Search Results

Search found 3538 results on 142 pages for 'chris reid'.

Page 58/142 | < Previous Page | 54 55 56 57 58 59 60 61 62 63 64 65  | Next Page >

• Appropriate Network switch for small server cluster

  - by Chris Dutrow

  Need to build a small business server cluster for the purpose of crunching data. It will not host a web site that needs to be available 24/7. It does need to support servers that host Redis, a Cassandra database cluster, and a Python web server. Operating system will most likely be Centos 6.4 Other servers in the cluster should be able to communicate very fast with each other, especially the Redis server. This will probably require the use of internal IP addresses. We will need to use multi-data center replication to synchronize the Cassandra cluster with the one that we currently have hosted on the cloud Was looking into network switches and we are unsure of the appropriate specifications that we should be looking for. Does the switch need to be "managed" or can it be "unmanged"? Does the switch need to support IPv6 or just IPv4? Do we need an enterprise level Cisco switch, or can we go with something like a $200 DLink managed (or unmanaged) small business switch? Thanks so much!

  Read the article

• Why does my monitor have a black screen but the power light is blinking green?

  - by Chris Vesper

  I have a ViewSonic VA912b 19" display I use as a secondary monitor. When I turn it on, the power light is green for a few seconds, and then switches to blinking green. The display stays black. Windows thinks the monitor is on, as it shows up in the control panel as a second monitor. If I unplug the DVI cable, it displays a "No Signal" message and the power light goes to amber, which means it went to sleep.

  Read the article

• VMWare Workstation can't read CD/DVD drive

  - by Chris W

  A fresh install of VMWare Workstation 7 (7.1.1 build 282343) on Windows 7 64 bit. When I try to read a CD/DVD from a guest (either to install a fresh guest or to read a CD within an existing VM I get the following error: Cannot connect virtual device ide1:0 because no corresponding device is available on the host. I've tried fiddling with the IDE channels as well as tried SCSI with no joy. What am I missing? I can run ISOs fine but I don't want to have to convert everything to an ISO when I presume that this should just work fine.

  Read the article

• Does private browsing prevent socket events?

  - by Chris Cirefice

  I usually do my work in Google Chrome (v36.0.1985.143), private browsing enabled. I use Firefox to browse Stack Exchange, in normal mode so that all my logins are persisted. Sometimes I accidentally open an SE question in Chrome, so I copy-paste the URL to Firefox and get on reading. I left the SE tab in Chrome open, and up-voted a question in Firefox. Normally, you immediately see other users' voting activity via socket event emitting (possibly Socket.IO, I don't know SE's back-end). I noticed that in my Chrome tab, I didn't see the upvote that I had cast in Firefox. I had to refresh to be able to see the vote count change. So, as the title of the question states: does private browsing prevent socket events?

  Read the article

• How can I convert an AVI file to something the iPod can view?

  - by chris

  My son received a DVD with some AVI files of his soccer game. (I think they're from a Sharp camcorder, but I'm not 100% sure of that). How can I convert them to a format that he can view on his iPod Touch? I have a Mac, Linux and Windows machines available, so any platform-specific recommendations are welcome.

  Read the article

• SQL Clustering on Hyper V - is a cluster within a cluster a benefit.

