Search Results

Search found 11364 results on 455 pages for 'port blocking'.

Page 58/455 | < Previous Page | 54 55 56 57 58 59 60 61 62 63 64 65  | Next Page >

  • L2TP iptables port forward

    - by The_cobra666
    Hi all, I'm setting up port forwarding for an L2TP VPN connection to the local Windows 2003 VPN server. The router is a simpel Debian machine with iptables. The VPN server works perfect. But I cannot log in from the WAN. I'm missing something. The VPN server is using a pre-shared key (L2TP) and give's out an IP in the range: 192.168.3.0. Local network range is 192.168.2.0/24 I added the route: with route add -net 192.168.3.0 netmask 255.255.255.240 gw 192.168.2.13 (the vpn server) iptables -t nat -A PREROUTING -p udp --dport 1701 -i eth0 -j DNAT --to 192.168.2.13 iptables -A FORWARD -p udp --dport 1701 -j ACCEPT iptables -t nat -A PREROUTING -p udp --dport 500 -i eth0 -j DNAT --to 192.168.2.13 iptables -A FORWARD -p udp --dport 500 -j ACCEPT iptables -t nat -A PREROUTING -p udp --dport 4500 -i eth0 -j DNAT --to 192.168.2.13 iptables -A FORWARD -p udp --dport 4500 -j ACCEPT iptables -t nat -A PREROUTING -p 50 -j DNAT --to 192.168.2.13 iptables -A FORWARD -p 50 -j ACCEPT iptables -t nat -A PREROUTING -p 51 -j DNAT --to 192.168.2.13 iptables -A FORWARD -p 51 -j ACCEPT The whole iptables script is (without the line's from above): echo 1 > /proc/sys/net/ipv4/ip_forward echo 1 > /proc/sys/net/ipv4/tcp_syncookies #Flush table's iptables -F INPUT iptables -F OUTPUT iptables -F FORWARD iptables -t nat -F #Drop traffic iptables -P INPUT DROP iptables -P FORWARD DROP iptables -P OUTPUT ACCEPT #verkeer naar buiten toe laten en nat aanzetten iptables -A FORWARD -i eth0 -o eth1 -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -i eth1 -o eth0 -j ACCEPT iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE #RDP forward voor windows servers iptables -t nat -A PREROUTING -p tcp --dport 3389 -i eth0 -j DNAT --to 192.168.2.10:3389 iptables -A FORWARD -p tcp --dport 3389 -j ACCEPT iptables -t nat -A PREROUTING -p tcp --dport 3340 -i eth0 -j DNAT --to 192.168.2.12:3340 iptables -A FORWARD -p tcp --dport 3340 -j ACCEPT #toestaan SSH verkeer iptables -t nat -A PREROUTING -p tcp --dport 22 -i eth0 -j DNAT --to-destination 192.168.2.1 iptables -A INPUT -p tcp --dport 22 -j ACCEPT #toestaan verkeer loopback iptables -A INPUT -i lo -j ACCEPT #toestaan lokaal netwerk iptables -A INPUT -i eth1 -j ACCEPT #accepteren established traffic iptables -A INPUT -i eth0 --match state --state RELATED,ESTABLISHED -j ACCEPT #droppen ICMP boodschappen iptables -A INPUT -p icmp -i eth0 -m limit --limit 10/minute -j ACCEPT iptables -A INPUT -p icmp -i eth0 -j REJECT ifconfig eth1 192.168.2.1/24 ifconfig eth0 XXXXXXXXXXXXX/30 ifconfig eth0 up ifconfig eth1 up route add default gw XXXXXXXXXXXXXXXXXXX route add -net 192.168.3.0 netmask 255.255.255.240 gw 192.168.2.13

    Read the article

  • Problem installing Cardbus/PCMCIA drivers (USB 2.0 2-port)

    - by Carl
    I obtained the drivers from the manufacturer for my HT-Link NEC USB 2.0 2-port Cardbus card. When I plugged in the card before I got the drivers, 3 new entries showed up in the Device Manager - two "NEC PCI to USB Open Host Controller" and one "Standard Enhanced PCI to USB Host controller." With the card plugged in, I uninstalled those two drivers. I then removed the card. I copied the new drivers to c:\windows\system32\drivers and the .inf file to c:\windows\inf. I also copied the drivers & inf to a new directory called c:\windows\drivers\ousb2. I reinserted the card. Windows automatically installed the same drivers as before. I selected 'update driver' on the "NEC PCI to USB..." entry and didn't see any other options. I then selected 'have disk' and pointed to c:\windows\drivers\ousb2 and got a message "The specified location does not contain information about your hardware." I then selected 'update driver' on the "Standard Enhanced PCI to USB...," and manually selected "USB 2.0 Enhanced Host Controller" (OWC 4/15/2003 2.1.3.1). Windows then automatically found a USB root hub, and I manually selected "USB 2.0 Root Hub Device" (OWC 4/15/2003 2.1.3.1). Now there are two sections in the Device Manager titled "Universal Serial Bus controllers." I plugged in my external USB hard disk adapter, and "USB Mass Storage Device" was added to the first set. Here's how it looks (w/drivers from the properties): [Universal Serial Bus controllers] Intel(R) 82801DB/DBM USB 2.0 Enhanced Host Controller - 24CD (6/1/2002 5.1.2600.0) Intel(R) 82801DB/DBM USB Universal Host Controller - 24C2 (7/1/2001 5.1.2600.5512) Intel(R) 82801DB/DBM USB Universal Host Controller - 24C4 (7/1/2001 5.1.2600.5512) Intel(R) 82801DB/DBM USB Universal Host Controller - 24C7 (7/1/2001 5.1.2600.5512) NEC PCI to USB Open Host Controller (7/1/2001 5.1.2600.5512) NEC PCI to USB Open Host Controller (7/1/2001 5.1.2600.5512) USB Mass Storage Device USB Root Hub (7/1/2001 5.1.2600.5512) (5 more USB Root Hubs - same driver) [Universal Serial Bus controllers] USB 2.0 Enhanced Host Controller (OWC 4/15/2003 2.1.3.1) USB 2.0 Root Hub Device (OWC 4/15/2003 2.1.3.1) When I unplug the card the two "NEC PCI to USB..." entries in the first set disappear, and the whole second set disappears. (I unplugged the hard disk adapter first...) The hard disk adapter still doesn't work in that Cardbus card with the new drivers. I don't think the above looks right - a second set of USB controllers listed in the Device Manager, and the NEC entries still in the first set, and the the USB mass storage device still in the first set. Any help appreciated. (Windows XP PRO SP3 w/all current updates.)

    Read the article

  • How can I troubleshoot Virtualbox port forwarding from Windows guest to OSX host not working?

