Search Results

Search found 1696 results on 68 pages for 'textbook mistake'.

Page 58/68 | < Previous Page | 54 55 56 57 58 59 60 61 62 63 64 65  | Next Page >

• Ubuntu 11 and 12 initially fast but later bogs down, CPU pegged

  - by uos??

  I started with Ubuntu 11 a few weeks ago. It's on a DELL M4300 with a OCZ SSD. Default setup, except that I've installed the proprietary NVIDIA graphics and BROADCOM wireless drivers. Dual boot with Windows. If I cold boot into Ubuntu, it is very fast, just like the Windows experience that I'm used to. But SOMETHING happens, and I haven't yet determined what, but the system gets incredibly slow and stays that way. At first I thought it had to do with Adobe Flash because it seemed to be triggered by sites with Flash. But then I removed Flash and the problem remains. I thought it was just an overheating problem, but I've now upgraded to 12.04 which supposedly fixes the overheating problems I've read about. Perhaps the heat situation was brought on by Flash in my early cases? So I installed Jupiter for CPU management, but the thermometer reports a familiar Windows-side temperature of 53 degrees Celsius. Switching Jupiter to lower performance doesn't help. When I check the System Monitor application, sorting by CPU usage, there are no obvious problem processes. However, in the graphs tab, both CPU cores are pegged at 100%! I notice that the slowness seems to be similar to the extremely bad performance I got prior to installing the NVIDIA drivers. I'm not sure if that helps. This is the strangest part to me - although the temperature seems OK, even after rebooting, the system remains slow - starting with GRUB2 which is very noticeably delayed, all the way through to either Ubuntu or Windows! That's right, even the Windows side suffers effects and takes several minutes to complete booting whereas normally (with my SSD) it's ready to use in 15 seconds. The only way to fix it is to shutdown and let the parts cool down. Or maybe it just needs to completely power off and boot rather than a soft reboot, temperature has nothing to do with it? - is that possible? But know that I have never had this problem in Windows, even if Windows gets very hot (135 F) a reboot would be enough time for it to recover. For this reason, I don't think it's a heat thing, but I can't imagine what else could be surviving the reboot. I'm entirely updated - there are no pending updates. I have the Post-Release updates of NVIDIA too, btw. If this sounds CLOSE to something you know about, but one of the details doesn't line up exactly, it might be a mistake in my perception. Are there tests you can suggest to rule something out? Thanks! processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 23 model name : Intel(R) Core(TM)2 Duo CPU T9500 @ 2.60GHz stepping : 6 microcode : 0x60c cpu MHz : 800.000 cache size : 6144 KB physical id : 0 siblings : 2 core id : 0 cpu cores : 2 apicid : 0 initial apicid : 0 fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx lm constant_tsc arch_perfmon pebs bts rep_good nopl aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm sse4_1 lahf_lm ida dts tpr_shadow vnmi flexpriority bogomips : 5187.00 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 48 bits virtual power management: processor : 1 vendor_id : GenuineIntel cpu family : 6 model : 23 model name : Intel(R) Core(TM)2 Duo CPU T9500 @ 2.60GHz stepping : 6 microcode : 0x60c cpu MHz : 800.000 cache size : 6144 KB physical id : 0 siblings : 2 core id : 1 cpu cores : 2 apicid : 1 initial apicid : 1 fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx lm constant_tsc arch_perfmon pebs bts rep_good nopl aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm sse4_1 lahf_lm ida dts tpr_shadow vnmi flexpriority bogomips : 5186.94 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 48 bits virtual power management: (Redundant figures removed. You can view them in the edits if they are still relevant) ps: %CPU PID USER COMMAND 9.4 2399 jason gnome-terminal 6.2 2408 jason bash 17.3 1117 root /usr/bin/X :0 -auth /var/run/lightdm/root/:0 -nolisten tcp vt7 -novtswitch -background none 13.7 1667 jason compiz 1.3 1960 jason /usr/lib/unity/unity-panel-service 1.3 1697 jason python /usr/bin/jupiter 0.9 1964 jason /usr/lib/indicator-appmenu/hud-service 0.6 1689 jason nautilus -n 0.4 1458 jason //bin/dbus-daemon --fork --print-pid 5 --print-address 7 --session I should highlight specifically that GRUB2 can also be very slow. I don't know the relationship of which scenarios GRUB2 is also slow, but WHEN it is slow, it is slow both before the menu appears and after the selection is made - although for the diagnosis of GRUB2 it is harder for me to tell what the normal speeds should be. With SSD, I would expect that GRUB2 could load instantly, and that the GRUB2 purple would disappear instantly after the selection. The only delay to be expected is the change in graphics modes (though I couldn't guess why that ever requires any noticeable time)

  Read the article

• jQuery Selector Tester and Cheat Sheet

  - by SGWellens

  I've always appreciated these tools: Expresso and XPath Builder. They make designing regular expressions and XPath selectors almost fun! Did I say fun? I meant less painful. Being able to paste/load text and then interactively play with the search criteria is infinitely better than the code/compile/run/test cycle. It's faster and you get a much better feel for how the expressions work. So, I decided to make my own interactive tool to test jQuery selectors:  jQuery Selector Tester.   Here's a sneak peek: Note: There are some existing tools you may like better: http://www.woods.iki.fi/interactive-jquery-tester.html http://www.w3schools.com/jquery/trysel.asp?filename=trysel_basic&jqsel=p.intro,%23choose My tool is different: It is one page. You can save it and run it locally without a Web Server. It shows the results as a list of iterated objects instead of highlighted html. A cheat sheet is on the same page as the tester which is handy. I couldn't upload an .htm or .html file to this site so I hosted it on my personal site here: jQuery Selector Tester. Design Highlights: To make the interactive search work, I added a hidden div to the page: <!--Hidden div holds DOM elements for jQuery to search--><div id="HiddenDiv" style="display: none"></div> When ready to search, the searchable html text is copied into the hidden div…this renders the DOM tree in the hidden div: // get the html to search, insert it to the hidden divvar Html = $("#TextAreaHTML").val();$("#HiddenDiv").html(Html); When doing a search, I modify the search pattern to look only in the HiddenDiv. To do that, I put a space between the patterns.  The space is the Ancestor operator (see the Cheat Sheet): // modify search string to only search in our// hidden div and do the searchvar SearchString = "#HiddenDiv " + SearchPattern;try{    var $FoundItems = $(SearchString);}   Big Fat Stinking Faux Pas: I was about to publish this article when I made a big mistake: I tested the tool with Mozilla FireFox. It blowed up…it blowed up real good. In the past I’ve only had to target IE so this was quite a revelation. When I started to learn JavaScript, I was disgusted to see all the browser dependent code. Who wants to spend their time testing against different browsers and versions of browsers? Adding a bunch of ‘if-else’ code is a tedious and thankless task. I avoided client code as much as I could. Then jQuery came along and all was good. It was browser independent and freed us from the tedium of worrying about version N of the Acme browser. Right? Wrong! I had used outerHTML to display the selected elements. The problem is Mozilla FireFox doesn’t implement outerHTML. I replaced this: // encode the html markupvar OuterHtml = $('<div/>').text(this.outerHTML).html(); With this: // encode the html markupvar Html = $('<div>').append(this).html();var OuterHtml = $('<div/>').text(Html).html(); Another problem was that Mozilla FireFox doesn’t implement srcElement. I replaced this: var Row = e.srcElement.parentNode;  With this: var Row = e.target.parentNode; Another problem was the indexing. The browsers have different ways of indexing. I replaced this: // this cell has the search pattern  var Cell = Row.childNodes[1];   // put the pattern in the search box and search                    $("#TextSearchPattern").val(Cell.innerText);  With this: // get the correct cell and the text in the cell// place the text in the seach box and serachvar Cell = $(Row).find("TD:nth-child(2)");var CellText = Cell.text();$("#TextSearchPattern").val(CellText);   So much for the myth of browser independence. Was I overly optimistic and gullible? I don’t think so. And when I get my millions from the deposed Nigerian prince I sent money to, you’ll see that having faith is not futile. Notes: My goal was to have a single standalone file. I tried to keep the features and CSS to a minimum–adding only enough to make it useful and visually pleasing. When testing, I often thought there was a problem with the jQuery selector. Invariable it was invalid html code. If your results aren't what you expect, don't assume it's the jQuery selector pattern: The html may be invalid. To help in development and testing, I added a double-click handler to the rows in the Cheat Sheet table. If you double-click a row, the search pattern is put in the search box, a search is performed and the page is scrolled so you can see the results. I left the test html and code in the page. If you are using a CDN (non-local) version of the jQuery libraray, the designer in Visual Studio becomes extremely slow.  That's why there are two version of the library in the header and one is commented out. For reference, here is the jQuery documentation on selectors: http://api.jquery.com/category/selectors/ Here is a much more comprehensive list of CSS selectors (which jQuery uses): http://www.w3.org/TR/CSS2/selector.html I hope someone finds this useful. Steve WellensCodeProject

  Read the article

• Recover that Photo, Picture or File You Deleted Accidentally

  - by The Geek

  Have you ever accidentally deleted a photo on your camera, computer, USB drive, or anywhere else? What you might not know is that you can usually restore those pictures—even from your camera’s memory stick. Windows tries to prevent you from making a big mistake by providing the Recycle Bin, where deleted files hang around for a while—but unfortunately it doesn’t work for external USB drives, USB flash drives, memory sticks, or mapped drives. The great news is that this technique also works if you accidentally deleted the photo… from the camera itself. That’s what happened to me, and prompted writing this article. Restore that File or Photo using Recuva The first piece of software that you’ll want to try is called Recuva, and it’s extremely easy to use—just make sure when you are installing it, that you don’t accidentally install that stupid Yahoo! toolbar that nobody wants. Now that you’ve installed the software, and avoided an awful toolbar installation, launch the Recuva wizard and let’s start through the process of recovering those pictures you shouldn’t have deleted. The first step on the wizard page will let you tell Recuva to only search for a specific type of file, which can save a lot of time while searching, and make it easier to find what you are looking for. Next you’ll need to specify where the file was, which will obviously be up to wherever you deleted it from. Since I deleted mine from my camera’s SD card, that’s where I’m looking for it. The next page will ask you whether you want to do a Deep Scan. My recommendation is to not select this for the first scan, because usually the quick scan can find it. You can always go back and run a deep scan a second time. And now, you’ll see all of the pictures deleted from your drive, memory stick, SD card, or wherever you searched. Looks like what happened in Vegas didn’t stay in Vegas after all… If there are a really large number of results, and you know exactly when the file was created or modified, you can switch to the advanced view, where you can sort by the last modified time. This can help speed up the process quite a bit, so you don’t have to look through quite as many files. At this point, you can right-click on any filename, and choose to Recover it, and then save the files elsewhere on your drive. Awesome! Restore that File or Photo using DiskDigger If you don’t have any luck with Recuva, you can always try out DiskDigger, another excellent piece of software. I’ve tested both of these applications very thoroughly, and found that neither of them will always find the same files, so it’s best to have both of them in your toolkit. Note that DiskDigger doesn’t require installation, making it a really great tool to throw on your PC repair Flash drive. Start off by choosing the drive you want to recover from…   Now you can choose whether to do a deep scan, or a really deep scan. Just like with Recuva, you’ll probably want to select the first one first. I’ve also had much better luck with the regular scan, rather than the “dig deeper” one. If you do choose the “dig deeper” one, you’ll be able to select exactly which types of files you are looking for, though again, you should use the regular scan first. Once you’ve come up with the results, you can click on the items on the left-hand side, and see a preview on the right.  You can select one or more files, and choose to restore them. It’s pretty simple! Download DiskDigger from dmitrybrant.com Download Recuva from piriform.com Good luck recovering your deleted files! And keep in mind, DiskDigger is a totally free donationware software from a single, helpful guy… so if his software helps you recover a photo you never thought you’d see again, you might want to think about throwing him a dollar or two. Similar Articles Productive Geek Tips Stupid Geek Tricks: Undo an Accidental Move or Delete With a Keyboard ShortcutRestore Accidentally Deleted Files with RecuvaCustomize Your Welcome Picture Choices in Windows VistaAutomatically Resize Picture Attachments in Outlook 2007Resize Your Photos with Easy Thumbnails TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Icelandic Volcano Webcams Open Multiple Links At One Go NachoFoto Searches Images in Real-time Office 2010 Product Guides Google Maps Place marks – Pizza, Guns or Strip Clubs Monitor Applications With Kiwi