  - by Chris W

  This is a re-hash of a question I asked a while back - after a consultant has come in firing ideas in to other teams in the department the whole issue has been raised again hence I'm looking for more detailed answers. We're intending to set-up a multi-instance SQL Cluster across a number of physical blades which will run a variety of different systems across each SQL instance. In general use there will be one virtual SQL instance running on each VM host. Again, in general operation each VM host will run on a dedicated underlying blade. The set-up should give us lots of flexibility for maintenance of any individual VM or underlying blade with all the SQL instances able to fail over as required. My original plan had been to do the following: Install 2008 R2 on each blade Add Hyper V to each blade Install a 2008 R2 VM to each blade Within the VMs - create a failover cluster and then install SQL Server clustering. The consultant has suggested that we instead do the following: Install 2008 R2 on each blade Add Hyper V to each blade Install a 2008 R2 VM to each blade Create a cluster on the HOST machines which will host all the VMs. Within the VMs - create a failover cluster and then install SQL Server clustering. The big difference is the addition of step 4 whereby we cluster all of the guest VMs as well. The argument is that it improves maintenance further since we have no ties at all between the SQL cluster and physical hardware. We can in theory live migrate the guest VMs around the hosts without affecting the SQL cluster at all so we for routine maintenance physical blades we move the SQL cluster around without interruption and without needing to failover. It sounds like a nice idea but I've not come across anything on the internet where people say they've done this and it works OK. Can I actually do the live migrations of the guests without the SQL Cluster hosted within them getting upset? Does anyone have any experience of this set up, good or bad? Are there some pros and cons that I've not considered? I appreciate that mirroring is also a valuable option to consider - in this case we're favouring clustering since it will do the whole of each instance and we have a good number of databases. Some DBs are for lumbering 3rd party systems that may not even work kindly with mirroring (and my understanding of clustering is that fail overs are completely transparent to the clients). Thanks.

  Read the article

• How to pin "Visual Studio 2010 Documentation" shortcut to Windows 7 taskbar?

  - by Chris W. Rea

  I just installed Microsoft Visual Studio 2010 at home, on my Windows 7 PC. One of the items installed with VS2010 is "Microsoft Visual Studio 2010 Documentation". I like to have the documentation installed locally and at my fingertips, and so before had always added a shortcut for the help viewer to my Quick Launch toolbar. However, I'm not able to pin the new documentation to the Windows 7 taskbar. It's frustrating. Note carefully: When I launch "Microsoft Visual Studio 2010 Documentation" from the Start menu, it seems to perform two functions: First, it launches the "Help Library Agent", which is a local HTTP server from which the help content is served... similar to the local ASP.NET web development server. Second, it launches the default web browser against the localhost URL corresponding to the port on which the "Help Library Agent" is running, for example: http://127.0.0.1:47873/help/1-1444/ms.help?method=f1&query=msdnstart&product=VS&productVersion=100&locale=en-US ... in other words, the program doesn't leave behind an active foreground process that displays in the taskbar. So, I can't choose "Pin this program to taskbar" as one might do so with a typical program. How can I get a shortcut to "Microsoft Visual Studio 2010 Documentation" in the Windows 7 taskbar? Has anybody got a workaround for this?

  Read the article

• SQL Server backup/restore error: The Media Family on Device is Incorrectly Formed.

  - by Chris

  Basically, I'm having this issue: http://www.sqlcoffee.com/Troubleshooting047.htm What I'm doing is running a script I found online (http://pastebin.com/3n0ZfybL) to do a full backup, then rar'ing up the file and moving it to my computer. The CRC of the backup file inside the rar is correct on both computers, so there is no problem with data being corrupted when I transfer it. But then I go and try to restore the database on my dev computer here and I get the errors "sql server cannot process this media family" ... "msg 3013". Why is this happening? I'd test out the backup on the server I'm getting it from, but it's a production server.

  Read the article

• Iphone 3GS to laptop Syncing

  - by Chris

  I use my Iphone calender to store all my appointments and customer information etc rather than my Outlook calender on my laptop most of the time. To the best of my knowledge I have never lost any info before, but after syncing the two devices today my calender is now empty on both. I had thought that syncing would mean taking the information on both devices, amalgamating it and populating both devices with the same info? Two questions: a) Is there anyway of retrieving the lost information? (or am I sunk?) b) Is there any way of averting such disaster in the future? Whilst I suspect that "Read the manual - Idiot!" would be the correct response, any help really is greatly appreciated!

  Read the article

• A way to rename keep the first 10 charaters of a image name

  - by Chris

  Hi there, I have a very big job to do. I have about 930 pictures which are called like: 5210841 Tuinset Senator.jpg 5210898 Traptrede Premium.jpg etc. I'm looking for a way to rename these pictures, without losing the number part. So for the first one, its name would be: 5210841.jpg and the second 5210898.jpg Can you guys think about a program which can do this job? It's for a Windows platform.