    - by joe larson
    There are a plethora of questions about virtual box port forwarding problems but none with my specific details. I have a Windows install living in Virtual Box, hosted within OSX. I've got several webservers running on localhost on different ports within the Windows install. I cannot for the life of me get port forwarding to work so I can access those webservers from OSX. My settings look like this (yes I have a NAT adapter): And in my vbox configuration file the relavent portion looks like this: <NAT> <DNS pass-domain="true" use-proxy="false" use-host-resolver="false"/> <Alias logging="false" proxy-only="false" use-same-ports="false"/> <Forwarding name="RLPWeb" proto="1" hostport="7084" guestip="127.0.0.1" guestport="7084"/> <Forwarding name="UtilWeb" proto="1" hostport="4040" guestip="127.0.0.1" guestport="4040"/> <Forwarding name="WCARLP" proto="1" hostport="8084" guestip="127.0.0.1" guestport="8084"/> <Forwarding name="WCAUtil" proto="1" hostport="4848" guestip="127.0.0.1" guestport="4848"/> </NAT> I've turned off the Windows firewall to ensure it is not interfering, and I am not running a firewall on OSX. Anyway, when I attempt to go to for example http://127.0.0.1:4040/ on any of my OSX browsers, it will eventually time out. The log file for this VM shows that it is correctly reading the settings and implying it's doing the right thing here: 00:00:08.286 NAT: set redirect TCP host port 4848 => guest port 4848 @ 127.0.0.1 00:00:08.286 NAT: set redirect TCP host port 8084 => guest port 8084 @ 127.0.0.1 00:00:08.286 NAT: set redirect TCP host port 4040 => guest port 4040 @ 127.0.0.1 00:00:08.286 NAT: set redirect TCP host port 7084 => guest port 7084 @ 127.0.0.1 00:00:08.290 Changing the VM state from 'LOADING' to 'SUSPENDED'. 00:00:08.290 Changing the VM state from 'SUSPENDED' to 'RESUMING'. 00:00:08.290 Changing the VM state from 'RESUMING' to 'RUNNING'. 00:00:08.337 Display::handleDisplayResize(): uScreenId = 0, pvVRAM=000000012017d000 w=1834 h=929 bpp=32 cbLine=0x1CA8, flags=0x1 00:00:09.139 AIOMgr: Host limits number of active IO requests to 16. Expect a performance impact. 00:00:13.454 NAT: DHCP offered IP address 10.0.2.15 I've tried setting the Host IP to 127.0.0.1, and I've tried setting Guest IP blank and also 10.0.2.15. None of these seem to help. What else can I look at to troubleshoot this issue? Details of setup: OSX 10.6.8 Windows 7 Professional 64bit VirtualBox 4.1.2

    Read the article

  • How to start nginx via different port(other than 80)

    - by Zhao Peng
    Hi I am a newbie on nginx, I tried to set it up on my server(running Ubuntu 4), which already has apache running. So after I apt-get install it, I tried to start nginx. Then I get the message like this: Starting nginx: the configuration file /etc/nginx/nginx.conf syntax is ok configuration file /etc/nginx/nginx.conf test is successful [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) That makes sense as Apache is using port 80. Then I tried to modify nginx.conf, I reference some articles, so I changed it like so: server { listen 8080; location / { proxy_pass http://94.143.9.34:9500; proxy_set_header Host $host:8080; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Via "nginx"; } After saving this and try to start nginx again, I still get the same error as previously. I cannot really find a related post about this, could any good people shred some light? Thanks in advance :) ========================================================================= I should post all the content in conf here: user www-data; worker_processes 1; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 1024; # multi_accept on; } http { include /etc/nginx/mime.types; access_log /var/log/nginx/access.log; sendfile on; #tcp_nopush on; #keepalive_timeout 0; keepalive_timeout 65; tcp_nodelay on; gzip on; gzip_disable "MSIE [1-6]\.(?!.*SV1)"; include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; server { listen 81; location / { proxy_pass http://94.143.9.34:9500; proxy_set_header Host $host:81; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Via "nginx"; } } } mail { See sample authentication script at: http://wiki.nginx.org/NginxImapAuthenticateWithApachePhpScript auth_http localhost/auth.php; pop3_capabilities "TOP" "USER"; imap_capabilities "IMAP4rev1" "UIDPLUS"; server { listen localhost:110; protocol pop3; proxy on; } server { listen localhost:143; protocol imap; proxy on; } } Basically, I changed nothing except adding the server part.

    Read the article

  • How to forward OpenVPN Port to NAT'd XEN domU

    - by John
    I want to install a OpenVPN domU on XEN. Dom0 and domU are running Debian Squeeze, all domU are on a NAT'd privat network 10.0.0.1/24 My VPN-Gate is von 10.0.0.1 and running. How can I make it accessible under the dom0 public IP? I tried forwarding the port using iptables, but without any success. Here is what i did: ~ # iptables -L -n -v Chain INPUT (policy ACCEPT 1397 packets, 118K bytes) pkts bytes target prot opt in out source destination Chain FORWARD (policy ACCEPT 930 packets, 133K bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED PHYSDEV match --physdev-out vif5.0 0 0 ACCEPT udp -- * * 0.0.0.0/0 0.0.0.0/0 PHYSDEV match --physdev-in vif5.0 udp spt:68 dpt:67 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED PHYSDEV match --physdev-out vif5.0 0 0 ACCEPT all -- * * 10.0.0.1 0.0.0.0/0 PHYSDEV match --physdev-in vif5.0 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED PHYSDEV match --physdev-out vif3.0 0 0 ACCEPT udp -- * * 0.0.0.0/0 0.0.0.0/0 PHYSDEV match --physdev-in vif3.0 udp spt:68 dpt:67 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED PHYSDEV match --physdev-out vif3.0 0 0 ACCEPT all -- * * 10.0.0.5 0.0.0.0/0 PHYSDEV match --physdev-in vif3.0 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED PHYSDEV match --physdev-out vif2.0 0 0 ACCEPT udp -- * * 0.0.0.0/0 0.0.0.0/0 PHYSDEV match --physdev-in vif2.0 udp spt:68 dpt:67 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED PHYSDEV match --physdev-out vif2.0 0 0 ACCEPT all -- * * 10.0.0.2 0.0.0.0/0 PHYSDEV match --physdev-in vif2.0 147 8236 ACCEPT tcp -- eth0 * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:80 13 546 ACCEPT udp -- eth0 * 0.0.0.0/0 0.0.0.0/0 udp dpt:1194 Chain OUTPUT (policy ACCEPT 1000 packets, 99240 bytes) pkts bytes target prot opt in out source destination ~ # iptables -L -t nat -n -v Chain PREROUTING (policy ACCEPT 324 packets, 23925 bytes) pkts bytes target prot opt in out source destination 139 7824 DNAT tcp -- eth0 * 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 to:10.0.0.5:80 1 42 DNAT udp -- * * 0.0.0.0/0 0.0.0.0/0 udp dpt:1194 to:10.0.0.1:1194 Chain POSTROUTING (policy ACCEPT 92 packets, 5030 bytes) pkts bytes target prot opt in out source destination 863 64983 MASQUERADE all -- * eth0 0.0.0.0/0 0.0.0.0/0 0 0 MASQUERADE all -- * eth0 0.0.0.0/0 0.0.0.0/0 0 0 MASQUERADE all -- * eth0 0.0.0.0/0 0.0.0.0/0 Chain OUTPUT (policy ACCEPT 180 packets, 13953 bytes) pkts bytes target prot opt in out source destination

    Read the article

  • Problems configuring an SSH tunnel to a Nexentastor appliance for use with headless Crashplan