  Read the article

• The Krewe App Post-Mortem

  - by Chris Gardner

  Originally posted on: http://geekswithblogs.net/freestylecoding/archive/2014/05/23/the-krewe-app-post-mortem.aspxNow that teched has come and gone, I thought I would use this opportunity to do a little post-mortem on The Krewe app. It is one thing to test the app at home. It is a completely different animal to see how it responds in the environment TechEd creates. At a future time, I will list all the things that I would like to change with the app. At this point, I will find some good way to get community feedback. I want to break all this down screen by screen. We'll start with the screen I got right. The first of these is the events calendar. This is the one screen that, to you guys, just worked. However, there was an issue here. When I wrote v1 for last year, I was lazy and placed everything in CST. This caused problems with the achievements, which I will explain later. Furthermore, the event locations were not check-in locations. This created another problem with the achievements. Next, we get to the Twitter page. For what this page does, it works great. For those that don't know, I have an Azure Worker Role that polls Twitter pretty close to the rate limit. I cache these results in my database, and serve them upon request. This gives me great control over the content. I just have to remember to flush past tweets after a period, to save database growth. The next screen is the check-in screen. This screen has been the bane of my existence since I first created the thing. Last year, I used a background task to check people out of locations after they traveled. This year, I removed the background task in favor of a foursquare model. You are checked out after 3 hours or when you check-in to some other location. This seemed to work well, until those pesky achievements came into the mix. Again, more on this later. Next, I want to address the Connect and Connections screens together. I wanted to use some of the capabilities of the phone, and NFC seemed a natural choice. From this, I came up with the gamification aspects of the app. Since we are, fundamentally, a networking organization, I wanted to encourage people to actually network. Users could make and share a profile, similar to a virtual business card. I just had to figure out how to get people to use the feature. Why not just give someone a business card? Thus, the achievements were born. This was such a good idea. It would have been a great idea, if I have come up with it about two months earlier... When I came up with these ideas, I had about 2 weeks to implement them. Version 1 of the app was, basically, a pure consumption app. We provided data and centralized it. With version 2, the app became a much more interactive experience. The API was not ready for this change in such a short period of time. Most of this became apparent when I started implementing the achievements. The achievements based on count and specific person when fairly easy. The problem came with tying them to locations and events. This took some true SQL kung fu. This also showed me the rookie mistake of putting CST, not UTC, in the database. Once I got all of that cleaned up, I had to find a way to get the achievement system to talk to the phone. I knew I needed to be able to dynamically add achievements. I wouldn't know the precise location of some things until I got to Houston. I wanted the server to approve the achievements. This, unfortunately, required a decent data connection. Some achievements required GPS levels of location accuracy in areas of network triangulation. All of this became a huge nightmare. My flagship feature was based on some silly assumptions. Still, I managed to get 31 people to get the first achievement (Make 1 Connection.) Quite a few of those managed to get to the higher levels. Soon, I will post a list of the feature and changes that need to happen to the API. This includes things like proper objects for communication, geo-fencing, and caching. However, that is for another day.

  Read the article

• Tuning Red Gate: #4 of Some

  - by Grant Fritchey

  First time connecting to these servers directly (keys to the kingdom, bwa-ha-ha-ha. oh, excuse me), so I'm going to take a look at the server properties, just to see if there are any issues there. Max memory is set, cool, first possible silly mistake clear. In fact, these look to be nicely set up. Oh, I'd like to see the ANSI Standards set by default, but it's not a big deal. The default location for database data is the F:\ drive, where I saw all the activity last time. Cool, the people maintaining the servers in our company listen, parallelism threshold is set to 35 and optimize for ad hoc is enabled. No shocks, no surprises. The basic setup is appropriate. On to the problem database. Nothing wrong in the properties. The database is in SIMPLE recovery, but I think it's a reporting system, so no worries there. Again, I'd prefer to see the ANSI settings for connections, but that's the worst thing I can see. Time to look at the queries, tables, indexes and statistics because all the information I've collected over the last several days suggests that we're not looking at a systemic problem (except possibly not enough memory), but at the traditional tuning issues. I just want to note that, I started looking at the system, not the queries. So should you when tuning your environment. I know, from the data collected through SQL Monitor, what my top poor performing queries are, and the most frequently called, etc. I'm starting with the most frequently called. I'm going to get the execution plan for this thing out of the cache (although, with the cache dumping constantly, I might not get it). And it's not there. Called 1.3 million times over the last 3 days, but it's not in cache. Wow. OK. I'll see what's in cache for this database: SELECT  deqs.creation_time,         deqs.execution_count,         deqs.max_logical_reads,         deqs.max_elapsed_time,         deqs.total_logical_reads,         deqs.total_elapsed_time,         deqp.query_plan,         SUBSTRING(dest.text, (deqs.statement_start_offset / 2) + 1,                   (deqs.statement_end_offset - deqs.statement_start_offset) / 2                   + 1) AS QueryStatement FROM    sys.dm_exec_query_stats AS deqs         CROSS APPLY sys.dm_exec_sql_text(deqs.sql_handle) AS dest         CROSS APPLY sys.dm_exec_query_plan(deqs.plan_handle) AS deqp WHERE   dest.dbid = DB_ID('Warehouse') AND deqs.statement_end_offset > 0 AND deqs.statement_start_offset > 0 ORDER BY deqs.max_logical_reads DESC ; And looking at the most expensive operation, we have our first bad boy: Multiple table scans against very large sets of data and a sort operation. a sort operation? It's an insert. Oh, I see, the table is a heap, so it's doing an insert, then sorting the data and then inserting into the primary key. First question, why isn't this a clustered index? Let's look at some more of the queries. The next one is deceiving. Here's the query plan: You're thinking to yourself, what's the big deal? Well, what if I told you that this thing had 8036318 reads? I know, you're looking at skinny little pipes. Know why? Table variable. Estimated number of rows = 1. Actual number of rows. well, I'm betting several more than one considering it's read 8 MILLION pages off the disk in a single execution. We have a serious and real tuning candidate. Oh, and I missed this, it's loading the table variable from a user defined function. Let me check, let me check. YES! A multi-statement table valued user defined function. And another tuning opportunity. This one's a beauty, seriously. Did I also mention that they're doing a hash against all the columns in the physical table. I'm sure that won't lead to scans of a 500,000 row table, no, not at all. OK. I lied. Of course it is. At least it's on the top part of the Loop which means the scan is only executed once. I just did a cursory check on the next several poor performers. all calling the UDF. I think I found a big tuning opportunity. At this point, I'm typing up internal emails for the company. Someone just had their baby called ugly. In addition to a series of suggested changes that we need to implement, I'm also apologizing for being such an unkind monster as to question whether that third eye & those flippers belong on such an otherwise lovely child.

  Read the article

• SQL SERVER – Weekly Series – Memory Lane – #006

  - by pinaldave

  Here is the list of selected articles of SQLAuthority.com across all these years. Instead of just listing all the articles I have selected a few of my most favorite articles and have listed them here with additional notes below it. Let me know which one of the following is your favorite article from memory lane. 2006 This was my very first year of blogging so I was every day learning something new. As I have said many times, that blogging was never an intention. I had really not understood what exactly I am working on or beginning when I was beginning blogging in 2006. I had never knew that my life was going to change forever, once I started blogging. When I look back all of this year, I am happy that we are here together. 2007 IT Outsourcing to India – Top 10 Reasons Companies Outsource Outsourcing is about trust, collaboration and success. Helping other countries in need has been always the course of mankind, outsourcing is nothing different then that. With information technology and process improvements increasing the complexity, costs and skills required to accomplish routine tasks as well as challenging complex tasks, companies are outsourcing such tasks to providers who have the expertise to perform them at lower costs , with greater value and quality outcome. UDF – Remove Duplicate Chars From String This was a very interesting function I wrote in my early career. I am still using this function when I have to remove duplicate chars from strings. I have yet to come across a scenario where it does not work so I keep on using it till today. Please leave a comment if there is any better solution to this problem. FIX : Error : 3702 Cannot drop database because it is currently in use This is a very generic error when DROP Database is command is executed and the database is not dropped. The common mistake user is kept the connection open with this database and trying to drop the database. The database cannot be dropped if there is any other connection open along with it. It is always a good idea to take database in single user mode before dropping it. Here is the quick tutorial regarding how to bring the database in single user mode: Using T-SQL | Using SSMS. 2008 Install SQL Server 2008 – How to Upgrade to SQL Server 2008 – Installation Tutorial This was indeed one of the most popular articles in SQL Server 2008. Lots of people wanted to learn how to install SQL SErver 2008 but they were facing various issues while installation. I build this tutorial which becomes reference points for many. Default Collation of SQL Server 2008 What is the collation of SQL Server 2008 default installations? I often see this question confusing many experienced developers as well. Well the answer is in following image. Ahmedabad SQL Server User Group Meeting – November 2008 User group meetings are fun, now a days I am going to User Group meetings every week but there was a case when I have been just a beginner on this subject. The bug of the community was caught on me years ago when I started to present in Ahmedabad and Gandhinagar SQ LServer User Groups. 2009 Validate an XML document in TSQL using XSD My friend Jacob Sebastian wrote an excellent article on the subject XML and XSD. Because of the ‘eXtensible’ nature of XML (eXtensible Markup Language), often there is a requirement to restrict and validate the content of an XML document to a pre-defined structure and values. XSD (XML Schema Definition Language) is the W3C recommended language for describing and validating XML documents. SQL Server implements XSD as XML Schema Collections. Star Join Query Optimization At present, when queries are sent to very large databases, millions of rows are returned. Also the users have to go through extended query response times when joining multiple tables are involved with such queries. ‘Star Join Query Optimization’ is a new feature of SQL Server 2008 Enterprise Edition. This mechanism uses bitmap filtering for improving the performance of some types of queries by the effective retrieval of rows from fact tables. 2010 These puzzles are very interesting and intriguing – there was lots of interest on this subject. If you have free time this weekend. You may want to try them out. SQL SERVER – Challenge – Puzzle – Usage of FAST Hint (Solution)  SQL SERVER – Puzzle – Challenge – Error While Converting Money to Decimal (Solution)  SQL SERVER – Challenge – Puzzle – Why does RIGHT JOIN Exists (Open)  Additionally, I had great fun presenting SQL Server Performance Tuning seminar at fantastic locations in Hyderabad. Installing AdventeWorks Database This has been the most popular request I have received on my blog. Here is the quick video about how one can install AdventureWorks. 2011 Effect of SET NOCOUNT on @@ROWCOUNT There was an interesting incident once while I was presenting a session. I wrote a code and suddenly 10 hands went up in the air.  This was a bit surprise to me as I do not know why they all got alerted. I assumed that there should be something wrong with either project, screen or my display. However the real reason was very interesting – I suggest you read the complete blog post to understand this interesting scenario. Error: Deleting Offline Database and Creating the Same Name This is very interesting because once a user deletes the offline database the MDF and LDF file still exists and if the user attempts to create a new database with the same name it will give error. I found this very interesting and the blog explains the concept very quickly. Have you ever faced a similar situation? Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: Memory Lane, PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology

  Read the article

• Shadow mapping with deffered shading for directional lights - shadow map projection problem

  - by Harry

  I'm trying to implement shadow mapping to my engine. I started with directional lights because they seemed to be the easiest one, but I was wrong :) I have implemented deferred shading and I retrieve position from depth. I think that there is the biggest problem but code looks ok for me. Now more about problem: Shadow map projected onto meshes looks bad scaled and translated and also some informations from shadow map texture aren't visible. You can see it on this screen: http://img5.imageshack.us/img5/2254/93dn.png Yelow frustum is light frustum and I have mixed shadow map preview and actual scene. As you can see shadows are in wrong place and shadow of cone and sphere aren't visible. Could you look at my codes and tell me where I have a mistake? // create shadow map if(!_shd)glGenTextures(1, &_shd); glBindTexture(GL_TEXTURE_2D, _shd); glTexImage2D(GL_TEXTURE_2D, 0, GL_DEPTH_COMPONENT, 1024, 1024, 0, GL_DEPTH_COMPONENT, GL_FLOAT,NULL); // shadow map size glTexParameterf(GL_TEXTURE_2D, GL_TEXTURE_MAG_FILTER, GL_NEAREST); glTexParameterf(GL_TEXTURE_2D, GL_TEXTURE_MIN_FILTER, GL_NEAREST); glTexParameterf(GL_TEXTURE_2D, GL_TEXTURE_WRAP_S, GL_CLAMP_TO_EDGE); glTexParameterf(GL_TEXTURE_2D, GL_TEXTURE_WRAP_T, GL_CLAMP_TO_EDGE); glFramebufferTexture2D(GL_DRAW_FRAMEBUFFER, GL_DEPTH_ATTACHMENT, GL_TEXTURE_2D, _shd, 0); glDrawBuffer(GL_NONE); // setting camera Vector dire=Vector(0,0,1); ACamera.setLookAt(dire,Vector(0)); ACamera.setPerspectiveView(60.0f,1,0.1f,10.0f); // currently needed for proper frustum corners calculation Vector min(ACamera._point[0]),max(ACamera._point[0]); for(int i=0;i<8;i++){ max=Max(max,ACamera._point[i]); min=Min(min,ACamera._point[i]); } ACamera.setOrthogonalView(min.x,max.x,min.y,max.y,-max.z,-min.z); glBindFramebuffer(GL_DRAW_FRAMEBUFFER, _s_buffer); // framebuffer for shadow map // rendering to depth buffer glBindFramebuffer(GL_DRAW_FRAMEBUFFER, _g_buffer); Shaders["DirLight"].set(true); Matrix4 bias; bias.x.set(0.5,0.0,0.0,0.0); bias.y.set(0.0,0.5,0.0,0.0); bias.z.set(0.0,0.0,0.5,0.0); bias.w.set(0.5,0.5,0.5,1.0); Shaders["DirLight"].set("textureMatrix",ACamera.matrix*Projection3D*bias); // order of multiplications are 100% correct, everything gives mi the same result as using glm glActiveTexture(GL_TEXTURE5); glBindTexture(GL_TEXTURE_2D,_shd); lightDir(dir); // light calculations Vertex Shader makes nothing related to shadow calculatons Pixel shader function which calculates if pixel is in shadow or not: float readShadowMap(vec3 eyeDir) { // retrieve depth of pixel float z = texture2D(depth, gl_FragCoord.xy/screen).z; vec3 pos = vec3(gl_FragCoord.xy/screen, z); // transform by the projection and view inverse vec4 worldSpace = inverse(View)*inverse(ProjectionMatrix)*vec4(pos*2-1,1); worldSpace /= worldSpace.w; vec4 coord=textureMatrix*worldSpace; float vis=1.0f; if(texture2D(shadow, coord.xy).z < coord.z-0.001)vis=0.2f; return vis; } I also have question about shadows specifically for directional light. Currently I always look at 0,0,0 position and in further implementation I have to move light frustum along to camera frustum. I've found how to do this here: http://www.gamedev.net/topic/505893-orthographic-projection-for-shadow-mapping/ but it doesn't give me what I want. Maybe because of problems mentioned above, but I want know your opinion. EDIT: vec4 worldSpace is position read from depht of the scene (not shadow map). Maybe I wasn't precise so I'll try quick explain what is what: View is camera view matrix, ProjectionMatrix is camera projection,. First I try to get world space position from depth map and then multiply it by textureMatrix which is light view *light projection*bias. Rest of code is the same as in many tutorials. I can't use vertex shader to make something like gl_Position=textureMatrix*gl_Vertex and get it interpolated in fragment shader because of deffered rendering use so I want get it from depht buffer. EDIT2: I also tried make it as in Coding Labs tutorial about Shadow Mapping with Deferred Rendering but unfortunately this either works wrong.

  Read the article

• So you want a French Site?

  - by juanlarios

  I thought I would write a quick write up of how to create a french site in SharePoint 2007. I'm not talking about a Variation but just a plain French Site from the ground up. There were some gotchas that I felt were worth blogging about. First:  go to Microsoft Telnet Article and follow the install instructions. Make sure that when you get to the download page that you select "French" as part of the drop down and you download and install the right language pack. I noticed that if you did not click the "change" button enven though I selected the 'french' language pack, it reverted back to the english language pack.   Second: You will notice a couple of things. When you go to central admin you will see the following:    Now you can pick between french site or english. You will get this if you install other language packs and they will be listed in the drop down. You will notice that you now have french headings and frech listings of sites. You see "Publishing" as a heading because I have a custom site definition that I deployed as a french site. Third: As you start navigating around and trying to create document libraries or sites you will start getting errors. Errors like the following: "Cannot make a cache safe URL for "SelectorControls.js", file not found. Please verify that the file exists under the layouts directory. " Troubleshoot issues with Windows SharePoint Services. Once you resolve the issue with this "js" file, you will find that there are other js files that are missing. The only problem is that if you are not fluent in French or the language you are trying to deploy, Well, you'll have a tough time understanding error messages as they will all be in the new language you are trying to deploy. So let's just talk about what happened when you installed the language pack. In the 12 Hive:  12/Template    you will now see a 1033 folder and a 1036 folder. The 1036 folder is the folder that was created and added as part of the language pack. What the above error is saying is that now that it's looking at the 1036 folder, well, it's missing some files. The nice thing is that these files are included in the 1033 folder (which is the English Language Pack). Simply copy and paste the controls from the one folder to the other. There will be more than one conflict so you will have to move serveral controls over. Can't remember how many but simply add them as error messages come up. I had to add some navigation controls and some content selectors.   Now that's all that you need to install the Frech Language pack anc reate site collections that are entirely in a another language. Do not mistake this with Variations, where you can have multiple language sites. For those of you doing a little bit extra with this, let me share what I was doing extra and what I needed to get it working for me. I had had a custom site definition which was obviously not showing up in my selection of french sites. I was under the impression that all sites in English would show up in french and that the sites were simply routed to a new Resource file for french content. And that is the case but there is a little extra that needs to be done if you have a custom site definition deployed:  First: Under hive 12/Template/1033/XML  there is a listing of site definition files that are deployed to the English side of things. If you navigate to 12/Template/1036/XML  and open one of the site definitions you will see that they are similar and reference the existing site definitions installed on the server, except that they have some french added to descriptions and names. Simply copy the xml file of your custom template to the 1036 folder to have it show up as a selection when you select French as the dropdown entry when create a site colleciton. You can go ahead and change the description and name to suit the language it's under.    Second: As part of my site definition, I packaed up several list templates, that were saved as STP files. When you navigate to the list template listing, well, the templates are for English sites, not French so I cannot create document libraries based on the template. What now? well here comes KWIzCom to the rescue! They seem to have put out a "STP language converter" where you can take a site template or list template and convert it to any target language you are after. It's a free download, Use it and you're good to go.  One thing I will mention is that when I convereted the English documents I whent ahead and converted them to French-Canadien. And it didn't work! so I finally figured out that the French Version it was expecting in the french site was "French-France". Don't know why that is, it's just what needs to be done to get that working. When I did that, I was able to use the List templates that I created in the English site for the French Site.   Hope it helps , good luck!

  Read the article

• SQL SERVER – Recover the Accidentally Renamed Table

  - by pinaldave

  I have no answer to following question. I saw a desperate email marked as urgent delivered in my mailbox. “I accidentally renamed table in my SSMS. I was scrolling very fast and I made mistakes. It was either because I double clicked or clicked on F2 (shortcut key for renaming). However, I have made the mistake and now I have no idea how to fix this. I am in big trouble. Help me get my original tablename.” I have seen many similar scenarios in my life and they give me a very good opportunity to preach wisdom but when the house is burning, we cannot talk about how we should have conserved the water earlier. The goal at that point is to put off the fire as fast as we can. I decided to answer this email with my best knowledge. If you have renamed the table, I think you pretty much is out of luck. Here are few things which you can do which can give you idea about what your tablename can be if you are lucky. Method 1: (Not Recommended but try your luck) Check your naming convention of your system. I have often seen that many organizations name their index as IX_TableName_Colms or name their keys as FK_TableName1_TableName2_Cols. If your organization is following the same you can get the name from your table, you may refer your keys. Again, note that this is quite possible that your tablename was already renamed and your keys were not updated. This can easily lead you to select incorrect name. I think follow this if you are confident or move to the next method. Method 2: (Not Recommended but try your luck) This method is also based on your orgs naming convention. If you use the name of the table in any columnname (some organizations use tablename in their incremental identity column name), you can get that name from there. Method 3: (Not Recommended but try your luck) If you know where your table was used in your stored procedures, you can script your stored procedure and find the name of the table back. Method 4: (Try your luck) All the best organizations first create a data model of the schema and there is good chance that this table is used there, you should take your chances and refer original document. If your organization is good at managing docs or source code, you will get the name of the table back for sure. Method 5: (It WORKS but try on a development server) There is no sure way to get you the name of the table which you accidentally renamed however, there is one way which will work for sure. You need to take your latest full backup and restore it on your development server (remember not on production or where you have renamed this column). Now restore latest differential file of the full backup. Now restore all the log files one by one making sure that you are restoring before the point of time of you renamed the tablename. Now go to explore and this will give you the name of the table which you have renamed. If you are confident that the same table existed with the same name when the last full backup was made, you do not have to go to all the steps. You can just get the name of the table directly from last backup’s restore. Read the article about Backup Timeline. Wisdom: How can I miss to preach wisdom when I get the opportunity to do so? Here are a few points to remember. Use a different account to explore production environment. Do not use the same account which have all the rights and permissions all the time. Use the account which has read only permissions if there are no modification required. Use policy based management to prevent changes which are accidental. If there was policy of valid names, the accidental change of the table was not possible unless it was intentional delibarate changes. Have a proper auditing of the system in place. You can use DDL triggers but be careful with its usage (get it reviewed properly first). (Add your suggestion here) I guess Method 5 will work all the time (using point in time restore). Everything else is chance of luck and if you are lucky are bad – you will get further incorrect name. Now go back and read the first line of this blog. Out of five method four methods are just lucky guesses. The method 5 will work but again it is a lengthy process if the size of the database is huge or if you do not have full backup. Did I miss anything obvious? Please leave a comment and I will publish your answer with due credit. Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: PostADay, SQL, SQL Authority, SQL Puzzle, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology

  Read the article

• Threads are facing deadlock in socket program [migrated]

  - by ankur.trapasiya

  I am developing one program in which a user can download a number of files. Now first I am sending the list of files to the user. So from the list user selects one file at a time and provides path where to store that file. In turn it also gives the server the path of file where does it exist. I am following this approach because I want to give stream like experience without file size limitation. Here is my code.. 1) This is server which gets started each time I start my application public class FileServer extends Thread { private ServerSocket socket = null; public FileServer() { try { socket = new ServerSocket(Utils.tcp_port); } catch (IOException e) { // TODO Auto-generated catch block e.printStackTrace(); } } @Override public void run() { try { System.out.println("request received"); new FileThread(socket.accept()).start(); } catch (IOException ex) { ex.printStackTrace(); } } } 2) This thread runs for each client separately and sends the requested file to the user 8kb data at a time. public class FileThread extends Thread { private Socket socket; private String filePath; public String getFilePath() { return filePath; } public void setFilePath(String filePath) { this.filePath = filePath; } public FileThread(Socket socket) { this.socket = socket; System.out.println("server thread" + this.socket.isConnected()); //this.filePath = filePath; } @Override public void run() { // TODO Auto-generated method stub try { ObjectInputStream ois=new ObjectInputStream(socket.getInputStream()); try { //************NOTE filePath=(String) ois.readObject(); } catch (ClassNotFoundException e) { // TODO Auto-generated catch block e.printStackTrace(); } File f = new File(this.filePath); byte[] buf = new byte[8192]; InputStream is = new FileInputStream(f); BufferedInputStream bis = new BufferedInputStream(is); ObjectOutputStream oos = new ObjectOutputStream( socket.getOutputStream()); int c = 0; while ((c = bis.read(buf, 0, buf.length)) > 0) { oos.write(buf, 0, c); oos.flush(); // buf=new byte[8192]; } oos.close(); //socket.shutdownOutput(); // client.shutdownOutput(); System.out.println("stop"); // client.shutdownOutput(); ois.close(); // Thread.sleep(500); is.close(); bis.close(); socket.close(); } catch (IOException ex) { ex.printStackTrace(); } } } NOTE: here filePath represents the path of the file where it exists on the server. The client who is connecting to the server provides this path. I am managing this through sockets and I am successfully receiving this path. 3) FileReceiverThread is responsible for receiving the data from the server and constructing file from this buffer data. public class FileReceiveThread extends Thread { private String fileStorePath; private String sourceFile; private Socket socket = null; public FileReceiveThread(String ip, int port, String fileStorePath, String sourceFile) { this.fileStorePath = fileStorePath; this.sourceFile = sourceFile; try { socket = new Socket(ip, port); System.out.println("receive file thread " + socket.isConnected()); } catch (IOException ex) { ex.printStackTrace(); } } @Override public void run() { try { ObjectOutputStream oos = new ObjectOutputStream( socket.getOutputStream()); oos.writeObject(sourceFile); oos.flush(); // oos.close(); File f = new File(fileStorePath); OutputStream os = new FileOutputStream(f); BufferedOutputStream bos = new BufferedOutputStream(os); byte[] buf = new byte[8192]; int c = 0; //************ NOTE ObjectInputStream ois = new ObjectInputStream( socket.getInputStream()); while ((c = ois.read(buf, 0, buf.length)) > 0) { // ois.read(buf); bos.write(buf, 0, c); bos.flush(); // buf = new byte[8192]; } ois.close(); oos.close(); // os.close(); bos.close(); socket.close(); //Thread.sleep(500); } catch (IOException ex) { ex.printStackTrace(); } } } NOTE : Now the problem that I am facing is at the first time when the file is requested the outcome of the program is same as my expectation. I am able to transmit any size of file at first time. Now when the second file is requested (e.g. I have sent file a,b,c,d to the user and user has received file a successfully and now he is requesting file b) the program faces deadlock at this situation. It is waiting for socket's input stream. I put breakpoint and tried to debug it but it is not going in FileThread's run method second time. I could not find out the mistake here. Basically I am making a LAN Messenger which works on LAN. I am using SWT as UI framework.

  Read the article

• SQL SERVER – Curious Case of Disappearing Rows – ON UPDATE CASCADE and ON DELETE CASCADE – Part 1 of 2

  - by pinaldave

  Social media has created an Always Connected World for us. Recently I enrolled myself to learn new technologies as a student. I had decided to focus on learning and decided not to stay connected on the internet while I am in the learning session. On the second day of the event after the learning was over, I noticed lots of notification from my friend on my various social media handle. He had connected with me on Twitter, Facebook, Google+, LinkedIn, YouTube as well SMS, WhatsApp on the phone, Skype messages and not to forget with a few emails. I right away called him up. The problem was very unique – let us hear the problem in his own words. “Pinal – we are in big trouble we are not able to figure out what is going on. Our product details table is continuously loosing rows. Lots of rows have disappeared since morning and we are unable to find why the rows are getting deleted. We have made sure that there is no DELETE command executed on the table as well. The matter of the fact, we have removed every single place the code which is referencing the table. We have done so many crazy things out of desperation but no luck. The rows are continuously deleted in a random pattern. Do you think we have problems with intrusion or virus?” After describing the problems he had pasted few rants about why I was not available during the day. I think it will be not smart to post those exact words here (due to many reasons). Well, my immediate reaction was to get online with him. His problem was unique to him and his team was all out to fix the issue since morning. As he said he has done quite a lot out in desperation. I started asking questions from audit, policy management and profiling the data. Very soon I realize that I think this problem was not as advanced as it looked. There was no intrusion, SQL Injection or virus issue. Well, long story short first - It was a very simple issue of foreign key created with ON UPDATE CASCADE and ON DELETE CASCADE.  CASCADE allows deletions or updates of key values to cascade through the tables defined to have foreign key relationships that can be traced back to the table on which the modification is performed. ON DELETE CASCADE specifies that if an attempt is made to delete a row with a key referenced by foreign keys in existing rows in other tables, all rows containing those foreign keys are also deleted. ON UPDATE CASCADE specifies that if an attempt is made to update a key value in a row, where the key value is referenced by foreign keys in existing rows in other tables, all of the foreign key values are also updated to the new value specified for the key. (Reference: BOL) In simple words – due to ON DELETE CASCASE whenever is specified when the data from Table A is deleted and if it is referenced in another table using foreign key it will be deleted as well. In my friend’s case, they had two tables, Products and ProductDetails. They had created foreign key referential integrity of the product id between the table. Now the as fall was up they were updating their catalogue. When they were updating the catalogue they were deleting products which are no more available. As the changes were cascading the corresponding rows were also deleted from another table. This is CORRECT. The matter of the fact, there is no error or anything and SQL Server is behaving how it should be behaving. The problem was in the understanding and inappropriate implementations of business logic.  What they needed was Product Master Table, Current Product Catalogue, and Product Order Details History tables. However, they were using only two tables and without proper understanding the relation between them was build using foreign keys. If there were only two table, they should have used soft delete which will not actually delete the record but just hide it from the original product table. This workaround could have got them saved from cascading delete issues. I will be writing a detailed post on the design implications etc in my future post as in above three lines I cannot cover every issue related to designing and it is also not the scope of the blog post. More about designing in future blog posts. Once they learn their mistake, they were happy as there was no intrusion but trust me sometime we are our own enemy and this is a great example of it. In tomorrow’s blog post we will go over their code and workarounds. Feel free to share your opinions, experiences and comments. Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology

  Read the article

• How to Tell If Your Computer is Overheating and What to Do About It

  - by Chris Hoffman

  Heat is a computer’s enemy. Computers are designed with heat dispersion and ventilation in mind so they don’t overheat. If too much heat builds up, your computer may become unstable or suddenly shut down. The CPU and graphics card produce much more heat when running demanding applications. If there’s a problem with your computer’s cooling system, an excess of heat could even physically damage its components. Is Your Computer Overheating? When using a typical computer in a typical way, you shouldn’t have to worry about overheating at all. However, if you’re encountering system instability issues like abrupt shut downs, blue screens, and freezes — especially while doing something demanding like playing PC games or encoding video — your computer may be overheating. This can happen for several reasons. Your computer’s case may be full of dust, a fan may have failed, something may be blocking your computer’s vents, or you may have a compact laptop that was never designed to run at maximum performance for hours on end. Monitoring Your Computer’s Temperature First, bear in mind that different CPUs and GPUs (graphics cards) have different optimal temperature ranges. Before getting too worried about a temperature, be sure to check your computer’s documentation — or its CPU or graphics card specifications — and ensure you know the temperature ranges your hardware can handle. You can monitor your computer’s temperatures in a variety of different ways. First, you may have a way to monitor temperature that is already built into your system. You can often view temperature values in your computer’s BIOS or UEFI settings screen. This allows you to quickly see your computer’s temperature if Windows freezes or blue screens on you — just boot the computer, enter the BIOS or UEFI screen, and check the temperatures displayed there. Note that not all BIOSes or UEFI screens will display this information, but it is very common. There are also programs that will display your computer’s temperature. Such programs just read the sensors inside your computer and show you the temperature value they report, so there are a wide variety of tools you can use for this, from the simple Speccy system information utility to an advanced tool like SpeedFan. HWMonitor also offer this feature, displaying a wide variety of sensor information. Be sure to look at your CPU and graphics card temperatures. You can also find other temperatures, such as the temperature of your hard drive, but these components will generally only overheat if it becomes extremely hot in the computer’s case. They shouldn’t generate too much heat on their own. If you think your computer may be overheating, don’t just glance as these sensors once and ignore them. Do something demanding with your computer, such as running a CPU burn-in test with Prime 95, playing a PC game, or running a graphical benchmark. Monitor the computer’s temperature while you do this, even checking a few hours later — does any component overheat after you push it hard for a while? Preventing Your Computer From Overheating If your computer is overheating, here are some things you can do about it: Dust Out Your Computer’s Case: Dust accumulates in desktop PC cases and even laptops over time, clogging fans and blocking air flow. This dust can cause ventilation problems, trapping heat and preventing your PC from cooling itself properly. Be sure to clean your computer’s case occasionally to prevent dust build-up. Unfortunately, it’s often more difficult to dust out overheating laptops. Ensure Proper Ventilation: Put the computer in a location where it can properly ventilate itself. If it’s a desktop, don’t push the case up against a wall so that the computer’s vents become blocked or leave it near a radiator or heating vent. If it’s a laptop, be careful to not block its air vents, particularly when doing something demanding. For example, putting a laptop down on a mattress, allowing it to sink in, and leaving it there can lead to overheating — especially if the laptop is doing something demanding and generating heat it can’t get rid of. Check if Fans Are Running: If you’re not sure why your computer started overheating, open its case and check that all the fans are running. It’s possible that a CPU, graphics card, or case fan failed or became unplugged, reducing air flow. Tune Up Heat Sinks: If your CPU is overheating, its heat sink may not be seated correctly or its thermal paste may be old. You may need to remove the heat sink and re-apply new thermal paste before reseating the heat sink properly. This tip applies more to tweakers, overclockers, and people who build their own PCs, especially if they may have made a mistake when originally applying the thermal paste. This is often much more difficult when it comes to laptops, which generally aren’t designed to be user-serviceable. That can lead to trouble if the laptop becomes filled with dust and needs to be cleaned out, especially if the laptop was never designed to be opened by users at all. Consult our guide to diagnosing and fixing an overheating laptop for help with cooling down a hot laptop. Overheating is a definite danger when overclocking your CPU or graphics card. Overclocking will cause your components to run hotter, and the additional heat will cause problems unless you can properly cool your components. If you’ve overclocked your hardware and it has started to overheat — well, throttle back the overclock! Image Credit: Vinni Malek on Flickr     