  Read the article

• ASP.NET MVC hosting recommendations

  - by chris

  I'm looking for recommendations for hosting an asp.net MVC application. Obviously, we need to be able to have access to configure IIS directly - I'd prefer not to have to go thru a control panel. The web server needs to have a dedicated IP, since some clients will be accessing it via IP. We need at least a SQLServer 2005 database, ideally on the same box. Load and usage will be pretty low, so a virtual machine will probably be fine. Does any one have any recommendations that meet the above constraints?

  Read the article

• Can I use an Apple AirPort Express as a wireless-to-wired bridge?

  - by Chris

  I have a wireless network using an Apple AirPort Extreme. That device is set up in my office and hooked up to the cable modem. I have a TV in another room which can accept a wired internet connection (not wireless enabled). Can I use an Apple AirPort Express's ethernet jack to create a wireless-to-wired bridge? If not, what device would I use to do the same thing?

  Read the article

• SQL Server 2000 -- Log Shipping reliability?

  - by Chris J

  I've been asked to look into log shipping for SQL Server 2000 (yes, 2000): something in my memory tells me that I looked at this years ago and there were question marks over it's reliability. I'm trying to google stuff, but given the age of 2000 now I've put pulled up anything to confirm this -- most seem to say they're using it without problem, so just want confirm whether I'm just being delusional, or whether there were problems, but with a fully patched SP4 box these don't exist any more. Cheers!

  Read the article

• Advice for migrating email server

  - by Chris Adams

  Hi there, I'm planning to migrate a Zimbra server with about 200gb of data from a server hosted in an office into a datacentre, to increase uptime (we've had a couple of outages when our network here started flaking out, and we have people in other countries relying on this server too). However, I'm not sure how best to migrate the data into the data centre without rendering the connection unusable during office hours, because there's far too much to send in over night over the two meg upstream connection we have here. I'm familiar with using tools like nice to stop a long running process degrading machine performance - is there a simple way to throttle a connection between office hours, so the long running transfer doesn't block the pipe, but then opens up outside of office hours to make the most of the bandwidth? I'm aware the alternative here is to simply mail a hard drive to the data centre, but I'd like to avoid doing that if I could. We're using Centos Linux for our servers, in the office and the datacentre, so extra points for an open source linux answer.

  Read the article

• Options for running virtual appliance on boot in Windows

  - by Chris

  I'm working on a software package I'd like to be able to release as a virtual appliance. I'll be exporting the appliance from VirtualBox as a .ovf file. Outside of vmware server, are there any Windows host options that allow me to start the appliance when the host OS boots?

  Read the article

• Is there any way to set up a malware-blocking transparent proxy on an Airport Extreme?

  - by Chris R

  I'd like to add some kind of easily-administered transparent HTTP proxy to my home network. Ideally, it would allow me to, for example, redirect web requests to blacklisted servers into nothing, block certain kinds of content, et al. My home network at the moment consists of a mac mini media server that could -- if the load wasn't huge -- fill this role as well, an Airport Extreme, and a mac laptop that is my main machine. I'm reasonably technically savvy, so don't spare the complicated answers.

  Read the article

• Cisco IOS router config -- how to disable SSH / SNMP on all but loopback address?

  - by chris

  Sorry for the naive question; a quick reading of the cisco docs doesn't answer this question... So I've got a router (say for the sake of argument a 4500 running IOS 15.x) It has interfaces in 3 different subnets -- 10.0.0.1/24, 10.0.1.1/24, and 10.0.2.1/24 It also has a loopback address of 172.16.0.33 How do I make it so that SSH / SNMP and other administrative traffic works on the 172 address but doesn't work on the IP addresses I wish to only use for L3 forwarding? Ideally this can be done by disabling the control plane access to these interfaces not just by using an ACL, but whatever, I don't actually care that much as long as it works... Thanks!

  Read the article

• How do I get rid of com.apple.launchd.peruser errors in my log?