    - by Rob Smallshire
    Problem I am attempting to configure an SSH tunnel to a NexentaStor appliance from either a Windows or Linux computer so that I can connect a Crashplan Desktop GUI to a headless Crashplan server running on the Nexenta box, according to these instructions on the Crashplan support site: Connect to a Headless CrashPlan Desktop. So far, I've failed to get a working SSH tunnel from from either either a Windows client (using Putty) or a Linux client (using command line SSH). I'm fairly sure the problem is at the receiving end with NexentaStor. A blog article - CrashPlan for Backup on Nexenta - indicates that it could be made to work only after "after enabling TCP forwarding in Nexenta in /etc/ssh/sshd_config" - although I'm not sure how to go about that or specifically what I need to do. Things I have tried Ensuring the Crashplan server on the Nexenta box is listening on port 4243 $ netstat -na | grep LISTEN | grep 42 127.0.0.1.4243 *.* 0 0 131072 0 LISTEN *.4242 *.* 0 0 65928 0 LISTEN Establishing a tunnel from a Linux host: $ ssh -L 4200:localhost:4243 admin:10.0.0.56 and then, from another terminal on the Linux host, using telnet to verify the tunnel: $ telnet localhost 4200 Trying ::1... Connected to localhost. Escape character is #^]'. with nothing more, although the Crashplan server should respond with something. From Windows, using PuTTY have followed the instructions on the Crashplan support site to establish an equivalent tunnel, but then telnet on Windows gives me no response at all and the Crashplan GUI can't connect either. The PuTTY log for the tunnelled connection shows reasonable output: ... 2011-11-18 21:09:57 Opened channel for session 2011-11-18 21:09:57 Local port 4200 forwarding to localhost:4243 2011-11-18 21:09:57 Allocated pty (ospeed 38400bps, ispeed 38400bps) 2011-11-18 21:09:57 Started a shell/command 2011-11-18 21:10:09 Opening forwarded connection to localhost:4243 but the telnet localhost 4200 command from Windows does nothing at all - it just waits with a blank terminal. On the NexentaStor server I've examined the /etc/ssh/sshd_config file and everything seems 'normal' - and I've commented out the ListenAddress entries to ensure that I'm listening on all interfaces. How can I establish a tunnel, and how can I verify that it is working?

    Read the article

  • Changing externally visible IP on a multi-IP router?

    - by AlternateZ
    I work at a public library and I'm trying to configure OCLC's EzProxy software. I've run into a problem and I think it's related to our network config. I'm punching above my weight here a little so I need some help. I think I'm trying to configure a 1:1 NAT, but not sure how or if our hardware supports it. The EzProxy machine is on an internet line which supports multiple external IPs. Our router is a Billion BiGuard30. There's another server on this line, let's say its IP is x.x.x.9. The EzProxy machine is x.x.x.11 I've set up port forwarding from x.x.x.11 on the http ports to the EzProxy machine. Trying to browse to x.x.x.11 from an external PC works fine - we get to the EzProxy page we are serving. However, if we go to something like WhatIsMyIP from the EzProxy machine, it says that its IP is x.x.x.9. This causes problems with our user authentication software. How do we make the rest of the internet see that the machine is x.x.x.11? There doesnt seem to be any "outbound port forwarding" on the Billion router, nor is there any "1:1 NAT" options in its config webpage. The EzProxy machine is running Ubuntu 12.04, if that helps.

    Read the article

  • Forward differing hostnames to different internal IPs through NAT router

    - by abrereton
    Hi, I have one public IP address, one router and multiple servers behind the router. I would like to forward differing domains (All using HTTP) through the router to different servers. For example: example1.com => 192.168.0.110 example2.com => 192.168.0.120 foo.example2.com => 192.168.0.130 bar.example2.com => 192.168.0.140 I understand that this could be accomplished using Port Forwarding, but I need all hosts running on port 80. I found some information about IP Masquerading, but I found this difficult to understand, and I am not sure if it is what I am after. Another solution I have found is to direct all traffic to Reverse Proxy server, which forwards the requests onto the appropriate server. What about iptables? I am using a Billion 7404 VNPX router. Is there a feature that this router has that can accomplish this? Are these my only options? Have I missed something completely? Is one recommended over the others? I have searched around but I don't think I am hitting the correct keywords. Thanks in advance.

    Read the article

  • Make router forward HTTP and HTTPS traffic to external App

    - by cOsticla
    I use a Linksys WRT54GL router with DD-WRT v24-sp2 (10/10/09) std (SVN revision 13064) which I am trying to make forward all HTTP and HTTPS traffic to an external app called Fiddler (used as proxy) on port 8888. After a lot of digging on this site, dd-wrt forum, dd-wrt.com and WWW, I am stacked with the following piece of code that works (thanks to the guys from dd-wrt support for this info), but only for forwarding HTTP traffic (port 80): #!/bin/sh PROXY_IP=1234567890 PROXY_PORT=8888 LAN_IP=`nvram get lan_ipaddr` LAN_NET=$LAN_IP/`nvram get lan_netmask` iptables -t nat -A PREROUTING -i br0 -s $LAN_NET -d $LAN_NET -p tcp --dport 80 -j ACCEPT iptables -t nat -A PREROUTING -i br0 -s ! $PROXY_IP -p tcp --dport 80 -j DNAT --to $PROXY_IP:$PROXY_PORT iptables -t nat -I POSTROUTING -o br0 -s $LAN_NET -d $PROXY_IP -p tcp -j SNAT --to $LAN_IP iptables -I FORWARD -i br0 -o br0 -s $LAN_NET -d $PROXY_IP -p tcp --dport $PROXY_PORT -j ACCEPT I tried to edit the code from above and I came up with the following but it's still not forwarding HTTPS but just HTTP traffic: #!/bin/sh PROXY_IP=1234567890 PROXY_PORT=8888 LAN_IP=`nvram get lan_ipaddr` LAN_NET=$LAN_IP/`nvram get lan_netmask` iptables -t nat -A PREROUTING -i br0 -s $LAN_NET -d $LAN_NET -p tcp -m multiport --dports 80,443 -j ACCEPT iptables -t nat -A PREROUTING -i br0 -s ! $PROXY_IP -p tcp -m multiport --dports 80,443 -j DNAT --to $PROXY_IP:$PROXY_PORT iptables -t nat -I POSTROUTING -o br0 -s $LAN_NET -d $PROXY_IP -p tcp -j SNAT --to $LAN_IP iptables -I FORWARD -i br0 -o br0 -s $LAN_NET -d $PROXY_IP -p tcp --dport $PROXY_PORT -j ACCEPT I am not sure if is possible to forward HTTPS traffic anymore by just using a router so I'd appreciate if somebody will share his thoughts and/or examples regarding this subject here. Thanks!

    Read the article

  • IPtables: DNAT not working

    - by GetFree
    In a CentOS server I have, I want to forward port 8080 to a third-party webserver. So I added this rule: iptables -t nat -A PREROUTING -p tcp --dport 8080 -j DNAT --to-destination thirdparty_server_ip:80 But it doesn't seem to work. In an effort to debug the process, I added these two LOG rules: iptables -t mangle -A PREROUTING -p tcp --src my_laptop_ip --dport ! 22 -j LOG --log-level warning --log-prefix "[_REQUEST_COMING_FROM_CLIENT_] " iptables -t nat -A POSTROUTING -p tcp --dst thirdparty_server_ip -j LOG --log-level warning --log-prefix "[_REQUEST_BEING_FORWARDED_] " (the --dport ! 22 part is there just to filter out the SSH traffic so that my log file doesn't get flooded) According to this page the mangle/PREROUTING chain is the first one to process incomming packets and the nat/POSTROUTING chain is the last one to process outgoing packets. And since the nat/PREROUTING chain comes in the middle of the other two, the three rules should do this: the rule in mangle/PREROUTING logs the incomming packets the rule in nat/PREROUTING modifies the packets (it changes the dest IP and port) the rule in nat/POSTROUTING logs the modified packets about to be forwarded Although the first rule does log incomming packets comming from my laptop, the third rule doesn't log the packets which are supposed to be modified by the second rule. It does log, however, packets that are produced in the server, hence I know the two LOG rules are working properly. Why are the packets not being forwarded, or at least why are they not being logged by the third rule? PS: there are no more rules than those three. All other chains in all tables are empty and with policy ACCEPT.