  Read the article

• Checksum Transformation

  The Checksum Transformation computes a hash value, the checksum, across one or more columns, returning the result in the Checksum output column. The transformation provides functionality similar to the T-SQL CHECKSUM function, but is encapsulated within SQL Server Integration Services, for use within the pipeline without code or a SQL Server connection. As featured in The Microsoft Data Warehouse Toolkit by Joy Mundy and Warren Thornthwaite from the Kimbal Group. Have a look at the book samples especially Sample package for custom SCD handling. All input columns are passed through the transformation unaltered, those selected are used to generate the checksum which is passed out through a single output column, Checksum. This does not restrict the number of columns available downstream from the transformation, as columns will always flow through a transformation. The Checksum output column is in addition to all existing columns within the pipeline buffer. The Checksum Transformation uses an algorithm based on the .Net framework GetHashCode method, it is not consistent with the T-SQL CHECKSUM() or BINARY_CHECKSUM() functions. The transformation does not support the following Integration Services data types, DT_NTEXT, DT_IMAGE and DT_BYTES. ChecksumAlgorithm Property There ChecksumAlgorithm property is defined with an enumeration. It was first added in v1.3.0, when the FrameworkChecksum was added. All previous algorithms are still supported for backward compatibility as ChecksumAlgorithm.Original (0). Original - Orginal checksum function, with known issues around column separators and null columns. This was deprecated in the first SQL Server 2005 RTM release. FrameworkChecksum - The hash function is based on the .NET Framework GetHash method for object types. This is based on the .NET Object.GetHashCode() method, which unfortunately differs between x86 and x64 systems. For that reason we now default to the CRC32 option. CRC32 - Using a standard 32-bit cyclic redundancy check (CRC), this provides a more open implementation. The component is provided as an MSI file, however to complete the installation, you will have to add the transformation to the Visual Studio toolbox by hand. This process has been described in detail in the related FAQ entry for How do I install a task or transform component?, just select Checksum from the SSIS Data Flow Items list in the Choose Toolbox Items window. Downloads The Checksum Transformation is available for SQL Server 2005, SQL Server 2008 (includes R2) and SQL Server 2012. Please choose the version to match your SQL Server version, or you can install multiple versions and use them side by side if you have more than one version of SQL Server installed. Checksum Transformation for SQL Server 2005 Checksum Transformation for SQL Server 2008 Checksum Transformation for SQL Server 2012 Version History SQL Server 2012 Version 3.0.0.27 – SQL Server 2012 release. Includes upgrade support for both 2005 and 2008 packages to 2012. (5 Jun 2010) SQL Server 2008 Version 2.0.0.27 – Fix for CRC-32 algorithm that inadvertently made it sort dependent. Fix for race condition which sometimes lead to the error Item has already been added. Key in dictionary: '79764919' . Fix for upgrade mappings between 2005 and 2008. (19 Oct 2010) Version 2.0.0.24 - SQL Server 2008 release. Introduces the new CRC-32 algorithm, which is consistent across x86 and x64.. The default algorithm is now CRC32. (29 Oct 2008) Version 2.0.0.6 - SQL Server 2008 pre-release. This version was released by mistake as part of the site migration, and had known issues. (20 Oct 2008) SQL Server 2005 Version 1.5.0.43 – Fix for CRC-32 algorithm that inadvertently made it sort dependent. Fix for race condition which sometimes lead to the error Item has already been added. Key in dictionary: '79764919' . (19 Oct 2010) Version 1.5.0.16 - Introduces the new CRC-32 algorithm, which is consistent across x86 and x64. The default algorithm is now CRC32. (20 Oct 2008) Version 1.4.0.0 - Installer refresh only. (22 Dec 2007) Version 1.4.0.0 - Refresh for minor UI enhancements. (5 Mar 2006) Version 1.3.0.0 - SQL Server 2005 RTM. The checksum algorithm has changed to improve cardinality when calculating multiple column checksums. The original algorithm is still available for backward compatibility. Fixed custom UI bug with Output column name not persisting. (10 Nov 2005) Version 1.2.0.1 - SQL Server 2005 IDW 15 June CTP. A user interface is provided, as well as the ability to change the checksum output column name. (29 Aug 2005) Version 1.0.0 - Public Release (Beta). (30 Oct 2004) Screenshot

  Read the article

• Seven Random Thoughts on JavaOne

  - by HecklerMark

  As most people reading this blog may know, last week was JavaOne. There are a lot of summary/recap articles popping up now, and while I didn't want to just "add to pile", I did want to share a few observations. Disclaimer: I am an Oracle employee, but most of these observations are either externally verifiable or based upon a collection of opinions from Oracle and non-Oracle attendees alike. Anyway, here are a few take-aways: The Java ecosystem is alive and well, with a breadth and depth that is impossible to adequately describe in a short post...or a long post, for that matter. If there is any one area within the Java language or JVM that you would like to - or need to - know more about, it's well-represented at J1. While there are several IDEs that are used to great effect by the developer community, NetBeans is on a roll. I lost count how many sessions mentioned or used NetBeans, but it was by far the dominant IDE in use at J1. As a recent re-convert to NetBeans, I wasn't surprised others liked it so well, only how many. OpenJDK, OpenJFX, etc. Many developers were understandably concerned with the change of sponsorship/leadership when Java creator and longtime steward Sun Microsystems was acquired by Oracle. The read I got from attendees regarding Oracle's stewardship was almost universally positive, and the push for "openness" is deep and wide within the current Java environs. Few would probably have imagined it to be this good, this soon. Someone observed that "Larry (Ellison) is competitive, and he wants to be the best...so if he wants to have a community, it will be the best community on the planet." Like any company, Oracle is bound to make missteps, but leadership seems to be striking an excellent balance between embracing open efforts and innovating in competitive paid offerings. JavaFX (2.x) isn't perfect or comprehensive, but a great many people (myself included) see great potential, are developing for it, and are really excited about where it is and where it may be headed. This is another part of the Java ecosystem that has impressive depth for being so new (JavaFX 1.x aside). If you haven't kicked the tires yet, give it a try! You'll be surprised at how capable and versatile it is, and you'll probably catch yourself smiling while coding again.  :-) JavaEE is everywhere. Not exactly a newsflash, but there is a lot of buzz around EE still/again/anew. Sessions ranged from updated component specs/technologies to Websockets/HTML5, from frameworks to profiles and application servers. Programming "server-side" Java isn't confined to the server (as you no doubt realize), and if you still consider JavaEE a cumbersome beast, you clearly haven't been using the last couple of versions. Download GlassFish or the WebLogic Zip distro (or another JavaEE 6 implementation) and treat yourself. JavaOne is not inexpensive, but to paraphrase an old saying, "If you think that's expensive, you should try ignorance." :-) I suppose it's possible to attend J1 and learn nothing, but you'd have to really work at it! Attending even a single session is bound to expand your horizons and make you approach your code, your problem domain, differently...even if it's a session about something you already know quite well. The various presenters offer vastly different perspectives and challenge you to re-think your own approach(es). And finally, if you think the scheduled sessions are great - and make no mistake, most are clearly outstanding - wait until you see what you pick up from what I like to call the "hallway sessions". Between the presentations, people freely mingle in the hallways, go to lunch and dinner together, and talk. And talk. And talk. Ideas flow freely, sparking other ideas and the "crowdsourcing" of knowledge in a way that is hard to imagine outside of a conference of this magnitude. Consider this the "GO" part of a "BOGO" (Buy One, Get One) offer: you buy the ticket to the "structured" part of JavaOne and get the hallway sessions at no additional charge. They're really that good. If you weren't able to make it to JavaOne this year, you can still watch/listen to the sessions online by visiting the JavaOne course catalog and clicking the media link(s) in the right column - another demonstration of Oracle's commitment to the Java community. But make plans to be there next year to get the full benefit! You'll be glad you did. All the best,Mark P.S. - I didn't mention several other exciting developments in areas like the embedded space and the "internet of things" (M2M), robotics, optimization, and the cloud (among others), but I think you get the idea. JavaOne == brainExpansion;  Hope to see you there next year!