  - by Chris R

  I'm getting repeated errors in my console log that look (basically) like this: 10-09-29 10:06:08 AM com.apple.launchd[1] (com.apple.launchd.peruser.501[51581]) getpwuid("501") failed 10-09-29 10:06:08 AM com.apple.launchd[1] (com.apple.launchd.peruser.501[51581]) Exited with exit code: 1 This machine was set up using the migration assistant, from a machine where my UID was 501, but here it's 505. I have the same username and group set, of course, but... So, where is this peruser launchd tool configured, so that I can disable the daemons that are causing this error message?

  Read the article

• REST-based file server

  - by Chris Wenham

  I need to be able to PUT files and GET them later using nothing but HTTP, so I went searching for something that might match the terms "REST file server" or "HTTP file server" or "REST drop-box", etc. Unfortunately, these terms bring up the wrong kind of results on Google. What I want is the equivalent of an SMB fileshare over HTTP. Some ideal features: Can PUT a file of any type at http://servername/service/any/path/I/want/document.pdf Anyone with access can GET that file at the URL I PUT it at Supports AV scanning on any new file that has been PUT Supports DELETE of existing resources (files) Our shop runs Windows, but I'd be interested to know about Unix software that can do this kind of thing, too. It's to be used in an IT department for private users only. It won't be on a public-facing IP address. Does anything like this exist?

  Read the article

• What are these? Are they broken?

  - by Chris Nielsen

  Please excuse the poor image quality: What are the components that I've circled in red? The ones on the left look whole and solid. The ones on the right have cracked tops, and although this picture doesn't show it, there are small brown threads coming out of the top. Are the cracked ones broken, or is that supposed to happen? If they ARE broken, is this something I should worry about? This is a video card, and it appears to be fully functional: I'm using it while writing this post.

  Read the article

• WinXP: Changing default double-click from Open to Explore?

  - by chris

  Is it possible to configure XP so that a double-click on a folder opens up in Explorer view rather than the "regular" folder view?

  Read the article

• Samba doesnt require password on xbmc but does on ubuntu

  - by Chris

  I have samba setup on a fedora 13 machine, and I use it to share with my xbmc client in the family room. When I set this up there no password or anything was required I merely entered in paths such as: smb://<host>/<share> and all worked. Now on my ubuntu 10.04 machine when I try to access the same hosts, for example through smbmount though I receive an error. smbmount //media/Music ~/Music/ # media is in my /etc/hosts and resolves to # correct IP address for the machine I receive error: operation not permitted after pressing enter when it prompts for password. Here is my entry from /etc/samba/smb.conf: [global] workgroup = WORKGROUP server string = Samba Server Version %v # log files split per-machine: log file = /var/log/samba/log.%m # maximum size of 50KB per log file, then rotate: max log size = 50 security = user passdb backend = tdbsam ; security = domain ; passdb backend = tdbsam ; realm = MY_REALM ; password server = <NT-Server-Name> ; security = user ; passdb backend = tdbsam ; domain master = yes ; domain logons = yes ; logon script = %m.bat ; logon script = %u.bat ; logon path = \\%L\Profiles\%u ; logon path = ; add user script = /usr/sbin/useradd "%u" -n -g users ; add group script = /usr/sbin/groupadd "%g" ; add machine script = /usr/sbin/useradd -n -c "Workstation (%u)" -M -d /nohome -s /bin/false "%u" ; delete user script = /usr/sbin/userdel "%u" ; delete user from group script = /usr/sbin/userdel "%u" "%g" ; delete group script = /usr/sbin/groupdel "%g" ; local master = no ; os level = 33 ; preferred master = yes ; wins support = yes ; wins server = w.x.y.z ; wins proxy = yes ; dns proxy = yes load printers = yes cups options = raw ; printcap name = /etc/printcap # obtain a list of printers automatically on UNIX System V systems: ; printcap name = lpstat ; printing = cups ; map archive = no ; map hidden = no ; map read only = no ; map system = no ; store dos attributes = yes #============================ Share Definitions ============================== [homes] comment = Home Directories browseable = no writable = yes ; valid users = %S ; valid users = MYDOMAIN\%S # Un-comment the following and create the netlogon directory for Domain Logons: ; [netlogon] ; comment = Network Logon Service ; path = /var/lib/samba/netlogon ; guest ok = yes ; writable = no ; share modes = no # Un-comment the following to provide a specific roving profile share. # The default is to use the user's home directory: ; [Profiles] ; path = /var/lib/samba/profiles ; browseable = no ; guest ok = yes # A publicly accessible directory that is read only, except for users in the # "staff" group (which have write permissions): ; [public] ; comment = Public Stuff ; path = /home/samba ; public = yes ; writable = yes ; printable = no ; write list = +staff [tv] comment = TV path = /media/Isos/tv public = yes writable = yes printable = no write list = +media [music] comment = Music path = /media/Storage/music/ public = yes writable = yes printable = no write list = +media [pictures] comment = Pictures path = /media/Storage/pictures public = yes writable = yes printable = no write list = +media