    Read the article

  • Piecing together low-powered hardware for an RS-232 terminal server

    - by Fred
    I'm working on reconstructing my Cisco lab for training/educational purposes and I found that the actual terminal server I have is dead. I have a couple of 8-port PCI serial cards which would be more than ample for my lab, but I don't want to leave my personal computer running to be able to access the console ports. Ideally I would access the terminal server remotely, either by SSH/RDP to the box (depending on what OS I go with) or by installing a software package that allows me to telnet directly to a serial port. I know I've found a program that does this under Linux in the past but its name escapes me at the moment. I'm thinking about scavenging for some old hardware, on eBay or something, to put together a low-powered PC. Needs to be something that: Has Low-power consumption Has at least 2 PCI slots (though I certainly wouldn't complain about having more) Has onboard Ethernet (or, if not, another PCI or ISA slot (not shared)) Can be headless once an OS installed (probably Linux) I'm currently leaning towards an old fashioned Pentium (sub-133MHz era) but I am wondering if anybody else knows of another platform/mobo that would suit these needs. Alternatively, I've been considering buying a Raspberry Pi and a big USB hub along with a bunch of USB-Serial adapters but this sounds like it'd get messy quick with cables and adapters all over the place, and I may not even have the same ttyS#'s between boots.

    Read the article

  • Mac Mavericks, ngircd localhost works, private IP doesn't

    - by user221945
    I have configured ngircd to listen on my private ip address. It doesn't. Localhost works fine. Configuration test: ngIRCd 21-IDENT+IPv6+IRCPLUS+SSL+SYSLOG+TCPWRAP+ZLIB-x86_64/apple/darwin13.2.0 Copyright (c)2001-2013 Alexander Barton () and Contributors. Homepage: http://ngircd.barton.de/ This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. Reading configuration from "/opt/local/etc/ngircd.conf" ... OK, press enter to see a dump of your server configuration ... [GLOBAL] Name = irc.bellbookandpistol.com AdminInfo1 = Jaedreth AdminInfo2 = San Diego County CA, US AdminEMail = [email protected] HelpFile = /opt/local/share/doc/ngircd/Commands.txt Info = Server Info Text Listen = 10.0.1.5,127.0.0.1 MotdFile = MotdPhrase = "Welcome to irc.bellbookandpistol.com" Password = PidFile = Ports = 6667 ServerGID = wheel ServerUID = root [LIMITS] ConnectRetry = 60 IdleTimeout = 0 MaxConnections = 0 MaxConnectionsIP = 6 MaxJoins = -1 MaxNickLength = 9 MaxListSize = 0 PingTimeout = 120 PongTimeout = 20 [OPTIONS] AllowedChannelTypes = #&+ AllowRemoteOper = no ChrootDir = CloakHost = CloakHostModeX = CloakHostSalt = kBih5mu\kVI!DC6eifT(hd4m/0'zb/=: CloakUserToNick = no ConnectIPv4 = yes ConnectIPv6 = no DefaultUserModes = DNS = yes IncludeDir = /opt/local/etc/ngircd.conf.d MorePrivacy = no NoticeAuth = no OperCanUseMode = no OperChanPAutoOp = yes OperServerMode = no RequireAuthPing = no ScrubCTCP = no SyslogFacility = local5 WebircPassword = [SSL] CertFile = CipherList = HIGH:!aNULL:@STRENGTH DHFile = KeyFile = KeyFilePassword = Ports = [OPERATOR] Name = [REDACTED] Password = [REDACTED] Mask = [CHANNEL] Name = #BBP Modes = tnk Key = MaxUsers = 0 Topic = Welcome to the Bell, Book and Pistol IRC Server! KeyFile = As you can see, it should be listening on 10.0.1.5, but it isn't. After turning on Apache manually, port 80 works on 10.0.1.5, but port 6667 doesn't. It only works on localhost. Is there some terminal command I could use or some config file I could edit to get this to work?

    Read the article

  • Find whether TV supports S Video

    - by Vik
    Hello Freinds I have a TV (some unknown model) which has 3 sockets to insert 3 wires red, yellow and white. A DVD Player can be connected to the TV using sockets and the TV displays that the TV is in AV mode when DVD is running. Now i have a Desktop which has a S Video Port and i have a wire to connect the S Video port from my computer to those red, yellow and white sockets using appropriate pins. Now i have searched all over the remote and it does not switches to S Video Mode, it has only 2 modes of operation i.e. 1 Cable Connection (Third Party DTH Receiver receives channels and i pay subscription) and 2 AV Mode. It does not have S Video Mode or any other mode. Now my question is whether i can connect the S Video cable from my desktop to the above described TV or i should look for a new TV if i wish to connect the S Video from Computer to TV or there is any sort of converter that can help? I did tried connecting the S Video cable from Desktop to TV, but it did'nt worked. TV kept on displaying Blue Screen of AV Mode. Regards

    Read the article

  • How can I use my cell phone to establish a dial-up networking connection?

    - by gWiz
    I am using Windows 7 and have a BlackBerry with T-Mobile (U.S.). I have paired the phone with my computer over Bluetooth, which automatically creates a serial port for it. I am able to open the port in PuTTY and successfully issue AT commands to the modem, including dialing. However, while using Windows to create and establish a Dial-Up Networking connection, I get an error dialog stating "Error 678. The remote computer did not respond." In my testing, I also tried setting up a connection to dial a number connected to a phone. When attempting to connect over this connection, the phone does ring but the very moment I answer the call, my computer displays the above error dialog. What must be done to successfully establish such a PPP connection? Some special AT initialization string perhaps? To clarify, I'm not referring to the well-described and popular technique known as "tethering," in which the remote host of the data link is the mobile service provider. I am interested specifically in establishing direct data links with remote hosts other than my mobile service provider. Think old-school landline connection to your friend's computer or BBS. Edit 1 As grawity pointed out in comments, the missing piece of the puzzle is the actual modulator that is compatible with v-series protocols, which I expected to be built into the cellphone. So far the best only software alternative I could find is this experimental project. Edit 2 Found this forum discussion today. The participants state that there is no old-school modem in the BlackBerry. Edit 3 When I place a call in PuTTY with ATD, immediately after the call is answered (and the callee is initiating the handshake) the cellphone returns OK. This is not the expected behavior for establishing a data connection. The phone should reciprocate the handshake, and upon success return CONNECT. (Alternatively it should return BUSY or NO CARRIER, but never simply OK.) Windows DUN must be interpreting this as the "Error 678" I was seeing.

    Read the article

  • Network structure --> Server 2k8r2 <--> Livebox <--> Router <--> Other PCs

    - by Yusuf
    I have a Livebox connection to the Internet and I have set up my network as follows: - Livebox <--> Win2k8R2 Server - Livebox <--> Netgear N150 Router - Router <--> Other PCs Therefore, in my LAN, - the Livebox has IP address 192.168.1.1, - the Router 192.168.1.12 (when accessed from the Livebox or the server), - the Router 10.0.0.1 (when accessed from the PCs connected to the Router), - the server 192.168.1.2, - the PCs 10.0.0.x I was using a previous configuration, which was as follows: - Livebox <--> Netgear N150 Router - Router <--> Win2k8R2 Server - Router <--> Other PCs Everything was simple, and I just had to forward all ports for incoming connection on the Livebox to the Router, and then forward the specific ports to the Server as needed (it must be however noted that any server I use is found on the Win2k8R2 server itself). In this previous configuration, the IP addresses were as follows: - Livebox 192.168.1.1 - Router 192.168.1.12 (when seen from Livebox) - Router 10.0.0.1 (when seen from server & PCs connected to it) - Server 10.0.0.2 - PCs 10.0.0.x So now of course, my port-forwarding does not work anymore since the server is not connected (directly) to the Router. What I would like to know is how do I configure the Livebox and Router to still have the features like before? From what I understand of networks (which is very limited, btw), I see these options: Make the router assign IPs like 192.168.1.x (but then I want the forwarding to be done from the router itself, is it possible?) The forwarding on the router to the server uses IP address 10.0.0.2. I could change it to 192.168.1.2 (Is that even possible, does it work?) Forward all ports from the Livebox itself to the server, and then manage them there (Is software-based port-forwarding as secure as hardware-based?)