  Read the article

• jQuery with SharePoint solutions

  - by KunaalKapoor

  For me jQuery is the 'Plan-B' for everything.And most of my projects include the use of jQuery for something or the other, so I decided to write a small note on what works best while using jQuery along with SharePoint.I prefer to use the jQuery JavaScript library, which is far more robust, easier to use, and allows for plugins. Follow the steps below to add jQuery to your master page. For office 365, the prefered location to add jQuery files is the "Site Asserts" library.Deployment Best PracticesThey are only as good as the context it’s being referenced.  In other words, take into account your world before applying it.Script your deployment options.  Folder in SPD. Use the file system.  Make external references.  The JQuery library is on the Microsoft Ajax Content Delivery Network. You may even choose to publish to and from the document library. (pros and cons to this approach)Reference options when referencing the script.ScriptLink will make sure it’s loaded at the top of the page and only loaded once. You need Visual Studio or SPDContent Editor Web Part (CEWP).  Drop it on the page and it’s there.  Easy but dangerousCustom Actions. Great for global deployments of JQuery.  Loads it on every page. It also works in Sandbox installations.Deployment Maintenance Dont’sDon’t add scripts directly to your Master Page. That’s way too much effort because the pages are hard to maintain.Don’t add scripts directly to the CEWP.  Use a content link instead. That will allow for reuse. If you or someone deletes the CEWP you won’t lose code in the web partSecurity.  Any scripts run with the same privileges of the current user.  In other words, you can’t get in trouble.Development Best PracticesDon’t abuse the DOM.  There are better options to load the DOM without hitting it 1,000 times.User other performance boosters.Try other libraries.  Try some custom codeAvoid String conversionMinify your filesUse CAML to reduce number of returns rowsOnly update your JQuery library AFTER RIGOROUS REGRESSION TESTINGCRUD operations can come with some funSP Services wraps SharePoint’s web services for executionThe Bing SDK is pretty easy to use.  You can add it to your page with a script,  put it into a content editor web part and connect it from the address parameters in a list.Steps:1. Go to jquery.com and download the latest jQuery library to your desktop. You want to get the compressed production version, not the development version.2. Open SharePoint Designer (SPD) and connect to the root level of your site's site collection.In SPD, open the "Style Library" folder. Create a folder named "Scripts" inside of the Style Library. Drag the jQuery library JavaScript file from your desktop into the Scripts folder.In the Scripts folder, create a new JavaScript file and name it (e.g. "actions.js").3. If you are using visual studio add a folder for js, you can create a new folder at the root level or if you prefer more cleaner solutions like me, you can use the layouts folder which cleans out on deactivation/uninstall.4. Within the <head> tag of the master page, add a script reference to the jQuery library just above the content place holder named "PlaceHolderAdditonalPageHead" (and above your custom CSS references, if applicable) as follows:<script src="/Style%20Library/Scripts/{jquery library file}.js" type="text/javascript"></script>Immediately after the jQuery library reference add a script reference to your custom scripts file as follows:<script src="/Style%20Library/Scripts/actions.js" type="text/javascript"></script>Inside your script tag, you can test if jQuery is already defined and if not, then add it to the page.<script type='text/javascript'>  if (typeof jQuery == 'undefined')    document.write('<scr'+'ipt type="text/javascript" src="http://code.jquery.com/jquery-1.6.1.min.js"></sc'+'ript>');</script>For the inquisitive few... Read on if you'd like :)Why jQuery on SharePoiny is AwesomeIt’s all about that visual wow factor.  You can get past that, “But it looks like SharePoint”  Take a long list view and put it into JQuery with pagination, etc and you are the hero.  It’s also about new controls you get with JQuery that you couldn’t do before.Why jQuery with SharePoint should be AwfulAlthough it’s fairly easy to get jQuery up and running. Copy/Paste can cause a problem.  If you don’t understand what it’s doing in the Client Object Model and the Document Object Model then it will do things on your site that were completely unexpected. Many blogs will note workarounds they employed on their sites. Why it’s not working: Debugging “sucks”.You need to develop small blocks of functionality, Test it by putting in some alerts  and console.log. Set breakpoints and monitor the DOM via Firebug and some IE development toolsPerformance - It happens all the time. But you should look at the tradeoffs. More time may give you more functionality.Consistency - ”But it works fine on my computer. So test on many browsers.  Take into account client resourcesHarm the Farm -  You need to code wisely and negatively test.  Don’t be the cause of a DoS attack that’s really JQuery asking for a resource over and over and over again.  So code wisely. Do negative testing. Monitor Server Resources.They also did a demo where JQuery did an endless loop to pull data from a list. It’s a poor decision but also an easy mistake.  They spiked their server resources within a couple seconds and had to shut down the call before it brought it down.ConclusionJQuery is now another tool in your tool kit. You don’t have to use it. Use it where it makes sense and where it helps you get your job done.Don’t abuse it, you will pay for it laterIt will add to page bloat so take that into accountIt can slow your performance

  Read the article

• Airline mess - what a journey

  - by Mike Dietrich

  What a day, what a journey ... Flew this noon from Munich to Zuerich for catch my ongoing flight to San Francisco with Swiss. And that day did start very well as Lufthansa messed up the connection flight by 42 minutes for a 35 minute flight. And as I was obviously the only passenger connection to San Francisco nobody picked me up at the airplane to bring me directly to my connection as Swiss did for the 8 passengers connection to Miami. So I missed my flight. What a start - and many thanks to Lufthansa. I was not the only one missing a connection as Lufthansa/Swiss had canceled the flight before due to "technical problems". In Zuerich Swiss did rebook me via Frankfurt with Lufthansa to board a United Airlines flight to San Francisco. "Ouch" I thought. I had my share of experience with United already as they've messed up my luggage on the way to San Francisco some years ago and it took them five (!!!) days to fly my bag over and deliver it. But actually it was the only option today. So I said "Yes". A big mistake as I've learned later on. The Frankfurt flight was delayed as well "due to a late incoming aircraft". But there was plenty of time. And I went to the Swiss counter at the gate and let them check if my baggage is on that flight to Frankfurt. They've said "Yes". Boarding the plane with a delay of 45 minutes (the typical Lufthansa delay these days) I spotted my Rimowa trolley right next to the plane on the airfield. So I was sure that it will be send to Frankfurt. In Frankfurt I went to the United counter once it did open - had to go through the passport check they do for US flights as well - and they've said "Yes, your luggage is with us". Well ... Arriving in San Francisco with just a bit of a some minutes delay and a very fast immigration procedure I saw the first bags with Priority tags getting pushed to the baggage claim - but mine was not there. I did wait ... and wait ... and wait. Well, thanks United, you did it again!!! I flew twice in the past years United Airlines - and in both cases they've messed up my luggage on the way to San Francisco. How lovely is that ... Now the real fun started again as the lady at the "Lost and Found" counter for luggage spotted my luggage in her system in Zuerich - and told me it's supposed to be sent with LH1191 to Frankfurt on Sept 27. But this was yesterday in Europe - it's already Sept 28 - and I saw my luggage in front of the airplane. So I'd suppose it's in Frankfurt already. But what could she do? Nothing but doing the awful paperwork. And "No Mr Dietrich, we don't call international numbers". Thank you, United. Next time I'll try to get a contract for a US land line in advance. They can't even tell you which plane will bring your luggage. It may be tomorrow with UA flight arriving around 4pm in SFO. I'm looking forward to some hours in the wonderful United Airlines call center waiting line. Last time I did spend 60-90 minutes every day until I got my luggage. If it takes again that long then OOW will be over by then. I love airline travel - and especially with United Airlines. And by the way ... they gave us these nice fancy packages during the flight:  That looks good - what's in that box??? Yes, really ... a bag of potato chips. Pure fat - very healthy.  I doubt that I'll ever fly United Airlines again!!!

  Read the article

• My error with upgrading 4.0 to 4.2- What NOT to do...

  - by Steve Tunstall

  Last week, I was helping a client upgrade from the 2011.1.4.0 code to the newest 2011.1.4.2 code. We downloaded the 4.2 update from MOS, upload and unpacked it on both controllers, and upgraded one of the controllers in the cluster with no issues at all. As this was a brand-new system with no networking or pools made on it yet, there were not any resources to fail back and forth between the controllers. Each controller had it's own, private, management interface (igb0 and igb1) and that's it. So we took controller 1 as the passive controller and upgraded it first. The first controller came back up with no issues and was now on the 4.2 code. Great. We then did a takeover on controller 1, making it the active head (although there were no resources for it to take), and then proceeded to upgrade controller 2. Upon upgrading the second controller, we ran the health check with no issues. We then ran the update and it ran and rebooted normally. However, something strange then happened. It took longer than normal to come back up, and when it did, we got the "cluster controllers on different code" error message that one gets when the two controllers of a cluster are running different code. But we just upgraded the second controller to 4.2, so they should have been the same, right??? Going into the Maintenance-->System screen of controller 2, we saw something very strange. The "current version" was still on 4.0, and the 4.2 code was there but was in the "previous" state with the rollback icon, as if it was the OLDER code and not the newer code. I have never seen this happen before. I would have thought it was a bad 4.2 code file, but it worked just fine with controller 1, so I don't think that was it. Other than the fact the code did not update, there was nothing else going on with this system. It had no yellow lights, no errors in the Problems section, and no errors in any of the logs. It was just out of the box a few hours ago, and didn't even have a storage pool yet. So.... We deleted the 4.2 code, uploaded it from scratch, ran the health check, and ran the upgrade again. once again, it seemed to go great, rebooted, and came back up to the same issue, where it came to 4.0 instead of 4.2. See the picture below.... HERE IS WHERE I MADE A BIG MISTAKE.... I SHOULD have instantly called support and opened a Sev 2 ticket. They could have done a shared shell and gotten the correct Fishwork engineer to look at the files and the code and determine what file was messed up and fixed it. The system was up and working just fine, it was just on an older code version, not really a huge problem at all. Instead, I went ahead and clicked the "Rollback" icon, thinking that the system would rollback to the 4.2 code.   Ouch... What happened was that the system said, "Fine, I will delete the 4.0 code and boot to your 4.2 code"... Which was stupid on my part because something was wrong with the 4.2 code file here and the 4.0 was just fine.  So now the system could not boot at all, and the 4.0 code was completely missing from the system, and even a high-level Fishworks engineer could not help us. I had messed it up good. We could only get to the ILOM, and I had to re-image the system from scratch using a hard-to-get-and-use FishStick USB drive. These are tightly controlled and difficult to get, almost always handcuffed to an engineer who will drive out to re-image a system. This took another day of my client's time.  So.... If you see a "previous version" of your system code which is actually a version higher than the current version... DO NOT ROLL IT BACK.... It did not upgrade for a very good reason. In my case, after the system was re-imaged to a code level just 3 back, we once again tried the same 4.2 code update and it worked perfectly the first time and is now great and stable.  Lesson learned.  By the way, our buddy Ryan Matthews wanted to point out the best practice and supported way of performing an upgrade of an active/active ZFSSA, where both controllers are doing some of the work. These steps would not have helpped me for the above issue, but it's important to follow the correct proceedure when doing an upgrade. 1) Upload software to both controllers and wait for it to unpack 2) On controller "A" navigate to configuration/cluster and click "takeover" 3) Wait for controller "B" to finish restarting, then login to it, navigate to maintenance/system, and roll forward to the new software. 4) Wait for controller "B" to apply the update and finish rebooting 5) Login to controller "B", navigate to configuration/cluster and click "takeover" 6) Wait for controller "A" to finish restarting, then login to it, navigate to maintenance/system, and roll forward to the new software. 7) Wait for controller "A" to apply the update and finish rebooting 8) Login to controller "B", navigate to configuration/cluster and click "failback"

  Read the article

• SQL SERVER – Backing Up and Recovering the Tail End of a Transaction Log – Notes from the Field #042