  Read the article

• Laptops trying to connect via wireless? Only able to connect only via wired connection

  - by Chris J. Lee

  It seems that all the wireless laptops in the office have disconnected and are unable to reconnect to the wifi after a terrible storm caused some power interruptions. Troubleshooting actions Verify wireless broadcasting is up With each laptop i ended up flushing their dns cache on Win 7 (ipconfig /flush ) Performed an ipconfig /all to see what the new ip is Made sure password was correct Reset the router (multiple times) restarted each laptop. Tried connecting wirelessly Am i missing some small detail ? Network information The router is a linksys/cisco WRVS4400N router. Supports a lot of fancy features i don't know how to use. We have 3 static ip's the conference room computer, the wireless printer, my computer Mostly windows machines, we have 3 mac users

  Read the article

• fsck: FILE SYSTEM WAS MODIFIED after each check with -c, why?

  - by Chris

  I use a script to partition and format CF cards (connected with a USB card writer) in an automated way. After the main process I check the card again with fsck. To check bad blocks I also tried the '-c' switch, but I always get a return value != 0 and the message "FILE SYSTEM WAS MODIFIED" (see below). I get the same result when checking the very same drive several times... Does anyone know why a) the file system is modified at all and b) why this seems to happen every time I check and not only in case of an error (like bad blocks)? Here's the output: linux-box# fsck.ext3 -c /dev/sdx1 e2fsck 1.40.2 (12-Jul-2007) Checking for bad blocks (read-only test): done Pass 1: Checking inodes, blocks, and sizes Pass 2: Checking directory structure Pass 3: Checking directory connectivity Pass 4: Checking reference counts Pass 5: Checking group summary information Volume (/dev/sdx1): ***** FILE SYSTEM WAS MODIFIED ***** Volume (/dev/sdx1): 5132/245760 files (1.2% non-contiguous), 178910/1959896 blocks

  Read the article

• Puppet: Could not find init script for 'squid'

  - by chris

  I'm using Puppet to install ufdbGuard which requires Squid 2.7 (which is correctly installed and working properly). Here is the relevant class: class pns_client::squid { package { 'squid': ensure => present, before => File['/etc/squid/squid.conf'], } if $::ufdbguard_installed == "true" { $squidconf = 'puppet:///modules/pns_client/squid.conf_ufdbguard' } else { $squidconf = 'puppet:///modules/pns_client/squid.conf' } notify{$squidconf:} file { '/etc/squid/squid.conf': ensure => file, mode => 644, source => $squidconf, } service { 'squid': ensure => running, enable => true, hasrestart => true, hasstatus => true, subscribe => File['/etc/squid/squid.conf'], } } When running, I get this error: err: /Stage[main]/Pns_client::Squid/Service[squid]: Could not evaluate: Could not find init script for 'squid' This happens on all freshly-installed Debian 6 and Unbuntu 10.04/11.04 machines. Any ideas?

  Read the article

< Previous Page | 54 55 56 57 58 59 60 61 62 63 64 65  | Next Page >