    Read the article

  • Better urls for this internal web server?

    - by sprugman
    I've got a server that I have admin access to, but don't fully manage. (I think it's a virtual machine, but I'm not 100% sure. It's running Apache on Windows Server 2003.) I share the ip with another user, so my sites all have to use the :8080 port. This is kind of ugly. Also, AFAIK, the only access I have is through an ip address. (I'm inside a corporate firewall and don't think I have access to a DNS server or anything.) I've adjusted my hosts file so I don't have to use the ip address on my local machine, but that's not a very generic solution. Are there any options to 1) get rid of the port requirement 2) be able to use a name (maybe a machine name) instead of the ip address in a generic way? (I'm not really a network admin -- I'm a developer managing this machine. The IT folks who really manage it are a few people away from me and tough to get to do anything, so I'm looking for a light-weight solution if possible.)

    Read the article

  • Finding JNP port in JBoss from Servlet

    - by Steve Jackson
    I have a servlet running in JBoss (4.2.2.GA and 4.3-eap) that needs to connect to an EJB to do work. In general this code works fine to get the Context to connect and make RMI calls (all in the same server). public class ContextFactory { public static final int DEFAULT_JNDI_PORT = 1099; public static final String DEFAULT_CONTEXT_FACTORY_CLASS = "org.jnp.interfaces.NamingContextFactory"; public static final String DEFAULT_URL_PREFIXES = "org.jboss.naming:org.jnp.interfaces"; public Context createContext(String serverAddress) { //combine provider name and port String providerUrl = serverAddress + ":" + DEFAULT_JNDI_PORT; //Set properties needed for Context: factory, provider, and package prefixes. Hashtable<String, String> env = new Hashtable<String, String>(3); env.put(Context.INITIAL_CONTEXT_FACTORY, DEFAULT_CONTEXT_FACTORY_CLASS); env.put(Context.PROVIDER_URL, providerUrl); env.put(Context.URL_PKG_PREFIXES, DEFAULT_URL_PREFIXES); return new InitialContext(env); } Now, when I change the JNDI bind port from 1099 in server/conf/jboss-service.xml I can't figure out how to programatically find the correct port for the providerUrl above. I've dumped System.getProperties() and System.getEnv() and it doesn't appear there. I'm pretty sure I can set it in server/conf/jndi.properties as well, but I was hoping to avoid another magic config file. I've tried the HttpNamingContextFactory but that fails "java.net.ProtocolException: Server redirected too many times (20)" env.put(Context.INITIAL_CONTEXT_FACTORY, "org.jboss.naming.HttpNamingContextFactory"); env.put(Context.PROVIDER_URL, "http://" + serverAddress + ":8080/invoker/JNDIFactory"); Any ideas?

    Read the article

  • Find Port Number and Domain Name to connect to Hive Table

    - by user1419563
    I am new to Hive, MapReduce and Hadoop. I am using Putty to connect to hive table and access records in the tables. So what I did is- I opened Putty and in the host name I typed- ares-ingest.vip.host.com and then I click Open. And then I entered my username and password and then few commands to get to Hive sql. Below is the list what I did $ bash bash-3.00$ hive Hive history file=/tmp/rjamal/hive_job_log_rjamal_201207010451_1212680168.txt hive> set mapred.job.queue.name=hdmi-technology; hive> select * from table LIMIT 1; So my question is- I was trying to connect to Hive Tables using Squirrel SQL Client, so in that my Connection URL is- jdbc:hive://ares-ingest.vip.host.com:10000/default. So whenever I try to connect with these attributes, I always get Hive: Could not establish connection to ares-ingest.vip.host.com:10000/default: java.net.ConnectException: Connection timed out: connect. It might be possible I am using wrong port number or domain name here. Is there any way from the command prompt I can find out these two things, like what Domain Name and Port Number(where Hive server is running) should I use to connect to Hive table from Squirrel SQL Client. As I know host and port are determined by where the hive server is running

    Read the article

  • Reading binary data from serial port using Dejan TComport Delphi component

    - by johnma
    Apologies for this question but I am a bit of a noob with Delphi. I am using Dejan TComport component to get data from a serial port. A box of equipment connected to the port sends about 100 bytes of binary data to the serial port. What I want to do is extract the bytes as numerical values into an array so that I can perform calculations on them. TComport has a method Read(buffer,Count) which reads DATA from input buffer. function Read(var Buffer; Count: Integer): Integer; The help says the Buffer variable must be large enough to hold Count bytes but does not provide any example of how to use this function. I can see that the Count variable holds the number of bytes received but I can't find a way to access the bytes in Buffer. TComport also has a methord Readstr which reads data from input buffer into a STRING variable. function ReadStr(var Str: String; Count: Integer): Integer; Again the Count variable shows the number of bytes received and I can use Memo1.Text:=str to display some information but obviously Memo1 has problems displaying the control characters. I have tried various ways to try and extract the byte data from Str but so far without success. I am sure it must be easy. Here's hoping.

    Read the article

  • Javascript permission denied - different port

    - by Grnbeagle
    Hi, I have a rails app running on port 3000. The page in question has an iframe and I need to resize it depending on the height of the content loaded in the iframe. <iframe id="ifrm_col3" name="ifrm_col3" frameborder="0" src="<%=invite_path(@invite.alias)%>" onload="util.resize_iframe('ifrm_col3');"></iframe> The resize function is here: util.resize_iframe = function(frame_id) { var h = document.getElementById(frame_id).contentWindow.document.body.scrollHeight; document.getElementById(frame_id).height = h; } After the iframe loads, I see this error in FireBug: Error: Permission denied for <http://192.168.0.157> to get property Window.document from <http://192.168.0.157:3000>. Source File: http://192.168.0.157:3000/javascripts/application.js?1268327481 Line: 84 The src of iframe is a relative path, but I'm not sure why the port info from the parent page is not retained. Is there any workaround to this problem? I tried creating a function in the parent page and calling it from the iframe, but ran into the same issue. Due to extra features in the site, I need to stick to port 3000 for the rails app. Any suggestion is appreciated.