  - by Pinal Dave

  [Notes from Pinal]: The biggest challenge which people face is not taking backup, but the biggest challenge is to restore a backup successfully. I have seen so many different examples where users have failed to restore their database because they made some mistake while they take backup and were not aware of the same. Tail Log backup was such an issue in earlier version of SQL Server but in the latest version of SQL Server, Microsoft team has fixed the confusion with additional information on the backup and restore screen itself. Now they have additional information, there are a few more people confused as they have no clue about this. Previously they did not find this as a issue and now they are finding tail log as a new learning. Linchpin People are database coaches and wellness experts for a data driven world. In this 42nd episode of the Notes from the Fields series database expert Tim Radney (partner at Linchpin People) explains in a very simple words, Backing Up and Recovering the Tail End of a Transaction Log. Many times when restoring a database over an existing database SQL Server will warn you about needing to make a tail end of the log backup. This might be your reminder that you have to choose to overwrite the database or could be your reminder that you are about to write over and lose any transactions since the last transaction log backup. You might be asking yourself “What is the tail end of the transaction log”. The tail end of the transaction log is simply any committed transactions that have occurred since the last transaction log backup. This is a very crucial part of a recovery strategy if you are lucky enough to be able to capture this part of the log. Most organizations have chosen to accept some amount of data loss. You might be shaking your head at this statement however if your organization is taking transaction logs backup every 15 minutes, then your potential risk of data loss is up to 15 minutes. Depending on the extent of the issue causing you to have to perform a restore, you may or may not have access to the transaction log (LDF) to be able to back up those vital transactions. For example, if the storage array or disk that holds your transaction log file becomes corrupt or damaged then you wouldn’t be able to recover the tail end of the log. If you do have access to the physical log file then you can still back up the tail end of the log. In 2013 I presented a session at the PASS Summit called “The Ultimate Tail Log Backup and Restore” and have been invited back this year to present it again. During this session I demonstrate how you can back up the tail end of the log even after the data file becomes corrupt. In my demonstration I set my database offline and then delete the data file (MDF). The database can’t become more corrupt than that. I attempt to bring the database back online to change the state to RECOVERY PENDING and then backup the tail end of the log. I can do this by specifying WITH NO_TRUNCATE. Using NO_TRUNCATE is equivalent to specifying both COPY_ONLY and CONTINUE_AFTER_ERROR. It as its name says, does not try to truncate the log. This is a great demo however how could I achieve backing up the tail end of the log if the failure destroys my entire instance of SQL and all I had was the LDF file? During my demonstration I also demonstrate that I can attach the log file to a database on another instance and then back up the tail end of the log. If I am performing proper backups then my most recent full, differential and log files should be on a server other than the one that crashed. I am able to achieve this task by creating new database with the same name as the failed database. I then set the database offline, delete my data file and overwrite the log with my good log file. I attempt to bring the database back online and then backup the log with NO_TRUNCATE just like in the first example. I encourage each of you to view my blog post and watch the video demonstration on how to perform these tasks. I really hope that none of you ever have to perform this in production, however it is a really good idea to know how to do this just in case. It really isn’t a matter of “IF” you will have to perform a restore of a production system but more of a “WHEN”. Being able to recover the tail end of the log in these sever cases could be the difference of having to notify all your business customers of data loss or not. If you want me to take a look at your server and its settings, or if your server is facing any issue we can Fix Your SQL Server. Note: Tim has also written an excellent book on SQL Backup and Recovery, a must have for everyone. Reference: Pinal Dave (http://blog.sqlauthority.com)Filed under: Notes from the Field, PostADay, SQL, SQL Authority, SQL Performance, SQL Query, SQL Server, SQL Tips and Tricks, T SQL

  Read the article

• Lessons learnt in implementing Scrum in a Large Organization that has traditional values

  - by MarkPearl

  I recently had the experience of being involved in a “test” scrum implementation in a large organization that was used to a traditional project management approach. Here are some lessons that I learnt from it. Don’t let the Project Manager be the Product Owner First lesson learnt is to identify the correct product owner – in this instance the product manager assumed the role of the product owner which was a mistake. The product owner is the one who has the most to loose if the project fails. With a methodology that advocates removing the role of the project manager from the process then it is not in the interests of the person who is employed as a project manager to be the product owner – in fact they have the most to gain should the project fail. Know the time commitments of team members to the Project Second lesson learnt is to get a firm time commitment of the members on a team for the sprint and to hold them to it. In this project instance many of the issues we faced were with team members having to double up on supporting existing projects/systems and the scrum project. In many situations they just didn’t get round to doing any work on the scrum project for several days while they tried to meet other commitments. Initially this was not made transparent to the team – in stand up team members would say that had done some work but would be very vague on how much time they had actually spent using the blackhole of their other legacy projects as an excuse – putting up a time burn down chart made time allocations transparent and easy to hold the team to. In addition, how can you plan for a sprint without knowing the actual time available of the members – when I mean actual time, the exercise of getting them to go through all their appointments and lunch times and breaks and removing them from their time commitment helps get you to a realistic time that they can dedicate. Make sure you meet your minimum team sizes In a recent post I wrote about the difference between a partnership and a team. If you are going to do scrum in a large organization make sure you have a minimum team size of at least 3 developers. My experience with larger organizations is that people have a tendency to be sick more, take more leave and generally not be around – if you have a team size of two it is so easy to loose momentum on the project – the more people you have in the team (up to about 9) the more the momentum the project will have when people are not around. Swapping from one methodology to another can seem as waste to the customer It sounds bad, but most customers don’t care what methodology you use. Often they have bought into the “big plan upfront”. If you can, avoid taking a project on midstream from a traditional approach unless the customer has not bought into the process – with this particular project they had a detailed upfront planning breakaway with the customer using the traditional approach and then before the project started we moved onto a scrum implementation – this seemed as waste to the customer. We should have managed the customers expectation properly. Don’t play the role of the scrum master if you can’t be the scrum master With this particular implementation I was the “scrum master”. But all I did was go through the process of the formal meetings of scrum – I attended stand up, retrospectives and planning – but I was not hands on the ground. I was not performing the most important role of removing blockages – and by the end of the project there were a number of blockages “cropping up”. What could have been a better approach was to take someone on the team and train them to be the scrum master and be present to coach them. Alternatively actually be on the team on a fulltime basis and be the scrum master. By just going through the meetings of scrum didn’t mean we were doing scrum. So we failed with this one, if you fail look at it from an agile perspective As this particular project drew to a close and it became more and more apparent that it was not going to succeed the failure of it became depressing. Emotions were expressed by various people on the team that we not encouraging and enforced the failure. Embracing the failure and looking at it for what it is instead of taking it as the end of the world can change how you grow from the experience. Acknowledging that it failed and then focussing on learning from why and how to avoid the failure in the future can change how you feel emotionally about the team, the project and the organization.

  Read the article

• Encrypt images before uploading to Dropbox [migrated]

  - by Cherry

  I want to encrypt a file first before the file will be uploaded to the dropbox. So i have implement the encryption inside the uploading of the codes. However, there is an error after i integrate the codes together. Where did my mistake go wrong? Error at putFileOverwriteRequest and it says The method putFileOverwriteRequest(String, InputStream, long, ProgressListener) in the type DropboxAPI is not applicable for the arguments (String, FileOutputStream, long, new ProgressListener(){}) Another problem is that this FileOutputStream fis = new FileOutputStream(new File("dont know what to put in this field")); i do not know where to put the file so that after i read the file, it will call the path and then upload to the Dropbox. Anyone is kind to help me in this? As time is running out for me and i still cant solve the problem. Thank you in advance. The full code is as below. public class UploadPicture extends AsyncTask<Void, Long, Boolean> { private DropboxAPI<?> mApi; private String mPath; private File mFile; private long mFileLen; private UploadRequest mRequest; private Context mContext; private final ProgressDialog mDialog; private String mErrorMsg; public UploadPicture(Context context, DropboxAPI<?> api, String dropboxPath, File file) { // We set the context this way so we don't accidentally leak activities mContext = context.getApplicationContext(); mFileLen = file.length(); mApi = api; mPath = dropboxPath; mFile = file; mDialog = new ProgressDialog(context); mDialog.setMax(100); mDialog.setMessage("Uploading " + file.getName()); mDialog.setProgressStyle(ProgressDialog.STYLE_HORIZONTAL); mDialog.setProgress(0); mDialog.setButton("Cancel", new OnClickListener() { public void onClick(DialogInterface dialog, int which) { // This will cancel the putFile operation mRequest.abort(); } }); mDialog.show(); } @Override protected Boolean doInBackground(Void... params) { try { KeyGenerator keygen = KeyGenerator.getInstance("DES"); SecretKey key = keygen.generateKey(); //generate key //encrypt file here first byte[] plainData; byte[] encryptedData; Cipher cipher = Cipher.getInstance("DES/ECB/PKCS5Padding"); cipher.init(Cipher.ENCRYPT_MODE, key); //File f = new File(mFile); //read file FileInputStream in = new FileInputStream(mFile); //obtains input bytes from a file plainData = new byte[(int)mFile.length()]; in.read(plainData); //Read bytes of data into an array of bytes encryptedData = cipher.doFinal(plainData); //encrypt data FileOutputStream fis = new FileOutputStream(new File("dont know what to put in this field")); //upload to a path first then call the path so that it can be uploaded up to the dropbox //save encrypted file to dropbox // By creating a request, we get a handle to the putFile operation, // so we can cancel it later if we want to //FileInputStream fis = new FileInputStream(mFile); String path = mPath + mFile.getName(); mRequest = mApi.putFileOverwriteRequest(path, fis, mFile.length(), new ProgressListener() { @Override public long progressInterval() { // Update the progress bar every half-second or so return 500; } @Override public void onProgress(long bytes, long total) { publishProgress(bytes); } }); if (mRequest != null) { mRequest.upload(); return true; } } catch (DropboxUnlinkedException e) { // This session wasn't authenticated properly or user unlinked mErrorMsg = "This app wasn't authenticated properly."; } catch (DropboxFileSizeException e) { // File size too big to upload via the API mErrorMsg = "This file is too big to upload"; } catch (DropboxPartialFileException e) { // We canceled the operation mErrorMsg = "Upload canceled"; } catch (DropboxServerException e) { // Server-side exception. These are examples of what could happen, // but we don't do anything special with them here. if (e.error == DropboxServerException._401_UNAUTHORIZED) { // Unauthorized, so we should unlink them. You may want to // automatically log the user out in this case. } else if (e.error == DropboxServerException._403_FORBIDDEN) { // Not allowed to access this } else if (e.error == DropboxServerException._404_NOT_FOUND) { // path not found (or if it was the thumbnail, can't be // thumbnailed) } else if (e.error == DropboxServerException._507_INSUFFICIENT_STORAGE) { // user is over quota } else { // Something else } // This gets the Dropbox error, translated into the user's language mErrorMsg = e.body.userError; if (mErrorMsg == null) { mErrorMsg = e.body.error; } } catch (DropboxIOException e) { // Happens all the time, probably want to retry automatically. mErrorMsg = "Network error. Try again."; } catch (DropboxParseException e) { // Probably due to Dropbox server restarting, should retry mErrorMsg = "Dropbox error. Try again."; } catch (DropboxException e) { // Unknown error mErrorMsg = "Unknown error. Try again."; } catch (FileNotFoundException e) { } return false; } @Override protected void onProgressUpdate(Long... progress) { int percent = (int)(100.0*(double)progress[0]/mFileLen + 0.5); mDialog.setProgress(percent); } @Override protected void onPostExecute(Boolean result) { mDialog.dismiss(); if (result) { showToast("Image successfully uploaded"); } else { showToast(mErrorMsg); } } private void showToast(String msg) { Toast error = Toast.makeText(mContext, msg, Toast.LENGTH_LONG); error.show(); } }

