but instead from IIS, some smart routers at the visitor of our websites don't recognize the acknowledgement message and filter it out. In other words, the response never arrives. Again, this is the claim. But I cannot find ANY resources on the internet that support this claim. I do read about bgp multipath, but more in the case that there are alternative routes when the fastest route fails for some reason. So is the claim completely bogus or is there (some) truth to it? Can someone explain or point me to resources? Thanks in advance!

    Read the article

  • Issue with InnoDB engine while enabling and [ skip-innodb ] - [ERROR] Plugin 'InnoDB' init function returned error

    - by Ahn
    How to enable InnoDB, which was previously disabled with skip-innodb option. Case 1: Disabled the innodb with skip-innodb option and show engines givens as below. Engine | Support ... | InnoDB | NO ...... Case 2: As I want to enable the innodb, I commanded the #skip-innodb option and restarted. But now the show engines even not showing the InnoDB engine in the list. ? Mysql Version : 5.1.57-community-log OS : CentOS release 5.7 (Final) Log: 120622 13:06:36 InnoDB: Initializing buffer pool, size = 8.0M 120622 13:06:36 InnoDB: Completed initialization of buffer pool InnoDB: No valid checkpoint found. InnoDB: If this error appears when you are creating an InnoDB database, InnoDB: the problem may be that during an earlier attempt you managed InnoDB: to create the InnoDB data files, but log file creation failed. InnoDB: If that is the case, please refer to InnoDB: http://dev.mysql.com/doc/refman/5.1/en/error-creating-innodb.html 120622 13:06:36 [ERROR] Plugin 'InnoDB' init function returned error. 120622 13:06:36 [ERROR] Plugin 'InnoDB' registration as a STORAGE ENGINE failed. 120622 13:06:36 [Note] Event Scheduler: Loaded 0 events 120622 13:06:36 [Note] /usr/sbin/mysqld: ready for connections. Version: '5.1.57-community-log' socket: '/data/mysqlsnd/mysql.sock1' port: 3307 MySQL Community Server (GPL)

    Read the article

  • CD-ROM Cant Be Accessed After Installing VMware Tools on VMware Server 2.0.2

    - by Optimal Solutions
    Using VMware Server 2.02, I set up a new VM (Windows XP Pro) applied all of the updates, added Windows addons from the install CD, etc... I got it to a stable point and up through that point I was able to access the CD-ROM drive (E: on my host). What I never did before was install "VMware Tools" and since it claims to give better mouse and video support, I gave it a shot. What it does is it places the install package in a virtual CD-ROM drive. I ran the install, no errors and it wants a reboot. I log back in after reboot and pop in the install CD for Microsoft Office 2003 and I receive the message "Please Insert A Disc Into Drive D:". Drive D: would be the next logical drive after the C: drive where I chose to install the OS. The message box sits there and if I click "Cancel", to return to Windows Explorer, the status bar seems to blink ever 1/2 second - as if its polling for a CD-ROM drive or something. No bangs or exclamations in the Device Manager for any hardware. I had taken a snapshot prior to the VMware Tools install and upon restoring it, the CD-ROM is back. I made copies of two other VMs, installed the VMware Tools on those VMs and both experienced the same issues: Windows 2003 Server and Windows 7 (32-bit). Has anyone seen this issue and know of a fix for this? It would be nice to have the better graphics and better mouse control AND use my CD-ROM drive as well! Thank you.

    Read the article

  • How to install a private user script in Chrome 21+?

    - by Mathias Bynens
    In Chrome 20 and older versions, you could simply open any .user.js file in Chrome and it would prompt you to install the user script. However, in Chrome 21 and up, it downloads the file instead, and displays a warning at the top saying “Extensions, apps, and user scripts can only be added from the Chrome Web Store”. The “Learn More” link points to http://support.google.com/chrome_webstore/bin/answer.py?hl=en&answer=2664769, but that page doesn’t say anything about user scripts, only about extensions in .crx format, apps, and themes. This part sounded interesting: Enterprise Administrators: You can specify URLs that are allowed to install extensions, apps, and themes directly through the ExtensionInstallSources policy. So, I ran the following commands, then restarted Chrome and Chrome Canary: defaults write com.google.Chrome ExtensionInstallSources -array "https://gist.github.com/*" defaults write com.google.Chrome.canary ExtensionInstallSources -array "https://gist.github.com/*" Sadly, these settings only seem to affect extensions, apps, and themes (as it says in the text), not user scripts. (I’ve filed a bug asking to make this setting affect user scripts as well.) Any ideas on how to install a private user script (that I don’t want to add to the Chrome Web Store) in Chrome 21+? Update: The problem was that gist.github.com’s raw URLs redirect to a different domain. So, use these commands instead: # Allow installing user scripts via GitHub or Userscripts.org defaults write com.google.Chrome ExtensionInstallSources -array "https://*.github.com/*" "http://userscripts.org/*" defaults write com.google.Chrome.canary ExtensionInstallSources -array "https://*.github.com/*" "http://userscripts.org/*" This works!

    Read the article

  • Upgrade Debian to unstable on VirtualBox: udev problem

    - by Ken
    I'm running Debian stable on VirtualBox on Windows Vista 64-bit Ultimate. It's been running great, but I needed some newer packages, so I put sid in my sources.list to upgrade to unstable (as I've done a dozen times on various Linux boxes over the years). When I upgraded, something went screwy and it asked me to run apt-get -f install to fix them, which gave this: (Reading database ... 77846 files and directories currently installed.) Preparing to replace udev 0.125-7+lenny3 (using .../archives/udev_151-3_amd64.deb) ... Since release 150, udev requires that support for the CONFIG_SYSFS_DEPRECATED feature is disabled in the running kernel. Please upgrade your kernel before or while upgrading udev. AT YOUR OWN RISK, you can force the installation of this version of udev WHICH DOES NOT WORK WITH YOUR RUNNING KERNEL AND WILL BREAK YOUR SYSTEM AT THE NEXT REBOOT by creating the /etc/udev/kernel-upgrade file. There is always a safer way to upgrade, do not try this unless you understand what you are doing! dpkg: error processing /var/cache/apt/archives/udev_151-3_amd64.deb (--unpack): subprocess new pre-installation script returned error exit status 1 insserv: warning: current start runlevel(s) (2 3 4 5) of script `vboxadd-x11' overwrites defaults (empty). insserv: warning: current stop runlevel(s) (0 1 6) of script `vboxadd-x11' overwrites defaults (empty). insserv: warning: current start runlevel(s) (2 3 4 5) of script `vboxadd-x11' overwrites defaults (empty). insserv: warning: current stop runlevel(s) (0 1 6) of script `vboxadd-x11' overwrites defaults (empty). Errors were encountered while processing: /var/cache/apt/archives/udev_151-3_amd64.deb E: Sub-process /usr/bin/dpkg returned an error code (1) I have the VirtualBox extensions installed, and it looks like the udev install doesn't know what to make of them. But I don't know exactly where/how they're installed (I just ran the VBoxLinuxAdditions-amd64.run script, basically), so I don't know how to disable them. Any ideas? Thanks!

    Read the article

< Previous Page | 574 575 576 577 578 579 580 581 582 583 584 585  | Next Page >