    Read the article

  • Excessive denied requests for port 58322 in syslog

    - by Nathan C.
    My iptables is setup to block all unneeded ports as it should but I'm checking my syslog due to these random but all-to-frequent apache2 crashes and I noticed a lot of requests such as this. In all the archived syslogs that I have these are present from different IP addresses. There is a similar question with an accepted here: What service uses UDP port 60059? Jun 4 06:49:27 HOSTNAME kernel: iptables denied: IN=eth0 OUT= MAC=fe:fd:ad:ff:dd:95:c8:4c:75:f5:d6:3f:08:00 SRC=218.7.74.50 DST=MY.SERVER.IP.HERE LEN=129 TOS=0x00 PREC=0x00 TTL=115 ID=27636 PROTO=UDP SPT=9520 DPT=58322 LEN=109 Jun 4 06:49:31 HOSTNAME kernel: iptables denied: IN=eth0 OUT= MAC=fe:fd:ad:ff:dd:95:c8:4c:75:f5:d6:3f:08:00 SRC=95.160.226.177 DST=MY.SERVER.IP.HERE LEN=131 TOS=0x00 PREC=0x00 TTL=116 ID=31468 PROTO=UDP SPT=47642 DPT=58322 LEN=111 Jun 4 06:49:54 HOSTNAME kernel: iptables denied: IN=eth0 OUT= MAC=fe:fd:ad:ff:dd:95:c8:4c:75:f5:d6:3f:08:00 SRC=78.137.36.10 DST=MY.SERVER.IP.HERE LEN=131 TOS=0x00 PREC=0x00 TTL=118 ID=21872 PROTO=UDP SPT=57872 DPT=58322 LEN=111 Jun 4 06:50:14 HOSTNAME kernel: iptables denied: IN=eth0 OUT= MAC=fe:fd:ad:ff:dd:95:c8:4c:75:f5:d6:3f:08:00 SRC=111.253.217.11 DST=MY.SERVER.IP.HERE LEN=131 TOS=0x00 PREC=0x00 TTL=116 ID=28882 PROTO=UDP SPT=51826 DPT=58322 LEN=111 Jun 4 06:51:02 HOSTNAME kernel: iptables denied: IN=eth0 OUT= MAC=fe:fd:ad:ff:dd:95:c8:4c:75:f5:d6:3f:08:00 SRC=189.45.114.173 DST=MY.SERVER.IP.HERE LEN=131 TOS=0x16 PREC=0x00 TTL=113 ID=19985 PROTO=UDP SPT=41087 DPT=58322 LEN=111 Jun 4 06:51:09 HOSTNAME kernel: iptables denied: IN=eth0 OUT= MAC=fe:fd:ad:ff:dd:95:c8:4c:75:f5:d6:3f:08:00 SRC=87.89.202.28 DST=MY.SERVER.IP.HERE LEN=131 TOS=0x00 PREC=0x00 TTL=116 ID=7874 PROTO=UDP SPT=17524 DPT=58322 LEN=111 Jun 4 06:51:20 HOSTNAME kernel: iptables denied: IN=eth0 OUT= MAC=fe:fd:ad:ff:dd:95:c8:4c:75:f5:d6:3f:08:00 SRC=24.44.124.35 DST=MY.SERVER.IP.HERE LEN=131 TOS=0x00 PREC=0x00 TTL=118 ID=12978 PROTO=UDP SPT=45596 DPT=58322 LEN=111 Jun 4 06:51:22 HOSTNAME kernel: iptables denied: IN=eth0 OUT= MAC=fe:fd:ad:ff:dd:95:c8:4c:75:f5:d6:3f:08:00 SRC=81.174.48.236 DST=MY.SERVER.IP.HERE LEN=93 TOS=0x00 PREC=0x00 TTL=48 ID=0 DF PROTO=UDP SPT=21352 DPT=58322 LEN=73 Jun 4 06:51:23 HOSTNAME kernel: iptables denied: IN=eth0 OUT= MAC=fe:fd:ad:ff:dd:95:c8:4c:75:f5:d6:3f:08:00 SRC=124.107.61.84 DST=MY.SERVER.IP.HERE LEN=131 TOS=0x00 PREC=0x00 TTL=114 ID=13038 PROTO=UDP SPT=14357 DPT=58322 LEN=111 Jun 4 06:51:30 HOSTNAME kernel: iptables denied: IN=eth0 OUT= MAC=fe:fd:ad:ff:dd:95:c8:4c:75:f5:d6:3f:08:00 SRC=88.8.23.200 DST=MY.SERVER.IP.HERE LEN=123 TOS=0x00 PREC=0x00 TTL=117 ID=21062 PROTO=UDP SPT=4291 DPT=58322 LEN=103 Jun 4 06:51:54 HOSTNAME kernel: iptables denied: IN=eth0 OUT= MAC=fe:fd:ad:ff:dd:95:c8:4c:75:f5:d6:3f:08:00 SRC=80.202.244.234 DST=MY.SERVER.IP.HERE LEN=129 TOS=0x00 PREC=0x00 TTL=114 ID=339 PROTO=UDP SPT=14020 DPT=58322 LEN=109 I'm not overly experienced with server configuration and debugging, so I only just installed logcheck after reading that previous question. I guess my question is what steps should I take after reading this log info to 1) further protect myself, 2) understand if this could be causing any other problems with my VPS, and 3) use this data to help others?

    Read the article

  • iptables 1.4 and passive FTP on custom port

    - by Cracky
    after the upgrade from debian squeeze to wheezy I've got a problem with passive FTP connection. I could narrow it to be iptables related, as I could connect via FTP w/o problems after adding my IP to the iptables ACCEPT rule. Before the upgrade I was able just to do modprobe nf_conntract_ftp ports=21332 and adding iptables -A THRU -p tcp --dport 21332 -m state --state NEW,ESTABLISHED,RELATED -j ACCEPT now..it doesn't help anymore. The INPUT rule is being triggered as I can see in the counter, but the directory listing is the last thing it does. Setting up a passive-port range is the last thing I want to do, I dislike open ports. I also tried the trick with helper mod by adding following rule before the actual rule for 21332 iptables -A THRU -p tcp -i eth0 --dport 21332 -m state --state NEW -m helper --helper ftp-21332 -j ACCEPT but it doesn't help and is even not being triggered according to counter. The rule in the next line (w/o helper) is being triggered.. here some info: # iptables --version iptables v1.4.14 # lsmod |grep nf_ nf_nat_ftp 12460 0 nf_nat 18242 1 nf_nat_ftp nf_conntrack_ftp 12605 1 nf_nat_ftp nf_conntrack_ipv4 14078 32 nf_nat nf_defrag_ipv4 12483 1 nf_conntrack_ipv4 nf_conntrack 52720 7 xt_state,nf_conntrack_ipv4,xt_conntrack,nf_conntrack_ftp,nf_nat,nf_nat_ftp,xt_helper # uname -a Linux loki 3.2.0-4-amd64 #1 SMP Debian 3.2.46-1 x86_64 GNU/Linux # iptables-save # Generated by iptables-save v1.4.14 on Sun Jun 30 03:54:28 2013 *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :BLACKLIST - [0:0] :LOGDROP - [0:0] :SPAM - [0:0] :THRU - [0:0] :WEB - [0:0] :fail2ban-dovecot-pop3imap - [0:0] :fail2ban-pureftpd - [0:0] :fail2ban-ssh - [0:0] -A INPUT -p tcp -m multiport --dports 110,995,143,993 -j fail2ban-dovecot-pop3imap -A INPUT -p tcp -m multiport --dports 21,21332 -j fail2ban-pureftpd -A INPUT -p tcp -m multiport --dports 22 -j fail2ban-ssh -A INPUT -p tcp -m multiport --dports 110,995,143,993 -j fail2ban-dovecot-pop3imap -A INPUT -i lo -j ACCEPT -A INPUT -i eth0 -p tcp -m tcp --tcp-flags FIN,SYN,RST,PSH,ACK,URG NONE -j DROP -A INPUT -i eth0 -p tcp -m tcp --tcp-flags FIN,SYN FIN,SYN -j DROP -A INPUT -i eth0 -p tcp -m tcp --tcp-flags SYN,RST SYN,RST -j DROP -A INPUT -i eth0 -p tcp -m tcp --tcp-flags FIN,RST FIN,RST -j DROP -A INPUT -i eth0 -p tcp -m tcp --tcp-flags FIN,ACK FIN -j DROP -A INPUT -i eth0 -p tcp -m tcp --tcp-flags ACK,URG URG -j DROP -A INPUT -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT -A INPUT -j BLACKLIST -A INPUT -j THRU -A INPUT -j LOGDROP -A OUTPUT -j ACCEPT -A OUTPUT -s 93.223.38.223/32 -j ACCEPT -A BLACKLIST -s 38.113.165.0/24 -j LOGDROP -A BLACKLIST -s 202.177.216.0/24 -j LOGDROP -A BLACKLIST -s 130.117.190.0/24 -j LOGDROP -A BLACKLIST -s 117.79.92.0/24 -j LOGDROP -A BLACKLIST -s 72.47.228.0/24 -j LOGDROP -A BLACKLIST -s 195.200.70.0/24 -j LOGDROP -A BLACKLIST -s 195.200.71.0/24 -j LOGDROP -A LOGDROP -m limit --limit 5/sec -j LOG --log-prefix drop_packet_ --log-level 7 -A LOGDROP -p tcp -m tcp --dport 25 -m limit --limit 2/sec -j LOG --log-prefix spam_blacklist --log-level 7 -A LOGDROP -p tcp -m tcp --dport 80 -m limit --limit 2/sec -j LOG --log-prefix web_blacklist --log-level 7 -A LOGDROP -p tcp -m tcp --dport 22 -m limit --limit 2/sec -j LOG --log-prefix ssh_blacklist --log-level 7 -A LOGDROP -j REJECT --reject-with icmp-host-prohibited -A THRU -p icmp -m limit --limit 1/sec -m icmp --icmp-type 8 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 25 -j ACCEPT -A THRU -i eth0 -p udp -m udp --dport 53 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 80 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 110 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 143 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 465 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 585 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 993 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 995 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 2008 -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 10011 -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 21332 -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 30033 -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT -A fail2ban-dovecot-pop3imap -j RETURN -A fail2ban-dovecot-pop3imap -j RETURN -A fail2ban-pureftpd -j RETURN -A fail2ban-pureftpd -j RETURN -A fail2ban-ssh -j RETURN -A fail2ban-ssh -j RETURN COMMIT # Completed on Sun Jun 30 03:54:28 2013 So, as I said, I have no problems with connecting when adding my IP to go through..but that's not a solution as noone except me can connect anymore~ If someone got an idea what the problem is, please help me! Thanks Cracky