  Read the article

• WPF: Setting DataContext of a UserControl with Binding not working in XAML

  - by Grant Crofton

  Hi, I'm trying to get my first WPF app working using MVVM, and I've hit a little binding problem. The setup is that I have a view & viewModel which holds User details (the parent), and to try and keep things simple I've put a section of that view into a separate view & viewModel (the child). The child view is defined as a UserControl. The issue I'm having is how to set the DataContext of the child view (the UserControl). My parent ViewModel has a property which exposes the child ViewModel, like so: class ParentViewModel: INotifyPropertyChanged { public ChildViewModel childViewModel { get; set; } //... } In the XAML for my parent view (which has it's DataContext set to the ParentViewModel), I try to set the DataContext of the child view as follows: <views:ChildView x:Name="ChildView" DataContext="{Binding childViewModel}"/> However, this doesn't work. The DataContext of the child view is set to the same DataContext as the parent view (i.e. the ParentViewModel), as if I wasn't setting it at all. I also tried setting the DataContext in the child view itself, which also doesn't work: <UserControl x:Class="DietRecorder.Client.View.ChildView" DataContext="childViewModel" I have found a couple of ways around this. In the child view, I can bind everything by including the ChildViewModel in the path: <SomeControl Visibility="{Binding Path=childViewModel.IsVisible}"> but I don't want the child view to have this level of awareness of the hierarchy. Setting the DataContext in code also works - however, I have to do this after showing the parent view, otherwise the DataContext just gets overwritten when I call Show(): parentView.Show(); parentView.ChildView.DataContext = parentViewModel.childViewModel; This code also makes me feel uneasy, what with the LOD violation and all. It's just the DataContext that seems to be the problem - I can bind other things in the child, for example I tried binding the FontSize to an int property just to test it: <views:ChildView x:Name="ChildView" FontSize="{Binding Path=someVal}"/> And that works fine. But I'm sure binding the DataContext should work - I've seen similar examples of this kind of thing. Have I missed something obvious here? Is there a reason this won't work? Is there a spelling mistake somewhere? (I renamed things for your benefit so you won't be able to help me there anyway). Any thoughts welcome. Thanks, Grant

  Read the article

• OSGI & Apache Commons-DBCP Classloading Issue

  - by Saul

  I inherited some code that is using the Apache commons-dbcp Connection pools in an OSGi bundle. This code works fine with Eclipse/Equinox OSGi version 3.4.3 (R34x_v20081215), commons-dbcp 1.2.2 and the postgres jdbc3 8.3.603 bundles from springsource.org. I wanted to modernize, maybe this was my first mistake! When I use the new version of Felix or Equinox OSGI Cores with the new postgresql JDBC3 or JDBC4 bundles along with the latest version of commons-dbcp (1.4.1), I am getting a classloading issue. I have done numerous searches and found that the commons-dbcp code should have a fix DBCP-214, but it still seems to fail. I have tried to put the org.postgresql on the commons-dbcp MANIFEST.MF import-package line, but that did not work either. I wrote a simple test in an activator that first does a basic class.forName() and DriverManager.getConnection(), this works fine, but when I add in BasicDataSource() and setup the connection with BasicDataSource.getConnection(), I get the ClassNotFoundException. See the code example below. Thanks in Advance for any help, suggestions, ... Sau! // This one fails with an exception public void dsTest() { BasicDataSource bds = new BasicDataSource(); ClassLoader cl; try { logger.debug("ContextClassLoader: {}", Thread.currentThread().getContextClassLoader().toString()); cl = this.getClass().getClassLoader(); logger.debug("ClassLoader: {}", cl); if (bds.getDriverClassLoader() != null) { logger.debug(bds.getDriverClassLoader().toString()); } // The failure is the same with and with the setDriverClassLoader() line bds.setDriverClassLoader(cl); bds.setDriverClassName("org.postgresql.Driver"); bds.setUrl("jdbc:postgresql://127.0.0.1/dbname"); bds.setUsername("user"); bds.setPassword("pword"); Class.forName("org.postgresql.Driver").newInstance(); conn = bds.getConnection(); Statement st = conn.createStatement(); ResultSet rs = st.executeQuery("SELECT COUNT(*) FROM table"); conn.close(); logger.debug("Closed DataSource Test"); } catch (Exception ex) { ex.printStackTrace(); logger.debug("Exception: {} ", ex.getMessage()); } } // This one works public void managerTest() { ClassLoader cl; try { cl = this.getClass().getClassLoader(); logger.debug("ClassLoader: {}", cl); Class.forName("org.postgresql.Driver").newInstance(); String url = "jdbc:postgresql://127.0.0.1/dbname"; conn = DriverManager.getConnection(url, "user", "pword"); Statement st = conn.createStatement(); ResultSet rs = st.executeQuery("SELECT COUNT(*) FROM table"); conn.close(); logger.debug("Closed Manger Test"); } catch (Exception ex) { ex.printStackTrace(); logger.debug("Exception: {} ", ex.getMessage()); } }

  Read the article

• Macro doesn't work in the function.

  - by avp

  I have problems with following code: http://lisper.ru/apps/format/96 The problem is in "normalize" function, which does not work. It fails on the fifth line: (zero-p a indexes i) (defun normalize (a &optional indexes i) "Returns normalized A." (pragma (format t "Data=~A ~A ~A" a indexes i) (if (zero-p a indexes i) a ;; cannot normalize empty vector (let* ((mmm (format t "Zero?=~a" (zero-p a indexes i))) (L (sqrt (+ (do-op-on * a :x a :x indexes i indexes i) (do-op-on * a :y a :y indexes i indexes i) (do-op-on * a :z a :z indexes i indexes i)))) (mmm (format t "L=~a" L)) (L (/ 1D0 L)) (mmm (format t "L=~a" L))) ; L=1/length(A) (make-V3 (* (ref-of a :x indexes i) l) (* (ref-of a :y indexes i) l) (* (ref-of a :z indexes i) l)))))) in function "normalize" I call the macro "zero-p", which in turn calls macro "ref-of", which is the last in the chain. (defmacro zero-p (v &optional indexes index) "Checks if the vector is 'almost' zero length." `(and (< (ref-of ,v :x ,indexes ,index) *min+*) (< (ref-of ,v :y ,indexes ,index) *min+*) (< (ref-of ,v :z ,indexes ,index) *min+*) (> (ref-of ,v :x ,indexes ,index) *min-*) (> (ref-of ,v :y ,indexes ,index) *min-*) (> (ref-of ,v :z ,indexes ,index) *min-*))) Here is ref-of: (defmacro ref-of (values coordinate &optional indexes index) "Please see DATA STRUCTURE for details." (if indexes (cond ((eq coordinate :x) `(aref ,values (aref ,indexes ,index))) ((eq coordinate :y) `(aref ,values (+ 1 (aref ,indexes ,index)))) ((eq coordinate :z) `(aref ,values (+ 2 (aref ,indexes ,index)))) (T (error "The symbol ~S is not :X, :Y or :Z." coordinate))) (cond ((eq coordinate :x) `(aref ,values 0)) ((eq coordinate :y) `(aref ,values 1)) ((eq coordinate :z) `(aref ,values 2)) (T (error "The symbol ~S is not :X, :Y or :Z." coordinate))))) Also, in "normalize" I call the macro "do-op-on", which calls "ref-of" as well. (defmacro do-op-on (op name1 coord1 name2 coord2 &optional is1 i1 is2 i2) "Example: (do-op-on * A :x B :y i n) == A[i[n]].x*B.y" `(,op (ref-of ,name1 ,coord1 ,is1 ,i1) (ref-of ,name2 ,coord2 ,is2 ,i2))) As a result, instead of having this: (aref some-array 0) I have (aref NIL NIL) which is created in "ref-of". I suppose that I lose the symbol A from the call (normalize A). I just feel that the symbol does not survive the macroexpanson. The thing is, macroexpansoin works in REPL for each macro independently. Can anyone explain where is the mistake?

  Read the article

• Zend Framework + Uplodify Flash Uploader Troubles

  - by Richard Knop

  I've been trying to get the Uploadify flash uploader (www.uploadify.com) to work with Zend Framework, with no success so far. I have placed all Uploadify files under /public/flash-uploader directory. In the controller I include all required files and libraries like this: $this->view->headScript()->appendFile('/js/jquery-1.3.2.min.js'); $this->view->headLink()->appendStylesheet('/flash-uploader/css/default.css'); $this->view->headLink()->appendStylesheet('/flash-uploader/css/uploadify.css'); $this->view->headScript()->appendFile('/flash-uploader/scripts/swfobject.js'); $this->view->headScript()->appendFile('/flash-uploader/scripts/jquery.uploadify.v2.1.0.min.js'); And then I activate the plugin like this (#photo is id of the input file field): $(document).ready(function() { $("#photo").uploadify({ 'uploader' : '/flash-uploader/scripts/uploadify.swf', 'script' : 'my-account/flash-upload', 'cancelImg' : '/flash-uploader/cancel.png', 'folder' : 'uploads/tmp', 'queueID' : 'fileQueue', 'auto' : true, 'multi' : true, 'sizeLimit' : 2097152 }); }); As you can see I am targeting the my-account/flash-upload script as a backend processing (my-account is a controller, flash-upload is an action). My form markup looks like this: <form enctype="multipart/form-data" method="post" action="/my-account/upload-public-photo"><ol> <li><label for="photo" class="optional">File Queue<div id="fileQueue"></div></label> <input type="hidden" name="MAX_FILE_SIZE" value="31457280" id="MAX_FILE_SIZE" /> <input type="file" name="photo" id="photo" class="input-file" /></li> <li><div class="button"> <input type="submit" name="upload_public_photo" id="upload_public_photo" value="Save" class="input-submit" /></div></li></ol></form> And yet it's not working. The browse button doesn't even show up as in the demo page, I get only a regular input file field. Any ideas where could the problem be? I've already been staring into the code for hours and I cannot see any mistake anywhere and I'm starting to be exhausted after going through the same 30 lines of code 30 times in a row.

  Read the article

• jBASE 4.1 Database Noobster Questions

  - by Steve Johnson

  I am a software developer with devlopment experience in C#, C++ .Net alongwith SQL Server 2005/08, Oracle and mysql. But somehow i dont get jBASE to work at Windows XP SP3 machine. My goal is setup user accounts, create database on a JBASE ainstallation, authenticate and backup/restore few table via a C++ program. And i dont need to do it with builtin backup/restore tools of jBASE. I am able to install jBASe 4.1 aling with all its accessories on my WINXPSP3 machine. I was able to run the jSlimserver and TEMENOUS server along with licnesing server. I was able to add the license key as well. But after that what i was supposed to do? i have no idea about it. The docs and online help doesnt answer a simple question of how to create a database! The google search results from the jbase site all go to the 404 Pages! Can a jBASE expert guide to the following steps: Create a jBASE database. Create users Authenticate via those users Connect to database Create tables and insert data. Connect via a C++ or C# program to connect to jBASE DB and backup/restore tables. I know that this is too much too ask but i dont get to get the JBASE system. I cant get it to work on my System somehow. Btw, jdc and jexloree doesnt seem to do anything. I have checked that enironmental variables for jBASE are setup correctly and i have verified them. There are no extra JRE or JDK installations on my system. Besides all that, only licensing client, slim server and temenous server seem to run and listen for connections and no other execuatable ever seems to work. A simple tutorial to achieve the objective will be highly appreciated. Also if anyone can point out the mistake that i have done or anything i might need to check, then please do so. I will be highly encouraged and obliged. Thanks Steve

  Read the article

< Previous Page | 54 55 56 57 58 59 60 61 62 63 64 65  | Next Page >