    Read the article

  • Linux termios VTIME not working?

    - by San Jacinto
    We've been bashing our heads off of this one all morning. We've got some serial lines setup between an embedded linux device and an Ubuntu box. Our reads are getting screwed up because our code usually returns two (sometimes more, sometimes exactly one) message reads instead of one message read per actual message sent. Here is the code that opens the serial port. InterCharTime is set to 4. void COMBaseClass::OpenPort() { cerr<< "openning port"<< port <<"\n"; struct termios newtio; this->fd = -1; int fdTemp; fdTemp = open( port, O_RDWR | O_NOCTTY); if (fdTemp < 0) { portOpen = 0; cerr<<"problem openning "<< port <<". Retrying"<<endl; usleep(1000000); return; } newtio.c_cflag = BaudRate | CS8 | CLOCAL | CREAD ;//| StopBits; newtio.c_iflag = IGNPAR; newtio.c_oflag = 0; /* set input mode (non-canonical, no echo,...) */ newtio.c_lflag = 0; newtio.c_cc[VTIME] = InterCharTime; /* inter-character timer in .1 secs */ newtio.c_cc[VMIN] = readBufferSize; /* blocking read until 1 char received */ tcflush(fdTemp, TCIFLUSH); tcsetattr(fdTemp,TCSANOW,&newtio); this->fd = fdTemp; portOpen = 1; } The other end is configured similarly for communication, and has one small section of particular iterest: while (1) { sprintf(out, "\r\nHello world %lu", ++ulCount); puts(out); WritePort((BYTE *)out, strlen(out)+1); sleep(2); } //while Now, when I run a read thread on the receiving machine, "hello world" is usually broken up over a couple messages. Here is some sample output: 1: Hello 2: world 1 3: Hello 4: world 2 5: Hello 6: world 3 where number followed by a colon is one message recieved. Can you see any error we are making? Thank you. Edit: For clarity, please view section 3.2 of this resource href="http://www.faqs.org/docs/Linux-HOWTO/Serial-Programming-HOWTO.html. To my understanding, with a VTIME of a couple seconds (meaning vtime is set anywhere between 10 and 50, trial-and-error), and a VMIN of 1, there should be no reason that the message is broken up over two separate messages.

    Read the article

  • RHEL - blocked FC remote port time out: saving binding

    - by Dev G
    My Server went into a faulty state since the database could not write on the partition. I found out that the partition went into Read Only mode. Finally to fix it, I had to do a hard reboot. Linux 2.6.18-164.el5PAE #1 SMP Tue Aug 18 15:59:11 EDT 2009 i686 i686 i386 GNU/Linux /var/log/messages Oct 31 00:56:45 ota3g1 Had[17275]: VCS ERROR V-16-1-10214 Concurrency Violation:CurrentCount increased above 1 for failover group sg_network Oct 31 00:57:05 ota3g1 Had[17275]: VCS CRITICAL V-16-1-50086 CPU usage on ota3g1.mtsallstream.com is 100% Oct 31 01:01:47 ota3g1 Had[17275]: VCS ERROR V-16-1-10214 Concurrency Violation:CurrentCount increased above 1 for failover group sg_network Oct 31 01:06:50 ota3g1 Had[17275]: VCS ERROR V-16-1-10214 Concurrency Violation:CurrentCount increased above 1 for failover group sg_network Oct 31 01:11:52 ota3g1 Had[17275]: VCS ERROR V-16-1-10214 Concurrency Violation:CurrentCount increased above 1 for failover group sg_network Oct 31 01:12:10 ota3g1 kernel: lpfc 0000:29:00.1: 1:1305 Link Down Event x2 received Data: x2 x20 x80000 x0 x0 Oct 31 01:12:10 ota3g1 kernel: lpfc 0000:29:00.1: 1:1303 Link Up Event x3 received Data: x3 x1 x10 x1 x0 x0 0 Oct 31 01:12:12 ota3g1 kernel: lpfc 0000:29:00.1: 1:1305 Link Down Event x4 received Data: x4 x20 x80000 x0 x0 Oct 31 01:12:40 ota3g1 kernel: rport-8:0-0: blocked FC remote port time out: saving binding Oct 31 01:12:40 ota3g1 kernel: lpfc 0000:29:00.1: 1:(0):0203 Devloss timeout on WWPN 20:25:00:a0:b8:74:f5:65 NPort x0000e4 Data: x0 x7 x0 Oct 31 01:12:40 ota3g1 kernel: sd 8:0:0:4: SCSI error: return code = 0x00010000 Oct 31 01:12:40 ota3g1 kernel: end_request: I/O error, dev sdi, sector 38617577 Oct 31 01:12:40 ota3g1 kernel: sd 8:0:0:4: SCSI error: return code = 0x00010000 Oct 31 01:12:40 ota3g1 kernel: end_request: I/O error, dev sdi, sector 283532153 Oct 31 01:12:40 ota3g1 kernel: sd 8:0:0:4: SCSI error: return code = 0x00010000 Oct 31 01:12:40 ota3g1 kernel: end_request: I/O error, dev sdi, sector 90825 Oct 31 01:12:40 ota3g1 kernel: Aborting journal on device dm-16. Oct 31 01:12:40 ota3g1 kernel: sd 8:0:0:4: SCSI error: return code = 0x00010000 Oct 31 01:12:40 ota3g1 kernel: end_request: I/O error, dev sdi, sector 868841 Oct 31 01:12:40 ota3g1 kernel: sd 8:0:0:4: SCSI error: return code = 0x00010000 Oct 31 01:12:40 ota3g1 kernel: Aborting journal on device dm-10. Oct 31 01:12:40 ota3g1 kernel: end_request: I/O error, dev sdi, sector 37759889 Oct 31 01:12:40 ota3g1 kernel: sd 8:0:0:4: SCSI error: return code = 0x00010000 Oct 31 01:12:40 ota3g1 kernel: end_request: I/O error, dev sdi, sector 283349449 Oct 31 01:12:40 ota3g1 kernel: printk: 6 messages suppressed. Oct 31 01:12:40 ota3g1 kernel: Aborting journal on device dm-12. Oct 31 01:12:40 ota3g1 kernel: EXT3-fs error (device dm-12) in ext3_reserve_inode_write: Journal has aborted Oct 31 01:12:40 ota3g1 kernel: Buffer I/O error on device dm-16, logical block 1545 Oct 31 01:12:40 ota3g1 kernel: lost page write due to I/O error on dm-16 Oct 31 01:12:40 ota3g1 kernel: sd 8:0:0:4: SCSI error: return code = 0x00010000 Oct 31 01:12:40 ota3g1 kernel: end_request: I/O error, dev sdi, sector 12745 Oct 31 01:12:40 ota3g1 kernel: Buffer I/O error on device dm-10, logical block 1545 Oct 31 01:12:40 ota3g1 kernel: EXT3-fs error (device dm-16) in ext3_reserve_inode_write: Journal has aborted Oct 31 01:12:40 ota3g1 kernel: lost page write due to I/O error on dm-10 Oct 31 01:12:40 ota3g1 kernel: sd 8:0:0:4: SCSI error: return code = 0x00010000 Oct 31 01:12:40 ota3g1 kernel: end_request: I/O error, dev sdi, sector 37749121 Oct 31 01:12:40 ota3g1 kernel: Buffer I/O error on device dm-12, logical block 0 Oct 31 01:12:40 ota3g1 kernel: lost page write due to I/O error on dm-12 Oct 31 01:12:40 ota3g1 kernel: sd 8:0:0:4: SCSI error: return code = 0x00010000 Oct 31 01:12:40 ota3g1 kernel: EXT3-fs error (device dm-12) in ext3_dirty_inode: Journal has aborted Oct 31 01:12:40 ota3g1 kernel: end_request: I/O error, dev sdi, sector 37757897 Oct 31 01:12:40 ota3g1 kernel: Buffer I/O error on device dm-12, logical block 1097 Oct 31 01:12:40 ota3g1 kernel: lost page write due to I/O error on dm-12 Oct 31 01:12:40 ota3g1 kernel: sd 8:0:0:4: SCSI error: return code = 0x00010000 Oct 31 01:12:40 ota3g1 kernel: end_request: I/O error, dev sdi, sector 283337089 Oct 31 01:12:40 ota3g1 kernel: Buffer I/O error on device dm-16, logical block 0 Oct 31 01:12:40 ota3g1 kernel: lost page write due to I/O error on dm-16 Oct 31 01:12:40 ota3g1 kernel: sd 8:0:0:4: SCSI error: return code = 0x00010000 Oct 31 01:12:40 ota3g1 kernel: EXT3-fs error (device dm-16) in ext3_dirty_inode: Journal has aborted Oct 31 01:12:40 ota3g1 kernel: end_request: I/O error, dev sdi, sector 37749121 Oct 31 01:12:40 ota3g1 kernel: Buffer I/O error on device dm-12, logical block 0 Oct 31 01:12:41 ota3g1 kernel: lost page write due to I/O error on dm-12 Oct 31 01:12:41 ota3g1 kernel: sd 8:0:0:4: SCSI error: return code = 0x00010000 Oct 31 01:12:41 ota3g1 kernel: end_request: I/O error, dev sdi, sector 283337089 Oct 31 01:12:41 ota3g1 kernel: Buffer I/O error on device dm-16, logical block 0 Oct 31 01:12:41 ota3g1 kernel: lost page write due to I/O error on dm-16 Oct 31 01:12:41 ota3g1 kernel: sd 8:0:0:4: SCSI error: return code = 0x00010000 df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/cciss-root 4.9G 730M 3.9G 16% / /dev/mapper/cciss-home 9.7G 1.2G 8.1G 13% /home /dev/mapper/cciss-var 9.7G 494M 8.8G 6% /var /dev/mapper/cciss-usr 15G 2.6G 12G 19% /usr /dev/mapper/cciss-tmp 3.9G 153M 3.6G 5% /tmp /dev/sda1 996M 43M 902M 5% /boot tmpfs 5.9G 0 5.9G 0% /dev/shm /dev/mapper/cciss-product 25G 16G 7.4G 68% /product /dev/mapper/cciss-opt 20G 4.5G 14G 25% /opt /dev/mapper/dg_db1-vol_db1_system 18G 2.2G 15G 14% /database/OTADB/sys /dev/mapper/dg_db1-vol_db1_undo 18G 5.8G 12G 35% /database/OTADB/undo /dev/mapper/dg_db1-vol_db1_redo 8.9G 4.3G 4.2G 51% /database/OTADB/redo /dev/mapper/dg_db1-vol_db1_sgbd 8.9G 654M 7.8G 8% /database/OTADB/admin /dev/mapper/dg_db1-vol_db1_arch 98G 24G 69G 26% /database/OTADB/arch /dev/mapper/dg_db1-vol_db1_indexes 240G 14G 214G 6% /database/OTADB/index /dev/mapper/dg_db1-vol_db1_data 275G 47G 215G 18% /database/OTADB/data /dev/mapper/dg_dbrman-vol_db_rman 8.9G 351M 8.1G 5% /database/RMAN /dev/mapper/dg_app1-vol_app1 151G 113G 31G 79% /files/ota /etc/fstab /dev/cciss/root / ext3 defaults 1 1 /dev/cciss/home /home ext3 defaults 1 2 /dev/cciss/var /var ext3 defaults 1 2 /dev/cciss/usr /usr ext3 defaults 1 2 /dev/cciss/tmp /tmp ext3 defaults 1 2 LABEL=/boot /boot ext3 defaults 1 2 tmpfs /dev/shm tmpfs defaults 0 0 devpts /dev/pts devpts gid=5,mode=620 0 0 sysfs /sys sysfs defaults 0 0 proc /proc proc defaults 0 0 /dev/cciss/swap swap swap defaults 0 0 /dev/cciss/product /product ext3 defaults 1 2 /dev/cciss/opt /opt ext3 defaults 1 2 /dev/dg_db1/vol_db1_system /database/OTADB/sys ext3 defaults 1 2 /dev/dg_db1/vol_db1_undo /database/OTADB/undo ext3 defaults 1 2 /dev/dg_db1/vol_db1_redo /database/OTADB/redo ext3 defaults 1 2 /dev/dg_db1/vol_db1_sgbd /database/OTADB/admin ext3 defaults 1 2 /dev/dg_db1/vol_db1_arch /database/OTADB/arch ext3 defaults 1 2 /dev/dg_db1/vol_db1_indexes /database/OTADB/index ext3 defaults 1 2 /dev/dg_db1/vol_db1_data /database/OTADB/data ext3 defaults 1 2 /dev/dg_dbrman/vol_db_rman /database/RMAN ext3 defaults 1 2 /dev/dg_app1/vol_app1 /files/ota ext3 defaults 1 2 Thanks for all the help.

    Read the article

  • How can I effectively block torrenting?

    - by Chauncellor
    My WNR1000v3 is serving six people and two of them have decided that despite my warnings they're going to torrent heavily all day. Not dealing with that crap I decided to reserve their IPs and set up port blocking 1000-65535 at all times of the day. However.... looking at the log reveals that stuff is still going through. Half of the entries are saying: [LAN access from remote] from <externalIP>:16001 to 192.168.1.7:18946 Friday, Oct 12,2012 22:47:05 and half are saying: [Service blocked: BlockTorrents] from source 192.168.1.7, Friday, Oct 12,2012 22:46:26 Is this because of uPNP? Or does the 'block services' feature Netgear has only work with outgoing connections? Is there something that I'm missing? If it is indeed uPNP, how could I effectively block their torrenting without hurting everyone's use of services like Skype, Playstation Network, etc.?

    Read the article

< Previous Page | 54 55 56 57 58 59 60 61 62 63 64 65  | Next Page >